diff mbox series

[2/2] arm64: dts: freescale: Add imx8mp-venice-gw7905-2x

Message ID 20230511171041.4011087-2-tharvey@gateworks.com
State New
Headers show
Series [1/2] dt-bindings: arm: Add Gateworks i.MX8M GW7905-2x board | expand

Commit Message

Tim Harvey May 11, 2023, 5:10 p.m. UTC
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.

The GW702x SOM contains the following:
 - i.MX8M Plus SoC
 - LPDDR4 memory
 - eMMC Boot device
 - Gateworks System Controller (GSC) with integrated EEPROM, button
   controller, and ADC's
 - PMIC
 - RGMII PHY (eQoS)
 - SOM connector providing:
  - eQoS GbE MII
  - 1x SPI
  - 2x I2C
  - 4x UART
  - 2x USB 3.0
  - 1x PCI
  - 1x SDIO (4-bit 3.3V)
  - 1x SDIO (4-bit 3.3V/1.8V)
  - GPIO

The GW7905 Baseboard contains the following:
 - GPS
 - microSD
 - off-board I/O connector with I2C, SPI, GPIO
 - EERPOM
 - PCIe clock generator
 - 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
 - 1x half-length miniPCIe socket with USB2.0 and USB3.0
 - USB 3.0 HUB
 - USB Type-C with USB PD Sink capability and peripheral support
 - USB Type-C with USB 3.0 host support

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
 .../dts/freescale/imx8mp-venice-gw702x.dtsi   | 589 ++++++++++++++++++
 .../dts/freescale/imx8mp-venice-gw7905-2x.dts |  28 +
 .../dts/freescale/imx8mp-venice-gw7905.dtsi   | 358 +++++++++++
 3 files changed, 975 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi

Comments

Krzysztof Kozlowski May 11, 2023, 5:23 p.m. UTC | #1
On 11/05/2023 19:10, Tim Harvey wrote:
> The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
> 
> The GW702x SOM contains the following:
>  - i.MX8M Plus SoC
>  - LPDDR4 memory
>  - eMMC Boot device
>  - Gateworks System Controller (GSC) with integrated EEPROM, button
>    controller, and ADC's
>  - PMIC
>  - RGMII PHY (eQoS)
>  - SOM connector providing:
>   - eQoS GbE MII
>   - 1x SPI
>   - 2x I2C
>   - 4x UART
>   - 2x USB 3.0
>   - 1x PCI
>   - 1x SDIO (4-bit 3.3V)
>   - 1x SDIO (4-bit 3.3V/1.8V)
>   - GPIO
> 
> The GW7905 Baseboard contains the following:
>  - GPS
>  - microSD
>  - off-board I/O connector with I2C, SPI, GPIO
>  - EERPOM
>  - PCIe clock generator
>  - 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
>  - 1x half-length miniPCIe socket with USB2.0 and USB3.0
>  - USB 3.0 HUB
>  - USB Type-C with USB PD Sink capability and peripheral support
>  - USB Type-C with USB 3.0 host support
> 
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---
>  .../dts/freescale/imx8mp-venice-gw702x.dtsi   | 589 ++++++++++++++++++
>  .../dts/freescale/imx8mp-venice-gw7905-2x.dts |  28 +
>  .../dts/freescale/imx8mp-venice-gw7905.dtsi   | 358 +++++++++++


How do you compile it? Missing Makefile. This also suggests that maybe
you did not test it with dtbs_check...


>  3 files changed, 975 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi

...

