| Message ID | 20220718213051.1475108-3-caleb@connolly.tech |
|---|---|
| State | New |
| Headers | show |
| Series | [1/4] Documentation: dt-bindings: arm: qcom: add google,blueline | expand |
On 18/07/2022 23:30, Caleb Connolly wrote: > From: Amit Pundir <amit.pundir@linaro.org> > > This adds an initial dts for the Blueline (Pixel 3). Supported > functionality includes display, Debug UART, UFS, USB-C (peripheral), WiFi, > Bluetooth and modem. > Thank you for your patch. There is something to discuss/improve. (...) > + volume-keys { > + compatible = "gpio-keys"; > + label = "Volume keys"; > + autorepeat; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&volume_up_gpio>; > + > + vol-up { key-vol-up (DT schema requires it now) > + label = "Volume Up"; > + linux,code = <KEY_VOLUMEUP>; > + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; > + debounce-interval = <15>; > + }; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mpss_region: memory@8e000000 { > + reg = <0 0x8e000000 0 0x9800000>; > + no-map; > + }; > + > + venus_mem: venus@97800000 { > + reg = <0 0x97800000 0 0x500000>; > + no-map; > + }; > + > + cdsp_mem: cdsp-mem@97D00000 { > + reg = <0 0x97D00000 0 0x800000>; > + no-map; > + }; > + > + mba_region: mba@98500000 { > + reg = <0 0x98500000 0 0x200000>; > + no-map; > + }; > + > + slpi_mem: slpi@98700000 { > + reg = <0 0x98700000 0 0x1400000>; > + no-map; > + }; > + > + spss_mem: spss@99B00000 { > + reg = <0 0x99B00000 0 0x100000>; > + no-map; > + }; > + > + /* rmtfs lower guard */ > + memory@f2700000 { > + reg = <0 0xf2700000 0 0x1000>; > + no-map; > + }; > + > + rmtfs_mem: memory@f2701000 { > + compatible = "qcom,rmtfs-mem"; > + reg = <0 0xf2701000 0 0x200000>; > + no-map; > + > + qcom,client-id = <1>; > + qcom,vmid = <15>; > + }; > + > + /* rmtfs upper guard */ > + memory@f2901000 { > + reg = <0 0xf2901000 0 0x1000>; > + no-map; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + }; > + > + vreg_s4a_1p8: vreg-s4a-1p8 { Please use consistent naming, so if previous was "xxx-regulator", keep similar pattern here. > + compatible = "regulator-fixed"; > + regulator-name = "vreg_s4a_1p8"; > + > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-boot-on; > + > + vin-supply = <&vph_pwr>; > + }; > +}; > + > +&adsp_pas { (...) > + > +&pm8998_gpio { > + volume_up_gpio: vol-up-active { The bindings require node name to finish with "-state" > + pins = "gpio6"; > + function = "normal"; > + input-enable; > + bias-pull-up; > + qcom,drive-strength = <0>; > + }; > + > + panel_pmgpio_pins: panel-pmgpio-active { Ditto. > + pins = "gpio2", "gpio5"; > + function = "normal"; > + input-enable; > + bias-disable; > + power-source = <0>; > + }; > +}; > + > +&pm8998_pon { > + resin { > + compatible = "qcom,pm8941-resin"; > + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + bias-pull-up; > + linux,code = <KEY_VOLUMEDOWN>; > + }; > +}; > + Best regards, Krzysztof
n Tue, 19 Jul 2022 at 03:43, Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On 19/07/2022 00:30, Caleb Connolly wrote: > > From: Amit Pundir <amit.pundir@linaro.org> > > > > This adds an initial dts for the Blueline (Pixel 3). Supported > > functionality includes display, Debug UART, UFS, USB-C (peripheral), WiFi, > > Bluetooth and modem. > > > > Bootloader compatible board and msm IDs are needed for the kernel to boot > > with Pixel3 bootloader, so those are added. > > > > GPIOs 0 through 3 and 81 through 84 are configured to not be accessible > > from the application CPUs, so we mark them as reserved to allow the Pixel 3 > > to boot. > > > > The reserved-memory locations where obtained from downstream using > > kernel logs: > > https://gist.github.com/calebccff/090d10bfac3cb9e9bd98dda30b054c96 > > > > The rmtfs region is allocated with UIO, making it technically "dynamic". > > It's