| Message ID | 20221104131358.1025987-3-dmitry.baryshkov@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: qcom: sm8450-hdk: enable HDMI output | expand |
On 04/11/2022 14:13, Dmitry Baryshkov wrote: > Add devices tree nodes describing display hardware on SM8450: > - Display Clock Controller > - MDSS > - MDP > - two DSI controllers and DSI PHYs > > This does not provide support for DP controllers present on SM8450. > > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++- > 1 file changed, 280 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi > index 250e6b883ca3..23f989dedfdb 100644 > --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi > @@ -2401,6 +2401,282 @@ camcc: clock-controller@ade0000 { > status = "disabled"; > }; > > + mdss: mdss@ae00000 { > + compatible = "qcom,sm8450-mdss"; > + reg = <0 0x0ae00000 0 0x1000>; > + reg-names = "mdss"; > + > + /* same path used twice */ > + interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>, > + <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > + > + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; > + > + power-domains = <&dispcc MDSS_GDSC>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>; > + clock-names = "iface", "bus", "nrt_bus", "core"; > + > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + iommus = <&apps_smmu 0x2800 0x402>; > + > + status = "disabled"; > + > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mdss_mdp: mdp@ae01000 { > + compatible = "qcom,sm8450-dpu"; > + reg = <0 0x0ae01000 0 0x8f000>, > + <0 0x0aeb0000 0 0x2008>; > + reg-names = "mdp", "vbif"; > + > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>, > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + clock-names = "bus", > + "nrt_bus", > + "iface", > + "lut", > + "core", > + "vsync"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + assigned-clock-rates = <19200000>; > + > + operating-points-v2 = <&mdp_opp_table>; > + power-domains = <&rpmhpd SM8450_MMCX>; > + > + interrupt-parent = <&mdss>; > + interrupts = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&dsi0_in>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dpu_intf2_out: endpoint { > + remote-endpoint = <&dsi1_in>; > + }; > + }; > + > + }; > + > + mdp_opp_table: mdp-opp-table { > + compatible = "operating-points-v2"; > + > + opp-172000000 { > + opp-hz = /bits/ 64 <172000000>; > + required-opps = <&rpmhpd_opp_low_svs_d1>; > + }; > + > + opp-200000000 { > + opp-hz = /bits/ 64 <200000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-325000000 { > + opp-hz = /bits/ 64 <325000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-375000000 { > + opp-hz = /bits/ 64 <375000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-500000000 { > + opp-hz = /bits/ 64 <500000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + dsi0: dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; > + assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8450_MMCX>; > + > + phys = <&dsi0_phy>; > + phy-names = "dsi"; > + > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + }; > + }; > + }; > + }; > + > + dsi0_phy: dsi-phy@ae94400 { > + compatible = "qcom,dsi-phy-7nm"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + }; > + > + dsi1: dsi@ae96000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae96000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <5>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, > + <&dispcc DISP_CC_MDSS_ESC1_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; > + assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8450_MMCX>; > + > + phys = <&dsi1_phy>; > + phy-names = "dsi"; > + > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi1_in: endpoint { > + remote-endpoint = <&dpu_intf2_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi1_out: endpoint { > + }; > + }; > + }; > + }; > + > + dsi1_phy: dsi-phy@ae96400 { > + compatible = "qcom,dsi-phy-7nm"; > + reg = <0 0x0ae96400 0 0x200>, > + <0 0x0ae96600 0 0x280>, > + <0 0x0ae96900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + > + dsi_opp_table: dsi-opp-table { > + compatible = "operating-points-v2"; > + > + opp-187500000 { > + opp-hz = /bits/ 64 <187500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-358000000 { > + opp-hz = /bits/ 64 <358000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + }; > + }; > + }; > + > dispcc: clock-controller@af00000 { > compatible = "qcom,sm8450-dispcc"; > reg = <0 0x0af00000 0 0x20000>; > @@ -2408,10 +2684,10 @@ dispcc: clock-controller@af00000 { > <&rpmhcc RPMH_CXO_CLK_A>, > <&gcc GCC_DISP_AHB_CLK>, > <&sleep_clk>, > - <0>, /* dsi0 */ > - <0>, > - <0>, /* dsi1 */ > - <0>, > + <&dsi0_phy 0>, /* dsi0 */ > + <&dsi0_phy 1>, > + <&dsi1_phy 0>, /* dsi1 */ > + <&dsi1_phy 1>, I think these comments are superfluous now. Aside from that: Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Konrad > <0>, /* dp0 */ > <0>, > <0>, /* dp1 */
On 04/11/2022 09:13, Dmitry Baryshkov wrote: > Add devices tree nodes describing display hardware on SM8450: > - Display Clock Controller > - MDSS > - MDP > - two DSI controllers and DSI PHYs > > This does not provide support for DP controllers present on SM8450. > > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++- > 1 file changed, 280 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi > index 250e6b883ca3..23f989dedfdb 100644 > --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi > @@ -2401,6 +2401,282 @@ camcc: clock-controller@ade0000 { > status = "disabled"; > }; > > + mdss: mdss@ae00000 { > + compatible = "qcom,sm8450-mdss"; > + reg = <0 0x0ae00000 0 0x1000>; > + reg-names = "mdss"; > + > + /* same path used twice */ > + interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>, > + <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > + > + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; > + > + power-domains = <&dispcc MDSS_GDSC>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>; > + clock-names = "iface", "bus", "nrt_bus", "core"; > + > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + iommus = <&apps_smmu 0x2800 0x402>; > + > + status = "disabled"; Status as last property. > + > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mdss_mdp: mdp@ae01000 { Isn't this "display-controller" in the bindings and other cases? > + compatible = "qcom,sm8450-dpu"; > + reg = <0 0x0ae01000 0 0x8f000>, > + <0 