diff mbox series

[v3,2/3] phy: qcom-snps: Add support for overriding phy tuning parameters

Message ID 1652011947-18575-3-git-send-email-quic_kriskura@quicinc.com
State New
Headers show
Series Add QCOM SNPS PHY overriding params support | expand

Commit Message

Krishna Kurapati May 8, 2022, 12:12 p.m. UTC
Add support for overriding electrical signal tuning parameters for
SNPS HS Phy.

Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
---
 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 252 +++++++++++++++++++++++++-
 1 file changed, 250 insertions(+), 2 deletions(-)

Comments

Krishna Kurapati May 10, 2022, 5:34 p.m. UTC | #1
On 5/9/2022 8:48 AM, Pavan Kondeti wrote:
> Hi Krishna,
>
> On Sun, May 08, 2022 at 05:42:26PM +0530, Krishna Kurapati wrote:
>> Add support for overriding electrical signal tuning parameters for
>> SNPS HS Phy.
>>
>> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
>> ---
>>   drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 252 +++++++++++++++++++++++++-
>>   1 file changed, 250 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
>> index 5d20378..bed2c90 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
>> @@ -52,6 +52,12 @@
>>   #define USB2_SUSPEND_N				BIT(2)
>>   #define USB2_SUSPEND_N_SEL			BIT(3)
>>   
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0		(0x6c)
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1		(0x70)
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2		(0x74)
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3		(0x78)
>> +#define PARAM_OVRD_MASK				0xFF
>> +
>>   #define USB2_PHY_USB_PHY_CFG0			(0x94)
>>   #define UTMI_PHY_DATAPATH_CTRL_OVERRIDE_EN	BIT(0)
>>   #define UTMI_PHY_CMN_CTRL_OVERRIDE_EN		BIT(1)
>> @@ -60,6 +66,16 @@
>>   #define REFCLK_SEL_MASK				GENMASK(1, 0)
>>   #define REFCLK_SEL_DEFAULT			(0x2 << 0)
>>   
>> +#define HS_DISCONNECT_MASK			GENMASK(2, 0)
>> +#define SQUELCH_DETECTOR_MASK			GENMASK(7, 5)
>> +#define HS_AMPLITUDE_MASK			GENMASK(3, 0)
>> +#define PREEMPHASIS_DURATION_MASK		BIT(5)
>> +#define PREEMPHASIS_AMPLITUDE_MASK		GENMASK(7, 6)
>> +#define HS_RISE_FALL_MASK			GENMASK(1, 0)
>> +#define HS_CROSSOVER_VOLTAGE_MASK		GENMASK(3, 2)
>> +#define HS_OUTPUT_IMPEDANCE_MASK		GENMASK(5, 4)
>> +#define LS_FS_OUTPUT_IMPEDANCE_MASK		GENMASK(3, 0)
>> +
> LGTM. All these definitions are matching with the databook.
>
>>   static const char * const qcom_snps_hsphy_vreg_names[] = {
>>   	"vdda-pll", "vdda33", "vdda18",
>>   };
>> @@ -173,10 +189,195 @@ static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
>>   	return 0;
>>   }
>>   
>> +struct override_param {
>> +	s32	value;
>> +	u8	reg;
>> +};
>> +
>> +#define OVERRIDE_PARAM(bps, val)\
>> +{				\
>> +	.value = bps,		\
>> +	.reg = val,		\
>> +}
>> +
>> +struct override_param_map {
>> +	struct override_param *param_table;
>> +	u8 table_size;
>> +	u8 reg_offset;
>> +	u8 param_mask;
>> +};
>> +
>> +#define OVERRIDE_PARAM_MAP(table, numElements, offset, mask)		\
> No camelcase please.
>
>> +{									\
>> +	.param_table = table,						\
>> +	.table_size = numElements,					\
>> +	.reg_offset = offset,						\
>> +	.param_mask = mask,						\
>> +}
>> +
>> +static const char *phy_seq_props[] =
>> +{
>> +	"qcom,hs-rise-fall-time-bps",
>> +	"qcom,squelch-detector-bps",
>> +	"qcom,preemphasis-duration",
>> +	"qcom,preemphasis-amplitude",
> What are the units for pre-emphasis duration and amplitude? Can you add the
> units as suffix?
My bad, its bps. Will add it in next patchset.
>> +	"qcom,hs-disconnect-bps",
>> +	"qcom,hs-amplitude-bps",
>> +	"qcom,hs-crossover-voltage",
>> +	"qcom,hs-output-impedance",
> What are the units for these above two parameters?
mV and mohm, Will add them as suffix.
>> +	"qcom,ls-fs-output-impedance-bps",
>> +};
>> +
>> +static struct override_param hs_rise_fall_time_sc7280[] = {
>> +	OVERRIDE_PARAM(-4100, 3),
>> +	OVERRIDE_PARAM(0, 2),
>> +	OVERRIDE_PARAM(2810, 1),
>> +	OVERRIDE_PARAM(5430, 0),
>> +};
>> +
>> +static struct override_param squelch_det_threshold_sc7280[] = {
>> +	OVERRIDE_PARAM(-2090, 7),
>> +	OVERRIDE_PARAM(-1560, 6),
>> +	OVERRIDE_PARAM(-1030, 5),
>> +	OVERRIDE_PARAM(-530, 4),
>> +	OVERRIDE_PARAM(0, 3),
>> +	OVERRIDE_PARAM(530, 2),
>> +	OVERRIDE_PARAM(1060, 1),
>> +	OVERRIDE_PARAM(1590, 0),
>> +};
>> +
>> +static struct override_param hs_disconnect_sc7280[] = {
>> +	OVERRIDE_PARAM(-272, 0),
>> +	OVERRIDE_PARAM(0, 1),
>> +	OVERRIDE_PARAM(317, 2),
>> +	OVERRIDE_PARAM(630, 3),
>> +	OVERRIDE_PARAM(973, 4),
>> +	OVERRIDE_PARAM(1332, 5),
>> +	OVERRIDE_PARAM(1743, 6),
>> +	OVERRIDE_PARAM(2156, 7),
>> +};
>> +
>> +static struct override_param hs_amplitude_sc7280[] = {
>> +	OVERRIDE_PARAM(-660, 0),
>> +	OVERRIDE_PARAM(-440, 1),
>> +	OVERRIDE_PARAM(-220, 2),
>> +	OVERRIDE_PARAM(0, 3),
>> +	OVERRIDE_PARAM(230, 4),
>> +	OVERRIDE_PARAM(440, 5),
>> +	OVERRIDE_PARAM(650, 6),
>> +	OVERRIDE_PARAM(890, 7),
>> +	OVERRIDE_PARAM(1110, 8),
>> +	OVERRIDE_PARAM(1330, 9),
>> +	OVERRIDE_PARAM(1560, 10),
>> +	OVERRIDE_PARAM(1780, 11),
>> +	OVERRIDE_PARAM(2000, 12),
>> +	OVERRIDE_PARAM(2220, 13),
>> +	OVERRIDE_PARAM(2430, 14),
>> +	OVERRIDE_PARAM(2670, 15),
>> +};
>> +
>> +static struct override_param preemphasis_duration_sc7280[] = {
>> +	OVERRIDE_PARAM(100, 1),
>> +	OVERRIDE_PARAM(200, 0),
>> +};
>> +
>> +static struct override_param preemphasis_amplitude_sc7280[] = {
>> +	OVERRIDE_PARAM(100, 1),
>> +	OVERRIDE_PARAM(200, 2),
>> +	OVERRIDE_PARAM(300, 3),
>> +	OVERRIDE_PARAM(400, 0),
>> +};
>> +
>> +static struct override_param hs_crossover_voltage_sc7280[] = {
>> +	OVERRIDE_PARAM(-31, 1),
>> +	OVERRIDE_PARAM(28, 2),
>> +	OVERRIDE_PARAM(0, 3),
>> +};
>> +
>> +static struct override_param hs_output_impedance_sc7280[] = {
>> +	OVERRIDE_PARAM(-2300, 3),
>> +	OVERRIDE_PARAM(0, 2),
>> +	OVERRIDE_PARAM(2600, 1),
>> +	OVERRIDE_PARAM(6100, 0),
>> +};
>> +
>> +static struct override_param ls_fs_output_impedance_sc7280[] = {
>> +	OVERRIDE_PARAM(-1053, 15),
>> +	OVERRIDE_PARAM(-557, 7),
>> +	OVERRIDE_PARAM(0, 3),
>> +	OVERRIDE_PARAM(612, 1),
>> +	OVERRIDE_PARAM(1310, 0),
>> +};
>> +
> LGTM. I have cross checked with the data book.
>
>> +struct override_param_map sc7280_idp[] = {
>> +	OVERRIDE_PARAM_MAP(
>> +			hs_rise_fall_time_sc7280,
>> +			ARRAY_SIZE(hs_rise_fall_time_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
>> +			HS_RISE_FALL_MASK),
>> +