address and size can be read from sysfs: > > > > blueline:/ # cat /sys/class/uio/uio0/name > > rmtfs > > at /sys/class/uio/uio0/maps/map0/addr > > 0x00000000f2701000 > > blueline:/ # cat /sys/class/uio/uio0/maps/map0/size > > 0x0000000000200000 > > > > Like the OnePlus 6, it needs 1kB reserved on either side of the rmtfs > > memory to workaround some XPU bug which would otherwise cause erroneous > > XPU violations when accessing the rmtfs_mem region. > > > > For wifi, the pixel 3 reports a board-id of 0xFF, and downstream > > only includes a single bdwlan file. The qcom,ath10k-calibration-variant > > property is set to ensure that the correct calibration data is used. > > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > [AmitP: Cherry-picked and refactored from Bjorn's db845c dts > > ("arm64: dts: qcom: Add Dragonboard 845c") https://lkml.org/lkml/2019/6/6/7] > > Signed-off-by: Amit Pundir <amit.pundir@linaro.org> > > [sumits: merged commits to add board and msm ids, gpio range reservation, > > ufs device-reset gpio and adaptation to v5.5+ changes] > > Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> > > [vinod: Add display nodes] > > Signed-off-by: Vinod Koul <vkoul@kernel.org> > > [caleb: remove db845c bits, cleanup, add reserved-memory for modem/wifi] > > Signed-off-by: Caleb Connolly <caleb@connolly.tech> > > Thanks for your patch, few minor items to improve. > > > --- > > arch/arm64/boot/dts/qcom/Makefile | 1 + > > .../boot/dts/qcom/sdm845-google-blueline.dts | 652 ++++++++++++++++++ > > 2 files changed, 653 insertions(+) > > create mode 100644 arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts > > > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > > index 2f8aec2cc6db..c151e17e6eb7 100644 > > --- a/arch/arm64/boot/dts/qcom/Makefile > > +++ b/arch/arm64/boot/dts/qcom/Makefile > > @@ -100,6 +100,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb > > dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb > > dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb > > dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb > > +dtb-$(CONFIG_ARCH_QCOM) += sdm845-google-blueline.dtb > > dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb > > dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb > > dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb > > diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts > > new file mode 100644 > > index 000000000000..dec979ad9209 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts > > @@ -0,0 +1,652 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > + > > +/dts-v1/; > > + > > +#include <dt-bindings/dma/qcom-gpi.h> > > +#include <dt-bindings/input/linux-event-codes.h> > > +#include <dt-bindings/interrupt-controller/irq.h> > > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > > + > > +#include "sdm845.dtsi" > > +#include "pm8998.dtsi" > > +#include "pmi8998.dtsi" > > + > > +/delete-node/ &mpss_region; > > +/delete-node/ &venus_mem; > > +/delete-node/ &cdsp_mem; > > +/delete-node/ &mba_region; > > +/delete-node/ &slpi_mem; > > +/delete-node/ &spss_mem; > > +/delete-node/ &rmtfs_mem; > > + > > +/ { > > + model = "Google Pixel 3"; > > + compatible = "google,blueline", "qcom,sdm845"; > > + qcom,board-id = <0x00021505 0>; > > + qcom,msm-id = <321 0x20001>; > > + > > + aliases { > > + serial0 = &uart9; > > + serial1 = &uart6; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + volume-keys { > > + compatible = "gpio-keys"; > > + label = "Volume keys"; > > + autorepeat; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&volume_up_gpio>; > > + > > + vol-up { > > + label = "Volume Up"; > > + linux,code = <KEY_VOLUMEUP>; > > + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; > > + debounce-interval = <15>; > > + }; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > These properties are already part of the sdm845.dtsi, so no need to have > them here. > > > + > > + mpss_region: memory@8e000000 { > > + reg = <0 0x8e000000 0 0x9800000>; > > + no-map; > > + }; > > + > > + venus_mem: venus@97800000 { > > + reg = <0 0x97800000 0 0x500000>; > > + no-map; > > + }; > > + > > + cdsp_mem: cdsp-mem@97D00000 { > > + reg = <0 0x97D00000 0 0x800000>; > > + no-map; > > + }; > > + > > + mba_region: mba@98500000 { > > + reg = <0 0x98500000 0 0x200000>; > > + no-map; > > + }; > > + > > + slpi_mem: slpi@98700000 { > > + reg = <0 0x98700000 0 0x1400000>; > > + no-map; > > + }; > > + > > + spss_mem: spss@99B00000 { > > + reg = <0 0x99B00000 0 0x100000>; > > + no-map; > > + }; > > + > > + /* rmtfs lower guard */ > > + memory@f2700000 { > > + reg = <0 0xf2700000 0 0x1000>; > > + no-map; > > + }; > > + > > + rmtfs_mem: memory@f2701000 { > > + compatible = "qcom,rmtfs-mem"; > > + reg = <0 0xf2701000 0 0x200000>; > > + no-map; > > + > > + qcom,client-id = <1>; > > + qcom,vmid = <15>; > > + }; > > + > > + /* rmtfs upper guard */ > > + memory@f2901000 { > > + reg = <0 0xf2901000 0 0x1000>; > > + no-map; > > + }; > > + }; > > + > > + vph_pwr: vph-pwr-regulator { > > + compatible = "regulator-fixed"; > > + regulator-name = "vph_pwr"; > > + regulator-min-microvolt = <3700000>; > > + regulator-max-microvolt = <3700000>; > > + }; > > + > > + vreg_s4a_1p8: vreg-s4a-1p8 { > > + compatible = "regulator-fixed"; > > + regulator-name = "vreg_s4a_1p8"; > > + > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-always-on; > > + regulator-boot-on; > > + > > + vin-supply = <&vph_pwr>; > > + }; > > +}; > > + > > +&adsp_pas { > > + status = "okay"; > > + > > + firmware-name = "qcom/sdm845/pixel3/adsp.mbn"; > > What about using "qcom/sdm845/blueline/adsp.mbn" instead? > > Bjorn, Amit? qcom/sdm845/blueline/adsp.mbn seems more apt. > > > +}; > > + > > +&apps_rsc { > > + pm8998-rpmh-regulators { > > + compatible = "qcom,pm8998-rpmh-regulators"; > > + qcom,pmic-id = "a"; > > + vdd-s1-supply = <&vph_pwr>; > > + vdd-s2-supply = <&vph_pwr>; > > + vdd-s3-supply = <&vph_pwr>; > > + vdd-s4-supply = <&vph_pwr>; > > + vdd-s5-supply = <&vph_pwr>; > > + vdd-s6-supply = <&vph_pwr>; > > + vdd-s7-supply = <&vph_pwr>; > > + vdd-s8-supply = <&vph_pwr>; > > + vdd-s9-supply = <&vph_pwr>; > > + vdd-s10-supply = <&vph_pwr>; > > + vdd-s11-supply = <&vph_pwr>; > > + vdd-s12-supply = <&vph_pwr>; > > + vdd-s13-supply = <&vph_pwr>; > > + vdd-l1-l27-supply = <&vreg_s7a_1p025>; > > + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; > > + vdd-l3-l11-supply = <&vreg_s7a_1p025>; > > + vdd-l4-l5-supply = <&vreg_s7a_1p025>; > > + vdd-l6-supply = <&vph_pwr>; > > + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; > > + vdd-l9-supply = <&vreg_bob>; > > + vdd-l10-l23-l25-supply = <&vreg_bob>; > > + vdd-l13-l19-l21-supply = <&vreg_bob>; > > + vdd-l16-l28-supply = <&vreg_bob>; > > + vdd-l18-l22-supply = <&vreg_bob>; > > + vdd-l20-l24-supply = <&vreg_bob>; > > + vdd-l26-supply = <&vreg_s3a_1p35>; > > + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; > > + > > + vreg_s3a_1p35: smps3 { > > + regulator-min-microvolt = <1352000>; > > + regulator-max-microvolt = <1352000>; > > + }; > > + > > + vreg_s5a_2p04: smps5 { > > + regulator-min-microvolt = <1904000>; > > + regulator-max-microvolt = <2040000>; > > + }; > > + > > + vreg_s7a_1p025: smps7 { > > + regulator-min-microvolt = <900000>; > > + regulator-max-microvolt = <1028000>; > > + }; > > + > > + vdda_mipi_dsi0_pll: > > Do we need this alias? > > > + vreg_l1a_0p875: ldo1 { > > + regulator-min-microvolt = <880000>; > > + regulator-max-microvolt = <880000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + regulator-boot-on; > > + }; > > + > > + vreg_l5a_0p8: ldo5 { > > + regulator-min-microvolt = <800000>; > > + regulator-max-microvolt = <800000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l12a_1p8: ldo12 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l7a_1p8: ldo7 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l13a_2p95: ldo13 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <2960000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l14a_1p88: ldo14 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + regulator-boot-on; > > + /* > > + * We can't properly bring the panel back if it gets turned off > > + * so keep it's regulators always on for now. > > + */ > > Any idea, what is the issue here? Do you have the datasheet for the panel? > > > + regulator-always-on; > > + }; > > + > > + vreg_l17a_1p3: ldo17 { > > + regulator-min-microvolt = <1304000>; > > + regulator-max-microvolt = <1304000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l19a_3p3: ldo19 { > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3312000>; > > + qcom,init-voltage = <3300000>; > > + qcom,initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + /* > > + * The touchscreen needs this to be 3.3v, which is apparently > > + * quite close to the hardware limit for this LDO (3.312v) > > + * It must be kept in high power mode to prevent TS brownouts > > + */ > > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l20a_2p95: ldo20 { > > + regulator-min-microvolt = <2960000>; > > + regulator-max-microvolt = <2968000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l21a_2p95: ldo21 { > > + regulator-min-microvolt = <2960000>; > > + regulator-max-microvolt = <2968000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l24a_3p075: ldo24 { > > + regulator-min-microvolt = <3088000>; > > + regulator-max-microvolt = <3088000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vreg_l25a_3p3: ldo25 { > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3312000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + }; > > + > > + vdda_mipi_dsi0_1p2: > > Do we need this alias? > > > + vreg_l26a_1p2: ldo26 { > > + regulator-min-microvolt = <1200000>; > > + regulator-max-microvolt = <1200000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + regulator-boot-on; > > + }; > > + > > + vreg_l28a_3p0: ldo28 { > > + regulator-min-microvolt = <2856000>; > > + regulator-max-microvolt = <3008000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > > + regulator-boot-on; > > + /* > > + * We can't properly bring the panel back if it gets turned off > > + * so keep it's regulators always on for now. > > + */ > > + regulator-always-on; > > + }; > > + }; > > + > > + pmi8998-rpmh-regulators { > > + compatible = "qcom,pmi8998-rpmh-regulators"; > > + qcom,pmic-id = "b"; > > + > > + vdd-bob-supply = <&vph_pwr>; > > + > > + vreg_bob: bob { > > + regulator-min-microvolt = <3312000>; > > + regulator-max-microvolt = <3600000>; > > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > > + regulator-allow-bypass; > > + }; > > + }; > > + > > + pm8005-rpmh-regulators { > > + compatible = "qcom,pm8005-rpmh-regulators"; > > + qcom,pmic-id = "c"; > > + > > + vdd-s1-supply = <&vph_pwr>; > > + vdd-s2-supply = <&vph_pwr>; > > + vdd-s3-supply = <&vph_pwr>; > > + vdd-s4-supply = <&vph_pwr>; > > + > > + vreg_s3c_0p6: smps3 { > > + regulator-min-microvolt = <600000>; > > + regulator-max-microvolt = <600000>; > > + }; > > + }; > > +}; > > + > > +&cdsp_pas { > > + status = "okay"; > > + firmware-name = "qcom/sdm845/pixel3/cdsp.mbn"; > > +}; > > + > > +&dsi0 { > > + status = "okay"; > > + vdda-supply = <&vdda_mipi_dsi0_1p2>; > > + > > + ports { > > + port@1 { > > + endpoint { > > + remote-endpoint = <&lg_sw43408_in_0>; > > + data-lanes = <0 1 2 3>; > > + }; > > + }; > > + }; > > + > > + panel@0 { > > + compatible = "lg,sw43408"; > > + reg = <0>; > > + > > + vddi-supply = <&vreg_l14a_1p88>; > > + vpnl-supply = <&vreg_l28a_3p0>; > > + > > + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; > > + > > + pinctrl-names = "default"; > > + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_pmgpio_pins>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@0 { > > + reg = <0>; > > + lg_sw43408_in_0: endpoint { > > + remote-endpoint = <&dsi0_out>; > > + }; > > + }; > > + }; > > + }; > > +}; > > + > > +&dsi0_out { > > + remote-endpoint = <&lg_sw43408_in_0>; > > + data-lanes = <0 1 2 3>; > > +}; > > + > > +&dsi0_phy { > > + status = "okay"; > > + vdds-supply = <&vdda_mipi_dsi0_pll>; > > +}; > > + > > +&gcc { > > + protected-clocks = <GCC_QSPI_CORE_CLK>, > > + <GCC_QSPI_CORE_CLK_SRC>, > > + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>; > > +}; > > + > > +&gmu { > > + status = "okay"; > > +}; > > + > > +&gpi_dma0 { > > + status = "okay"; > > +}; > > + > > +&gpu { > > + status = "okay"; > > + > > + zap-shader { > > + memory-region = <&gpu_mem>; > > + firmware-name = "qcom/sdm845/pixel3/a630_zap.mbn"; > > + }; > > +}; > > + > > +&ipa { > > + status = "okay"; > > + > > + firmware-name = "qcom/sdm845/pixel3/ipa_fws.mbn"; > > +}; > > + > > +&mss_pil { > > + status = "okay"; > > + firmware-name = "qcom/sdm845/pixel3/mba.mbn", "qcom/sdm845/pixel3/modem.mbn"; > > +}; > > + > > +&mdss { > > + status = "okay"; > > +}; > > + > > +&mdss_mdp { > > + status = "okay"; > > +}; > > Not necessary, it is a default state since the commit 4a5622c1d975 > ("arm64: dts: qcom: sdm845: Don't disable MDP explicitly") > > > + > > +&pm8998_gpio { > > + volume_up_gpio: vol-up-active { > > + pins = "gpio6"; > > + function = "normal"; > > + input-enable; > > + bias-pull-up; > > + qcom,drive-strength = <0>; > > + }; > > + > > + panel_pmgpio_pins: panel-pmgpio-active { > > + pins = "gpio2", "gpio5"; > > + function = "normal"; > > + input-enable; > > + bias-disable; > > + power-source = <0>; > > + }; > > +}; > > + > > +&pm8998_pon { > > + resin { > > + compatible = "qcom,pm8941-resin"; > > + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; > > + debounce = <15625>; > > + bias-pull-up; > > + linux,code = <KEY_VOLUMEDOWN>; > > + }; > > Please move the (disabled, labelled) resin device to pm8998.dtsi and > just add status = "okay" here. > > > +}; > > + > > +&qupv3_id_0 { > > + status = "okay"; > > +}; > > + > > +&qupv3_id_1 { > > + status = "okay"; > > +}; > > + > > +&qup_uart6_default { > > + pinmux { > > + pins = "gpio45", "gpio46", "gpio47", "gpio48"; > > + function = "qup6"; > > + }; > > + > > + cts { > > + pins = "gpio45"; > > + bias-disable; > > + }; > > + > > + rts-tx { > > + pins = "gpio46", "gpio47"; > > + drive-strength = <2>; > > + bias-disable; > > + }; > > + > > + rx { > > + pins = "gpio48"; > > + bias-pull-up; > > + }; > > +}; > > + > > +&qup_uart9_default { > > + pinconf-tx { > > + pins = "gpio4"; > > + drive-strength = <2>; > > + bias-disable; > > + }; > > + > > + pinconf-rx { > > + pins = "gpio5"; > > + drive-strength = <2>; > > + bias-pull-up; > > + }; > > +}; > > + > > +&tlmm { > > + gpio-reserved-ranges = <0 4>, <81 4>; > > + > > + panel_te_pin: panel-te { > > + mux { > > + pins = "gpio12"; > > + function = "mdp_vsync"; > > + drive-strength = <2>; > > + bias-disable; > > + input-enable; > > + }; > > + }; > > + > > + panel_reset_pins: panel-active { > > + mux { > > + pins = "gpio6", "gpio52"; > > + function = "gpio"; > > + drive-strength = <8>; > > + bias-disable = <0>; > > + }; > > + }; > > + > > + panel_suspend: panel-suspend { > > + mux { > > + pins = "gpio6", "gpio52"; > > + function = "gpio"; > > + drive-strength = <2>; > > + bias-pull-down; > > + }; > > + }; > > + > > + touchscreen_reset: ts-reset { > > + mux { > > + pins = "gpio99"; > > + function = "gpio"; > > + drive-strength = <8>; > > + bias-pull-up; > > + //output-high; > > debug, can be