new file mode 100644
@@ -0,0 +1,189 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,sdm630-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SDM630 and SDM660 TLMM pin controller
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller node in Qualcomm SDM630 and SDM660
+ SoC.
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+ compatible:
+ enum:
+ - qcom,sdm630-pinctrl
+ - qcom,sdm660-pinctrl
+
+ reg:
+ maxItems: 3
+
+ reg-names:
+ items:
+ - const: south
+ - const: center
+ - const: north
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 57
+
+ gpio-line-names:
+ maxItems: 114
+
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-sdm630-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-sdm630-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-sdm630-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-3])$"
+ - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
+ sdc2_cmd, sdc2_data ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+ enum: [ adsp_ext, agera_pll, atest_char, atest_char0, atest_char1,
+ atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1,
+ atest_tsens, atest_tsens2, atest_usb1, atest_usb10,
+ atest_usb11, atest_usb12, atest_usb13, atest_usb2, atest_usb20,
+ atest_usb21, atest_usb22, atest_usb23, audio_ref, bimc_dte0,
+ bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4,
+ blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8_a, blsp_i2c8_b,
+ blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2,
+ blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7, blsp_spi8_a,
+ blsp_spi8_b, blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1,
+ blsp_uart2, blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1,
+ blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async, cci_i2c,
+ cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, gcc_gp1,
+ gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c,
+ isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync,
+ mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte,
+ nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0,
+ phase_flag1, phase_flag10, phase_flag11, phase_flag12,
+ phase_flag13, phase_flag14, phase_flag15, phase_flag16,
+ phase_flag17, phase_flag18, phase_flag19, phase_flag2,
+ phase_flag20, phase_flag21, phase_flag22, phase_flag23,
+ phase_flag24, phase_flag25, phase_flag26, phase_flag27,
+ phase_flag28, phase_flag29, phase_flag3, phase_flag30,
+ phase_flag31, phase_flag4, phase_flag5, phase_flag6,
+ phase_flag7, phase_flag8, phase_flag9, pll_bypassnl, pll_reset,
+ pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto, pwr_modem,
+ pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a, qdss_cti1_b,
+ qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10, qdss_gpio11,
+ qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15, qdss_gpio2,
+ qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6, qdss_gpio7,
+ qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request, qspi_clk,
+ qspi_cs, qspi_data0, qspi_data1, qspi_data2, qspi_data3,
+ qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data, sp_cmu,
+ ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, uim1_clk,
+ uim1_data, uim1_present, uim1_reset, uim2_clk, uim2_data,
+ uim2_present, uim2_reset, uim_batt, vfr_1, vsense_clkout,
+ vsense_data0, vsense_data1, vsense_mode, wlan1_adc0,
+ wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
+
+ bias-disable: true
+ bias-pull-down: true
+ bias-pull-up: true
+ drive-strength: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ pinctrl@3100000 {
+ compatible = "qcom,sdm630-pinctrl";
+ reg = <0x03100000 0x400000>,
+ <0x03500000 0x400000>,
+ <0x03900000 0x400000>;
+ reg-names = "south", "center", "north";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ gpio-ranges = <&tlmm 0 0 114>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ blsp1-uart1-default-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ blsp2_uart1_default: blsp2-uart1-active-state {
+ tx-rts-pins {
+ pins = "gpio16", "gpio19";
+ function = "blsp_uart5";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx-pins {
+ pins = "gpio17";
+ function = "blsp_uart5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ cts-pins {
+ pins = "gpio18";
+ function = "blsp_uart5";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+ };
deleted file mode 100644
@@ -1,191 +0,0 @@
-Qualcomm Technologies, Inc. SDM660 TLMM block
-
-This binding describes the Top Level Mode Multiplexer block found in the
-SDM660 platform.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be "qcom,sdm660-pinctrl" or
- "qcom,sdm630-pinctrl".
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: the base address and size of the north, center and south
- TLMM tiles.
-
-- reg-names:
- Usage: required
- Value type: <stringlist>
- Definition: names for the cells of reg, must contain "north", "center"
- and "south".
