[v2] media: dt-bindings: ov5645: Convert OV5645 binding to a schema

From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

Convert the simple OV5645 Device Tree binding to json-schema.

The previous binding marked the below properties as required which was a
driver requirement and not the device requirement so just drop them from
the required list during the conversion.
- clock-names
- clock-frequency
- vdda-supply
- vddd-supply
- vdddo-supply
- enable-gpios
- reset-gpios

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
v1->v2
* Dropped ref to video-interface-devices.yaml#
* Dropped driver specific required items from the list
* Updated commit message
* Dropped clock-lanes and bus-type from the port and example node
* Marked data-lanes as required in port node
---
 .../devicetree/bindings/media/i2c/ov5645.txt  |  54 ---------
 .../bindings/media/i2c/ovti,ov5645.yaml       | 105 ++++++++++++++++++
 2 files changed, 105 insertions(+), 54 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5645.txt
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml

Hi Prabhakar,

Thank you for the patch.

On Fri, Sep 16, 2022 at 01:26:27PM +0100, Prabhakar wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> 
> Convert the simple OV5645 Device Tree binding to json-schema.
> 
> The previous binding marked the below properties as required which was a
> driver requirement and not the device requirement so just drop them from
> the required list during the conversion.
> - clock-names

Should we then drop clock-names completely, as there's a single clock
and there will never be more ?

> - clock-frequency
> - vdda-supply
> - vddd-supply
> - vdddo-supply

The power supplies should remain mandatory, the sensor can't operate
without them.

> - enable-gpios
> - reset-gpios

These can become optional indeed as they can be hardwired.

> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
> v1->v2
> * Dropped ref to video-interface-devices.yaml#
> * Dropped driver specific required items from the list
> * Updated commit message
> * Dropped clock-lanes and bus-type from the port and example node
> * Marked data-lanes as required in port node
> ---
>  .../devicetree/bindings/media/i2c/ov5645.txt  |  54 ---------
>  .../bindings/media/i2c/ovti,ov5645.yaml       | 105 ++++++++++++++++++
>  2 files changed, 105 insertions(+), 54 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5645.txt
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> deleted file mode 100644
> index 72ad992f77be..000000000000
> --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> +++ /dev/null
> @@ -1,54 +0,0 @@
> -* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor
> -
> -The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with
> -an active array size of 2592H x 1944V. It is programmable through a serial I2C
> -interface.
> -
> -Required Properties:
> -- compatible: Value should be "ovti,ov5645".
> -- clocks: Reference to the xclk clock.
> -- clock-names: Should be "xclk".
> -- clock-frequency: Frequency of the xclk clock.
> -- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
> -  to the hardware pin PWDNB which is physically active low.
> -- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
> -  the hardware pin RESETB.
> -- vdddo-supply: Chip digital IO regulator.
> -- vdda-supply: Chip analog regulator.
> -- vddd-supply: Chip digital core regulator.
> -
> -The device node must contain one 'port' child node for its digital output
> -video port, in accordance with the video interface bindings defined in
> -Documentation/devicetree/bindings/media/video-interfaces.txt.
> -
> -Example:
> -
> -	&i2c1 {
> -		...
> -
> -		ov5645: ov5645@3c {
> -			compatible = "ovti,ov5645";
> -			reg = <0x3c>;
> -
> -			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
> -			reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
> -			pinctrl-names = "default";
> -			pinctrl-0 = <&camera_rear_default>;
> -
> -			clocks = <&clks 200>;
> -			clock-names = "xclk";
> -			clock-frequency = <24000000>;
> -
> -			vdddo-supply = <&camera_dovdd_1v8>;
> -			vdda-supply = <&camera_avdd_2v8>;
> -			vddd-supply = <&camera_dvdd_1v2>;
> -
> -			port {
> -				ov5645_ep: endpoint {
> -					clock-lanes = <1>;
> -					data-lanes = <0 2>;
> -					remote-endpoint = <&csi0_ep>;
> -				};
> -			};
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml
> new file mode 100644
> index 000000000000..22e685729bcf
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml
> @@ -0,0 +1,105 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5645.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: OmniVision OV5645 Image Sensor Device Tree Bindings
> +
> +maintainers:
> +  - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> +
> +properties:
> +  compatible:
> +    const: ovti,ov5645
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    description: XCLK Input Clock
> +
> +  clock-names:
> +    const: xclk
> +
> +  clock-frequency:
> +    description: Frequency of the xclk clock in Hz.
> +
> +  vdda-supply:
> +    description: Analog voltage supply, 2.8 volts
> +
> +  vddd-supply:
> +    description: Digital core voltage supply, 1.5 volts
> +
> +  vdddo-supply:
> +    description: Digital I/O voltage supply, 1.8 volts
> +
> +  enable-gpios:
> +    maxItems: 1
> +    description:
> +      Reference to the GPIO connected to the PWDNB pin, if any.
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description:
> +      Reference to the GPIO connected to the RESETB pin, if any.
> +
> +  port:
> +    description: Digital Output Port
> +    $ref: /schemas/graph.yaml#/$defs/port-base
> +    additionalProperties: false
> +
> +    properties:
> +      endpoint:
> +        $ref: /schemas/media/video-interfaces.yaml#
> +        unevaluatedProperties: false
> +
> +        properties:
> +          data-lanes:
> +            minItems: 1
> +            maxItems: 2
> +            items:
> +              enum: [1, 2]
> +
> +        required:
> +          - data-lanes
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - port
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +      #include <dt-bindings/gpio/gpio.h>
> +
> +      i2c {
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +
> +          camera@3c {
> +              compatible = "ovti,ov5645";
> +              pinctrl-names = "default";
> +              pinctrl-0 = <&pinctrl_ov5645>;
> +              reg = <0x3c>;
> +              clocks = <&clks 1>;
> +              clock-names = "xclk";
> +              clock-frequency = <24000000>;
> +              vdddo-supply = <&ov5645_vdddo_1v8>; /* 1.8v */
> +              vdda-supply = <&ov5645_vdda_2v8>;  /* 2.8v */
> +              vddd-supply = <&ov5645_vddd_1v5>;  /* 1.5v */

I'd drop the comments as the voltages are listed in the label name. Up
to you.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> +              enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> +              reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> +
> +              port {
> +                  ov5645_ep: endpoint {
> +                      remote-endpoint = <&csi0_ep>;
> +                      data-lanes = <1 2>;
> +                  };
> +              };
> +          };
> +      };
> +...