[v4,1/2] pinctrl: qcom: Add support for i2c specific pull feature

Add support for the new i2c_pull property introduced for SM8550 setting
a I2C specific pull mode on I2C able pins. Add the bit to the SM8550
specific driver while at it.

Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---

The v3 of this specific patch is here:
https://lore.kernel.org/all/20230208081836.984673-1-abel.vesa@linaro.org/

Changes since v3:
 * changed the condition in msm_config_group_set to "arg == MSM_I2C_STRONG_PULL_UP"
   as Bjorn suggested

Changes since v2:
 * This time, this patch is sent separate w.r.t. SM8550 pinctrl driver
 * The qcom,i2c-pull is dropped, bias-pull-up with value is used instead
 * Default value for i2c pull up is 2.2kOhms and since SM8550 is the
   first one to use it, we hard code it for now
 * changed the authorship as the implementation looks entirely different now

 drivers/pinctrl/qcom/pinctrl-msm.c    | 7 +++++++
 drivers/pinctrl/qcom/pinctrl-msm.h    | 1 +
 drivers/pinctrl/qcom/pinctrl-sm8550.c | 1 +
 3 files changed, 9 insertions(+)

On Thu, Feb 09, 2023 at 09:45:09AM +0200, Abel Vesa wrote:
> Add support for the new i2c_pull property introduced for SM8550 setting
> a I2C specific pull mode on I2C able pins. Add the bit to the SM8550
> specific driver while at it.
> 
> Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

Reviewed-by: Bjorn Andersson <andersson@kernel.org>

> ---
> 
> The v3 of this specific patch is here:
> https://lore.kernel.org/all/20230208081836.984673-1-abel.vesa@linaro.org/
> 
> Changes since v3:
>  * changed the condition in msm_config_group_set to "arg == MSM_I2C_STRONG_PULL_UP"
>    as Bjorn suggested
> 
> Changes since v2:
>  * This time, this patch is sent separate w.r.t. SM8550 pinctrl driver
>  * The qcom,i2c-pull is dropped, bias-pull-up with value is used instead
>  * Default value for i2c pull up is 2.2kOhms and since SM8550 is the
>    first one to use it, we hard code it for now
>  * changed the authorship as the implementation looks entirely different now
> 
>  drivers/pinctrl/qcom/pinctrl-msm.c    | 7 +++++++
>  drivers/pinctrl/qcom/pinctrl-msm.h    | 1 +
>  drivers/pinctrl/qcom/pinctrl-sm8550.c | 1 +
>  3 files changed, 9 insertions(+)
> 
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
> index 5142c363480a..a69f93e74435 100644
> --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> @@ -310,6 +310,8 @@ static int msm_config_reg(struct msm_pinctrl *pctrl,
>  	case PIN_CONFIG_BIAS_PULL_UP:
>  		*bit = g->pull_bit;
>  		*mask = 3;
> +		if (g->i2c_pull_bit)
> +			*mask |= BIT(g->i2c_pull_bit) >> *bit;
>  		break;
>  	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
>  		*bit = g->od_bit;
> @@ -336,6 +338,7 @@ static int msm_config_reg(struct msm_pinctrl *pctrl,
>  #define MSM_KEEPER		2
>  #define MSM_PULL_UP_NO_KEEPER	2
>  #define MSM_PULL_UP		3
> +#define MSM_I2C_STRONG_PULL_UP	2200
>  
>  static unsigned msm_regval_to_drive(u32 val)
>  {
> @@ -387,6 +390,8 @@ static int msm_config_group_get(struct pinctrl_dev *pctldev,
>  	case PIN_CONFIG_BIAS_PULL_UP:
>  		if (pctrl->soc->pull_no_keeper)
>  			arg = arg == MSM_PULL_UP_NO_KEEPER;
> +		else if (arg & BIT(g->i2c_pull_bit))
> +			arg = MSM_I2C_STRONG_PULL_UP;
>  		else
>  			arg = arg == MSM_PULL_UP;
>  		if (!arg)
> @@ -467,6 +472,8 @@ static int msm_config_group_set(struct pinctrl_dev *pctldev,
>  		case PIN_CONFIG_BIAS_PULL_UP:
>  			if (pctrl->soc->pull_no_keeper)
>  				arg = MSM_PULL_UP_NO_KEEPER;
> +			else if (g->i2c_pull_bit && arg == MSM_I2C_STRONG_PULL_UP)
> +				arg = BIT(g->i2c_pull_bit) | MSM_PULL_UP;
>  			else
>  				arg = MSM_PULL_UP;
>  			break;
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm.h b/drivers/pinctrl/qcom/pinctrl-msm.h
> index 05a1209bf9ae..985eceda2517 100644
> --- a/drivers/pinctrl/qcom/pinctrl-msm.h
> +++ b/drivers/pinctrl/qcom/pinctrl-msm.h
> @@ -80,6 +80,7 @@ struct msm_pingroup {
>  
>  	unsigned pull_bit:5;
>  	unsigned drv_bit:5;
> +	unsigned i2c_pull_bit:5;
>  
>  	unsigned od_bit:5;
>  	unsigned egpio_enable:5;
> diff --git a/drivers/pinctrl/qcom/pinctrl-sm8550.c b/drivers/pinctrl/qcom/pinctrl-sm8550.c
> index 0b7db7d4054a..c9d038098f2c 100644
> --- a/drivers/pinctrl/qcom/pinctrl-sm8550.c
> +++ b/drivers/pinctrl/qcom/pinctrl-sm8550.c
> @@ -47,6 +47,7 @@
>  		.mux_bit = 2,			\
>  		.pull_bit = 0,			\
>  		.drv_bit = 6,			\
> +		.i2c_pull_bit = 13,		\
>  		.egpio_enable = 12,		\
>  		.egpio_present = 11,		\
>  		.oe_bit = 9,			\
> -- 
> 2.34.1
>

On Thu, Feb 9, 2023 at 8:45 AM Abel Vesa <abel.vesa@linaro.org> wrote:

> Add support for the new i2c_pull property introduced for SM8550 setting
> a I2C specific pull mode on I2C able pins. Add the bit to the SM8550
> specific driver while at it.
>
> Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>

Applied to the pin control tree for v6.3, I expect that Bjorn will apply
patch 2/2 to the qcom tree!

Yours,
Linus Walleij

On Thu, 9 Feb 2023 09:45:09 +0200, Abel Vesa wrote:
> Add support for the new i2c_pull property introduced for SM8550 setting
> a I2C specific pull mode on I2C able pins. Add the bit to the SM8550
> specific driver while at it.
> 
> 

Applied, thanks!

[2/2] arm64: dts: qcom: sm8550: Add bias pull up value to tlmm i2c data clk states
      commit: 4059297ed0a5adf8e5fd0bd734d702a24202c02e

Best regards,