| Message ID | 20230416133422.1949-13-aweber.kernel@gmail.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Re-introduce Exynos4212 support and add Samsung Galaxy Tab 3 8.0 boards | expand |
Hi Artur, Nice to see some more Exynos arm boards! As Krzysztof already said this does not apply on top of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux.git/log/?h=next/dt, but it seems to apply on top of v6.3-rc6. If you use the --base arg of git format-patch it makes it easier to figure out where it applies. Running ./script/checkpatch.pl on the patches also points out two typos in exynos4x12.dtsi and exynos4212.dtsi, would probably be nice to fix those while you are at it. See some more comments/questions below. On Sun, Apr 16, 2023 at 03:34:22PM +0200, Artur Weber wrote: > Introduce support for the Galaxy Tab 3 8.0 series of boards: > > - Samsung Galaxy Tab 3 8.0 WiFi (SM-T310/lt01wifi) > - Samsung Galaxy Tab 3 8.0 3G (SM-T311/lt013g) > - Samsung Galaxy Tab 3 8.0 LTE (SM-T315/lt01lte) > > What works: > > - Display and backlight > - Touchscreen (without touchkeys) > - GPIO buttons, hall sensor > - WiFi and Bluetooth > - USB, fuel gauge, charging (partial) > - Accelerometer and magnetometer > - WiFi model only: light sensor > > Signed-off-by: Artur Weber <aweber.kernel@gmail.com> > --- > Display panel bindings are added by a separate patchset: > "[PATCH 0/3] Add Samsung S6D7AA0 panel controller driver"[1] > > [1] https://lore.kernel.org/all/20230416131632.31673-1-aweber.kernel@gmail.com/ > --- > arch/arm/boot/dts/Makefile | 3 + > arch/arm/boot/dts/exynos4212-tab3-3g8.dts | 30 + > arch/arm/boot/dts/exynos4212-tab3-lte8.dts | 43 + > arch/arm/boot/dts/exynos4212-tab3-wifi8.dts | 25 + > arch/arm/boot/dts/exynos4212-tab3.dtsi | 1175 +++++++++++++++++++ > 5 files changed, 1276 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos4212-tab3-3g8.dts > create mode 100644 arch/arm/boot/dts/exynos4212-tab3-lte8.dts > create mode 100644 arch/arm/boot/dts/exynos4212-tab3-wifi8.dts > create mode 100644 arch/arm/boot/dts/exynos4212-tab3.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index efe4152e5846..e5f63b636637 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -217,6 +217,9 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ > exynos4210-smdkv310.dtb \ > exynos4210-trats.dtb \ > exynos4210-universal_c210.dtb \ > + exynos4212-tab3-3g8.dtb \ > + exynos4212-tab3-lte8.dtb \ > + exynos4212-tab3-wifi8.dtb \ > exynos4412-i9300.dtb \ > exynos4412-i9305.dtb \ > exynos4412-itop-elite.dtb \ > diff --git a/arch/arm/boot/dts/exynos4212-tab3-3g8.dts b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts > new file mode 100644 > index 000000000000..c503a2d351dd > --- /dev/null > +++ b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts > @@ -0,0 +1,30 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree > + * source > + * > + * Copyright (c) 2013 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + */ > + > +/dts-v1/; > +#include "exynos4212-tab3.dtsi" > + > +/ { > + model = "Samsung Galaxy Tab 3 8.0 3G (SM-T311) based on Exynos4212"; > + compatible = "samsung,t311", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; > + chassis-type = "tablet"; > +}; > + > +/* Pin control sleep state overrides */ > + > +&sleep0 { > + PIN_SLP(gpb-5, INPUT, UP); > +}; > + > +&sleep1 { > + PIN_SLP(gpl0-0, OUT0, NONE); > + PIN_SLP(gpl1-0, OUT0, NONE); > + PIN_SLP(gpl2-4, OUT0, NONE); > + PIN_SLP(gpm3-3, OUT1, NONE); > +}; > diff --git a/arch/arm/boot/dts/exynos4212-tab3-lte8.dts b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts > new file mode 100644 > index 000000000000..158c6a2e24bf > --- /dev/null > +++ b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts > @@ -0,0 +1,43 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree > + * source > + * > + * Copyright (c) 2013 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + */ > + > +/dts-v1/; > +#include "exynos4212-tab3.dtsi" > + > +/ { > + model = "Samsung Galaxy Tab 3 8.0 LTE (SM-T315) based on Exynos4212"; > + compatible = "samsung,t315", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; > + chassis-type = "tablet"; > +}; > + > +&sleep0 { > + PIN_SLP(gpa0-4, INPUT, UP); > + PIN_SLP(gpa0-5, INPUT, UP); > + > + PIN_SLP(gpb-5, INPUT, UP); > + > + PIN_SLP(gpc0-0, PREV, NONE); > + PIN_SLP(gpc1-3, INPUT, NONE); > + > + PIN_SLP(gpf1-6, INPUT, NONE); > + PIN_SLP(gpf2-2, PREV, NONE); > +}; > + > +&sleep1 { > + PIN_SLP(gpl0-0, PREV, NONE); > + > + PIN_SLP(gpl1-0, PREV, NONE); > + > + PIN_SLP(gpl2-1, INPUT, DOWN); > + PIN_SLP(gpl2-2, INPUT, DOWN); > + PIN_SLP(gpl2-4, OUT0, NONE); > + PIN_SLP(gpl2-5, PREV, NONE); > + > + PIN_SLP(gpm3-3, OUT1, NONE); > +}; > diff --git a/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts > new file mode 100644 > index 000000000000..0527a75710d8 > --- /dev/null > +++ b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts > @@ -0,0 +1,25 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree > + * source > + * > + * Copyright (c) 2013 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + */ > + > +/dts-v1/; > +#include "exynos4212-tab3.dtsi" > + > +/ { > + model = "Samsung Galaxy Tab 3 8.0 WiFi (SM-T310) based on Exynos4212"; > + compatible = "samsung,t310", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; > + chassis-type = "tablet"; > +}; > + > +&i2c_lightsensor { > + /* Capella Micro CM3323 color light sensor */ > + colorsensor@10 { > + compatible = "capella,cm3323"; > + reg = <0x10>; > + }; > +}; > diff --git a/arch/arm/boot/dts/exynos4212-tab3.dtsi b/arch/arm/boot/dts/exynos4212-tab3.dtsi > new file mode 100644 > index 000000000000..b8ad5497506c > --- /dev/null > +++ b/arch/arm/boot/dts/exynos4212-tab3.dtsi > @@ -0,0 +1,1175 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Samsung's Exynos4212 based Galaxy Tab 3 board common source > + * > + * Copyright (c) 2013 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + */ > + > +/dts-v1/; > +#include "exynos4212.dtsi" > +#include "exynos4412-ppmu-common.dtsi" > +#include "exynos-mfc-reserved-memory.dtsi" > +#include <dt-bindings/clock/samsung,s2mps11.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/gpio-keys.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include "exynos-pinctrl.h" > + > +/ { > + compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; > + > + memory@40000000 { > + device_type = "memory"; > + > + /* Technically 2GB, but last 1GB is flaky, so we ignore it for now */ > + reg = <0x40000000 0x3FC00000>; Comment says 1GB but you are skipping 1GB+4MB. Is the entire region flaky or perhaps just the 4MB region in the middle? > + }; > + > + chosen { > + stdout-path = &serial_2; > + > + /* Default S-BOOT bootloader loads initramfs here */ > + linux,initrd-start = <0x42000000>; > + linux,initrd-end = <0x42800000>; > + }; > + > + firmware@204f000 { > + compatible = "samsung,secure-firmware"; > + reg = <0x0204F000 0x1000>; > + }; > + > + fixed-rate-clocks { > + xxti { > + compatible = "samsung,clock-xxti"; > + clock-frequency = <0>; > + }; > + > + xusbxti { > + compatible = "samsung,clock-xusbxti"; > + clock-frequency = <24000000>; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys>; > + > + key-power { > + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_POWER>; > + label = "power"; > + debounce-interval = <10>; > + wakeup-source; > + }; > + > + key-up { > + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + label = "volume down"; > + debounce-interval = <10>; > + }; > + > + key-down { > + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEDOWN>; > + label = "volume up"; > + debounce-interval = <10>; > + }; > + > + key-home { > + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_HOME>; > + label = "home"; > + debounce-interval = <10>; > + }; > + > + switch-hall-sensor { > + gpios = <&gpx2 4 GPIO_ACTIVE_LOW>; > + linux,input-type = <EV_SW>; > + linux,code = <SW_LID>; > + linux,can-disable; > + label = "hall effect sensor"; > + debounce-interval = <10>; > + wakeup-source; > + }; > + }; > + > + vbatt_reg: voltage-regulator-1 { > + compatible = "regulator-fixed"; > + regulator-name = "VBATT"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + backlight_reset_supply: voltage-regulator-2 { > + compatible = "regulator-fixed"; > + regulator-name = "BACKLIGHT_ENVDDIO"; > + pinctrl-names = "default"; > + pinctrl-0 = <&backlight_reset>; > + gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + lcd_enable_supply: voltage-regulator-3 { > + compatible = "regulator-fixed"; > + regulator-name = "LCD_VDD_2.2V"; > + regulator-min-microvolt = <2200000>; > + regulator-max-microvolt = <2200000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&lcd_en>; > + gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */ > + enable-active-high; > + }; > + > + i2c_max77693: i2c-gpio-1 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + pmic@66 { > + compatible = "maxim,max77693"; > + interrupt-parent = <&gpx1>; > + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&max77693_irq>; > + reg = <0x66>; > + > + regulators { > + esafeout1_reg: ESAFEOUT1 { > + regulator-name = "ESAFEOUT1"; > + regulator-boot-on; > + }; > + > + esafeout2_reg: ESAFEOUT2 { > + regulator-name = "ESAFEOUT2"; > + }; > + > + charger_reg: CHARGER { > + regulator-name = "CHARGER"; > + regulator-min-microamp = <60000>; > + regulator-max-microamp = <2580000>; > + regulator-boot-on; > + }; > + }; > + > + charger { > + compatible = "maxim,max77693-charger"; > + > + maxim,constant-microvolt = <4350000>; > + maxim,min-system-microvolt = <3600000>; > + maxim,thermal-regulation-celsius = <100>; > + maxim,battery-overcurrent-microamp = <3500000>; > + maxim,charge-input-threshold-microvolt = <4300000>; > + }; > + }; > + }; > + > + i2c_max77693_fuel: i2c-gpio-2 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + fuel-gauge@36 { > + compatible = "maxim,max17050"; > + interrupt-parent = <&gpx2>; > + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&max77693_fuel_irq>; > + reg = <0x36>; > + > + maxim,over-heat-temp = <500>; > + maxim,over-volt = <4500>; > + }; > + }; > + > + i2c_yas532_magnetometer: i2c-gpio-3 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + /* Magnetometer: Yamaha YAS532 */ > + magnetometer@2e { > + compatible = "yamaha,yas532"; > + reg = <0x2e>; > + iovdd-supply = <&ldo3_reg>; /* VCC_1.8V_AP */ > + mount-matrix = "-1", "0", "0", > + "0", "1", "0", > + "0", "0", "-1"; > + }; > + }; > + > + i2c_lightsensor: i2c-gpio-4 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + /* WiFi model uses CM3323, 3G/LTE use CM36653 */ > + }; > + > + i2c_bl: i2c-gpio-24 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + backlight: backlight@2c { > + compatible = "ti,lp8556"; > + reg = <0x2c>; > + status = "okay"; > + > + bl-name = "lcd-bl"; > + dev-ctrl = /bits/ 8 <0x80>; > + init-brt = /bits/ 8 <0x78>; /* 120 */ > + > + power-supply = <&vbatt_reg>; > + enable-supply = <&backlight_reset_supply>; > + > + pwms = <&pwm 1 78770 0>; > + pwm-names = "lp8556"; > + pwm-period = <78770>; > + > + rom_a3h { > + rom-addr = /bits/ 8 <0xa3>; > + rom-val = /bits/ 8 <0x5e>; > + }; > + > + rom_a5h { > + rom-addr = /bits/ 8 <0xa5>; > + rom-val = /bits/ 8 <0x34>; > + }; > + > + rom_a7h { > + rom-addr = /bits/ 8 <0xa7>; > + rom-val = /bits/ 8 <0xfa>; > + }; > + }; > + }; > + > + wlan_pwrseq: sdhci3-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; > + }; > +}; > + > +&bus_dmc { > + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; > + vdd-supply = <&buck1_reg>; > + status = "okay"; > +}; > + > +&bus_acp { > + devfreq = <&bus_dmc>; > + status = "okay"; > +}; > + > +&bus_c2c { > + devfreq = <&bus_dmc>; > + status = "okay"; > +}; > + > +&bus_leftbus { > + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; > + vdd-supply = <&buck3_reg>; > + status = "okay"; > +}; > + > +&bus_rightbus { > + devfreq = <&bus_leftbus>; > + status = "okay"; > +}; > + > +&bus_display { > + devfreq = <&bus_leftbus>; > + status = "okay"; > +}; > + > +&bus_fsys { > + devfreq = <&bus_leftbus>; > + status = "okay"; > +}; > + > +&bus_peri { > + devfreq = <&bus_leftbus>; > + status = "okay"; > +}; > + > +&bus_mfc { > + devfreq = <&bus_leftbus>; > + status = "okay"; > +}; > + > +&cpu0 { > + cpu0-supply = <&buck2_reg>; > +}; > + > +&dsi_0 { > + vddcore-supply = <&ldo8_reg>; > + vddio-supply = <&ldo10_reg>; > + samsung,burst-clock-frequency = <500000000>; > + samsung,esc-clock-frequency = <20000000>; > + samsung,pll-clock-frequency = <24000000>; > + status = "okay"; > + > + panel@0 { > + compatible = "samsung,s6d7aa0-lsl080al02"; > + reg = <0>; > + enable-supply = <&lcd_enable_supply>; > + pinctrl-names = "default"; > + pinctrl-0 = <&lcd_nrst>; > + reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>; > + backlight = <&backlight>; > + }; > +}; > + > +&exynos_usbphy { > + vbus-supply = <&esafeout1_reg>; > + status = "okay"; > +}; > + > +&fimd { > + status = "okay"; > +}; > + > +&gpu { > + mali-supply = <&buck4_reg>; > + status = "okay"; > +}; > + > +&hsotg { > + vusb_d-supply = <&ldo15_reg>; > + vusb_a-supply = <&ldo12_reg>; > + dr_mode = "peripheral"; > + status = "okay"; > +}; > + > +/* Accelerometer: K2DH/K3DH */ > +&i2c_1 { > + pinctrl-0 = <&i2c1_bus>; > + pinctrl-names = "default"; > + status = "okay"; > + > + lis3dh: accelerometer@19 { > + /* K2DH seems to be the same as lis2dh12 in terms of registers */ > + compatible = "st,lis2dh12-accel"; > + reg = <0x19>; > + > + interrupt-parent = <&gpx0>; > + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; > + > + vdd-supply = <&ldo17_reg>; /* VCC_2.8V_AP */ > + vddio-supply = <&ldo3_reg>; /* VCC_1.8V_AP */ > + > + mount-matrix = "-1", "0", "0", > + "0", "1", "0", > + "0", "0", "-1"; > + }; > +}; > + > +/* Touchscreen: MMS252 */ > +&i2c_3 { > + samsung,i2c-sda-delay = <100>; > + samsung,i2c-slave-addr = <0x10>; > + samsung,i2c-max-bus-freq = <400000>; > + pinctrl-0 = <&i2c3_bus>; > + pinctrl-names = "default"; > + status = "okay"; > + > + touchscreen@48 { > + /* Using mms114 compatible for now */ > + compatible = "melfas,mms114"; > + reg = <0x48>; > + interrupt-parent = <&gpb>; > + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; > + touchscreen-size-x = <800>; > + touchscreen-size-y = <1280>; > + avdd-supply = <&ldo21_reg>; > + vdd-supply = <&ldo25_reg>; > + }; > +}; > + > +/* PMIC: s5m8767 */ > +&i2c_7 { > + samsung,i2c-sda-delay = <100>; > + samsung,i2c-slave-addr = <0x10>; > + samsung,i2c-max-bus-freq = <100000>; > + pinctrl-0 = <&i2c7_bus>; > + pinctrl-names = "default"; > + status = "okay"; > + > + s5m8767: pmic@66 { > + compatible = "samsung,s5m8767-pmic"; > + reg = <0x66>; > + interrupt-parent = <&gpx0>; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; > + wakeup-source; > + > + s5m8767,pmic-buck2-ramp-enable; > + s5m8767,pmic-buck3-ramp-enable; > + s5m8767,pmic-buck4-ramp-enable; > + > + s5m8767,pmic-buck-ramp-delay = <25>; > + s5m8767,pmic-buck-default-dvs-idx = <1>; > + > + s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>, > + <&gpm3 1 GPIO_ACTIVE_HIGH>, > + <&gpm3 2 GPIO_ACTIVE_HIGH>; > + > + s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>, > + <&gpf3 2 GPIO_ACTIVE_HIGH>, > + <&gpf3 3 GPIO_ACTIVE_HIGH>; > + > + s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1100000>, <1100000>; > + > + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1100000>, <1100000>; > + > + s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1100000>, <1100000>; > + > + regulators { > + ldo1_reg: LDO1 { > + regulator-name = "VALIVE_1.0V_AP"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <1>; > + }; > + > + ldo2_reg: LDO2 { > + regulator-name = "VM1M2_1.2V_AP"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <1>; > + }; > + > + ldo3_reg: LDO3 { > + regulator-name = "VCC_1.8V_AP"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + op_mode = <1>; > + }; > + > + ldo5_reg: LDO5 { > + regulator-name = "VCC_3.3V_MHL"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + op_mode = <1>; > + }; > + > + ldo8_reg: LDO8 { > + regulator-name = "VMIPI_1.0V"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + op_mode = <3>; > + }; > + > + ldo9_reg: LDO9 { > + regulator-name = "VSIL_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + op_mode = <1>; > + }; > + > + ldo10_reg: LDO10 { > + regulator-name = "VMIPI_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + op_mode = <3>; > + }; > + > + ldo12_reg: LDO12 { > + regulator-name = "VUOTG_3.0V"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + op_mode = <1>; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + ldo13_reg: LDO13 { > + regulator-name = "VCC_1.8V_MHL"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + op_mode = <1>; > + }; > + > + ldo15_reg: LDO15 { > + regulator-name = "VHSIC_1.0V"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + op_mode = <1>; > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + ldo17_reg: LDO17 { > + regulator-name = "VCC_2.8V_AP"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + op_mode = <1>; > + regulator-always-on; > + }; > + > + ldo19_reg: LDO19 { > + regulator-name = "VLED_IC_1.9V"; > + regulator-min-microvolt = <1900000>; > + regulator-max-microvolt = <1900000>; > + op_mode = <1>; > + regulator-always-on; > + }; > + > + ldo20_reg: LDO20 { > + regulator-name = "VTOUCH_3.3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + op_mode = <1>; > + }; > + > + ldo21_reg: LDO21 { > + regulator-name = "TSP_VDD_3.3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + op_mode = <1>; > + }; > + > + ldo22_reg: LDO22 { > + regulator-name = "5M_AF_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + op_mode = <1>; > + }; > + > + ldo23_reg: LDO23 { > + regulator-name = "VTF_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + op_mode = <3>; > + }; > + > + ldo24_reg: LDO24 { > + regulator-name = "LEDA_2.8V"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + op_mode = <1>; > + }; > + > + ldo25_reg: LDO25 { > + regulator-name = "TSP_VDD_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + op_mode = <1>; > + }; > + > + ldo26_reg: LDO26 { > + regulator-name = "CAM_IO_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + op_mode = <1>; > + }; > + > + ldo27_reg: LDO27 { > + regulator-name = "VTCAM_1.8V"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + op_mode = <1>; > + }; > + > + buck1_reg: BUCK1 { > + regulator-name = "VDD_MIF"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1100000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + buck2_reg: BUCK2 { > + regulator-name = "VDD_ARM"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + buck3_reg: BUCK3 { > + regulator-name = "VDD_INT"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + buck4_reg: BUCK4 { > + regulator-name = "VDD_G3D"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1150000>; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + buck5_reg: BUCK5 { > + regulator-name = "VMEM_1.2V_AP"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <1>; > + }; > + > + buck6_reg: BUCK6 { > + regulator-name = "CAM_ISP_CORE_1.2V"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + op_mode = <1>; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + }; > + > + s5m8767_osc: clocks { > + compatible = "samsung,s5m8767-clk"; > + #clock-cells = <1>; > + clock-output-names = "en32khz_ap", > + "en32khz_cp", > + "en32khz_bt"; > + }; > + }; > +}; > + > +&mshc_0 { > + broken-cd; > + non-removable; > + card-detect-delay = <200>; > + vmmc-supply = <&ldo22_reg>; > + clock-frequency = <400000000>; > + samsung,dw-mshc-ciu-div = <0>; > + samsung,dw-mshc-sdr-timing = <2 3>; > + samsung,dw-mshc-ddr-timing = <1 2>; > + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; > + pinctrl-names = "default"; > + status = "okay"; > + bus-width = <8>; > + cap-mmc-highspeed; Please add mmc-ddr-1_8v; here as well. It was added to the other Exynos devices in commit 37f9514e618f ("ARM: dts: exynos: replace mshc0 alias with mmc-ddr-1_8v property") which can be found in Krzysztof's tree. Best regards, Henrik Grimler > +}; > + > +&pinctrl_0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&sleep0>; > + > + s5m8767_ds: s5m8767-ds { > + samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; > + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; > + }; > + > + lcd_en: lcd-en { > + samsung,pins = "gpc0-1"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + lcd_nrst: lcd-nrst { > + samsung,pins = "gpf0-4"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + sleep0: sleep-state { > + PIN_SLP(gpa0-0, INPUT, NONE); > + PIN_SLP(gpa0-1, OUT0, NONE); > + PIN_SLP(gpa0-2, INPUT, NONE); > + PIN_SLP(gpa0-3, INPUT, UP); > + PIN_SLP(gpa0-4, INPUT, DOWN); /* UP on LTE model */ > + PIN_SLP(gpa0-5, INPUT, DOWN); /* UP on LTE model */ > + PIN_SLP(gpa0-6, INPUT, DOWN); > + PIN_SLP(gpa0-7, INPUT, DOWN); > + > + PIN_SLP(gpa1-0, INPUT, DOWN); > + PIN_SLP(gpa1-1, INPUT, DOWN); > + PIN_SLP(gpa1-2, INPUT, DOWN); > + PIN_SLP(gpa1-3, INPUT, DOWN); > + PIN_SLP(gpa1-4, INPUT, DOWN); > + PIN_SLP(gpa1-5, INPUT, DOWN); > + > + PIN_SLP(gpb-0, INPUT, NONE); > + PIN_SLP(gpb-1, INPUT, NONE); > + PIN_SLP(gpb-2, INPUT, NONE); > + PIN_SLP(gpb-3, INPUT, NONE); > + PIN_SLP(gpb-4, INPUT, DOWN); > + PIN_SLP(gpb-5, INPUT, DOWN); /* UP on all models with modem */ > + PIN_SLP(gpb-6, INPUT, DOWN); > + PIN_SLP(gpb-7, INPUT, DOWN); > + > + PIN_SLP(gpc0-0, INPUT, DOWN); /* PREV, NONE on LTE model */ > + PIN_SLP(gpc0-1, INPUT, DOWN); > + PIN_SLP(gpc0-2, INPUT, DOWN); > + PIN_SLP(gpc0-3, INPUT, DOWN); > + PIN_SLP(gpc0-4, INPUT, DOWN); > + > + PIN_SLP(gpc1-0, INPUT, DOWN); > + PIN_SLP(gpc1-1, INPUT, DOWN); > + PIN_SLP(gpc1-2, INPUT, DOWN); > + PIN_SLP(gpc1-3, INPUT, DOWN); /* NONE on LTE model */ > + PIN_SLP(gpc1-4, INPUT, DOWN); > + > + PIN_SLP(gpd0-0, INPUT, DOWN); > + PIN_SLP(gpd0-1, OUT0, NONE); > + PIN_SLP(gpd0-2, INPUT, NONE); > + PIN_SLP(gpd0-3, INPUT, NONE); > + > + PIN_SLP(gpd1-0, INPUT, DOWN); > + PIN_SLP(gpd1-1, INPUT, DOWN); > + PIN_SLP(gpd1-2, INPUT, NONE); > + PIN_SLP(gpd1-3, INPUT, NONE); > + > + PIN_SLP(gpf0-0, INPUT, DOWN); > + PIN_SLP(gpf0-1, INPUT, DOWN); > + PIN_SLP(gpf0-2, INPUT, DOWN); > + PIN_SLP(gpf0-3, INPUT, DOWN); > + PIN_SLP(gpf0-4, OUT0, NONE); > + PIN_SLP(gpf0-5, OUT0, NONE); > + PIN_SLP(gpf0-6, INPUT, DOWN); > + PIN_SLP(gpf0-7, INPUT, DOWN); > + > + PIN_SLP(gpf1-0, INPUT, DOWN); > + PIN_SLP(gpf1-1, INPUT, DOWN); > + PIN_SLP(gpf1-2, INPUT, DOWN); > + PIN_SLP(gpf1-3, INPUT, DOWN); > + PIN_SLP(gpf1-4, INPUT, DOWN); > + PIN_SLP(gpf1-5, INPUT, DOWN); > + PIN_SLP(gpf1-6, INPUT, DOWN); /* NONE on LTE model */ > + PIN_SLP(gpf1-7, INPUT, DOWN); > + > + PIN_SLP(gpf2-0, INPUT, DOWN); > + PIN_SLP(gpf2-1, INPUT, DOWN); > + PIN_SLP(gpf2-2, INPUT, DOWN); /* PREV, NONE on LTE model */ > + PIN_SLP(gpf2-3, INPUT, DOWN); > + PIN_SLP(gpf2-4, INPUT, DOWN); > + PIN_SLP(gpf2-5, INPUT, DOWN); > + PIN_SLP(gpf2-6, INPUT, DOWN); > + PIN_SLP(gpf2-7, INPUT, DOWN); > + > + PIN_SLP(gpf3-0, INPUT, DOWN); > + PIN_SLP(gpf3-1, INPUT, DOWN); > + PIN_SLP(gpf3-2, INPUT, DOWN); > + PIN_SLP(gpf3-3, INPUT, DOWN); > + PIN_SLP(gpf3-4, PREV, NONE); > + PIN_SLP(gpf3-5, OUT0, DOWN); > + > + PIN_SLP(gpj0-0, INPUT, DOWN); > + PIN_SLP(gpj0-1, INPUT, DOWN); > + PIN_SLP(gpj0-2, INPUT, DOWN); > + PIN_SLP(gpj0-3, OUT0, NONE); > + PIN_SLP(gpj0-4, INPUT, DOWN); > + PIN_SLP(gpj0-5, INPUT, DOWN); > + PIN_SLP(gpj0-6, OUT0, NONE); > + PIN_SLP(gpj0-7, OUT0, NONE); > + > + PIN_SLP(gpj1-0, OUT0, NONE); > + PIN_SLP(gpj1-1, INPUT, DOWN); > + PIN_SLP(gpj1-2, PREV, NONE); > + PIN_SLP(gpj1-3, INPUT, DOWN); > + PIN_SLP(gpj1-4, INPUT, DOWN); > + }; > +}; > + > +&pinctrl_1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&sleep1>; > + > + max77693_irq: max77693-irq { > + samsung,pins = "gpx1-5"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; > + }; > + > + max77693_fuel_irq: max77693-fuel-irq { > + samsung,pins = "gpx2-3"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; > + }; > + > + s5m8767_dvs: s5m8767-dvs { > + samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; > + }; > + > + s5m8767_irq: s5m8767-irq { > + samsung,pins = "gpx0-7"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; > + }; > + > + sdhci2_cd: sdhci2-cd-irq { > + samsung,pins = "gpx3-4"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; > + }; > + > + bt_shutdown: bt-shutdown-pins { > + samsung,pins = "gpl0-6"; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + bt_host_wakeup: bt-host-wakeup-pins { > + samsung,pins = "gpx2-6"; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + bt_device_wakeup: bt-device-wakeup-pins { > + samsung,pins = "gpx3-1"; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + backlight_reset: backlight-reset { > + samsung,pins = "gpm0-1"; > + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + gpio_keys: gpio-keys-pins { > + samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3"; > + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; > + }; > + > + sleep1: sleep-state { > + PIN_SLP(gpk0-0, PREV, NONE); > + PIN_SLP(gpk0-1, PREV, NONE); > + PIN_SLP(gpk0-2, PREV, NONE); > + PIN_SLP(gpk0-3, PREV, NONE); > + PIN_SLP(gpk0-4, PREV, NONE); > + PIN_SLP(gpk0-5, PREV, NONE); > + PIN_SLP(gpk0-6, PREV, NONE); > + > + PIN_SLP(gpk1-0, INPUT, DOWN); > + PIN_SLP(gpk1-1, INPUT, DOWN); > + PIN_SLP(gpk1-2, INPUT, DOWN); > + PIN_SLP(gpk1-3, PREV, NONE); > + PIN_SLP(gpk1-4, PREV, NONE); > + PIN_SLP(gpk1-5, PREV, NONE); > + PIN_SLP(gpk1-6, PREV, NONE); > + > + PIN_SLP(gpk2-0, INPUT, DOWN); > + PIN_SLP(gpk2-1, INPUT, DOWN); > + PIN_SLP(gpk2-2, INPUT, DOWN); > + PIN_SLP(gpk2-3, INPUT, DOWN); > + PIN_SLP(gpk2-4, INPUT, DOWN); > + PIN_SLP(gpk2-5, INPUT, DOWN); > + PIN_SLP(gpk2-6, INPUT, DOWN); > + > + PIN_SLP(gpk3-0, OUT0, NONE); > + PIN_SLP(gpk3-1, INPUT, NONE); > + PIN_SLP(gpk3-2, INPUT, DOWN); > + PIN_SLP(gpk3-3, INPUT, NONE); > + PIN_SLP(gpk3-4, INPUT, NONE); > + PIN_SLP(gpk3-5, INPUT, NONE); > + PIN_SLP(gpk3-6, INPUT, NONE); > + > + PIN_SLP(gpl0-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */ > + PIN_SLP(gpl0-1, INPUT, NONE); > + PIN_SLP(gpl0-2, INPUT, NONE); > + PIN_SLP(gpl0-3, INPUT, DOWN); > + PIN_SLP(gpl0-4, INPUT, DOWN); > + PIN_SLP(gpl0-6, PREV, NONE); > + > + PIN_SLP(gpl1-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */ > + PIN_SLP(gpl1-1, OUT0, NONE); > + PIN_SLP(gpl2-0, INPUT, DOWN); > + PIN_SLP(gpl2-1, PREV, NONE); /* INPUT, DOWN on LTE */ > + PIN_SLP(gpl2-2, PREV, NONE); /* INPUT, DOWN on LTE */ > + PIN_SLP(gpl2-3, INPUT, DOWN); > + PIN_SLP(gpl2-4, INPUT, DOWN); /* OUT0, NONE on models with modem */ > + PIN_SLP(gpl2-5, INPUT, DOWN); /* PREV, NONE on LTE */ > + PIN_SLP(gpl2-6, INPUT, DOWN); > + PIN_SLP(gpl2-7, INPUT, DOWN); > + > + PIN_SLP(gpm0-0, PREV, NONE); > + PIN_SLP(gpm0-1, OUT0, NONE); > + PIN_SLP(gpm0-2, INPUT, DOWN); > + PIN_SLP(gpm0-3, INPUT, DOWN); > + PIN_SLP(gpm0-4, INPUT, DOWN); > + PIN_SLP(gpm0-5, INPUT, DOWN); > + PIN_SLP(gpm0-6, INPUT, DOWN); > + PIN_SLP(gpm0-7, INPUT, DOWN); > + > + PIN_SLP(gpm1-0, INPUT, DOWN); > + PIN_SLP(gpm1-1, INPUT, DOWN); > + PIN_SLP(gpm1-2, INPUT, NONE); > + PIN_SLP(gpm1-3, INPUT, NONE); > + PIN_SLP(gpm1-4, INPUT, NONE); > + PIN_SLP(gpm1-5, INPUT, NONE); > + PIN_SLP(gpm1-6, OUT0, NONE); > + > + PIN_SLP(gpm2-0, INPUT, NONE); > + PIN_SLP(gpm2-1, INPUT, NONE); > + PIN_SLP(gpm2-2, OUT0, NONE); > + PIN_SLP(gpm2-3, INPUT, DOWN); > + PIN_SLP(gpm2-4, INPUT, DOWN); > + > + PIN_SLP(gpm3-0, PREV, NONE); > + PIN_SLP(gpm3-1, PREV, NONE); > + PIN_SLP(gpm3-2, PREV, NONE); > + PIN_SLP(gpm3-3, INPUT, DOWN); /* OUT1, NONE for 3G */ > + PIN_SLP(gpm3-4, INPUT, DOWN); > + PIN_SLP(gpm3-5, PREV, NONE); > + PIN_SLP(gpm3-6, INPUT, DOWN); > + PIN_SLP(gpm3-7, OUT0, NONE); > + > + PIN_SLP(gpm4-0, INPUT, DOWN); > + PIN_SLP(gpm4-1, INPUT, DOWN); > + PIN_SLP(gpm4-2, INPUT, DOWN); > + PIN_SLP(gpm4-3, INPUT, DOWN); > + PIN_SLP(gpm4-4, PREV, NONE); > + PIN_SLP(gpm4-5, INPUT, NONE); > + PIN_SLP(gpm4-6, INPUT, DOWN); > + PIN_SLP(gpm4-7, INPUT, DOWN); > + > + PIN_SLP(gpy0-0, INPUT, DOWN); > + PIN_SLP(gpy0-1, INPUT, DOWN); > + PIN_SLP(gpy0-2, INPUT, NONE); > + PIN_SLP(gpy0-3, INPUT, NONE); > + PIN_SLP(gpy0-4, INPUT, DOWN); > + PIN_SLP(gpy0-5, INPUT, DOWN); > + > + PIN_SLP(gpy1-0, INPUT, DOWN); > + PIN_SLP(gpy1-1, INPUT, DOWN); > + PIN_SLP(gpy1-2, INPUT, DOWN); > + PIN_SLP(gpy1-3, INPUT, DOWN); > + > + PIN_SLP(gpy2-0, PREV, NONE); > + PIN_SLP(gpy2-1, INPUT, DOWN); > + PIN_SLP(gpy2-2, INPUT, NONE); > + PIN_SLP(gpy2-3, INPUT, NONE); > + PIN_SLP(gpy2-4, INPUT, NONE); > + PIN_SLP(gpy2-5, INPUT, NONE); > + > + PIN_SLP(gpy3-0, INPUT, DOWN); > + PIN_SLP(gpy3-1, INPUT, DOWN); > + PIN_SLP(gpy3-2, INPUT, DOWN); > + PIN_SLP(gpy3-3, INPUT, DOWN); > + PIN_SLP(gpy3-4, INPUT, DOWN); > + PIN_SLP(gpy3-5, INPUT, DOWN); > + PIN_SLP(gpy3-6, INPUT, DOWN); > + PIN_SLP(gpy3-7, INPUT, DOWN); > + > + PIN_SLP(gpy4-0, INPUT, DOWN); > + PIN_SLP(gpy4-1, INPUT, DOWN); > + PIN_SLP(gpy4-2, INPUT, DOWN); > + PIN_SLP(gpy4-3, INPUT, DOWN); > + PIN_SLP(gpy4-4, INPUT, DOWN); > + PIN_SLP(gpy4-5, INPUT, DOWN); > + PIN_SLP(gpy4-6, INPUT, DOWN); > + PIN_SLP(gpy4-7, INPUT, DOWN); > + > + PIN_SLP(gpy5-0, INPUT, DOWN); > + PIN_SLP(gpy5-1, INPUT, DOWN); > + PIN_SLP(gpy5-2, INPUT, DOWN); > + PIN_SLP(gpy5-3, INPUT, DOWN); > + PIN_SLP(gpy5-4, INPUT, DOWN); > + PIN_SLP(gpy5-5, INPUT, DOWN); > + PIN_SLP(gpy5-6, INPUT, DOWN); > + PIN_SLP(gpy5-7, INPUT, DOWN); > + > + PIN_SLP(gpy6-0, INPUT, DOWN); > + PIN_SLP(gpy6-1, INPUT, DOWN); > + PIN_SLP(gpy6-2, INPUT, DOWN); > + PIN_SLP(gpy6-3, INPUT, DOWN); > + PIN_SLP(gpy6-4, INPUT, DOWN); > + PIN_SLP(gpy6-5, INPUT, DOWN); > + PIN_SLP(gpy6-6, INPUT, DOWN); > + PIN_SLP(gpy6-7, INPUT, DOWN); > + }; > +}; > + > +&pinctrl_2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&sleep2>; > + > + sleep2: sleep-state { > + PIN_SLP(gpz-0, INPUT, DOWN); > + PIN_SLP(gpz-1, INPUT, DOWN); > + PIN_SLP(gpz-2, INPUT, DOWN); > + PIN_SLP(gpz-3, INPUT, DOWN); > + PIN_SLP(gpz-4, INPUT, DOWN); > + PIN_SLP(gpz-5, INPUT, DOWN); > + PIN_SLP(gpz-6, INPUT, DOWN); > + }; > +}; > + > +&pinctrl_3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&sleep3>; > + > + sleep3: sleep-state { > + PIN_SLP(gpv0-0, INPUT, DOWN); > + PIN_SLP(gpv0-1, INPUT, DOWN); > + PIN_SLP(gpv0-2, INPUT, DOWN); > + PIN_SLP(gpv0-3, INPUT, DOWN); > + PIN_SLP(gpv0-4, INPUT, DOWN); > + PIN_SLP(gpv0-5, INPUT, DOWN); > + PIN_SLP(gpv0-6, INPUT, DOWN); > + PIN_SLP(gpv0-7, INPUT, DOWN); > + > + PIN_SLP(gpv1-0, INPUT, DOWN); > + PIN_SLP(gpv1-1, INPUT, DOWN); > + PIN_SLP(gpv1-2, INPUT, DOWN); > + PIN_SLP(gpv1-3, INPUT, DOWN); > + PIN_SLP(gpv1-4, INPUT, DOWN); > + PIN_SLP(gpv1-5, INPUT, DOWN); > + PIN_SLP(gpv1-6, INPUT, DOWN); > + PIN_SLP(gpv1-7, INPUT, DOWN); > + > + PIN_SLP(gpv2-0, INPUT, DOWN); > + PIN_SLP(gpv2-1, INPUT, DOWN); > + PIN_SLP(gpv2-2, INPUT, DOWN); > + PIN_SLP(gpv2-3, INPUT, DOWN); > + PIN_SLP(gpv2-4, INPUT, DOWN); > + PIN_SLP(gpv2-5, INPUT, DOWN); > + PIN_SLP(gpv2-6, INPUT, DOWN); > + PIN_SLP(gpv2-7, INPUT, DOWN); > + > + PIN_SLP(gpv3-0, INPUT, DOWN); > + PIN_SLP(gpv3-1, INPUT, DOWN); > + PIN_SLP(gpv3-2, INPUT, DOWN); > + PIN_SLP(gpv3-3, INPUT, DOWN); > + PIN_SLP(gpv3-4, INPUT, DOWN); > + PIN_SLP(gpv3-5, INPUT, DOWN); > + PIN_SLP(gpv3-6, INPUT, DOWN); > + PIN_SLP(gpv3-7, INPUT, DOWN); > + > + PIN_SLP(gpv4-0, INPUT, DOWN); > + PIN_SLP(gpv4-1, INPUT, DOWN); > + }; > +}; > + > +&pmu_system_controller { > + assigned-clocks = <&pmu_system_controller 0>; > + assigned-clock-parents = <&clock CLK_XUSBXTI>; > +}; > + > +&pwm { > + pinctrl-0 = <&pwm1_out>; > + pinctrl-names = "default"; > + samsung,pwm-outputs = <1>; > + status = "okay"; > +}; > + > +&rtc { > + status = "okay"; > + clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; > + clock-names = "rtc", "rtc_src"; > +}; > + > +&sdhci_2 { > + bus-width = <4>; > + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; > + pinctrl-names = "default"; > + vmmc-supply = <&ldo23_reg>; > + status = "okay"; > +}; > + > +&sdhci_3 { > + #address-cells = <1>; > + #size-cells = <0>; > + non-removable; > + bus-width = <4>; > + > + mmc-pwrseq = <&wlan_pwrseq>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; > + status = "okay"; > + > + /* BCM4334 Wi-Fi */ > + brcmf: wifi@1 { > + compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; > + reg = <1>; > + > + interrupt-parent = <&gpx2>; > + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "host-wake"; > + }; > +}; > + > +&serial_0 { > + pinctrl-0 = <&uart0_data &uart0_fctl>; > + pinctrl-names = "default"; > + status = "okay"; > + > + /* BCM4334B0 Bluetooth */ > + bluetooth { > + compatible = "brcm,bcm4330-bt"; > + pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; > + pinctrl-names = "default"; > + max-speed = <3000000>; > + shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; > + device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; > + host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; > + clocks = <&s5m8767_osc S2MPS11_CLK_BT>; > + }; > +}; > + > +&serial_1 { > + status = "okay"; > +}; > + > +&serial_2 { > + status = "okay"; > +}; > + > +&serial_3 { > + status = "okay"; > +}; > + > +&tmu { > + vtmu-supply = <&ldo10_reg>; > + status = "okay"; > +}; > -- > 2.40.0 >
