deleted file mode 100644
@@ -1,195 +0,0 @@
-Qualcomm MSM8916 TLMM block
-
-This binding describes the Top Level Mode Multiplexer block found in the
-MSM8916 platform.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be "qcom,msm8916-pinctrl"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: the base address and size of the TLMM register space.
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: should specify the TLMM summary IRQ.
-
-- interrupt-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as an interrupt controller
-
-- #interrupt-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/interrupt-controller/irq.h>
-
-- gpio-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as a gpio controller
-
-- #gpio-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/gpio/gpio.h>
-
-- gpio-ranges:
- Usage: required
- Definition: see ../gpio/gpio.txt
-
-- gpio-reserved-ranges:
- Usage: optional
- Definition: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-
-PIN CONFIGURATION NODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
- Usage: required
- Value type: <string-array>
- Definition: List of gpio pins affected by the properties specified in
- this subnode. Valid pins are:
- gpio0-gpio121,
- sdc1_clk,
- sdc1_cmd,
- sdc1_data
- sdc2_clk,
- sdc2_cmd,
- sdc2_data,
- qdsd_cmd,
- qdsd_data0,
- qdsd_data1,
- qdsd_data2,
- qdsd_data3
-
-- function:
- Usage: required
- Value type: <string>
- Definition: Specify the alternative function to be configured for the
- specified pins. Functions are only valid for gpio pins.
- Valid values are:
- adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, atest_char0,
- atest_char1, atest_char2, atest_char3, atest_combodac, atest_gpsadc0,
- atest_gpsadc1, atest_tsens, atest_wlan0, atest_wlan1, backlight_en,
- bimc_dte0,bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4,
- blsp_i2c5, blsp_i2c6, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2,
- blsp_spi1_cs3, blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3,
- blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4,
- blsp_spi5, blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2,
- cam1_rst, cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c,
- cci_timer0, cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out,
- display_5v, dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us,
- ext_lpass, flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
- gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, gsm0_tx1,
- gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, ldo_en,
- ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, nav_pps, nav_tsync,
- pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, pri_mi2s_ws, prng_rosc,
- pwr_crypto_enabled_a, pwr_crypto_enabled_b, pwr_modem_enabled_a,
- pwr_modem_enabled_b, pwr_nav_enabled_a, pwr_nav_enabled_b,
- qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, qdss_ctitrig_in_b0,
- qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, qdss_ctitrig_out_a1,
- qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, qdss_traceclk_a,
- qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
- qdss_tracedata_b, reset_n, sd_card, sd_write, sec_mi2s, smb_int,
- ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm,
- wcss_wlan, webcam1_rst
-
-- bias-disable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as no pull.
-
-- bias-pull-down:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull down.
-
-- bias-pull-up:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull up.
-
-- output-high:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- high.
- Not valid for sdc pins.
-
-- output-low:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- low.
- Not valid for sdc pins.
-
-- drive-strength:
- Usage: optional
- Value type: <u32>
- Definition: Selects the drive strength for the specified pins, in mA.
- Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
-
-Example:
-
- tlmm: pinctrl@1000000 {
- compatible = "qcom,msm8916-pinctrl";
- reg = <0x1000000 0x300000>;
- interrupts = <0 208 0>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&tlmm 0 0 122>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- uart2: uart2-default {
- mux {
- pins = "gpio4", "gpio5";
- function = "blsp_uart2";
- };
-
- tx {
- pins = "gpio4";
- drive-strength = <4>;
- bias-disable;
- };
-
- rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
- };
new file mode 100644
@@ -0,0 +1,166 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8916-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm MSM8916 TLMM pin controller
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller in Qualcomm MSM8916 SoC.
+
+properties:
+ compatible:
+ const: qcom,msm8916-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 61
+
+ gpio-line-names:
+ maxItems: 122
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-msm8916-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-msm8916-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-msm8916-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-1][0-9]|12[01])$"
+ - enum: [ qdsd_clk, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
+ qdsd_data3, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk,
+ sdc2_cmd, sdc2_data ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+
+ enum: [ gpio, adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
+ atest_char0, atest_char1, atest_char2, atest_char3,
+ atest_combodac, atest_gpsadc0, atest_gpsadc1, atest_tsens,
+ atest_wlan0, atest_wlan1, backlight_en, bimc_dte0, bimc_dte1,
+ blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5,
+ blsp_i2c6, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2,
+ blsp_spi1_cs3, blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2,
+ blsp_spi2_cs3, blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2,
+ blsp_spi3_cs3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_uart1,
+ blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst, cam1_standby,
+ cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
+ cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out,
+ display_5v, dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc,
+ euro_us, ext_lpass, flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b,
+ gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b,
+ gsm0_tx0, gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0,
+ kpsns1, kpsns2, ldo_en, ldo_update, mag_int, mdp_vsync,
+ modem_tsync, m_voc, nav_pps, nav_tsync, pa_indicator, pbs0,
+ pbs1, pbs2, pri_mi2s, pri_mi2s_ws, prng_rosc,
+ pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+ pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
+ pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
+ qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
+ qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
+ qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
+ qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, reset_n,
+ sd_card, sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1,
+ uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan,
+ webcam1_rst ]
+
+ bias-pull-down: true
+ bias-pull-up: true
+ bias-disable: true
+ drive-strength: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ msmgpio: pinctrl@1000000 {
+ compatible = "qcom,msm8916-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 122>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ blsp1-uart2-sleep-state {
+ pins = "gpio4", "gpio5";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi1-default-state {
+ spi-pins {
+ pins = "gpio0", "gpio1", "gpio3";
+ function = "blsp_spi1";
+
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio2";
+ function = "gpio";
+
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+ };
Convert Qualcomm MSM8916 pin controller bindings to DT schema. Keep the parsing of pin configuration subnodes consistent with other Qualcomm schemas (children named with '-state' suffix, their children with '-pins'). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- .../bindings/pinctrl/qcom,msm8916-pinctrl.txt | 195 ------------------ .../pinctrl/qcom,msm8916-pinctrl.yaml | 166 +++++++++++++++ 2 files changed, 166 insertions(+), 195 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.yaml