> +	gsc: gsc@20 {
> +		compatible = "gw,gsc";
> +		reg = <0x20>;
> +		pinctrl-0 = <&pinctrl_gsc>;
> +		interrupt-parent = <&gpio2>;
> +		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		adc {
> +			compatible = "gw,gsc-adc";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			channel@6 {
> +				gw,mode = <0>;
> +				reg = <0x06>;
> +				label = "temp";
> +			};
> +
> +			channel@8 {
> +				gw,mode = <1>;
> +				reg = <0x08>;
> +				label = "vdd_bat";
> +			};
> +
> +			channel@16 {
> +				gw,mode = <4>;
> +				reg = <0x16>;
> +				label = "fan_tach";
> +			};
> +
> +			channel@82 {
> +				gw,mode = <2>;
> +				reg = <0x82>;
> +				label = "vdd_vin";
> +				gw,voltage-divider-ohms = <22100 1000>;
> +			};
> +
> +			channel@84 {
> +				gw,mode = <2>;
> +				reg = <0x84>;
> +				label = "vdd_adc1";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@86 {
> +				gw,mode = <2>;
> +				reg = <0x86>;
> +				label = "vdd_adc2";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@88 {
> +				gw,mode = <2>;
> +				reg = <0x88>;
> +				label = "vdd_1p0";
> +			};
> +
> +			channel@8c {
> +				gw,mode = <2>;
> +				reg = <0x8c>;
> +				label = "vdd_1p8";
> +			};
> +
> +			channel@8e {
> +				gw,mode = <2>;
> +				reg = <0x8e>;
> +				label = "vdd_2p5";
> +			};
> +
> +			channel@90 {
> +				gw,mode = <2>;
> +				reg = <0x90>;
> +				label = "vdd_3p3";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +
> +			channel@92 {
> +				gw,mode = <2>;
> +				reg = <0x92>;
> +				label = "vdd_dram";
> +			};
> +
> +			channel@98 {
> +				gw,mode = <2>;
> +				reg = <0x98>;
> +				label = "vdd_soc";
> +			};
> +
> +			channel@9a {
> +				gw,mode = <2>;
> +				reg = <0x9a>;
> +				label = "vdd_arm";
> +			};
> +
> +			channel@a2 {
> +				gw,mode = <2>;
> +				reg = <0xa2>;
> +				label = "vdd_gsc";
> +				gw,voltage-divider-ohms = <10000 10000>;
> +			};
> +		};
> +
> +		fan-controller@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;

Why do you need these two? I know binding expects them, but why? Anyway
compatible is first, reg is second property.


> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> new file mode 100644
> index 000000000000..4a1bbbbe19e6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
> @@ -0,0 +1,28 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Gateworks Corporation
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp.dtsi"
> +#include "imx8mp-venice-gw702x.dtsi"
> +#include "imx8mp-venice-gw7905.dtsi"
> +
> +/ {
> +	model = "Gateworks Venice GW7905-2x i.MX8MP Development Kit";
> +	compatible = "gateworks,imx8mp-gw7905-2x", "fsl,imx8mp";
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +};
> +
> +/* Disable SOM interfaces not used on baseboard */
> +&eqos {
> +	status = "disabled";
> +};
> +
> +&usdhc1 {
> +	status = "disabled";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
> new file mode 100644
> index 000000000000..479190a6391f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
> @@ -0,0 +1,358 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Gateworks Corporation
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +
> +/ {
> +	aliases {
> +		ethernet0 = &eqos;
> +	};
> +
> +	led-controller {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		led-0 {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		led-1 {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_RED>;
> +			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	pcie0_refclk: pcie0-refclk {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <100000000>;
> +	};
> +
> +	pps {
> +		compatible = "pps-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pps>;
> +		gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> +		status = "okay";
> +	};
> +
> +	reg_usb2_vbus: regulator-usb2-vbus {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usb2_en>;
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb2_vbus";
> +		gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-usdhc2 {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		compatible = "regulator-fixed";
> +		regulator-name = "SD2_3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +

Drop stay blank line

> +};
> +
> +/* off-board header */
> +&ecspi2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi2>;
> +	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};



Best regards,
Krzysztof
Krzysztof Kozlowski May 12, 2023, 4:13 p.m. UTC | #2
On 12/05/2023 17:07, Tim Harvey wrote:
> On Thu, May 11, 2023 at 10:23 AM Krzysztof Kozlowski
> <krzysztof.kozlowski@linaro.org> wrote:

> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi b/arch/arm6
> 4/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
> index 4fca4aae8f72..74b0fda235ed 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
> @@ -222,8 +222,6 @@ channel@a2 {
>                 };
> 
>                 fan-controller@0 {
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
>                         compatible = "gw,gsc-fan";
>                         reg = <0x0a>;
>                 };
> 
> Would that make sense?
> 
> Is it that the fan-controller because it does not have addressable
> child nodes does not need address-cells?

I just looked a bit and requirement of address/size cells seemed odd.
There are no children, it's not a bus etc, so yes, drop it.


Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
new file mode 100644
index 000000000000..4fca4aae8f72
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw702x.dtsi
@@ -0,0 +1,589 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	aliases {
+		ethernet0 = &eqos;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-user-pb {
+			label = "user_pb";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		key-user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key_erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		key-eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		key-tamper {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck3_reg>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck3_reg>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck3_reg>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck3_reg>;
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reg = <0x0>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		pinctrl-0 = <&pinctrl_gsc>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@6 {
+				gw,mode = <0>;
+				reg = <0x06>;
+				label = "temp";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@16 {
+				gw,mode = <4>;
+				reg = <0x16>;
+				label = "fan_tach";
+			};
+
+			channel@82 {
+				gw,mode = <2>;
+				reg = <0x82>;
+				label = "vdd_vin";
+				gw,voltage-divider-ohms = <22100 1000>;
+			};
+
+			channel@84 {
+				gw,mode = <2>;
+				reg = <0x84>;
+				label = "vdd_adc1";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@86 {
+				gw,mode = <2>;
+				reg = <0x86>;
+				label = "vdd_adc2";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@88 {
+				gw,mode = <2>;
+				reg = <0x88>;
+				label = "vdd_1p0";
+			};
+
+			channel@8c {
+				gw,mode = <2>;
+				reg = <0x8c>;
+				label = "vdd_1p8";
+			};
+
+			channel@8e {
+				gw,mode = <2>;
+				reg = <0x8e>;
+				label = "vdd_2p5";
+			};
+
+			channel@90 {
+				gw,mode = <2>;
+				reg = <0x90>;
+				label = "vdd_3p3";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@92 {
+				gw,mode = <2>;
+				reg = <0x92>;
+				label = "vdd_dram";
+			};
+
+			channel@98 {
+				gw,mode = <2>;
+				reg = <0x98>;
+				label = "vdd_soc";
+			};
+
+			channel@9a {
+				gw,mode = <2>;
+				reg = <0x9a>;
+				label = "vdd_arm";
+			};
+
+			channel@a2 {
+				gw,mode = <2>;
+				reg = <0xa2>;
+				label = "vdd_gsc";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+		};
+
+		fan-controller@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "gw,gsc-fan";
+			reg = <0x0a>;
+		};
+	};
+
+	gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+
+	pmic@69 {
+		compatible = "mps,mp5416";
+		reg = <0x69>;
+
+		regulators {
+			/* vdd_soc */
+			buck1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* vdd_dram */
+			buck2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* vdd_arm */
+			buck3_reg: buck3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* vdd_1p8 */
+			buck4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* OUT2: nvcc_snvs_1p8 */
+			ldo1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* OUT3: vdd_1p0 */
+			ldo2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* OUT4: vdd_2p5 */
+			ldo3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* OUT5: vdd_3p3 */
+			ldo4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+/* off-board header */
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c32";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+/* off-board header */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+/* off-board header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* off-board header */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* off-board */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC			0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO			0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0		0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1		0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2		0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3		0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0		0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1		0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2		0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3		0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
+		>;
+	};
+
+	pinctrl_ethphy0: ethphy0grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14	0x140 /* RST# */
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x150 /* IRQ# */
+		>;
+	};
+
+	pinctrl_gsc: gscgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06	0x150 /* IRQ# */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14	0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15	0x400001c2
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x400001c2
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18	0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19	0x400001c2
