| Message ID | 20211130232347.950-1-digetx@gmail.com |
|---|---|
| Headers | show |
| Series | NVIDIA Tegra power management patches for 5.17 | expand |
On Wed, Dec 01, 2021 at 02:23:07AM +0300, Dmitry Osipenko wrote: > This series adds runtime PM support to Tegra drivers and enables core > voltage scaling for Tegra20/30 SoCs, resolving overheating troubles. > > All patches in this series are interdependent and should go via Tegra tree > for simplicity. So these can be applied in any order without breaking anything? Thierry
15.12.2021 18:55, Thierry Reding пишет: > On Wed, Dec 01, 2021 at 02:23:07AM +0300, Dmitry Osipenko wrote: >> This series adds runtime PM support to Tegra drivers and enables core >> voltage scaling for Tegra20/30 SoCs, resolving overheating troubles. >> >> All patches in this series are interdependent and should go via Tegra tree >> for simplicity. > > So these can be applied in any order without breaking anything? Please notice that the word is *inter* dependent, not *in* dependent. There is a build dependency for the patches. The first two "soc/tegra" must be applied first. The "soc/tegra: pmc: Enable core domain support for Tegra20 and Tegra30" *must* be the last applied patch if we want to preserve bisectability. The core voltage scaling can be enabled only once all the drivers got the power management support. The rest could be applied out-of-order.
On Wed, Dec 15, 2021 at 07:11:53PM +0300, Dmitry Osipenko wrote: > 15.12.2021 18:55, Thierry Reding пишет: > > On Wed, Dec 01, 2021 at 02:23:07AM +0300, Dmitry Osipenko wrote: > >> This series adds runtime PM support to Tegra drivers and enables core > >> voltage scaling for Tegra20/30 SoCs, resolving overheating troubles. > >> > >> All patches in this series are interdependent and should go via Tegra tree > >> for simplicity. > > > > So these can be applied in any order without breaking anything? > > Please notice that the word is *inter* dependent, not *in* dependent. > > There is a build dependency for the patches. The first two "soc/tegra" > must be applied first. Okay, so I've separated the first two patches out into a separate stable branch that I can share between the Tegra and drm/tegra trees to pull in the build dependency and then I've applied the driver patches to those two trees and I've verified that the two branches build correctly. I've not done any runtime testing, but I'll trust you on that. > The "soc/tegra: pmc: Enable core domain support for Tegra20 and Tegra30" > *must* be the last applied patch if we want to preserve bisectability. > The core voltage scaling can be enabled only once all the drivers got > the power management support. > > The rest could be applied out-of-order. One last remaining question: I don't think I can apply that one patch if it requires that all the others are enabled first because it would basically create a circular dependency. Can I pick up the final 7 patches (the DT ones) independently of that one patch without things breaking? If so, one option we could try is to wait for both Tegra and drm/tegra trees to get merged into v5.17-rc1 and then send that one patch (which is only a 4-line diff) right after v5.17-rc1 so that it makes it into v5.17-rc2. That avoids the circular dependency and should get everything enabled for v5.17. Do you see any problems with that? Thierry
16.12.2021 16:14, Thierry Reding пишет: > On Wed, Dec 15, 2021 at 07:11:53PM +0300, Dmitry Osipenko wrote: >> 15.12.2021 18:55, Thierry Reding пишет: >>> On Wed, Dec 01, 2021 at 02:23:07AM +0300, Dmitry Osipenko wrote: >>>> This series adds runtime PM support to Tegra drivers and enables core >>>> voltage scaling for Tegra20/30 SoCs, resolving overheating troubles. >>>> >>>> All patches in this series are interdependent and should go via Tegra tree >>>> for simplicity. >>> >>> So these can be applied in any order without breaking anything? >> >> Please notice that the word is *inter* dependent, not *in* dependent. >> >> There is a build dependency for the patches. The first two "soc/tegra" >> must be applied first. > > Okay, so I've separated the first two patches out into a separate stable > branch that I can share between the Tegra and drm/tegra trees to pull in > the build dependency and then I've applied the driver patches to those > two trees and I've verified that the two branches build correctly. I've > not done any runtime testing, but I'll trust you on that. I only compile-tested VIC and NVDEC drivers, but they should be okay, and thus, everything should be good. >> The "soc/tegra: pmc: Enable core domain support for Tegra20 and Tegra30" >> *must* be the last applied patch if we want to preserve bisectability. >> The core voltage scaling can be enabled only once all the drivers got >> the power management support. >> >> The rest could be applied out-of-order. > > One last remaining question: I don't think I can apply that one patch if > it requires that all the others are enabled first because it would > basically create a circular dependency. > > Can I pick up the final 7 patches (the DT ones) independently of that > one patch without things breaking? If so, one option we could try is to > wait for both Tegra and drm/tegra trees to get merged into v5.17-rc1 and > then send that one patch (which is only a 4-line diff) right after > v5.17-rc1 so that it makes it into v5.17-rc2. That avoids the circular > dependency and should get everything enabled for v5.17. > > Do you see any problems with that? Deferring that one patch till v5.17-rc2 will work, thank you.
