diff mbox series

[v3,11/11] platform/x86: int3472/discrete: Get the polarity from the _DSM entry

Message ID 20221216113013.126881-12-hdegoede@redhat.com
State Superseded
Headers show
Series leds: lookup-table support + int3472/media privacy LED support | expand

Commit Message

Hans de Goede Dec. 16, 2022, 11:30 a.m. UTC 
According to:
https://github.com/intel/ipu6-drivers/blob/master/patch/int3472-support-independent-clock-and-LED-gpios-5.17%2B.patch

Bits 31-24 of the _DSM pin entry integer value codes the active-value,
that is the actual physical signal (0 or 1) which needs to be output on
the pin to turn the sensor chip on (to make it active).

So if bits 31-24 are 0 for a reset pin, then the actual value of the reset
pin needs to be 0 to take the chip out of reset. IOW in this case the reset
signal is active-high rather then the default active-low.

And if bits 31-24 are 0 for a clk-en pin then the actual value of the clk
pin needs to be 0 to enable the clk. So in this case the clk-en signal
is active-low rather then the default active-high.

IOW if bits 31-24 are 0 for a pin, then the default polarity of the pin
is inverted.

Add a check for this and also propagate this new polarity to the clock
registration.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 .../platform/x86/intel/int3472/clk_and_regulator.c  |  5 ++++-
 drivers/platform/x86/intel/int3472/common.h         |  2 +-
 drivers/platform/x86/intel/int3472/discrete.c       | 13 +++++++++++--
 3 files changed, 16 insertions(+), 4 deletions(-)

Comments

Andy Shevchenko Dec. 16, 2022, 2:57 p.m. UTC | #1 
On Fri, Dec 16, 2022 at 04:57:02PM +0200, Andy Shevchenko wrote:
> On Fri, Dec 16, 2022 at 12:30:13PM +0100, Hans de Goede wrote:

> > +	/* If bits 31-24 of the _DSM entry are all 0 then the signal is inverted */
> 
> > +	active_value = obj->integer.value >> 24;
> > +	if (!active_value)
> 
> Not sure why you need a temporary variable for this. Just use
> GENMASK()/GENMASK_ULL()?
> 
> 	if (obj->integer.value & GENMASK(31, 24));

Of course should be

	if (!(obj->integer.value & GENMASK(31, 24)))

> In this case you even don't need to repeat bit numbers in the comment.
> 
> > +		polarity ^= GPIO_ACTIVE_LOW;
diff mbox series

Patch

diff --git a/drivers/platform/x86/intel/int3472/clk_and_regulator.c b/drivers/platform/x86/intel/int3472/clk_and_regulator.c
index 15a8bff645f7..2b81066b024e 100644
--- a/drivers/platform/x86/intel/int3472/clk_and_regulator.c
+++ b/drivers/platform/x86/intel/int3472/clk_and_regulator.c
@@ -87,7 +87,7 @@  static const struct clk_ops skl_int3472_clock_ops = {
 };
 
 int skl_int3472_register_clock(struct int3472_discrete_device *int3472,
-			       struct acpi_resource_gpio *agpio)
+			       struct acpi_resource_gpio *agpio, u32 polarity)
 {
 	char *path = agpio->resource_source.string_ptr;
 	struct clk_init_data init = {
@@ -106,6 +106,9 @@  int skl_int3472_register_clock(struct int3472_discrete_device *int3472,
 		return dev_err_probe(int3472->dev, ret, "getting regulator GPIO\n");
 	}
 
+	if (polarity == GPIO_ACTIVE_LOW)
+		gpiod_toggle_active_low(int3472->clock.ena_gpio);
+
 	/* Ensure the pin is in output mode and non-active state */
 	gpiod_direction_output(int3472->clock.ena_gpio, 0);
 
diff --git a/drivers/platform/x86/intel/int3472/common.h b/drivers/platform/x86/intel/int3472/common.h
index 5ec89038ae07..4317c77e53d1 100644
--- a/drivers/platform/x86/intel/int3472/common.h
+++ b/drivers/platform/x86/intel/int3472/common.h
@@ -122,7 +122,7 @@  int skl_int3472_get_sensor_adev_and_name(struct device *dev,
 					 const char **name_ret);
 
 int skl_int3472_register_clock(struct int3472_discrete_device *int3472,
-			       struct acpi_resource_gpio *agpio);
+			       struct acpi_resource_gpio *agpio, u32 polarity);
 void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472);
 
 int skl_int3472_register_regulator(struct int3472_discrete_device *int3472,
diff --git a/drivers/platform/x86/intel/int3472/discrete.c b/drivers/platform/x86/intel/int3472/discrete.c
index b7752c2b798d..96963e30ab6c 100644
--- a/drivers/platform/x86/intel/int3472/discrete.c
+++ b/drivers/platform/x86/intel/int3472/discrete.c
@@ -220,11 +220,11 @@  static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,
 	struct int3472_discrete_device *int3472 = data;
 	struct acpi_resource_gpio *agpio;
 	union acpi_object *obj;
+	u8 active_value, type;
 	const char *err_msg;
 	const char *func;
 	u32 polarity;
 	int ret;
-	u8 type;
 
 	if (!acpi_gpio_get_io_resource(ares, &agpio))
 		return 1;
@@ -248,6 +248,15 @@  static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,
 
 	int3472_get_func_and_polarity(type, &func, &polarity);
 
+	/* If bits 31-24 of the _DSM entry are all 0 then the signal is inverted */
+	active_value = obj->integer.value >> 24;
+	if (!active_value)
+		polarity ^= GPIO_ACTIVE_LOW;
+
+	dev_dbg(int3472->dev, "%s %s pin %d active-%s\n", func,
+		agpio->resource_source.string_ptr, agpio->pin_table[0],
+		(polarity == GPIO_ACTIVE_HIGH) ? "high" : "low");
+
 	switch (type) {
 	case INT3472_GPIO_TYPE_RESET:
 	case INT3472_GPIO_TYPE_POWERDOWN:
@@ -257,7 +266,7 @@  static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,
 
 		break;
 	case INT3472_GPIO_TYPE_CLK_ENABLE:
-		ret = skl_int3472_register_clock(int3472, agpio);
+		ret = skl_int3472_register_clock(int3472, agpio, polarity);
 		if (ret)
 			err_msg = "Failed to register clock\n";