diff mbox series

[v1,1/2] i2c: loongson: add bus driver for the loongson i2c controller

Message ID 20221117075938.23379-1-zhuyinbo@loongson.cn
State New
Headers show
Series [v1,1/2] i2c: loongson: add bus driver for the loongson i2c controller | expand

Commit Message

Yinbo Zhu Nov. 17, 2022, 7:59 a.m. UTC
This bus driver supports the Loongson i2c hardware controller in the
Loongson platforms and supports to use DTS and ACPI framework to
register i2c adapter device resources.

The Loongson i2c controller supports operating frequencty is 50MHZ
and supports the maximum transmission rate is 400kbps.

Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
---
 MAINTAINERS                       |   6 +
 drivers/i2c/busses/Kconfig        |  10 +
 drivers/i2c/busses/Makefile       |   1 +
 drivers/i2c/busses/i2c-loongson.c | 569 ++++++++++++++++++++++++++++++
 4 files changed, 586 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-loongson.c

Comments

Yinbo Zhu Nov. 28, 2022, 1:13 p.m. UTC | #1
在 2022/11/17 16:44, Andy Shevchenko 写道:
> On Thu, Nov 17, 2022 at 03:59:37PM +0800, Yinbo Zhu wrote:
>> This bus driver supports the Loongson i2c hardware controller in the
>> Loongson platforms and supports to use DTS and ACPI framework to
>> register i2c adapter device resources.
>>
>> The Loongson i2c controller supports operating frequencty is 50MHZ
>> and supports the maximum transmission rate is 400kbps.
> ...
>
>> +#include <linux/acpi.h>
> Besides missed of.h (but do not add it) this one has no users (see below how).
> What you _might_ need is to have property.h to be included (seems no need).

The i2c.h had included of.h/acpi.h/property.h, and remove acpi.h

  head file.

>
>> +#include <linux/module.h>
>> +#include <linux/delay.h>
>> +#include <linux/i2c.h>
>> +#include <linux/err.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/completion.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/clk.h>
>> +#include <linux/io.h>
>> +#include <linux/slab.h>
> Can you keep it ordered?
>
> ...
>
>> +#define CTR_EN				0x80
>> +#define CTR_IEN				0x40
> BIT() ?
> (don't forget to add bits.h for that)
>
> ...
>
>> +#define CR_START			0x81
>> +#define CR_STOP				0x41
>> +#define CR_READ				0x21
>> +#define CR_WRITE			0x11
> Sounds to me like a BIT() + one specific bit to be set which should be defined
> separately.

