| Message ID | 20231025210342.30995-1-laurent.pinchart@ideasonboard.com |
|---|---|
| Headers | show |
| Series | arm64: dts: mediatek: Add device tree for MT8365-based Pumpkin i350 | expand |
Hi Angelo, On Tue, Jan 23, 2024 at 02:53:58PM +0100, AngeloGioacchino Del Regno wrote: > Il 25/10/23 23:03, Laurent Pinchart ha scritto: > > Add a minimal device tree for the Genio i350 Pumpkin development board, > > which is based on a MediaTek MT8365. > > > > The device tree is based on an initial version by Fabien Parent Based > > written against the MediaTek BSP kernel ([1]). It has been cleaned up, > > some features have been added (GPIO LEDs, ethernet), and some features > > removed (audio, camera, display and dual-role USB). Those features will > > be added back once the corresponding DT bindings and/or drivers become > > available in the upstream kernel. > > > > [1] https://gitlab.com/mediatek/aiot/bsp/linux/-/blob/mtk-v5.15-dev/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > > > Co-developed-by: Fabien Parent <fparent@baylibre.com> > > Signed-off-by: Fabien Parent <fparent@baylibre.com> > > Co-developed-by: Paul Elder <paul.elder@ideasonboard.com> > > Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> > > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > --- > > Changes since v1: > > > > - Drop mmc2 alias > > - Reorder properties of i2c, mmc and usb nodes > > > > Changes compared to the BSP version: > > > > - Add ethernet controller > > - Add GPIO LEDs > > - Add reserved memory region for BL31 > > - Update board model and compatible > > - Rename enable-sdio-wakeup to wakeup-source > > - Drop audio support > > - Drop display support > > - Drop dual role USB support > > - Don't use underscores in node names > > - Normalize pinmux node names > > - Remove unneeded labels > > - Drop unneeded always-on > > - Drop unused pinmux nodes > > - Drop camera GPIO hog > > - Update copyright > > - Fix formatting > > - Sort alphabetically > > --- > > arch/arm64/boot/dts/mediatek/Makefile | 1 + > > .../boot/dts/mediatek/mt8365-pumpkin.dts | 541 ++++++++++++++++++ > > 2 files changed, 542 insertions(+) > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > > index c99c3372a4b5..bbc232bdadc4 100644 > > --- a/arch/arm64/boot/dts/mediatek/Makefile > > +++ b/arch/arm64/boot/dts/mediatek/Makefile > > @@ -53,4 +53,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-pumpkin.dtb > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb > > diff --git a/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > new file mode 100644 > > index 000000000000..9c75294c9889 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts > > @@ -0,0 +1,541 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (c) 2021 BayLibre, SAS. > > + * Copyright (c) 2023 Ideas on Board Oy > > + * > > + * Author: Fabien Parent <fparent@baylibre.com> > > + */ > > + > > +/dts-v1/; > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/leds/common.h> > > +#include <dt-bindings/pinctrl/mt8365-pinfunc.h> > > + > > +#include "mt8365.dtsi" > > +#include "mt6357.dtsi" > > + > > +/ { > > + model = "OLogic Pumpkin i350 EVK"; > > + compatible = "ologic,pumpkin-i350", "mediatek,mt8365"; > > + > > + aliases { > > + ethernet0 = ðernet_usb; > > + mmc0 = &mmc0; > > + mmc1 = &mmc1; > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:921600n8"; > > + }; > > + > > + firmware { > > + optee { > > + compatible = "linaro,optee-tz"; > > + method = "smc"; > > + }; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led-red { > > + gpios = <&gpio_exp 12 GPIO_ACTIVE_HIGH>; > > + color = <LED_COLOR_ID_RED>; > > + function = LED_FUNCTION_HEARTBEAT; > > + linux,default-trigger = "heartbeat"; > > + }; > > + > > + led-green { > > + gpios = <&gpio_exp 13 GPIO_ACTIVE_HIGH>; > > + color = <LED_COLOR_ID_GREEN>; > > + default-state = "off"; > > + }; > > + }; > > + > > + memory@40000000 { > > + device_type = "memory"; > > + reg = <0 0x40000000 0 0x80000000>; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ > > + secmon@43000000 { > > + no-map; > > + reg = <0 0x43000000 0 0x30000>; > > reg first, no-map last. > > > + }; > > + > > + /* > > + * 12 MiB reserved for OP-TEE (BL32) > > + * +-----------------------+ 0x43e0_0000 > > + * | SHMEM 2MiB | > > + * +-----------------------+ 0x43c0_0000 > > + * | | TA_RAM 8MiB | > > + * + TZDRAM +--------------+ 0x4340_0000 > > + * | | TEE_RAM 2MiB | > > + * +-----------------------+ 0x4320_0000 > > + */ > > + optee@43200000 { > > + no-map; > > + reg = <0 0x43200000 0 0x00c00000>; > > same here. > > > + }; > > + }; > > + > > + usb_otg_vbus: usb-otg-vbus-regulator { > > + compatible = "regulator-fixed"; > > + regulator-name = "otg_vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + gpio = <&pio 25 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > +}; > > + > > +&cpu0 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&cpu1 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&cpu2 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&cpu3 { > > + proc-supply = <&mt6357_vproc_reg>; > > + sram-supply = <&mt6357_vsram_proc_reg>; > > +}; > > + > > +&i2c0 { > > + clock-frequency = <100000>; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c0_pins>; > > + > > + status = "okay"; > > +}; > > + > > +&i2c1 { > > + clock-frequency = <100000>; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c1_pins>; > > + > > + status = "okay"; > > + > > + gpio_exp: gpio@20 { > > + compatible = "ti,tca6416"; > > + reg = <0x20>; > > + reset-gpios = <&pio 78 GPIO_ACTIVE_LOW>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&tca6416_pins>; > > + > > + gpio-controller; > > Please check Documentation/devicetree/bindings/dts-coding-style.rst I assume you mean the "Order of Properties in Device Node" section ? What part exactly ? > > + #gpio-cells = <2>; > > + }; > > +}; > > + > > +&i2c2 { > > + clock-frequency = <100000>; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c2_pins>; > > + > > + status = "okay"; > > +}; > > + > > +&i2c3 { > > + clock-frequency = <100000>; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c3_pins>; > > + > > + status = "okay"; > > +}; > > + > > +&keypad { > > + status = "okay"; > > status goes last. > > Please check Documentation/devicetree/bindings/dts-coding-style.rst > > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&keypad_pins>; > > + > > + keypad,num-rows = <2>; > > + keypad,num-columns = <1>; > > + mediatek,debounce-us = <32000>; > > + mediatek,double-keys; > > + > > + linux,keymap = <MATRIX_KEY(0x00, 0x00, KEY_VOLUMEDOWN) > > + MATRIX_KEY(0x01, 0x00, KEY_VOLUMEUP)>; > > +}; > > + > > +/* eMMC */ > > +&mmc0 { > > + bus-width = <8>; > > + max-frequency = <200000000>; > > + > > + cap-mmc-highspeed; > > + cap-mmc-hw-reset; > > + hs400-ds-delay = <0x12012>; > > + mmc-hs200-1_8v; > > + mmc-hs400-1_8v; > > + no-sd; > > + no-sdio; > > + non-removable; > > Please order by name. > > > + > > + vmmc-supply = <&mt6357_vemc_reg>; > > + vqmmc-supply = <&mt6357_vio18_reg>; > > + > > + pinctrl-names = "default", "state_uhs"; > > + pinctrl-0 = <&mmc0_pins_default>; > > + pinctrl-1 = <&mmc0_pins_uhs>; > > + > > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; > > assigned clocks and clock parents go first. > > > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; > > + > > + status = "okay"; > > +}; > > + > > +/* SD card connector */ > > +&mmc1 { > > + bus-width = <4>; > > + max-frequency = <200000000>; > > + > > + cap-sd-highspeed; > > + cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>; > > + sd-uhs-sdr104; > > + sd-uhs-sdr50; > > Please order by name. > > > + > > + vmmc-supply = <&mt6357_vmch_reg>; > > + vqmmc-supply = <&mt6357_vmc_reg>; > > + > > + pinctrl-names = "default", "state_uhs"; > > + pinctrl-0 = <&mmc1_pins_default>; > > + pinctrl-1 = <&mmc1_pins_uhs>; > > + > > + status = "okay"; > > +}; > > + > > +/* WiFi module */ > > +&mmc2 { > > + bus-width = <4>; > > + max-frequency = <200000000>; > > + > > + cap-sd-highspeed; > > + cap-sdio-irq; > > + wakeup-source; > > + hs400-ds-delay = <0x12012>; > > Please order by name. > > > + keep-power-in-suspend; > > + non-removable; > > + sd-uhs-sdr104; > > + sd-uhs-sdr25; > > + sd-uhs-sdr50; > > + > > + vmmc-supply = <&mt6357_vemc_reg>; > > + vqmmc-supply = <&mt6357_vio18_reg>; > > + > > + pinctrl-names = "default", "state_uhs"; > > + pinctrl-0 = <&mmc2_pins_default>; > > + pinctrl-1 = <&mmc2_pins_uhs>; > > + > > + assigned-clocks = <&topckgen CLK_TOP_MSDC50_2_SEL>; > > + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; > > + > > + status = "okay"; > > +}; > > + > > +&mt6357_pmic { > > + interrupt-parent = <&pio>; > > + interrupts = <145 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > +}; > > + > > +&pio { > > + i2c0_pins: i2c0-pins { > > + pins { > > + pinmux = <MT8365_PIN_57_SDA0__FUNC_SDA0_0>, > > + <MT8365_PIN_58_SCL0__FUNC_SCL0_0>; > > + mediatek,pull-up-adv = <3>; > > + mediatek,drive-strength-adv = <00>; > > I don't know what 00 is here, and it's not a valid drive strength value in uA. I don't know either, I didn't author that part. I'll look it up. > Valid values are 125, 250, 500 and 1000 microamps. > > P.S.: Here and everywhere else. > > > + bias-pull-up; > > + }; > > + }; > > + > > + > > ..snip.. > > > + mmc0_pins_uhs: mmc0-uhs-pins{ > > + clk-pins { > > + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + cmd-dat-pins { > > + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>, > > + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>, > > + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>, > > + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>, > > + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>, > > + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>, > > + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>, > > + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>, > > + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>; > > + input-enable; > > + drive-strength = <MTK_DRIVE_10mA>; > > There's no need to use MTK_DRIVE_xxxx definitions, as they're really just defining > the same number that you can just clearly write. > > In this case, it is > drive-strength = <10>; > > please change it here and everywhere else. OK. Looks cleaner indeed. > > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; > > + }; > > + > > + ds-pins { > > + pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; > > + }; > > + > > + rst-pins { > > + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>; > > + drive-strength = <MTK_DRIVE_10mA>; > > + bias-pull-up; > > + }; > > + }; > > + > > ..snip.. > > > + > > +&usb_host { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + vusb33-supply = <&mt6357_vusb33_reg>; > > + > > + status = "okay"; > > + > > + hub@2 { > > + reg = <2>; > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + ethernet_usb: ethernet@1 { > > Can you please explain why you need this node on a fully discoverable bus? > Isn't it enough to just let USB auto enumerate this device at boot? To let the boot loader fill in the MAC address in DT. Would you like me to add a comment here ? > > + compatible = "usb424,ec00"; > > + reg = <1>; > > + }; > > + }; > > +};