diff mbox series

[RFC,4/6] leds: pca955x: Use pinctrl to map GPIOs to pins

Message ID 20210723075858.376378-5-andrew@aj.id.au
State New
Headers show
Series leds: Fix pca955x GPIO pin mappings | expand

Commit Message

Andrew Jeffery July 23, 2021, 7:58 a.m. UTC
The leds-pca955x driver currently assumes that the GPIO numberspace and
the pin numberspace are the same. This quickly falls apart with a
devicetree binding such as the following:

	pca0: pca9552@61 {
		compatible = "nxp,pca9552";
		reg = <0x61>;
		#address-cells = <1>;
		#size-cells = <0>;

		gpio-controller;
		#gpio-cells = <2>;

		led@0 {
			reg = <0>;
			type = <PCA955X_TYPE_LED>;
		};

		gpio@1 {
			reg = <1>;
			type = <PCA955X_TYPE_GPIO>;
		};
	};

This results in a gpiochip with 1 gpio at offset 0 that should control a
pin at offset 1 on the pca9552. Instead the accessing GPIO 0 of the
gpiochip attempts to drive pin 0.

Making the GPIO controller cover the entire chip opens up conflicts
between the LED and GPIO controllers for the pins. What's needed is a
mapping between the GPIO numberspace and the pin numberspace, with
mutually exclusive access to each pin for the LED and GPIO controllers.
Broadly, this is the responsibility of the pinctrl and pinmux
subsystems.

Rework the driver to implement pinctrl and pinmux (despite the lack of
actual mux hardware), and back the gpiochip and LED controller on to the
resulting pin controller.

This effort implements a custom devicetree device mapping callback for
pinctrl to parse maps from the existing devicetree binding for the
PCA955x devices. Subnodes that set `type = <PCA955X_TYPE_LED>`
automatically have a mux group map generated for the default state. This
causes probe() to claim the appropriate LED pins for the LED controller
from the pinctroller. If subnodes of `type = <PCA955X_TYPE_GPIO>` are
specified then the gpiochip implements the correct behaviour for what
the binding intended - an appropriate GPIO pin mapping is generated and
applied to the pincontroller for the specified number of pins.

For future PCA955x devicetree nodes, devices that require a mix of LED
and GPIO pins can specify the number and numberspace mappings with the
`ngpios` and `gpio-ranges` properties from generic GPIO binding. Thus
the only subnodes that need to be specified are those for the LEDs.

The result is that we now have an accurate mapping between GPIO and pin
numberspaces with mutually exclusive access to the pins. In addition,
any pin conflict issues can be resolved through the usual debugfs
properties exposed by the pinctrl subsystem.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
---
 drivers/leds/leds-pca955x.c | 478 +++++++++++++++++++++++++++++++-----
 1 file changed, 422 insertions(+), 56 deletions(-)

Comments

Linus Walleij Aug. 10, 2021, 1:54 p.m. UTC | #1
On Fri, Jul 23, 2021 at 9:59 AM Andrew Jeffery <andrew@aj.id.au> wrote:

> The leds-pca955x driver currently assumes that the GPIO numberspace and

> the pin numberspace are the same. This quickly falls apart with a

> devicetree binding such as the following:

(...)

Honestly I do not understand this patch. It seems to implement a pin
controller and using it in nonstandard ways.

If something implements the pin controller driver API it should be
used as such IMO, externally. This seems to be using it do relay
calls to itself which seems complicated, just invent something
locally in the driver in that case? No need to use pin control?

Can you explain why this LED driver needs to implement a pin
controller?

Yours,
Linus Walleij
Andrew Jeffery Aug. 11, 2021, 12:19 a.m. UTC | #2
On Tue, 10 Aug 2021, at 23:24, Linus Walleij wrote:
> On Fri, Jul 23, 2021 at 9:59 AM Andrew Jeffery <andrew@aj.id.au> wrote:

> 

> > The leds-pca955x driver currently assumes that the GPIO numberspace and

> > the pin numberspace are the same. This quickly falls apart with a

> > devicetree binding such as the following:

> (...)

> 

> Honestly I do not understand this patch. It seems to implement a pin

> controller and using it in nonstandard ways.


Yeah, it's a bit abusive, hence RFC :)

> 

> If something implements the pin controller driver API it should be

> used as such IMO, externally. This seems to be using it do relay

> calls to itself which seems complicated, just invent something

> locally in the driver in that case? No need to use pin control?


Right. After discussions with Andy I'm going to rework the approach to 
GPIOs which will remove a lot of complexity.

The thought was to try to maintain the intent of the devicetree binding 
and use existing APIs, but all-in-all it's ended up twisting things up 
in knots a fair bit. We discard a lot of it by making the gpiochip 
always cover all pins and track use directly in the driver.

> 

> Can you explain why this LED driver needs to implement a pin

> controller?


The short answer is it doesn't as it has none of the associated 
hardware.

I'll cook up something simpler with the aim to avoid non-standard (or 
any) pinctrl.

Andrew
diff mbox series

Patch

diff --git a/drivers/leds/leds-pca955x.c b/drivers/leds/leds-pca955x.c
index 6614291b288e..9e08dbb05bc5 100644
--- a/drivers/leds/leds-pca955x.c
+++ b/drivers/leds/leds-pca955x.c
@@ -45,6 +45,8 @@ 
 #include <linux/leds.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
 #include <linux/property.h>
 #include <linux/slab.h>
 #include <linux/string.h>
@@ -73,6 +75,7 @@  struct pca955x_chipdef {
 	int			bits;
 	u8			slv_addr;	/* 7-bit slave address mask */
 	int			slv_addr_shift;	/* Number of bits to ignore */
+	struct pinctrl_desc	*pinctrl;
 };
 
 struct pca955x {
@@ -80,6 +83,8 @@  struct pca955x {
 	struct pca955x_led *leds;
 	struct pca955x_chipdef	*chipdef;
 	struct i2c_client	*client;
+	struct pinctrl_desc	*pctldesc;
+	struct pinctrl_dev	*pctldev;
 #ifdef CONFIG_LEDS_PCA955X_GPIO
 	struct gpio_chip gpio;
 #endif
@@ -253,6 +258,15 @@  static int pca955x_led_set(struct led_classdev *led_cdev,
 	return ret;
 }
 
+static int
+pca955x_set_pin_value(struct pca955x *pca955x, unsigned int pin, int val)
+{
+	struct led_classdev *cdev = &pca955x->leds[pin].led_cdev;
+	int state = val ? PCA955X_GPIO_HIGH : PCA955X_GPIO_LOW;
+
+	return pca955x_led_set(cdev, state);
+}
+
 #ifdef CONFIG_LEDS_PCA955X_GPIO
 /*
  * Read the INPUT register, which contains the state of LEDs.
@@ -271,64 +285,348 @@  static int pca955x_read_input(struct i2c_client *client, int n, u8 *val)
 
 }
 
-static int pca955x_gpio_request_pin(struct gpio_chip *gc, unsigned int offset)
+static void
+pca955x_gpio_set_value(struct gpio_chip *gc, unsigned int offset, int val)
 {
 	struct pca955x *pca955x = gpiochip_get_data(gc);
-	struct pca955x_led *led = &pca955x->leds[offset];
+	int pin;
 
-	if (led->type == PCA955X_TYPE_GPIO)
-		return 0;
+	pin = pinctrl_gpio_as_pin(pca955x->pctldev, gc->base + offset);
+	if (pin < 0) {
+		dev_err(gc->parent, "Failed to look up pin for GPIO %d\n",
+			offset);
+		return;
+	}
 
-	return -EBUSY;
-}
-
-static int pca955x_set_value(struct gpio_chip *gc, unsigned int offset,
-			     int val)
-{
-	struct pca955x *pca955x = gpiochip_get_data(gc);
-	struct pca955x_led *led = &pca955x->leds[offset];
-
-	if (val)
-		return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_HIGH);
-
-	return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_LOW);
-}
-
-static void pca955x_gpio_set_value(struct gpio_chip *gc, unsigned int offset,
-				   int val)
-{
-	pca955x_set_value(gc, offset, val);
+	pca955x_set_pin_value(pca955x, pin, val);
 }
 
 static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
 {
 	struct pca955x *pca955x = gpiochip_get_data(gc);
-	struct pca955x_led *led = &pca955x->leds[offset];
 	u8 reg = 0;
+	int pin;
+
+	pin = pinctrl_gpio_as_pin(pca955x->pctldev, gc->base + offset);
+	if (pin < 0)
+		return pin;
 
 	/* There is nothing we can do about errors */
-	pca955x_read_input(pca955x->client, led->led_num / 8, &reg);
+	pca955x_read_input(pca955x->client, pin / 8, &reg);
 
-	return !!(reg & (1 << (led->led_num % 8)));
+	return !!(reg & (1 << (pin % 8)));
 }
 
-static int pca955x_gpio_direction_input(struct gpio_chip *gc,
-					unsigned int offset)
+static int
+pca955x_gpio_direction_input(struct gpio_chip *gc, unsigned int offset)
 {
 	struct pca955x *pca955x = gpiochip_get_data(gc);
-	struct pca955x_led *led = &pca955x->leds[offset];
+	struct led_classdev *cdev;
+	int pin;
 
-	/* To use as input ensure pin is not driven. */
-	return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_INPUT);
+	pin = pinctrl_gpio_as_pin(pca955x->pctldev, gc->base + offset);
+	if (pin < 0)
+		return pin;
+
+	cdev = &pca955x->leds[pin].led_cdev;
+
+	return pca955x_led_set(cdev, PCA955X_GPIO_INPUT);
 }
 
-static int pca955x_gpio_direction_output(struct gpio_chip *gc,
-					 unsigned int offset, int val)
+static int
+pca955x_gpio_direction_output(struct gpio_chip *gc, unsigned int offset,
+			      int val)
 {
-	return pca955x_set_value(gc, offset, val);
+	struct pca955x *pca955x = gpiochip_get_data(gc);
+	int pin;
+
+	pin = pinctrl_gpio_as_pin(pca955x->pctldev, gc->base + offset);
+	if (pin < 0)
+		return pin;
+
+	return pca955x_set_pin_value(pca955x, pin, val);
+}
+
+static int
+pca955x_gpio_request_pin(struct gpio_chip *gc, unsigned int offset)
+{
+	return pinctrl_gpio_request(gc->base + offset);
+}
+
+static void
+pca955x_gpio_free_pin(struct gpio_chip *gc, unsigned int offset)
+{
+	int rc;
+
+	/* Go high-impedance */
+	rc = pca955x_gpio_direction_input(gc, offset);
+	if (rc < 0)
+		dev_err(gc->parent, "Failed to set direction for GPIO %u:%u\n", gc->base, offset);
+
+	pinctrl_gpio_free(gc->base + offset);
 }
 #endif /* CONFIG_LEDS_PCA955X_GPIO */
 