>> +#define CR_ACK				0x8
>> +#define CR_IACK				0x1
>> +
>> +#define SR_NOACK			0x80
>> +#define SR_BUSY				0x40
>> +#define SR_AL				0x20
>> +#define SR_SLAVE_ADDRESSED		0x10
>> +#define SR_SLAVE_RW			0x8
>> +#define SR_TIP				0x2
>> +#define SR_IF				0x1
> All above seems like candidates for BIT()
>
> ...
>
>> +#define i2c_readb(addr)			readb(dev->base + addr)
>> +#define i2c_writeb(val, addr)		writeb(val, dev->base + addr)
> These are rather bad macros than useful.
> Instead, you have to pass a dev parameter and even better to have them
> as static inline helpers.
>
> Also you may consider using regmap MMIO APIs.
>
> ...
>
>> +static bool repeated_start = 1;
>> +module_param(repeated_start, bool, 0600);
>> +MODULE_PARM_DESC(repeated_start,
>> +		"Compatible with devices that support repeated start");
> We discourage people to have new module parameters in the new code. Why this
> can't be altered at run-time?
>
> ...
>> +struct loongson_i2c_dev {
>> +	spinlock_t		lock;
> Haven't checkpatch complained that lock is not documented?
>
>> +	unsigned int		suspended:1;
>> +	struct device		*dev;
>> +	void __iomem		*base;
>> +	int			irq;
>> +	u32			speed_hz;
>> +	struct completion	cmd_complete;
>> +	struct resource		*ioarea;
>> +	struct i2c_adapter	adapter;
> Also consider to check what is better to have as the first field in this data
> structure. Depending on performance and code size you may choose which one can
> go with no-op pointer arithmetics.
>
>  From code size perspective you can check with bloat-o-meter.
>
>> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
>> +	struct i2c_client	*slave;
>> +	enum loongson_i2c_slave_state	slave_state;
>> +#endif
>> +};
> ...
>
>> +static int loongson_i2c_start(
>> +		struct loongson_i2c_dev *dev, int dev_addr, int flags)
> Broken indentation.
>
>> +{
>> +	unsigned long time_left;
>> +	int retry = 5;
>> +	unsigned char addr = (dev_addr & 0x7f) << 1;
> Don't we have specific macro or helper for this?
>
>> +	addr |= (flags & I2C_M_RD) ? 1 : 0;
>> +
>> +start:
>> +	mdelay(1);
> Why?
This is a workaroud.
>
>> +	i2c_writeb(addr, LOONGSON_I2C_TXR_REG);
>> +	i2c_writeb((CR_START | CR_WRITE), LOONGSON_I2C_CR_REG);
>> +	time_left = wait_for_completion_timeout(
>> +		&dev->cmd_complete,
>> +		(&dev->adapter)->timeout);
> Broken indentation, too many parentheses (use . when it's appropriate).
> Check your entire code for these.
>
>> +	if (!time_left)
>> +		return -ETIMEDOUT;
>> +
>> +	if (i2c_readb(LOONGSON_I2C_SR_REG) & SR_NOACK) {
>> +		if (loongson_i2c_stop(dev) < 0)
>> +			return -1;
>> +
>> +		while (retry--)
>> +			goto start;
> These labels here and there make code hard to understand. Try to refactor them,
> so they will be easier to follow.
>
>> +		return 0;
>> +	}
>> +	return 1;
> What does this mean? Don't you need a specific definition, since it's not an
> error code?
>
>> +}
> ...
>
>> +	i2c_writeb(i2c_readb(LOONGSON_I2C_CR_REG) |
>> +					0x01, LOONGSON_I2C_CR_REG);
>> +	i2c_writeb(i2c_readb(LOONGSON_I2C_CTR_REG) & ~0x80,
>> +					LOONGSON_I2C_CTR_REG);
>> +	i2c_writeb(prer_val & 0xFF, LOONGSON_I2C_PRER_LO_REG);
>> +	i2c_writeb((prer_val & 0xFF00) >> 8, LOONGSON_I2C_PRER_HI_REG);
>> +	i2c_writeb(i2c_readb(LOONGSON_I2C_CTR_REG) |
>> +					0xe0, LOONGSON_I2C_CTR_REG);
> Try to avoid magic numbers. Utilize GENMASK() when it's appropriate
> (here it seems you have redundant '& 0xff{00}' stuff).
>
> ...
>
> It's already a lot of remarks and comments. This patch needs more work.
> I stopped here, only a couple additional remarks below as promised above.
>
> ...
>
>> +	ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev));
> device_set_node()
>
> ...

>> +err_iounmap:
>> +	iounmap(dev->base);
>> +err_request_irq:
>> +err_free_mem:
>> +	platform_set_drvdata(pdev, NULL);
>> +	kfree(dev);
>> +err_release_region:
>> +	release_mem_region(mem->start, resource_size(mem));
>> +
>> +	return r;
> Can you utilize devm_*() / pcim_*() APIs? Why not?
>
> ...
>
>> +		.of_match_table = of_match_ptr(loongson_i2c_id_table),
>> +		.acpi_match_table = ACPI_PTR(loongson_i2c_acpi_match),
> No of_match_ptr(), no ACPI_PTR(). You probably haven't compiled your code in
> different configuration with `make W=1 ...`.

Hi Andy,


Thanks your advice,

I had adopt it in v2 patch.

>
diff mbox series

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 62c5499e4159..e45c678eb40e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12060,6 +12060,12 @@  F:	Documentation/devicetree/bindings/gpio/loongson,ls-gpio.yaml
 F:	drivers/gpio/gpio-loongson.c
 F:	include/linux/platform_data/gpio-loongson.h
 
+LOONGSON SERIES I2C DRIVER
+M:	Yinbo Zhu <zhuyinbo@loongson.cn>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	drivers/i2c/busses/i2c-loongson.c
+
 LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
 M:	Sathya Prakash <sathya.prakash@broadcom.com>
 M:	Sreekanth Reddy <sreekanth.reddy@broadcom.com>
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index e50f9603d189..25b22b54504a 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -751,6 +751,16 @@  config I2C_KEMPLD
 	  This driver can also be built as a module. If so, the module
 	  will be called i2c-kempld.
 
