Message ID | 1626853288-31223-4-git-send-email-dillon.minfei@gmail.com |
---|---|
State | Superseded |
Headers | show |
Series | Add ilitek ili9341 panel driver | expand |
On Wed, Jul 21, 2021 at 9:41 AM <dillon.minfei@gmail.com> wrote: > From: Dillon Min <dillon.minfei@gmail.com> > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > with mipi_dpi_interface driver, can support ili9341 with serial > mode or parallel rgb interface mode by register configuration. > > Cc: Linus Walleij <linus.walleij@linaro.org> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > --- > changes in v2: > - replace vcc regulator to three bulk regulators(vci, vddi, vddi-led) > according to linus suggestion, thanks. This is a really nice driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Yours, Linus Walleij
On Wed, Jul 21, 2021 at 1:11 PM <dillon.minfei@gmail.com> wrote: > > From: Dillon Min <dillon.minfei@gmail.com> > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > with mipi_dpi_interface driver, can support ili9341 with serial > mode or parallel rgb interface mode by register configuration. > > Cc: Linus Walleij <linus.walleij@linaro.org> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > --- > changes in v2: > - replace vcc regulator to three bulk regulators(vci, vddi, vddi-led) > according to linus suggestion, thanks. > > drivers/gpu/drm/panel/Kconfig | 12 + > drivers/gpu/drm/panel/Makefile | 1 + > drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 778 +++++++++++++++++++++++++++ > 3 files changed, 791 insertions(+) > create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > index ef87d92cdf49..eb34b8d1b19a 100644 > --- a/drivers/gpu/drm/panel/Kconfig > +++ b/drivers/gpu/drm/panel/Kconfig > @@ -124,6 +124,18 @@ config DRM_PANEL_ILITEK_IL9322 > Say Y here if you want to enable support for Ilitek IL9322 > QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. > > +config DRM_PANEL_ILITEK_ILI9341 > + tristate "Ilitek ILI9341 240x320 QVGA panels" > + depends on OF && SPI > + depends on DRM_KMS_HELPER > + depends on DRM_KMS_CMA_HELPER > + depends on BACKLIGHT_CLASS_DEVICE > + select DRM_MIPI_DBI > + help > + Say Y here if you want to enable support for Ilitek IL9341 > + QVGA (240x320) RGB panels. support serial & parallel rgb > + interface. > + > config DRM_PANEL_ILITEK_ILI9881C > tristate "Ilitek ILI9881C-based panels" > depends on OF > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > index cae4d976c069..0ecde184665d 100644 > --- a/drivers/gpu/drm/panel/Makefile > +++ b/drivers/gpu/drm/panel/Makefile > @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o > obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o > obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o > obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o > +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o > obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o > obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o > obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > new file mode 100644 > index 000000000000..717b0b930e2f > --- /dev/null > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > @@ -0,0 +1,778 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Ilitek ILI9341 TFT LCD drm_panel driver. > + * > + * This panel can be configured to support: > + * - 16-bit parallel RGB interface > + * - 18-bit parallel RGB interface > + * - 4-line serial spi interface > + * > + * Copyright (C) 2021 Dillon Min <dillon.minfei@gmail.com> > + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c > + * the reuse of DBI abstraction part referred from Linus's patch > + * "drm/panel: s6e63m0: Switch to DBI abstraction for SPI" > + */ > + > +#include <linux/bitops.h> > +#include <linux/gpio/consumer.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/regulator/consumer.h> > +#include <linux/spi/spi.h> > +#include <linux/delay.h> > +#include <video/mipi_display.h> > +#include <drm/drm_mipi_dbi.h> > +#include <drm/drm_gem_framebuffer_helper.h> > +#include <drm/drm_gem_cma_helper.h> > +#include <drm/drm_fb_helper.h> > +#include <drm/drm_atomic_helper.h> > +#include <drm/drm_gem_atomic_helper.h> > + > +#include <drm/drm_drv.h> > +#include <drm/drm_modes.h> > +#include <drm/drm_panel.h> > +#include <drm/drm_print.h> > + > +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ > +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ > +#define ILI9341_DFC 0xb6 /* Display Function Control register */ > +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ > +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ > +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ > +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ > +#define ILI9341_POWERA 0xcb /* Power control A register */ > +#define ILI9341_POWERB 0xcf /* Power control B register */ > +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ > +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ > +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ > +#define ILI9341_DTCB 0xea /* Driver timing control B */ > +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ > +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ > +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ > +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ > +#define ILI9341_ETMOD 0xb7 /* Entry mode set */ > + > +#define ILI9341_MADCTL_BGR BIT(3) > +#define ILI9341_MADCTL_MV BIT(5) > +#define ILI9341_MADCTL_MX BIT(6) > +#define ILI9341_MADCTL_MY BIT(7) > + > +#define ILI9341_POWER_B_LEN 3 > +#define ILI9341_POWER_SEQ_LEN 4 > +#define ILI9341_DTCA_LEN 3 > +#define ILI9341_DTCB_LEN 2 > +#define ILI9341_POWER_A_LEN 5 > +#define ILI9341_DFC_1_LEN 2 > +#define ILI9341_FRC_LEN 2 > +#define ILI9341_VCOM_1_LEN 2 > +#define ILI9341_DFC_2_LEN 4 > +#define ILI9341_COLUMN_ADDR_LEN 4 > +#define ILI9341_PAGE_ADDR_LEN 4 > +#define ILI9341_INTERFACE_LEN 3 > +#define ILI9341_PGAMMA_LEN 15 > +#define ILI9341_NGAMMA_LEN 15 > +#define ILI9341_CA_LEN 3 > + > +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6) | BIT(4)) > +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6) | BIT(5)) > +#define ILI9341_GAMMA_CURVE_1 BIT(0) > +#define ILI9341_IF_WE_MODE BIT(0) > +#define ILI9341_IF_BIG_ENDIAN 0x00 > +#define ILI9341_IF_DM_RGB BIT(2) > +#define ILI9341_IF_DM_INTERNAL 0x00 > +#define ILI9341_IF_DM_VSYNC BIT(3) > +#define ILI9341_IF_RM_RGB BIT(1) > +#define ILI9341_IF_RIM_RGB 0x00 > + > +#define ILI9341_COLUMN_ADDR 0x00ef > +#define ILI9341_PAGE_ADDR 0x013f > + > +#define ILI9341_RGB_EPL BIT(0) > +#define ILI9341_RGB_DPL BIT(1) > +#define ILI9341_RGB_HSPL BIT(2) > +#define ILI9341_RGB_VSPL BIT(3) > +#define ILI9341_RGB_DE_MODE BIT(6) > +#define ILI9341_RGB_DISP_PATH_MEM BIT(7) > + > +#define ILI9341_DBI_VCOMH_4P6V 0x23 > +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 > +#define ILI9341_DBI_PRC_NORMAL 0x20 > +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e > +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 > +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 > +#define ILI9341_DBI_FRC_DIVA 0x00 > +#define ILI9341_DBI_FRC_RTNA 0x1b > +#define ILI9341_DBI_EMS_GAS BIT(0) > +#define ILI9341_DBI_EMS_DTS BIT(1) > +#define ILI9341_DBI_EMS_GON BIT(2) > + > +/** > + * struct ili9341_config - the system specific ILI9341 configuration > + * @max_spi_speed: 10000000 > + */ > +struct ili9341_config { > + u32 max_spi_speed; > + /** @mode: the drm display mode */ > + const struct drm_display_mode mode; > + /** @ca: TODO: need comments for this register */ > + u8 ca[ILI9341_CA_LEN]; > + /** @power_b: TODO: need comments for this register */ > + u8 power_b[ILI9341_POWER_B_LEN]; > + /** @power_seq: TODO: need comments for this register */ > + u8 power_seq[ILI9341_POWER_SEQ_LEN]; > + /** @dtca: TODO: need comments for this register */ > + u8 dtca[ILI9341_DTCA_LEN]; > + /** @dtcb: TODO: need comments for this register */ > + u8 dtcb[ILI9341_DTCB_LEN]; > + /** @power_a: TODO: need comments for this register */ > + u8 power_a[ILI9341_POWER_A_LEN]; > + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ > + u8 frc[ILI9341_FRC_LEN]; > + /** @prc: TODO: need comments for this register */ > + u8 prc; > + /** @dfc_1: B6h DISCTRL (Display Function Control) */ > + u8 dfc_1[ILI9341_DFC_1_LEN]; > + /** @power_1: Power Control 1 (C0h) */ > + u8 power_1; > + /** @power_2: Power Control 2 (C1h) */ > + u8 power_2; > + /** @vcom_1: VCOM Control 1(C5h) */ > + u8 vcom_1[ILI9341_VCOM_1_LEN]; > + /** @vcom_2: VCOM Control 2(C7h) */ > + u8 vcom_2; > + /** @address_mode: Memory Access Control (36h) */ > + u8 address_mode; > + /** @g3amma_en: TODO: need comments for this register */ > + u8 g3amma_en; > + /** @rgb_interface: RGB Interface Signal Control (B0h) */ > + u8 rgb_interface; > + /** @dfc_2: refer to dfc_1 */ > + u8 dfc_2[ILI9341_DFC_2_LEN]; > + /** @column_addr: Column Address Set (2Ah) */ > + u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; > + /** @page_addr: Page Address Set (2Bh) */ > + u8 page_addr[ILI9341_PAGE_ADDR_LEN]; > + /** @interface: Interface Control (F6h) */ > + u8 interface[ILI9341_INTERFACE_LEN]; > + /** @pixel_format: This command sets the pixel format for the RGB */ > + /* image data used by > + */ > + u8 pixel_format; > + /** @gamma_curve: This command is used to select the desired Gamma */ > + /* curve for the > + */ > + u8 gamma_curve; > + /** @pgamma: Positive Gamma Correction (E0h) */ > + u8 