+static const struct pinctrl_pin_desc pca9552_pinctrl_pins[] = {
+	PINCTRL_PIN(0, "LED0"),
+	PINCTRL_PIN(1, "LED1"),
+	PINCTRL_PIN(2, "LED2"),
+	PINCTRL_PIN(3, "LED3"),
+	PINCTRL_PIN(4, "LED4"),
+	PINCTRL_PIN(5, "LED5"),
+	PINCTRL_PIN(6, "LED6"),
+	PINCTRL_PIN(7, "LED7"),
+	PINCTRL_PIN(8, "LED8"),
+	PINCTRL_PIN(9, "LED9"),
+	PINCTRL_PIN(10, "LED10"),
+	PINCTRL_PIN(11, "LED11"),
+	PINCTRL_PIN(12, "LED12"),
+	PINCTRL_PIN(13, "LED13"),
+	PINCTRL_PIN(14, "LED14"),
+	PINCTRL_PIN(15, "LED15"),
+};
+
+static const char * const pca9552_groups[] = {
+	"LED0", "LED1", "LED2",  "LED3",  "LED4",  "LED5",  "LED6",  "LED7",
+	"LED8", "LED9", "LED10", "LED11", "LED12", "LED13", "LED14", "LED15",
+};
+
+static const unsigned int pca9552_group_pins[] = {
+	0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,
+};
+
+static const char *pca955x_pinctrl_dev_name(struct pca955x *pca955x)
+{
+	/* The controller is its only consumer via leds and gpios */
+	return dev_name(&pca955x->client->dev);
+}
+
+static int pca955x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+
+	/* We have as many groups as we have LEDs */
+	return pca955x->chipdef->bits;
+}
+
+static const char *
+pca955x_pinctrl_get_group_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+
+	if (unlikely(selector > pca955x->chipdef->bits)) {
+		dev_err(&pca955x->client->dev,
+			"Group selector (%u) exceeds groups count (%u)\n",
+			selector, pca955x->chipdef->bits);
+		return NULL;
+	}
+
+	if (unlikely(selector > ARRAY_SIZE(pca9552_groups))) {
+		dev_err(&pca955x->client->dev,
+			"Group selector (%u) exceeds the supported group count (%u)\n",
+			selector, ARRAY_SIZE(pca9552_groups));
+		return NULL;
+	}
+
+	return pca9552_groups[selector];
+}
+
+static int
+pca955x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, unsigned int  selector,
+			       const unsigned int **pins, unsigned int *num_pins)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+
+	if (unlikely(selector > pca955x->chipdef->bits)) {
+		dev_err(&pca955x->client->dev,
+			"Group selector (%u) exceeds groups count (%u)\n",
+			selector, pca955x->chipdef->bits);
+		return -EINVAL;
+	}
+
+	if (unlikely(selector > ARRAY_SIZE(pca9552_group_pins))) {
+		dev_err(&pca955x->client->dev,
+			"Group selector (%u) exceeds the supported group count (%u)\n",
+			selector, ARRAY_SIZE(pca9552_groups));
+		return -EINVAL;
+	}
+
+	*pins = &pca9552_group_pins[selector];
+	*num_pins = 1;
+
+	return 0;
+}
+
+static int pca955x_pinmux_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return 1;
+}
+
+static const char *
+pca955x_pinmux_get_function_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+
+	if (selector != 0)
+		dev_err(&pca955x->client->dev, "Only the 'LED' function is supported");
+
+	return "LED";
+}
+
+static int pca955x_pinmux_get_function_groups(struct pinctrl_dev *pctldev,
+					      unsigned int selector,
+					      const char * const **groups,
+					      unsigned int *num_groups)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+
+	if (unlikely(pca955x->chipdef->bits > ARRAY_SIZE(pca9552_groups))) {
+		dev_warn(&pca955x->client->dev,
+			 "Unsupported PCA955x configuration, LED count exceed LED group count\n");
+		return -EINVAL;
+	}
+
+	if (selector != 0)
+		dev_err(&pca955x->client->dev, "Only the 'LED' function is supported");
+
+	*groups = &pca9552_groups[0];
+	*num_groups = pca955x->chipdef->bits;
+
+	return 0;
+}
+
+static int
+pca955x_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int func_selector,
+		       unsigned int group_selector)
+{
+	/* There's no actual mux as such. */
+	return 0;
+}
+
+/*
+ * Implement pinctrl map parsing in a way that's backwards compatible with the
+ * existing devicetree binding.
+ */
+static int
+pca955x_dt_dev_to_map(struct pinctrl_dev *pctldev, struct device *dev)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+	struct pinctrl_desc *pctldesc = pca955x->pctldesc;
+	struct fwnode_handle *child;
+	struct pinctrl_map *maps;
+	unsigned int i = 0;
+	int rc;
+
+	if (WARN_ON(dev != &pca955x->client->dev))
+		return -EINVAL;
+
+	/* Only 1 possible mux config per LED, no further allocations needed */
+	maps = devm_kmalloc_array(dev, pca955x->chipdef->bits, sizeof(*maps), GFP_KERNEL);
+	if (!maps)
+		return -ENOMEM;
+
+	device_for_each_child_node(dev, child) {
+		struct pinctrl_map *m;
+		u32 type;
+		u32 reg;
+
+		/* Default to PCA955X_TYPE_LED as we do in pca955x_get_pdata */
+		rc = fwnode_property_read_u32(child, "type", &type);
+		if (rc == -EINVAL)
+			type = PCA955X_TYPE_LED;
+		else if (rc < 0)
+			goto cleanup_maps;
+
+		if (type != PCA955X_TYPE_LED)
+			continue;
+
+		rc = fwnode_property_read_u32(child, "reg", &reg);
+		if (rc < 0)
+			goto cleanup_maps;
+
+		if (i >= pca955x->chipdef->bits) {
+			dev_err(dev,
+				"The number of pin configuration nodes exceeds the number of available pins (%u)\n",
+				pca955x->chipdef->bits);
+			break;
+		}
+
+		m = &maps[i];
+
+		m->dev_name = pctldesc->name;
+		m->name = PINCTRL_STATE_DEFAULT;
+		m->type = PIN_MAP_TYPE_MUX_GROUP;
+		m->ctrl_dev_name = pctldesc->name;
+		m->data.mux.function = "LED";
+		m->data.mux.group = devm_kasprintf(dev, GFP_KERNEL, "LED%d", reg);
+		if (!m->data.mux.group) {
+			rc = -ENOMEM;
+			goto cleanup_maps;
+		}
+
+		i++;
+	}
+
+	/* Trim the map allocation as required */
+	if (i < pca955x->chipdef->bits) {
+		struct pinctrl_map *trimmed;
+
+		trimmed = devm_krealloc(dev, maps, i * sizeof(*maps), GFP_KERNEL);
+		if (trimmed)
+			maps = trimmed;
+		else
+			dev_warn(dev, "Failed to trim pinctrl maps\n");
+	}
+
+	pinctrl_register_mappings(maps, i);
+
+	return 0;
+
+cleanup_maps:
+	while (i--)
+		devm_kfree(dev, maps[i].data.mux.group);
+
+	devm_kfree(dev, maps);
+
+	return rc;
+}
+
+static void
+pca955x_dt_free_map(struct pinctrl_dev *pctldev, struct pinctrl_map *map,
+		    unsigned int num_maps)
+{
+	struct pca955x *pca955x = pinctrl_dev_get_drvdata(pctldev);
+	struct device *dev = &pca955x->client->dev;
+	struct pinctrl_map *iter = map;
+
+	if (!iter)
+		return;
+
+	while (num_maps) {
+		devm_kfree(dev, iter->data.mux.group);
+		iter++;
+		num_maps--;
+	}
+
+	devm_kfree(dev, map);
+}
+
+static const struct pinctrl_ops pca955x_pinctrl_ops = {
+	.get_groups_count	= pca955x_pinctrl_get_groups_count,
+	.get_group_name		= pca955x_pinctrl_get_group_name,
+	.get_group_pins		= pca955x_pinctrl_get_group_pins,
+	.dt_dev_to_map		= pca955x_dt_dev_to_map,
+	.dt_free_map		= pca955x_dt_free_map,
+};
+
+static const struct pinmux_ops pca955x_pinmux_ops = {
+	.get_functions_count	= pca955x_pinmux_get_functions_count,
+	.get_function_name	= pca955x_pinmux_get_function_name,
+	.get_function_groups	= pca955x_pinmux_get_function_groups,
+	.set_mux		= pca955x_pinmux_set_mux,
+	.strict = true,
+};
+
 static struct pca955x_platform_data *
 pca955x_get_pdata(struct i2c_client *client, struct pca955x_chipdef *chip)
 {
@@ -434,7 +732,12 @@  static int pca955x_probe(struct i2c_client *client,
 	struct i2c_adapter *adapter;
 	int i, err;
 	struct pca955x_platform_data *pdata;
-	int ngpios = 0;
+	u32 ngpios = 0;
+	struct fwnode_handle *fwnode;
+
+	fwnode = dev_fwnode(&client->dev);
+	if (!fwnode)
+		return -ENODATA;
 