+config I2C_LOONGSON
+        tristate "Loongson I2C controller"
+        depends on LOONGARCH || COMPILE_TEST
+        help
+          If you say yes to this option, support will be included for the
+          built-in I2C interface on the Loongson series Platform.
+
+          This driver can also be built as a module. If so, the module
+          will be called i2c-loongson.
+
 config I2C_LPC2K
 	tristate "I2C bus support for NXP LPC2K/LPC178x/18xx/43xx"
 	depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index e73cdb1d2b5a..28a3fd18ffaf 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -76,6 +76,7 @@  obj-$(CONFIG_I2C_IMX_LPI2C)	+= i2c-imx-lpi2c.o
 obj-$(CONFIG_I2C_IOP3XX)	+= i2c-iop3xx.o
 obj-$(CONFIG_I2C_JZ4780)	+= i2c-jz4780.o
 obj-$(CONFIG_I2C_KEMPLD)	+= i2c-kempld.o
+obj-$(CONFIG_I2C_LOONGSON)	+= i2c-loongson.o
 obj-$(CONFIG_I2C_LPC2K)		+= i2c-lpc2k.o
 obj-$(CONFIG_I2C_MESON)		+= i2c-meson.o
 obj-$(CONFIG_I2C_MICROCHIP_CORE)	+= i2c-microchip-corei2c.o
diff --git a/drivers/i2c/busses/i2c-loongson.c b/drivers/i2c/busses/i2c-loongson.c
new file mode 100644
index 000000000000..80dc15329399
--- /dev/null
+++ b/drivers/i2c/busses/i2c-loongson.c
@@ -0,0 +1,569 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Author: Yinbo Zhu <zhuyinbo@loongson.cn>
+ * Copyright (C) 2022 Loongson Technology Corporation Limited
+ */
+
+#include <linux/acpi.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/completion.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+
+#define LOONGSON_I2C_PRER_LO_REG	0x0
+#define LOONGSON_I2C_PRER_HI_REG	0x1
+#define LOONGSON_I2C_CTR_REG		0x2
+#define LOONGSON_I2C_TXR_REG		0x3
+#define LOONGSON_I2C_RXR_REG		0x3
+#define LOONGSON_I2C_CR_REG		0x4
+#define LOONGSON_I2C_SR_REG		0x4
+#define LOONGSON_I2C_BLTOP_REG		0x5
+#define LOONGSON_I2C_SADDR_REG		0x7
+
+#define CTR_EN				0x80
+#define CTR_IEN				0x40
+#define CTR_TXROK			0x90
+#define CTR_RXROK			0x88
+
+#define CR_START			0x81
+#define CR_STOP				0x41
+#define CR_READ				0x21
+#define CR_WRITE			0x11
+#define CR_ACK				0x8
+#define CR_IACK				0x1
+
+#define SR_NOACK			0x80
+#define SR_BUSY				0x40
+#define SR_AL				0x20
+#define SR_SLAVE_ADDRESSED		0x10
+#define SR_SLAVE_RW			0x8
+#define SR_TIP				0x2
+#define SR_IF				0x1
+
+#define i2c_readb(addr)			readb(dev->base + addr)
+#define i2c_writeb(val, addr)		writeb(val, dev->base + addr)
+
+static bool repeated_start = 1;
+module_param(repeated_start, bool, 0600);
+MODULE_PARM_DESC(repeated_start,
+		"Compatible with devices that support repeated start");
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+enum loongson_i2c_slave_state {
+	LOONGSON_I2C_SLAVE_STOP,
+	LOONGSON_I2C_SLAVE_START,
+	LOONGSON_I2C_SLAVE_READ_REQUESTED,
+	LOONGSON_I2C_SLAVE_READ_PROCESSED,
+	LOONGSON_I2C_SLAVE_WRITE_REQUESTED,
+	LOONGSON_I2C_SLAVE_WRITE_RECEIVED,
+};
+#endif
+
+struct loongson_i2c_dev {
+	spinlock_t		lock;
+	unsigned int		suspended:1;
+	struct device		*dev;
+	void __iomem		*base;
+	int			irq;
+	u32			speed_hz;
