[net-next,v2,04/35,RFC] phy: fsl: Add Lynx 10G SerDes driver

diff --git a/Documentation/driver-api/phy/index.rst b/Documentation/driver-api/phy/index.rst
index 69ba1216de72..cc7ded8b969c 100644
--- a/Documentation/driver-api/phy/index.rst
+++ b/Documentation/driver-api/phy/index.rst
@@ -7,6 +7,7 @@  Generic PHY Framework
 .. toctree::
 
    phy
+   qoriq
    samsung-usb2
 
 .. only::  subproject and html
diff --git a/Documentation/driver-api/phy/qoriq.rst b/Documentation/driver-api/phy/qoriq.rst
new file mode 100644
index 000000000000..cbc2ac9ca4aa
--- /dev/null
+++ b/Documentation/driver-api/phy/qoriq.rst
@@ -0,0 +1,93 @@ 
+.. SPDX-License-Identifier: GPL-2.0
+
+=======================
+QorIQ SerDes (Lynx 10G)
+=======================
+
+Using this phy
+--------------
+
+The general order of calls should be::
+
+    [devm_][of_]phy_get()
+    phy_init()
+    phy_power_on()
+    phy_set_mode[_ext]()
+    ...
+    phy_power_off()
+    phy_exit()
+    [[of_]phy_put()]
+
+:c:func:`phy_get` just gets (or creates) a new :c:type:`phy` with the lanes
+described in the phandle. :c:func:`phy_init` is what actually reserves the
+lanes for use. Unlike some other drivers, when the phy is created, there is no
+default protocol. :c:func:`phy_set_mode <phy_set_mode_ext>` must be called in
+order to set the protocol.
+
+Supporting SoCs
+---------------
+
+Each new SoC needs a :c:type:`struct lynx_conf <lynx_conf>` for each SerDes.
+The most important member is `modes`, which is an array of :c:type:`struct
+lynx_mode <lynx_mode>`. Each "mode" represents a configuration which can be
+programmed into a protocol control register. Modes can support multiple lanes
+(such for PCIe x2 or x4), as well as multiple protocols (such as SGMII and
+1000Base-KX). There are several helper macros to make configuring each mode
+easier. It is important that the list of modes is complete, even if not all
+protocols are supported. This lets the driver know which lanes are available,
+and which have been configured by the RCW.
+
+If a protocol is missing, add it to :c:type:`enum lynx_protocol
+<lynx_protocol>`, and to ``UNSUPPORTED_PROTOS``. If the PCCR shifts/masks for
+your protocol are missing, you will need to add them to
+:c:func:`lynx_proto_mode_mask` and :c:func:`lynx_proto_mode_shift`.
+
+For example, the configuration for SerDes1 of the LS1046A is::
+
+    static const struct lynx_mode ls1046a_modes1[] = {
+        CONF_SINGLE(1, PCIE, 0x0, 1, 0b001),
+        CONF_1000BASEKX(0, 0x8, 0, 0b001),
+        CONF_SGMII25KX(1, 0x8, 1, 0b001),
+        CONF_SGMII25KX(2, 0x8, 2, 0b001),
+        CONF_SGMII25KX(3, 0x8, 3, 0b001),
+        CONF_SINGLE(1, QSGMII, 0x9, 2, 0b001),
+        CONF_XFI(2, 0xB, 0, 0b010),
+        CONF_XFI(3, 0xB, 1, 0b001),
+    };
+
+    static const struct lynx_conf ls1046a_conf1 = {
+        .modes = ls1046a_modes1,
+        .mode_count = ARRAY_SIZE(ls1046a_modes1),
+        .lanes = 4,
+        .endian = REGMAP_ENDIAN_BIG,
+    };
+
+There is an additional set of configuration for SerDes2, which supports a
+different set of modes. Both configurations should be added to the match
+table::
+
+    { .compatible = "fsl,ls1046-serdes-1", .data = &ls1046a_conf1 },
+    { .compatible = "fsl,ls1046-serdes-2", .data = &ls1046a_conf2 },
+
+Supporting Protocols
+--------------------
+
+Each protocol is a combination of values which must be programmed into the lane
+registers. To add a new protocol, first add it to :c:type:`enum lynx_protocol
+<lynx_protocol>`. If it is in ``UNSUPPORTED_PROTOS``, remove it. Add a new
+entry to `lynx_proto_params`, and populate the appropriate fields. You may need
+to add some new members to support new fields. Modify `lynx_lookup_proto` to
+map the :c:type:`enum phy_mode <phy_mode>` to :c:type:`enum lynx_protocol
+<lynx_protocol>`. Ensure that :c:func:`lynx_proto_mode_mask` and
+:c:func:`lynx_proto_mode_shift` have been updated with support for your
+protocol.
+
+You may need to modify :c:func:`lynx_set_mode` in order to support your
+procotol. This can happen when you have added members to :c:type:`struct
+lynx_proto_params <lynx_proto_params>`. It can also happen if you have specific
+clocking requirements, or protocol-specific registers to program.
+
+Internal API Reference
+----------------------
+
+.. kernel-doc:: drivers/phy/freescale/phy-fsl-lynx-10g.c
diff --git a/MAINTAINERS b/MAINTAINERS
index ca95b1833b97..ef65e2acdb48 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7977,6 +7977,12 @@  F:	drivers/ptp/ptp_qoriq.c
 F:	drivers/ptp/ptp_qoriq_debugfs.c
 F:	include/linux/fsl/ptp_qoriq.h
 
+FREESCALE QORIQ SERDES DRIVER
+M:	Sean Anderson <sean.anderson@seco.com>
+S:	Maintained
+F:	Documentation/driver-api/phy/qoriq.rst
+F:	drivers/phy/freescale/phy-qoriq.c
+
 FREESCALE QUAD SPI DRIVER
 M:	Han Xu <han.xu@nxp.com>
 L:	linux-spi@vger.kernel.org
diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
index f9c54cd02036..857b4d123515 100644
--- a/drivers/phy/freescale/Kconfig
+++ b/drivers/phy/freescale/Kconfig
@@ -38,3 +38,22 @@  config PHY_FSL_LYNX_28G
 	  found on NXP's Layerscape platforms such as LX2160A.
 	  Used to change the protocol running on SerDes lanes at runtime.
 	  Only useful for a restricted set of Ethernet protocols.
+
+config PHY_FSL_LYNX_10G
+	tristate "Freescale Layerscale Lynx 10G SerDes support"
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  This adds support for the Lynx "SerDes" devices found on various QorIQ
+	  SoCs. There may be up to four SerDes devices on each SoC, and each
+	  device supports up to eight lanes. The SerDes is configured by default
+	  by the RCW, but this module is necessary in order to support dynamic
+	  reconfiguration (such as to support 1G and 10G ethernet on the same
+	  interface). The hardware supports a variety of protocols, including
+	  Ethernet, SATA, PCIe, and more exotic links such as Interlaken and
+	  Aurora. This driver only supports Ethernet, but it will try not to
+	  touch lanes configured for other protocols.
+
+	  If you have a QorIQ processor and want to dynamically reconfigure your
+	  SerDes, say Y. If this driver is compiled as a module, it will be
+	  named phy-qoriq.
diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
index 3518d5dbe8a7..aa4374ed217c 100644
--- a/drivers/phy/freescale/Makefile
+++ b/drivers/phy/freescale/Makefile
@@ -2,4 +2,5 @@ 
 obj-$(CONFIG_PHY_FSL_IMX8MQ_USB)	+= phy-fsl-imx8mq-usb.o
 obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY)	+= phy-fsl-imx8-mipi-dphy.o
 obj-$(CONFIG_PHY_FSL_IMX8M_PCIE)	+= phy-fsl-imx8m-pcie.o
+obj-$(CONFIG_PHY_FSL_LYNX_10G)		+= phy-fsl-lynx-10g.o
 obj-$(CONFIG_PHY_FSL_LYNX_28G)		+= phy-fsl-lynx-28g.o
diff --git a/drivers/phy/freescale/phy-fsl-lynx-10g.c b/drivers/phy/freescale/phy-fsl-lynx-10g.c
new file mode 100644
index 000000000000..480bd493fbc2
--- /dev/null
+++ b/drivers/phy/freescale/phy-fsl-lynx-10g.c
@@ -0,0 +1,1483 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Sean Anderson <sean.anderson@seco.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/math64.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/units.h>
+
+#define PLL_STRIDE	0x20
+#define PLLa(a, off)	((a) * PLL_STRIDE + (off))
+#define PLLaRSTCTL(a)	PLLa(a, 0x00)
+#define PLLaCR0(a)	PLLa(a, 0x04)
+
+#define PLLaRSTCTL_RSTREQ	BIT(31)
+#define PLLaRSTCTL_RST_DONE	BIT(30)
+#define PLLaRSTCTL_RST_ERR	BIT(29)
+#define PLLaRSTCTL_PLLRST_B	BIT(7)
+#define PLLaRSTCTL_SDRST_B	BIT(6)
+#define PLLaRSTCTL_SDEN		BIT(5)
+
+#define PLLaCR0_POFF		BIT(31)
+#define PLLaCR0_RFCLK_SEL	GENMASK(30, 28)
+#define PLLaCR0_PLL_LCK		BIT(23)
+#define PLLaCR0_FRATE_SEL	GENMASK(19, 16)
+#define PLLaCR0_DLYDIV_SEL	GENMASK(1, 0)
+
+#define PCCR_BASE	0x200
+#define PCCR_STRIDE	0x4
+#define PCCRn(n)	(PCCR_BASE + n * PCCR_STRIDE)
+
+#define PCCR0_PEXa_MASK		GENMASK(2, 0)
+#define PCCR0_PEXa_SHIFT(a)	(28 - (a) * 4)
+
+#define PCCR2_SATAa_MASK	GENMASK(2, 0)
+#define PCCR2_SATAa_SHIFT(a)	(28 - (a) * 4)
+
+#define PCCR8_SGMIIa_KX		BIT(3)
+#define PCCR8_SGMIIa_MASK	GENMASK(3, 0)
+#define PCCR8_SGMIIa_SHIFT(a)	(28 - (a) * 4)
+
+#define PCCR9_QSGMIIa_MASK	GENMASK(2, 0)
+#define PCCR9_QSGMIIa_SHIFT(a)	(28 - (a) * 4)
+
+#define PCCRB_XFIa_MASK		GENMASK(2, 0)
+#define PCCRB_XFIa_SHIFT(a)	(28 - (a) * 4)
+
+#define LANE_BASE	0x800
+#define LANE_STRIDE	0x40
+#define LNm(m, off)	(LANE_BASE + (m) * LANE_STRIDE + (off))
+#define LNmGCR0(m)	LNm(m, 0x00)
+#define LNmGCR1(m)	LNm(m, 0x04)
+#define LNmSSCR0(m)	LNm(m, 0x0C)
+#define LNmRECR0(m)	LNm(m, 0x10)
+#define LNmRECR1(m)	LNm(m, 0x14)
+#define LNmTECR0(m)	LNm(m, 0x18)
+#define LNmSSCR1(m)	LNm(m, 0x1C)
+#define LNmTTLCR0(m)	LNm(m, 0x20)
+
+#define LNmGCR0_RPLL_LES	BIT(31)
+#define LNmGCR0_RRAT_SEL	GENMASK(29, 28)
+#define LNmGCR0_TPLL_LES	BIT(27)
+#define LNmGCR0_TRAT_SEL	GENMASK(25, 24)
+#define LNmGCR0_RRST_B		BIT(22)
+#define LNmGCR0_TRST_B		BIT(21)
+#define LNmGCR0_RX_PD		BIT(20)
+#define LNmGCR0_TX_PD		BIT(19)
+#define LNmGCR0_IF20BIT_EN	BIT(18)
+#define LNmGCR0_FIRST_LANE	BIT(16)
+#define LNmGCR0_TTRM_VM_SEL	GENMASK(13, 12)
+#define LNmGCR0_PROTS		GENMASK(11, 7)
+
+#define LNmGCR0_RAT_SEL_SAME		0b00
+#define LNmGCR0_RAT_SEL_HALF		0b01
+#define LNmGCR0_RAT_SEL_QUARTER		0b10
+#define LNmGCR0_RAT_SEL_DOUBLE		0b11
+
+#define LNmGCR0_PROTS_PCIE		0b00000
+#define LNmGCR0_PROTS_SGMII		0b00001
+#define LNmGCR0_PROTS_SATA		0b00010
+#define LNmGCR0_PROTS_XFI		0b01010
+
+#define LNmGCR1_RDAT_INV	BIT(31)
+#define LNmGCR1_TDAT_INV	BIT(30)
+#define LNmGCR1_OPAD_CTL	BIT(26)
+#define LNmGCR1_REIDL_TH	GENMASK(22, 20)
+#define LNmGCR1_REIDL_EX_SEL	GENMASK(19, 18)
+#define LNmGCR1_REIDL_ET_SEL	GENMASK(17, 16)
+#define LNmGCR1_REIDL_EX_MSB	BIT(15)
+#define LNmGCR1_REIDL_ET_MSB	BIT(14)
+#define LNmGCR1_REQ_CTL_SNP	BIT(13)
+#define LNmGCR1_REQ_CDR_SNP	BIT(12)
+#define LNmGCR1_TRSTDIR		BIT(7)
+#define LNmGCR1_REQ_BIN_SNP	BIT(6)
+#define LNmGCR1_ISLEW_RCTL	GENMASK(5, 4)
+#define LNmGCR1_OSLEW_RCTL	GENMASK(1, 0)
+
+#define LNmRECR0_GK2OVD		GENMASK(27, 24)
+#define LNmRECR0_GK3OVD		GENMASK(19, 16)
+#define LNmRECR0_GK2OVD_EN	BIT(15)
+#define LNmRECR0_GK3OVD_EN	BIT(16)
+#define LNmRECR0_BASE_WAND	GENMASK(11, 10)
+#define LNmRECR0_OSETOVD	GENMASK(5, 0)
+
+#define LNmRECR0_BASE_WAND_OFF		0b00
+#define LNmRECR0_BASE_WAND_DEFAULT	0b01
+#define LNmRECR0_BASE_WAND_ALTERNATE	0b10
+#define LNmRECR0_BASE_WAND_OSETOVD	0b11
+
+#define LNmTECR0_TEQ_TYPE	GENMASK(29, 28)
+#define LNmTECR0_SGN_PREQ	BIT(26)
+#define LNmTECR0_RATIO_PREQ	GENMASK(25, 22)
+#define LNmTECR0_SGN_POST1Q	BIT(21)
+#define LNmTECR0_RATIO_PST1Q	GENMASK(20, 16)
+#define LNmTECR0_ADPT_EQ	GENMASK(13, 8)
+#define LNmTECR0_AMP_RED	GENMASK(5, 0)
+
+#define LNmTECR0_TEQ_TYPE_NONE		0b00
+#define LNmTECR0_TEQ_TYPE_PRE		0b01
+#define LNmTECR0_TEQ_TYPE_BOTH		0b10
+
+#define LNmTTLCR0_FLT_SEL	GENMASK(29, 24)
+
+#define PCS_STRIDE	0x10
+#define CR_STRIDE	0x4
+#define PCSa(a, base, cr)	(base + (a) * PCS_STRIDE + (cr) * CR_STRIDE)
+
+#define PCSaCR1_MDEV_PORT	GENMASK(31, 27)
+
+#define SGMII_BASE	0x1800
+#define SGMIIaCR1(a)	PCSa(a, SGMII_BASE, 1)
+
+#define SGMIIaCR1_SGPCS_EN	BIT(11)
+
+#define QSGMII_OFFSET	0x1880
+#define QSGMIIaCR1(a)	PCSa(a, QSGMII_BASE, 1)
+
+#define XFI_OFFSET	0x1980
+#define XFIaCR1(a)	PCSa(a, XFI_BASE, 1)
+
+/* The maximum number of lanes in a single serdes */
+#define MAX_LANES	8
+
+enum lynx_protocol {
+	LYNX_PROTO_NONE = 0,
+	LYNX_PROTO_SGMII,
+	LYNX_PROTO_SGMII25,
+	LYNX_PROTO_1000BASEKX,
+	LYNX_PROTO_QSGMII,
+	LYNX_PROTO_XFI,
+	LYNX_PROTO_10GKR,
+	LYNX_PROTO_PCIE, /* Not implemented */
+	LYNX_PROTO_SATA, /* Not implemented */
+	LYNX_PROTO_LAST,
+};
+
+static const char lynx_proto_str[][16] = {
+	[LYNX_PROTO_NONE] = "unknown",
+	[LYNX_PROTO_SGMII] = "SGMII",
+	[LYNX_PROTO_SGMII25] = "2.5G SGMII",
+	[LYNX_PROTO_1000BASEKX] = "1000Base-KX",
+	[LYNX_PROTO_QSGMII] = "QSGMII",
+	[LYNX_PROTO_XFI] = "XFI",
+	[LYNX_PROTO_10GKR] = "10GBase-KR",
+	[LYNX_PROTO_PCIE] = "PCIe",
+	[LYNX_PROTO_SATA] = "SATA",
+};
+
+#define PROTO_MASK(proto) BIT(LYNX_PROTO_##proto)
+#define UNSUPPORTED_PROTOS (PROTO_MASK(SATA) | PROTO_MASK(PCIE))
+
+/**
+ * struct lynx_proto_params - Parameters for configuring a protocol
+ * @frate_khz: The PLL rate, in kHz
+ * @rat_sel: The divider to get the line rate
+ * @if20bit: Whether the proto is 20 bits or 10 bits
+ * @prots: Lane protocol select
+ * @reidl_th: Receiver electrical idle detection threshold
+ * @reidl_ex: Exit electrical idle filter
+ * @reidl_et: Enter idle filter
+ * @slew: Slew control
+ * @baseline_wander: Enable baseline wander correction
+ * @gain: Adaptive equalization gain override
+ * @offset_override: Adaptive equalization offset override
+ * @teq: Transmit equalization type (none, precursor, or precursor and
+ *       postcursor). The next few values are only used for appropriate
+ *       equalization types.
+ * @preq_ratio: Ratio of full swing transition bit to pre-cursor
+ * @postq_ratio: Ratio of full swing transition bit to first post-cursor.
+ * @adpt_eq: Transmitter Adjustments for 8G/10G
+ * @amp_red: Overall TX Amplitude Reduction
+ * @flt_sel: TTL configuration selector
+ */
+struct lynx_proto_params {
+	u32 frate_khz;
+	u8 rat_sel;
+	u8 prots;
+	u8 reidl_th;
+	u8 reidl_ex;
+	u8 reidl_et;
+	u8 slew;
+	u8 gain;
+	u8 baseline_wander;
+	u8 offset_override;
+	u8 teq;
+	u8 preq_ratio;
+	u8 postq_ratio;
+	u8 adpt_eq;
+	u8 amp_red;
+	u8 flt_sel;
+	bool if20bit;
+};
+
+static const struct lynx_proto_params lynx_proto_params[] = {
+	[LYNX_PROTO_SGMII] = {
+		.frate_khz = 5000000,
+		.rat_sel = LNmGCR0_RAT_SEL_QUARTER,
+		.if20bit = false,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.reidl_th = 0b001,
+		.reidl_ex = 0b011,
+		.reidl_et = 0b100,
+		.slew = 0b01,
+		.gain = 0b1111,
+		.offset_override = 0b0011111,
+		.teq = LNmTECR0_TEQ_TYPE_NONE,
+		.adpt_eq = 0b110000,
+		.amp_red = 0b000110,
+		.flt_sel = 0b111001,
+	},
+	[LYNX_PROTO_1000BASEKX] = {
+		.frate_khz = 5000000,
+		.rat_sel = LNmGCR0_RAT_SEL_QUARTER,
+		.if20bit = false,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.slew = 0b01,
+		.gain = 0b1111,
+		.offset_override = 0b0011111,
+		.teq = LNmTECR0_TEQ_TYPE_NONE,
+		.adpt_eq = 0b110000,
+		.flt_sel = 0b111001,
+	},
+	[LYNX_PROTO_SGMII25] = {
+		.frate_khz = 3125000,
+		.rat_sel = LNmGCR0_RAT_SEL_SAME,
+		.if20bit = false,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.slew = 0b10,
+		.offset_override = 0b0011111,
+		.teq = LNmTECR0_TEQ_TYPE_PRE,
+		.postq_ratio = 0b00110,
+		.adpt_eq = 0b110000,
+	},
+	[LYNX_PROTO_QSGMII] = {
+		.frate_khz = 5000000,
+		.rat_sel = LNmGCR0_RAT_SEL_SAME,
+		.if20bit = true,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.slew = 0b01,
+		.offset_override = 0b0011111,
+		.teq = LNmTECR0_TEQ_TYPE_PRE,
+		.postq_ratio = 0b00110,
+		.adpt_eq = 0b110000,
+		.amp_red = 0b000010,
+	},
+	[LYNX_PROTO_XFI] = {
+		.frate_khz = 5156250,
+		.rat_sel = LNmGCR0_RAT_SEL_DOUBLE,
+		.if20bit = true,
+		.prots = LNmGCR0_PROTS_XFI,
+		.slew = 0b01,
+		.baseline_wander = LNmRECR0_BASE_WAND_DEFAULT,
+		.offset_override = 0b1011111,
+		.teq = LNmTECR0_TEQ_TYPE_PRE,
+		.postq_ratio = 0b00011,
+		.adpt_eq = 0b110000,
+		.amp_red = 0b000111,
+	},
+	[LYNX_PROTO_10GKR] = {
+		.frate_khz = 5156250,
+		.rat_sel = LNmGCR0_RAT_SEL_DOUBLE,
+		.prots = LNmGCR0_PROTS_XFI,
+		.slew = 0b01,
+		.baseline_wander = LNmRECR0_BASE_WAND_DEFAULT,
+		.offset_override = 0b1011111,
+		.teq = LNmTECR0_TEQ_TYPE_BOTH,
+		.preq_ratio = 0b0011,
+		.postq_ratio = 0b01100,
+		.adpt_eq = 0b110000,
+	},
+};
+
+/**
+ * struct lynx_mode - A single configuration of a protocol controller
+ * @protos: A bitmask of the &enum lynx_protocol this mode supports
+ * @lanes: A bitmask of the lanes which will be used when this config is
+ *         selected
+ * @pccr: The number of the PCCR which contains this mode
+ * @idx: The index of the protocol controller. For example, SGMIIB would have
+ *       index 1.
+ * @cfg: The value to program into the controller to select this mode
+ *
+ * The serdes has multiple protocol controllers which can be each be selected
+ * independently. Depending on their configuration, they may use multiple lanes
+ * at once (e.g. AUI or PCIe x4). Additionally, multiple protocols may be
+ * supported by a single mode (XFI and 10GKR differ only in their protocol
+ * parameters).
+ */
+struct lynx_mode {
+	u16 protos;
+	u8 lanes;
+	u8 pccr;
+	u8 idx;
+	u8 cfg;
+};
+
+static_assert(LYNX_PROTO_LAST - 1 <=
+	      sizeof_field(struct lynx_mode, protos) * BITS_PER_BYTE);
+static_assert(MAX_LANES <=
+	      sizeof_field(struct lynx_mode, lanes) * BITS_PER_BYTE);
+
+#define CONF(_lanes, _protos, _pccr, _idx, _cfg) { \
+	.lanes = _lanes, \
+	.protos = _protos, \
+	.pccr = _pccr, \
+	.idx = _idx, \
+	.cfg = _cfg, \
+}
+
+#define CONF_SINGLE(lane, proto, pccr, idx, cfg) \
+	CONF(BIT(lane), PROTO_MASK(proto), pccr, idx, cfg)
+
+#define CONF_1000BASEKX(lane, pccr, idx, cfg) \
+	CONF(BIT(lane), PROTO_MASK(SGMII) | PROTO_MASK(1000BASEKX), \
+	     pccr, idx, cfg)
+
+#define CONF_SGMII25(lane, pccr, idx, cfg) \
+	CONF(BIT(lane), PROTO_MASK(SGMII) | PROTO_MASK(SGMII25), \
+	     pccr, idx, cfg)
+
+#define CONF_SGMII25KX(lane, pccr, idx, cfg) \
+	CONF(BIT(lane), \
+	     PROTO_MASK(SGMII) | PROTO_MASK(1000BASEKX) | PROTO_MASK(SGMII25), \
+	     pccr, idx, cfg)
+
+#define CONF_XFI(lane, pccr, idx, cfg) \
+	CONF(BIT(lane), PROTO_MASK(XFI) | PROTO_MASK(10GKR), pccr, idx, cfg)
+
+/**
+ * struct lynx_conf - Configuration for a particular serdes
+ * @modes: Valid protocol controller configurations
+ * @mode_count: Number of modes in @modes
+ * @lanes: Number of lanes
+ * @endian: Endianness of the registers
+ */
+struct lynx_conf {
+	const struct lynx_mode *modes;
+	size_t mode_count;
+	unsigned int lanes;
+	enum regmap_endian endian;
+};
+
+struct lynx_priv;
+
+/**
+ * struct lynx_clk - Driver data for the PLLs
+ * @hw: The clock hardware
+ * @serdes: The parent serdes
+ * @idx: Which PLL this clock is for
+ */
+struct lynx_clk {
+	struct clk_hw hw;
+	struct lynx_priv *serdes;
+	unsigned int idx;
+};
+
+static struct lynx_clk *lynx_clk_hw_to_priv(struct clk_hw *hw)
+{
+	return container_of(hw, struct lynx_clk, hw);
+}
+
+/**
+ * struct lynx_priv - Driver data for the serdes
+ * @lock: A lock protecting "common" registers in @regmap, as well as the
+ *        members of this struct. Lane-specific registers are protected by the
+ *        phy's lock. PLL registers are protected by the clock's lock.
+ * @pll: The PLL clocks
+ * @ref: The reference clocks for the PLLs
+ * @dev: The serdes device
+ * @regmap: The backing regmap
+ * @conf: The configuration for this serdes
+ * @used_lanes: Bitmap of the lanes currently used by phys
+ * @groups: List of the created groups
+ */
+struct lynx_priv {
+	struct mutex lock;
+	struct lynx_clk pll[2];
+	struct clk *ref[2];
+	struct device *dev;
+	struct regmap *regmap;
+	const struct lynx_conf *conf;
+	unsigned int used_lanes;
+	struct list_head groups;
+};
+
+/**
+ * struct lynx_group - Driver data for a group of lanes
+ * @groups: List of other groups; protected by @serdes->lock.
+ * @phy: The associated phy
+ * @serdes: The parent serdes
+ * @pll: The currently-used pll
+ * @first_lane: The first lane in the group
+ * @last_lane: The last lane in the group
+ * @proto: The currently-configured protocol
+ * @users: Number of current users; protected by @serdes->lock.
+ */
+struct lynx_group {
+	struct list_head groups;
+	struct phy *phy;
+	struct lynx_priv *serdes;
+	struct clk *pll;
+	unsigned int first_lane;
+	unsigned int last_lane;
+	enum lynx_protocol proto;
+	unsigned int users;
+};
+
+static u32 lynx_read(struct lynx_priv *serdes, u32 reg)
+{
+	unsigned int ret = 0;
+
+	WARN_ON_ONCE(regmap_read(serdes->regmap, reg, &ret));
+	return ret;
+}
+
+static void lynx_write(struct lynx_priv *serdes, u32 val, u32 reg)
+{
+	WARN_ON_ONCE(regmap_write(serdes->regmap, reg, val));
+}
+
+/* XXX: The output rate is in kHz to avoid overflow on 32-bit arches */
+
+static void lynx_pll_disable(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_clk_hw_to_priv(hw);
+	struct lynx_priv *serdes = clk->serdes;
+	u32 rstctl = lynx_read(serdes, PLLaRSTCTL(clk->idx));
+
+	dev_dbg(clk->serdes->dev, "%s(pll%d)\n", __func__, clk->idx);
+
+	rstctl &= ~PLLaRSTCTL_SDRST_B;
+	lynx_write(serdes, rstctl, PLLaRSTCTL(clk->idx));
+	ndelay(50);
+	rstctl &= ~(PLLaRSTCTL_SDEN | PLLaRSTCTL_PLLRST_B);
+	lynx_write(serdes, rstctl, PLLaRSTCTL(clk->idx));
+	ndelay(100);
+}
+
+static int lynx_pll_enable(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_clk_hw_to_priv(hw);
+	struct lynx_priv *serdes = clk->serdes;
+	u32 rstctl = lynx_read(serdes, PLLaRSTCTL(clk->idx));
+
+	dev_dbg(clk->serdes->dev, "%s(pll%d)\n", __func__, clk->idx);
+
+	rstctl |= PLLaRSTCTL_RSTREQ;
+	lynx_write(serdes, rstctl, PLLaRSTCTL(clk->idx));
+
+	rstctl &= ~PLLaRSTCTL_RSTREQ;
+	rstctl |= PLLaRSTCTL_SDEN | PLLaRSTCTL_PLLRST_B | PLLaRSTCTL_SDRST_B;
+	lynx_write(serdes, rstctl, PLLaRSTCTL(clk->idx));
+
+	/* TODO: wait for the PLL to lock */
+
+	return 0;
+}
+
+static int lynx_pll_is_enabled(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_clk_hw_to_priv(hw);
+	struct lynx_priv *serdes = clk->serdes;
+	u32 rstctl = lynx_read(serdes, PLLaRSTCTL(clk->idx));
+
+	dev_dbg(clk->serdes->dev, "%s(pll%d)\n", __func__, clk->idx);
+
+	return rstctl & PLLaRSTCTL_RST_DONE && !(rstctl & PLLaRSTCTL_RST_ERR);
+}
+
+static const u32 rfclk_sel_map[8] = {
+	[0b000] = 100000000,
+	[0b001] = 125000000,
+	[0b010] = 156250000,
+	[0b011] = 150000000,
+};
+
+/**
+ * lynx_rfclk_to_sel() - Convert a reference clock rate to a selector
+ * @rate: The reference clock rate
+ *
+ * To allow for some variation in the reference clock rate, up to 100ppm of
+ * error is allowed.
+ *
+ * Return: An appropriate selector for @rate, or -%EINVAL.
+ */
+static int lynx_rfclk_to_sel(u32 rate)
+{
+	int ret;
+
+	for (ret = 0; ret < ARRAY_SIZE(rfclk_sel_map); ret++) {
+		u32 rfclk_rate = rfclk_sel_map[ret];
+		/* Allow an error of 100ppm */
+		u32 error = rfclk_rate / 10000;
+
+		if (rate > rfclk_rate - error && rate < rfclk_rate + error)
+			return ret;
+	}
+
+	return -EINVAL;
+}
+
+static const u32 frate_sel_map[16] = {
+	[0b0000] = 5000000,
+	[0b0101] = 3750000,
+	[0b0110] = 5156250,
+	[0b0111] = 4000000,
+	[0b1001] = 3125000,
+	[0b1010] = 3000000,
+};
+
+/**
+ * lynx_frate_to_sel() - Convert a VCO clock rate to a selector
+ * @rate_khz: The VCO frequency, in kHz
+ *
+ * Return: An appropriate selector for @rate_khz, or -%EINVAL.
+ */
+static int lynx_frate_to_sel(u32 rate_khz)
+{
+	int ret;
+
+	for (ret = 0; ret < ARRAY_SIZE(frate_sel_map); ret++)
+		if (frate_sel_map[ret] == rate_khz)
+			return ret;
+
+	return -EINVAL;
+}
+
+static u32 lynx_pll_ratio(u32 frate_sel, u32 rfclk_sel)
+{
+	u64 frate;
+	u32 rfclk, error, ratio;
+
+	frate = frate_sel_map[frate_sel] * (u64)HZ_PER_KHZ;
+	rfclk = rfclk_sel_map[rfclk_sel];
+
+	if (!frate || !rfclk)
+		return 0;
+
+	ratio = div_u64_rem(frate, rfclk, &error);
+	if (!error)
+		return ratio;
+	return 0;
+}
+
+static unsigned long lynx_pll_recalc_rate(struct clk_hw *hw,
+					unsigned long parent_rate)
+{
+	struct lynx_clk *clk = lynx_clk_hw_to_priv(hw);
+	struct lynx_priv *serdes = clk->serdes;
+	u32 cr0 = lynx_read(serdes, PLLaCR0(clk->idx));
+	u32 frate_sel = FIELD_GET(PLLaCR0_FRATE_SEL, cr0);
+	u32 rfclk_sel = FIELD_GET(PLLaCR0_RFCLK_SEL, cr0);
+	unsigned long ret;
+
+	dev_dbg(clk->serdes->dev, "%s(pll%d, %lu)\n", __func__,
+		clk->idx, parent_rate);
+
+	ret = mult_frac(parent_rate, lynx_pll_ratio(frate_sel, rfclk_sel),
+			 HZ_PER_KHZ);
+	return ret;
+}
+
+static long lynx_pll_round_rate(struct clk_hw *hw, unsigned long rate_khz,
+			      unsigned long *parent_rate)
+{
+	int frate_sel, rfclk_sel;
+	struct lynx_clk *clk = lynx_clk_hw_to_priv(hw);
+	u32 ratio;
+
+	dev_dbg(clk->serdes->dev, "%s(pll%d, %lu, %lu)\n", __func__,
+		clk->idx, rate_khz, *parent_rate);
+
+	frate_sel = lynx_frate_to_sel(rate_khz);
+	if (frate_sel < 0)
+		return frate_sel;
+
+	rfclk_sel = lynx_rfclk_to_sel(*parent_rate);
+	if (rfclk_sel >= 0) {
+		ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+		if (ratio)
+			return mult_frac(*parent_rate, ratio, HZ_PER_KHZ);
+	}
+
+	for (rfclk_sel = 0;
+	     rfclk_sel < ARRAY_SIZE(rfclk_sel_map);
+	     rfclk_sel++) {
+		ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+		if (ratio) {
+			*parent_rate = rfclk_sel_map[rfclk_sel];
+			return mult_frac(*parent_rate, ratio, HZ_PER_KHZ);
+		}
+	}
+
+	return -EINVAL;
+}
+
+static int lynx_pll_set_rate(struct clk_hw *hw, unsigned long rate_khz,
+			   unsigned long parent_rate)
+{
+	int frate_sel, rfclk_sel, ret;
+	struct lynx_clk *clk = lynx_clk_hw_to_priv(hw);
+	struct lynx_priv *serdes = clk->serdes;
+	u32 ratio, cr0 = lynx_read(serdes, PLLaCR0(clk->idx));
+
+	dev_dbg(clk->serdes->dev, "%s(pll%d, %lu, %lu)\n", __func__,
+		clk->idx, rate_khz, parent_rate);
+
+	frate_sel = lynx_frate_to_sel(rate_khz);
+	if (frate_sel < 0)
+		return frate_sel;
+
+	/* First try the existing rate */
+	rfclk_sel = lynx_rfclk_to_sel(parent_rate);
+	if (rfclk_sel >= 0) {
+		ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+		if (ratio)
+			goto got_rfclk;
+	}
+
+	for (rfclk_sel = 0;
+	     rfclk_sel < ARRAY_SIZE(rfclk_sel_map);
+	     rfclk_sel++) {
+		ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+		if (ratio) {
+			ret = clk_set_rate(serdes->ref[clk->idx],
+					   rfclk_sel_map[rfclk_sel]);
+			if (!ret)
+				goto got_rfclk;
+		}
+	}
+
+	return ret;
+
+got_rfclk:
+	cr0 &= ~(PLLaCR0_RFCLK_SEL | PLLaCR0_FRATE_SEL);
+	cr0 |= FIELD_PREP(PLLaCR0_RFCLK_SEL, rfclk_sel);
+	cr0 |= FIELD_PREP(PLLaCR0_FRATE_SEL, frate_sel);
+	lynx_write(serdes, cr0, PLLaCR0(clk->idx));
+	return 0;
+}
+
+static const struct clk_ops lynx_pll_clk_ops = {
+	.enable = lynx_pll_enable,
+	.disable = lynx_pll_disable,
+	.is_enabled = lynx_pll_is_enabled,
+	.recalc_rate = lynx_pll_recalc_rate,
+	.round_rate = lynx_pll_round_rate,
+	.set_rate = lynx_pll_set_rate,
+};
+
+static struct clk_hw *lynx_clk_get(struct of_phandle_args *clkspec, void *data)
+{
+	struct lynx_priv *serdes = data;
+
+	if (clkspec->args_count != 1)
+		return ERR_PTR(-EINVAL);
+
+	if (clkspec->args[0] > 1)
+		return ERR_PTR(-EINVAL);
+
+	return &serdes->pll[clkspec->args[0]].hw;
+}
+
+/**
+ * lynx_lane_bitmap() - Get a bitmap for a group of lanes
+ * @group: The group of lanes
+ *
+ * Return: A mask containing all bits between @group->first and @group->last
+ */
+static unsigned int lynx_lane_bitmap(struct lynx_group *group)
+{
+	if (group->first_lane > group->last_lane)
+		return GENMASK(group->first_lane, group->last_lane);
+	else
+		return GENMASK(group->last_lane, group->first_lane);
+}
+
+static int lynx_init(struct phy *phy)
+{
+	int ret = 0;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+	unsigned int lane_mask = lynx_lane_bitmap(group);
+
+	mutex_lock(&serdes->lock);
+	if (serdes->used_lanes & lane_mask)
+		ret = -EBUSY;
+	else
+		serdes->used_lanes |= lane_mask;
+	mutex_unlock(&serdes->lock);
+	return ret;
+}
+
+static int lynx_exit(struct phy *phy)
+{
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+
+	clk_disable_unprepare(group->pll);
+	clk_rate_exclusive_put(group->pll);
+	group->pll = NULL;
+
+	mutex_lock(&serdes->lock);
+	serdes->used_lanes &= ~lynx_lane_bitmap(group);
+	mutex_unlock(&serdes->lock);
+	return 0;
+}
+
+/*
+ * This is tricky. If first_lane=1 and last_lane=0, the condition will see 2,
+ * 1, 0. But the loop body will see 1, 0. We do this to avoid underflow. We
+ * can't pull the same trick when incrementing, because then we might have to
+ * start at -1 if (e.g.) first_lane = 0.
+ */
+#define for_range(val, start, end) \
+	for (val = start < end ? start : start + 1; \
+	     start < end ? val <= end : val-- > end; \
+	     start < end ? val++ : 0)
+#define for_each_lane(lane, group) \
+	for_range(lane, group->first_lane, group->last_lane)
+#define for_each_lane_reverse(lane, group) \
+	for_range(lane, group->last_lane, group->first_lane)
+
+static int lynx_power_on(struct phy *phy)
+{
+	int i;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	u32 gcr0;
+
+	for_each_lane(i, group) {
+		gcr0 = lynx_read(group->serdes, LNmGCR0(i));
+		gcr0 &= ~(LNmGCR0_RX_PD | LNmGCR0_TX_PD);
+		lynx_write(group->serdes, gcr0, LNmGCR0(i));
+
+		usleep_range(15, 30);
+		gcr0 |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
+		lynx_write(group->serdes, gcr0, LNmGCR0(i));
+	}
+
+	return 0;
+}
+
+static void lynx_power_off_lane(struct lynx_priv *serdes, unsigned int lane)
+{
+	u32 gcr0 = lynx_read(serdes, LNmGCR0(lane));
+
+	gcr0 |= LNmGCR0_RX_PD | LNmGCR0_TX_PD;
+	gcr0 &= ~(LNmGCR0_RRST_B | LNmGCR0_TRST_B);
+	lynx_write(serdes, gcr0, LNmGCR0(lane));
+}
+
+static int lynx_power_off(struct phy *phy)
+{
+	unsigned int i;
+	struct lynx_group *group = phy_get_drvdata(phy);
+
+	for_each_lane_reverse(i, group)
+		lynx_power_off_lane(group->serdes, i);
+
+	return 0;
+}
+
+/**
+ * lynx_lookup_proto() - Convert a phy-subsystem mode to a protocol
+ * @mode: The mode to convert
+ * @submode: The submode of @mode
+ *
+ * Return: A corresponding serdes-specific mode
+ */
+static enum lynx_protocol lynx_lookup_proto(enum phy_mode mode, int submode)
+{
+	switch (mode) {
+	case PHY_MODE_ETHERNET:
+		switch (submode) {
+		case PHY_INTERFACE_MODE_SGMII:
+		case PHY_INTERFACE_MODE_1000BASEX:
+			return LYNX_PROTO_SGMII;
+		case PHY_INTERFACE_MODE_2500BASEX:
+			return LYNX_PROTO_SGMII25;
+		case PHY_INTERFACE_MODE_QSGMII:
+			return LYNX_PROTO_QSGMII;
+		case PHY_INTERFACE_MODE_XGMII:
+		case PHY_INTERFACE_MODE_10GBASER:
+			return LYNX_PROTO_XFI;
+		case PHY_INTERFACE_MODE_10GKR:
+			return LYNX_PROTO_10GKR;
+		default:
+			return LYNX_PROTO_NONE;
+		}
+	/* Not implemented (yet) */
+	case PHY_MODE_PCIE:
+	case PHY_MODE_SATA:
+	default:
+		return LYNX_PROTO_NONE;
+	}
+}
+
+/**
+ * lynx_lookup_mode() - Get the mode for a group/protocol combination
+ * @group: The group of lanes to use
+ * @proto: The protocol to use
+ *
+ * Return: An appropriate mode to use, or %NULL if none match.
+ */
+static const struct lynx_mode *lynx_lookup_mode(struct lynx_group *group,
+					    enum lynx_protocol proto)
+{
+	int i;
+	const struct lynx_conf *conf = group->serdes->conf;
+
+	for (i = 0; i < conf->mode_count; i++) {
+		const struct lynx_mode *mode = &conf->modes[i];
+
+		if (BIT(proto) & mode->protos &&
+		    lynx_lane_bitmap(group) == mode->lanes)
+			return mode;
+	}
+
+	return NULL;
+}
+
+static int lynx_validate(struct phy *phy, enum phy_mode phy_mode, int submode,
+		       union phy_configure_opts *opts)
+{
+	enum lynx_protocol proto;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	const struct lynx_mode *mode;
+
+	proto = lynx_lookup_proto(phy_mode, submode);
+	if (proto == LYNX_PROTO_NONE)
+		return -EINVAL;
+
+	/* Nothing to do */
+	if (proto == group->proto)
+		return 0;
+
+	mode = lynx_lookup_mode(group, proto);
+	if (!mode)
+		return -EINVAL;
+
+	return 0;
+}
+
+/**
+ * lynx_proto_mode_mask() - Get the mask for a PCCR config
+ * @mode: The mode to use
+ *
+ * Return: The mask, shifted down to the lsb.
+ */
+static u32 lynx_proto_mode_mask(const struct lynx_mode *mode)
+{
+	switch (mode->pccr) {
+	case 0x0:
+		if (mode->protos & PROTO_MASK(PCIE))
+			return PCCR0_PEXa_MASK;
+		break;
+	case 0x2:
+		if (mode->protos & PROTO_MASK(SATA))
+			return PCCR2_SATAa_MASK;
+		break;
+	case 0x8:
+		if (mode->protos & PROTO_MASK(SGMII))
+			return PCCR8_SGMIIa_MASK;
+		break;
+	case 0x9:
+		if (mode->protos & PROTO_MASK(QSGMII))
+			return PCCR9_QSGMIIa_MASK;
+		break;
+	case 0xB:
+		if (mode->protos & PROTO_MASK(XFI))
+			return PCCRB_XFIa_MASK;
+		break;
+	}
+	pr_err("unknown mode PCCR%X %s%c\n", mode->pccr,
+	       lynx_proto_str[mode->protos], 'A' + mode->idx);
+	return 0;
+}
+
+/**
+ * lynx_proto_mode_shift() - Get the shift for a PCCR config
+ * @mode: The mode to use
+ *
+ * Return: The amount of bits to shift the mask.
+ */
+static u32 lynx_proto_mode_shift(const struct lynx_mode *mode)
+{
+	switch (mode->pccr) {
+	case 0x0:
+		if (mode->protos & PROTO_MASK(PCIE))
+			return PCCR0_PEXa_SHIFT(mode->idx);
+		break;
+	case 0x2:
+		if (mode->protos & PROTO_MASK(SATA))
+			return PCCR2_SATAa_SHIFT(mode->idx);
+		break;
+	case 0x8:
+		if (mode->protos & PROTO_MASK(SGMII))
+			return PCCR8_SGMIIa_SHIFT(mode->idx);
+		break;
+	case 0x9:
+		if (mode->protos & PROTO_MASK(QSGMII))
+			return PCCR9_QSGMIIa_SHIFT(mode->idx);
+		break;
+	case 0xB:
+		if (mode->protos & PROTO_MASK(XFI))
+			return PCCRB_XFIa_SHIFT(mode->idx);
+		break;
+	}
+	pr_err("unknown mode PCCR%X %s%c\n", mode->pccr,
+	       lynx_proto_str[mode->protos], 'A' + mode->idx);
+	return 0;
+}
+
+/**
+ * lynx_proto_mode_get() - Get the current config for a PCCR mode
+ * @mode: The mode to use
+ * @pccr: The current value of the PCCR
+ *
+ * Return: The current value of the PCCR config for this mode
+ */
+static u32 lynx_proto_mode_get(const struct lynx_mode *mode, u32 pccr)
+{
+	return (pccr >> lynx_proto_mode_shift(mode)) &
+	       lynx_proto_mode_mask(mode);
+}
+
+/**
+ * lynx_proto_mode_prep() - Configure a PCCR for a protocol
+ * @mode: The mode to use
+ * @pccr: The current value of the PCCR
+ * @proto: The protocol to configure
+ *
+ * This configures a PCCR for a mode and protocol. To disable a mode, pass
+ * %LYNX_PROTO_NONE as @proto. If @proto is 1000Base-KX, then the KX bit
+ * will be set.
+ *
+ * Return: The new value for the PCCR
+ */
+static u32 lynx_proto_mode_prep(const struct lynx_mode *mode, u32 pccr,
+				enum lynx_protocol proto)
+{
+	u32 shift = lynx_proto_mode_shift(mode);
+
+	pccr &= ~(lynx_proto_mode_mask(mode) << shift);
+	if (proto != LYNX_PROTO_NONE)
+		pccr |= mode->cfg << shift;
+
+	if (proto == LYNX_PROTO_1000BASEKX) {
+		if (mode->pccr == 8)
+			pccr |= PCCR8_SGMIIa_KX << shift;
+		else
+			pr_err("PCCR%X doesn't have a KX bit\n", mode->pccr);
+	}
+
+	return pccr;
+}
+
+#define abs_diff(a, b) ({ \
+	typeof(a) _a = (a); \
+	typeof(b) _b = (b); \
+	_a > _b ? _a - _b : _b - _a; \
+})
+
+static int lynx_set_mode(struct phy *phy, enum phy_mode phy_mode, int submode)
+{
+	enum lynx_protocol proto;
+	const struct lynx_proto_params *params;
+	const struct lynx_mode *old_mode = NULL, *new_mode;
+	int i, pll, ret;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+	u32 tmp;
+	u32 gcr0 = 0, gcr1 = 0, recr0 = 0, tecr0 = 0;
+	u32 gcr0_mask = 0, gcr1_mask = 0, recr0_mask = 0, tecr0_mask = 0;
+
+	proto = lynx_lookup_proto(phy_mode, submode);
+	if (proto == LYNX_PROTO_NONE) {
+		dev_dbg(&phy->dev, "unknown mode/submode %d/%d\n",
+			phy_mode, submode);
+		return -EINVAL;
+	}
+
+	/* Nothing to do */
+	if (proto == group->proto)
+		return 0;
+
+	new_mode = lynx_lookup_mode(group, proto);
+	if (!new_mode) {
+		dev_dbg(&phy->dev, "could not find mode for %s on lanes %u to %u\n",
+			lynx_proto_str[proto], group->first_lane,
+			group->last_lane);
+		return -EINVAL;
+	}
+
+	if (group->proto != LYNX_PROTO_NONE) {
+		old_mode = lynx_lookup_mode(group, group->proto);
+		if (!old_mode) {
+			dev_err(&phy->dev, "could not find mode for %s\n",
+				lynx_proto_str[group->proto]);
+			return -EBUSY;
+		}
+	}
+
+	clk_disable_unprepare(group->pll);
+	clk_rate_exclusive_put(group->pll);
+	group->pll = NULL;
+
+	/* First, try to use a PLL which already has the correct rate */
+	params = &lynx_proto_params[proto];
+	for (pll = 0; pll < ARRAY_SIZE(serdes->pll); pll++) {
+		struct clk *clk = serdes->pll[pll].hw.clk;
+		unsigned long rate = clk_get_rate(clk);
+		unsigned long error = abs_diff(rate, params->frate_khz);
+
+		dev_dbg(&phy->dev, "pll%d has rate %lu\n", pll, rate);
+		/* Accept up to 100ppm deviation */
+		if ((!error || params->frate_khz / error > 10000) &&
+		    !clk_set_rate_exclusive(clk, rate))
+			goto got_pll;
+		/* Someone else got a different rate first */
+	}
+
+	/* If neither PLL has the right rate, try setting it */
+	for (pll = 0; pll < 2; pll++) {
+		ret = clk_set_rate_exclusive(serdes->pll[pll].hw.clk,
+					     params->frate_khz);
+		if (!ret)
+			goto got_pll;
+	}
+
+	dev_dbg(&phy->dev, "could not get a pll at %ukHz\n",
+		params->frate_khz);
+	return ret;
+
+got_pll:
+	group->pll = serdes->pll[pll].hw.clk;
+	clk_prepare_enable(group->pll);
+
+	gcr0_mask |= LNmGCR0_RRAT_SEL | LNmGCR0_TRAT_SEL;
+	gcr0_mask |= LNmGCR0_RPLL_LES | LNmGCR0_TPLL_LES;
+	gcr0_mask |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
+	gcr0_mask |= LNmGCR0_RX_PD | LNmGCR0_TX_PD;
+	gcr0_mask |= LNmGCR0_IF20BIT_EN | LNmGCR0_PROTS;
+	gcr0 |= FIELD_PREP(LNmGCR0_RPLL_LES, !pll);
+	gcr0 |= FIELD_PREP(LNmGCR0_TPLL_LES, !pll);
+	gcr0 |= FIELD_PREP(LNmGCR0_RRAT_SEL, params->rat_sel);
+	gcr0 |= FIELD_PREP(LNmGCR0_TRAT_SEL, params->rat_sel);
+	gcr0 |= FIELD_PREP(LNmGCR0_IF20BIT_EN, params->if20bit);
+	gcr0 |= FIELD_PREP(LNmGCR0_PROTS, params->prots);
+
+	gcr1_mask |= LNmGCR1_RDAT_INV | LNmGCR1_TDAT_INV;
+	gcr1_mask |= LNmGCR1_OPAD_CTL | LNmGCR1_REIDL_TH;
+	gcr1_mask |= LNmGCR1_REIDL_EX_SEL | LNmGCR1_REIDL_ET_SEL;
+	gcr1_mask |= LNmGCR1_REIDL_EX_MSB | LNmGCR1_REIDL_ET_MSB;
+	gcr1_mask |= LNmGCR1_REQ_CTL_SNP | LNmGCR1_REQ_CDR_SNP;
+	gcr1_mask |= LNmGCR1_TRSTDIR | LNmGCR1_REQ_BIN_SNP;
+	gcr1_mask |= LNmGCR1_ISLEW_RCTL | LNmGCR1_OSLEW_RCTL;
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_TH, params->reidl_th);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_EX_SEL, params->reidl_ex & 3);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_ET_SEL, params->reidl_et & 3);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_EX_MSB, params->reidl_ex >> 2);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_ET_MSB, params->reidl_et >> 2);
+	gcr1 |= FIELD_PREP(LNmGCR1_TRSTDIR,
+			   group->first_lane > group->last_lane);
+	gcr1 |= FIELD_PREP(LNmGCR1_ISLEW_RCTL, params->slew);
+	gcr1 |= FIELD_PREP(LNmGCR1_OSLEW_RCTL, params->slew);
+
+	recr0_mask |= LNmRECR0_GK2OVD | LNmRECR0_GK3OVD;
+	recr0_mask |= LNmRECR0_GK2OVD_EN | LNmRECR0_GK3OVD_EN;
+	recr0_mask |= LNmRECR0_BASE_WAND | LNmRECR0_OSETOVD;
+	if (params->gain) {
+		recr0 |= FIELD_PREP(LNmRECR0_GK2OVD, params->gain);
+		recr0 |= FIELD_PREP(LNmRECR0_GK3OVD, params->gain);
+		recr0 |= LNmRECR0_GK2OVD_EN | LNmRECR0_GK3OVD_EN;
+	}
+	recr0 |= FIELD_PREP(LNmRECR0_BASE_WAND, params->baseline_wander);
+	recr0 |= FIELD_PREP(LNmRECR0_OSETOVD, params->offset_override);
+
+	tecr0_mask |= LNmTECR0_TEQ_TYPE;
+	tecr0_mask |= LNmTECR0_SGN_PREQ | LNmTECR0_RATIO_PREQ;
+	tecr0_mask |= LNmTECR0_SGN_POST1Q | LNmTECR0_RATIO_PST1Q;
+	tecr0_mask |= LNmTECR0_ADPT_EQ | LNmTECR0_AMP_RED;
+	tecr0 |= FIELD_PREP(LNmTECR0_TEQ_TYPE, params->teq);
+	if (params->preq_ratio) {
+		tecr0 |= FIELD_PREP(LNmTECR0_SGN_PREQ, 1);
+		tecr0 |= FIELD_PREP(LNmTECR0_RATIO_PREQ, params->preq_ratio);
+	}
+	if (params->postq_ratio) {
+		tecr0 |= FIELD_PREP(LNmTECR0_SGN_POST1Q, 1);
+		tecr0 |= FIELD_PREP(LNmTECR0_RATIO_PST1Q, params->postq_ratio);
+	}
+	tecr0 |= FIELD_PREP(LNmTECR0_ADPT_EQ, params->adpt_eq);
+	tecr0 |= FIELD_PREP(LNmTECR0_AMP_RED, params->amp_red);
+
+	mutex_lock(&serdes->lock);
+
+	/* Disable the old controller */
+	if (old_mode) {
+		tmp = lynx_read(serdes, PCCRn(old_mode->pccr));
+		tmp = lynx_proto_mode_prep(old_mode, tmp, LYNX_PROTO_NONE);
+		lynx_write(serdes, tmp, PCCRn(old_mode->pccr));
+
+		if (old_mode->protos & PROTO_MASK(SGMII)) {
+			tmp = lynx_read(serdes, SGMIIaCR1(old_mode->idx));
+			tmp &= SGMIIaCR1_SGPCS_EN;
+			lynx_write(serdes, tmp, SGMIIaCR1(old_mode->idx));
+		}
+	}
+
+	for_each_lane_reverse(i, group) {
+		tmp = lynx_read(serdes, LNmGCR0(i));
+		tmp &= ~(LNmGCR0_RRST_B | LNmGCR0_TRST_B);
+		lynx_write(serdes, tmp, LNmGCR0(i));
+		ndelay(50);
+
+		tmp &= ~gcr0_mask;
+		tmp |= gcr0;
+		tmp |= FIELD_PREP(LNmGCR0_FIRST_LANE, i == group->first_lane);
+		lynx_write(serdes, tmp, LNmGCR0(i));
+
+		tmp = lynx_read(serdes, LNmGCR1(i));
+		tmp &= ~gcr1_mask;
+		tmp |= gcr1;
+		lynx_write(serdes, tmp, LNmGCR1(i));
+
+		tmp = lynx_read(serdes, LNmRECR0(i));
+		tmp &= ~recr0_mask;
+		tmp |= recr0;
+		lynx_write(serdes, tmp, LNmRECR0(i));
+
+		tmp = lynx_read(serdes, LNmTECR0(i));
+		tmp &= ~tecr0_mask;
+		tmp |= tecr0;
+		lynx_write(serdes, tmp, LNmTECR0(i));
+
+		tmp = lynx_read(serdes, LNmTTLCR0(i));
+		tmp &= ~LNmTTLCR0_FLT_SEL;
+		tmp |= FIELD_PREP(LNmTTLCR0_FLT_SEL, params->flt_sel);
+		lynx_write(serdes, tmp, LNmTTLCR0(i));
+
+		ndelay(120);
+		tmp = lynx_read(serdes, LNmGCR0(i));
+		tmp |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
+		lynx_write(serdes, tmp, LNmGCR0(i));
+	}
+
+	if (proto == LYNX_PROTO_1000BASEKX) {
+		/* FIXME: this races with clock updates */
+		tmp = lynx_read(serdes, PLLaCR0(pll));
+		tmp &= ~PLLaCR0_DLYDIV_SEL;
+		tmp |= FIELD_PREP(PLLaCR0_DLYDIV_SEL, 1);
+		lynx_write(serdes, tmp, PLLaCR0(pll));
+	}
+
+	/* Enable the new controller */
+	tmp = lynx_read(serdes, PCCRn(new_mode->pccr));
+	tmp = lynx_proto_mode_prep(new_mode, tmp, proto);
+	lynx_write(serdes, tmp, PCCRn(new_mode->pccr));
+
+	if (new_mode->protos & PROTO_MASK(SGMII)) {
+		tmp = lynx_read(serdes, SGMIIaCR1(new_mode->idx));
+		tmp |= SGMIIaCR1_SGPCS_EN;
+		lynx_write(serdes, tmp, SGMIIaCR1(new_mode->idx));
+	}
+
+	mutex_unlock(&serdes->lock);
+
+	group->proto = proto;
+	dev_dbg(&phy->dev, "set mode to %s on lanes %u to %u\n",
+		lynx_proto_str[proto], group->first_lane, group->last_lane);
+	return 0;
+}
+
+static void lynx_release(struct phy *phy)
+{
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+
+	mutex_lock(&serdes->lock);
+	if (--group->users) {
+		mutex_unlock(&serdes->lock);
+		return;
+	}
+	list_del(&group->groups);
+	mutex_unlock(&serdes->lock);
+
+	phy_destroy(phy);
+	kfree(group);
+}
+
+static const struct phy_ops lynx_phy_ops = {
+	.init = lynx_init,
+	.exit = lynx_exit,
+	.power_on = lynx_power_on,
+	.power_off = lynx_power_off,
+	.set_mode = lynx_set_mode,
+	.validate = lynx_validate,
+	.release = lynx_release,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *lynx_xlate(struct device *dev, struct of_phandle_args *args)
+{
+	struct phy *phy;
+	struct list_head *head;
+	struct lynx_group *group;
+	struct lynx_priv *serdes = dev_get_drvdata(dev);
+	unsigned int last_lane;
+
+	if (args->args_count == 1)
+		last_lane = args->args[0];
+	else if (args->args_count == 2)
+		last_lane = args->args[1];
+	else
+		return ERR_PTR(-EINVAL);
+
+	mutex_lock(&serdes->lock);
+
+	/* Look for an existing group */
+	list_for_each(head, &serdes->groups) {
+		group = container_of(head, struct lynx_group, groups);
+		if (group->first_lane == args->args[0] &&
+		    group->last_lane == last_lane) {
+			group->users++;
+			return group->phy;
+		}
+	}
+
+	/* None found, create our own */
+	group = kzalloc(sizeof(*group), GFP_KERNEL);
+	if (!group) {
+		mutex_unlock(&serdes->lock);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	group->serdes = serdes;
+	group->first_lane = args->args[0];
+	group->last_lane = last_lane;
+	group->users = 1;
+	phy = phy_create(dev, NULL, &lynx_phy_ops);
+	if (IS_ERR(phy)) {
+		kfree(group);
+	} else {
+		group->phy = phy;
+		phy_set_drvdata(phy, group);
+		list_add(&group->groups, &serdes->groups);
+	}
+
+	mutex_unlock(&serdes->lock);
+	return phy;
+}
+
+static int lynx_probe(struct platform_device *pdev)
+{
+	bool grabbed_clocks = false;
+	int i, ret;
+	struct device *dev = &pdev->dev;
+	struct lynx_priv *serdes;
+	struct regmap_config regmap_config = {};
+	const struct lynx_conf *conf;
+	struct resource *res;
+	void __iomem *base;
+
+	serdes = devm_kzalloc(dev, sizeof(*serdes), GFP_KERNEL);
+	if (!serdes)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, serdes);
+	mutex_init(&serdes->lock);
+	INIT_LIST_HEAD(&serdes->groups);
+	serdes->dev = dev;
+
+	base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(base)) {
+		ret = PTR_ERR(base);
+		dev_err_probe(dev, ret, "could not get/map registers\n");
+		return ret;
+	}
+
+	conf = device_get_match_data(dev);
+	serdes->conf = conf;
+	regmap_config.reg_bits = 32;
+	regmap_config.reg_stride = 4;
+	regmap_config.val_bits = 32;
+	regmap_config.val_format_endian = conf->endian;
+	regmap_config.max_register = res->end - res->start;
+	regmap_config.disable_locking = true;
+	serdes->regmap = devm_regmap_init_mmio(dev, base, &regmap_config);
+	if (IS_ERR(serdes->regmap)) {
+		ret = PTR_ERR(serdes->regmap);
+		dev_err_probe(dev, ret, "could not create regmap\n");
+		return ret;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(serdes->ref); i++) {
+		static const char fmt[] = "ref%d";
+		char name[sizeof(fmt)];
+
+		snprintf(name, sizeof(name), fmt, i);
+		serdes->ref[i] = devm_clk_get(dev, name);
+		if (IS_ERR(serdes->ref[i])) {
+			ret = PTR_ERR(serdes->ref[i]);
+			dev_err_probe(dev, ret, "could not get %s\n", name);
+			return ret;
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(serdes->pll); i++) {
+		static const char fmt[] = "%s.pll%d";
+		char *name;
+		const struct clk_hw *ref_hw[] = {
+			__clk_get_hw(serdes->ref[i]),
+		};
+		size_t len;
+		struct clk_init_data init = {};
+
+		len = snprintf(NULL, 0, fmt, pdev->name, i);
+		name = devm_kzalloc(dev, len + 1, GFP_KERNEL);
+		if (!name)
+			return -ENOMEM;
+
+		snprintf(name, len + 1, fmt, pdev->name, i);
+		init.name = name;
+		init.ops = &lynx_pll_clk_ops;
+		init.parent_hws = ref_hw;
+		init.num_parents = 1;
+		init.flags = CLK_SET_RATE_GATE | CLK_GET_RATE_NOCACHE;
+		init.flags |= CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE;
+
+		serdes->pll[i].hw.init = &init;
+		serdes->pll[i].serdes = serdes;
+		serdes->pll[i].idx = i;
+		ret = devm_clk_hw_register(dev, &serdes->pll[i].hw);
+		if (ret) {
+			dev_err_probe(dev, ret, "could not register %s\n",
+				      name);
+			return ret;
+		}
+	}
+
+	ret = devm_of_clk_add_hw_provider(dev, lynx_clk_get, serdes);
+	if (ret) {
+		dev_err_probe(dev, ret, "could not register clock provider\n");
+		return ret;
+	}
+
+	/* Deselect anything configured by the RCW/bootloader */
+	for (i = 0; i < conf->mode_count; i++) {
+		const struct lynx_mode *mode = &conf->modes[i];
+		u32 pccr = lynx_read(serdes, PCCRn(mode->pccr));
+
+		if (lynx_proto_mode_get(mode, pccr) == mode->cfg) {
+			if (mode->protos & UNSUPPORTED_PROTOS) {
+				/* Don't mess with modes we don't support */
+				serdes->used_lanes |= mode->lanes;
+				if (grabbed_clocks)
+					continue;
+
+				grabbed_clocks = true;
+				clk_prepare_enable(serdes->pll[0].hw.clk);
+				clk_prepare_enable(serdes->pll[1].hw.clk);
+				clk_rate_exclusive_get(serdes->pll[0].hw.clk);
+				clk_rate_exclusive_get(serdes->pll[1].hw.clk);
+			} else {
+				/* Otherwise, clear out the existing config */
+				pccr = lynx_proto_mode_prep(mode, pccr,
+							    LYNX_PROTO_NONE);
+				lynx_write(serdes, pccr, PCCRn(mode->pccr));
+			}
+
+			/* Disable the SGMII PCS until we're ready for it */
+			if (mode->protos & LYNX_PROTO_SGMII) {
+				u32 cr1;
+
+				cr1 = lynx_read(serdes, SGMIIaCR1(mode->idx));
+				cr1 &= ~SGMIIaCR1_SGPCS_EN;
+				lynx_write(serdes, cr1, SGMIIaCR1(mode->idx));
+			}
+		}
+	}
+
+	/* Power off all lanes; used ones will be powered on later */
+	for (i = 0; i < conf->lanes; i++)
+		lynx_power_off_lane(serdes, i);
+
+	ret = PTR_ERR_OR_ZERO(devm_of_phy_provider_register(dev, lynx_xlate));
+	if (ret)
+		dev_err_probe(dev, ret, "could not register phy provider\n");
+	else
+		dev_info(dev, "probed with %d lanes\n", conf->lanes);
+	return ret;
+}
+
+/*
+ * XXX: For SerDes1, lane A uses pins SD1_RX3_P/N! That is, the lane numbers
+ * and pin numbers are _reversed_. In addition, the PCCR documentation is
+ * _inconsistent_ in its usage of these terms!
+ *
+ * PCCR "Lane 0" refers to...
+ * ==== =====================
+ *    0 Lane A
+ *    2 Lane A
+ *    8 Lane A
+ *    9 Lane A
+ *    B Lane D!
+ */
+static const struct lynx_mode ls1046a_modes1[] = {
+	CONF_SINGLE(1, PCIE, 0x0, 1, 0b001), /* PCIe.1 x1 */
+	CONF_1000BASEKX(0, 0x8, 0, 0b001), /* SGMII.6 */
+	CONF_SGMII25KX(1, 0x8, 1, 0b001), /* SGMII.5 */
+	CONF_SGMII25KX(2, 0x8, 2, 0b001), /* SGMII.10 */
+	CONF_SGMII25KX(3, 0x8, 3, 0b001), /* SGMII.9 */
+	CONF_SINGLE(1, QSGMII, 0x9, 2, 0b001), /* QSGMII.6,5,10,1 */
+	CONF_XFI(2, 0xB, 0, 0b010), /* XFI.10 */
+	CONF_XFI(3, 0xB, 1, 0b001), /* XFI.9 */
+};
+
+static const struct lynx_conf ls1046a_conf1 = {
+	.modes = ls1046a_modes1,
+	.mode_count = ARRAY_SIZE(ls1046a_modes1),
+	.lanes = 4,
+	.endian = REGMAP_ENDIAN_BIG,
+};
+
+static const struct lynx_mode ls1046a_modes2[] = {
+	CONF_SINGLE(0, PCIE, 0x0, 0, 0b001), /* PCIe.1 x1 */
+	CONF(GENMASK(3, 0), PROTO_MASK(PCIE), 0x0, 0, 0b011), /* PCIe.1 x4 */
+	CONF_SINGLE(2, PCIE, 0x0, 2, 0b001), /* PCIe.2 x1 */
+	CONF(GENMASK(3, 2), PROTO_MASK(PCIE), 0x0, 2, 0b010), /* PCIe.3 x2 */
+	CONF_SINGLE(3, PCIE, 0x0, 2, 0b011), /* PCIe.3 x1 */
+	CONF_SINGLE(3, SATA, 0x2, 0, 0b001), /* SATA */
+	CONF_1000BASEKX(1, 0x8, 1, 0b001), /* SGMII.2 */
+};
+
+static const struct lynx_conf ls1046a_conf2 = {
+	.modes = ls1046a_modes2,
+	.mode_count = ARRAY_SIZE(ls1046a_modes2),
+	.lanes = 4,
+	.endian = REGMAP_ENDIAN_BIG,
+};
+
+static const struct of_device_id lynx_of_match[] = {
+	{ .compatible = "fsl,ls1046a-serdes-1", .data = &ls1046a_conf1 },
+	{ .compatible = "fsl,ls1046a-serdes-2", .data = &ls1046a_conf2 },
+};
+MODULE_DEVICE_TABLE(of, lynx_of_match);
+
+static struct platform_driver lynx_driver = {
+	.probe = lynx_probe,
+	.driver = {
+		.name = "qoriq_serdes",
+		.of_match_table = lynx_of_match,
+	},
+};
+module_platform_driver(lynx_driver);
+
+MODULE_AUTHOR("Sean Anderson <sean.anderson@seco.com>");
+MODULE_DESCRIPTION("Lynx 10G SerDes driver");
+MODULE_LICENSE("GPL");