> The bitmask definitions like HS_DISCONNECT_MASK are defined as they appear
> in the databook. However, this struct is defined out of order. Can you
> defined X0, X1, X2 and X3 registers in an order. Easier to check/compare
> against data book.
Sure, Will make this change.
>> +	OVERRIDE_PARAM_MAP(
>> +			squelch_det_threshold_sc7280,
>> +			ARRAY_SIZE(squelch_det_threshold_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0,
>> +			SQUELCH_DETECTOR_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			preemphasis_duration_sc7280,
>> +			ARRAY_SIZE(preemphasis_duration_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
>> +			PREEMPHASIS_DURATION_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			preemphasis_amplitude_sc7280,
>> +			ARRAY_SIZE(preemphasis_amplitude_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
>> +			PREEMPHASIS_AMPLITUDE_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			hs_disconnect_sc7280,
>> +			ARRAY_SIZE(hs_disconnect_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0,
>> +			HS_DISCONNECT_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			hs_amplitude_sc7280,
>> +			ARRAY_SIZE(hs_amplitude_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
>> +			HS_AMPLITUDE_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			hs_crossover_voltage_sc7280,
>> +			ARRAY_SIZE(hs_crossover_voltage_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
>> +			HS_CROSSOVER_VOLTAGE_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			hs_output_impedance_sc7280,
>> +			ARRAY_SIZE(hs_output_impedance_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
>> +			HS_OUTPUT_IMPEDANCE_MASK),
>> +
>> +	OVERRIDE_PARAM_MAP(
>> +			ls_fs_output_impedance_sc7280,
>> +			ARRAY_SIZE(ls_fs_output_impedance_sc7280),
>> +			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3,
>> +			LS_FS_OUTPUT_IMPEDANCE_MASK),
>> +};
>> +
>> +struct phy_override_seq {
>> +	bool	need_update;
>> +	u8	offset;
>> +	u8	value;
>> +	u8	mask;
>> +};
>> +
>> +struct phy_override_seq update_seq_cfg[ARRAY_SIZE(phy_seq_props)];
> This needs to be wrapped up in qcom_snps_hsphy structure so that we can
> support override sequence per phy instance. The electrical complaince tuning
> is heavily influenced by the board design and where the ports are located etc.
> So it is possible that two instances of the phy can use different tunning
> parameters.
Makes sense. Thanks for the correction.
>> +
>>   static int qcom_snps_hsphy_init(struct phy *phy)
>>   {
>>   	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
>> -	int ret;
>> +	int ret, i;
>>   
>>   	dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__);
>>   
>> @@ -223,6 +424,12 @@ static int qcom_snps_hsphy_init(struct phy *phy)
>>   	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1,
>>   					VBUSVLDEXT0, VBUSVLDEXT0);
>>   
>> +	for(i = 0; i < ARRAY_SIZE(update_seq_cfg); i++) {
>> +		if (update_seq_cfg[i].need_update)
>> +			qcom_snps_hsphy_write_mask(hsphy->base, update_seq_cfg[i].offset,
>> +					update_seq_cfg[i].mask, update_seq_cfg[i].value);
>> +	}
>> +
>>   	qcom_snps_hsphy_write_mask(hsphy->base,
>>   					USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2,