Hi, thank you for the review. On 16/04/2023 20:26, Krzysztof Kozlowski wrote: > On 16/04/2023 15:34, Artur Weber wrote: > [...] >> + >> + backlight: backlight@2c { >> + compatible = "ti,lp8556"; > > You need to convert bindings to DT schema first. I don't accept any new > usages of TXT bindings anymore, sorry. > I'll be taking a look at the conversion (will likely submit it as a separate patchset, since I've been looking into some minor driver-side changes there as well...), although I have one question - who should I list as the bindings maintainer ("maintainers" field in YAML format)? Is this someone specific for that subsystem, or the author of the driver, or someone else? (It's worth noting that there isn't a maintainer listed for the lp855x driver in the MAINTAINERS file.) Documentation/devicetree/bindings/writing-schema.rst doesn't really mention anything about this. >> +&bus_acp { > > Order label/phandle overrides by name, so acp before dmc. > Out of curiosity - should I order the children of the / node or the pinctrl nodes by name as well? Best regards Artur Weber
Hi, On 19/04/2023 22:23, Henrik Grimler wrote: >> + memory@40000000 { >> + device_type = "memory"; >> + >> + /* Technically 2GB, but last 1GB is flaky, so we ignore it for now */ >> + reg = <0x40000000 0x3FC00000>; > > Comment says 1GB but you are skipping 1GB+4MB. Is the entire region > flaky or perhaps just the 4MB region in the middle? I copied the memory bank configuration from downstream: according to boot logs and ATAG data from the stock bootloader, there are two memory regions: one starting at 0x40000000 (size: 1020M) and one starting at 0x80000000 (size: 1024M). Here, only the first bank is added, since the second one doesn't work. I tried changing the size of this first bank to the full 1024M, and it seems to be booting fine; still, I'd rather leave this at the same size as claimed by downstream and ATAG. The second memory bank (anything past 0x80000000) doesn't work, as downstream has some weird special behavior regarding it: that region contains "page holes", and there's a check that discards every second page frame in that region[1][2]. That also means my comment is incorrect - indeed, 2GB of memory are passed to the kernel, but the second 1GB is effectively halved, leaving us with 1.5GB. (That's an oversight on my part - I wasn't aware of this when writing the DTS initially, and only checked this more in-depth now.) I'm not sure if there's a way to re-create this behavior in mainline; the closest thing I can think of is making a separate entry in reg for each of the working pages, but that would leave us with hundreds of lines, which is not ideal... so it's much easier to just leave it unused for now. Best regards Artur Weber [1] https://github.com/gr8nole/android_kernel_samsung_smdk4x12/blob/786b1473b93aabf40c18a2dca035503cce5ecac7/arch/arm/mm/init.c#L413-L414 [2] https://github.com/gr8nole/android_kernel_samsung_smdk4x12/blob/786b1473b93aabf40c18a2dca035503cce5ecac7/arch/arm/mach-exynos/include/mach/memory.h#L30-L38
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index efe4152e5846..e5f63b636637 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -217,6 +217,9 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \ exynos4210-universal_c210.dtb \ + exynos4212-tab3-3g8.dtb \ + exynos4212-tab3-lte8.dtb \ + exynos4212-tab3-wifi8.dtb \ exynos4412-i9300.dtb \ exynos4412-i9305.dtb \ exynos4412-itop-elite.dtb \ diff --git a/arch/arm/boot/dts/exynos4212-tab3-3g8.dts b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts new file mode 100644 index 000000000000..c503a2d351dd --- /dev/null +++ b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts @@ -0,0 +1,30 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree + * source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + */ + +/dts-v1/; +#include "exynos4212-tab3.dtsi" + +/ { + model = "Samsung Galaxy Tab 3 8.0 3G (SM-T311) based on Exynos4212"; + compatible = "samsung,t311", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; + chassis-type = "tablet"; +}; + +/* Pin control sleep state overrides */ + +&sleep0 { + PIN_SLP(gpb-5, INPUT, UP); +}; + +&sleep1 { + PIN_SLP(gpl0-0, OUT0, NONE); + PIN_SLP(gpl1-0, OUT0, NONE); + PIN_SLP(gpl2-4, OUT0, NONE); + PIN_SLP(gpm3-3, OUT1, NONE); +}; diff --git a/arch/arm/boot/dts/exynos4212-tab3-lte8.dts b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts new file mode 100644 index 000000000000..158c6a2e24bf --- /dev/null +++ b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts @@ -0,0 +1,43 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree + * source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + */ + +/dts-v1/; +#include "exynos4212-tab3.dtsi" + +/ { + model = "Samsung Galaxy Tab 3 8.0 LTE (SM-T315) based on Exynos4212"; + compatible = "samsung,t315", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; + chassis-type = "tablet"; +}; + +&sleep0 { + PIN_SLP(gpa0-4, INPUT, UP); + PIN_SLP(gpa0-5, INPUT, UP); + + PIN_SLP(gpb-5, INPUT, UP); + + PIN_SLP(gpc0-0, PREV, NONE); + PIN_SLP(gpc1-3, INPUT, NONE); + + PIN_SLP(gpf1-6, INPUT, NONE); + PIN_SLP(gpf2-2, PREV, NONE); +}; + +&sleep1 { + PIN_SLP(gpl0-0, PREV, NONE); + + PIN_SLP(gpl1-0, PREV, NONE); + + PIN_SLP(gpl2-1, INPUT, DOWN); + PIN_SLP(gpl2-2, INPUT, DOWN); + PIN_SLP(gpl2-4, OUT0, NONE); + PIN_SLP(gpl2-5, PREV, NONE); + + PIN_SLP(gpm3-3, OUT1, NONE); +}; diff --git a/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts new file mode 100644 index 000000000000..0527a75710d8 --- /dev/null +++ b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree + * source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + */ + +/dts-v1/; +#include "exynos4212-tab3.dtsi" + +/ { + model = "Samsung Galaxy Tab 3 8.0 WiFi (SM-T310) based on Exynos4212"; + compatible = "samsung,t310", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; + chassis-type = "tablet"; +}; + +&i2c_lightsensor { + /* Capella Micro CM3323 color light sensor */ + colorsensor@10 { + compatible = "capella,cm3323"; + reg = <0x10>; + }; +}; diff --git a/arch/arm/boot/dts/exynos4212-tab3.dtsi b/arch/arm/boot/dts/exynos4212-tab3.dtsi new file mode 100644 index 000000000000..b8ad5497506c --- /dev/null +++ b/arch/arm/boot/dts/exynos4212-tab3.dtsi @@ -0,0 +1,1175 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos4212 based Galaxy Tab 3 board common source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + */ + +/dts-v1/; +#include "exynos4212.dtsi" +#include "exynos4412-ppmu-common.dtsi" +#include "exynos-mfc-reserved-memory.dtsi" +#include <dt-bindings/clock/samsung,s2mps11.