removed? > > > + }; > > + }; > > + > > + touchscreen_pins: ts-pins { > > + mux { > > + pins = "gpio125"; > > + function = "gpio"; > > + drive-strength = <2>; > > + bias-disable; > > + }; > > + }; > > + > > + touchscreen_i2c_pins: qup-i2c2-gpio { > > + pins = "gpio27", "gpio28"; > > + function = "gpio"; > > + > > + drive-strength = <2>; > > + bias-disable; > > + }; > > +}; > > + > > +&uart6 { > > + status = "okay"; > > + > > + bluetooth { > > + compatible = "qcom,wcn3990-bt"; > > + > > + vddio-supply = <&vreg_s4a_1p8>; > > + vddxo-supply = <&vreg_l7a_1p8>; > > + vddrf-supply = <&vreg_l17a_1p3>; > > + vddch0-supply = <&vreg_l25a_3p3>; > > + max-speed = <3200000>; > > + }; > > +}; > > + > > +&uart9 { > > + status = "okay"; > > +}; > > + > > +&usb_1 { > > + status = "okay"; > > +}; > > + > > +&usb_1_dwc3 { > > + dr_mode = "peripheral"; > > +}; > > + > > +&usb_1_hsphy { > > + status = "okay"; > > + > > + vdd-supply = <&vreg_l1a_0p875>; > > + vdda-pll-supply = <&vreg_l12a_1p8>; > > + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; > > + > > + qcom,imp-res-offset-value = <8>; > > + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; > > + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; > > + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; > > +}; > > + > > +&usb_1_qmpphy { > > + status = "okay"; > > + > > + vdda-phy-supply = <&vreg_l26a_1p2>; > > + vdda-pll-supply = <&vreg_l1a_0p875>; > > +}; > > + > > +&usb_2 { > > + status = "okay"; > > +}; > > + > > +&usb_2_dwc3 { > > + dr_mode = "host"; > > +}; > > + > > +&usb_2_hsphy { > > + status = "okay"; > > + > > + vdd-supply = <&vreg_l1a_0p875>; > > + vdda-pll-supply = <&vreg_l12a_1p8>; > > + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; > > + > > + qcom,imp-res-offset-value = <8>; > > + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; > > +}; > > + > > +&usb_2_qmpphy { > > + status = "okay"; > > + > > + vdda-phy-supply = <&vreg_l26a_1p2>; > > + vdda-pll-supply = <&vreg_l1a_0p875>; > > +}; > > + > > +&ufs_mem_hc { > > + status = "okay"; > > + > > + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; > > + > > + vcc-supply = <&vreg_l20a_2p95>; > > + vcc-max-microamp = <800000>; > > +}; > > + > > +&ufs_mem_phy { > > + status = "okay"; > > + > > + vdda-phy-supply = <&vreg_l1a_0p875>; > > + vdda-pll-supply = <&vreg_l26a_1p2>; > > +}; > > + > > +&venus { > > + status = "okay"; > > + firmware-name = "qcom/sdm845/oneplus6/venus.mbn"; > > Why are you using the oneplus6 here? > > > +}; > > + > > +&wifi { > > + status = "okay"; > > + > > + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; > > + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; > > + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; > > + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; > > + > > + qcom,snoc-host-cap-8bit-quirk; > > + qcom,ath10k-calibration-variant = "google_blueline"; > > Ideally Kalle Valo should bless this string, added him to the Cc list. > Could you please submit the board file to the ath10k (see [1] for the > description and [2] for an example). > > > [1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles > [2] > https://lore.kernel.org/ath10k/CAA8EJpphUrxr5gtW0=-tZh-DrKXmHkfFxWMvYRpTUGuCesGCbw@mail.gmail.com/T/#u > > > +}; > > > -- > With best wishes > Dmitry