+	struct completion	cmd_complete;
+	struct resource		*ioarea;
+	struct i2c_adapter	adapter;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+	struct i2c_client	*slave;
+	enum loongson_i2c_slave_state	slave_state;
+#endif
+};
+
+static int loongson_i2c_stop(struct loongson_i2c_dev *dev)
+{
+	unsigned long time_left;
+
+again:
+	i2c_writeb(CR_STOP, LOONGSON_I2C_CR_REG);
+	time_left = wait_for_completion_timeout(
+			&dev->cmd_complete, (&dev->adapter)->timeout);
+	if (!time_left)
+		return -ETIMEDOUT;
+
+	while (i2c_readb(LOONGSON_I2C_SR_REG) & SR_BUSY)
+		goto again;
+
+	return 0;
+}
+
+static int loongson_i2c_start(
+		struct loongson_i2c_dev *dev, int dev_addr, int flags)
+{
+	unsigned long time_left;
+	int retry = 5;
+	unsigned char addr = (dev_addr & 0x7f) << 1;
+
+	addr |= (flags & I2C_M_RD) ? 1 : 0;
+
+start:
+	mdelay(1);
+	i2c_writeb(addr, LOONGSON_I2C_TXR_REG);
+	i2c_writeb((CR_START | CR_WRITE), LOONGSON_I2C_CR_REG);
+	time_left = wait_for_completion_timeout(
+		&dev->cmd_complete,
+		(&dev->adapter)->timeout);
+	if (!time_left)
+		return -ETIMEDOUT;
+
+	if (i2c_readb(LOONGSON_I2C_SR_REG) & SR_NOACK) {
+		if (loongson_i2c_stop(dev) < 0)
+			return -1;
+
+		while (retry--)
+			goto start;
+		return 0;
+	}
+
+	return 1;
+}
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static void loongson_i2c_slave_init(
+			struct loongson_i2c_dev *dev, u16 slave_addr)
+{
+	i2c_writeb(slave_addr & 0x7f, LOONGSON_I2C_SADDR_REG);
+
+	i2c_writeb(0xc0, LOONGSON_I2C_CTR_REG);
+}
+
+static int loongson_i2c_reg_slave(struct i2c_client *client)
+{
+	unsigned long flags;
+	struct loongson_i2c_dev *dev = i2c_get_adapdata(client->adapter);
+
+	if (dev->slave)
+		return -EINVAL;
+
+	loongson_i2c_slave_init(dev, client->addr);
+
+	dev->slave = client;
+	dev->slave_state = LOONGSON_I2C_SLAVE_STOP;
+
+	return 0;
+}
+
+static int loongson_i2c_unreg_slave(struct i2c_client *client)
+{
+	unsigned long flags;
+	struct loongson_i2c_dev *dev = i2c_get_adapdata(client->adapter);
+
+	if (!dev->slave)
+		return -EINVAL;
+
+	i2c_writeb(0xa0, LOONGSON_I2C_CTR_REG);
+
+	dev->slave = NULL;
+
+	return 0;
+}
+#endif
+
+static void loongson_i2c_reginit(struct loongson_i2c_dev *dev)
+{
+	u16 prer_val;
+	u32 pclk;
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+	if (dev->slave) {
+		loongson_i2c_slave_init(dev, dev->slave->addr);
+		return;
+	}
+#endif
+	if (!dev->speed_hz) {
+		prer_val = 0x12c;
+	} else {
+		pclk = 50000000;
+		prer_val = pclk / (5 * dev->speed_hz) - 1;
+	}
+
+	i2c_writeb(i2c_readb(LOONGSON_I2C_CR_REG) |
+					0x01, LOONGSON_I2C_CR_REG);
+	i2c_writeb(i2c_readb(LOONGSON_I2C_CTR_REG) & ~0x80,
+					LOONGSON_I2C_CTR_REG);
+	i2c_writeb(prer_val & 0xFF, LOONGSON_I2C_PRER_LO_REG);
+	i2c_writeb((prer_val & 0xFF00) >> 8, LOONGSON_I2C_PRER_HI_REG);
+	i2c_writeb(i2c_readb(LOONGSON_I2C_CTR_REG) |
+					0xe0, LOONGSON_I2C_CTR_REG);
+}
+
+static int loongson_i2c_read(
+		struct loongson_i2c_dev *dev, unsigned char *buf, int count)
+{
+	int i;
+	unsigned long time_left;