>>   					VREGBYPASS, VREGBYPASS);
>> @@ -280,7 +487,10 @@ static const struct phy_ops qcom_snps_hsphy_gen_ops = {
>>   static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
>>   	{ .compatible	= "qcom,sm8150-usb-hs-phy", },
>>   	{ .compatible	= "qcom,usb-snps-hs-5nm-phy", },
>> -	{ .compatible	= "qcom,usb-snps-hs-7nm-phy", },
>> +	{
>> +	.compatible	= "qcom,usb-snps-hs-7nm-phy",
>> +	.data		= &sc7280_idp
>> +	},
> can you check the indentation please?
>
>>   	{ .compatible	= "qcom,usb-snps-femto-v2-phy",	},
>>   	{ }
>>   };
>> @@ -291,6 +501,43 @@ static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
>>   			   qcom_snps_hsphy_runtime_resume, NULL)
>>   };
>>   
>> +static void hsphy_override_param_update_val(const struct override_param_map map,
>> +				s32 dt_val, struct phy_override_seq *seq_entry)
>> +{
>> +	int i;
>> +
>> +	/*
>> +	 * We prepare the param table for each param in increasing order
>> +	 * of dt values. So we need to iterate over the list once to get
>> +	 * the required register value.
>> +	 */
>> +	for (i = 0 ; i < map.table_size-1; i++) {
>> +		if (map.param_table[i].value >= dt_val)
>> +			break;
>> +	}
> The comment is confusing. param_table[] already has values in the increasing
> order. we have to find *closet* match here. To keep it simple, we select the
> entry that has equal or the next highest (round up) value. clarify the
> comment.
Sure.
>> +
>> +	seq_entry->need_update = true;
>> +	seq_entry->offset = map.reg_offset;
>> +	seq_entry->mask = map.param_mask;
>> +	seq_entry->value =  map.param_table[i].reg << __ffs(map.param_mask);
>> +}
>> +
>> +static void phy_read_param_override_seq(struct device *dev)
>> +{
>> +	struct device_node *node = dev->of_node;
>> +	s32 val;
>> +	int ret, i;
>> +	struct qcom_snps_hsphy *hsphy;
>> +	struct override_param_map *cfg = (struct override_param_map* ) of_device_get_match_data(dev);
> nit pick. No explicit type case is needed here. of_device_get_match_data()
> returns a void pointer. so it can be written as
>
> struct override_param_map *cfg = of_device_get_match_data(dev);
>
>> +	hsphy = dev_get_drvdata(dev);
>> +
>> +	for (i = 0; i < ARRAY_SIZE(phy_seq_props); i++) {
>> +		ret = of_property_read_s32(node, phy_seq_props[i], &val);
>> +		if (!ret)
>> +			hsphy_override_param_update_val(cfg[i], val, &update_seq_cfg[i]);
>> +	}
>> +}
>> +
> Can we add a dev_dbg here to aid the debugging?
>
> All the functions defined in this driver has qcom_snps_hsphy_xxxx convention.
> Lets follow the same.
Sure, Will rename the function accordingly.
>>   static int qcom_snps_hsphy_probe(struct platform_device *pdev)
>>   {
>>   	struct device *dev = &pdev->dev;
>> @@ -352,6 +599,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
>>   
>>   	dev_set_drvdata(dev, hsphy);
>>   	phy_set_drvdata(generic_phy, hsphy);
>> +	phy_read_param_override_seq(dev);
>>   
>>   	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>>   	if (!IS_ERR(phy_provider))
>> -- 
>> 2.7.4
>>
> Bjorn/Vinod,
>
> I have reviewed this patch on our internal review system. The basic design
> looks good to me.  Can you please review the patch and provide your inputs.
>
> Thanks,
> Pavan
diff mbox series