0x0aeb0000 0 0x2008>; > + reg-names = "mdp", "vbif"; > + > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>, > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + clock-names = "bus", > + "nrt_bus", > + "iface", > + "lut", > + "core", > + "vsync"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + assigned-clock-rates = <19200000>; > + > + operating-points-v2 = <&mdp_opp_table>; > + power-domains = <&rpmhpd SM8450_MMCX>; > + > + interrupt-parent = <&mdss>; > + interrupts = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&dsi0_in>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dpu_intf2_out: endpoint { > + remote-endpoint = <&dsi1_in>; > + }; > + }; > + > + }; > + > + mdp_opp_table: mdp-opp-table { > + compatible = "operating-points-v2"; > + > + opp-172000000 { > + opp-hz = /bits/ 64 <172000000>; > + required-opps = <&rpmhpd_opp_low_svs_d1>; > + }; > + > + opp-200000000 { > + opp-hz = /bits/ 64 <200000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-325000000 { > + opp-hz = /bits/ 64 <325000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-375000000 { > + opp-hz = /bits/ 64 <375000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-500000000 { > + opp-hz = /bits/ 64 <500000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + dsi0: dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; > + assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8450_MMCX>; > + > + phys = <&dsi0_phy>; > + phy-names = "dsi"; > + > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + }; > + }; > + }; > + }; > + > + dsi0_phy: dsi-phy@ae94400 { You were just renaming all these to "phy" recently. > + compatible = "qcom,dsi-phy-7nm"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + }; > + > + dsi1: dsi@ae96000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae96000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <5>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, > + <&dispcc DISP_CC_MDSS_ESC1_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; > + assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8450_MMCX>; > + > + phys = <&dsi1_phy>; > + phy-names = "dsi"; > + > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi1_in: endpoint { > + remote-endpoint = <&dpu_intf2_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi1_out: endpoint { > + }; > + }; > + }; > + }; > + > + dsi1_phy: dsi-phy@ae96400 { Same here Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi index 250e6b883ca3..23f989dedfdb 100644 --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi @@ -2401,6 +2401,282 @@ camcc: clock-controller@ade0000 { status = "disabled"; }; + mdss: mdss@ae00000 { + compatible = "qcom,sm8450-mdss"; + reg = <0 0x0ae00000 0 0x1000>; + reg-names = "mdss"; + + /* same path used twice */ + interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>, + <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>; + interconnect-names = "mdp0-mem", "mdp1-mem"; + + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; + + power-domains = <&dispcc MDSS_GDSC>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "nrt_bus", "core"; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x2800 0x402>; + + status = "disabled"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + mdss_mdp: mdp@ae01000 { + compatible = "qcom,sm8450-dpu"; + reg = <0 0x0ae01000 0 0x8f000>, + <0 0x0aeb0000 0 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "bus", + "nrt_bus", + "iface", + "lut", + "core", + "vsync"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <19200000>; + + operating-points-v2 = <&mdp_opp_table>; + power-domains = <&rpmhpd SM8450_MMCX>; + + interrupt-parent = <&mdss>; + interrupts = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + + }; + + mdp_opp_table: mdp-opp-table { + compatible = "operating-points-v2"; + + opp-172000000 { + opp-hz = /bits/ 64 <172000000>; + required-opps = <&rpmhpd_opp_low_svs_d1>; + }; + + opp-200000000 { + opp-hz = /bits/ 64 <200000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-325000000 { + opp-hz = /bits/ 64 <325000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-375000000 { + opp-hz = /bits/ 64 <375000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + dsi0: dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae94000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8450_MMCX>; + + phys = <&dsi0_phy>; + phy-names = "dsi"; + + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + }; + + dsi0_phy: dsi-phy@ae94400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae94400 0 0x200>, + <0 0x0ae94600 0 0x280>, + <0 0x0ae94900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + }; + + dsi1: dsi@ae96000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae96000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <5>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, + <&dispcc DISP_CC_MDSS_ESC1_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; + assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8450_MMCX>; + + phys = <&dsi1_phy>; + phy-names = "dsi"; + + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi1_in: endpoint { + remote-endpoint = <&dpu_intf2_out>; + }; + }; + + port@1 { + reg = <1>; + dsi1_out: endpoint { + }; + }; + }; + }; + + dsi1_phy: dsi-phy@ae96400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae96400 0 0x200>, + <0 0x0ae96600 0 0x280>, + <0 0x0ae96900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + + dsi_opp_table: dsi-opp-table { + compatible = "operating-points-v2"; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-358000000 { + opp-hz = /bits/ 64 <358000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; + }; + dispcc: clock-controller@af00000 { compatible = "qcom,sm8450-dispcc"; reg = <0 0x0af00000 0 0x20000>; @@ -2408,10 +2684,10 @@ dispcc: clock-controller@af00000 { <&rpmhcc RPMH_CXO_CLK_A>, <&gcc GCC_DISP_AHB_CLK>, <&sleep_clk>, - <0>, /* dsi0 */ - <0>, - <0>, /* dsi1 */ - <0>, + <&dsi0_phy 0>, /* dsi0 */ + <&dsi0_phy 1>, + <&dsi1_phy 0>, /* dsi1 */ + <&dsi1_phy 1>, <0>, /* dp0 */ <0>, <0>, /* dp1 */
Add devices tree nodes describing display hardware on SM8450: - Display Clock Controller - MDSS - MDP - two DSI controllers and DSI PHYs This does not provide support for DP controllers present on SM8450. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++- 1 file changed, 280 insertions(+), 4 deletions(-)