| Message ID | 20230621043628.21485-4-quic_kriskura@quicinc.com |
|---|---|
| State | New |
| Headers | show |
| Series | Add multiport support for DWC3 controllers | expand |
On Wed, Jun 21, 2023, Krishna Kurapati wrote: > Currently host-only capable DWC3 controllers support Multiport. > Temporarily map XHCI address space for host-only controllers and parse > XHCI Extended Capabilities registers to read number of usb2 ports and > usb3 ports present on multiport controller. Each USB Port is at least HS > capable. > > The port info for usb2 and usb3 phy are identified as num_usb2_ports > and num_usb3_ports. The intention is as follows: > > Wherever we need to perform phy operations like: > > LOOP_OVER_NUMBER_OF_AVAILABLE_PORTS() > { > phy_set_mode(dwc->usb2_generic_phy[i], PHY_MODE_USB_HOST); > phy_set_mode(dwc->usb3_generic_phy[i], PHY_MODE_USB_HOST); > } > > If number of usb2 ports is 3, loop can go from index 0-2 for > usb2_generic_phy. If number of usb3-ports is 2, we don't know for sure, > if the first 2 ports are SS capable or some other ports like (2 and 3) > are SS capable. So instead, num_usb2_ports is used to loop around all > phy's (both hs and ss) for performing phy operations. If any > usb3_generic_phy turns out to be NULL, phy operation just bails out. > > num_usb3_ports is used to modify GUSB3PIPECTL registers while setting up > phy's as we need to know how many SS capable ports are there for this. > > Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > --- > drivers/usb/dwc3/core.c | 62 +++++++++++++++++++++++++++++++++++++++++ > drivers/usb/dwc3/core.h | 9 ++++++ > 2 files changed, 71 insertions(+) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index f6689b731718..32ec05fc242b 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -39,6 +39,7 @@ > #include "io.h" > > #include "debug.h" > +#include "../host/xhci-ext-caps.h" > > #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ > > @@ -1767,6 +1768,52 @@ static int dwc3_get_clocks(struct dwc3 *dwc) > return 0; > } > > +static int dwc3_read_port_info(struct dwc3 *dwc) > +{ > + void __iomem *base; > + u8 major_revision; > + u32 offset = 0; > + int ret = 0; > + u32 val; > + > + /* > + * Remap xHCI address space to access XHCI ext cap regs, > + * since it is needed to get port info. > + */ > + base = ioremap(dwc->xhci_resources[0].start, > + resource_size(&dwc->xhci_resources[0])); > + if (IS_ERR(base)) > + return PTR_ERR(base); > + > + do { > + offset = xhci_find_next_ext_cap(base, offset, > + XHCI_EXT_CAPS_PROTOCOL); > + > + if (!offset) > + break; > + > + val = readl(base + offset); > + major_revision = XHCI_EXT_PORT_MAJOR(val); > + > + val = readl(base + offset + 0x08); > + if (major_revision == 0x03) { > + dwc->num_usb3_ports += XHCI_EXT_PORT_COUNT(val); > + } else if (major_revision <= 0x02) { > + dwc->num_usb2_ports += XHCI_EXT_PORT_COUNT(val); > + } else { > + dev_err(dwc->dev, > + "Unrecognized port major revision %d\n", > + major_revision); > + } > + } while (1); > + > + dev_dbg(dwc->dev, "hs-ports: %u ss-ports: %u\n", > + dwc->num_usb2_ports, dwc->num_usb3_ports); > + > + iounmap(base); > + return ret; > +} > + > static int dwc3_probe(struct platform_device *pdev) > { > struct device *dev = &pdev->dev; > @@ -1774,6 +1821,7 @@ static int dwc3_probe(struct platform_device *pdev) > void __iomem *regs; > struct dwc3 *dwc; > int ret; > + unsigned int hw_mode; > > dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL); > if (!dwc) > @@ -1854,6 +1902,20 @@ static int dwc3_probe(struct platform_device *pdev) > goto err_disable_clks; > } > > + /* > + * Currently only DWC3 controllers that are host-only capable > + * support Multiport. > + */ > + hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); > + if (hw_mode == DWC3_GHWPARAMS0_MODE_HOST) { > + ret = dwc3_read_port_info(dwc); > + if (ret) > + goto