Patch

diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
index 5d20378..bed2c90 100644
--- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
+++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
@@ -52,6 +52,12 @@ 
 #define USB2_SUSPEND_N				BIT(2)
 #define USB2_SUSPEND_N_SEL			BIT(3)
 
+#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0		(0x6c)
+#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1		(0x70)
+#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2		(0x74)
+#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3		(0x78)
+#define PARAM_OVRD_MASK				0xFF
+
 #define USB2_PHY_USB_PHY_CFG0			(0x94)
 #define UTMI_PHY_DATAPATH_CTRL_OVERRIDE_EN	BIT(0)
 #define UTMI_PHY_CMN_CTRL_OVERRIDE_EN		BIT(1)
@@ -60,6 +66,16 @@ 
 #define REFCLK_SEL_MASK				GENMASK(1, 0)
 #define REFCLK_SEL_DEFAULT			(0x2 << 0)
 
+#define HS_DISCONNECT_MASK			GENMASK(2, 0)
+#define SQUELCH_DETECTOR_MASK			GENMASK(7, 5)
+#define HS_AMPLITUDE_MASK			GENMASK(3, 0)
+#define PREEMPHASIS_DURATION_MASK		BIT(5)
+#define PREEMPHASIS_AMPLITUDE_MASK		GENMASK(7, 6)
+#define HS_RISE_FALL_MASK			GENMASK(1, 0)
+#define HS_CROSSOVER_VOLTAGE_MASK		GENMASK(3, 2)
+#define HS_OUTPUT_IMPEDANCE_MASK		GENMASK(5, 4)
+#define LS_FS_OUTPUT_IMPEDANCE_MASK		GENMASK(3, 0)
+
 static const char * const qcom_snps_hsphy_vreg_names[] = {
 	"vdda-pll", "vdda33", "vdda18",
 };
@@ -173,10 +189,195 @@  static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
 	return 0;
 }
 
+struct override_param {
+	s32	value;
+	u8	reg;
+};
+
+#define OVERRIDE_PARAM(bps, val)\
+{				\
+	.value = bps,		\
+	.reg = val,		\
+}
+
+struct override_param_map {
+	struct override_param *param_table;
+	u8 table_size;
+	u8 reg_offset;
+	u8 param_mask;
+};
+
+#define OVERRIDE_PARAM_MAP(table, numElements, offset, mask)		\
+{									\
+	.param_table = table,						\
+	.table_size = numElements,					\
+	.reg_offset = offset,						\
+	.param_mask = mask,						\
+}
+
+static const char *phy_seq_props[] =
+{
+	"qcom,hs-rise-fall-time-bps",
+	"qcom,squelch-detector-bps",
+	"qcom,preemphasis-duration",
+	"qcom,preemphasis-amplitude",
+	"qcom,hs-disconnect-bps",
+	"qcom,hs-amplitude-bps",
+	"qcom,hs-crossover-voltage",
+	"qcom,hs-output-impedance",
+	"qcom,ls-fs-output-impedance-bps",
+};
+
+static struct override_param hs_rise_fall_time_sc7280[] = {
+	OVERRIDE_PARAM(-4100, 3),
+	OVERRIDE_PARAM(0, 2),
+	OVERRIDE_PARAM(2810, 1),
+	OVERRIDE_PARAM(5430, 0),
+};
+
+static struct override_param squelch_det_threshold_sc7280[] = {
+	OVERRIDE_PARAM(-2090, 7),
+	OVERRIDE_PARAM(-1560, 6),
+	OVERRIDE_PARAM(-1030, 5),
+	OVERRIDE_PARAM(-530, 4),
+	OVERRIDE_PARAM(0, 3),
+	OVERRIDE_PARAM(530, 2),
+	OVERRIDE_PARAM(1060, 1),
+	OVERRIDE_PARAM(1590, 0),
+};
+
+static struct override_param hs_disconnect_sc7280[] = {
+	OVERRIDE_PARAM(-272, 0),
+	OVERRIDE_PARAM(0, 1),
+	OVERRIDE_PARAM(317, 2),
+	OVERRIDE_PARAM(630, 3),
+	OVERRIDE_PARAM(973, 4),
+	OVERRIDE_PARAM(1332, 5),
+	OVERRIDE_PARAM(1743, 6),
+	OVERRIDE_PARAM(2156, 7),
+};
+
+static struct override_param hs_amplitude_sc7280[] = {
+	OVERRIDE_PARAM(-660, 0),
+	OVERRIDE_PARAM(-440, 1),
+	OVERRIDE_PARAM(-220, 2),
+	OVERRIDE_PARAM(0, 3),
+	OVERRIDE_PARAM(230, 4),
+	OVERRIDE_PARAM(440, 5),
+	OVERRIDE_PARAM(650, 6),
+	OVERRIDE_PARAM(890, 7),
+	OVERRIDE_PARAM(1110, 8),
+	OVERRIDE_PARAM(1330, 9),
+	OVERRIDE_PARAM(1560, 10),
+	OVERRIDE_PARAM(1780, 11),
+	OVERRIDE_PARAM(2000, 12),
+	OVERRIDE_PARAM(2220, 13),
+	OVERRIDE_PARAM(2430, 14),
+	OVERRIDE_PARAM(2670, 15),
+};
+
+static struct override_param preemphasis_duration_sc7280[] = {
+	OVERRIDE_PARAM(100, 1),
+	OVERRIDE_PARAM(200, 0),
+};
+
+static struct override_param preemphasis_amplitude_sc7280[] = {
+	OVERRIDE_PARAM(100, 1),
+	OVERRIDE_PARAM(200, 2),
+	OVERRIDE_PARAM(300, 3),
+	OVERRIDE_PARAM(400, 0),
+};
+
+static struct override_param hs_crossover_voltage_sc7280[] = {
+	OVERRIDE_PARAM(-31, 1),
+	OVERRIDE_PARAM(28, 2),
+	OVERRIDE_PARAM(0, 3),
+};
+
+static struct override_param hs_output_impedance_sc7280[] = {
+	OVERRIDE_PARAM(-2300, 3),
+	OVERRIDE_PARAM(0, 2),
+	OVERRIDE_PARAM(2600, 1),
+	OVERRIDE_PARAM(6100, 0),
+};
+
+static struct override_param ls_fs_output_impedance_sc7280[] = {
+	OVERRIDE_PARAM(-1053, 15),
+	OVERRIDE_PARAM(-557, 7),
+	OVERRIDE_PARAM(0, 3),
+	OVERRIDE_PARAM(612, 1),
+	OVERRIDE_PARAM(1310, 0),
+};
+
+struct override_param_map sc7280_idp[] = {
+	OVERRIDE_PARAM_MAP(
+			hs_rise_fall_time_sc7280,
+			ARRAY_SIZE(hs_rise_fall_time_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
+			HS_RISE_FALL_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			squelch_det_threshold_sc7280,
+			ARRAY_SIZE(squelch_det_threshold_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0,
+			SQUELCH_DETECTOR_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			preemphasis_duration_sc7280,
+			ARRAY_SIZE(preemphasis_duration_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
+			PREEMPHASIS_DURATION_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			preemphasis_amplitude_sc7280,
+			ARRAY_SIZE(preemphasis_amplitude_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
+			PREEMPHASIS_AMPLITUDE_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			hs_disconnect_sc7280,
+			ARRAY_SIZE(hs_disconnect_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0,
+			HS_DISCONNECT_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			hs_amplitude_sc7280,
+			ARRAY_SIZE(hs_amplitude_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
+			HS_AMPLITUDE_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			hs_crossover_voltage_sc7280,
+			ARRAY_SIZE(hs_crossover_voltage_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
+			HS_CROSSOVER_VOLTAGE_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			hs_output_impedance_sc7280,
+			ARRAY_SIZE(hs_output_impedance_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
+			HS_OUTPUT_IMPEDANCE_MASK),
+
+	OVERRIDE_PARAM_MAP(
+			ls_fs_output_impedance_sc7280,
+			ARRAY_SIZE(ls_fs_output_impedance_sc7280),
+			USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3,
+			LS_FS_OUTPUT_IMPEDANCE_MASK),
+};
+
+struct phy_override_seq {
+	bool	need_update;
+	u8	offset;
+	u8	value;
+	u8	mask;
+};
+
+struct phy_override_seq update_seq_cfg[ARRAY_SIZE(phy_seq_props)];
+
 static int qcom_snps_hsphy_init(struct phy *phy)
 {
 	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
-	int ret;
+	int ret, i;
 
 	dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__);
 
@@ -223,6 +424,12 @@  static int qcom_snps_hsphy_init(struct phy *phy)
 	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1,
 					VBUSVLDEXT0, VBUSVLDEXT0);
 
+	for(i = 0; i < ARRAY_SIZE(update_seq_cfg); i++) {
+		if (update_seq_cfg[i].need_update)
+			qcom_snps_hsphy_write_mask(hsphy->base, update_seq_cfg[i].offset,
+					update_seq_cfg[i].mask, update_seq_cfg[i].value);
+	}
+
 	qcom_snps_hsphy_write_mask(hsphy->base,
 					USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2,
 					VREGBYPASS, VREGBYPASS);
@@ -280,7 +487,10 @@  static const struct phy_ops qcom_snps_hsphy_gen_ops = {
 static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
 	{ .compatible	= "qcom,sm8150-usb-hs-phy", },
 	{ .compatible	= "qcom,usb-snps-hs-5nm-phy", },
-	{ .compatible	= "qcom,usb-snps-hs-7nm-phy", },
+	{
+	.compatible	= "qcom,usb-snps-hs-7nm-phy",
+	.data		= &sc7280_idp
+	},
 	{ .compatible	= "qcom,usb-snps-femto-v2-phy",	},
 	{ }
 };
@@ -291,6 +501,43 @@  static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
 			   qcom_snps_hsphy_runtime_resume, NULL)
 };
 
+static void hsphy_override_param_update_val(const struct override_param_map map,
+				s32 dt_val, struct phy_override_seq *seq_entry)
+{
+	int i;
+
+	/*
+	 * We prepare the param table for each param in increasing order
+	 * of dt values. So we need to iterate over the list once to get
+	 * the required register value.
+	 */
+	for (i = 0 ; i < map.table_size-1; i++) {
+		if (map.param_table[i].value >= dt_val)
+			break;
+	}
+
+	seq_entry->need_update = true;
+	seq_entry->offset = map.reg_offset;
+	seq_entry->mask = map.param_mask;
+	seq_entry->value =  map.param_table[i].reg << __ffs(map.param_mask);
+}
+
+static void phy_read_param_override_seq(struct device *dev)
+{
+	struct device_node *node = dev->of_node;
+	s32 val;
+	int ret, i;
+	struct qcom_snps_hsphy *hsphy;
+	struct override_param_map *cfg = (struct override_param_map* ) of_device_get_match_data(dev);
+	hsphy = dev_get_drvdata(dev);
+
+	for (i = 0; i < ARRAY_SIZE(phy_seq_props); i++) {
+		ret = of_property_read_s32(node, phy_seq_props[i], &val);
+		if (!ret)
+			hsphy_override_param_update_val(cfg[i], val, &update_seq_cfg[i]);
+	}
+}
+
 static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -352,6 +599,7 @@  static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 
 	dev_set_drvdata(dev, hsphy);
 	phy_set_drvdata(generic_phy, hsphy);
+	phy_read_param_override_seq(dev);
 
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 	if (!IS_ERR(phy_provider))