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include "exynos-pinctrl.h" + +/ { + compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; + + memory@40000000 { + device_type = "memory"; + + /* Technically 2GB, but last 1GB is flaky, so we ignore it for now */ + reg = <0x40000000 0x3FC00000>; + }; + + chosen { + stdout-path = &serial_2; + + /* Default S-BOOT bootloader loads initramfs here */ + linux,initrd-start = <0x42000000>; + linux,initrd-end = <0x42800000>; + }; + + firmware@204f000 { + compatible = "samsung,secure-firmware"; + reg = <0x0204F000 0x1000>; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <0>; + }; + + xusbxti { + compatible = "samsung,clock-xusbxti"; + clock-frequency = <24000000>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys>; + + key-power { + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + label = "power"; + debounce-interval = <10>; + wakeup-source; + }; + + key-up { + gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + label = "volume down"; + debounce-interval = <10>; + }; + + key-down { + gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + label = "volume up"; + debounce-interval = <10>; + }; + + key-home { + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOME>; + label = "home"; + debounce-interval = <10>; + }; + + switch-hall-sensor { + gpios = <&gpx2 4 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + label = "hall effect sensor"; + debounce-interval = <10>; + wakeup-source; + }; + }; + + vbatt_reg: voltage-regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "VBATT"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + backlight_reset_supply: voltage-regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "BACKLIGHT_ENVDDIO"; + pinctrl-names = "default"; + pinctrl-0 = <&backlight_reset>; + gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + lcd_enable_supply: voltage-regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "LCD_VDD_2.2V"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_en>; + gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */ + enable-active-high; + }; + + i2c_max77693: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + pmic@66 { + compatible = "maxim,max77693"; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&max77693_irq>; + reg = <0x66>; + + regulators { + esafeout1_reg: ESAFEOUT1 { + regulator-name = "ESAFEOUT1"; + regulator-boot-on; + }; + + esafeout2_reg: ESAFEOUT2 { + regulator-name = "ESAFEOUT2"; + }; + + charger_reg: CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <60000>; + regulator-max-microamp = <2580000>; + regulator-boot-on; + }; + }; + + charger { + compatible = "maxim,max77693-charger"; + + maxim,constant-microvolt = <4350000>; + maxim,min-system-microvolt = <3600000>; + maxim,thermal-regulation-celsius = <100>; + maxim,battery-overcurrent-microamp = <3500000>; + maxim,charge-input-threshold-microvolt = <4300000>; + }; + }; + }; + + i2c_max77693_fuel: i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + fuel-gauge@36 { + compatible = "maxim,max17050"; + interrupt-parent = <&gpx2>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&max77693_fuel_irq>; + reg = <0x36>; + + maxim,over-heat-temp = <500>; + maxim,over-volt = <4500>; + }; + }; + + i2c_yas532_magnetometer: i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + /* Magnetometer: Yamaha YAS532 */ + magnetometer@2e { + compatible = "yamaha,yas532"; + reg = <0x2e>; + iovdd-supply = <&ldo3_reg>; /* VCC_1.8V_AP */ + mount-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + }; + }; + + i2c_lightsensor: i2c-gpio-4 { + compatible = "i2c-gpio"; + sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + /* WiFi model uses CM3323, 3G/LTE use CM36653 */ + }; + + i2c_bl: i2c-gpio-24 { + compatible = "i2c-gpio"; + sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + backlight: backlight@2c { + compatible = "ti,lp8556"; + reg = <0x2c>; + status = "okay"; + + bl-name = "lcd-bl"; + dev-ctrl = /bits/ 8 <0x80>; + init-brt = /bits/ 8 <0x78>; /* 120 */ + + power-supply = <&vbatt_reg>; + enable-supply = <&backlight_reset_supply>; + + pwms = <&pwm 1 78770 0>; + pwm-names = "lp8556"; + pwm-period = <78770>; + + rom_a3h { + rom-addr = /bits/ 8 <0xa3>; + rom-val = /bits/ 8 <0x5e>; + }; + + rom_a5h { + rom-addr = /bits/ 8 <0xa5>; + rom-val = /bits/ 8 <0x34>; + }; + + rom_a7h { + rom-addr = /bits/ 8 <0xa7>; + rom-val = /bits/ 8 <0xfa>; + }; + }; + }; + + wlan_pwrseq: sdhci3-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; + }; +}; + +&bus_dmc { + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; + vdd-supply = <&buck1_reg>; + status = "okay"; +}; + +&bus_acp { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_c2c { + devfreq = <&bus_dmc>; + status = "okay"; +}; + +&bus_leftbus { + devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; + vdd-supply = <&buck3_reg>; + status = "okay"; +}; + +&bus_rightbus { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_display { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_fsys { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_peri { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&bus_mfc { + devfreq = <&bus_leftbus>; + status = "okay"; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&dsi_0 { + vddcore-supply = <&ldo8_reg>; + vddio-supply = <&ldo10_reg>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + samsung,pll-clock-frequency = <24000000>; + status = "okay"; + + panel@0 { + compatible = "samsung,s6d7aa0-lsl080al02"; + reg = <0>; + enable-supply = <&lcd_enable_supply>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_nrst>; + reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>; + backlight = <&backlight>; + }; +}; + +&exynos_usbphy { + vbus-supply = <&esafeout1_reg>; + status = "okay"; +}; + +&fimd { + status = "okay"; +}; + +&gpu { + mali-supply = <&buck4_reg>; + status = "okay"; +}; + +&hsotg { + vusb_d-supply = <&ldo15_reg>; + vusb_a-supply = <&ldo12_reg>; + dr_mode = "peripheral"; + status = "okay"; +}; + +/* Accelerometer: K2DH/K3DH */ +&i2c_1 { + pinctrl-0 = <&i2c1_bus>; + pinctrl-names = "default"; + status = "okay"; + + lis3dh: accelerometer@19 { + /* K2DH seems to be the same as lis2dh12 in terms of registers */ + compatible = "st,lis2dh12-accel"; + reg = <0x19>; + + interrupt-parent = <&gpx0>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + + vdd-supply = <&ldo17_reg>; /* VCC_2.8V_AP */ + vddio-supply = <&ldo3_reg>; /* VCC_1.8V_AP */ + + mount-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + }; +}; + +/* Touchscreen: MMS252 */ +&i2c_3 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + status = "okay"; + + touchscreen@48 { + /* Using mms114 compatible for now */ + compatible = "melfas,mms114"; + reg = <0x48>; + interrupt-parent = <&gpb>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + touchscreen-size-x = <800>; + touchscreen-size-y = <1280>; + avdd-supply = <&ldo21_reg>; + vdd-supply = <&ldo25_reg>; + }; +}; + +/* PMIC: s5m8767 */ +&i2c_7 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + pinctrl-0 = <&i2c7_bus>; + pinctrl-names = "default"; + status = "okay"; + + s5m8767: pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + interrupt-parent = <&gpx0>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; + wakeup-source; + + s5m8767,pmic-buck2-ramp-enable; + s5m8767,pmic-buck3-ramp-enable; + s5m8767,pmic-buck4-ramp-enable; + + s5m8767,pmic-buck-ramp-delay = <25>; + s5m8767,pmic-buck-default-dvs-idx = <1>; + + s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>, + <&gpm3 1 GPIO_ACTIVE_HIGH>, + <&gpm3 2 GPIO_ACTIVE_HIGH>; + + s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>, + <&gpf3 2 GPIO_ACTIVE_HIGH>, + <&gpf3 3 GPIO_ACTIVE_HIGH>; + + s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1100000>, <1100000>, + <1100000>, <1100000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1100000>, <1100000>, + <1100000>, <1100000>; + + s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1100000>, <1100000>, + <1100000>, <1100000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VALIVE_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VM1M2_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; + }; + + ldo3_reg: LDO3 { + regulator-name = "VCC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <1>; + }; + + ldo5_reg: LDO5 { + regulator-name = "VCC_3.3V_MHL"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; + }; + + ldo8_reg: LDO8 { + regulator-name = "VMIPI_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + op_mode = <3>; + }; + + ldo9_reg: LDO9 { + regulator-name = "VSIL_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + op_mode = <1>; + }; + + ldo10_reg: LDO10 { + regulator-name = "VMIPI_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <3>; + }; + + ldo12_reg: LDO12 { + regulator-name = "VUOTG_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + op_mode = <1>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo13_reg: LDO13 { + regulator-name = "VCC_1.8V_MHL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; + }; + + ldo15_reg: LDO15 { + regulator-name = "VHSIC_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + op_mode = <1>; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + ldo17_reg: LDO17 { + regulator-name = "VCC_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; + regulator-always-on; + }; + + ldo19_reg: LDO19 { + regulator-name = "VLED_IC_1.9V"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + op_mode = <1>; + regulator-always-on; + }; + + ldo20_reg: LDO20 { + regulator-name = "VTOUCH_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; + }; + + ldo21_reg: LDO21 { + regulator-name = "TSP_VDD_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; + }; + + ldo22_reg: LDO22 { + regulator-name = "5M_AF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; + }; + + ldo23_reg: LDO23 { + regulator-name = "VTF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <3>; + }; + + ldo24_reg: LDO24 { + regulator-name = "LEDA_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <1>; + }; + + ldo25_reg: LDO25 { + regulator-name = "TSP_VDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; + }; + + ldo26_reg: LDO26 { + regulator-name = "CAM_IO_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; + }; + + ldo27_reg: LDO27 { + regulator-name = "VTCAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + op_mode = <1>; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + + buck2_reg: BUCK2 { + regulator-name = "VDD_ARM"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + + buck3_reg: BUCK3 { + regulator-name = "VDD_INT"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + + buck4_reg: BUCK4 { + regulator-name = "VDD_G3D"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + op_mode = <3>; + }; + + buck5_reg: BUCK5 { + regulator-name = "VMEM_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; + }; + + buck6_reg: BUCK6 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + op_mode = <1>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + + s5m8767_osc: clocks { + compatible = "samsung,s5m8767-clk"; + #clock-cells = <1>; + clock-output-names = "en32khz_ap", + "en32khz_cp", + "en32khz_bt"; + }; + }; +}; + +&mshc_0 { + broken-cd; + non-removable; + card-detect-delay = <200>; + vmmc-supply = <&ldo22_reg>; + clock-frequency = <400000000>; + samsung,dw-mshc-ciu-div = <0>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; + pinctrl-names = "default"; + status = "okay"; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&pinctrl_0 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep0>; + + s5m8767_ds: s5m8767-ds { + samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + lcd_en: lcd-en { + samsung,pins = "gpc0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + lcd_nrst: lcd-nrst { + samsung,pins = "gpf0-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + sleep0: sleep-state { + PIN_SLP(gpa0-0, INPUT, NONE); + PIN_SLP(gpa0-1, OUT0, NONE); + PIN_SLP(gpa0-2, INPUT, NONE); + PIN_SLP(gpa0-3, INPUT, UP); + PIN_SLP(gpa0-4, INPUT, DOWN); /* UP on LTE model */ + PIN_SLP(gpa0-5, INPUT, DOWN); /* UP on LTE model */ + PIN_SLP(gpa0-6, INPUT, DOWN); + PIN_SLP(gpa0-7, INPUT, DOWN); + + PIN_SLP(gpa1-0, INPUT, DOWN); + PIN_SLP(gpa1-1, INPUT, DOWN); + PIN_SLP(gpa1-2, INPUT, DOWN); + PIN_SLP(gpa1-3, INPUT, DOWN); + PIN_SLP(gpa1-4, INPUT, DOWN); + PIN_SLP(gpa1-5, INPUT, DOWN); + + PIN_SLP(gpb-0, INPUT, NONE); + PIN_SLP(gpb-1, INPUT, NONE); + PIN_SLP(gpb-2, INPUT, NONE); + PIN_SLP(gpb-3, INPUT, NONE); + PIN_SLP(gpb-4, INPUT, DOWN); + PIN_SLP(gpb-5, INPUT, DOWN); /* UP on all models with modem */ + PIN_SLP(gpb-6, INPUT, DOWN); + PIN_SLP(gpb-7, INPUT, DOWN); + + PIN_SLP(gpc0-0, INPUT, DOWN); /* PREV, NONE on LTE model */ + PIN_SLP(gpc0-1, INPUT, DOWN); + PIN_SLP(gpc0-2, INPUT, DOWN); + PIN_SLP(gpc0-3, INPUT, DOWN); + PIN_SLP(gpc0-4, INPUT, DOWN); + + PIN_SLP(gpc1-0, INPUT, DOWN); + PIN_SLP(gpc1-1, INPUT, DOWN); + PIN_SLP(gpc1-2, INPUT, DOWN); + PIN_SLP(gpc1-3, INPUT, DOWN); /* NONE on LTE model */ + PIN_SLP(gpc1-4, INPUT, DOWN); + + PIN_SLP(gpd0-0, INPUT, DOWN); + PIN_SLP(gpd0-1, OUT0, NONE); + PIN_SLP(gpd0-2, INPUT, NONE); + PIN_SLP(gpd0-3, INPUT, NONE); + + PIN_SLP(gpd1-0, INPUT, DOWN); + PIN_SLP(gpd1-1, INPUT, DOWN); + PIN_SLP(gpd1-2, INPUT, NONE); + PIN_SLP(gpd1-3, INPUT, NONE); + + PIN_SLP(gpf0-0, INPUT, DOWN); + PIN_SLP(gpf0-1, INPUT, DOWN); + PIN_SLP(gpf0-2, INPUT, DOWN); + PIN_SLP(gpf0-3, INPUT, DOWN); + PIN_SLP(gpf0-4, OUT0, NONE); + PIN_SLP(gpf0-5, OUT0, NONE); + PIN_SLP(gpf0-6, INPUT, DOWN); + PIN_SLP(gpf0-7, INPUT, DOWN); + + PIN_SLP(gpf1-0, INPUT, DOWN); + PIN_SLP(gpf1-1, INPUT, DOWN); + PIN_SLP(gpf1-2, INPUT, DOWN); + PIN_SLP(gpf1-3, INPUT, DOWN); + PIN_SLP(gpf1-4, INPUT, DOWN); + PIN_SLP(gpf1-5, INPUT, DOWN); + PIN_SLP(gpf1-6, INPUT, DOWN); /* NONE on LTE model */ + PIN_SLP(gpf1-7, INPUT, DOWN); + + PIN_SLP(gpf2-0, INPUT, DOWN); + PIN_SLP(gpf2-1, INPUT, DOWN); + PIN_SLP(gpf2-2, INPUT, DOWN); /* PREV, NONE on LTE model */ + PIN_SLP(gpf2-3, INPUT, DOWN); + PIN_SLP(gpf2-4, INPUT, DOWN); + PIN_SLP(gpf2-5, INPUT, DOWN); + PIN_SLP(gpf2-6, INPUT, DOWN); + PIN_SLP(gpf2-7, INPUT, DOWN); + + PIN_SLP(gpf3-0, INPUT, DOWN); + PIN_SLP(gpf3-1, INPUT, DOWN); + PIN_SLP(gpf3-2, INPUT, DOWN); + PIN_SLP(gpf3-3, INPUT, DOWN); + PIN_SLP(gpf3-4, PREV, NONE); + PIN_SLP(gpf3-5, OUT0, DOWN); + + PIN_SLP(gpj0-0, INPUT, DOWN); + PIN_SLP(gpj0-1, INPUT, DOWN); + PIN_SLP(gpj0-2, INPUT, DOWN); + PIN_SLP(gpj0-3, OUT0, NONE); + PIN_SLP(gpj0-4, INPUT, DOWN); + PIN_SLP(gpj0-5, INPUT, DOWN); + PIN_SLP(gpj0-6, OUT0, NONE); + PIN_SLP(gpj0-7, OUT0, NONE); + + PIN_SLP(gpj1-0, OUT0, NONE); + PIN_SLP(gpj1-1, INPUT, DOWN); + PIN_SLP(gpj1-2, PREV, NONE); + PIN_SLP(gpj1-3, INPUT, DOWN); + PIN_SLP(gpj1-4, INPUT, DOWN); + }; +}; + +&pinctrl_1 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep1>; + + max77693_irq: max77693-irq { + samsung,pins = "gpx1-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + max77693_fuel_irq: max77693-fuel-irq { + samsung,pins = "gpx2-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + s5m8767_dvs: s5m8767-dvs { + samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + s5m8767_irq: s5m8767-irq { + samsung,pins = "gpx0-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + sdhci2_cd: sdhci2-cd-irq { + samsung,pins = "gpx3-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + bt_shutdown: bt-shutdown-pins { + samsung,pins = "gpl0-6"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + bt_host_wakeup: bt-host-wakeup-pins { + samsung,pins = "gpx2-6"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + bt_device_wakeup: bt-device-wakeup-pins { + samsung,pins = "gpx3-1"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + backlight_reset: backlight-reset { + samsung,pins = "gpm0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + gpio_keys: gpio-keys-pins { + samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + sleep1: sleep-state { + PIN_SLP(gpk0-0, PREV, NONE); + PIN_SLP(gpk0-1, PREV, NONE); + PIN_SLP(gpk0-2, PREV, NONE); + PIN_SLP(gpk0-3, PREV, NONE); + PIN_SLP(gpk0-4, PREV, NONE); + PIN_SLP(gpk0-5, PREV, NONE); + PIN_SLP(gpk0-6, PREV, NONE); + + PIN_SLP(gpk1-0, INPUT, DOWN); + PIN_SLP(gpk1-1, INPUT, DOWN); + PIN_SLP(gpk1-2, INPUT, DOWN); + PIN_SLP(gpk1-3, PREV, NONE); + PIN_SLP(gpk1-4, PREV, NONE); + PIN_SLP(gpk1-5, PREV, NONE); + PIN_SLP(gpk1-6, PREV, NONE); + + PIN_SLP(gpk2-0, INPUT, DOWN); + PIN_SLP(gpk2-1, INPUT, DOWN); + PIN_SLP(gpk2-2, INPUT, DOWN); + PIN_SLP(gpk2-3, INPUT, DOWN); + PIN_SLP(gpk2-4, INPUT, DOWN); + PIN_SLP(gpk2-5, INPUT, DOWN); + PIN_SLP(gpk2-6, INPUT, DOWN); + + PIN_SLP(gpk3-0, OUT0, NONE); + PIN_SLP(gpk3-1, INPUT, NONE); + PIN_SLP(gpk3-2, INPUT, DOWN); + PIN_SLP(gpk3-3, INPUT, NONE); + PIN_SLP(gpk3-4, INPUT, NONE); + PIN_SLP(gpk3-5, INPUT, NONE); + PIN_SLP(gpk3-6, INPUT, NONE); + + PIN_SLP(gpl0-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */ + PIN_SLP(gpl0-1, INPUT, NONE); + PIN_SLP(gpl0-2, INPUT, NONE); + PIN_SLP(gpl0-3, INPUT, DOWN); + PIN_SLP(gpl0-4, INPUT, DOWN); + PIN_SLP(gpl0-6, PREV, NONE); + + PIN_SLP(gpl1-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */ + PIN_SLP(gpl1-1, OUT0, NONE); + PIN_SLP(gpl2-0, INPUT, DOWN); + PIN_SLP(gpl2-1, PREV, NONE); /* INPUT, DOWN on LTE */ + PIN_SLP(gpl2-2, PREV, NONE); /* INPUT, DOWN on LTE */ + PIN_SLP(gpl2-3, INPUT, DOWN); + PIN_SLP(gpl2-4, INPUT, DOWN); /* OUT0, NONE on models with modem */ + PIN_SLP(gpl2-5, INPUT, DOWN); /* PREV, NONE on LTE */ + PIN_SLP(gpl2-6, INPUT, DOWN); + PIN_SLP(gpl2-7, INPUT, DOWN); + + PIN_SLP(gpm0-0, PREV, NONE); + PIN_SLP(gpm0-1, OUT0, NONE); + PIN_SLP(gpm0-2, INPUT, DOWN); + PIN_SLP(gpm0-3, INPUT, DOWN); + PIN_SLP(gpm0-4, INPUT, DOWN); + PIN_SLP(gpm0-5, INPUT, DOWN); + PIN_SLP(gpm0-6, INPUT, DOWN); + PIN_SLP(gpm0-7, INPUT, DOWN); + + PIN_SLP(gpm1-0, INPUT, DOWN); + PIN_SLP(gpm1-1, INPUT, DOWN); + PIN_SLP(gpm1-2, INPUT, NONE); + PIN_SLP(gpm1-3, INPUT, NONE); + PIN_SLP(gpm1-4, INPUT, NONE); + PIN_SLP(gpm1-5, INPUT, NONE); + PIN_SLP(gpm1-6, OUT0, NONE); + + PIN_SLP(gpm2-0, INPUT, NONE); + PIN_SLP(gpm2-1, INPUT, NONE); + PIN_SLP(gpm2-2, OUT0, NONE); + PIN_SLP(gpm2-3, INPUT, DOWN); + PIN_SLP(gpm2-4, INPUT, DOWN); + + PIN_SLP(gpm3-0, PREV, NONE); + PIN_SLP(gpm3-1, PREV, NONE); + PIN_SLP(gpm3-2, PREV, NONE); + PIN_SLP(gpm3-3, INPUT, DOWN); /* OUT1, NONE for 3G */ + PIN_SLP(gpm3-4, INPUT, DOWN); + PIN_SLP(gpm3-5, PREV, NONE); + PIN_SLP(gpm3-6, INPUT, DOWN); + PIN_SLP(gpm3-7, OUT0, NONE); + + PIN_SLP(gpm4-0, INPUT, DOWN); + PIN_SLP(gpm4-1, INPUT, DOWN); + PIN_SLP(gpm4-2, INPUT, DOWN); + PIN_SLP(gpm4-3, INPUT, DOWN); + PIN_SLP(gpm4-4, PREV, NONE); + PIN_SLP(gpm4-5, INPUT, NONE); + PIN_SLP(gpm4-6, INPUT, DOWN); + PIN_SLP(gpm4-7, INPUT, DOWN); + + PIN_SLP(gpy0-0, INPUT, DOWN); + PIN_SLP(gpy0-1, INPUT, DOWN); + PIN_SLP(gpy0-2, INPUT, NONE); + PIN_SLP(gpy0-3, INPUT, NONE); + PIN_SLP(gpy0-4, INPUT, DOWN); + PIN_SLP(gpy0-5, INPUT, DOWN); + + PIN_SLP(gpy1-0, INPUT, DOWN); + PIN_SLP(gpy1-1, INPUT, DOWN); + PIN_SLP(gpy1-2, INPUT, DOWN); + PIN_SLP(gpy1-3, INPUT, DOWN); + + PIN_SLP(gpy2-0, PREV, NONE); + PIN_SLP(gpy2-1, INPUT, DOWN); + PIN_SLP(gpy2-2, INPUT, NONE); + PIN_SLP(gpy2-3, INPUT, NONE); + PIN_SLP(gpy2-4, INPUT, NONE); + PIN_SLP(gpy2-5, INPUT, NONE); + + PIN_SLP(gpy3-0, INPUT, DOWN); + PIN_SLP(gpy3-1, INPUT, DOWN); + PIN_SLP(gpy3-2, INPUT, DOWN); + PIN_SLP(gpy3-3, INPUT, DOWN); + PIN_SLP(gpy3-4, INPUT, DOWN); + PIN_SLP(gpy3-5, INPUT, DOWN); + PIN_SLP(gpy3-6, INPUT, DOWN); + PIN_SLP(gpy3-7, INPUT, DOWN); + + PIN_SLP(gpy4-0, INPUT, DOWN); + PIN_SLP(gpy4-1, INPUT, DOWN); + PIN_SLP(gpy4-2, INPUT, DOWN); + PIN_SLP(gpy4-3, INPUT, DOWN); + PIN_SLP(gpy4-4, INPUT, DOWN); + PIN_SLP(gpy4-5, INPUT, DOWN); + PIN_SLP(gpy4-6, INPUT, DOWN); + PIN_SLP(gpy4-7, INPUT, DOWN); + + PIN_SLP(gpy5-0, INPUT, DOWN); + PIN_SLP(gpy5-1, INPUT, DOWN); + PIN_SLP(gpy5-2, INPUT, DOWN); + PIN_SLP(gpy5-3, INPUT, DOWN); + PIN_SLP(gpy5-4, INPUT, DOWN); + PIN_SLP(gpy5-5, INPUT, DOWN); + PIN_SLP(gpy5-6, INPUT, DOWN); + PIN_SLP(gpy5-7, INPUT, DOWN); + + PIN_SLP(gpy6-0, INPUT, DOWN); + PIN_SLP(gpy6-1, INPUT, DOWN); + PIN_SLP(gpy6-2, INPUT, DOWN); + PIN_SLP(gpy6-3, INPUT, DOWN); + PIN_SLP(gpy6-4, INPUT, DOWN); + PIN_SLP(gpy6-5, INPUT, DOWN); + PIN_SLP(gpy6-6, INPUT, DOWN); + PIN_SLP(gpy6-7, INPUT, DOWN); + }; +}; + +&pinctrl_2 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep2>; + + sleep2: sleep-state { + PIN_SLP(gpz-0, INPUT, DOWN); + PIN_SLP(gpz-1, INPUT, DOWN); + PIN_SLP(gpz-2, INPUT, DOWN); + PIN_SLP(gpz-3, INPUT, DOWN); + PIN_SLP(gpz-4, INPUT, DOWN); + PIN_SLP(gpz-5, INPUT, DOWN); + PIN_SLP(gpz-6, INPUT, DOWN); + }; +}; + +&pinctrl_3 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep3>; + + sleep3: sleep-state { + PIN_SLP(gpv0-0, INPUT, DOWN); + PIN_SLP(gpv0-1, INPUT, DOWN); + PIN_SLP(gpv0-2, INPUT, DOWN); + PIN_SLP(gpv0-3, INPUT, DOWN); + PIN_SLP(gpv0-4, INPUT, DOWN); + PIN_SLP(gpv0-5, INPUT, DOWN); + PIN_SLP(gpv0-6, INPUT, DOWN); + PIN_SLP(gpv0-7, INPUT, DOWN); + + PIN_SLP(gpv1-0, INPUT, DOWN); + PIN_SLP(gpv1-1, INPUT, DOWN); + PIN_SLP(gpv1-2, INPUT, DOWN); + PIN_SLP(gpv1-3, INPUT, DOWN); + PIN_SLP(gpv1-4, INPUT, DOWN); + PIN_SLP(gpv1-5, INPUT, DOWN); + PIN_SLP(gpv1-6, INPUT, DOWN); + PIN_SLP(gpv1-7, INPUT, DOWN); + + PIN_SLP(gpv2-0, INPUT, DOWN); + PIN_SLP(gpv2-1, INPUT, DOWN); + PIN_SLP(gpv2-2, INPUT, DOWN); + PIN_SLP(gpv2-3, INPUT, DOWN); + PIN_SLP(gpv2-4, INPUT, DOWN); + PIN_SLP(gpv2-5, INPUT, DOWN); + PIN_SLP(gpv2-6, INPUT, DOWN); + PIN_SLP(gpv2-7, INPUT, DOWN); + + PIN_SLP(gpv3-0, INPUT, DOWN); + PIN_SLP(gpv3-1, INPUT, DOWN); + PIN_SLP(gpv3-2, INPUT, DOWN); + PIN_SLP(gpv3-3, INPUT, DOWN); + PIN_SLP(gpv3-4, INPUT, DOWN); + PIN_SLP(gpv3-5, INPUT, DOWN); + PIN_SLP(gpv3-6, INPUT, DOWN); + PIN_SLP(gpv3-7, INPUT, DOWN); + + PIN_SLP(gpv4-0, INPUT, DOWN); + PIN_SLP(gpv4-1, INPUT, DOWN); + }; +}; + +&pmu_system_controller { + assigned-clocks = <&pmu_system_controller 0>; + assigned-clock-parents = <&clock CLK_XUSBXTI>; +}; + +&pwm { + pinctrl-0 = <&pwm1_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <1>; + status = "okay"; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&sdhci_2 { + bus-width = <4>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; + pinctrl-names = "default"; + vmmc-supply = <&ldo23_reg>; + status = "okay"; +}; + +&sdhci_3 { + #address-cells = <1>; + #size-cells = <0>; + non-removable; + bus-width = <4>; + + mmc-pwrseq = <&wlan_pwrseq>; + pinctrl-names = "default"; + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; + status = "okay"; + + /* BCM4334 Wi-Fi */ + brcmf: wifi@1 { + compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; + reg = <1>; + + interrupt-parent = <&gpx2>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + }; +}; + +&serial_0 { + pinctrl-0 = <&uart0_data &uart0_fctl>; + pinctrl-names = "default"; + status = "okay"; + + /* BCM4334B0 Bluetooth */ + bluetooth { + compatible = "brcm,bcm4330-bt"; + pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; + pinctrl-names = "default"; + max-speed = <3000000>; + shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; + clocks = <&s5m8767_osc S2MPS11_CLK_BT>; + }; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; + +&serial_3 { + status = "okay"; +}; + +&tmu { + vtmu-supply = <&ldo10_reg>; + status = "okay"; +};
Introduce support for the Galaxy Tab 3 8.0 series of boards: - Samsung Galaxy Tab 3 8.0 WiFi (SM-T310/lt01wifi) - Samsung Galaxy Tab 3 8.0 3G (SM-T311/lt013g) - Samsung Galaxy Tab 3 8.0 LTE (SM-T315/lt01lte) What works: - Display and backlight - Touchscreen (without touchkeys) - GPIO buttons, hall sensor - WiFi and Bluetooth - USB, fuel gauge, charging (partial) - Accelerometer and magnetometer - WiFi model only: light sensor Signed-off-by: Artur Weber <aweber.kernel@gmail.com> --- Display panel bindings are added by a separate patchset: "[PATCH 0/3] Add Samsung S6D7AA0 panel controller driver"[1] [1] https://lore.kernel.org/all/20230416131632.31673-1-aweber.kernel@gmail.com/ --- arch/arm/boot/dts/Makefile | 3 + arch/arm/boot/dts/exynos4212-tab3-3g8.dts | 30 + arch/arm/boot/dts/exynos4212-tab3-lte8.dts | 43 + arch/arm/boot/dts/exynos4212-tab3-wifi8.dts | 25 + arch/arm/boot/dts/exynos4212-tab3.dtsi | 1175 +++++++++++++++++++ 5 files changed, 1276 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4212-tab3-3g8.dts create mode 100644 arch/arm/boot/dts/exynos4212-tab3-lte8.dts create mode 100644 arch/arm/boot/dts/exynos4212-tab3-wifi8.dts create mode 100644 arch/arm/boot/dts/exynos4212-tab3.dtsi