This series adds runtime PM support to Tegra drivers and enables core voltage scaling for Tegra20/30 SoCs, resolving overheating troubles. All patches in this series are interdependent and should go via Tegra tree for simplicity. Changelog: v16: - Replaced redundant "context->client" with "client" in gr2d/3d RPM patches, which was spotted by Michał Mirosław in v15. - Added new patch that consolidates the RPM management of older UAPI code path. - Added stable tag to "submit: Add missing pm_runtime_mark_last_busy()" patch and reordered it such that it could be backported without merge conflicts. v15: - Added r-b from Ulf Hansson to "soc/tegra: Enable runtime PM during OPP state-syncing" patch and added extra sanity-check to this patch which ensures that RPM is indeed enabled. - Fixed double RPM-disable on unbind for drivers that used devm_pm_runtime_enable() + pm_runtime_force_suspend(). - Added link with additional info to commit message of "regulators: Prepare for suspend" patch. v14: - Fixed missing runtime PM syncing on removal of drivers, which was spotted by Ulf Hansson in v13. - clk-device driver now resumes RPM on system suspend instead of preparing clock which it backs. This was suggested by Ulf Hansson. - clk-device driver now syncs power domain performance unconditionally during driver's probe time since GENPD API allows to do this now. It was spotted by Ulf Hansson. - Added new "Enable runtime PM during OPP state-syncing" patch, which allows drivers to sync state at any time. Previously drivers were obligated to take care of enabling RPM at the "right" time. - Moved runtime PM initialization/uninitialization of DRM drivers that use host1x channel to host1x client init/deinit phase. I noticed that there is UAF problem because RPM-suspend callback waits until channel is idling and channel is already released/freed during driver's removal phase. - Added system suspend support to the new NVDEC DRM driver. - Added missing pm_runtime_mark_last_busy() to DRM driver. - Corrected VDE GENPD patch which previously made video decoder clock always-enabled by mistake if legacy PD code path was used. It was spotted while we were testing VDE on Tegra114 that doesn't support GENPD yet. - Added ack from Peter Chen to the USB patch that he gave to v13. - Changed OPP table names in accordance to the new naming scheme required by the recent core OPP binding. - Added 500MHz memory OPP entry used by ASUS Transformer tablets. v13: - Fixed compile-test error reported by build bot by reverting the mmc/ patch to v11. The sdhci_suspend/resume_host() functions aren't available with the disabled CONFIG_PM_SLEEP, some code needs the ifdef. - Added last r-b from Rob Herring for the DT patches. - Corrected clk/ PM domain-support patch by not using the devm_tegra_core_dev_init_opp_table_common() helper, which I utilized in v12. The clk driver implements its own power domain state syncing and common helper shouldn't be used. This fixes driver probing for some clocks on some devices. It was reported by Svyatoslav Ryhel for PLLE OPP error on T30 Asus Transformer tablet. v12: - Added r-b from Rob Herring to the host1x binding patch. - Added acks from Hans Verkuil to the video decoder patches. - In the v11 changelog I forgot to mention that the clk-binding patch was also changed with a corrected regex pattern and removed 'clocks' sub-node. This patch needs r-b or ack too. - Added new "Rename 3d power domains" patch to match the DT schema naming requirement. Thanks to David Heidelberg for spotting this problem. - Replaced #ifdef CONFIG_PM_SLEEP with maybe_unused in the MMC patch to make code cleaner. v11: - Added acks and r-b from Rob Herring, Mark Brown and Miquel Raynal that were given to v8. - Corrected order of the new memory controller reset entry in device-trees and host1x DT binding patch, which was requested by Rob Herring. - Switched consumer drivers to use power domain state syncing done by new Tegra's common OPP-initialization helper. - Made use of new devm_pm_runtime_enable() helper that was added to v5.15 kernel, where appropriate. - Added "fuse: Use resource-managed helpers" patch. - Converted Tegra20/30 clk drivers to a proper platform drivers, which was requested by Thierry Reding. - Removed clk-bulk API usage from the MMC patch, which was requested by Thierry Reding. - Changed CORE power domain name to "core" in a new patch "Change name of core power domain". - Misc small fixes for problems that I found since v8, like couple typos in error code paths and restored working RPM for Tegra DRM UAPI v1 that was removed in v8 by accident. v9-v10: Figured out remaining GENPD API changes with Ulf Hansson and Viresh Kumar. The OPP-sync helper that was used in v8 isn't needed anymore because GENPD API now allows consumer drivers to init rpm_pstate of power domains. v8: - Added new generic dev_pm_opp_sync() helper that syncs OPP state with hardware. All drivers changed to use it. This replaces GENPD attach_dev callback hacks that were used in v7. - Added new patch patch "soc/tegra: regulators: Prepare for suspend" that fixes dying Tegra20 SoC after enabling VENC power domain during resume from suspend. It matches to what downstream kernel does on suspend/resume. - After a second thought, I dropped patches which added RPM to memory drivers since hardware is always-on and RPM not needed. - Replaced the "dummy host1x driver" patch with new "Disable unused host1x hardware" patch, since it's a cleaner solution. Dmitry Osipenko (40): soc/tegra: Enable runtime PM during OPP state-syncing soc/tegra: Add devm_tegra_core_dev_init_opp_table_common() soc/tegra: Don't print error message when OPPs not available dt-bindings: clock: tegra-car: Document new clock sub-nodes clk: tegra: Support runtime PM and power domain dt-bindings: host1x: Document OPP and power domain properties dt-bindings: host1x: Document Memory Client resets of Host1x, GR2D and GR3D gpu: host1x: Add initial runtime PM and OPP support gpu: host1x: Add host1x_channel_stop() drm/tegra: submit: Add missing pm_runtime_mark_last_busy() drm/tegra: dc: Support OPP and SoC core voltage scaling drm/tegra: hdmi: Add OPP support drm/tegra: gr2d: Support generic power domain and runtime PM drm/tegra: gr3d: Support generic power domain and runtime PM drm/tegra: vic: Stop channel on suspend drm/tegra: nvdec: Stop channel on suspend drm/tegra: submit: Remove pm_runtime_enabled() checks drm/tegra: Consolidate runtime PM management of older UAPI codepath usb: chipidea: tegra: Add runtime PM and OPP support bus: tegra-gmi: Add runtime PM and OPP support pwm: tegra: Add runtime PM and OPP support mmc: sdhci-tegra: Add runtime PM and OPP support mtd: rawnand: tegra: Add runtime PM and OPP support spi: tegra20-slink: Add OPP support media: dt: bindings: tegra-vde: Convert to schema media: dt: bindings: tegra-vde: Document OPP and power domain media: staging: tegra-vde: Support generic power domain soc/tegra: fuse: Reset hardware soc/tegra: fuse: Use resource-managed helpers soc/tegra: regulators: Prepare for suspend soc/tegra: pmc: Rename 3d power domains soc/tegra: pmc: Rename core power domain soc/tegra: pmc: Enable core domain support for Tegra20 and Tegra30 ARM: tegra: Rename CPU and EMC OPP table device-tree nodes ARM: tegra: Add 500MHz entry to Tegra30 memory OPP table ARM: tegra: Add OPP tables and power domains to Tegra20 device-trees ARM: tegra: Add OPP tables and power domains to Tegra30 device-trees ARM: tegra: Add Memory Client resets to Tegra20 GR2D, GR3D and Host1x ARM: tegra: Add Memory Client resets to Tegra30 GR2D, GR3D and Host1x ARM: tegra20/30: Disable unused host1x hardware .../bindings/clock/nvidia,tegra20-car.yaml | 37 + .../display/tegra/nvidia,tegra20-host1x.txt | 53 + .../bindings/media/nvidia,tegra-vde.txt | 64 - .../bindings/media/nvidia,tegra-vde.yaml | 119 ++ arch/arm/boot/dts/tegra124-apalis-emc.dtsi | 4 +- .../arm/boot/dts/tegra124-jetson-tk1-emc.dtsi | 4 +- arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi | 8 +- .../arm/boot/dts/tegra124-nyan-blaze-emc.dtsi | 8 +- .../boot/dts/tegra124-peripherals-opp.dtsi | 140 +- .../boot/dts/tegra20-acer-a500-picasso.dts | 5 +- arch/arm/boot/dts/tegra20-colibri.dtsi | 5 +- .../boot/dts/tegra20-cpu-opp-microvolt.dtsi | 82 +- arch/arm/boot/dts/tegra20-cpu-opp.dtsi | 82 +- arch/arm/boot/dts/tegra20-harmony.dts | 3 +- arch/arm/boot/dts/tegra20-paz00.dts | 3 +- .../arm/boot/dts/tegra20-peripherals-opp.dtsi | 949 +++++++++++- arch/arm/boot/dts/tegra20-seaboard.dts | 3 +- arch/arm/boot/dts/tegra20-tamonten.dtsi | 3 +- arch/arm/boot/dts/tegra20-trimslice.dts | 9 + arch/arm/boot/dts/tegra20-ventana.dts | 1 + arch/arm/boot/dts/tegra20.dtsi | 118 +- .../tegra30-asus-nexus7-grouper-common.dtsi | 1 + ...30-asus-nexus7-grouper-memory-timings.dtsi | 12 +- arch/arm/boot/dts/tegra30-beaver.dts | 1 + arch/arm/boot/dts/tegra30-cardhu.dtsi | 1 + arch/arm/boot/dts/tegra30-colibri.dtsi | 17 +- .../boot/dts/tegra30-cpu-opp-microvolt.dtsi | 144 +- arch/arm/boot/dts/tegra30-cpu-opp.dtsi | 144 +- arch/arm/boot/dts/tegra30-ouya.dts | 5 +- .../arm/boot/dts/tegra30-peripherals-opp.dtsi | 1373 ++++++++++++++++- arch/arm/boot/dts/tegra30.dtsi | 175 ++- drivers/bus/tegra-gmi.c | 50 +- drivers/clk/tegra/Makefile | 1 + drivers/clk/tegra/clk-device.c | 199 +++ drivers/clk/tegra/clk-pll.c | 2 +- drivers/clk/tegra/clk-super.c | 2 +- drivers/clk/tegra/clk-tegra20.c | 77 +- drivers/clk/tegra/clk-tegra30.c | 116 +- drivers/clk/tegra/clk.c | 75 +- drivers/clk/tegra/clk.h | 2 + drivers/gpu/drm/tegra/dc.c | 79 + drivers/gpu/drm/tegra/dc.h | 2 + drivers/gpu/drm/tegra/drm.c | 11 +- drivers/gpu/drm/tegra/gr2d.c | 174 ++- drivers/gpu/drm/tegra/gr3d.c | 353 ++++- drivers/gpu/drm/tegra/hdmi.c | 16 +- drivers/gpu/drm/tegra/nvdec.c | 43 +- drivers/gpu/drm/tegra/submit.c | 14 +- drivers/gpu/drm/tegra/vic.c | 48 +- drivers/gpu/host1x/channel.c | 8 + drivers/gpu/host1x/debug.c | 15 + drivers/gpu/host1x/dev.c | 150 +- drivers/gpu/host1x/dev.h | 3 +- drivers/gpu/host1x/hw/channel_hw.c | 44 +- drivers/gpu/host1x/intr.c | 3 - drivers/gpu/host1x/syncpt.c | 5 +- drivers/mmc/host/sdhci-tegra.c | 81 +- drivers/mtd/nand/raw/tegra_nand.c | 58 +- drivers/pwm/pwm-tegra.c | 82 +- drivers/soc/tegra/common.c | 29 +- drivers/soc/tegra/fuse/fuse-tegra.c | 51 +- drivers/soc/tegra/fuse/fuse-tegra20.c | 33 +- drivers/soc/tegra/fuse/fuse.h | 1 + drivers/soc/tegra/pmc.c | 14 +- drivers/soc/tegra/regulators-tegra20.c | 99 ++ drivers/soc/tegra/regulators-tegra30.c | 122 ++ drivers/spi/spi-tegra20-slink.c | 9 +- drivers/staging/media/tegra-vde/vde.c | 63 +- drivers/usb/chipidea/ci_hdrc_tegra.c | 53 +- include/linux/host1x.h | 1 + include/soc/tegra/common.h | 15 + 71 files changed, 4930 insertions(+), 846 deletions(-) delete mode 100644 Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt create mode 100644 Documentation/devicetree/bindings/media/nvidia,tegra-vde.yaml create mode 100644 drivers/clk/tegra/clk-device.c