+
+	for (i = 0; i < count; i++) {
+		i2c_writeb((i == count - 1) ?
+			(CR_READ | CR_ACK) : CR_READ, LOONGSON_I2C_CR_REG);
+
+		time_left = wait_for_completion_timeout(
+				&dev->cmd_complete, (&dev->adapter)->timeout);
+		if (!time_left)
+			return -ETIMEDOUT;
+
+		buf[i] = i2c_readb(LOONGSON_I2C_RXR_REG);
+	}
+
+	return i;
+}
+
+static int loongson_i2c_write(
+		struct loongson_i2c_dev *dev, unsigned char *buf, int count)
+{
+	int i;
+	unsigned long time_left;
+
+	for (i = 0; i < count; i++) {
+		i2c_writeb(buf[i], LOONGSON_I2C_TXR_REG);
+		i2c_writeb(CR_WRITE, LOONGSON_I2C_CR_REG);
+		time_left = wait_for_completion_timeout(
+				&dev->cmd_complete, (&dev->adapter)->timeout);
+		if (!time_left)
+			return -ETIMEDOUT;
+
+		if (i2c_readb(LOONGSON_I2C_SR_REG) & SR_NOACK) {
+			if (loongson_i2c_stop(dev) < 0)
+				return -1;
+			return 0;
+		}
+	}
+
+	return i;
+}
+
+static int loongson_i2c_doxfer(
+		struct loongson_i2c_dev *dev, struct i2c_msg *msgs, int num)
+{
+	int i, err;
+	struct i2c_msg *m = msgs;
+
+	for (i = 0; i < num; i++) {
+		reinit_completion(&dev->cmd_complete);
+		err = loongson_i2c_start(dev, m->addr, m->flags);
+		if (err <= 0)
+			return err;
+
+		if ((m->flags & I2C_M_RD) &&
+			(loongson_i2c_read(dev, m->buf, m->len) < 0))
+			return -1;
+
+		if ((!(m->flags & I2C_M_RD)) &&
+			(loongson_i2c_write(dev, m->buf, m->len) < 0))
+			return -1;
+
+		++m;
+
+		if (!repeated_start && loongson_i2c_stop(dev) < 0)
+			return -1;
+	}
+
+	if (repeated_start && loongson_i2c_stop(dev) < 0)
+		return -1;
+
+	return i;
+}
+
+static int loongson_i2c_xfer(
+		struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
+{
+	int ret;
+	int retry;
+	struct loongson_i2c_dev *dev;
+
+	dev = i2c_get_adapdata(adap);
+	for (retry = 0; retry < adap->retries; retry++) {
+		ret = loongson_i2c_doxfer(dev, msgs, num);
+		if (ret != -EAGAIN)
+			return ret;
+
+		udelay(100);
+	}
+
+	return -EREMOTEIO;
+}
+
+static unsigned int loongson_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm loongson_i2c_algo = {
+	.master_xfer	= loongson_i2c_xfer,
+	.functionality	= loongson_i2c_func,
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+	.reg_slave	= loongson_i2c_reg_slave,
+	.unreg_slave	= loongson_i2c_unreg_slave,
+#endif
+};
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static bool loongson_i2c_slave_irq(struct loongson_i2c_dev *dev)
+{
+	u32 stat;
+	struct i2c_client *slave = dev->slave;
+	u8 value;
+
+	stat = i2c_readb(LOONGSON_I2C_SR_REG);
+
+	if (stat & SR_SLAVE_ADDRESSED) {
+		dev->slave_state = LOONGSON_I2C_SLAVE_START;
+		i2c_writeb(CTR_RXROK | CTR_IEN, LOONGSON_I2C_CTR_REG);
+	}
+
+	if (dev->slave_state == LOONGSON_I2C_SLAVE_STOP)
+		return IRQ_NONE;
+
+	if (dev->slave_state == LOONGSON_I2C_SLAVE_START)
+		if (stat & SR_SLAVE_RW)
+			dev->slave_state =
+				LOONGSON_I2C_SLAVE_READ_REQUESTED;
+		else
+			dev->slave_state =
+				LOONGSON_I2C_SLAVE_WRITE_REQUESTED;
+
+	if (stat & SR_NOACK)
+		dev->slave_state = LOONGSON_I2C_SLAVE_STOP;
