| Message ID | 20230505064039.1630025-4-bhupesh.sharma@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | Add Qualcomm SM6115 / SM4250 EUD dt-bindings & driver support | expand |
On Fri, 5 May 2023 at 14:05, Konrad Dybcio <konrad.dybcio@linaro.org> wrote: > > > > On 5.05.2023 08:40, Bhupesh Sharma wrote: > > Add SM6115 / SM4250 SoC EUD support in qcom_eud driver. > > > > On some SoCs (like the SM6115 / SM4250 SoC), the mode manager > > needs to be accessed only via the secure world (through 'scm' > > calls). > > > > Also, the enable bit inside 'tcsr_check_reg' needs to be set > > first to set the eud in 'enable' mode on these SoCs. > > > > Since this difference comes from how the firmware is configured, so > > the driver now relies on the presence of an extra boolean DT property > > to identify if secure access is needed. > > > > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> > > --- > > drivers/usb/misc/Kconfig | 1 + > > drivers/usb/misc/qcom_eud.c | 74 +++++++++++++++++++++++++++++++++---- > > 2 files changed, 68 insertions(+), 7 deletions(-) > > > > diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig > > index 99b15b77dfd5..fe1b5fec1dfc 100644 > > --- a/drivers/usb/misc/Kconfig > > +++ b/drivers/usb/misc/Kconfig > > @@ -147,6 +147,7 @@ config USB_APPLEDISPLAY > > config USB_QCOM_EUD > > tristate "QCOM Embedded USB Debugger(EUD) Driver" > > depends on ARCH_QCOM || COMPILE_TEST > > + select QCOM_SCM > > select USB_ROLE_SWITCH > > help > > This module enables support for Qualcomm Technologies, Inc. > > diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c > > index b7f13df00764..18a2dee3b4b9 100644 > > --- a/drivers/usb/misc/qcom_eud.c > > +++ b/drivers/usb/misc/qcom_eud.c > > @@ -5,12 +5,14 @@ > > > > #include <linux/bitops.h> > > #include <linux/err.h> > > +#include <linux/firmware/qcom/qcom_scm.h> > > #include <linux/interrupt.h> > > #include <linux/io.h> > > #include <linux/iopoll.h> > > #include <linux/kernel.h> > > #include <linux/module.h> > > #include <linux/of.h> > > +#include <linux/of_device.h> > > #include <linux/platform_device.h> > > #include <linux/slab.h> > > #include <linux/sysfs.h> > > @@ -22,23 +24,35 @@ > > #define EUD_REG_VBUS_INT_CLR 0x0080 > > #define EUD_REG_CSR_EUD_EN 0x1014 > > #define EUD_REG_SW_ATTACH_DET 0x1018 > > -#define EUD_REG_EUD_EN2 0x0000 > > +#define EUD_REG_EUD_EN2 0x0000 > > > > #define EUD_ENABLE BIT(0) > > -#define EUD_INT_PET_EUD BIT(0) > > +#define EUD_INT_PET_EUD BIT(0) > > #define EUD_INT_VBUS BIT(2) > > #define EUD_INT_SAFE_MODE BIT(4) > > #define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE) > > > > +#define EUD_EN2_SECURE_EN BIT(0) > > +#define EUD_EN2_NONSECURE_EN (1) > BIT(0) == 1, is that actually a separate register or does it just > reflect whether scm_writel is used? > > If the latter, perhaps it'd be okay to just call it EUD_EN2_EN or > something along those lines? Isn't that perhaps what the docs call it? > > > > +#define EUD_EN2_DISABLE (0) > > +#define TCSR_CHECK_EN BIT(0) > > + > > +struct eud_soc_cfg { > > + u32 tcsr_check_offset; > > +}; > > + > > struct eud_chip { > > struct device *dev; > > struct usb_role_switch *role_sw; > > + const struct eud_soc_cfg *eud_cfg; > > void __iomem *base; > > void __iomem *mode_mgr; > > unsigned int int_status; > > int irq; > > bool enabled; > > bool usb_attached; > > + bool secure_mode_enable; > Since it's only used in the probe function now, we can get rid > of it! > > > + phys_addr_t secure_mode_mgr; > > }; > > > > static int enable_eud(struct eud_chip *priv) > > @@ -46,7 +60,11 @@ static int enable_eud(struct eud_chip *priv) > > writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN); > > writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE, > > priv->base + EUD_REG_INT1_EN_MASK); > > - writel(1, priv->mode_mgr + EUD_REG_EUD_EN2); > > + > > + if (priv->secure_mode_mgr) > > + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_SECURE_EN); > > + else > > + writel(EUD_EN2_NONSECURE_EN, priv->mode_mgr + EUD_REG_EUD_EN2); > > > > return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE); > > } > > @@ -54,7 +72,11 @@ static int enable_eud(struct eud_chip *priv) > > static void disable_eud(struct eud_chip *priv) > > { > > writel(0, priv->base + EUD_REG_CSR_EUD_EN); > > - writel(0, priv->mode_mgr + EUD_REG_EUD_EN2); > > + > > + if (priv->secure_mode_mgr) > > + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE); > > + else > > + writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2); > > } > > > > static ssize_t enable_show(struct device *dev, > > @@ -178,6 +200,8 @@ static void eud_role_switch_release(void *data) > > static int eud_probe(struct platform_device *pdev) > > { > > struct eud_chip *chip; > > + struct resource *res; > > + phys_addr_t tcsr_base, tcsr_check; > > int ret; > > > > chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); > > @@ -200,9 +224,40 @@ static int eud_probe(struct platform_device *pdev) > > if (IS_ERR(chip->base)) > > return PTR_ERR(chip->base); > > > > - chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); > > - if (IS_ERR(chip->mode_mgr)) > > - return PTR_ERR(chip->mode_mgr); > > + chip->secure_mode_enable = of_property_read_bool(chip->dev->of_node, > > + "qcom,secure-mode-enable"); > > + /* > > + * EUD block on a few Qualcomm SoCs need secure register access. > > + * Check for the same. > > + */ > > + if (chip->secure_mode_enable) { > if (of_property_read_bool...) > > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); > > + if (!res) > > + return dev_err_probe(chip->dev, -ENODEV, > > + "failed to get secure_mode_mgr reg base\n"); > > + > > + chip->secure_mode_mgr = res->start; > > + } else { > > + chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); > > + if (IS_ERR(chip->mode_mgr)) > > + return PTR_ERR(chip->mode_mgr); > > + } > > + > > + /* Check for any SoC specific config data */ > > + chip->eud_cfg = of_device_get_match_data(&pdev->dev); > > + if (chip->eud_cfg) { > > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "tcsr-base"); > > + if (!res) > > + return dev_err_probe(chip->dev, -ENODEV, > > + "failed to get tcsr reg base\n"); > > + > > + tcsr_base = res->start; > This variable does not seem very useful, we can get rid of it. > > > + tcsr_check = tcsr_base + chip->eud_cfg->tcsr_check_offset; > > + > > + ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); > > + if (ret) > > + return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n"); > > + } > > > > chip->irq = platform_get_irq(pdev, 0); > > ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq, > > @@ -230,8 +285,13 @@ static int eud_remove(struct platform_device *pdev) > > return 0; > > } > > > > +static const struct eud_soc_cfg sm6115_eud_cfg = { > This could be marked __initconst, but I'm not sure if future > additions won't need to be accessed after the driver has already > gone through its probe function.. Your call! Please no. The device can be probed later or reprobed, etc. We had __devinit* for this kind of data/functions, but it was removed around 3.x as the HOTPLUG also got removed. > > > Konrad > > + .tcsr_check_offset = 0x25018, > > +}; > > + > > static const struct of_device_id eud_dt_match[] = { > > { .compatible = "qcom,sc7280-eud" }, > > + { .compatible = "qcom,sm6115-eud", .data = &sm6115_eud_cfg }, > > { } > > }; > > MODULE_DEVICE_TABLE(of, eud_dt_match);
On 5.05.2023 17:50, Bhupesh Sharma wrote: > On Fri, 5 May 2023 at 16:35, Konrad Dybcio <konrad.dybcio@linaro.org> wrote: >> >> On 5.05.2023 08:40, Bhupesh Sharma wrote: >>> Add SM6115 / SM4250 SoC EUD support in qcom_eud driver. >>> >>> On some SoCs (like the SM6115 / SM4250 SoC), the mode manager >>> needs to be accessed only via the secure world (through 'scm' >>> calls). >>> >>> Also, the enable bit inside 'tcsr_check_reg' needs to be set >>> first to set the eud in 'enable' mode on these SoCs. >>> >>> Since this difference comes from how the firmware is configured, so >>> the driver now relies on the presence of an extra boolean DT property >>> to identify if secure access is needed. >>> >>> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> >>> --- >>> drivers/usb/misc/Kconfig | 1 + >>> drivers/usb/misc/qcom_eud.c | 74 +++++++++++++++++++++++++++++++++---- >>> 2 files changed, 68 insertions(+), 7 deletions(-) >>> >>> diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig >>> index 99b15b77dfd5..fe1b5fec1dfc 100644 >>> --- a/drivers/usb/misc/Kconfig >>> +++ b/drivers/usb/misc/Kconfig >>> @@ -147,6 +147,7 @@ config USB_APPLEDISPLAY >>> config USB_QCOM_EUD >>> tristate "QCOM Embedded USB Debugger(EUD) Driver" >>> depends on ARCH_QCOM || COMPILE_TEST >>> + select QCOM_SCM >>> select USB_ROLE_SWITCH >>> help >>> This module enables support for Qualcomm Technologies, Inc. >>> diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c >>> index b7f13df00764..18a2dee3b4b9 100644 >>> --- a/drivers/usb/misc/qcom_eud.c >>> +++ b/drivers/usb/misc/qcom_eud.c >>> @@ -5,12 +5,14 @@ >>> >>> #include <linux/bitops.h> >>> #include <linux/err.h> >>> +#include <linux/firmware/qcom/qcom_scm.h> >>> #include <linux/interrupt.h> >>> #include <linux/io.h> >>> #include <linux/iopoll.h> >>> #include <linux/kernel.h> >>> #include <linux/module.h> >>> #include <linux/of.h> >>> +#include <linux/of_device.h> >>> #include <linux/platform_device.h> >>> #include <linux/slab.h> >>> #include <linux/sysfs.h> >>> @@ -22,23 +24,35 @@ >>> #define EUD_REG_VBUS_INT_CLR 0x0080 >>> #define EUD_REG_CSR_EUD_EN 0x1014 >>> #define EUD_REG_SW_ATTACH_DET 0x1018 >>> -#define EUD_REG_EUD_EN2 0x0000 >>> +#define EUD_REG_EUD_EN2 0x0000 >>> >>> #define EUD_ENABLE BIT(0) >>> -#define EUD_INT_PET_EUD BIT(0) >>> +#define EUD_INT_PET_EUD BIT(0) >>> #define EUD_INT_VBUS BIT(2) >>> #define EUD_INT_SAFE_MODE BIT(4) >>> #define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE) >>> >>> +#define EUD_EN2_SECURE_EN BIT(0) >>> +#define EUD_EN2_NONSECURE_EN (1) >> BIT(0) == 1, is that actually a separate register or does it just >> reflect whether scm_writel is used? >> >> If the latter, perhaps it'd be okay to just call it EUD_EN2_EN or >> something along those lines? Isn't that perhaps what the docs call it? > > Ok, let's name it as EUD_EN2_ENABLE then. > >>> +#define EUD_EN2_DISABLE (0) >>> +#define TCSR_CHECK_EN BIT(0) >>> + >>> +struct eud_soc_cfg { >>> + u32 tcsr_check_offset; >>> +}; >>> + >>> struct eud_chip { >>> struct device *dev; >>> struct usb_role_switch *role_sw; >>> + const struct eud_soc_cfg *eud_cfg; >>> void __iomem *base; >>> void __iomem *mode_mgr; >>> unsigned int int_status; >>> int irq; >>> bool enabled; >>> bool usb_attached; >>> + bool secure_mode_enable; >> Since it's only used in the probe function now, we can get rid >> of it! > > Ok. > >>> + phys_addr_t secure_mode_mgr; >>> }; >>> >>> static int enable_eud(struct eud_chip *priv) >>> @@ -46,7 +60,11 @@ static int enable_eud(struct eud_chip *priv) >>> writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN); >>> writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE, >>> priv->base + EUD_REG_INT1_EN_MASK); >>> - writel(1, priv->mode_mgr + EUD_REG_EUD_EN2); >>> + >>> + if (priv->secure_mode_mgr) >>> + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_SECURE_EN); >>> + else >>> + writel(EUD_EN2_NONSECURE_EN, priv->mode_mgr + EUD_REG_EUD_EN2); >>> >>> return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE); >>> } >>> @@ -54,7 +72,11 @@ static int enable_eud(struct eud_chip *priv) >>> static void disable_eud(struct eud_chip *priv) >>> { >>> writel(0, priv->base + EUD_REG_CSR_EUD_EN); >>> - writel(0, priv->mode_mgr + EUD_REG_EUD_EN2); >>> + >>> + if (priv->secure_mode_mgr) >>> + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE); >>> + else >>> + writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2); >>> } >>> >>> static ssize_t enable_show(struct device *dev, >>> @@ -178,6 +200,8 @@ static void eud_role_switch_release(void *data) >>> static int eud_probe(struct platform_device *pdev) >>> { >>> struct eud_chip *chip; >>> + struct resource *res; >>> + phys_addr_t tcsr_base, tcsr_check; >>> int ret; >>> >>> chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); >>> @@ -200,9 +224,40 @@ static int eud_probe(struct platform_device *pdev) >>> if (IS_ERR(chip->base)) >>> return PTR_ERR(chip->base); >>> >>> - chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); >>> - if (IS_ERR(chip->mode_mgr)) >>> - return PTR_ERR(chip->mode_mgr); >>> + chip->secure_mode_enable = of_property_read_bool(chip->dev->of_node, >>> + "qcom,secure-mode-enable"); >>> + /* >>> + * EUD block on a few Qualcomm SoCs need secure register access. >>> + * Check for the same. >>> + */ >>> + if (chip->secure_mode_enable) { >> if (of_property_read_bool...) > > Sure. > >>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); >>> + if (!res) >>> + return dev_err_probe(chip->dev, -ENODEV, >>> + "failed to get secure_mode_mgr reg base\n"); >>> + >>> + chip->secure_mode_mgr = res->start; >>> + } else { >>> + chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); >>> + if (IS_ERR(chip->mode_mgr)) >>> + return PTR_ERR(chip->mode_mgr); >>> + } >>> + >>> + /* Check for any SoC specific config data */ >>> + chip->eud_cfg = of_device_get_match_data(&pdev->dev); >>> + if (chip->eud_cfg) { >>> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "tcsr-base"); >>> + if (!res) >>> + return dev_err_probe(chip->dev, -ENODEV, >>> + "failed to get tcsr reg base\n"); >>> + >>> + tcsr_base = res->start; >> This variable does not seem very useful, we can get rid of it. > > Ok. > >>> + tcsr_check = tcsr_base + chip->eud_cfg->tcsr_check_offset; >>> + >>> + ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); >>> + if (ret) >>> + return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n"); >>> + } >>> >>> chip->irq = platform_get_irq(pdev, 0); >>> ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq, >>> @@ -230,8 +285,13 @@ static int eud_remove(struct platform_device *pdev) >>> return 0; >>> } >>> >>> +static const struct eud_soc_cfg sm6115_eud_cfg = { >> This could be marked __initconst, but I'm not sure if future >> additions won't need to be accessed after the driver has already >> gone through its probe function.. Your call! > > Like Dmitry also mentioned, I have my apprehensions as well marking this > as __initconst, so let's not do that. Right, thanks Dmitry for pointing this out, I didn't think of usecases where a driver can be removed.. Konrad > > I will wait for a few more comments and then will send a new version across. > > Thanks, > Bhupesh > >>> + .tcsr_check_offset = 0x25018, >>> +}; >>> + >>> static const struct of_device_id eud_dt_match[] = { >>> { .compatible = "qcom,sc7280-eud" }, >>> + { .compatible = "qcom,sm6115-eud", .data = &sm6115_eud_cfg }, >>> { } >>> }; >>> MODULE_DEVICE_TABLE(of, eud_dt_match);
diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 99b15b77dfd5..fe1b5fec1dfc 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -147,6 +147,7 @@ config USB_APPLEDISPLAY config USB_QCOM_EUD tristate "QCOM Embedded USB Debugger(EUD) Driver" depends on ARCH_QCOM || COMPILE_TEST + select QCOM_SCM select USB_ROLE_SWITCH help This module enables support for Qualcomm Technologies, Inc. diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c index b7f13df00764..18a2dee3b4b9 100644 --- a/drivers/usb/misc/qcom_eud.c +++ b/drivers/usb/misc/qcom_eud.c @@ -5,12 +5,14 @@ #include <linux/bitops.h> #include <linux/err.h> +#include <linux/firmware/qcom/qcom_scm.h> #include <linux/interrupt.h> #include <linux/io.h> #include <linux/iopoll.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/of.h> +#include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/sysfs.h> @@ -22,23 +24,35 @@ #define EUD_REG_VBUS_INT_CLR 0x0080 #define EUD_REG_CSR_EUD_EN 0x1014 #define EUD_REG_SW_ATTACH_DET 0x1018 -#define EUD_REG_EUD_EN2 0x0000 +#define EUD_REG_EUD_EN2 0x0000 #define EUD_ENABLE BIT(0) -#define EUD_INT_PET_EUD BIT(0) +#define EUD_INT_PET_EUD BIT(0) #define EUD_INT_VBUS BIT(2) #define EUD_INT_SAFE_MODE BIT(4) #define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE) +#define EUD_EN2_SECURE_EN BIT(0) +#define EUD_EN2_NONSECURE_EN (1) +#define EUD_EN2_DISABLE (0) +#define TCSR_CHECK_EN