pgamma[ILI9341_PGAMMA_LEN]; > + /** @ngamma: Negative Gamma Correction (E1h) */ > + u8 ngamma[ILI9341_NGAMMA_LEN]; > +}; > + > +struct ili9341 { > + struct device *dev; > + const struct ili9341_config *conf; > + struct drm_panel panel; > + struct gpio_desc *reset_gpio; > + struct gpio_desc *dc_gpio; > + struct mipi_dbi *dbi; > + u32 max_spi_speed; > + struct regulator_bulk_data supplies[3]; > +}; > + > +/* > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller > + */ > +static const struct ili9341_config ili9341_stm32f429_disco_data = { > + .max_spi_speed = 10000000, > + .mode = { > + .clock = 6100, > + .hdisplay = 240, > + .hsync_start = 240 + 10,/* hfp 10 */ > + .hsync_end = 240 + 10 + 10,/* hsync 10 */ > + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ > + .vdisplay = 320, > + .vsync_start = 320 + 4,/* vfp 4 */ > + .vsync_end = 320 + 4 + 2,/* vsync 2 */ > + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ > + .flags = 0, > + .width_mm = 65, > + .height_mm = 50, > + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, > + }, > + .ca = {0xc3, 0x08, 0x50}, > + .power_b = {0x00, 0xc1, 0x30}, > + .power_seq = {0x64, 0x03, 0x12, 0x81}, > + .dtca = {0x85, 0x00, 0x78}, > + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, > + .prc = 0x20, > + .dtcb = {0x00, 0x00}, > + /* 0x00 fosc, 0x1b 70hz */ > + .frc = {0x00, 0x1b}, > + /* 0x0a Interval scan, AGND AGND AGND AGND > + * 0xa2 Normally white, G1 -> G320, S720 -> S1, > + * Scan Cycle 5 frames,85ms > + */ > + .dfc_1 = {0x0a, 0xa2}, > + /* 0x10 3.65v */ > + .power_1 = 0x10, > + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ > + .power_2 = 0x10, > + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ > + .vcom_1 = {0x45, 0x15}, > + /* 0x90 offset voltage, VMH-48, VML-48 */ > + .vcom_2 = 0x90, > + /* 0xc8 Row Address Order, Column Address Order > + * BGR 1 > + */ > + .address_mode = 0xc8, > + .g3amma_en = 0x00, > + /* 0xc2 > + * Display Data Path: Memory > + * RGB: DE mode > + * DOTCLK polarity set (data fetched at the falling time) > + */ > + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | > + ILI9341_RGB_DE_MODE | > + ILI9341_RGB_DPL, > + /* > + * 0x0a > + * Gate outputs in non-display area: Interval scan > + * Determine source/VCOM output in a non-display area in the partial > + * display mode: AGND AGND AGND AGND > + * > + * 0xa7 > + * Scan Cycle: 15 frames > + * fFLM = 60Hz: 255ms > + * Liquid crystal type: Normally white > + * Gate Output Scan Direction: G1 -> G320 > + * Source Output Scan Direction: S720 -> S1 > + * > + * 0x27 > + * LCD Driver Line: 320 lines > + * > + * 0x04 > + * PCDIV: 4 > + */ > + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, > + /* column address: 240 */ > + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, > + ILI9341_COLUMN_ADDR & 0xff}, > + /* page address: 320 */ > + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, > + ILI9341_PAGE_ADDR & 0xff}, > + /* Memory write control: When the transfer number of data exceeds > + * (EC-SC+1)*(EP-SP+1), the column and page number will be > + * reset, and the exceeding data will be written into the following > + * column and page. > + * Display Operation Mode: RGB Interface Mode > + * Interface for RAM Access: RGB interface > + * 16- bit RGB interface (1 transfer/pixel) > + */ > + .interface = {ILI9341_IF_WE_MODE, 0x00, > + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, > + /* DPI: 16 bits / pixel */ > + .pixel_format = ILI9341_PIXEL_DPI_16_BITS, > + /* Curve Selected: Gamma curve 1 (G2.2) */ > + .gamma_curve = ILI9341_GAMMA_CURVE_1, > + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, > + 0x09, 0x4e, 0x78, 0x3c, 0x09, > + 0x13, 0x05, 0x17, 0x11, 0x00}, > + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, > + 0x07, 0x31, 0x33, 0x42, 0x05, > + 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, > +}; > + > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) > +{ > + return container_of(panel, struct ili9341, panel); > +} > + > +static void ili9341_dpi_init(struct ili9341 *ili) > +{ > + struct mipi_dbi *dbi = ili->dbi; > + struct ili9341_config *cfg = (struct ili9341_config *)ili->conf; > + > + /* Power Control */ > + mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b, > + ILI9341_POWER_B_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq, > + ILI9341_POWER_SEQ_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca, > + ILI9341_DTCA_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a, > + ILI9341_POWER_A_LEN); > + mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc); > + mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb, > + ILI9341_DTCB_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1, > + ILI9341_DFC_1_LEN); > + mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1); > + mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2); > + > + /* VCOM */ > + mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1, > + ILI9341_VCOM_1_LEN); > + mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2); > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode); > + > + /* Gamma */ > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en); > + mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface); > + mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2, > + ILI9341_DFC_2_LEN); > + > + /* Colomn address set */ > + mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS, > + cfg->column_addr, ILI9341_COLUMN_ADDR_LEN); > + > + /* Page address set */ > + mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS, > + cfg->page_addr, ILI9341_PAGE_ADDR_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface, > + ILI9341_INTERFACE_LEN); > + > + /* Format */ > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format); > + mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); > + msleep(200); > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve); > + mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma, > + ILI9341_PGAMMA_LEN); > + mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma, > + ILI9341_NGAMMA_LEN); > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); > + msleep(200); > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); > + mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); > + > + dev_info(ili->dev, "initialized display rgb interface\n"); > +} > + > +static int ili9341_dpi_power_on(struct ili9341 *ili) > +{ > + int ret = 0; > + > + /* Assert RESET */ > + gpiod_set_value(ili->reset_gpio, 1); > + > + /* Enable power */ > + ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies), > + ili->supplies); > + if (ret < 0) { > + dev_err(ili->dev, "unable to enable vcc\n"); > + return ret; > + } > + msleep(20); > + > + /* De-assert RESET */ > + gpiod_set_value(ili->reset_gpio, 0); > + msleep(20); > + > + return 0; > +} > + > +static int ili9341_dpi_power_off(struct ili9341 *ili) > +{ > + /* Assert RESET */ > + gpiod_set_value(ili->reset_gpio, 1); > + > + /* Disable power */ > + return regulator_bulk_disable(ARRAY_SIZE(ili->supplies), > + ili->supplies); > +} > + > +static int ili9341_dpi_disable(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + > + mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF); > + return 0; > +} > + > +static int ili9341_dpi_unprepare(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + > + return ili9341_dpi_power_off(ili); > +} > + > +static int ili9341_dpi_prepare(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + int ret; > + > + ret = ili9341_dpi_power_on(ili); > + if (ret < 0) > + return ret; > + > + ili9341_dpi_init(ili); > + > + return ret; > +} > + > +static int ili9341_dpi_enable(struct drm_panel *panel) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + > + mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON); > + return 0; > +} > + > +static int ili9341_dpi_get_modes(struct drm_panel *panel, > + struct drm_connector *connector) > +{ > + struct ili9341 *ili = panel_to_ili9341(panel); > + struct drm_device *drm = connector->dev; > + struct drm_display_mode *mode; > + struct drm_display_info *info; > + > + info = &connector->display_info; > + info->width_mm = ili->conf->mode.width_mm; > + info->height_mm = ili->conf->mode.height_mm; > + > + if (ili->conf->rgb_interface & ILI9341_RGB_DPL) > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; > + else > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; > + > + if (ili->conf->rgb_interface & ILI9341_RGB_EPL) > + info->bus_flags |= DRM_BUS_FLAG_DE_LOW; > + else > + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; > + > + mode = drm_mode_duplicate(drm, &ili->conf->mode); > + if (!mode) { > + DRM_ERROR("bad mode or failed to add mode\n"); > + return -EINVAL; > + } > + drm_mode_set_name(mode); > + > + /* Set up the polarity */ > + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) > + mode->flags |= DRM_MODE_FLAG_PHSYNC; > + else > + mode->flags |= DRM_MODE_FLAG_NHSYNC; > + > + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) > + mode->flags |= DRM_MODE_FLAG_PVSYNC; > + else > + mode->flags |= DRM_MODE_FLAG_NVSYNC; > + > + drm_mode_probed_add(connector, mode); > + > + return 1; /* Number of modes */ > +} > + > +static const struct drm_panel_funcs ili9341_dpi_funcs = { > + .disable = ili9341_dpi_disable, > + .unprepare = ili9341_dpi_unprepare, > + .prepare = ili9341_dpi_prepare, > + .enable = ili9341_dpi_enable, > + .get_modes = ili9341_dpi_get_modes, > +}; > + > +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, > + struct drm_crtc_state *crtc_state, > + struct drm_plane_state *plane_state) > +{ > + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); > + struct mipi_dbi *dbi = &dbidev->dbi; > + u8 addr_mode; > + int ret, idx; > + > + if (!drm_dev_enter(pipe->crtc.dev, &idx)) > + return; > + > + DRM_DEBUG_KMS("\n"); > + > + ret = mipi_dbi_poweron_conditional_reset(dbidev); > + if (ret < 0) > + goto out_exit; > + if (ret == 1) > + goto out_enable; > + > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); > + > + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); > + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); > + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); > + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); > + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); > + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); > + > + /* Power Control */ > + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); > + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); > + /* VCOM */ > + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, > + ILI9341_DBI_VCOM_1_VML_1P5V); > + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); > + > + /* Memory Access Control */ > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, > + MIPI_DCS_PIXEL_FMT_16BIT); > + > + /* Frame Rate */ > + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, > + ILI9341_DBI_FRC_RTNA & 0x1f); > + > + /* Gamma */ > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); > + mipi_dbi_command(dbi, ILI9341_PGAMMA, > + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, > + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); > + mipi_dbi_command(dbi, ILI9341_NGAMMA, > + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, > + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); > + > + /* DDRAM */ > + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | > + ILI9341_DBI_EMS_DTS | > + ILI9341_DBI_EMS_GON); > + > + /* Display */ > + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); > + msleep(100); > + > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); > + msleep(100); > + > +out_enable: > + switch (dbidev->rotation) { > + default: > + addr_mode = ILI9341_MADCTL_MX; > + break; > + case 90: > + addr_mode = ILI9341_MADCTL_MV; > + break; > + case 180: > + addr_mode = ILI9341_MADCTL_MY; > + break; > + case 270: > + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | > + ILI9341_MADCTL_MX; > + break; > + } > + addr_mode |= ILI9341_MADCTL_BGR; > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); > + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); > + DRM_DEBUG_KMS("initialized display serial interface\n"); > +out_exit: > + drm_dev_exit(idx); > +} > + > +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { > + .enable = ili9341_dbi_enable, > + .disable = mipi_dbi_pipe_disable, > + .update = mipi_dbi_pipe_update, > + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb, > +}; > + > +static const struct drm_display_mode ili9341_dbi_mode = { > + DRM_SIMPLE_MODE(240, 320, 37, 49), > +}; > + > +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops); > + > +static struct drm_driver ili9341_dbi_driver = { > + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, > + .fops = &ili9341_dbi_fops, > + DRM_GEM_CMA_DRIVER_OPS_VMAP, > + .debugfs_init = mipi_dbi_debugfs_init, > + .name = "ili9341", > + .desc = "Ilitek ILI9341", > + .date = "20210716", > + .major = 1, > + .minor = 0, > +}; > + > +static int _ili9341_probe(struct spi_device *spi, bool dpi) > +{ > + struct gpio_desc *dc; > + struct gpio_desc *reset; > + struct device *dev = &spi->dev; > + int ret; > + > + reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); > + if (IS_ERR(reset)) > + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); > + > + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); > + if (IS_ERR(dc)) > + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); Small nit. Moving the above dts parse code into the main probe and have functions for dpi and !dpi would make code more readable. Otherwise, Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Den 21.07.2021 09.41, skrev dillon.minfei@gmail.com: > From: Dillon Min <dillon.minfei@gmail.com> > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > with mipi_dpi_interface driver, can support ili9341 with serial > mode or parallel rgb interface mode by register configuration. > > Cc: Linus Walleij <linus.walleij@linaro.org> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > --- > +static const struct of_device_id ili9341_of_match[] = { > + { > + .compatible = "st,sf-tc240t-9370-t", > + .data = &ili9341_stm32f429_disco_data, > + }, > + { > + /* porting from tiny/ili9341.c > + * for original mipi dbi compitable > + */ > + .compatible = "adafruit,yx240qv29", I don't understand this, now there will be 2 drivers that support the same display? AFAICT drm/tiny/ili9341.c is just copied into this driver, is the plan to remove the tiny/ driver? If so I couldn't see this mentioned anywhere. Noralf. > + .data = NULL, > + }, > +}; > +MODULE_DEVICE_TABLE(of, ili9341_of_match);
Hi Noralf Thanks for your time to review my patch. On Thu, 22 Jul 2021 at 01:42, Noralf Trønnes <noralf@tronnes.org> wrote: > > > > Den 21.07.2021 09.41, skrev dillon.minfei@gmail.com: > > From: Dillon Min <dillon.minfei@gmail.com> > > > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > > with mipi_dpi_interface driver, can support ili9341 with serial > > mode or parallel rgb interface mode by register configuration. > > > > Cc: Linus Walleij <linus.walleij@linaro.org> > > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > > --- > > > +static const struct of_device_id ili9341_of_match[] = { > > + { > > + .compatible = "st,sf-tc240t-9370-t", > > + .data = &ili9341_stm32f429_disco_data, > > + }, > > + { > > + /* porting from tiny/ili9341.c > > + * for original mipi dbi compitable > > + */ > > + .compatible = "adafruit,yx240qv29", > > I don't understand this, now there will be 2 drivers that support the > same display? There is no reason to create two drivers to support the same display. To support only-dbi and dbi+dpi panel at drm/panel or drm/tiny both fine with me. > > AFAICT drm/tiny/ili9341.c is just copied into this driver, is the plan > to remove the tiny/ driver? If so I couldn't see this mentioned anywhere. Yes, I'd like to merge the code from drm/tiny/ili9341.c to this driver (to make a single driver to support different bus). I have two purpose to extend the feature drm/tiny/ili9341.c - keep compatible = "adafruit,yx240qv29", add bus mode dts bindings (panel_bus) to define the interface which host wants to use. such as panel_bus="dbi" or "rgb" or "i80" for this case, i will add dpi code to drm/tiny/ili9341.c. - merge tiny/ili9341.c to this driver,remove drm/tiny/ili9341.c, add new dts compatible string to support other interfaces. just like what i'm doing now. I have no idea about your plan on drm/tiny drivers, actually some of these panels under the diny folder can support both dbi and dbi+dpi (much faster, need more pins). no doubt the requirement to support dpi is always there. What is your preference? Thanks & Regards Dillon > > Noralf. > > > + .data = NULL, > > + }, > > +}; > > +MODULE_DEVICE_TABLE(of, ili9341_of_match);
Hi Dillon, On Thu, Jul 22, 2021 at 4:38 AM Dillon Min <dillon.minfei@gmail.com> wrote: > > Hi Jagan > > Thanks for your time to review my code. > > On Wed, 21 Jul 2021 at 23:48, Jagan Teki <jagan@amarulasolutions.com> wrote: > > > > On Wed, Jul 21, 2021 at 1:11 PM <dillon.minfei@gmail.com> wrote: > > > > > > From: Dillon Min <dillon.minfei@gmail.com> > > > > > > This driver combine tiny/ili9341.c mipi_dbi_interface driver > > > with mipi_dpi_interface driver, can support ili9341 with serial > > > mode or parallel rgb interface mode by register configuration. > > > > > > Cc: Linus Walleij <linus.walleij@linaro.org> > > > Signed-off-by: Dillon Min <dillon.minfei@gmail.com> > > > --- > > > changes in v2: > > > - replace vcc regulator to three bulk regulators(vci, vddi, vddi-led) > > > according to linus suggestion, thanks. > > > > > > drivers/gpu/drm/panel/Kconfig | 12 + > > > drivers/gpu/drm/panel/Makefile | 1 + > > > drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 778 +++++++++++++++++++++++++++ > > > 3 files changed, 791 insertions(+) > > > create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > > > > > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig > > > index ef87d92cdf49..eb34b8d1b19a 100644 > > > --- a/drivers/gpu/drm/panel/Kconfig > > > +++ b/drivers/gpu/drm/panel/Kconfig > > > @@ -124,6 +124,18 @@ config DRM_PANEL_ILITEK_IL9322 > > > Say Y here if you want to enable support for Ilitek IL9322 > > > QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. > > > > > > +config DRM_PANEL_ILITEK_ILI9341 > > > + tristate "Ilitek ILI9341 240x320 QVGA panels" > > > + depends on OF && SPI > > > + depends on DRM_KMS_HELPER > > > + depends on DRM_KMS_CMA_HELPER > > > + depends on BACKLIGHT_CLASS_DEVICE > > > + select DRM_MIPI_DBI > > > + help > > > + Say Y here if you want to enable support for Ilitek IL9341 > > > + QVGA (240x320) RGB panels. support serial & parallel rgb > > > + interface. > > > + > > > config DRM_PANEL_ILITEK_ILI9881C > > > tristate "Ilitek ILI9881C-based panels" > > > depends on OF > > > diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile > > > index cae4d976c069..0ecde184665d 100644 > > > --- a/drivers/gpu/drm/panel/Makefile > > > +++ b/drivers/gpu/drm/panel/Makefile > > > @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o > > > obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o > > > obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o > > > obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o > > > +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o > > > obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o > > > obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o > > > obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o > > > diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > > new file mode 100644 > > > index 000000000000..717b0b930e2f > > > --- /dev/null > > > +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c > > > @@ -0,0 +1,778 @@ > > > +// SPDX-License-Identifier: GPL-2.0-only > > > +/* > > > + * Ilitek ILI9341 TFT LCD drm_panel driver. > > > + * > > > + * This panel can be configured to support: > > > + * - 16-bit parallel RGB interface > > > + * - 18-bit parallel RGB interface > > > + * - 4-line serial spi interface > > > + * > > > + * Copyright (C) 2021 Dillon Min <dillon.minfei@gmail.com> > > > + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c > > > + * the reuse of DBI abstraction part referred from Linus's patch > > > + * "drm/panel: s6e63m0: Switch to DBI abstraction for SPI" > > > + */ > > > + > > > +#include <linux/bitops.h> > > > +#include <linux/gpio/consumer.h> > > > +#include <linux/module.h> > > > +#include <linux/of_device.h> > > > +#include <linux/regulator/consumer.h> > > > +#include <linux/spi/spi.h> > > > +#include <linux/delay.h> > > > +#include <video/mipi_display.h> > > > +#include <drm/drm_mipi_dbi.h> > > > +#include <drm/drm_gem_framebuffer_helper.h> > > > +#include <drm/drm_gem_cma_helper.h> > > > +#include <drm/drm_fb_helper.h> > > > +#include <drm/drm_atomic_helper.h> > > > +#include <drm/drm_gem_atomic_helper.h> > > > + > > > +#include <drm/drm_drv.h> > > > +#include <drm/drm_modes.h> > > > +#include <drm/drm_panel.h> > > > +#include <drm/drm_print.h> > > > + > > > +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ > > > +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ > > > +#define ILI9341_DFC 0xb6 /* Display Function Control register */ > > > +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ > > > +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ > > > +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ > > > +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ > > > +#define ILI9341_POWERA 0xcb /* Power control A register */ > > > +#define ILI9341_POWERB 0xcf /* Power control B register */ > > > +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ > > > +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ > > > +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ > > > +#define ILI9341_DTCB 0xea /* Driver timing control B */ > > > +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ > > > +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ > > > +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ > > > +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ > > > +#define ILI9341_ETMOD 0xb7 /* Entry mode set */ > > > + > > > +#define ILI9341_MADCTL_BGR BIT(3) > > > +#define ILI9341_MADCTL_MV BIT(5) > > > +#define ILI9341_MADCTL_MX BIT(6) > > > +#define ILI9341_MADCTL_MY BIT(7) > > > + > > > +#define ILI9341_POWER_B_LEN 3 > > > +#define ILI9341_POWER_SEQ_LEN 4 > > > +#define ILI9341_DTCA_LEN 3 > > > +#define ILI9341_DTCB_LEN 2 > > > +#define ILI9341_POWER_A_LEN 5 > > > +#define ILI9341_DFC_1_LEN 2 > > > +#define ILI9341_FRC_LEN 2 > > > +#define ILI9341_VCOM_1_LEN 2 > > > +#define ILI9341_DFC_2_LEN 4 > > > +#define ILI9341_COLUMN_ADDR_LEN 4 > > > +#define ILI9341_PAGE_ADDR_LEN 4 > > > +#define ILI9341_INTERFACE_LEN 3 > > > +#define ILI9341_PGAMMA_LEN 15 > > > +#define ILI9341_NGAMMA_LEN 15 > > > +#define ILI9341_CA_LEN 3 > > > + > > > +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6) | BIT(4)) > > > +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6) | BIT(5)) > > > +#define ILI9341_GAMMA_CURVE_1 BIT(0) > > > +#define ILI9341_IF_WE_MODE BIT(0) > > > +#define ILI9341_IF_BIG_ENDIAN 0x00 > > > +#define ILI9341_IF_DM_RGB BIT(2) > > > +#define ILI9341_IF_DM_INTERNAL 0x00 > > > +#define ILI9341_IF_DM_VSYNC BIT(3) > > > +#define ILI9341_IF_RM_RGB BIT(1) > > > +#define ILI9341_IF_RIM_RGB 0x00 > > > + > > > +#define ILI9341_COLUMN_ADDR 0x00ef > > > +#define ILI9341_PAGE_ADDR 0x013f > > > + > > > +#define ILI9341_RGB_EPL BIT(0) > > > +#define ILI9341_RGB_DPL BIT(1) > > > +#define ILI9341_RGB_HSPL BIT(2) > > > +#define ILI9341_RGB_VSPL BIT(3) > > > +#define ILI9341_RGB_DE_MODE BIT(6) > > > +#define ILI9341_RGB_DISP_PATH_MEM BIT(7) > > > + > > > +#define ILI9341_DBI_VCOMH_4P6V 0x23 > > > +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 > > > +#define ILI9341_DBI_PRC_NORMAL 0x20 > > > +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e > > > +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 > > > +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 > > > +#define ILI9341_DBI_FRC_DIVA 0x00 > > > +#define ILI9341_DBI_FRC_RTNA 0x1b > > > +#define ILI9341_DBI_EMS_GAS BIT(0) > > > +#define ILI9341_DBI_EMS_DTS BIT(1) > > > +#define ILI9341_DBI_EMS_GON BIT(2) > > > + > > > +/** > > > + * struct ili9341_config - the system specific ILI9341 configuration > > > + * @max_spi_speed: 10000000 > > > + */ > > > +struct ili9341_config { > > > + u32 max_spi_speed; > > > + /** @mode: the drm display mode */ > > > + const struct drm_display_mode mode; > > > + /** @ca: TODO: need comments for this register */ > > > + u8 ca[ILI9341_CA_LEN]; > > > + /** @power_b: TODO: need comments for this register */ > > > + u8 power_b[ILI9341_POWER_B_LEN]; > > > + /** @power_seq: TODO: need comments for this register */ > > > + u8 power_seq[ILI9341_POWER_SEQ_LEN]; > > > + /** @dtca: TODO: need comments for this register */ > > > + u8 dtca[ILI9341_DTCA_LEN]; > > > + /** @dtcb: TODO: need comments for this register */ > > > + u8 dtcb[ILI9341_DTCB_LEN]; > > > + /** @power_a: TODO: need comments for this register */ > > > + u8 power_a[ILI9341_POWER_A_LEN]; > > > + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ > > > + u8 frc[ILI9341_FRC_LEN]; > > > + /** @prc: TODO: need comments for this register */ > > > + u8 prc; > > > + /** @dfc_1: B6h DISCTRL (Display Function Control) */ > > > + u8 dfc_1[ILI9341_DFC_1_LEN]; > > > + /** @power_1: Power Control 1 (C0h) */ > > > + u8 power_1; > > > + /** @power_2: Power Control 2 (C1h) */ > > > + u8 power_2; > > > + /** @vcom_1: VCOM Control 1(C5h) */ > > > + u8 vcom_1[ILI9341_VCOM_1_LEN]; > > > + /** @vcom_2: VCOM Control 2(C7h) */ > > > + u8 vcom_2; > > > + /** @address_mode: Memory Access Control (36h) */ > > > + u8 address_mode; > > > + /** @g3amma_en: TODO: need comments for this register */ > > > + u8 g3amma_en; > > > + /** @rgb_interface: RGB Interface Signal Control (B0h) */ > > > + u8 rgb_interface; > > > + /** @dfc_2: refer to dfc_1 */ > > > + u8 dfc_2[ILI9341_DFC_2_LEN]; > > > + /** @column_addr: Column Address Set (2Ah) */ > > > + u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; > > > + /** @page_addr: Page Address Set (2Bh) */ > > > + u8 page_addr[ILI9341_PAGE_ADDR_LEN]; > > > + /** @interface: Interface Control (F6h) */ > > > + u8 interface[ILI9341_INTERFACE_LEN]; > > > + /** @pixel_format: This command sets the pixel format for the RGB */ > > > + /* image data used by > > > + */ > > > + u8 pixel_format; > > > + /** @gamma_curve: This command is used to select the desired Gamma */ > > > + /* curve for the > > > + */ > > > + u8 gamma_curve; > > > + /** @pgamma: Positive Gamma Correction (E0h) */ > > > + u8 pgamma[ILI9341_PGAMMA_LEN]; > > > + /** @ngamma: Negative Gamma Correction (E1h) */ > > > + u8 ngamma[ILI9341_NGAMMA_LEN]; > > > +}; > > > + > > > +struct ili9341 { > > > + struct device *dev; > > > + const struct ili9341_config *conf; > > > + struct drm_panel panel; > > > + struct gpio_desc *reset_gpio; > > > + struct gpio_desc *dc_gpio; > > > + struct mipi_dbi *dbi; > > > + u32 max_spi_speed; > > > + struct regulator_bulk_data supplies[3]; > > > +}; > > > + > > > +/* > > > + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller > > > + */ > > > +static const struct ili9341_config ili9341_stm32f429_disco_data = { > > > + .max_spi_speed = 10000000, > > > + .mode = { > > > + .clock = 6100, > > > + .hdisplay = 240, > > > + .hsync_start = 240 + 10,/* hfp 10 */ > > > + .hsync_end = 240 + 10 + 10,/* hsync 10 */ > > > + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ > > > + .vdisplay = 320, > > > + .vsync_start = 320 + 4,/* vfp 4 */ > > > + .vsync_end = 320 + 4 + 2,/* vsync 2 */ > > > + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ > > > + .flags = 0, > > > + .width_mm = 65, > > > + .height_mm = 50, > > > + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, > > > + }, > > > + .ca = {0xc3, 0x08, 0x50}, > > > + .power_b = {0x00, 0xc1, 0x30}, > > > + .power_seq = {0x64, 0x03, 0x12, 0x81}, > > > + .dtca = {0x85, 0x00, 0x78}, > > > + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, > > > + .prc = 0x20, > > > + .dtcb = {0x00, 0x00}, > > > + /* 0x00 fosc, 0x1b 70hz */ > > > + .frc = {0x00, 0x1b}, > > > + /* 