+
+	value = i2c_readb(LOONGSON_I2C_RXR_REG);
+	switch (dev->slave_state) {
+	case LOONGSON_I2C_SLAVE_READ_REQUESTED:
+		dev->slave_state = LOONGSON_I2C_SLAVE_READ_PROCESSED;
+		i2c_slave_event(
+			slave, LOONGSON_I2C_SLAVE_READ_REQUESTED, &value);
+		i2c_writeb(value, LOONGSON_I2C_TXR_REG);
+		i2c_writeb(CTR_TXROK | CTR_IEN, LOONGSON_I2C_CTR_REG);
+		break;
+	case LOONGSON_I2C_SLAVE_READ_PROCESSED:
+		i2c_slave_event(
+			slave, LOONGSON_I2C_SLAVE_READ_PROCESSED, &value);
+		i2c_writeb(value, LOONGSON_I2C_TXR_REG);
+		i2c_writeb(CTR_TXROK | CTR_IEN, LOONGSON_I2C_CTR_REG);
+		break;
+	case LOONGSON_I2C_SLAVE_WRITE_REQUESTED:
+		dev->slave_state = LOONGSON_I2C_SLAVE_WRITE_RECEIVED;
+		i2c_slave_event(
+			slave, LOONGSON_I2C_SLAVE_WRITE_REQUESTED, &value);
+		break;
+	case LOONGSON_I2C_SLAVE_WRITE_RECEIVED:
+		i2c_slave_event(
+			slave, LOONGSON_I2C_SLAVE_WRITE_RECEIVED, &value);
+		i2c_writeb(CTR_RXROK | CTR_IEN, LOONGSON_I2C_CTR_REG);
+		break;
+	case LOONGSON_I2C_SLAVE_STOP:
+		i2c_slave_event(slave, LOONGSON_I2C_SLAVE_STOP, &value);
+		i2c_writeb(0, LOONGSON_I2C_TXR_REG);
+		i2c_writeb(CTR_TXROK | CTR_IEN, LOONGSON_I2C_CTR_REG);
+		break;
+	default:
+		dev_err(dev->dev,
+			"unhandled slave_state: %d\n", dev->slave_state);
+		break;
+	}
+
+out:
+	return IRQ_HANDLED;
+}
+#endif
+
+static irqreturn_t loongson_i2c_isr(int this_irq, void *dev_id)
+{
+	unsigned char iflag;
+	struct loongson_i2c_dev *dev = dev_id;
+
+	iflag = i2c_readb(LOONGSON_I2C_SR_REG);
+
+	if (iflag & SR_IF) {
+		i2c_writeb(CR_IACK, LOONGSON_I2C_CR_REG);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+		if (dev->slave)
+			loongson_i2c_slave_irq(dev);
+#endif
+		if (!(iflag & SR_TIP))
+			complete(&dev->cmd_complete);
+	} else
+		return IRQ_NONE;
+
+	return IRQ_HANDLED;
+}
+
+static int loongson_i2c_probe(struct platform_device *pdev)
+{
+	struct loongson_i2c_dev	*dev;
+	struct i2c_adapter	*adap;
+	struct resource		*mem, *ioarea;
+	int			r, irq;
+	u32			bus_speed;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (IS_ERR(mem))
+		return dev_err_probe(
+			&pdev->dev, PTR_ERR(mem), "no mem resource\n");
+
+	ioarea = request_mem_region(mem->start, resource_size(mem),
+			pdev->name);
+	if (IS_ERR(ioarea))
+		return dev_err_probe(&pdev->dev, PTR_ERR(ioarea),
+					"i2c region already claimed\n");
+
+	bus_speed = i2c_acpi_find_bus_speed(&pdev->dev);
+	if (!bus_speed)
+		device_property_read_u32(&pdev->dev, "clock-frequency",
+					&bus_speed);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0)
+		return dev_err_probe(&pdev->dev, irq, "no irq resource\n");
+
+	dev = kzalloc(sizeof(struct loongson_i2c_dev), GFP_KERNEL);
+	if (!dev) {
+		r = -ENOMEM;
+		goto err_release_region;
+	}
+
+	init_completion(&dev->cmd_complete);
+
+	dev->dev = &pdev->dev;
+	dev->irq = irq;
+	dev->speed_hz = bus_speed;
+	dev->base = ioremap(mem->start, resource_size(mem));
+	if (!dev->base) {
+		r = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	platform_set_drvdata(pdev, dev);
+