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: should specify the TLMM summary IRQ.
-
-- interrupt-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as an interrupt controller
-
-- #interrupt-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/interrupt-controller/irq.h>
-
-- gpio-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as a gpio controller
-
-- gpio-ranges:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: Specifies the mapping between gpio controller and
- pin-controller pins.
-
-- #gpio-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/gpio/gpio.h>
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-
-PIN CONFIGURATION NODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
- Usage: required
- Value type: <string-array>
- Definition: List of gpio pins affected by the properties specified in
- this subnode. Valid pins are:
- gpio0-gpio113,
- Supports mux, bias and drive-strength
- sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, sdc2_data sdc1_rclk,
- Supports bias and drive-strength
-
-- function:
- Usage: required
- Value type: <string>
- Definition: Specify the alternative function to be configured for the
- specified pins. Functions are only valid for gpio pins.
- Valid values are:
- adsp_ext, agera_pll, atest_char, atest_char0, atest_char1,
- atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1,
- atest_tsens, atest_tsens2, atest_usb1, atest_usb10,
- atest_usb11, atest_usb12, atest_usb13, atest_usb2,
- atest_usb20, atest_usb21, atest_usb22, atest_usb23,
- audio_ref, bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2,
- blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7,
- blsp_i2c8_a, blsp_i2c8_b, blsp_spi1, blsp_spi2, blsp_spi3,
- blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi4, blsp_spi5,
- blsp_spi6, blsp_spi7, blsp_spi8_a, blsp_spi8_b,
- blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1, blsp_uart2,
- blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1,
- blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async,
- cci_i2c, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
- gcc_gp1, gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c,
- isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync,
- mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte,
- nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0,
- phase_flag1, phase_flag10, phase_flag11, phase_flag12,
- phase_flag13, phase_flag14, phase_flag15, phase_flag16,
- phase_flag17, phase_flag18, phase_flag19, phase_flag2,
- phase_flag20, phase_flag21, phase_flag22, phase_flag23,
- phase_flag24, phase_flag25, phase_flag26, phase_flag27,
- phase_flag28, phase_flag29, phase_flag3, phase_flag30,
- phase_flag31, phase_flag4, phase_flag5, phase_flag6,
- phase_flag7, phase_flag8, phase_flag9, pll_bypassnl,
- pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto,
- pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a,
- qdss_cti1_b, qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10,
- qdss_gpio11, qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15,
- qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6,
- qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request,
- qspi_clk, qspi_cs, qspi_data0, qspi_data1, qspi_data2,
- qspi_data3, qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data,
- sp_cmu, ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2,
- uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
- uim2_data, uim2_present, uim2_reset, uim_batt, vfr_1,
- vsense_clkout, vsense_data0, vsense_data1, vsense_mode,
- wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1
-
-- bias-disable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as no pull.
-
-- bias-pull-down:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull down.
-
-- bias-pull-up:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull up.
-
-- output-high:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- high.
- Not valid for sdc pins.
-
-- output-low:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- low.
- Not valid for sdc pins.
-
-- drive-strength:
- Usage: optional
- Value type: <u32>
- Definition: Selects the drive strength for the specified pins, in mA.
- Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
-
-Example:
-
- tlmm: pinctrl@3100000 {
- compatible = "qcom,sdm660-pinctrl";
- reg = <0x3100000 0x200000>,
- <0x3500000 0x200000>,
- <0x3900000 0x200000>;
- reg-names = "south", "center", "north";
- interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- gpio-ranges = <&tlmm 0 0 114>;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
Convert Qualcomm SDM630 and SDM660 pin controller bindings to DT schema. Keep the parsing of pin configuration subnodes consistent with other Qualcomm schemas (children named with '-state' suffix, their children with '-pins'). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- .../bindings/pinctrl/qcom,sdm630-pinctrl.yaml | 189 +++++++++++++++++ .../bindings/pinctrl/qcom,sdm660-pinctrl.txt | 191 ------------------ 2 files changed, 189 insertions(+), 191 deletions(-) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt