| Message ID | 20210722042450.11862-6-matt@traverse.com.au |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add Traverse Technologies Ten64 board DTS | expand |
On Thu, Jul 22, 2021 at 04:24:50AM +0000, Mathew McBride wrote: > The Traverse Technologies Ten64 is a Mini-ITX form factor > networking board using the NXP LS1088A SoC. > > This device tree only describes features which the mainline > kernel currently has support for, such as some I2C-connected > devices that are not described at present. > > System documentation may be found at ten64doc.traverse.com.au > > Signed-off-by: Mathew McBride <matt@traverse.com.au> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> # for the MAC/PHY
On Thu, Jul 22, 2021 at 04:24:50AM +0000, Mathew McBride wrote: > The Traverse Technologies Ten64 is a Mini-ITX form factor > networking board using the NXP LS1088A SoC. > > This device tree only describes features which the mainline > kernel currently has support for, such as some I2C-connected > devices that are not described at present. > > System documentation may be found at ten64doc.traverse.com.au > > Signed-off-by: Mathew McBride <matt@traverse.com.au> > --- > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../boot/dts/freescale/fsl-ls1088a-ten64.dts | 375 ++++++++++++++++++ > 2 files changed, 376 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index 25806c4924cb..2b3ee42e4a2a 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts > new file mode 100644 > index 000000000000..7f1584f378fe > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts > @@ -0,0 +1,375 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Device Tree file for Travese Ten64 (LS1088) board > + * Based on fsl-ls1088a-rdb.dts > + * Copyright 2017-2020 NXP > + * Copyright 2019-2021 Traverse Technologies > + * > + * Author: Mathew McBride <matt@traverse.com.au> > + */ > + > +/dts-v1/; > + > +#include "fsl-ls1088a.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "Traverse Ten64"; > + compatible = "traverse,ten64", "fsl,ls1088a"; > + > + aliases { > + serial0 = &duart0; > + serial1 = &duart1; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + buttons { > + compatible = "gpio-keys"; Have a newline between property list and child node. > + /* Fired by system controller when > + * external power off (e.g ATX Power Button) > + * asserted > + */ > + powerdn { > + label = "External Power Down"; > + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; > + interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>; > + linux,code = <KEY_POWER>; > + }; > + > + /* Rear Panel 'ADMIN' button (GPIO_H) */ > + admin { > + label = "ADMIN button"; > + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>; > + interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>; > + linux,code = <KEY_WPS_BUTTON>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + sfp1down { > + label = "ten64:green:sfp1:down"; > + gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>; > + }; > + > + sfp2up { > + label = "ten64:green:sfp2:up"; > + gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>; > + }; > + > + admin { > + label = "ten64:admin"; > + gpios = <&sfpgpio 12 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + sfp_xg0: dpmac2_sfp { We generally use '-' instead of '_' in node name. sfp-dpmac2 might be better. > + compatible = "sff,sfp"; > + i2c-bus = <&sfplower_i2c>; > + tx-fault-gpios = <&sfpgpio 0 GPIO_ACTIVE_HIGH>; > + tx-disable-gpios = <&sfpgpio 1 GPIO_ACTIVE_HIGH>; > + mod-def0-gpios = <&sfpgpio 2 GPIO_ACTIVE_LOW>; > + los-gpios = <&sfpgpio 3 GPIO_ACTIVE_HIGH>; > + maximum-power-milliwatt = <2000>; > + }; > + > + sfp_xg1: dpmac1_sfp { > + compatible = "sff,sfp"; > + i2c-bus = <&sfpupper_i2c>; > + tx-fault-gpios = <&sfpgpio 4 GPIO_ACTIVE_HIGH>; > + tx-disable-gpios = <&sfpgpio 5 GPIO_ACTIVE_HIGH>; > + mod-def0-gpios = <&sfpgpio 6 GPIO_ACTIVE_LOW>; > + los-gpios = <&sfpgpio 7 GPIO_ACTIVE_HIGH>; > + maximum-power-milliwatt = <2000>; > + }; > + > +}; > + > +/* XG1 - Upper SFP */ > +&dpmac1 { > + sfp = <&sfp_xg1>; > + pcs-handle = <&pcs1>; > + phy-connection-type = "10gbase-r"; > + managed = "in-band-status"; > +}; > + > +/* XG0 - Lower SFP */ > +&dpmac2 { > + sfp = <&sfp_xg0>; > + pcs-handle = <&pcs2>; > + phy-connection-type = "10gbase-r"; > + managed = "in-band-status"; > +}; > + > +/* DPMAC3..6 is GE4 to GE8 */ > +&dpmac3 { > + phy-handle = <&mdio1_phy5>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs3_0>; > +}; > + > +&dpmac4 { > + phy-handle = <&mdio1_phy6>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs3_1>; > +}; > + > +&dpmac5 { > + phy-handle = <&mdio1_phy7>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs3_2>; > +}; > + > +&dpmac6 { > + phy-handle = <&mdio1_phy8>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs3_3>; > +}; > + > +/* DPMAC7..10 is GE0 to GE3 */ > +&dpmac7 { > + phy-handle = <&mdio1_phy1>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs7_0>; > +}; > + > +&dpmac8 { > + phy-handle = <&mdio1_phy2>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs7_1>; > +}; > + > +&dpmac9 { > + phy-handle = <&mdio1_phy3>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs7_2>; > +}; > + > +&dpmac10 { > + phy-handle = <&mdio1_phy4>; > + phy-connection-type = "qsgmii"; > + managed = "in-band-status"; > + pcs-handle = <&pcs7_3>; > +}; > + > +&emdio1 { > + status = "okay"; > + > + mdio1_phy5: ethernet-phy@c { > + reg = <0xc>; > + }; > + > + mdio1_phy6: ethernet-phy@d { > + reg = <0xd>; > + }; > + > + mdio1_phy7: ethernet-phy@e { > + reg = <0xe>; > + }; > + > + mdio1_phy8: ethernet-phy@f { > + reg = <0xf>; > + }; > + > + mdio1_phy1: ethernet-phy@1c { > + reg = <0x1c>; > + }; > + > + mdio1_phy2: ethernet-phy@1d { > + reg = <0x1d>; > + }; > + > + mdio1_phy3: ethernet-phy@1e { > + reg = <0x1e>; > + }; > + > + mdio1_phy4: ethernet-phy@1f { > + reg = <0x1f>; > + }; > +}; > + > +&i2c0 { > + status = "okay"; > + > + sfpgpio: gpio@76 { > + reg = <0x76>; > + compatible = "ti,tca9539"; We generally start property list with compatible. > + #gpio-cells = <2>; > + gpio-controller; > + > + admin_led_lower { > + gpio-hog; > + gpios = <13 GPIO_ACTIVE_HIGH>; > + output-low; > + }; > + }; > + > + tpm: at97sc@29 { > + reg = <0x29>; > + compatible = "atmel,at97sc3204t"; Ditto > + }; > +}; > + > +&i2c2 { > + status = "okay"; > + > + rtc: rx8035@32 { Node name should be generic while label can be specific, so 'rx8035: rtc@32' should make more sense. > + reg = <0x32>; > + compatible = "epson,rx8035"; > + }; > +}; > + > +&i2c3 { > + status = "okay"; > + > + i2c-switch@70 { > + compatible = "nxp,pca9540"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x70 >; > + > + sfpupper_i2c: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + }; > + > + sfplower_i2c: i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + }; > + }; > +}; > + > +&duart0 { Please try to sort these labeling nodes alphabetically. > + status = "okay"; > +}; > + > +&duart1 { > + status = "okay"; > +}; > + > +&esdhc { > + status = "okay"; > +}; > + > +&pcs_mdio1 { > + status = "okay"; > +}; > + > +&pcs_mdio2 { > + status = "okay"; > +}; > + > +&pcs_mdio3 { > + status = "okay"; > +}; > + > +&pcs_mdio7 { > + status = "okay"; > +}; > + > +&qspi { > + status = "okay"; > + > + en25s64: flash@0 { > + compatible = "jedec,spi-nor"; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <20000000>; > + spi-rx-bus-width = <4>; > + spi-tx-bus-width = <4>; > + reg = <0>; > + > + bl2@0 { Shouldn't the name be 'partition' just like nand flash below. > + label = "bl2"; > + reg = <0 0x100000>; > + }; > + > + bl3@100000 { > + label = "bl3"; > + reg = <0x100000 0x200000>; > + }; > + > + mcfirmware@300000 { > + label = "mcfirmware"; > + reg = <0x300000 0x200000>; > + }; > + > + ubootenv@500000 { > + label = "ubootenv"; > + reg = <0x500000 0x80000>; > + }; Missing newline. > + dpl@580000 { > + label = "dpl"; > + reg = <0x580000 0x40000>; > + }; > + > + dpc@5C0000 { > + label = "dpc"; > + reg = <0x5C0000 0x40000>; > + }; > + > + devicetree@600000 { > + label = "devicetree"; > + reg = <0x600000 0x40000>; > + }; > + }; > + > + nand: flash@1 { > + compatible = "spi-nand"; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <20000000>; > + reg = <1>; > + spi-rx-bus-width = <4>; > + spi-tx-bus-width = <4>; > + > + /* reserved for future boot direct from NAND flash > + * (this would use the same layout as the 8MiB NOR flash) > + */ > + partition@0 { > + label = "nand-boot-reserved"; > + reg = <0 0x800000>; > + }; > + > + /* recovery / install environment */ > + partition@800000 { > + label = "recovery"; > + reg = <0x800000 0x2000000>; > + }; > + > + /* ubia (first OpenWrt) - a/b names to prevent confusion with ubi0/1/etc. */ > + partition@2800000 { > + label = "ubia"; > + reg = <0x2800000 0x6C00000>; > + }; Have a newline. Shawn > + /* ubib (second OpenWrt) */ > + partition@9400000 { > + label = "ubib"; > + reg = <0x9400000 0x6C00000>; > + }; > + }; > +}; > + > +&usb0 { > + status = "okay"; > +}; > + > +&usb1 { > + status = "okay"; > +}; > -- > 2.30.1 >
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 25806c4924cb..2b3ee42e4a2a 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts new file mode 100644 index 000000000000..7f1584f378fe --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts @@ -0,0 +1,375 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for Travese Ten64 (LS1088) board + * Based on fsl-ls1088a-rdb.dts + * Copyright 2017-2020 NXP + * Copyright 2019-2021 Traverse Technologies + * + * Author: Mathew McBride <matt@traverse.com.au> + */ + +/dts-v1/; + +#include "fsl-ls1088a.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Traverse Ten64"; + compatible = "traverse,ten64", "fsl,ls1088a"; + + aliases { + serial0 = &duart0; + serial1 = &duart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + buttons { + compatible = "gpio-keys"; + /* Fired by system controller when + * external power off (e.g ATX Power Button) + * asserted + */ + powerdn { + label = "External Power Down"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>; + linux,code = <KEY_POWER>; + }; + + /* Rear Panel 'ADMIN' button (GPIO_H) */ + admin { + label = "ADMIN button"; + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>; + interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>; + linux,code = <KEY_WPS_BUTTON>; + }; + }; + + leds { + compatible = "gpio-leds"; + + sfp1down { + label = "ten64:green:sfp1:down"; + gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>; + }; + + sfp2up { + label = "ten64:green:sfp2:up"; + gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>; + }; + + admin { + label = "ten64:admin"; + gpios = <&sfpgpio 12 GPIO_ACTIVE_HIGH>; + }; + }; + + sfp_xg0: dpmac2_sfp { + compatible = "sff,sfp"; + i2c-bus = <&sfplower_i2c>; + tx-fault-gpios = <&sfpgpio 0 GPIO_ACTIVE_HIGH>; + tx-disable-gpios = <&sfpgpio 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sfpgpio 2 GPIO_ACTIVE_LOW>; + los-gpios = <&sfpgpio 3 GPIO_ACTIVE_HIGH>; + maximum-power-milliwatt = <2000>; + }; + + sfp_xg1: dpmac1_sfp { + compatible = "sff,sfp"; + i2c-bus = <&sfpupper_i2c>; + tx-fault-gpios = <&sfpgpio 4 GPIO_ACTIVE_HIGH>; + tx-disable-gpios = <&sfpgpio 5 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sfpgpio 6 GPIO_ACTIVE_LOW>; + los-gpios = <&sfpgpio 7 GPIO_ACTIVE_HIGH>; + maximum-power-milliwatt = <2000>; + }; + +}; + +/* XG1 - Upper SFP */ +&dpmac1 { + sfp = <&sfp_xg1>; + pcs-handle = <&pcs1>; + phy-connection-type = "10gbase-r"; + managed = "in-band-status"; +}; + +/* XG0 - Lower SFP */ +&dpmac2 { + sfp = <&sfp_xg0>; + pcs-handle = <&pcs2>; + phy-connection-type = "10gbase-r"; + managed = "in-band-status"; +}; + +/* DPMAC3..6 is GE4 to GE8 */ +&dpmac3 { + phy-handle = <&mdio1_phy5>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs3_0>; +}; + +&dpmac4 { + phy-handle = <&mdio1_phy6>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs3_1>; +}; + +&dpmac5 { + phy-handle = <&mdio1_phy7>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs3_2>; +}; + +&dpmac6 { + phy-handle = <&mdio1_phy8>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs3_3>; +}; + +/* DPMAC7..10 is GE0 to GE3 */ +&dpmac7 { + phy-handle = <&mdio1_phy1>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs7_0>; +}; + +&dpmac8 { + phy-handle = <&mdio1_phy2>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs7_1>; +}; + +&dpmac9 { + phy-handle = <&mdio1_phy3>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs7_2>; +}; + +&dpmac10 { + phy-handle = <&mdio1_phy4>; + phy-connection-type = "qsgmii"; + managed = "in-band-status"; + pcs-handle = <&pcs7_3>; +}; + +&emdio1 { + status = "okay"; + + mdio1_phy5: ethernet-phy@c { + reg = <0xc>; + }; + + mdio1_phy6: ethernet-phy@d { + reg = <0xd>; + }; + + mdio1_phy7: ethernet-phy@e { + reg = <0xe>; + }; + + mdio1_phy8: ethernet-phy@f { + reg = <0xf>; + }; + + mdio1_phy1: ethernet-phy@1c { + reg = <0x1c>; + }; + + mdio1_phy2: ethernet-phy@1d { + reg = <0x1d>; + }; + + mdio1_phy3: ethernet-phy@1e { + reg = <0x1e>; + }; + + mdio1_phy4: ethernet-phy@1f { + reg = <0x1f>; + }; +}; + +&i2c0 { + status = "okay"; + + sfpgpio: gpio@76 { + reg = <0x76>; + compatible = "ti,tca9539"; + #gpio-cells = <2>; + gpio-controller; + + admin_led_lower { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + }; + }; + + tpm: at97sc@29 { + reg = <0x29>; + compatible = "atmel,at97sc3204t"; + }; +}; + +&i2c2 { + status = "okay"; + + rtc: rx8035@32 { + reg = <0x32>; + compatible = "epson,rx8035"; + }; +}; + +&i2c3 { + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9540"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70 >; + + sfpupper_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + sfplower_i2c: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; + +&esdhc { + status = "okay"; +}; + +&pcs_mdio1 { + status = "okay"; +}; + +&pcs_mdio2 { + status = "okay"; +}; + +&pcs_mdio3 { + status = "okay"; +}; + +&pcs_mdio7 { + status = "okay"; +}; + +&qspi { + status = "okay"; + + en25s64: flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <20000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + reg = <0>; + + bl2@0 { + label = "bl2"; + reg = <0 0x100000>; + }; + + bl3@100000 { + label = "bl3"; + reg = <0x100000 0x200000>; + }; + + mcfirmware@300000 { + label = "mcfirmware"; + reg = <0x300000 0x200000>; + }; + + ubootenv@500000 { + label = "ubootenv"; + reg = <0x500000 0x80000>; + }; + dpl@580000 { + label = "dpl"; + reg = <0x580000 0x40000>; + }; + + dpc@5C0000 { + label = "dpc"; + reg = <0x5C0000 0x40000>; + }; + + devicetree@600000 { + label = "devicetree"; + reg = <0x600000 0x40000>; + }; + }; + + nand: flash@1 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <20000000>; + reg = <1>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + + /* reserved for future boot direct from NAND flash + * (this would use the same layout as the 8MiB NOR flash) + */ + partition@0 { + label = "nand-boot-reserved"; + reg = <0 0x800000>; + }; + + /* recovery / install environment */ + partition@800000 { + label = "recovery"; + reg = <0x800000 0x2000000>; + }; + + /* ubia (first OpenWrt) - a/b names to prevent confusion with ubi0/1/etc. */ + partition@2800000 { + label = "ubia"; + reg = <0x2800000 0x6C00000>; + }; + /* ubib (second OpenWrt) */ + partition@9400000 { + label = "ubib"; + reg = <0x9400000 0x6C00000>; + }; + }; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +};
The Traverse Technologies Ten64 is a Mini-ITX form factor networking board using the NXP LS1088A SoC. This device tree only describes features which the mainline kernel currently has support for, such as some I2C-connected devices that are not described at present. System documentation may be found at ten64doc.traverse.com.au Signed-off-by: Mathew McBride <matt@traverse.com.au> --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../boot/dts/freescale/fsl-ls1088a-ten64.dts | 375 ++++++++++++++++++ 2 files changed, 376 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts -- 2.30.1