BIT(0) + +struct eud_soc_cfg { + u32 tcsr_check_offset; +}; + struct eud_chip { struct device *dev; struct usb_role_switch *role_sw; + const struct eud_soc_cfg *eud_cfg; void __iomem *base; void __iomem *mode_mgr; unsigned int int_status; int irq; bool enabled; bool usb_attached; + bool secure_mode_enable; + phys_addr_t secure_mode_mgr; }; static int enable_eud(struct eud_chip *priv) @@ -46,7 +60,11 @@ static int enable_eud(struct eud_chip *priv) writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN); writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE, priv->base + EUD_REG_INT1_EN_MASK); - writel(1, priv->mode_mgr + EUD_REG_EUD_EN2); + + if (priv->secure_mode_mgr) + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_SECURE_EN); + else + writel(EUD_EN2_NONSECURE_EN, priv->mode_mgr + EUD_REG_EUD_EN2); return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE); } @@ -54,7 +72,11 @@ static int enable_eud(struct eud_chip *priv) static void disable_eud(struct eud_chip *priv) { writel(0, priv->base + EUD_REG_CSR_EUD_EN); - writel(0, priv->mode_mgr + EUD_REG_EUD_EN2); + + if (priv->secure_mode_mgr) + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE); + else + writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2); } static ssize_t enable_show(struct device *dev, @@ -178,6 +200,8 @@ static void eud_role_switch_release(void *data) static int eud_probe(struct platform_device *pdev) { struct eud_chip *chip; + struct resource *res; + phys_addr_t tcsr_base, tcsr_check; int ret; chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); @@ -200,9 +224,40 @@ static int eud_probe(struct platform_device *pdev) if (IS_ERR(chip->base)) return PTR_ERR(chip->base); - chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); - if (IS_ERR(chip->mode_mgr)) - return PTR_ERR(chip->mode_mgr); + chip->secure_mode_enable = of_property_read_bool(chip->dev->of_node, + "qcom,secure-mode-enable"); + /* + * EUD block on a few Qualcomm SoCs need secure register access. + * Check for the same. + */ + if (chip->secure_mode_enable) { + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!res) + return dev_err_probe(chip->dev, -ENODEV, + "failed to get secure_mode_mgr reg base\n"); + + chip->secure_mode_mgr = res->start; + } else { + chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); + if (IS_ERR(chip->mode_mgr)) + return PTR_ERR(chip->mode_mgr); + } + + /* Check for any SoC specific config data */ + chip->eud_cfg = of_device_get_match_data(&pdev->dev); + if (chip->eud_cfg) { + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "tcsr-base"); + if (!res) + return dev_err_probe(chip->dev, -ENODEV, + "failed to get tcsr reg base\n"); + + tcsr_base = res->start; + tcsr_check = tcsr_base + chip->eud_cfg->tcsr_check_offset; + + ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); + if (ret) + return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n"); + } chip->irq = platform_get_irq(pdev, 0); ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq, @@ -230,8 +285,13 @@ static int eud_remove(struct platform_device *pdev) return 0; } +static const struct eud_soc_cfg sm6115_eud_cfg = { + .tcsr_check_offset = 0x25018, +}; + static const struct of_device_id eud_dt_match[] = { { .compatible = "qcom,sc7280-eud" }, + { .compatible = "qcom,sm6115-eud", .data = &sm6115_eud_cfg }, { } }; MODULE_DEVICE_TABLE(of, eud_dt_match);
Add SM6115 / SM4250 SoC EUD support in qcom_eud driver. On some SoCs (like the SM6115 / SM4250 SoC), the mode manager needs to be accessed only via the secure world (through 'scm' calls). Also, the enable bit inside 'tcsr_check_reg' needs to be set first to set the eud in 'enable' mode on these SoCs. Since this difference comes from how the firmware is configured, so the driver now relies on the presence of an extra boolean DT property to identify if secure access is needed. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> --- drivers/usb/misc/Kconfig | 1 + drivers/usb/misc/qcom_eud.c | 74 +++++++++++++++++++++++++++++++++---- 2 files changed, 68 insertions(+), 7 deletions(-)