| Message ID | 1631637901-11603-1-git-send-email-khsieh@codeaurora.org |
|---|---|
| State | New |
| Headers | show |
| Series | [v4] phy: qcom-qmp: add support for display port voltage and pre-emphasis swing | expand |
Quoting Stephen Boyd (2021-09-14 12:49:13) > Quoting Kuogee Hsieh (2021-09-14 09:45:01) > > Both voltage and pre-emphasis swing level are set during link training > > negotiation between host and sink. There are totally four tables added. > > A voltage swing table for both hbr and hbr1, a voltage table for both > > hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis > > table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is > > added to complete the sequence of configure dp phy base on HPG. > > > > Chnages in v2: > > -- revise commit test > > -- add Fixes tag > > -- replaced voltage_swing_cfg with voltage > > -- replaced pre_emphasis_cfg with emphasis > > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing() > > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing() > > > > Changes in V3: > > -- add __qcom_qmp_phy_configure_dp_swing() to commit swing/pre-emphasis level > > > > Changes in V4: > > -- pass 2D array to __qcom_qmp_phy_configure_dp_swing() > > > > Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") > > Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> > > --- > > Reviewed-by: Stephen Boyd <swboyd@chromium.org> Can this patch be picked up?
On Tue 14 Sep 09:45 PDT 2021, Kuogee Hsieh wrote: $suject says "add support", but afaict the code already configures voltage and pre-emphasis swing. If I understand your change you're not adding support for the swing, but rather you make it possible to have different tables for different versions of the phy? > Both voltage and pre-emphasis swing level are set during link training > negotiation between host and sink. There are totally four tables added. > A voltage swing table for both hbr and hbr1, a voltage table for both > hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis > table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is > added to complete the sequence of configure dp phy base on HPG. > > Chnages in v2: > -- revise commit test > -- add Fixes tag > -- replaced voltage_swing_cfg with voltage > -- replaced pre_emphasis_cfg with emphasis > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing() > -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing() > > Changes in V3: > -- add __qcom_qmp_phy_configure_dp_swing() to commit swing/pre-emphasis level > > Changes in V4: > -- pass 2D array to __qcom_qmp_phy_configure_dp_swing() Carrying the change log as part of the commit message is a DRM specific thing, outside of drivers/gpu this all goes below the '---' below. > > Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") It's not clear to me what issue with aff188feb5e1 this patch fixes. In what way is aff188feb5e1 broken? > Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> > --- > drivers/phy/qualcomm/phy-qcom-qmp.c | 97 +++++++++++++++++++++++++------------ > 1 file changed, 66 insertions(+), 31 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > index 31036aa..fb029e4 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > @@ -3546,12 +3546,17 @@ static const u8 qmp_dp_v3_voltage_swing_hbr_rbr[4][4] = { > { 0x1f, 0xff, 0xff, 0xff } > }; > > -static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, > - unsigned int drv_lvl_reg, unsigned int emp_post_reg) > +static int __qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, > + unsigned int drv_lvl_reg, > + unsigned int emp_post_reg, > + const u8 voltage_swing_hbr_rbr[4][4], > + const u8 pre_emphasis_hbr_rbr[4][4], > + const u8 voltage_swing_hbr3_hbr2[4][4], > + const u8 pre_emphasis_hbr3_hbr2[4][4]) > { > const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; > unsigned int v_level = 0, p_level = 0; > - u8 voltage_swing_cfg, pre_emphasis_cfg; > + u8 voltage, emphasis; > int i; > > for (i = 0; i < dp_opts->lanes; i++) { > @@ -3560,26 +3565,25 @@ static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, > } > > if (dp_opts->link_rate <= 2700) { > - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level]; > - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level]; > + voltage = voltage_swing_hbr_rbr[v_level][p_level]; > + emphasis = pre_emphasis_hbr_rbr[v_level][p_level]; > } else { > - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level]; > - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level]; > + voltage = voltage_swing_hbr3_hbr2[v_level][p_level]; > + emphasis = pre_emphasis_hbr3_hbr2[v_level][p_level]; > } > > /* TODO: Move check to config check */ > - if (voltage_swing_cfg == 0xFF && pre_emphasis_cfg == 0xFF) > + if (voltage == 0xFF && emphasis == 0xFF) > return -EINVAL; > > /* Enable MUX to use Cursor values from these registers */ > - voltage_swing_cfg |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; > - pre_emphasis_cfg |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; > - > - writel(voltage_swing_cfg, qphy->tx + drv_lvl_reg); > - writel(pre_emphasis_cfg, qphy->tx + emp_post_reg); > - writel(voltage_swing_cfg, qphy->tx2 + drv_lvl_reg); > - writel(pre_emphasis_cfg, qphy->tx2 + emp_post_reg); > + voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; > + emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; > > + writel(voltage, qphy->tx + drv_lvl_reg); > + writel(emphasis, qphy->tx + emp_post_reg); > + writel(voltage, qphy->tx2 + drv_lvl_reg); > + writel(emphasis, qphy->tx2 + emp_post_reg); > return 0; > } > > @@ -3588,9 +3592,13 @@ static void qcom_qmp_v3_phy_configure_dp_tx(struct qmp_phy *qphy) > const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; > u32 bias_en, drvr_en; > > - if (qcom_qmp_phy_configure_dp_swing(qphy, > - QSERDES_V3_TX_TX_DRV_LVL, > - QSERDES_V3_TX_TX_EMP_POST1_LVL) < 0) > + if (__qcom_qmp_phy_configure_dp_swing(qphy, > + QSERDES_V3_TX_TX_DRV_LVL, > + QSERDES_V3_TX_TX_EMP_POST1_LVL, > + qmp_dp_v3_voltage_swing_hbr_rbr, > + qmp_dp_v3_pre_emphasis_hbr_rbr, > + qmp_dp_v3_voltage_swing_hbr3_hbr2, > + qmp_dp_v3_pre_emphasis_hbr3_hbr2) < 0) > return; > > if (dp_opts->lanes == 1) { > @@ -3728,6 +3736,35 @@ static int qcom_qmp_v3_dp_phy_calibrate(struct qmp_phy *qphy) > return 0; > } > > +/* The values in these tables are given without MUX_EN (0x20) bit set */ > +static const u8 qmp_dp_v4_pre_emphasis_hbr3_hbr2[4][4] = { > + { 0x00, 0x0c, 0x15, 0x1b }, > + { 0x02, 0x0e, 0x16, 0xff }, > + { 0x02, 0x11, 0xff, 0xff }, > + { 0x04, 0xff, 0xff, 0xff } > +}; > + > +static const u8 qmp_dp_v4_voltage_swing_hbr3_hbr2[4][4] = { > + { 0x02, 0x12, 0x16, 0x1a }, > + { 0x09, 0x19, 0x1f, 0xff }, > + { 0x10, 0x1f, 0xff, 0xff }, > + { 0x1f, 0xff, 0xff, 0xff } > +}; > + > +static const u8 qmp_dp_v4_pre_emphasis_hbr_rbr[4][4] = { > + { 0x00, 0x0e, 0x15, 0x1b }, > + { 0x00, 0x0e, 0x15, 0xff }, > + { 0x00, 0x0e, 0xff, 0xff }, > + { 0x04, 0xff, 0xff, 0xff } > +}; > + > +static const u8 qmp_dp_v4_voltage_swing_hbr_rbr[4][4] = { > + { 0x08, 0x0f, 0x16, 0x1f }, > + { 0x11, 0x1e, 0x1f, 0xff }, > + { 0x16, 0x1f, 0xff, 0xff }, > + { 0x1f, 0xff, 0xff, 0xff } > +}; > + > static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) > { > writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_PSR_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | > @@ -3757,16 +3794,13 @@ static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) > > static void qcom_qmp_v4_phy_configure_dp_tx(struct qmp_phy *qphy) > { > - /* Program default values before writing proper values */ > - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > - > - writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); > - writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); > - > - qcom_qmp_phy_configure_dp_swing(qphy, > + __qcom_qmp_phy_configure_dp_swing(qphy, > QSERDES_V4_TX_TX_DRV_LVL, > - QSERDES_V4_TX_TX_EMP_POST1_LVL); > + QSERDES_V4_TX_TX_EMP_POST1_LVL, > + qmp_dp_v4_voltage_swing_hbr_rbr, > + qmp_dp_v4_pre_emphasis_hbr_rbr, > + qmp_dp_v4_voltage_swing_hbr3_hbr2, > + qmp_dp_v4_pre_emphasis_hbr3_hbr2); > } > > static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) > @@ -3885,6 +3919,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) > writel(drvr1_en, qphy->tx2 + QSERDES_V4_TX_HIGHZ_DRVR_EN); > writel(bias1_en, qphy->tx2 + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN); > > + writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); > + writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); So specifying TX_POL_INV has do be done before we kick off the configuration? This sounds like a real bug fix, separate of the swing settings. Perhaps I'm misunderstanding something with this change? Thanks, Bjorn > + > writel(0x18, qphy->pcs + QSERDES_DP_PHY_CFG); > udelay(2000); > writel(0x19, qphy->pcs + QSERDES_DP_PHY_CFG); > @@ -3896,11 +3933,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) > 10000)) > return -ETIMEDOUT; > > - writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); > - writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); > > - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > + writel(0x22, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); > + writel(0x22, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); > > writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); > writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project >
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index 31036aa..fb029e4 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -3546,12 +3546,17 @@ static const u8 qmp_dp_v3_voltage_swing_hbr_rbr[4][4] = { { 0x1f, 0xff, 0xff, 0xff } }; -static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, - unsigned int drv_lvl_reg, unsigned int emp_post_reg) +static int __qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, + unsigned int drv_lvl_reg, + unsigned int emp_post_reg, + const u8 voltage_swing_hbr_rbr[4][4], + const u8 pre_emphasis_hbr_rbr[4][4], + const u8 voltage_swing_hbr3_hbr2[4][4], + const u8 pre_emphasis_hbr3_hbr2[4][4]) { const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; unsigned int v_level = 0, p_level = 0; - u8 voltage_swing_cfg, pre_emphasis_cfg; + u8 voltage, emphasis; int i; for (i = 0; i < dp_opts->lanes; i++) { @@ -3560,26 +3565,25 @@ static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy, } if (dp_opts->link_rate <= 2700) { - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level]; - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level]; + voltage = voltage_swing_hbr_rbr[v_level][p_level]; + emphasis = pre_emphasis_hbr_rbr[v_level][p_level]; } else { - voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level]; - pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level]; + voltage = voltage_swing_hbr3_hbr2[v_level][p_level]; + emphasis = pre_emphasis_hbr3_hbr2[v_level][p_level]; } /* TODO: Move check to config check */ - if (voltage_swing_cfg == 0xFF && pre_emphasis_cfg == 0xFF) + if (voltage == 0xFF && emphasis == 0xFF) return -EINVAL; /* Enable MUX to use Cursor values from these registers */ - voltage_swing_cfg |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; - pre_emphasis_cfg |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; - - writel(voltage_swing_cfg, qphy->tx + drv_lvl_reg); - writel(pre_emphasis_cfg, qphy->tx + emp_post_reg); - writel(voltage_swing_cfg, qphy->tx2 + drv_lvl_reg); - writel(pre_emphasis_cfg, qphy->tx2 + emp_post_reg); + voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN; + emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN; + writel(voltage, qphy->tx + drv_lvl_reg); + writel(emphasis, qphy->tx + emp_post_reg); + writel(voltage, qphy->tx2 + drv_lvl_reg); + writel(emphasis, qphy->tx2 + emp_post_reg); return 0; } @@ -3588,9 +3592,13 @@ static void qcom_qmp_v3_phy_configure_dp_tx(struct qmp_phy *qphy) const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts; u32 bias_en, drvr_en; - if (qcom_qmp_phy_configure_dp_swing(qphy, - QSERDES_V3_TX_TX_DRV_LVL, - QSERDES_V3_TX_TX_EMP_POST1_LVL) < 0) + if (__qcom_qmp_phy_configure_dp_swing(qphy, + QSERDES_V3_TX_TX_DRV_LVL, + QSERDES_V3_TX_TX_EMP_POST1_LVL, + qmp_dp_v3_voltage_swing_hbr_rbr, + qmp_dp_v3_pre_emphasis_hbr_rbr, + qmp_dp_v3_voltage_swing_hbr3_hbr2, + qmp_dp_v3_pre_emphasis_hbr3_hbr2) < 0) return; if (dp_opts->lanes == 1) { @@ -3728,6 +3736,35 @@ static int qcom_qmp_v3_dp_phy_calibrate(struct qmp_phy *qphy) return 0; } +/* The values in these tables are given without MUX_EN (0x20) bit set */ +static const u8 qmp_dp_v4_pre_emphasis_hbr3_hbr2[4][4] = { + { 0x00, 0x0c, 0x15, 0x1b }, + { 0x02, 0x0e, 0x16, 0xff }, + { 0x02, 0x11, 0xff, 0xff }, + { 0x04, 0xff, 0xff, 0xff } +}; + +static const u8 qmp_dp_v4_voltage_swing_hbr3_hbr2[4][4] = { + { 0x02, 0x12, 0x16, 0x1a }, + { 0x09, 0x19, 0x1f, 0xff }, + { 0x10, 0x1f, 0xff, 0xff }, + { 0x1f, 0xff, 0xff, 0xff } +}; + +static const u8 qmp_dp_v4_pre_emphasis_hbr_rbr[4][4] = { + { 0x00, 0x0e, 0x15, 0x1b }, + { 0x00, 0x0e, 0x15, 0xff }, + { 0x00, 0x0e, 0xff, 0xff }, + { 0x04, 0xff, 0xff, 0xff } +}; + +static const u8 qmp_dp_v4_voltage_swing_hbr_rbr[4][4] = { + { 0x08, 0x0f, 0x16, 0x1f }, + { 0x11, 0x1e, 0x1f, 0xff }, + { 0x16, 0x1f, 0xff, 0xff }, + { 0x1f, 0xff, 0xff, 0xff } +}; + static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) { writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_PSR_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN | @@ -3757,16 +3794,13 @@ static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy) static void qcom_qmp_v4_phy_configure_dp_tx(struct qmp_phy *qphy) { - /* Program default values before writing proper values */ - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); - - writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); - writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL); - - qcom_qmp_phy_configure_dp_swing(qphy, + __qcom_qmp_phy_configure_dp_swing(qphy, QSERDES_V4_TX_TX_DRV_LVL, - QSERDES_V4_TX_TX_EMP_POST1_LVL); + QSERDES_V4_TX_TX_EMP_POST1_LVL, + qmp_dp_v4_voltage_swing_hbr_rbr, + qmp_dp_v4_pre_emphasis_hbr_rbr, + qmp_dp_v4_voltage_swing_hbr3_hbr2, + qmp_dp_v4_pre_emphasis_hbr3_hbr2); } static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) @@ -3885,6 +3919,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) writel(drvr1_en, qphy->tx2 + QSERDES_V4_TX_HIGHZ_DRVR_EN); writel(bias1_en, qphy->tx2 + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN); + writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); + writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); + writel(0x18, qphy->pcs + QSERDES_DP_PHY_CFG); udelay(2000); writel(0x19, qphy->pcs + QSERDES_DP_PHY_CFG); @@ -3896,11 +3933,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy) 10000)) return -ETIMEDOUT; - writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV); - writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV); - writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); - writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); + writel(0x22, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL); + writel(0x22, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL); writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL); writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL);
Both voltage and pre-emphasis swing level are set during link training negotiation between host and sink. There are totally four tables added. A voltage swing table for both hbr and hbr1, a voltage table for both hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is added to complete the sequence of configure dp phy base on HPG. Chnages in v2: -- revise commit test -- add Fixes tag -- replaced voltage_swing_cfg with voltage -- replaced pre_emphasis_cfg with emphasis -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing() -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing() Changes in V3: -- add __qcom_qmp_phy_configure_dp_swing() to commit swing/pre-emphasis level Changes in V4: -- pass 2D array to __qcom_qmp_phy_configure_dp_swing() Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> --- drivers/phy/qualcomm/phy-qcom-qmp.c | 97 +++++++++++++++++++++++++------------ 1 file changed, 66 insertions(+), 31 deletions(-)