err_disable_clks; > + } else { > + dwc->num_usb2_ports = 1; > + dwc->num_usb3_ports = 1; > + } > + > spin_lock_init(&dwc->lock); > mutex_init(&dwc->mutex); > > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index 8b1295e4dcdd..42fb17aa66fa 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -33,6 +33,10 @@ > > #include <linux/power_supply.h> > > +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) > +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) > +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) > + > #define DWC3_MSG_MAX 500 > > /* Global constants */ > @@ -1029,6 +1033,8 @@ struct dwc3_scratchpad_array { > * @usb3_phy: pointer to USB3 PHY > * @usb2_generic_phy: pointer to USB2 PHY > * @usb3_generic_phy: pointer to USB3 PHY > + * @num_usb2_ports: number of USB2 ports. > + * @num_usb3_ports: number of USB3 ports. > * @phys_ready: flag to indicate that PHYs are ready > * @ulpi: pointer to ulpi interface > * @ulpi_ready: flag to indicate that ULPI is initialized > @@ -1168,6 +1174,9 @@ struct dwc3 { > struct phy *usb2_generic_phy; > struct phy *usb3_generic_phy; > > + u8 num_usb2_ports; > + u8 num_usb3_ports; > + > bool phys_ready; > > struct ulpi *ulpi; > -- > 2.40.0 > Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Thanks, Thinh
On Wed, Jun 21, 2023 at 10:06:21AM +0530, Krishna Kurapati wrote: > Currently host-only capable DWC3 controllers support Multiport. > Temporarily map XHCI address space for host-only controllers and parse > XHCI Extended Capabilities registers to read number of usb2 ports and > usb3 ports present on multiport controller. Each USB Port is at least HS > capable. > > The port info for usb2 and usb3 phy are identified as num_usb2_ports > and num_usb3_ports. The intention is as follows: > > Wherever we need to perform phy operations like: > > LOOP_OVER_NUMBER_OF_AVAILABLE_PORTS() > { > phy_set_mode(dwc->usb2_generic_phy[i], PHY_MODE_USB_HOST); > phy_set_mode(dwc->usb3_generic_phy[i], PHY_MODE_USB_HOST); > } > > If number of usb2 ports is 3, loop can go from index 0-2 for > usb2_generic_phy. If number of usb3-ports is 2, we don't know for sure, > if the first 2 ports are SS capable or some other ports like (2 and 3) > are SS capable. So instead, num_usb2_ports is used to loop around all > phy's (both hs and ss) for performing phy operations. If any > usb3_generic_phy turns out to be NULL, phy operation just bails out. > > num_usb3_ports is used to modify GUSB3PIPECTL registers while setting up > phy's as we need to know how many SS capable ports are there for this. > > Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > --- > drivers/usb/dwc3/core.c | 62 +++++++++++++++++++++++++++++++++++++++++ > drivers/usb/dwc3/core.h | 9 ++++++ > 2 files changed, 71 insertions(+) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index f6689b731718..32ec05fc242b 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -39,6 +39,7 @@ > #include "io.h" > > #include "debug.h" > +#include "../host/xhci-ext-caps.h" > > #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ > > @@ -1767,6 +1768,52 @@ static int dwc3_get_clocks(struct dwc3 *dwc) > return 0; > } > > +static int dwc3_read_port_info(struct dwc3 *dwc) > +{ > + void __iomem *base; > + u8 major_revision; > + u32 offset = 0; > + int ret = 0; ret is never modified, so drop and return 0 unconditionally below. You can add it back later in the series when you start using it. > + u32 val; > + > + /* > + * Remap xHCI address space to access XHCI ext cap regs, > + * since it is needed to get port info. > + */ > + base = ioremap(dwc->xhci_resources[0].start, > + resource_size(&dwc->xhci_resources[0])); > + if (IS_ERR(base)) > + return PTR_ERR(base); > + > + do { > + offset = xhci_find_next_ext_cap(base, offset, > + XHCI_EXT_CAPS_PROTOCOL); > + You can drop this newline. > + if (!offset) > + break; > + > + val = readl(base + offset); > + major_revision = XHCI_EXT_PORT_MAJOR(val); > + > + val = readl(base + offset + 0x08); > + if (major_revision == 0x03) { > + dwc->num_usb3_ports += XHCI_EXT_PORT_COUNT(val); > + } else if (major_revision <= 0x02) { > + dwc->num_usb2_ports += XHCI_EXT_PORT_COUNT(val); > + } else { > + dev_err(dwc->dev, > + "Unrecognized port major revision %d\n", > + major_revision); > + } > + } while (1); > + > + dev_dbg(dwc->dev, "hs-ports: %u ss-ports: %u\n", > + dwc->num_usb2_ports, dwc->num_usb3_ports); > + > + iounmap(base); Nit: I'd add a newline here. > + return ret; > +} > + > static int dwc3_probe(struct platform_device *pdev) > { > struct device *dev = &pdev->dev; > @@ -1774,6 +1821,7 @@ static int dwc3_probe(struct platform_device *pdev) > void __iomem *regs; > struct dwc3 *dwc; > int ret; > + unsigned int hw_mode; > > dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL); > if (!dwc) > @@ -1854,6 +1902,20 @@ static int dwc3_probe(struct platform_device *pdev) > goto err_disable_clks; > } > > + /* > + * Currently only DWC3 controllers that are host-only capable > + * support Multiport. > + */ > + hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); > + if (hw_mode == DWC3_GHWPARAMS0_MODE_HOST) { > + ret = dwc3_read_port_info(dwc); > + if (ret) > + goto err_disable_clks; > + } else { > + dwc->num_usb2_ports = 1; > + dwc->num_usb3_ports = 1; > + } > + > spin_lock_init(&dwc->lock); > mutex_init(&dwc->mutex); > > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index 8b1295e4dcdd..42fb17aa66fa 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -33,6 +33,10 @@ > > #include <linux/power_supply.h> > > +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) > +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) > +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) Again, don't copy defines from xhci. Looks like these should be moved to the xhci-ext-caps.h header along with struct xhci_protocol_caps. > + > #define DWC3_MSG_MAX 500 > > /* Global constants */ > @@ -1029,6 +1033,8 @@ struct dwc3_scratchpad_array { > * @usb3_phy: pointer to USB3 PHY > * @usb2_generic_phy: pointer to USB2 PHY > * @usb3_generic_phy: pointer to USB3 PHY > + * @num_usb2_ports: number of USB2 ports. > + * @num_usb3_ports: number of USB3 ports. Again, please drop the full stops ('.'). Johan
Hi Krishna, Please remember to trim unnecessary context from your replies (e.g. as it makes it easier to read your reply and later the entire thread in the mailing list archives). On Mon, Jul 03, 2023 at 12:18:14AM +0530, Krishna Kurapati PSSNV wrote: > On 6/27/2023 5:15 PM, Johan Hovold wrote: > > On Wed, Jun 21, 2023 at 10:06:21AM +0530, Krishna Kurapati wrote: > >> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > >> index 8b1295e4dcdd..42fb17aa66fa 100644 > >> --- a/drivers/usb/dwc3/core.h > >> +++ b/drivers/usb/dwc3/core.h > >> @@ -33,6 +33,10 @@ > >> > >> #include <linux/power_supply.h> > >> > >> +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) > >> +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) > >> +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) > > > > Again, don't copy defines from xhci. > > > > Looks like these should be moved to the xhci-ext-caps.h header along > > with struct xhci_protocol_caps. > > > Can't we just give them an exception ? Modifying xhci stuff doesn't > sound good. Can I just rename them and keep them here ? Nope. This is mainline, not Qualcomm's vendor kernel. Johan
