mbox series

[v3,0/7] Nuvoton WPCM450 clock and reset driver

Message ID 20220508194333.2170161-1-j.neuschaefer@gmx.net
Headers show
Series Nuvoton WPCM450 clock and reset driver | expand

Message

J. Neuschäfer May 8, 2022, 7:43 p.m. UTC 
This series adds support for the clock and reset controller in the Nuvoton
WPCM450 SoC. This means that the clock rates for peripherals will be calculated
automatically based on the clock tree as it was preconfigured by the bootloader.
The 24 MHz dummy clock, that is currently in the devicetree, is no longer needed.
Somewhat unfortunately, this also means that there is a breaking change once
the devicetree starts relying on the clock driver, but I find it acceptable in
this case, because WPCM450 is still at a somewhat early stage.


Upstreaming plan (although other suggestions are welcome):

Once reviewed,

- The ARM/dts changes should go through Joel Stanley's bmc tree
- The clocksource/timer changes should probably go via Daniel Lezcano and TIP
- The watchdog patch should go via the watchdog tree
- The clock controller bindings and driver should go through the clk tree
- It might make sense to delay the final ARM/dts patch ("ARM: dts: wpcm450:
  Switch clocks to clock controller") until next cycle to make sure it is
  merged after the clock driver.


v3:
- Changed "refclk" string to "ref"
- Fixed some dead code in the driver
- Added clk_prepare_enable call to the watchdog restart handler
- Added a few review tags

v2:
- https://lore.kernel.org/lkml/20220429172030.398011-1-j.neuschaefer@gmx.net/
- various small improvements

v1:
- https://lore.kernel.org/lkml/20220422183012.444674-1-j.neuschaefer@gmx.net/


Jonathan Neuschäfer (7):
  dt-bindings: timer: nuvoton,npcm7xx-timer: Allow specifying all clocks
  clocksource: timer-npcm7xx: Enable timer 1 clock before use
  watchdog: npcm: Enable clock if provided
  dt-bindings: clock: Add Nuvoton WPCM450 clock/reset controller
  ARM: dts: wpcm450: Add clock controller node
  clk: wpcm450: Add Nuvoton WPCM450 clock/reset controller driver
  ARM: dts: wpcm450: Switch clocks to clock controller

 .../bindings/clock/nuvoton,wpcm450-clk.yaml   |  66 ++++
 .../bindings/timer/nuvoton,npcm7xx-timer.yaml |   8 +-
 arch/arm/boot/dts/nuvoton-wpcm450.dtsi        |  29 +-
 drivers/clk/Makefile                          |   1 +
 drivers/clk/clk-wpcm450.c                     | 363 ++++++++++++++++++
 drivers/clocksource/timer-npcm7xx.c           |  10 +
 drivers/reset/Kconfig                         |   2 +-
 drivers/watchdog/npcm_wdt.c                   |  18 +
 .../dt-bindings/clock/nuvoton,wpcm450-clk.h   |  67 ++++
 9 files changed, 555 insertions(+), 9 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/nuvoton,wpcm450-clk.yaml
 create mode 100644 drivers/clk/clk-wpcm450.c
 create mode 100644 include/dt-bindings/clock/nuvoton,wpcm450-clk.h

--
2.35.1

Comments

Krzysztof Kozlowski May 9, 2022, 11:04 a.m. UTC | #1 
On 08/05/2022 21:43, Jonathan Neuschäfer wrote:
> The Nuvoton WPCM450 SoC has a combined clock and reset controller.
> Add a devicetree binding for it, as well as definitions for the bit
> numbers used by it.
> 
> Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
> ---
> 
> v3:
> - Change clock-output-names and clock-names from "refclk" to "ref", suggested
>   by Krzysztof Kozlowski


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>


Best regards,
Krzysztof