 	chip = &pca955x_chipdefs[id->driver_data];
 	adapter = client->adapter;
@@ -476,12 +779,35 @@  static int pca955x_probe(struct i2c_client *client,
 	if (!pca955x->leds)
 		return -ENOMEM;
 
+	pca955x->pctldesc = devm_kzalloc(&client->dev,
+			sizeof(*pca955x->pctldesc), GFP_KERNEL);
+	if (!pca955x->pctldesc)
+		return -ENOMEM;
+
 	i2c_set_clientdata(client, pca955x);
 
 	mutex_init(&pca955x->lock);
 	pca955x->client = client;
 	pca955x->chipdef = chip;
 
+	/* pinctrl */
+	pca955x->pctldesc->name = pca955x_pinctrl_dev_name(pca955x);
+	if (!pca955x->pctldesc->name)
+		return -ENOMEM;
+
+	pca955x->pctldesc->pins = &pca9552_pinctrl_pins[0];
+	pca955x->pctldesc->npins = chip->bits;
+	pca955x->pctldesc->pctlops = &pca955x_pinctrl_ops;
+	pca955x->pctldesc->pmxops = &pca955x_pinmux_ops;
+	pca955x->pctldesc->owner = THIS_MODULE;
+
+	err = devm_pinctrl_register_and_init(&client->dev, pca955x->pctldesc,
+					     pca955x, &pca955x->pctldev);
+	if (err) {
+		dev_err(&client->dev, "Failed to register pincontroller: %d\n", err);
+		return err;
+	}
+
 	for (i = 0; i < chip->bits; i++) {
 		pca955x_led = &pca955x->leds[i];
 		pca955x_led->led_num = i;
@@ -527,6 +853,12 @@  static int pca955x_probe(struct i2c_client *client,
 		}
 	}
 