0x0a Interval scan, AGND AGND AGND AGND > > > + * 0xa2 Normally white, G1 -> G320, S720 -> S1, > > > + * Scan Cycle 5 frames,85ms > > > + */ > > > + .dfc_1 = {0x0a, 0xa2}, > > > + /* 0x10 3.65v */ > > > + .power_1 = 0x10, > > > + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ > > > + .power_2 = 0x10, > > > + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ > > > + .vcom_1 = {0x45, 0x15}, > > > + /* 0x90 offset voltage, VMH-48, VML-48 */ > > > + .vcom_2 = 0x90, > > > + /* 0xc8 Row Address Order, Column Address Order > > > + * BGR 1 > > > + */ > > > + .address_mode = 0xc8, > > > + .g3amma_en = 0x00, > > > + /* 0xc2 > > > + * Display Data Path: Memory > > > + * RGB: DE mode > > > + * DOTCLK polarity set (data fetched at the falling time) > > > + */ > > > + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | > > > + ILI9341_RGB_DE_MODE | > > > + ILI9341_RGB_DPL, > > > + /* > > > + * 0x0a > > > + * Gate outputs in non-display area: Interval scan > > > + * Determine source/VCOM output in a non-display area in the partial > > > + * display mode: AGND AGND AGND AGND > > > + * > > > + * 0xa7 > > > + * Scan Cycle: 15 frames > > > + * fFLM = 60Hz: 255ms > > > + * Liquid crystal type: Normally white > > > + * Gate Output Scan Direction: G1 -> G320 > > > + * Source Output Scan Direction: S720 -> S1 > > > + * > > > + * 0x27 > > > + * LCD Driver Line: 320 lines > > > + * > > > + * 0x04 > > > + * PCDIV: 4 > > > + */ > > > + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, > > > + /* column address: 240 */ > > > + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, > > > + ILI9341_COLUMN_ADDR & 0xff}, > > > + /* page address: 320 */ > > > + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, > > > + ILI9341_PAGE_ADDR & 0xff}, > > > + /* Memory write control: When the transfer number of data exceeds > > > + * (EC-SC+1)*(EP-SP+1), the column and page number will be > > > + * reset, and the exceeding data will be written into the following > > > + * column and page. > > > + * Display Operation Mode: RGB Interface Mode > > > + * Interface for RAM Access: RGB interface > > > + * 16- bit RGB interface (1 transfer/pixel) > > > + */ > > > + .interface = {ILI9341_IF_WE_MODE, 0x00, > > > + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, > > > + /* DPI: 16 bits / pixel */ > > > + .pixel_format = ILI9341_PIXEL_DPI_16_BITS, > > > + /* Curve Selected: Gamma curve 1 (G2.2) */ > > > + .gamma_curve = ILI9341_GAMMA_CURVE_1, > > > + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, > > > + 0x09, 0x4e, 0x78, 0x3c, 0x09, > > > + 0x13, 0x05, 0x17, 0x11, 0x00}, > > > + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, > > > + 0x07, 0x31, 0x33, 0x42, 0x05, > > > + 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, > > > +}; > > > + > > > +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) > > > +{ > > > + return container_of(panel, struct ili9341, panel); > > > +} > > > + > > > +static void ili9341_dpi_init(struct ili9341 *ili) > > > +{ > > > + struct mipi_dbi *dbi = ili->dbi; > > > + struct ili9341_config *cfg = (struct ili9341_config *)ili->conf; > > > + > > > + /* Power Control */ > > > + mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b, > > > + ILI9341_POWER_B_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq, > > > + ILI9341_POWER_SEQ_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca, > > > + ILI9341_DTCA_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a, > > > + ILI9341_POWER_A_LEN); > > > + mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb, > > > + ILI9341_DTCB_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1, > > > + ILI9341_DFC_1_LEN); > > > + mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1); > > > + mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2); > > > + > > > + /* VCOM */ > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1, > > > + ILI9341_VCOM_1_LEN); > > > + mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2); > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode); > > > + > > > + /* Gamma */ > > > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en); > > > + mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2, > > > + ILI9341_DFC_2_LEN); > > > + > > > + /* Colomn address set */ > > > + mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS, > > > + cfg->column_addr, ILI9341_COLUMN_ADDR_LEN); > > > + > > > + /* Page address set */ > > > + mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS, > > > + cfg->page_addr, ILI9341_PAGE_ADDR_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface, > > > + ILI9341_INTERFACE_LEN); > > > + > > > + /* Format */ > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format); > > > + mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); > > > + msleep(200); > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma, > > > + ILI9341_PGAMMA_LEN); > > > + mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma, > > > + ILI9341_NGAMMA_LEN); > > > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); > > > + msleep(200); > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); > > > + mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); > > > + > > > + dev_info(ili->dev, "initialized display rgb interface\n"); > > > +} > > > + > > > +static int ili9341_dpi_power_on(struct ili9341 *ili) > > > +{ > > > + int ret = 0; > > > + > > > + /* Assert RESET */ > > > + gpiod_set_value(ili->reset_gpio, 1); > > > + > > > + /* Enable power */ > > > + ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies), > > > + ili->supplies); > > > + if (ret < 0) { > > > + dev_err(ili->dev, "unable to enable vcc\n"); > > > + return ret; > > > + } > > > + msleep(20); > > > + > > > + /* De-assert RESET */ > > > + gpiod_set_value(ili->reset_gpio, 0); > > > + msleep(20); > > > + > > > + return 0; > > > +} > > > + > > > +static int ili9341_dpi_power_off(struct ili9341 *ili) > > > +{ > > > + /* Assert RESET */ > > > + gpiod_set_value(ili->reset_gpio, 1); > > > + > > > + /* Disable power */ > > > + return regulator_bulk_disable(ARRAY_SIZE(ili->supplies), > > > + ili->supplies); > > > +} > > > + > > > +static int ili9341_dpi_disable(struct drm_panel *panel) > > > +{ > > > + struct ili9341 *ili = panel_to_ili9341(panel); > > > + > > > + mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF); > > > + return 0; > > > +} > > > + > > > +static int ili9341_dpi_unprepare(struct drm_panel *panel) > > > +{ > > > + struct ili9341 *ili = panel_to_ili9341(panel); > > > + > > > + return ili9341_dpi_power_off(ili); > > > +} > > > + > > > +static int ili9341_dpi_prepare(struct drm_panel *panel) > > > +{ > > > + struct ili9341 *ili = panel_to_ili9341(panel); > > > + int ret; > > > + > > > + ret = ili9341_dpi_power_on(ili); > > > + if (ret < 0) > > > + return ret; > > > + > > > + ili9341_dpi_init(ili); > > > + > > > + return ret; > > > +} > > > + > > > +static int ili9341_dpi_enable(struct drm_panel *panel) > > > +{ > > > + struct ili9341 *ili = panel_to_ili9341(panel); > > > + > > > + mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON); > > > + return 0; > > > +} > > > + > > > +static int ili9341_dpi_get_modes(struct drm_panel *panel, > > > + struct drm_connector *connector) > > > +{ > > > + struct ili9341 *ili = panel_to_ili9341(panel); > > > + struct drm_device *drm = connector->dev; > > > + struct drm_display_mode *mode; > > > + struct drm_display_info *info; > > > + > > > + info = &connector->display_info; > > > + info->width_mm = ili->conf->mode.width_mm; > > > + info->height_mm = ili->conf->mode.height_mm; > > > + > > > + if (ili->conf->rgb_interface & ILI9341_RGB_DPL) > > > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; > > > + else > > > + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; > > > + > > > + if (ili->conf->rgb_interface & ILI9341_RGB_EPL) > > > + info->bus_flags |= DRM_BUS_FLAG_DE_LOW; > > > + else > > > + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; > > > + > > > + mode = drm_mode_duplicate(drm, &ili->conf->mode); > > > + if (!mode) { > > > + DRM_ERROR("bad mode or failed to add mode\n"); > > > + return -EINVAL; > > > + } > > > + drm_mode_set_name(mode); > > > + > > > + /* Set up the polarity */ > > > + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) > > > + mode->flags |= DRM_MODE_FLAG_PHSYNC; > > > + else > > > + mode->flags |= DRM_MODE_FLAG_NHSYNC; > > > + > > > + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) > > > + mode->flags |= DRM_MODE_FLAG_PVSYNC; > > > + else > > > + mode->flags |= DRM_MODE_FLAG_NVSYNC; > > > + > > > + drm_mode_probed_add(connector, mode); > > > + > > > + return 1; /* Number of modes */ > > > +} > > > + > > > +static const struct drm_panel_funcs ili9341_dpi_funcs = { > > > + .disable = ili9341_dpi_disable, > > > + .unprepare = ili9341_dpi_unprepare, > > > + .prepare = ili9341_dpi_prepare, > > > + .enable = ili9341_dpi_enable, > > > + .get_modes = ili9341_dpi_get_modes, > > > +}; > > > + > > > +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, > > > + struct drm_crtc_state *crtc_state, > > > + struct drm_plane_state *plane_state) > > > +{ > > > + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); > > > + struct mipi_dbi *dbi = &dbidev->dbi; > > > + u8 addr_mode; > > > + int ret, idx; > > > + > > > + if (!drm_dev_enter(pipe->crtc.dev, &idx)) > > > + return; > > > + > > > + DRM_DEBUG_KMS("\n"); > > > + > > > + ret = mipi_dbi_poweron_conditional_reset(dbidev); > > > + if (ret < 0) > > > + goto out_exit; > > > + if (ret == 1) > > > + goto out_enable; > > > + > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); > > > + > > > + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); > > > + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); > > > + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); > > > + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); > > > + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); > > > + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); > > > + > > > + /* Power Control */ > > > + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); > > > + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); > > > + /* VCOM */ > > > + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, > > > + ILI9341_DBI_VCOM_1_VML_1P5V); > > > + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); > > > + > > > + /* Memory Access Control */ > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, > > > + MIPI_DCS_PIXEL_FMT_16BIT); > > > + > > > + /* Frame Rate */ > > > + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, > > > + ILI9341_DBI_FRC_RTNA & 0x1f); > > > + > > > + /* Gamma */ > > > + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); > > > + mipi_dbi_command(dbi, ILI9341_PGAMMA, > > > + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, > > > + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); > > > + mipi_dbi_command(dbi, ILI9341_NGAMMA, > > > + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, > > > + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); > > > + > > > + /* DDRAM */ > > > + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | > > > + ILI9341_DBI_EMS_DTS | > > > + ILI9341_DBI_EMS_GON); > > > + > > > + /* Display */ > > > + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); > > > + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); > > > + msleep(100); > > > + > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); > > > + msleep(100); > > > + > > > +out_enable: > > > + switch (dbidev->rotation) { > > > + default: > > > + addr_mode = ILI9341_MADCTL_MX; > > > + break; > > > + case 90: > > > + addr_mode = ILI9341_MADCTL_MV; > > > + break; > > > + case 180: > > > + addr_mode = ILI9341_MADCTL_MY; > > > + break; > > > + case 270: > > > + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | > > > + ILI9341_MADCTL_MX; > > > + break; > > > + } > > > + addr_mode |= ILI9341_MADCTL_BGR; > > > + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); > > > + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); > > > + DRM_DEBUG_KMS("initialized display serial interface\n"); > > > +out_exit: > > > + drm_dev_exit(idx); > > > +} > > > + > > > +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { > > > + .enable = ili9341_dbi_enable, > > > + .disable = mipi_dbi_pipe_disable, > > > + .update = mipi_dbi_pipe_update, > > > + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb, > > > +}; > > > + > > > +static const struct drm_display_mode ili9341_dbi_mode = { > > > + DRM_SIMPLE_MODE(240, 320, 37, 49), > > > +}; > > > + > > > +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops); > > > + > > > +static struct drm_driver ili9341_dbi_driver = { > > > + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, > > > + .fops = &ili9341_dbi_fops, > > > + DRM_GEM_CMA_DRIVER_OPS_VMAP, > > > + .debugfs_init = mipi_dbi_debugfs_init, > > > + .name = "ili9341", > > > + .desc = "Ilitek ILI9341", > > > + .date = "20210716", > > > + .major = 1, > > > + .minor = 0, > > > +}; > > > + > > > +static int _ili9341_probe(struct spi_device *spi, bool dpi) > > > +{ > > > + struct gpio_desc *dc; > > > + struct gpio_desc *reset; > > > + struct device *dev = &spi->dev; > > > + int ret; > > > + > > > + reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); > > > + if (IS_ERR(reset)) > > > + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); > > > + > > > + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); > > > + if (IS_ERR(dc)) > > > + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); > > > > Small nit. Moving the above dts parse code into the main probe and > > have functions for dpi and !dpi would make code more readable. > > Okay, just to make sure I fully understand your suggestion, > you ask me to change the code below, right? thanks. > > static int ili9341_dpi_probe(struct spi_device *spi, > struct gpio_desc *dc, > struct gpio_desc *reset) > { > .... > } > > static int ili9341_dbi_probe(struct spi_device *spi, > struct gpio_desc *dc, > struct gpio_desc *reset){ > .... > } > > static int ili9341_probe(struct spi_device *spi) > { > .... > struct device *dev = &spi->dev; > struct gpio_desc *dc; > struct gpio_desc *reset; > const struct spi_device_id *id = spi_get_device_id(spi); > > reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); > if (IS_ERR(reset)) > drm_err(dev, "Failed to get gpio 'reset'\n"); > > dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); > if (IS_ERR(dc)) > drm_err(dev, "Failed to get gpio 'dc'\n"); > > if (!strcmp(id->name, "sf-tc240t-9370-t")) > return ili9341_dpi_probe(spi, dc, reset); > else if (!strcmp(id->name, "yx240qv29")) > return ili9341_dbi_probe(spi, dc, reset); > > return -1; > } Perfect, thanks! Jagan.
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index ef87d92cdf49..eb34b8d1b19a 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -124,6 +124,18 @@ config DRM_PANEL_ILITEK_IL9322 Say Y here if you want to enable support for Ilitek IL9322 QVGA (320x240) RGB, YUV and ITU-T BT.656 panels. +config DRM_PANEL_ILITEK_ILI9341 + tristate "Ilitek ILI9341 240x320 QVGA panels" + depends on OF && SPI + depends on DRM_KMS_HELPER + depends on DRM_KMS_CMA_HELPER + depends on BACKLIGHT_CLASS_DEVICE + select DRM_MIPI_DBI + help + Say Y here if you want to enable support for Ilitek IL9341 + QVGA (240x320) RGB panels. support serial & parallel rgb + interface. + config DRM_PANEL_ILITEK_ILI9881C tristate "Ilitek ILI9881C-based panels" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index cae4d976c069..0ecde184665d 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c new file mode 100644 index 000000000000..717b0b930e2f --- /dev/null +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c @@ -0,0 +1,778 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Ilitek ILI9341 TFT LCD drm_panel driver. + * + * This panel can be configured to support: + * - 16-bit parallel RGB interface + * - 18-bit parallel RGB interface + * - 4-line serial spi interface + * + * Copyright (C) 2021 Dillon Min <dillon.minfei@gmail.com> + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c + * the reuse of DBI abstraction part referred from Linus's patch + * "drm/panel: s6e63m0: Switch to DBI abstraction for SPI" + */ + +#include <linux/bitops.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> +#include <linux/delay.h> +#include <video/mipi_display.h> +#include <drm/drm_mipi_dbi.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_fb_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_gem_atomic_helper.h> + +#include <drm/drm_drv.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h> + +#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ +#define ILI9341_DFC 0xb6 /* Display Function Control register */ +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ +#define ILI9341_POWERA 0xcb /* Power control A register */ +#define ILI9341_POWERB 0xcf /* Power control B register */ +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ +#define ILI9341_DTCB 0xea /* Driver timing control B */ +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ +#define ILI9341_ETMOD 0xb7 /* Entry mode set */ + +#define ILI9341_MADCTL_BGR BIT(3) +#define ILI9341_MADCTL_MV BIT(5) +#define ILI9341_MADCTL_MX BIT(6) +#define ILI9341_MADCTL_MY BIT(7) + +#define ILI9341_POWER_B_LEN 3 +#define ILI9341_POWER_SEQ_LEN 4 +#define ILI9341_DTCA_LEN 3 +#define ILI9341_DTCB_LEN 2 +#define ILI9341_POWER_A_LEN 5 +#define ILI9341_DFC_1_LEN 2 +#define ILI9341_FRC_LEN 2 +#define ILI9341_VCOM_1_LEN 2 +#define ILI9341_DFC_2_LEN 4 +#define ILI9341_COLUMN_ADDR_LEN 4 +#define ILI9341_PAGE_ADDR_LEN 4 +#define ILI9341_INTERFACE_LEN 3 +#define ILI9341_PGAMMA_LEN 15 +#define ILI9341_NGAMMA_LEN 15 +#define ILI9341_CA_LEN 3 + +#define ILI9341_PIXEL_DPI_16_BITS (BIT(6) | BIT(4)) +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6) | BIT(5)) +#define ILI9341_GAMMA_CURVE_1 BIT(0) +#define ILI9341_IF_WE_MODE BIT(0) +#define ILI9341_IF_BIG_ENDIAN 0x00 +#define ILI9341_IF_DM_RGB BIT(2) +#define ILI9341_IF_DM_INTERNAL 0x00 +#define ILI9341_IF_DM_VSYNC BIT(3) +#define ILI9341_IF_RM_RGB BIT(1) +#define ILI9341_IF_RIM_RGB 0x00 + +#define ILI9341_COLUMN_ADDR 0x00ef +#define ILI9341_PAGE_ADDR 0x013f + +#define ILI9341_RGB_EPL BIT(0) +#define ILI9341_RGB_DPL BIT(1) +#define ILI9341_RGB_HSPL BIT(2) +#define ILI9341_RGB_VSPL BIT(3) +#define ILI9341_RGB_DE_MODE BIT(6) +#define ILI9341_RGB_DISP_PATH_MEM BIT(7) + +#define ILI9341_DBI_VCOMH_4P6V 0x23 +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 +#define ILI9341_DBI_PRC_NORMAL 0x20 +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 +#define ILI9341_DBI_FRC_DIVA 0x00 +#define ILI9341_DBI_FRC_RTNA 0x1b +#define ILI9341_DBI_EMS_GAS BIT(0) +#define ILI9341_DBI_EMS_DTS BIT(1) +#define ILI9341_DBI_EMS_GON BIT(2) + +/** + * struct ili9341_config - the system specific ILI9341 