| Message ID | 20230725-bq_m5-v2-2-9779c249aeb1@apitzsch.eu |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: msm8939-longcheer-l9100: Add initial dts | expand |
Am Dienstag, dem 25.07.2023 um 22:05 +0200 schrieb André Apitzsch: > This dts adds support for BQ Aquaris M5 (Longcheer L9100) released in > 2015. > > Add a device tree with initial support for: > > - GPIO keys > - Hall sensor > - SDHCI > - WCNSS (BT/WIFI) > - Accelerometer/Magnetometer > - Vibrator > - Touchscreen > - Front flash > > Signed-off-by: André Apitzsch <git@apitzsch.eu> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8939-longcheer-l9100.dts | 336 > +++++++++++++++++++++ > 2 files changed, 337 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile > b/arch/arm64/boot/dts/qcom/Makefile > index 23fd31d4bf5a..3200bc92853f 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -39,6 +39,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc- > uf896.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-yiming-uz801v3.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8939-longcheer-l9100.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8939-samsung-a7.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8939-sony-xperia-kanuti- > tulip.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts > b/arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts > new file mode 100644 > index 000000000000..d8e37bdb4916 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts > @@ -0,0 +1,336 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8939-pm8916.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> > + > +/ { > + model = "BQ Aquaris M5 (Longcheer L9100)"; > + compatible = "longcheer,l9100", "qcom,msm8939"; > + chassis-type = "handset"; > + > + aliases { > + mmc0 = &sdhc_1; /* eMMC */ > + mmc1 = &sdhc_2; /* SD card */ > + serial0 = &blsp_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + gpio-hall-sensor { > + compatible = "gpio-keys"; > + > + pinctrl-0 = <&gpio_hall_sensor_default>; > + pinctrl-names = "default"; > + > + label = "GPIO Hall Effect Sensor"; > + > + event-hall-sensor { > + label = "Hall Effect Sensor"; > + gpios = <&tlmm 20 GPIO_ACTIVE_LOW>; > + linux,input-type = <EV_SW>; > + linux,code = <SW_LID>; > + linux,can-disable; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-0 = <&gpio_keys_default>; > + pinctrl-names = "default"; > + > + label = "GPIO Buttons"; > + > + button-volume-up { > + label = "Volume Up"; > + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-0 { > + gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>; > + color = <LED_COLOR_ID_WHITE>; > + default-state = "off"; > + function = LED_FUNCTION_KBD_BACKLIGHT; > + > + pinctrl-0 = <&button_backlight_default>; > + pinctrl-names = "default"; > + }; > + }; > + > + reg_ts_vdd: regulator-vdd-ts { > + compatible = "regulator-fixed"; > + regulator-name = "regulator-vdd-ts"; > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + > + gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + pinctrl-0 = <&ts_vdd_default>; > + pinctrl-names = "default"; > + }; > + > + backlight { > + compatible = "pwm-backlight"; > + pwms = <&pm8916_pwm 0 100000>; > + brightness-levels = <0 255>; > + num-interpolated-steps = <255>; > + default-brightness-level = <128>; > + enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&lcd_bl_en_default>; > + pinctrl-names = "default"; > + }; > + > + flash-led-controller { > + compatible = "ocs,ocp8110"; > + flash-gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>; > + enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&camera_front_flash_default>; > + pinctrl-names = "default"; > + > + led { > + function = LED_FUNCTION_FLASH; > + color = <LED_COLOR_ID_WHITE>; > + flash-max-timeout-us = <250000>; > + }; > + }; > + > + usb_id: usb-id { > + compatible = "linux,extcon-usb-gpio"; > + id-gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>; I just noticed, that I forgot to include the `id-gpios` change mentioned in the changelog of v2. Will send a v3 later including this change. But waiting for further feedback first. André > + pinctrl-0 = <&usb_id_default &usb_id_switch_default>; > + pinctrl-names = "default"; > + }; > + > +}; > + > +&blsp_i2c3 { > + status = "okay"; > + > + magnetometer@d { > + compatible = "asahi-kasei,ak09911"; > + reg = <0x0d>; > + > + vdd-supply = <&pm8916_l17>; > + vid-supply = <&pm8916_l6>; > + > + reset-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&mag_reset_default>; > + pinctrl-names = "default"; > + }; > + > + light-sensor@23 { > + compatible = "liteon,ltr559"; > + reg = <0x23>; > + > + vdd-supply = <&pm8916_l17>; > + vddio-supply = <&pm8916_l5>; > + > + interrupt-parent = <&tlmm>; > + interrupts = <113 IRQ_TYPE_EDGE_FALLING>; > + > + pinctrl-0 = <&light_int_default>; > + pinctrl-names = "default"; > + }; > + > + imu@68 { > + compatible = "bosch,bmi160"; > + reg = <0x68>; > + > + vdd-supply = <&pm8916_l17>; > + vddio-supply = <&pm8916_l6>; > + }; > +}; > + > +&blsp_i2c5 { > + status = "okay"; > + > + touchscreen@4a { > + compatible = "atmel,maxtouch"; > + reg = <0x4a>; > + > + interrupt-parent = <&tlmm>; > + interrupts = <13 IRQ_TYPE_LEVEL_LOW>; > + > + reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; > + > + vdda-supply = <&pm8916_l6>; > + vdd-supply = <®_ts_vdd>; > + > + pinctrl-0 = <&ts_int_reset_default>; > + pinctrl-names = "default"; > + > + /* Keys listed from right to left */ > + linux,keycodes = <KEY_APPSELECT KEY_HOMEPAGE > KEY_BACK>; > + }; > +}; > + > +&blsp_uart2 { > + status = "okay"; > +}; > + > +&pm8916_mpps { > + pwm_out: mpp4-state { > + pins = "mpp4"; > + function = "digital"; > + power-source = <PM8916_MPP_VPH>; > + output-low; > + qcom,dtest = <1>; > + }; > +}; > + > +&pm8916_pwm { > + pinctrl-0 = <&pwm_out>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&pm8916_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&pm8916_rpm_regulators { > + pm8916_l17: l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > +}; > + > +&pm8916_vib { > + status = "okay"; > +}; > + > +&sdhc_1 { > + status = "okay"; > +}; > + > +&sdhc_2 { > + pinctrl-0 = <&sdc2_default &sdc2_cd_default>; > + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; > + pinctrl-names = "default", "sleep"; > + > + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; > + > + status = "okay"; > +}; > + > +&usb { > + extcon = <&usb_id>, <&usb_id>; > + status = "okay"; > +}; > + > +&usb_hs_phy { > + extcon = <&usb_id>; > +}; > + > +&wcnss { > + status = "okay"; > +}; > + > +&wcnss_iris { > + compatible = "qcom,wcn3620"; > +}; > + > +&tlmm { > + button_backlight_default: button-backlight-default-state { > + pins = "gpio17"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + camera_front_flash_default: camera-front-flash-default-state > { > + pins = "gpio8", "gpio49"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + gpio_hall_sensor_default: gpio-hall-sensor-default-state { > + pins = "gpio20"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + gpio_keys_default: gpio-keys-default-state { > + pins = "gpio107"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + lcd_bl_en_default: lcd-bl-en-default-state { > + pins = "gpio98"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + light_int_default: light-int-default-state { > + pins = "gpio113"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + mag_reset_default: mag-reset-default-state { > + pins = "gpio68"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + sdc2_cd_default: sdc2-cd-default-state { > + pins = "gpio38"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + ts_int_reset_default: ts-int-reset-default-state { > + pins = "gpio12", "gpio13"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + ts_vdd_default: ts-vdd-default-state { > + pins = "gpio78"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + usb_id_default: usb-id-default-state { > + pins = "gpio110"; > + function = "gpio"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + usb_id_switch_default: usb-id-switch-default-state { > + pins = "gpio121"; > + function = "gpio"; > + drive-strength = <2>; > + output-high; > + }; > +}; >
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 23fd31d4bf5a..3200bc92853f 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -39,6 +39,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-yiming-uz801v3.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8939-longcheer-l9100.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8939-samsung-a7.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8939-sony-xperia-kanuti-tulip.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts b/arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts new file mode 100644 index 000000000000..d8e37bdb4916 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts @@ -0,0 +1,336 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8939-pm8916.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +/ { + model = "BQ Aquaris M5 (Longcheer L9100)"; + compatible = "longcheer,l9100", "qcom,msm8939"; + chassis-type = "handset"; + + aliases { + mmc0 = &sdhc_1; /* eMMC */ + mmc1 = &sdhc_2; /* SD card */ + serial0 = &blsp_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + + pinctrl-0 = <&gpio_hall_sensor_default>; + pinctrl-names = "default"; + + label = "GPIO Hall Effect Sensor"; + + event-hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 20 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&gpio_keys_default>; + pinctrl-names = "default"; + + label = "GPIO Buttons"; + + button-volume-up { + label = "Volume Up"; + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_WHITE>; + default-state = "off"; + function = LED_FUNCTION_KBD_BACKLIGHT; + + pinctrl-0 = <&button_backlight_default>; + pinctrl-names = "default"; + }; + }; + + reg_ts_vdd: regulator-vdd-ts { + compatible = "regulator-fixed"; + regulator-name = "regulator-vdd-ts"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + + gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&ts_vdd_default>; + pinctrl-names = "default"; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pm8916_pwm 0 100000>; + brightness-levels = <0 255>; + num-interpolated-steps = <255>; + default-brightness-level = <128>; + enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&lcd_bl_en_default>; + pinctrl-names = "default"; + }; + + flash-led-controller { + compatible = "ocs,ocp8110"; + flash-gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>; + enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&camera_front_flash_default>; + pinctrl-names = "default"; + + led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + flash-max-timeout-us = <250000>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb_id_default &usb_id_switch_default>; + pinctrl-names = "default"; + }; + +}; + +&blsp_i2c3 { + status = "okay"; + + magnetometer@d { + compatible = "asahi-kasei,ak09911"; + reg = <0x0d>; + + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + + reset-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&mag_reset_default>; + pinctrl-names = "default"; + }; + + light-sensor@23 { + compatible = "liteon,ltr559"; + reg = <0x23>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + + interrupt-parent = <&tlmm>; + interrupts = <113 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-0 = <&light_int_default>; + pinctrl-names = "default"; + }; + + imu@68 { + compatible = "bosch,bmi160"; + reg = <0x68>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + }; +}; + +&blsp_i2c5 { + status = "okay"; + + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + + interrupt-parent = <&tlmm>; + interrupts = <13 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + vdda-supply = <&pm8916_l6>; + vdd-supply = <®_ts_vdd>; + + pinctrl-0 = <&ts_int_reset_default>; + pinctrl-names = "default"; + + /* Keys listed from right to left */ + linux,keycodes = <KEY_APPSELECT KEY_HOMEPAGE KEY_BACK>; + }; +}; + +&blsp_uart2 { + status = "okay"; +}; + +&pm8916_mpps { + pwm_out: mpp4-state { + pins = "mpp4"; + function = "digital"; + power-source = <PM8916_MPP_VPH>; + output-low; + qcom,dtest = <1>; + }; +}; + +&pm8916_pwm { + pinctrl-0 = <&pwm_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&pm8916_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&pm8916_rpm_regulators { + pm8916_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; +}; + +&pm8916_vib { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_default &sdc2_cd_default>; + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; + pinctrl-names = "default", "sleep"; + + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + + status = "okay"; +}; + +&usb { + extcon = <&usb_id>, <&usb_id>; + status = "okay"; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&wcnss { + status = "okay"; +}; + +&wcnss_iris { + compatible = "qcom,wcn3620"; +}; + +&tlmm { + button_backlight_default: button-backlight-default-state { + pins = "gpio17"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + camera_front_flash_default: camera-front-flash-default-state { + pins = "gpio8", "gpio49"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + gpio_hall_sensor_default: gpio-hall-sensor-default-state { + pins = "gpio20"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default-state { + pins = "gpio107"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + lcd_bl_en_default: lcd-bl-en-default-state { + pins = "gpio98"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + light_int_default: light-int-default-state { + pins = "gpio113"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + mag_reset_default: mag-reset-default-state { + pins = "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + sdc2_cd_default: sdc2-cd-default-state { + pins = "gpio38"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + ts_int_reset_default: ts-int-reset-default-state { + pins = "gpio12", "gpio13"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + ts_vdd_default: ts-vdd-default-state { + pins = "gpio78"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb_id_default: usb-id-default-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + usb_id_switch_default: usb-id-switch-default-state { + pins = "gpio121"; + function = "gpio"; + drive-strength = <2>; + output-high; + }; +};
This dts adds support for BQ Aquaris M5 (Longcheer L9100) released in 2015. Add a device tree with initial support for: - GPIO keys - Hall sensor - SDHCI - WCNSS (BT/WIFI) - Accelerometer/Magnetometer - Vibrator - Touchscreen - Front flash Signed-off-by: André Apitzsch <git@apitzsch.eu> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8939-longcheer-l9100.dts | 336 +++++++++++++++++++++ 2 files changed, 337 insertions(+)