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x140
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX	0x140
+			MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x190
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d0
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d0
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d0
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d0
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0x166
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
new file mode 100644
index 000000000000..4a1bbbbe19e6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905-2x.dts
@@ -0,0 +1,28 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx8mp.dtsi"
+#include "imx8mp-venice-gw702x.dtsi"
+#include "imx8mp-venice-gw7905.dtsi"
+
+/ {
+	model = "Gateworks Venice GW7905-2x i.MX8MP Development Kit";
+	compatible = "gateworks,imx8mp-gw7905-2x", "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+/* Disable SOM interfaces not used on baseboard */
+&eqos {
+	status = "disabled";
+};
+
+&usdhc1 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
new file mode 100644
index 000000000000..479190a6391f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw7905.dtsi
@@ -0,0 +1,358 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+/ {
+	aliases {
+		ethernet0 = &eqos;
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	pps {
+		compatible = "pps-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pps>;
+		gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_en>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_vbus";
+		gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		compatible = "regulator-fixed";
+		regulator-name = "SD2_3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+};
+
+/* off-board header */
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "gpioa", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "gpiod", "", "",
+		"gpiob", "gpioc", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"som_3p3en", "", "pci_usbsel", "",
+		"pci_wdis#", "", "", "";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c32";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+/* off-board header */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+		 <&clk IMX8MP_CLK_PCIE_ROOT>,
+		 <&clk IMX8MP_CLK_HSIO_AXI>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
+	assigned-clock-rates = <10000000>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
+	status = "okay";
+};
+
+/* GPS */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* USB1 - Type C front panel SINK port J14 */
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+/* USB2 4-port USB3.0 HUB:
+ *  P1 - USBC connector (host only)
+ *  P2 - USB2 test connector
+ *  P3 - miniPCIe full card
+ *  P4 - miniPCIe half card
+ *  GPIO4_IO12 is USBHUB_RST# which has an ext p/u
+ */
+&usb3_phy1 {
+	vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
+
+&usb3_1 {
+	fsl,permanently-attached;
+	fsl,disable-port-power-control;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* microSD */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13	0x40000040 /* GPIOA */
+			MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01	0x40000040 /* GPIOD */
+			MX8MP_IOMUXC_SAI1_RXD2__GPIO4_IO04	0x40000040 /* GPIOB */
+			MX8MP_IOMUXC_SAI1_RXD3__GPIO4_IO05	0x40000040 /* GPIOC */
+			MX8MP_IOMUXC_SAI2_TXD0__GPIO4_IO26	0x40000106 /* PCI_USBSEL */
+			MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28	0x40000106 /* PCI_WDIS# */
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22	0x18	/* LEDG */
+			MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27	0x18	/* LEDR */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_pcie0: pciegrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29	0x110
+		>;
+	};
+
+	pinctrl_pps: ppsgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21	0x41
+		>;
+	};
+
+	pinctrl_reg_usb2_en: regusb2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_TXD0__GPIO4_IO12	0x40000146 /* USBHUB_RST# (ext p/u) */
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
+		>;
+	};
+
+	pinctrl_spi2: spi2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK	0x82
+			MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI	0x82
+			MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO	0x82
+			MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13	0x140
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x140
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x190
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d0
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d0
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d0
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d0
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d0
+			MX8MP_IOMUXC_GPIO1_IO03__USDHC1_VSELECT	0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x194
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d4
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d4
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d4
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d4
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d4
+			MX8MP_IOMUXC_GPIO1_IO03__USDHC1_VSELECT	0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x196
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d6
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d6
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d6
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d6
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d6
+			MX8MP_IOMUXC_GPIO1_IO03__USDHC1_VSELECT	0xc1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc0
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x80
+		>;
+	};
+};