| Message ID | 20221110133512.478831-2-krzysztof.kozlowski@linaro.org |
|---|---|
| State | Accepted |
| Commit | ec5dba73f7ba10797904cf18092d2e6975a22147 |
| Headers | show |
| Series | [v2,1/2] ASoC: dt-bindings: qcom,wsa883x: Use correct SD_N polarity | expand |
On 10/11/2022 13:35, Krzysztof Kozlowski wrote: > The shutdown GPIO is active low (SD_N), but this depends on actual board > layout. Linux drivers should only care about logical state, where high > (1) means shutdown and low (0) means do not shutdown. > > Invert the GPIO to match logical value. > > Fixes: 43b8c7dc85a1 ("ASoC: codecs: add wsa883x amplifier support") > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > > --- Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > Changes since v1: > 1. None. > --- > sound/soc/codecs/wsa883x.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/sound/soc/codecs/wsa883x.c b/sound/soc/codecs/wsa883x.c > index c7b10bbfba7e..77a7dd3cf495 100644 > --- a/sound/soc/codecs/wsa883x.c > +++ b/sound/soc/codecs/wsa883x.c > @@ -1392,7 +1392,7 @@ static int wsa883x_probe(struct sdw_slave *pdev, > } > > wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown", > - GPIOD_FLAGS_BIT_NONEXCLUSIVE); > + GPIOD_FLAGS_BIT_NONEXCLUSIVE | GPIOD_OUT_HIGH); > if (IS_ERR(wsa883x->sd_n)) { > dev_err(&pdev->dev, "Shutdown Control GPIO not found\n"); > ret = PTR_ERR(wsa883x->sd_n); > @@ -1411,7 +1411,7 @@ static int wsa883x_probe(struct sdw_slave *pdev, > pdev->prop.simple_clk_stop_capable = true; > pdev->prop.sink_dpn_prop = wsa_sink_dpn_prop; > pdev->prop.scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY; > - gpiod_direction_output(wsa883x->sd_n, 1); > + gpiod_direction_output(wsa883x->sd_n, 0); > > wsa883x->regmap = devm_regmap_init_sdw(pdev, &wsa883x_regmap_config); > if (IS_ERR(wsa883x->regmap)) {
diff --git a/sound/soc/codecs/wsa883x.c b/sound/soc/codecs/wsa883x.c index c7b10bbfba7e..77a7dd3cf495 100644 --- a/sound/soc/codecs/wsa883x.c +++ b/sound/soc/codecs/wsa883x.c @@ -1392,7 +1392,7 @@ static int wsa883x_probe(struct sdw_slave *pdev, } wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown", - GPIOD_FLAGS_BIT_NONEXCLUSIVE); + GPIOD_FLAGS_BIT_NONEXCLUSIVE | GPIOD_OUT_HIGH); if (IS_ERR(wsa883x->sd_n)) { dev_err(&pdev->dev, "Shutdown Control GPIO not found\n"); ret = PTR_ERR(wsa883x->sd_n); @@ -1411,7 +1411,7 @@ static int wsa883x_probe(struct sdw_slave *pdev, pdev->prop.simple_clk_stop_capable = true; pdev->prop.sink_dpn_prop = wsa_sink_dpn_prop; pdev->prop.scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY; - gpiod_direction_output(wsa883x->sd_n, 1); + gpiod_direction_output(wsa883x->sd_n, 0); wsa883x->regmap = devm_regmap_init_sdw(pdev, &wsa883x_regmap_config); if (IS_ERR(wsa883x->regmap)) {
The shutdown GPIO is active low (SD_N), but this depends on actual board layout. Linux drivers should only care about logical state, where high (1) means shutdown and low (0) means do not shutdown. Invert the GPIO to match logical value. Fixes: 43b8c7dc85a1 ("ASoC: codecs: add wsa883x amplifier support") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Changes since v1: 1. None. --- sound/soc/codecs/wsa883x.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)