| Message ID | 20-v8-81230027b2fa+9d-iommu_all_defdom_jgg@nvidia.com |
|---|---|
| State | New |
| Headers | show |
| Series | iommu: Make default_domain's mandatory | expand |
On Wed, 13 Sept 2023 at 16:45, Jason Gunthorpe <jgg@nvidia.com> wrote: > > At this point every iommu driver will cause a default_domain to be > selected, so we can finally remove this gap from the core code. > > The following table explains what each driver supports and what the > resulting default_domain will be: > > ops->defaut_domain > IDENTITY DMA PLATFORM v ARM32 dma-iommu ARCH > amd/iommu.c Y Y N/A either > apple-dart.c Y Y N/A either > arm-smmu.c Y Y IDENTITY either > qcom_iommu.c G Y IDENTITY either > arm-smmu-v3.c Y Y N/A either > exynos-iommu.c G Y IDENTITY either > fsl_pamu_domain.c Y Y N/A N/A PLATFORM > intel/iommu.c Y Y N/A either > ipmmu-vmsa.c G Y IDENTITY either > msm_iommu.c G IDENTITY N/A Unfortunately this patch breaks msm_iommu platforms. This driver doesn't select ARM_DMA_USE_IOMMU, so iommu_get_default_domain_type() returns 0, bus_iommu_probe() fails with -ENODEV. If I make MSM_IOMMU select ARM_DMA_USE_IOMMU, then GPU probing fails with -EBUSY. > mtk_iommu.c G Y IDENTITY either > mtk_iommu_v1.c G IDENTITY N/A > omap-iommu.c G IDENTITY N/A > rockchip-iommu.c G Y IDENTITY either > s390-iommu.c Y Y N/A N/A PLATFORM > sprd-iommu.c Y N/A DMA > sun50i-iommu.c G Y IDENTITY either > tegra-smmu.c G Y IDENTITY IDENTITY > virtio-iommu.c Y Y N/A either > spapr Y Y N/A N/A PLATFORM > * G means ops->identity_domain is used > * N/A means the driver will not compile in this configuration > > ARM32 drivers select an IDENTITY default domain through either the > ops->identity_domain or directly requesting an IDENTIY domain through > alloc_domain(). > > In ARM64 mode tegra-smmu will still block the use of dma-iommu.c and > forces an IDENTITY domain. > > S390 uses a PLATFORM domain to represent when the dma_ops are set to the > s390 iommu code. > > fsl_pamu uses an PLATFORM domain. > > POWER SPAPR uses PLATFORM and blocking to enable its weird VFIO mode. > > The x86 drivers continue unchanged. > > After this patch group->default_domain is only NULL for a short period > during bus iommu probing while all the groups are constituted. Otherwise > it is always !NULL. > > This completes changing the iommu subsystem driver contract to a system > where the current iommu_domain always represents some form of translation > and the driver is continuously asserting a definable translation mode. > > It resolves the confusion that the original ops->detach_dev() caused > around what translation, exactly, is the IOMMU performing after > detach. There were at least three different answers to that question in > the tree, they are all now clearly named with domain types. > > Tested-by: Heiko Stuebner <heiko@sntech.de> > Tested-by: Niklas Schnelle <schnelle@linux.ibm.com> > Tested-by: Steven Price <steven.price@arm.com> > Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> > Tested-by: Nicolin Chen <nicolinc@nvidia.com> > Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> > Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> > Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> > --- > drivers/iommu/iommu.c | 22 +++++++--------------- > 1 file changed, 7 insertions(+), 15 deletions(-) > > diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c > index 42a4585dd76da6..cfb597751f5bad 100644 > --- a/drivers/iommu/iommu.c > +++ b/drivers/iommu/iommu.c > @@ -1865,7 +1865,6 @@ static int iommu_get_def_domain_type(struct iommu_group *group, > static int iommu_get_default_domain_type(struct iommu_group *group, > int target_type) > { > - const struct iommu_ops *ops = group_iommu_ops(group); > struct device *untrusted = NULL; > struct group_device *gdev; > int driver_type = 0; > @@ -1876,11 +1875,13 @@ static int iommu_get_default_domain_type(struct iommu_group *group, > * ARM32 drivers supporting CONFIG_ARM_DMA_USE_IOMMU can declare an > * identity_domain and it will automatically become their default > * domain. Later on ARM_DMA_USE_IOMMU will install its UNMANAGED domain. > - * Override the selection to IDENTITY if we are sure the driver supports > - * it. > + * Override the selection to IDENTITY. > */ > - if (IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU) && ops->identity_domain) > + if (IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU)) { > + static_assert(!(IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU) && > + IS_ENABLED(CONFIG_IOMMU_DMA))); > driver_type = IOMMU_DOMAIN_IDENTITY; > + } > > for_each_group_device(group, gdev) { > driver_type = iommu_get_def_domain_type(group, gdev->dev, > @@ -3016,18 +3017,9 @@ static int iommu_setup_default_domain(struct iommu_group *group, > if (req_type < 0) > return -EINVAL; > > - /* > - * There are still some drivers which don't support default domains, so > - * we ignore the failure and leave group->default_domain NULL. > - */ > dom = iommu_group_alloc_default_domain(group, req_type); > - if (!dom) { > - /* Once in default_domain mode we never leave */ > - if (group->default_domain) > - return -ENODEV; > - group->default_domain = NULL; > - return 0; > - } > + if (!dom) > + return -ENODEV; > > if (group->default_domain == dom) > return 0; > -- > 2.42.0 >
On Tue, Oct 03, 2023 at 12:21:59AM +0300, Dmitry Baryshkov wrote: > On Wed, 13 Sept 2023 at 16:45, Jason Gunthorpe <jgg@nvidia.com> wrote: > > > > At this point every iommu driver will cause a default_domain to be > > selected, so we can finally remove this gap from the core code. > > > > The following table explains what each driver supports and what the > > resulting default_domain will be: > > > > ops->defaut_domain > > IDENTITY DMA PLATFORM v ARM32 dma-iommu ARCH > > amd/iommu.c Y Y N/A either > > apple-dart.c Y Y N/A either > > arm-smmu.c Y Y IDENTITY either > > qcom_iommu.c G Y IDENTITY either > > arm-smmu-v3.c Y Y N/A either > > exynos-iommu.c G Y IDENTITY either > > fsl_pamu_domain.c Y Y N/A N/A PLATFORM > > intel/iommu.c Y Y N/A either > > ipmmu-vmsa.c G Y IDENTITY either > > msm_iommu.c G IDENTITY N/A > > Unfortunately this patch breaks msm_iommu platforms. This driver > doesn't select ARM_DMA_USE_IOMMU, so iommu_get_default_domain_type() > returns 0, bus_iommu_probe() fails with -ENODEV. > If I make MSM_IOMMU select ARM_DMA_USE_IOMMU, then GPU probing fails > with -EBUSY. Oh, OK. Does this fix it? diff --git a/drivers/iommu/msm_iommu.c b/drivers/iommu/msm_iommu.c index cdc7b730192a35..f7ef081c33dcb2 100644 --- a/drivers/iommu/msm_iommu.c +++ b/drivers/iommu/msm_iommu.c @@ -685,10 +685,16 @@ irqreturn_t msm_iommu_fault_handler(int irq, void *dev_id) return 0; } +static int msm_iommu_def_domain_type(struct device *dev) +{ + return IOMMU_DOMAIN_IDENTITY; +} + static struct iommu_ops msm_iommu_ops = { .identity_domain = &msm_iommu_identity_domain, .domain_alloc_paging = msm_iommu_domain_alloc_paging, .probe_device = msm_iommu_probe_device, + .def_domain_type = msm_iommu_def_domain_type, .device_group = generic_device_group, .pgsize_bitmap = MSM_IOMMU_PGSIZES, .of_xlate = qcom_iommu_of_xlate,
On Tue, 3 Oct 2023 at 02:00, Jason Gunthorpe <jgg@nvidia.com> wrote: > > On Tue, Oct 03, 2023 at 12:21:59AM +0300, Dmitry Baryshkov wrote: > > On Wed, 13 Sept 2023 at 16:45, Jason Gunthorpe <jgg@nvidia.com> wrote: > > > > > > At this point every iommu driver will cause a default_domain to be > > > selected, so we can finally remove this gap from the core code. > > > > > > The following table explains what each driver supports and what the > > > resulting default_domain will be: > > > > > > ops->defaut_domain > > > IDENTITY DMA PLATFORM v ARM32 dma-iommu ARCH > > > amd/iommu.c Y Y N/A either > > > apple-dart.c Y Y N/A either > > > arm-smmu.c Y Y IDENTITY either > > > qcom_iommu.c G Y IDENTITY either > > > arm-smmu-v3.c Y Y N/A either > > > exynos-iommu.c G Y IDENTITY either > > > fsl_pamu_domain.c Y Y N/A N/A PLATFORM > > > intel/iommu.c Y Y N/A either > > > ipmmu-vmsa.c G Y IDENTITY either > > > msm_iommu.c G IDENTITY N/A > > > > Unfortunately this patch breaks msm_iommu platforms. This driver > > doesn't select ARM_DMA_USE_IOMMU, so iommu_get_default_domain_type() > > returns 0, bus_iommu_probe() fails with -ENODEV. > > If I make MSM_IOMMU select ARM_DMA_USE_IOMMU, then GPU probing fails > > with -EBUSY. > > Oh, OK. > > Does this fix it? It indeed fixes the issue, so could you please post it, adding: Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > diff --git a/drivers/iommu/msm_iommu.c b/drivers/iommu/msm_iommu.c > index cdc7b730192a35..f7ef081c33dcb2 100644 > --- a/drivers/iommu/msm_iommu.c > +++ b/drivers/iommu/msm_iommu.c > @@ -685,10 +685,16 @@ irqreturn_t msm_iommu_fault_handler(int irq, void *dev_id) > return 0; > } > > +static int msm_iommu_def_domain_type(struct device *dev) > +{ > + return IOMMU_DOMAIN_IDENTITY; > +} > + > static struct iommu_ops msm_iommu_ops = { > .identity_domain = &msm_iommu_identity_domain, > .domain_alloc_paging = msm_iommu_domain_alloc_paging, > .probe_device = msm_iommu_probe_device, > + .def_domain_type = msm_iommu_def_domain_type, > .device_group = generic_device_group, > .pgsize_bitmap = MSM_IOMMU_PGSIZES, > .of_xlate = qcom_iommu_of_xlate,
diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c index 42a4585dd76da6..cfb597751f5bad 100644 --- a/drivers/iommu/iommu.c +++ b/drivers/iommu/iommu.c @@ -1865,7 +1865,6 @@ static int iommu_get_def_domain_type(struct iommu_group *group, static int iommu_get_default_domain_type(struct iommu_group *group, int target_type) { - const struct iommu_ops *ops = group_iommu_ops(group); struct device *untrusted = NULL; struct group_device *gdev; int driver_type = 0; @@ -1876,11 +1875,13 @@ static int iommu_get_default_domain_type(struct iommu_group *group, * ARM32 drivers supporting CONFIG_ARM_DMA_USE_IOMMU can declare an * identity_domain and it will automatically become their default * domain. Later on ARM_DMA_USE_IOMMU will install its UNMANAGED domain. - * Override the selection to IDENTITY if we are sure the driver supports - * it. + * Override the selection to IDENTITY. */ - if (IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU) && ops->identity_domain) + if (IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU)) { + static_assert(!(IS_ENABLED(CONFIG_ARM_DMA_USE_IOMMU) && + IS_ENABLED(CONFIG_IOMMU_DMA))); driver_type = IOMMU_DOMAIN_IDENTITY; + } for_each_group_device(group, gdev) { driver_type = iommu_get_def_domain_type(group, gdev->dev, @@ -3016,18 +3017,9 @@ static int iommu_setup_default_domain(struct iommu_group *group, if (req_type < 0) return -EINVAL; - /* - * There are still some drivers which don't support default domains, so - * we ignore the failure and leave group->default_domain NULL. - */ dom = iommu_group_alloc_default_domain(group, req_type); - if (!dom) { - /* Once in default_domain mode we never leave */ - if (group->default_domain) - return -ENODEV; - group->default_domain = NULL; - return 0; - } + if (!dom) + return -ENODEV; if (group->default_domain == dom) return 0;
At this point every iommu driver will cause a default_domain to be selected, so we can finally remove this gap from the core code. The following table explains what each driver supports and what the resulting default_domain will be: ops->defaut_domain IDENTITY DMA PLATFORM v ARM32 dma-iommu ARCH amd/iommu.c Y Y N/A either apple-dart.c Y Y N/A either arm-smmu.c Y Y IDENTITY either qcom_iommu.c G Y IDENTITY either arm-smmu-v3.c Y Y N/A either exynos-iommu.c G Y IDENTITY either fsl_pamu_domain.c Y Y N/A N/A PLATFORM intel/iommu.c Y Y N/A either ipmmu-vmsa.c G Y IDENTITY either msm_iommu.c G IDENTITY N/A mtk_iommu.c G Y IDENTITY either mtk_iommu_v1.c G IDENTITY N/A omap-iommu.c G IDENTITY N/A rockchip-iommu.c G Y IDENTITY either s390-iommu.c Y Y N/A N/A PLATFORM sprd-iommu.c Y N/A DMA sun50i-iommu.c G Y IDENTITY either tegra-smmu.c G Y IDENTITY IDENTITY virtio-iommu.c Y Y N/A either spapr Y Y N/A N/A PLATFORM * G means ops->identity_domain is used * N/A means the driver will not compile in this configuration ARM32 drivers select an IDENTITY default domain through either the ops->identity_domain or directly requesting an IDENTIY domain through alloc_domain(). In ARM64 mode tegra-smmu will still block the use of dma-iommu.c and forces an IDENTITY domain. S390 uses a PLATFORM domain to represent when the dma_ops are set to the s390 iommu code. fsl_pamu uses an PLATFORM domain. POWER SPAPR uses PLATFORM and blocking to enable its weird VFIO mode. The x86 drivers continue unchanged. After this patch group->default_domain is only NULL for a short period during bus iommu probing while all the groups are constituted. Otherwise it is always !NULL. This completes changing the iommu subsystem driver contract to a system where the current iommu_domain always represents some form of translation and the driver is continuously asserting a definable translation mode. It resolves the confusion that the original ops->detach_dev() caused around what translation, exactly, is the IOMMU performing after detach. There were at least three different answers to that question in the tree, they are all now clearly named with domain types. Tested-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Niklas Schnelle <schnelle@linux.ibm.com> Tested-by: Steven Price <steven.price@arm.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Nicolin Chen <nicolinc@nvidia.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> --- drivers/iommu/iommu.c | 22 +++++++--------------- 1 file changed, 7 insertions(+), 15 deletions(-)