On 6/27/2023 5:15 PM, Johan Hovold wrote: > On Wed, Jun 21, 2023 at 10:06:21AM +0530, Krishna Kurapati wrote: >> Currently host-only capable DWC3 controllers support Multiport. >> Temporarily map XHCI address space for host-only controllers and parse >> XHCI Extended Capabilities registers to read number of usb2 ports and >> usb3 ports present on multiport controller. Each USB Port is at least HS >> capable. >> >> The port info for usb2 and usb3 phy are identified as num_usb2_ports >> and num_usb3_ports. The intention is as follows: >> >> Wherever we need to perform phy operations like: >> >> LOOP_OVER_NUMBER_OF_AVAILABLE_PORTS() >> { >> phy_set_mode(dwc->usb2_generic_phy[i], PHY_MODE_USB_HOST); >> phy_set_mode(dwc->usb3_generic_phy[i], PHY_MODE_USB_HOST); >> } >> >> If number of usb2 ports is 3, loop can go from index 0-2 for >> usb2_generic_phy. If number of usb3-ports is 2, we don't know for sure, >> if the first 2 ports are SS capable or some other ports like (2 and 3) >> are SS capable. So instead, num_usb2_ports is used to loop around all >> phy's (both hs and ss) for performing phy operations. If any >> usb3_generic_phy turns out to be NULL, phy operation just bails out. >> >> num_usb3_ports is used to modify GUSB3PIPECTL registers while setting up >> phy's as we need to know how many SS capable ports are there for this. >> >> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> >> --- >> drivers/usb/dwc3/core.c | 62 +++++++++++++++++++++++++++++++++++++++++ >> drivers/usb/dwc3/core.h | 9 ++++++ >> 2 files changed, 71 insertions(+) >> >> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c >> index f6689b731718..32ec05fc242b 100644 >> --- a/drivers/usb/dwc3/core.c >> +++ b/drivers/usb/dwc3/core.c >> @@ -39,6 +39,7 @@ >> #include "io.h" >> >> #include "debug.h" >> +#include "../host/xhci-ext-caps.h" >> >> #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ >> >> @@ -1767,6 +1768,52 @@ static int dwc3_get_clocks(struct dwc3 *dwc) >> return 0; >> } >> >> +static int dwc3_read_port_info(struct dwc3 *dwc) >> +{ >> + void __iomem *base; >> + u8 major_revision; >> + u32 offset = 0; >> + int ret = 0; > > ret is never modified, so drop and return 0 unconditionally below. > > You can add it back later in the series when you start using it. > >> + u32 val; >> + >> + /* >> + * Remap xHCI address space to access XHCI ext cap regs, >> + * since it is needed to get port info. >> + */ >> + base = ioremap(dwc->xhci_resources[0].start, >> + resource_size(&dwc->xhci_resources[0])); >> + if (IS_ERR(base)) >> + return PTR_ERR(base); >> + >> + do { >> + offset = xhci_find_next_ext_cap(base, offset, >> + XHCI_EXT_CAPS_PROTOCOL); >> + > > You can drop this newline. > >> + if (!offset) >> + break; >> + >> + val = readl(base + offset); >> + major_revision = XHCI_EXT_PORT_MAJOR(val); >> + >> + val = readl(base + offset + 0x08); >> + if (major_revision == 0x03) { >> + dwc->num_usb3_ports += XHCI_EXT_PORT_COUNT(val); >> + } else if (major_revision <= 0x02) { >> + dwc->num_usb2_ports += XHCI_EXT_PORT_COUNT(val); >> + } else { >> + dev_err(dwc->dev, >> + "Unrecognized port major revision %d\n", >> + major_revision); >> + } >> + } while (1); >> + >> + dev_dbg(dwc->dev, "hs-ports: %u ss-ports: %u\n", >> + dwc->num_usb2_ports, dwc->num_usb3_ports); >> + >> + iounmap(base); > > Nit: I'd add a newline here. > >> + return ret; >> +} >> + >> static int dwc3_probe(struct platform_device *pdev) >> { >> struct device *dev = &pdev->dev; >> @@ -1774,6 +1821,7 @@ static int dwc3_probe(struct platform_device *pdev) >> void __iomem *regs; >> struct dwc3 *dwc; >> int ret; >> + unsigned int hw_mode; >> >> dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL); >> if (!dwc) >> @@ -1854,6 +1902,20 @@ static int dwc3_probe(struct platform_device *pdev) >> goto err_disable_clks; >> } >> >> + /* >> + * Currently only DWC3 controllers that are host-only capable >> + * support Multiport. >> + */ >> + hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); >> + if (hw_mode == DWC3_GHWPARAMS0_MODE_HOST) { >> + ret = dwc3_read_port_info(dwc); >> + if (ret) >> + goto err_disable_clks; >> + } else { >> + dwc->num_usb2_ports = 1; >> + dwc->num_usb3_ports = 