| Message ID | 20230921135136.97491-5-macroalpha82@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | [V5,1/4] arm: dts: sun8i: V3s: Add pinctrl for pwm | expand |
在 2023-09-22星期五的 10:31 +0100，Andre Przywara写道： > On Thu, 21 Sep 2023 08:51:36 -0500 > Chris Morgan <macroalpha82@gmail.com> wrote: > > Hi, > > > From: Chris Morgan <macromorgan@hotmail.com> > > > > The Anbernic RG-Nano is a small portable game device based on the > > Allwinner V3s SoC. It has GPIO buttons on the face and side for > > input, a single mono speaker, a 240x240 SPI controlled display, a > > USB-C > > OTG port, an SD card slot for booting, and 64MB of RAM included in > > the > > SoC. There does not appear to be a crystal feeding the internal RTC > > so > > it does not keep proper time (for me it ran 8 hours slow in a 24 > > hour > > period). External RTC works just fine. > > That whole situation is still a bit odd: why is there an external RTC > to > begin with? And did they really save on the 32KHz oscillator, in > favour of > attaching a whole I2C RTC chip? Maybe something is off with the V3 > RTC in > general, and just nobody noticed or cared so far? I think the leakage is a little high, not so suitable for long-time work. > Anyways, I think the DT is fine now, I see all the comments > addressed, and > dtc and dt-validate are happy: > > Reviewed-by: Andre Przywara <andre.przywara@arm.com> > > Cheers, > Andre > > > Working/Tested: > > - SDMMC > > - UART (for debugging) > > - Buttons > > - Charging/battery/PMIC > > - Speaker > > - RTC (external RTC) > > - USB > > - Display > > > > Signed-off-by: Chris Morgan <macromorgan@hotmail.com> > > --- > > arch/arm/boot/dts/allwinner/Makefile | 1 + > > .../allwinner/sun8i-v3s-anbernic-rg-nano.dts | 284 > > ++++++++++++++++++ > > 2 files changed, 285 insertions(+) > > create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic- > > rg-nano.dts > > > > diff --git a/arch/arm/boot/dts/allwinner/Makefile > > b/arch/arm/boot/dts/allwinner/Makefile > > index eebb5a0c873a..2d26c3397f14 100644 > > --- a/arch/arm/boot/dts/allwinner/Makefile > > +++ b/arch/arm/boot/dts/allwinner/Makefile > > @@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ > > sun8i-t113s-mangopi-mq-r-t113.dtb \ > > sun8i-t3-cqa3t-bv3.dtb \ > > sun8i-v3-sl631-imx179.dtb \ > > + sun8i-v3s-anbernic-rg-nano.dtb \ > > sun8i-v3s-licheepi-zero.dtb \ > > sun8i-v3s-licheepi-zero-dock.dtb \ > > sun8i-v40-bananapi-m2-berry.dtb > > diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg- > > nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg- > > nano.dts > > new file mode 100644 > > index 000000000000..1a4429dc57b1 > > --- /dev/null > > +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts > > @@ -0,0 +1,284 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > + > > +/dts-v1/; > > +#include <dt-bindings/input/linux-event-codes.h> > > +#include "sun8i-v3s.dtsi" > > +#include "sunxi-common-regulators.dtsi" > > + > > +/ { > > + model = "Anbernic RG Nano"; > > + compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s"; > > + > > + aliases { > > + rtc0 = &pcf8563; > > + rtc1 = &rtc; > > + serial0 = &uart0; > > + }; > > + > > + backlight: backlight { > > + compatible = "pwm-backlight"; > > + brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 > > 100>; > > + default-brightness-level = <11>; > > + power-supply = <®_vcc5v0>; > > + pwms = <&pwm 0 40000 1>; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + gpio_keys: gpio-keys { > > + compatible = "gpio-keys"; > > + > > + button-a { > > + gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-A"; > > + linux,code = <BTN_EAST>; > > + }; > > + > > + button-b { > > + gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-B"; > > + linux,code = <BTN_SOUTH>; > > + }; > > + > > + button-down { > > + gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "DPAD-DOWN"; > > + linux,code = <BTN_DPAD_DOWN>; > > + }; > > + > > + button-left { > > + gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "DPAD-LEFT"; > > + linux,code = <BTN_DPAD_LEFT>; > > + }; > > + > > + button-right { > > + gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "DPAD-RIGHT"; > > + linux,code = <BTN_DPAD_RIGHT>; > > + }; > > + > > + button-se { > > + gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-SELECT"; > > + linux,code = <BTN_SELECT>; > > + }; > > + > > + button-st { > > + gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-START"; > > + linux,code = <BTN_START>; > > + }; > > + > > + button-tl { > > + gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-L"; > > + linux,code = <BTN_TL>; > > + }; > > + > > + button-tr { > > + gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-R"; > > + linux,code = <BTN_TR>; > > + }; > > + > > + button-up { > > + gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "DPAD-UP"; > > + linux,code = <BTN_DPAD_UP>; > > + }; > > + > > + button-x { > > + gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-X"; > > + linux,code = <BTN_NORTH>; > > + }; > > + > > + button-y { > > + gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW > > | GPIO_PULL_UP)>; > > + label = "BTN-Y"; > > + linux,code = <BTN_WEST>; > > + }; > > + }; > > +}; > > + > > +&codec { > > + allwinner,audio-routing = "Speaker", "HP", > > + "MIC1", "Mic", > > + "Mic", "HBIAS"; > > + allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | > > GPIO_PULL_UP)>; /* PF6 */ > > + status = "okay"; > > +}; > > + > > +&ehci { > > + status = "okay"; > > +}; > > + > > +&i2c0 { > > + status = "okay"; > > + > > + gpio_expander: gpio@20 { > > + compatible = "nxp,pcal6416"; > > + reg = <0x20>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + #interrupt-cells = <2>; > > + interrupt-controller; > > + interrupt-parent = <&pio>; > > + interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 > > */ > > + vcc-supply = <®_vcc3v3>; > > + }; > > + > > + axp209: pmic@34 { > > + reg = <0x34>; > > + interrupt-parent = <&pio>; > > + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* > > PB5/EINT5 */ > > + }; > > + > > + pcf8563: rtc@51 { > > + compatible = "nxp,pcf8563"; > > + reg = <0x51>; > > + }; > > +}; > > + > > +#include "axp209.dtsi" > > + > > +&battery_power_supply { > > + status = "okay"; > > +}; > > + > > +&mmc0 { > > + broken-cd; > > + bus-width = <4>; > > + disable-wp; > > + vmmc-supply = <®_vcc3v3>; > > + vqmmc-supply = <®_vcc3v3>; > > + status = "okay"; > > +}; > > + > > +&ohci { > > + status = "okay"; > > +}; > > + > > +&pio { > > + vcc-pb-supply = <®_vcc3v3>; > > + vcc-pc-supply = <®_vcc3v3>; > > + vcc-pf-supply = <®_vcc3v3>; > > + vcc-pg-supply = <®_vcc3v3>; > > + > > + spi0_no_miso_pins: spi0-no-miso-pins { > > + pins = "PC1", "PC2", "PC3"; > > + function = "spi0"; > > + }; > > +}; > > + > > +&pwm { > > + pinctrl-0 = <&pwm0_pin>; > > + pinctrl-names = "default"; > > + status = "okay"; > > +}; > > + > > +/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */ > > +®_dcdc2 { > > + regulator-always-on; > > + regulator-max-microvolt = <1250000>; > > + regulator-min-microvolt = <1250000>; > > + regulator-name = "vdd-cpu"; > > +}; > > + > > +/* DCDC3 wired into every 3.3v input that isn't the RTC. */ > > +®_dcdc3 { > > + regulator-always-on; > > + regulator-max-microvolt = <3300000>; > > + regulator-min-microvolt = <3300000>; > > + regulator-name = "vcc-io"; > > +}; > > + > > +/* > > + * LDO1 wired into RTC, voltage is hard-wired at 3.3v and cannot > > be > > + * software modified. Note that setting voltage here to 3.3v for > > accuracy > > + * sake causes an issue with the driver that causes it to fail to > > probe > > + * because of a voltage constraint in the driver. > > + */ > > +®_ldo1 { > > + regulator-always-on; > > + regulator-name = "vcc-rtc"; > > +}; > > + > > +/* LDO2 wired into VCC-PLL and audio codec. */ > > +®_ldo2 { > > + regulator-always-on; > > + regulator-max-microvolt = <3000000>; > > + regulator-min-microvolt = <3000000>; > > + regulator-name = "vcc-pll"; > > +}; > > + > > +/* LDO3, LDO4, and LDO5 unused. */ > > +®_ldo3 { > > + status = "disabled"; > > +}; > > + > > +®_ldo4 { > > + status = "disabled"; > > +}; > > + > > +/* > > + * Force the driver to use internal oscillator by removing clocks > > + * property. > > + */ > > +&rtc { > > + /delete-property/ clocks; > > +}; > > + > > +&spi0 { > > + pinctrl-0 = <&spi0_no_miso_pins>; > > + pinctrl-names = "default"; > > + status = "okay"; > > + > > + display@0 { > > + compatible = "saef,sftc154b", "panel-mipi-dbi-spi"; > > + reg = <0>; > > + backlight = <&backlight>; > > + dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */ > > + reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 > > */ > > + spi-max-frequency = <100000000>; > > + > > + height-mm = <39>; > > + width-mm = <39>; > > + > > + /* Set hb-porch to compensate for non-visible area > > */ > > + panel-timing { > > + hactive = <240>; > > + vactive = <240>; > > + hback-porch = <80>; > > + vback-porch = <0>; > > + clock-frequency = <0>; > > + hfront-porch = <0>; > > + hsync-len = <0>; > > + vfront-porch = <0>; > > + vsync-len = <0>; > > + }; > > + }; > > +}; > > + > > +&uart0 { > > + pinctrl-0 = <&uart0_pb_pins>; > > + pinctrl-names = "default"; > > + status = "okay"; > > +}; > > + > > +&usb_otg { > > + dr_mode = "otg"; > > + status = "okay"; > > +}; > > + > > +&usb_power_supply { > > + status = "okay"; > > +}; > > + > > +&usbphy { > > + usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | > > GPIO_PULL_UP)>; /* PG5 */ > > + status = "okay"; > > +}; >
On Sun, Sep 24, 2023 at 09:33:53PM +0200, Jernej Škrabec wrote: > Dne četrtek, 21. september 2023 ob 15:51:36 CEST je Chris Morgan napisal(a): > > From: Chris Morgan <macromorgan@hotmail.com> > > > > The Anbernic RG-Nano is a small portable game device based on the > > Allwinner V3s SoC. It has GPIO buttons on the face and side for > > input, a single mono speaker, a 240x240 SPI controlled display, a USB-C > > OTG port, an SD card slot for booting, and 64MB of RAM included in the > > SoC. There does not appear to be a crystal feeding the internal RTC so > > it does not keep proper time (for me it ran 8 hours slow in a 24 hour > > period). External RTC works just fine. > > > > Working/Tested: > > - SDMMC > > - UART (for debugging) > > - Buttons > > - Charging/battery/PMIC > > - Speaker > > - RTC (external RTC) > > - USB > > - Display > > > > Signed-off-by: Chris Morgan <macromorgan@hotmail.com> > > --- > > arch/arm/boot/dts/allwinner/Makefile | 1 + > > .../allwinner/sun8i-v3s-anbernic-rg-nano.dts | 284 ++++++++++++++++++ > > 2 files changed, 285 insertions(+) > > create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts > > > > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile > > index eebb5a0c873a..2d26c3397f14 100644 > > --- a/arch/arm/boot/dts/allwinner/Makefile > > +++ b/arch/arm/boot/dts/allwinner/Makefile > > @@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ > > sun8i-t113s-mangopi-mq-r-t113.dtb \ > > sun8i-t3-cqa3t-bv3.dtb \ > > sun8i-v3-sl631-imx179.dtb \ > > + sun8i-v3s-anbernic-rg-nano.dtb \ > > sun8i-v3s-licheepi-zero.dtb \ > > sun8i-v3s-licheepi-zero-dock.dtb \ > > sun8i-v40-bananapi-m2-berry.dtb > > diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts > > new file mode 100644 > > index 000000000000..1a4429dc57b1 > > --- /dev/null > > +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts > > @@ -0,0 +1,284 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > + > > +/dts-v1/; > > +#include <dt-bindings/input/linux-event-codes.h> > > +#include "sun8i-v3s.dtsi" > > +#include "sunxi-common-regulators.dtsi" > > + > > +/ { > > + model = "Anbernic RG Nano"; > > + compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s"; > > + > > + aliases { > > + rtc0 = &pcf8563; > > + rtc1 = &rtc; > > + serial0 = &uart0; > > + }; > > + > > + backlight: backlight { > > + compatible = "pwm-backlight"; > > + brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>; > > + default-brightness-level = <11>; > > + power-supply = <®_vcc5v0>; > > + pwms = <&pwm 0 40000 1>; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + gpio_keys: gpio-keys { > > + compatible = "gpio-keys"; > > + > > + button-a { > > + gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-A"; > > + linux,code = <BTN_EAST>; > > + }; > > + > > + button-b { > > + gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-B"; > > + linux,code = <BTN_SOUTH>; > > + }; > > + > > + button-down { > > + gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "DPAD-DOWN"; > > + linux,code = <BTN_DPAD_DOWN>; > > + }; > > + > > + button-left { > > + gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "DPAD-LEFT"; > > + linux,code = <BTN_DPAD_LEFT>; > > + }; > > + > > + button-right { > > + gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "DPAD-RIGHT"; > > + linux,code = <BTN_DPAD_RIGHT>; > > + }; > > + > > + button-se { > > + gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-SELECT"; > > + linux,code = <BTN_SELECT>; > > + }; > > + > > + button-st { > > + gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-START"; > > + linux,code = <BTN_START>; > > + }; > > + > > + button-tl { > > + gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-L"; > > + linux,code = <BTN_TL>; > > + }; > > + > > + button-tr { > > + gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-R"; > > + linux,code = <BTN_TR>; > > + }; > > + > > + button-up { > > + gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "DPAD-UP"; > > + linux,code = <BTN_DPAD_UP>; > > + }; > > + > > + button-x { > > + gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-X"; > > + linux,code = <BTN_NORTH>; > > + }; > > + > > + button-y { > > + gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; > > + label = "BTN-Y"; > > + linux,code = <BTN_WEST>; > > + }; > > + }; > > +}; > > + > > +&codec { > > + allwinner,audio-routing = "Speaker", "HP", > > + "MIC1", "Mic", > > + "Mic", "HBIAS"; > > + allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PF6 */ > > + status = "okay"; > > +}; > > + > > +&ehci { > > + status = "okay"; > > +}; > > + > > +&i2c0 { > > + status = "okay"; > > + > > + gpio_expander: gpio@20 { > > + compatible = "nxp,pcal6416"; > > + reg = <0x20>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + #interrupt-cells = <2>; > > + interrupt-controller; > > + interrupt-parent = <&pio>; > > + interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */ > > + vcc-supply = <®_vcc3v3>; > > + }; > > + > > + axp209: pmic@34 { > > + reg = <0x34>; > > + interrupt-parent = <&pio>; > > + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5 */ > > + }; > > + > > + pcf8563: rtc@51 { > > + compatible = "nxp,pcf8563"; > > + reg = <0x51>; > > + }; > > +}; > > + > > +#include "axp209.dtsi" > > + > > +&battery_power_supply { > > + status = "okay"; > > +}; > > + > > +&mmc0 { > > + broken-cd; > > + bus-width = <4>; > > + disable-wp; > > + vmmc-supply = <®_vcc3v3>; > > + vqmmc-supply = <®_vcc3v3>; > > + status = "okay"; > > +}; > > + > > +&ohci { > > + status = "okay"; > > +}; > > + > > +&pio { > > + vcc-pb-supply = <®_vcc3v3>; > > + vcc-pc-supply = <®_vcc3v3>; > > + vcc-pf-supply = <®_vcc3v3>; > > + vcc-pg-supply = <®_vcc3v3>; > > + > > + spi0_no_miso_pins: spi0-no-miso-pins { > > + pins = "PC1", "PC2", "PC3"; > > + function = "spi0"; > > + }; > > +}; > > + > > +&pwm { > > + pinctrl-0 = <&pwm0_pin>; > > + pinctrl-names = "default"; > > + status = "okay"; > > +}; > > + > > +/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */ > > +®_dcdc2 { > > + regulator-always-on; > > + regulator-max-microvolt = <1250000>; > > + regulator-min-microvolt = <1250000>; > > + regulator-name = "vdd-cpu"; > > +}; > > + > > +/* DCDC3 wired into every 3.3v input that isn't the RTC. */ > > +®_dcdc3 { > > + regulator-always-on; > > + regulator-max-microvolt = <3300000>; > > + regulator-min-microvolt = <3300000>; > > + regulator-name = "vcc-io"; > > +}; > > + > > +/* > > + * LDO1 wired into RTC, voltage is hard-wired at 3.3v and cannot be > > + * software modified. Note that setting voltage here to 3.3v for accuracy > > + * sake causes an issue with the driver that causes it to fail to probe > > + * because of a voltage constraint in the driver. > > + */ > > Can you please remove any mention of drivers everywhere? DT is OS and > thus driver independent. > > Once fixed: > Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> This note was added due to prior comments because in this very specific case we're working around a driver issue. Sadly if I accurately describe the hardware the PMIC and devices that depend on it will fail to probe (the hardware is 3.3v, but here it's set as 1.3v). https://lore.kernel.org/linux-sunxi/20230629203410.660eb9a4@slackpad.lan/ Thank you, Chris > > Best regards, > Jernej > > > +®_ldo1 { > > + regulator-always-on; > > + regulator-name = "vcc-rtc"; > > +}; > > + > > +/* LDO2 wired into VCC-PLL and audio codec. */ > > +®_ldo2 { > > + regulator-always-on; > > + regulator-max-microvolt = <3000000>; > > + regulator-min-microvolt = <3000000>; > > + regulator-name = "vcc-pll"; > > +}; > > + > > +/* LDO3, LDO4, and LDO5 unused. */ > > +®_ldo3 { > > + status = "disabled"; > > +}; > > + > > +®_ldo4 { > > + status = "disabled"; > > +}; > > + > > +/* > > + * Force the driver to use internal oscillator by removing clocks > > + * property. > > + */ > > +&rtc { > > + /delete-property/ clocks; > > +}; > > + > > +&spi0 { > > + pinctrl-0 = <&spi0_no_miso_pins>; > > + pinctrl-names = "default"; > > + status = "okay"; > > + > > + display@0 { > > + compatible = "saef,sftc154b", "panel-mipi-dbi-spi"; > > + reg = <0>; > > + backlight = <&backlight>; > > + dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */ > > + reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ > > + spi-max-frequency = <100000000>; > > + > > + height-mm = <39>; > > + width-mm = <39>; > > + > > + /* Set hb-porch to compensate for non-visible area */ > > + panel-timing { > > + hactive = <240>; > > + vactive = <240>; > > + hback-porch = <80>; > > + vback-porch = <0>; > > + clock-frequency = <0>; > > + hfront-porch = <0>; > > + hsync-len = <0>; > > + vfront-porch = <0>; > > + vsync-len = <0>; > > + }; > > + }; > > +}; > > + > > +&uart0 { > > + pinctrl-0 = <&uart0_pb_pins>; > > + pinctrl-names = "default"; > > + status = "okay"; > > +}; > > + > > +&usb_otg { > > + dr_mode = "otg"; > > + status = "okay"; > > +}; > > + > > +&usb_power_supply { > > + status = "okay"; > > +}; > > + > > +&usbphy { > > + usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG5 */ > > + status = "okay"; > > +}; > > > > > >
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile index eebb5a0c873a..2d26c3397f14 100644 --- a/arch/arm/boot/dts/allwinner/Makefile +++ b/arch/arm/boot/dts/allwinner/Makefile @@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-t113s-mangopi-mq-r-t113.dtb \ sun8i-t3-cqa3t-bv3.dtb \ sun8i-v3-sl631-imx179.dtb \ + sun8i-v3s-anbernic-rg-nano.dtb \ sun8i-v3s-licheepi-zero.dtb \ sun8i-v3s-licheepi-zero-dock.dtb \ sun8i-v40-bananapi-m2-berry.dtb diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts new file mode 100644 index 000000000000..1a4429dc57b1 --- /dev/null +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include <dt-bindings/input/linux-event-codes.h> +#include "sun8i-v3s.dtsi" +#include "sunxi-common-regulators.dtsi" + +/ { + model = "Anbernic RG Nano"; + compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s"; + + aliases { + rtc0 = &pcf8563; + rtc1 = &rtc; + serial0 = &uart0; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>; + default-brightness-level = <11>; + power-supply = <®_vcc5v0>; + pwms = <&pwm 0 40000 1>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + + button-a { + gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-A"; + linux,code = <BTN_EAST>; + }; + + button-b { + gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-B"; + linux,code = <BTN_SOUTH>; + }; + + button-down { + gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "DPAD-DOWN"; + linux,code = <BTN_DPAD_DOWN>; + }; + + button-left { + gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "DPAD-LEFT"; + linux,code = <BTN_DPAD_LEFT>; + }; + + button-right { + gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "DPAD-RIGHT"; + linux,code = <BTN_DPAD_RIGHT>; + }; + + button-se { + gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-SELECT"; + linux,code = <BTN_SELECT>; + }; + + button-st { + gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-START"; + linux,code = <BTN_START>; + }; + + button-tl { + gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-L"; + linux,code = <BTN_TL>; + }; + + button-tr { + gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-R"; + linux,code = <BTN_TR>; + }; + + button-up { + gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "DPAD-UP"; + linux,code = <BTN_DPAD_UP>; + }; + + button-x { + gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-X"; + linux,code = <BTN_NORTH>; + }; + + button-y { + gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + label = "BTN-Y"; + linux,code = <BTN_WEST>; + }; + }; +}; + +&codec { + allwinner,audio-routing = "Speaker", "HP", + "MIC1", "Mic", + "Mic", "HBIAS"; + allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PF6 */ + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + gpio_expander: gpio@20 { + compatible = "nxp,pcal6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + #interrupt-cells = <2>; + interrupt-controller; + interrupt-parent = <&pio>; + interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */ + vcc-supply = <®_vcc3v3>; + }; + + axp209: pmic@34 { + reg = <0x34>; + interrupt-parent = <&pio>; + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5 */ + }; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +#include "axp209.dtsi" + +&battery_power_supply { + status = "okay"; +}; + +&mmc0 { + broken-cd; + bus-width = <4>; + disable-wp; + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc3v3>; + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&pio { + vcc-pb-supply = <®_vcc3v3>; + vcc-pc-supply = <®_vcc3v3>; + vcc-pf-supply = <®_vcc3v3>; + vcc-pg-supply = <®_vcc3v3>; + + spi0_no_miso_pins: spi0-no-miso-pins { + pins = "PC1", "PC2", "PC3"; + function = "spi0"; + }; +}; + +&pwm { + pinctrl-0 = <&pwm0_pin>; + pinctrl-names = "default"; + status = "okay"; +}; + +/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */ +®_dcdc2 { + regulator-always-on; + regulator-max-microvolt = <1250000>; + regulator-min-microvolt = <1250000>; + regulator-name = "vdd-cpu"; +}; + +/* DCDC3 wired into every 3.3v input that isn't the RTC. */ +®_dcdc3 { + regulator-always-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "vcc-io"; +}; + +/* + * LDO1 wired into RTC, voltage is hard-wired at 3.3v and cannot be + * software modified. Note that setting voltage here to 3.3v for accuracy + * sake causes an issue with the driver that causes it to fail to probe + * because of a voltage constraint in the driver. + */ +®_ldo1 { + regulator-always-on; + regulator-name = "vcc-rtc"; +}; + +/* LDO2 wired into VCC-PLL and audio codec. */ +®_ldo2 { + regulator-always-on; + regulator-max-microvolt = <3000000>; + regulator-min-microvolt = <3000000>; + regulator-name = "vcc-pll"; +}; + +/* LDO3, LDO4, and LDO5 unused. */ +®_ldo3 { + status = "disabled"; +}; + +®_ldo4 { + status = "disabled"; +}; + +/* + * Force the driver to use internal oscillator by removing clocks + * property. + */ +&rtc { + /delete-property/ clocks; +}; + +&spi0 { + pinctrl-0 = <&spi0_no_miso_pins>; + pinctrl-names = "default"; + status = "okay"; + + display@0 { + compatible = "saef,sftc154b", "panel-mipi-dbi-spi"; + reg = <0>; + backlight = <&backlight>; + dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */ + reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ + spi-max-frequency = <100000000>; + + height-mm = <39>; + width-mm = <39>; + + /* Set hb-porch to compensate for non-visible area */ + panel-timing { + hactive = <240>; + vactive = <240>; + hback-porch = <80>; + vback-porch = <0>; + clock-frequency = <0>; + hfront-porch = <0>; + hsync-len = <0>; + vfront-porch = <0>; + vsync-len = <0>; + }; + }; +}; + +&uart0 { + pinctrl-0 = <&uart0_pb_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG5 */ + status = "okay"; +};