+	err = pinctrl_enable(pca955x->pctldev);
+	if (err) {
+		dev_err(&client->dev, "Failed to enable pincontroller: %d\n", err);
+		return err;
+	}
+
 	/* PWM0 is used for half brightness or 50% duty cycle */
 	err = pca955x_write_pwm(client, 0, 255 - LED_HALF);
 	if (err)
@@ -546,30 +878,64 @@  static int pca955x_probe(struct i2c_client *client,
 		return err;
 
 #ifdef CONFIG_LEDS_PCA955X_GPIO
-	if (ngpios) {
-		pca955x->gpio.label = "gpio-pca955x";
-		pca955x->gpio.direction_input = pca955x_gpio_direction_input;
-		pca955x->gpio.direction_output = pca955x_gpio_direction_output;
-		pca955x->gpio.set = pca955x_gpio_set_value;
-		pca955x->gpio.get = pca955x_gpio_get_value;
-		pca955x->gpio.request = pca955x_gpio_request_pin;
-		pca955x->gpio.can_sleep = 1;
-		pca955x->gpio.base = -1;
-		pca955x->gpio.ngpio = ngpios;
-		pca955x->gpio.parent = &client->dev;
-		pca955x->gpio.owner = THIS_MODULE;
+	/* Always register the gpiochip, no-longer conditional on ngpios */
+	pca955x->gpio.label = "gpio-pca955x";
+	pca955x->gpio.direction_input = pca955x_gpio_direction_input;
+	pca955x->gpio.direction_output = pca955x_gpio_direction_output;
+	pca955x->gpio.set = pca955x_gpio_set_value;
+	pca955x->gpio.get = pca955x_gpio_get_value;
+	pca955x->gpio.request = pca955x_gpio_request_pin;
+	pca955x->gpio.free = pca955x_gpio_free_pin;
+	pca955x->gpio.can_sleep = 1;
+	pca955x->gpio.base = -1;
+	pca955x->gpio.parent = &client->dev;
+	pca955x->gpio.owner = THIS_MODULE;
 
-		err = devm_gpiochip_add_data(&client->dev, &pca955x->gpio,
-					     pca955x);
-		if (err) {
-			/* Use data->gpio.dev as a flag for freeing gpiochip */
-			pca955x->gpio.parent = NULL;
-			dev_warn(&client->dev, "could not add gpiochip\n");
+	if (!ngpios) {
+		err = fwnode_property_read_u32(fwnode, "ngpios", &ngpios);
+		if (err < 0 && err != -EINVAL)
 			return err;
+	}
+
+	if (!ngpios)
+		ngpios = chip->bits;
+
+
+	pca955x->gpio.ngpio = ngpios;
+
+	err = devm_gpiochip_add_data(&client->dev, &pca955x->gpio, pca955x);
+	if (err) {
+		/* Use data->gpio.dev as a flag for freeing gpiochip */
+		pca955x->gpio.parent = NULL;
+		dev_warn(&client->dev, "could not add gpiochip\n");
+		return err;
+	}
+
+	if (!device_property_present(&client->dev, "gpio-ranges")) {
+		struct fwnode_handle *child;
+		unsigned int i = 0;
+
+		device_for_each_child_node(&client->dev, child) {
+			u32 type;
+			u32 reg;
+
+			err = fwnode_property_read_u32(child, "reg", &reg);
+			if (err < 0)
+				return err;
+
+			err = fwnode_property_read_u32(child, "type", &type);
+			if (err < 0)
+				continue;
+
+			/* XXX: Do something less wasteful? */
+			err = gpiochip_add_pin_range(&pca955x->gpio,
+					pca955x_pinctrl_dev_name(pca955x),
+					i, reg, 1);
+			if (err)
+				return err;
+
+			i++;
 		}
-		dev_info(&client->dev, "gpios %i...%i\n",
-			 pca955x->gpio.base, pca955x->gpio.base +
-			 pca955x->gpio.ngpio - 1);
 	}
 #endif