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 2f8aec2cc6db..c151e17e6eb7 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -100,6 +100,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-google-blueline.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts new file mode 100644 index 000000000000..dec979ad9209 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts @@ -0,0 +1,652 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include <dt-bindings/dma/qcom-gpi.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "sdm845.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" + +/delete-node/ &mpss_region; +/delete-node/ &venus_mem; +/delete-node/ &cdsp_mem; +/delete-node/ &mba_region; +/delete-node/ &slpi_mem; +/delete-node/ &spss_mem; +/delete-node/ &rmtfs_mem; + +/ { + model = "Google Pixel 3"; + compatible = "google,blueline", "qcom,sdm845"; + qcom,board-id = <0x00021505 0>; + qcom,msm-id = <321 0x20001>; + + aliases { + serial0 = &uart9; + serial1 = &uart6; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + volume-keys { + compatible = "gpio-keys"; + label = "Volume keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_up_gpio>; + + vol-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + mpss_region: memory@8e000000 { + reg = <0 0x8e000000 0 0x9800000>; + no-map; + }; + + venus_mem: venus@97800000 { + reg = <0 0x97800000 0 0x500000>; + no-map; + }; + + cdsp_mem: cdsp-mem@97D00000 { + reg = <0 0x97D00000 0 0x800000>; + no-map; + }; + + mba_region: mba@98500000 { + reg = <0 0x98500000 0 0x200000>; + no-map; + }; + + slpi_mem: slpi@98700000 { + reg = <0 0x98700000 0 0x1400000>; + no-map; + }; + + spss_mem: spss@99B00000 { + reg = <0 0x99B00000 0 0x100000>; + no-map; + }; + + /* rmtfs lower guard */ + memory@f2700000 { + reg = <0 0xf2700000 0 0x1000>; + no-map; + }; + + rmtfs_mem: memory@f2701000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xf2701000 0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + /* rmtfs upper guard */ + memory@f2901000 { + reg = <0 0xf2901000 0 0x1000>; + no-map; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + vreg_s4a_1p8: vreg-s4a-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; +}; + +&adsp_pas { + status = "okay"; + + firmware-name = "qcom/sdm845/pixel3/adsp.mbn"; +}; + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + vdd-s13-supply = <&vph_pwr>; + vdd-l1-l27-supply = <&vreg_s7a_1p025>; + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; + vdd-l3-l11-supply = <&vreg_s7a_1p025>; + vdd-l4-l5-supply = <&vreg_s7a_1p025>; + vdd-l6-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; + vdd-l9-supply = <&vreg_bob>; + vdd-l10-l23-l25-supply = <&vreg_bob>; + vdd-l13-l19-l21-supply = <&vreg_bob>; + vdd-l16-l28-supply = <&vreg_bob>; + vdd-l18-l22-supply = <&vreg_bob>; + vdd-l20-l24-supply = <&vreg_bob>; + vdd-l26-supply = <&vreg_s3a_1p35>; + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s5a_2p04: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdda_mipi_dsi0_pll: + vreg_l1a_0p875: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + }; + + vreg_l5a_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a_2p95: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + /* + * We can't properly bring the panel back if it gets turned off + * so keep it's regulators always on for now. + */ + regulator-always-on; + }; + + vreg_l17a_1p3: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l19a_3p3: ldo19 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + qcom,init-voltage = <3300000>; + qcom,initial-mode = <RPMH_REGULATOR_MODE_HPM>; + /* + * The touchscreen needs this to be 3.3v, which is apparently + * quite close to the hardware limit for this LDO (3.312v) + * It must be kept in high power mode to prevent TS brownouts + */ + regulator-allowed-modes = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l20a_2p95: ldo20 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2968000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l21a_2p95: ldo21 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2968000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l24a_3p075: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l25a_3p3: ldo25 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_mipi_dsi0_1p2: + vreg_l26a_1p2: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + }; + + vreg_l28a_3p0: ldo28 