+	loongson_i2c_reginit(dev);
+
+	r = request_irq(
+		dev->irq, loongson_i2c_isr, IRQF_SHARED, "loongson-i2c", dev);
+	if (r) {
+		dev_err(&pdev->dev, "failed to request i2c irq %i\n", dev->irq);
+		goto err_request_irq;
+	}
+
+	adap = &dev->adapter;
+	i2c_set_adapdata(adap, dev);
+	adap->nr = pdev->id;
+	strscpy(adap->name, pdev->name, sizeof(adap->name));
+	adap->owner = THIS_MODULE;
+	adap->class = I2C_CLASS_HWMON;
+	adap->retries = 5;
+	adap->algo = &loongson_i2c_algo;
+	adap->dev.parent = &pdev->dev;
+	adap->dev.of_node = pdev->dev.of_node;
+	ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev));
+	adap->timeout = msecs_to_jiffies(100);
+
+	r = i2c_add_adapter(adap);
+	if (r) {
+		dev_err(dev->dev, "failed to add i2c adapter\n");
+		goto err_iounmap;
+	}
+
+	return 0;
+
+err_iounmap:
+	iounmap(dev->base);
+err_request_irq:
+err_free_mem:
+	platform_set_drvdata(pdev, NULL);
+	kfree(dev);
+err_release_region:
+	release_mem_region(mem->start, resource_size(mem));
+
+	return r;
+}
+
+static int loongson_i2c_remove(struct platform_device *pdev)
+{
+	struct loongson_i2c_dev	*dev = platform_get_drvdata(pdev);
+	struct resource		*mem;
+
+	platform_set_drvdata(pdev, NULL);
+	i2c_del_adapter(&dev->adapter);
+	iounmap(dev->base);
+	kfree(dev);
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(mem->start, resource_size(mem));
+
+	return 0;
+}
+
+static int loongson_i2c_suspend_noirq(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct loongson_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+
+	i2c_dev->suspended = 1;
+
+	return 0;
+}
+
+static int loongson_i2c_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct loongson_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+
+	i2c_dev->suspended = 0;
+	loongson_i2c_reginit(i2c_dev);
+
+	return 0;
+}
+
+static const struct dev_pm_ops loongson_i2c_pm_ops = {
+	.suspend_noirq	= loongson_i2c_suspend_noirq,
+	.resume		= loongson_i2c_resume,
+};
+
+static const struct of_device_id loongson_i2c_id_table[] = {
+	{.compatible = "loongson,ls2k-i2c"},
+	{.compatible = "loongson,ls7a-i2c"},
+	{}
+};
+MODULE_DEVICE_TABLE(of, loongson_i2c_id_table);
+
+static const struct acpi_device_id loongson_i2c_acpi_match[] = {
+	{"LOON0004"},
+	{}
+};
+MODULE_DEVICE_TABLE(acpi, loongson_i2c_acpi_match);
+
+static struct platform_driver loongson_i2c_driver = {
+	.driver	= {
+		.name	= "loongson-i2c",
+		.owner	= THIS_MODULE,
+		.pm	= &loongson_i2c_pm_ops,
+		.of_match_table = of_match_ptr(loongson_i2c_id_table),
+		.acpi_match_table = ACPI_PTR(loongson_i2c_acpi_match),
+	},
+	.probe		= loongson_i2c_probe,
+	.remove		= loongson_i2c_remove,
+};
+
+static int __init loongson_i2c_init_driver(void)
+{
+	return platform_driver_register(&loongson_i2c_driver);
+}
+subsys_initcall(loongson_i2c_init_driver);
+
+static void __exit loongson_i2c_exit_driver(void)
+{
+	platform_driver_unregister(&loongson_i2c_driver);
+}
+module_exit(loongson_i2c_exit_driver);
+
+MODULE_DESCRIPTION("Loongson i2c driver");
+MODULE_LICENSE("GPL");