1; >> + } >> + >> spin_lock_init(&dwc->lock); >> mutex_init(&dwc->mutex); >> >> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h >> index 8b1295e4dcdd..42fb17aa66fa 100644 >> --- a/drivers/usb/dwc3/core.h >> +++ b/drivers/usb/dwc3/core.h >> @@ -33,6 +33,10 @@ >> >> #include <linux/power_supply.h> >> >> +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) >> +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) >> +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) > > Again, don't copy defines from xhci. > > Looks like these should be moved to the xhci-ext-caps.h header along > with struct xhci_protocol_caps. > Hi Johan, Moving the defines would be sufficient right ? Just wanted to know if there is any reason you are suggesting to move the structure as well so that I can update commit text accordingly. Regards, Krishna, >> + >> #define DWC3_MSG_MAX 500 >> >> /* Global constants */ >> @@ -1029,6 +1033,8 @@ struct dwc3_scratchpad_array { >> * @usb3_phy: pointer to USB3 PHY >> * @usb2_generic_phy: pointer to USB2 PHY >> * @usb3_generic_phy: pointer to USB3 PHY >> + * @num_usb2_ports: number of USB2 ports. >> + * @num_usb3_ports: number of USB3 ports. > > Again, please drop the full stops ('.'). > > Johan
[ Please remember to trim your replies. ] On Sun, Jul 23, 2023 at 08:29:47PM +0530, Krishna Kurapati PSSNV wrote: > On 6/27/2023 5:15 PM, Johan Hovold wrote: > > On Wed, Jun 21, 2023 at 10:06:21AM +0530, Krishna Kurapati wrote: > >> +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) > >> +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) > >> +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) > > > > Again, don't copy defines from xhci. > > > > Looks like these should be moved to the xhci-ext-caps.h header along > > with struct xhci_protocol_caps. > > Moving the defines would be sufficient right ? Just wanted to know if > there is any reason you are suggesting to move the structure as well so > that I can update commit text accordingly. The defines are used for parsing the members of struct xhci_protocol_caps and they belong together even if no driver has apparently ever used the structure. Johan
On 7/24/2023 9:11 PM, Johan Hovold wrote: > [ Please remember to trim your replies. ] > > On Sun, Jul 23, 2023 at 08:29:47PM +0530, Krishna Kurapati PSSNV wrote: >> On 6/27/2023 5:15 PM, Johan Hovold wrote: >>> On Wed, Jun 21, 2023 at 10:06:21AM +0530, Krishna Kurapati wrote: > >>>> +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) >>>> +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) >>>> +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) >>> >>> Again, don't copy defines from xhci. >>> >>> Looks like these should be moved to the xhci-ext-caps.h header along >>> with struct xhci_protocol_caps. >> >> Moving the defines would be sufficient right ? Just wanted to know if >> there is any reason you are suggesting to move the structure as well so >> that I can update commit text accordingly. > > The defines are used for parsing the members of struct > xhci_protocol_caps and they belong together even if no driver has > apparently ever used the structure. Hi Johan, Thanks for the suggestions. Will push out v10 today. Regards, Krishna,
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index f6689b731718..32ec05fc242b 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -39,6 +39,7 @@ #include "io.h" #include "debug.h" +#include "../host/xhci-ext-caps.h" #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ @@ -1767,6 +1768,52 @@ static int dwc3_get_clocks(struct dwc3 *dwc) return 0; } +static int dwc3_read_port_info(struct dwc3 *dwc) +{ + void __iomem *base; + u8 major_revision; + u32 offset = 0; + int ret = 0; + u32 val; + + /* + * Remap xHCI address space to access XHCI ext cap regs, + * since it is needed to get port info. + */ + base = ioremap(dwc->xhci_resources[0].start, + resource_size(&dwc->xhci_resources[0])); + if (IS_ERR(base)) + return PTR_ERR(base); + + do { + offset = xhci_find_next_ext_cap(base, offset, + XHCI_EXT_CAPS_PROTOCOL); + + if (!offset) + break; + + val = readl(base + offset); + major_revision = XHCI_EXT_PORT_MAJOR(val); + + val = readl(base + offset + 0x08); + if (major_revision == 0x03) { + dwc->num_usb3_ports += XHCI_EXT_PORT_COUNT(val); + } else if (major_revision <= 0x02) { + dwc->num_usb2_ports += XHCI_EXT_PORT_COUNT(val); + } else { + dev_err(dwc->dev, + "Unrecognized port major revision %d\n", + major_revision); + } + } while (1); + + dev_dbg(dwc->dev, "hs-ports: %u ss-ports: %u\n", + dwc->num_usb2_ports, dwc->num_usb3_ports); + + iounmap(base); + return ret; +} + static int dwc3_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -1774,6 +1821,7 @@ static int dwc3_probe(struct platform_device *pdev) void __iomem *regs; struct dwc3 *dwc; int ret; + unsigned int hw_mode; dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL); if (!dwc) @@ -1854,6 +1902,20 @@ static int dwc3_probe(struct platform_device *pdev) goto err_disable_clks; } + /* + * Currently only DWC3 controllers that are host-only capable + * support Multiport. + */ + hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); + if (hw_mode == DWC3_GHWPARAMS0_MODE_HOST) { + ret = dwc3_read_port_info(dwc); + if (ret) + goto err_disable_clks; + } else { + dwc->num_usb2_ports = 1; + dwc->num_usb3_ports = 1; + } + spin_lock_init(&dwc->lock); mutex_init(&dwc->mutex); diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 8b1295e4dcdd..42fb17aa66fa 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -33,6 +33,10 @@ #include <linux/power_supply.h> +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) +#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff) +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) + #define DWC3_MSG_MAX 500 /* Global constants */ @@ -1029,6 +1033,8 @@ struct dwc3_scratchpad_array { * @usb3_phy: pointer to USB3 PHY * @usb2_generic_phy: pointer to USB2 PHY * @usb3_generic_phy: pointer to USB3 PHY + * @num_usb2_ports: number of USB2 ports. + * @num_usb3_ports: number of USB3 ports. * @phys_ready: flag to indicate that PHYs are ready * @ulpi: pointer to ulpi interface * @ulpi_ready: flag to indicate that ULPI is initialized @@ -1168,6 +1174,9 @@ struct dwc3 { struct phy *usb2_generic_phy; struct phy *usb3_generic_phy; + u8 num_usb2_ports; + u8 num_usb3_ports; + bool phys_ready; struct ulpi *ulpi;
Currently host-only capable DWC3 controllers support Multiport. Temporarily map XHCI address space for host-only controllers and parse XHCI Extended Capabilities registers to read number of usb2 ports and usb3 ports present on multiport controller. Each USB Port is at least HS capable. The port info for usb2 and usb3 phy are identified as num_usb2_ports and num_usb3_ports. The intention is as follows: Wherever we need to perform phy operations like: LOOP_OVER_NUMBER_OF_AVAILABLE_PORTS() { phy_set_mode(dwc->usb2_generic_phy[i], PHY_MODE_USB_HOST); phy_set_mode(dwc->usb3_generic_phy[i], PHY_MODE_USB_HOST); } If number of usb2 ports is 3, loop can go from index 0-2 for usb2_generic_phy. If number of usb3-ports is 2, we don't know for sure, if the first 2 ports are SS capable or some other ports like (2 and 3) are SS capable. So instead, num_usb2_ports is used to loop around all phy's (both hs and ss) for performing phy operations. If any usb3_generic_phy turns out to be NULL, phy operation just bails out. num_usb3_ports is used to modify GUSB3PIPECTL registers while setting up phy's as we need to know how many SS capable ports are there for this. Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> --- drivers/usb/dwc3/core.c | 62 +++++++++++++++++++++++++++++++++++++++++ drivers/usb/dwc3/core.h | 9 ++++++ 2 files changed, 71 insertions(+)