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + /* + * We can't properly bring the panel back if it gets turned off + * so keep it's regulators always on for now. + */ + regulator-always-on; + }; + }; + + pmi8998-rpmh-regulators { + compatible = "qcom,pmi8998-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + regulator-allow-bypass; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s3c_0p6: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +&cdsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/pixel3/cdsp.mbn"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&lg_sw43408_in_0>; + data-lanes = <0 1 2 3>; + }; + }; + }; + + panel@0 { + compatible = "lg,sw43408"; + reg = <0>; + + vddi-supply = <&vreg_l14a_1p88>; + vpnl-supply = <&vreg_l28a_3p0>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_pmgpio_pins>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lg_sw43408_in_0: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&lg_sw43408_in_0>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +&gcc { + protected-clocks = <GCC_QSPI_CORE_CLK>, + <GCC_QSPI_CORE_CLK_SRC>, + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>; +}; + +&gmu { + status = "okay"; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpu { + status = "okay"; + + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sdm845/pixel3/a630_zap.mbn"; + }; +}; + +&ipa { + status = "okay"; + + firmware-name = "qcom/sdm845/pixel3/ipa_fws.mbn"; +}; + +&mss_pil { + status = "okay"; + firmware-name = "qcom/sdm845/pixel3/mba.mbn", "qcom/sdm845/pixel3/modem.mbn"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&pm8998_gpio { + volume_up_gpio: vol-up-active { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + + panel_pmgpio_pins: panel-pmgpio-active { + pins = "gpio2", "gpio5"; + function = "normal"; + input-enable; + bias-disable; + power-source = <0>; + }; +}; + +&pm8998_pon { + resin { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qup_uart6_default { + pinmux { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "qup6"; + }; + + cts { + pins = "gpio45"; + bias-disable; + }; + + rts-tx { + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio48"; + bias-pull-up; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + panel_te_pin: panel-te { + mux { + pins = "gpio12"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + }; + + panel_reset_pins: panel-active { + mux { + pins = "gpio6", "gpio52"; + function = "gpio"; + drive-strength = <8>; + bias-disable = <0>; + }; + }; + + panel_suspend: panel-suspend { + mux { + pins = "gpio6", "gpio52"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + touchscreen_reset: ts-reset { + mux { + pins = "gpio99"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + //output-high; + }; + }; + + touchscreen_pins: ts-pins { + mux { + pins = "gpio125"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + }; + + touchscreen_i2c_pins: qup-i2c2-gpio { + pins = "gpio27", "gpio28"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; +}; + +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&uart9 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "peripheral"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l26a_1p2>; + vdda-pll-supply = <&vreg_l1a_0p875>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdd-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l26a_1p2>; + vdda-pll-supply = <&vreg_l1a_0p875>; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l20a_2p95>; + vcc-max-microamp = <800000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l26a_1p2>; +}; + +&venus { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/venus.mbn"; +}; + +&wifi { + status = "okay"; + + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + + qcom,snoc-host-cap-8bit-quirk; + qcom,ath10k-calibration-variant = "google_blueline"; +};