configuration + * @max_spi_speed: 10000000 + */ +struct ili9341_config { + u32 max_spi_speed; + /** @mode: the drm display mode */ + const struct drm_display_mode mode; + /** @ca: TODO: need comments for this register */ + u8 ca[ILI9341_CA_LEN]; + /** @power_b: TODO: need comments for this register */ + u8 power_b[ILI9341_POWER_B_LEN]; + /** @power_seq: TODO: need comments for this register */ + u8 power_seq[ILI9341_POWER_SEQ_LEN]; + /** @dtca: TODO: need comments for this register */ + u8 dtca[ILI9341_DTCA_LEN]; + /** @dtcb: TODO: need comments for this register */ + u8 dtcb[ILI9341_DTCB_LEN]; + /** @power_a: TODO: need comments for this register */ + u8 power_a[ILI9341_POWER_A_LEN]; + /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ + u8 frc[ILI9341_FRC_LEN]; + /** @prc: TODO: need comments for this register */ + u8 prc; + /** @dfc_1: B6h DISCTRL (Display Function Control) */ + u8 dfc_1[ILI9341_DFC_1_LEN]; + /** @power_1: Power Control 1 (C0h) */ + u8 power_1; + /** @power_2: Power Control 2 (C1h) */ + u8 power_2; + /** @vcom_1: VCOM Control 1(C5h) */ + u8 vcom_1[ILI9341_VCOM_1_LEN]; + /** @vcom_2: VCOM Control 2(C7h) */ + u8 vcom_2; + /** @address_mode: Memory Access Control (36h) */ + u8 address_mode; + /** @g3amma_en: TODO: need comments for this register */ + u8 g3amma_en; + /** @rgb_interface: RGB Interface Signal Control (B0h) */ + u8 rgb_interface; + /** @dfc_2: refer to dfc_1 */ + u8 dfc_2[ILI9341_DFC_2_LEN]; + /** @column_addr: Column Address Set (2Ah) */ + u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; + /** @page_addr: Page Address Set (2Bh) */ + u8 page_addr[ILI9341_PAGE_ADDR_LEN]; + /** @interface: Interface Control (F6h) */ + u8 interface[ILI9341_INTERFACE_LEN]; + /** @pixel_format: This command sets the pixel format for the RGB */ + /* image data used by + */ + u8 pixel_format; + /** @gamma_curve: This command is used to select the desired Gamma */ + /* curve for the + */ + u8 gamma_curve; + /** @pgamma: Positive Gamma Correction (E0h) */ + u8 pgamma[ILI9341_PGAMMA_LEN]; + /** @ngamma: Negative Gamma Correction (E1h) */ + u8 ngamma[ILI9341_NGAMMA_LEN]; +}; + +struct ili9341 { + struct device *dev; + const struct ili9341_config *conf; + struct drm_panel panel; + struct gpio_desc *reset_gpio; + struct gpio_desc *dc_gpio; + struct mipi_dbi *dbi; + u32 max_spi_speed; + struct regulator_bulk_data supplies[3]; +}; + +/* + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller + */ +static const struct ili9341_config ili9341_stm32f429_disco_data = { + .max_spi_speed = 10000000, + .mode = { + .clock = 6100, + .hdisplay = 240, + .hsync_start = 240 + 10,/* hfp 10 */ + .hsync_end = 240 + 10 + 10,/* hsync 10 */ + .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ + .vdisplay = 320, + .vsync_start = 320 + 4,/* vfp 4 */ + .vsync_end = 320 + 4 + 2,/* vsync 2 */ + .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ + .flags = 0, + .width_mm = 65, + .height_mm = 50, + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, + }, + .ca = {0xc3, 0x08, 0x50}, + .power_b = {0x00, 0xc1, 0x30}, + .power_seq = {0x64, 0x03, 0x12, 0x81}, + .dtca = {0x85, 0x00, 0x78}, + .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, + .prc = 0x20, + .dtcb = {0x00, 0x00}, + /* 0x00 fosc, 0x1b 70hz */ + .frc = {0x00, 0x1b}, + /* 0x0a Interval scan, AGND AGND AGND AGND + * 0xa2 Normally white, G1 -> G320, S720 -> S1, + * Scan Cycle 5 frames,85ms + */ + .dfc_1 = {0x0a, 0xa2}, + /* 0x10 3.65v */ + .power_1 = 0x10, + /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ + .power_2 = 0x10, + /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ + .vcom_1 = {0x45, 0x15}, + /* 0x90 offset voltage, VMH-48, VML-48 */ + .vcom_2 = 0x90, + /* 0xc8 Row Address Order, Column Address Order + * BGR 1 + */ + .address_mode = 0xc8, + .g3amma_en = 0x00, + /* 0xc2 + * Display Data Path: Memory + * RGB: DE mode + * DOTCLK polarity set (data fetched at the falling time) + */ + .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | + ILI9341_RGB_DE_MODE | + ILI9341_RGB_DPL, + /* + * 0x0a + * Gate outputs in non-display area: Interval scan + * Determine source/VCOM output in a non-display area in the partial + * display mode: AGND AGND AGND AGND + * + * 0xa7 + * Scan Cycle: 15 frames + * fFLM = 60Hz: 255ms + * Liquid crystal type: Normally white + * Gate Output Scan Direction: G1 -> G320 + * Source Output Scan Direction: S720 -> S1 + * + * 0x27 + * LCD Driver Line: 320 lines + * + * 0x04 + * PCDIV: 4 + */ + .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, + /* column address: 240 */ + .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, + ILI9341_COLUMN_ADDR & 0xff}, + /* page address: 320 */ + .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, + ILI9341_PAGE_ADDR & 0xff}, + /* Memory write control: When the transfer number of data exceeds + * (EC-SC+1)*(EP-SP+1), the column and page number will be + * reset, and the exceeding data will be written into the following + * column and page. + * Display Operation Mode: RGB Interface Mode + * Interface for RAM Access: RGB interface + * 16- bit RGB interface (1 transfer/pixel) + */ + .interface = {ILI9341_IF_WE_MODE, 0x00, + ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, + /* DPI: 16 bits / pixel */ + .pixel_format = ILI9341_PIXEL_DPI_16_BITS, + /* Curve Selected: Gamma curve 1 (G2.2) */ + .gamma_curve = ILI9341_GAMMA_CURVE_1, + .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, + 0x09, 0x4e, 0x78, 0x3c, 0x09, + 0x13, 0x05, 0x17, 0x11, 0x00}, + .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, + 0x07, 0x31, 0x33, 0x42, 0x05, + 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, +}; + +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) +{ + return container_of(panel, struct ili9341, panel); +} + +static void ili9341_dpi_init(struct ili9341 *ili) +{ + struct mipi_dbi *dbi = ili->dbi; + struct ili9341_config *cfg = (struct ili9341_config *)ili->conf; + + /* Power Control */ + mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b, + ILI9341_POWER_B_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq, + ILI9341_POWER_SEQ_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca, + ILI9341_DTCA_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a, + ILI9341_POWER_A_LEN); + mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc); + mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb, + ILI9341_DTCB_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1, + ILI9341_DFC_1_LEN); + mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1); + mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2); + + /* VCOM */ + mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1, + ILI9341_VCOM_1_LEN); + mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2); + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode); + + /* Gamma */ + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en); + mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface); + mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2, + ILI9341_DFC_2_LEN); + + /* Colomn address set */ + mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS, + cfg->column_addr, ILI9341_COLUMN_ADDR_LEN); + + /* Page address set */ + mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS, + cfg->page_addr, ILI9341_PAGE_ADDR_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface, + ILI9341_INTERFACE_LEN); + + /* Format */ + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format); + mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); + msleep(200); + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve); + mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma, + ILI9341_PGAMMA_LEN); + mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma, + ILI9341_NGAMMA_LEN); + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); + msleep(200); + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); + mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); + + dev_info(ili->dev, "initialized display rgb interface\n"); +} + +static int ili9341_dpi_power_on(struct ili9341 *ili) +{ + int ret = 0; + + /* Assert RESET */ + gpiod_set_value(ili->reset_gpio, 1); + + /* Enable power */ + ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies), + ili->supplies); + if (ret < 0) { + dev_err(ili->dev, "unable to enable vcc\n"); + return ret; + } + msleep(20); + + /* De-assert RESET */ + gpiod_set_value(ili->reset_gpio, 0); + msleep(20); + + return 0; +} + +static int ili9341_dpi_power_off(struct ili9341 *ili) +{ + /* Assert RESET */ + gpiod_set_value(ili->reset_gpio, 1); + + /* Disable power */ + return regulator_bulk_disable(ARRAY_SIZE(ili->supplies), + ili->supplies); +} + +static int ili9341_dpi_disable(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + + mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF); + return 0; +} + +static int ili9341_dpi_unprepare(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + + return ili9341_dpi_power_off(ili); +} + +static int ili9341_dpi_prepare(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + int ret; + + ret = ili9341_dpi_power_on(ili); + if (ret < 0) + return ret; + + ili9341_dpi_init(ili); + + return ret; +} + +static int ili9341_dpi_enable(struct drm_panel *panel) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + + mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON); + return 0; +} + +static int ili9341_dpi_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct ili9341 *ili = panel_to_ili9341(panel); + struct drm_device *drm = connector->dev; + struct drm_display_mode *mode; + struct drm_display_info *info; + + info = &connector->display_info; + info->width_mm = ili->conf->mode.width_mm; + info->height_mm = ili->conf->mode.height_mm; + + if (ili->conf->rgb_interface & ILI9341_RGB_DPL) + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; + else + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; + + if (ili->conf->rgb_interface & ILI9341_RGB_EPL) + info->bus_flags |= DRM_BUS_FLAG_DE_LOW; + else + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; + + mode = drm_mode_duplicate(drm, &ili->conf->mode); + if (!mode) { + DRM_ERROR("bad mode or failed to add mode\n"); + return -EINVAL; + } + drm_mode_set_name(mode); + + /* Set up the polarity */ + if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) + mode->flags |= DRM_MODE_FLAG_PHSYNC; + else + mode->flags |= DRM_MODE_FLAG_NHSYNC; + + if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) + mode->flags |= DRM_MODE_FLAG_PVSYNC; + else + mode->flags |= DRM_MODE_FLAG_NVSYNC; + + drm_mode_probed_add(connector, mode); + + return 1; /* Number of modes */ +} + +static const struct drm_panel_funcs ili9341_dpi_funcs = { + .disable = ili9341_dpi_disable, + .unprepare = ili9341_dpi_unprepare, + .prepare = ili9341_dpi_prepare, + .enable = ili9341_dpi_enable, + .get_modes = ili9341_dpi_get_modes, +}; + +static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, + struct drm_crtc_state *crtc_state, + struct drm_plane_state *plane_state) +{ + struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); + struct mipi_dbi *dbi = &dbidev->dbi; + u8 addr_mode; + int ret, idx; + + if (!drm_dev_enter(pipe->crtc.dev, &idx)) + return; + + DRM_DEBUG_KMS("\n"); + + ret = mipi_dbi_poweron_conditional_reset(dbidev); + if (ret < 0) + goto out_exit; + if (ret == 1) + goto out_enable; + + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); + + mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); + mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); + mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); + mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); + mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); + mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); + + /* Power Control */ + mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); + mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); + /* VCOM */ + mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, + ILI9341_DBI_VCOM_1_VML_1P5V); + mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); + + /* Memory Access Control */ + mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, + MIPI_DCS_PIXEL_FMT_16BIT); + + /* Frame Rate */ + mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, + ILI9341_DBI_FRC_RTNA & 0x1f); + + /* Gamma */ + mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); + mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); + mipi_dbi_command(dbi, ILI9341_PGAMMA, + 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, + 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); + mipi_dbi_command(dbi, ILI9341_NGAMMA, + 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, + 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); + + /* DDRAM */ + mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | + ILI9341_DBI_EMS_DTS | + ILI9341_DBI_EMS_GON); + + /* Display */ + mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); + mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); + msleep(100); + + mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); + msleep(100); + +out_enable: + switch (dbidev->rotation) { + default: + addr_mode = ILI9341_MADCTL_MX; + break; + case 90: + addr_mode = ILI9341_MADCTL_MV; + break; + case 180: + addr_mode = ILI9341_MADCTL_MY; + break; + case 270: + addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | + ILI9341_MADCTL_MX; + break; + } + addr_mode |= ILI9341_MADCTL_BGR; + mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); + mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); + DRM_DEBUG_KMS("initialized display serial interface\n"); +out_exit: + drm_dev_exit(idx); +} + +static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { + .enable = ili9341_dbi_enable, + .disable = mipi_dbi_pipe_disable, + .update = mipi_dbi_pipe_update, + .prepare_fb = drm_gem_simple_display_pipe_prepare_fb, +}; + +static const struct drm_display_mode ili9341_dbi_mode = { + DRM_SIMPLE_MODE(240, 320, 37, 49), +}; + +DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops); + +static struct drm_driver ili9341_dbi_driver = { + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, + .fops = &ili9341_dbi_fops, + DRM_GEM_CMA_DRIVER_OPS_VMAP, + .debugfs_init = mipi_dbi_debugfs_init, + .name = "ili9341", + .desc = "Ilitek ILI9341", + .date = "20210716", + .major = 1, + .minor = 0, +}; + +static int _ili9341_probe(struct spi_device *spi, bool dpi) +{ + struct gpio_desc *dc; + struct gpio_desc *reset; + struct device *dev = &spi->dev; + int ret; + + reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(reset)) + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); + + dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); + if (IS_ERR(dc)) + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); + + if (!dpi) { + struct mipi_dbi_dev *dbidev; + struct mipi_dbi *dbi; + struct drm_device *drm; + struct regulator *vcc; + u32 rotation = 0; + + vcc = devm_regulator_get_optional(dev, "vcc"); + if (IS_ERR(vcc)) + DRM_DEV_ERROR(dev, "get optional vcc failed\n"); + + dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver, + struct mipi_dbi_dev, drm); + if (IS_ERR(dbidev)) + return PTR_ERR(dbidev); + + dbi = &dbidev->dbi; + drm = &dbidev->drm; + dbi->reset = reset; + dbidev->regulator = vcc; + + drm_mode_config_init(drm); + dbidev->backlight = devm_of_find_backlight(dev); + if (IS_ERR(dbidev->backlight)) + return PTR_ERR(dbidev->backlight); + + device_property_read_u32(dev, "rotation", &rotation); + + ret = mipi_dbi_spi_init(spi, dbi, dc); + if (ret) + return ret; + + ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs, + &ili9341_dbi_mode, rotation); + if (ret) + return ret; + + drm_mode_config_reset(drm); + + ret = drm_dev_register(drm, 0); + if (ret) + return ret; + + spi_set_drvdata(spi, drm); + + drm_fbdev_generic_setup(drm, 0); + } else { + struct ili9341 *ili; + + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL); + if (!ili) + return -ENOMEM; + + ili->dbi = devm_kzalloc(dev, sizeof(struct mipi_dbi), + GFP_KERNEL); + if (!ili->dbi) + return -ENOMEM; + + ili->supplies[0].supply = "vci"; + ili->supplies[1].supply = "vddi"; + ili->supplies[2].supply = "vddi-led"; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ili->supplies), + ili->supplies); + if (ret < 0) { + dev_err(dev, "failed to get regulators: %d\n", ret); + return ret; + } + + ret = mipi_dbi_spi_init(spi, ili->dbi, dc); + if (ret) + return ret; + + spi_set_drvdata(spi, ili); + + ili->dev = dev; + ili->reset_gpio = reset; + /* + * Every new incarnation of this display must have a unique + * data entry for the system in this driver. + */ + ili->conf = of_device_get_match_data(dev); + if (!ili->conf) { + dev_err(dev, "missing device configuration\n"); + return -ENODEV; + } + + ili->max_spi_speed = ili->conf->max_spi_speed; + + drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs, + DRM_MODE_CONNECTOR_DPI); + + drm_panel_add(&ili->panel); + } + + return 0; +} + +static int ili9341_probe(struct spi_device *spi) +{ + const struct spi_device_id *id = spi_get_device_id(spi); + + if (!strcmp(id->name, "sf-tc240t-9370-t")) + return _ili9341_probe(spi, true); + else if (!strcmp(id->name, "yx240qv29")) + return _ili9341_probe(spi, false); + + return -1; +} + +static int ili9341_remove(struct spi_device *spi) +{ + const struct spi_device_id *id = spi_get_device_id(spi); + struct ili9341 *ili = spi_get_drvdata(spi); + struct drm_device *drm = spi_get_drvdata(spi); + + if (!strcmp(id->name, "sf-tc240t-9370-t")) { + ili9341_dpi_power_off(ili); + drm_panel_remove(&ili->panel); + } else if (!strcmp(id->name, "yx240qv29")) { + drm_dev_unplug(drm); + drm_atomic_helper_shutdown(drm); + } + return 0; +} + +static void ili9341_shutdown(struct spi_device *spi) +{ + const struct spi_device_id *id = spi_get_device_id(spi); + + if (!strcmp(id->name, "yx240qv29")) + drm_atomic_helper_shutdown(spi_get_drvdata(spi)); +} + +static const struct of_device_id ili9341_of_match[] = { + { + .compatible = "st,sf-tc240t-9370-t", + .data = &ili9341_stm32f429_disco_data, + }, + { + /* porting from tiny/ili9341.c + * for original mipi dbi compitable + */ + .compatible = "adafruit,yx240qv29", + .data = NULL, + }, +}; +MODULE_DEVICE_TABLE(of, ili9341_of_match); + +static const struct spi_device_id ili9341_id[] = { + { "yx240qv29", 0 }, + { "sf-tc240t-9370-t", 0 }, + { } +}; +MODULE_DEVICE_TABLE(spi, ili9341_id); + +static struct spi_driver ili9341_driver = { + .probe = ili9341_probe, + .remove = ili9341_remove, + .shutdown = ili9341_shutdown, + .id_table = ili9341_id, + .driver = { + .name = "panel-ilitek-ili9341", + .of_match_table = ili9341_of_match, + }, +}; +module_spi_driver(ili9341_driver); + +MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>"); +MODULE_DESCRIPTION("ILI9341 LCD panel driver"); +MODULE_LICENSE("GPL v2");