diff mbox series

[v4,09/19] rtw89: add pci files

Message ID 20210429080149.7068-10-pkshih@realtek.com
State Superseded
Headers show
Series rtw89: add Realtek 802.11ax driver | expand

Commit Message

Ping-Ke Shih April 29, 2021, 8:01 a.m. UTC
DMA data to/from device via TX/RX rings. There are totally 13 TX rings --
8 AC rings, 2 MGMT rings, 2 HI rings and one FW CMD ring. There are
totally 2 RX rings -- one is RX ring, and the other is report ring.

FW CMD TX ring is a special TX ring that is used to download firmware or
send H2C to firmware. The other TX rings are used to send normal data(skb),
and if the skb is sent, RX report ring will receive a report that tells
driver to free the skb. Normal RX packets, C2H and PPDU status are
received by RX rings accordingly.

One TX ring contains TX BD and TX WD. Both are allocated by
dma_alloc_coherent(), but their size can be different (#TX_BD <= #TX_WD).
When a skb is going to send, use a tx_req to hold skb and corresponding
description data, and then fill the request data to a free TX BD and a
free TX WD, finally kick off the TX BD. When TX BD DMA is done, read index
of register is increasing, and then TX BD can be freed, but free WD and skb
until report is received.

Since CMD TX ring doesn't send normal data, it doesn't need to wait for
sending data in air. Therefore, TX BD, TX WD and cmd skb can be freed, when
read index of register is increasing.

One entry of RX ring contains a RX BD and a skb. The skb is used to store
RX WD and frame. RX BD is allocated by dma_alloc_coherent(), and fill RX
size and point RX DMA address to skb->data. If size of RX packet exceeds
filled RX size, the packet will be divided into multiple RX BD with FS and
LS bit.

TX BD OK interrupt for normal AC ring is masked out, because it causes
frequent context switch. We defer to reclaim it until report is received.
The exception is FW CMD ring that doesn't wait for report, so we reclaim
it in interrupt.

With wake TX queue, we submit a bunch of TX skb in one go, and then kick
off DMA by writing write index of TX BD after the TX BD/WD/skb are filled.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
---
 drivers/net/wireless/realtek/rtw89/pci.c | 2918 ++++++++++++++++++++++
 drivers/net/wireless/realtek/rtw89/pci.h |  565 +++++
 2 files changed, 3483 insertions(+)
 create mode 100644 drivers/net/wireless/realtek/rtw89/pci.c
 create mode 100644 drivers/net/wireless/realtek/rtw89/pci.h

Comments

Brian Norris June 10, 2021, 2:03 a.m. UTC | #1
Hi,

I'm slowly making my way through this series. I think a lot of this
looks a lot better than the first rtw88 submission I looked at, so
that's nice!

Mostly small notes for this patch, but a few larger questions about IRQ
handling and NAPI:

On Thu, Apr 29, 2021 at 04:01:39PM +0800, Ping-Ke Shih wrote:
> --- /dev/null

> +++ b/drivers/net/wireless/realtek/rtw89/pci.c


...

> +static void rtw89_pci_recognize_intrs(struct rtw89_dev *rtwdev,

> +				      struct rtw89_pci *rtwpci)

> +{

> +	rtwpci->halt_c2h_isrs = rtw89_read32(rtwdev, R_AX_HISR0) & rtwpci->halt_c2h_intrs;

> +	rtwpci->isrs[0] = rtw89_read32(rtwdev, R_AX_PCIE_HISR00) & rtwpci->intrs[0];

> +	rtwpci->isrs[1] = rtw89_read32(rtwdev, R_AX_PCIE_HISR10) & rtwpci->intrs[1];

> +}

> +

> +static void rtw89_pci_enable_intr(struct rtw89_dev *rtwdev,

> +				  struct rtw89_pci *rtwpci)

> +{

> +	rtw89_write32(rtwdev, R_AX_HIMR0, rtwpci->halt_c2h_intrs);

> +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, rtwpci->intrs[0]);

> +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, rtwpci->intrs[1]);

> +}

> +

> +static void rtw89_pci_enable_intr_unmask0(struct rtw89_dev *rtwdev,

> +					  struct rtw89_pci *rtwpci, u32 unmask0)

> +{

> +	rtwpci->intrs[0] &= ~unmask0;


I might be misreading something, but I believe "mask" (as in, "mask
an interrupt") is usually meant as "disable" -- see, for instance, the
conventions in 'struct irq_chip' -- and this looks like you're using the
term "unmask" to mean disable. This confuses my reading of code that
calls this function.

I'd suggest either swapping the names (unmask vs. mask) or else pick an
independent name ("rx on" and "rx off"? something based on "on/off",
"disable/enable"? "set/clear"?).

> +	rtw89_pci_enable_intr(rtwdev, rtwpci);

> +}

> +

> +static void rtw89_pci_enable_intr_mask0(struct rtw89_dev *rtwdev,

> +					struct rtw89_pci *rtwpci, u32 mask0)

> +{

> +	rtwpci->intrs[0] |= mask0;

> +	rtw89_pci_enable_intr(rtwdev, rtwpci);

> +}

> +

> +static void rtw89_pci_disable_intr(struct rtw89_dev *rtwdev,

> +				   struct rtw89_pci *rtwpci)

> +{

> +	rtw89_write32(rtwdev, R_AX_HIMR0, 0);

> +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, 0);

> +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, 0);

> +}

> +

> +static void rtw89_pci_try_napi_schedule(struct rtw89_dev *rtwdev, u32 *unmask0_rx)

> +{

> +	if (*unmask0_rx && !napi_reschedule(&rtwdev->napi)) {

> +		/* if can't invoke napi, RX_IMR must be off already */

> +		*unmask0_rx = 0;

> +	}

> +}

> +

> +static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)

> +{

> +	struct rtw89_dev *rtwdev = dev;

> +	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> +	u32 isrs[2];

> +	unsigned long flags;

> +	u32 unmask0_rx = 0;

> +

> +	isrs[0] = rtwpci->isrs[0];

> +	isrs[1] = rtwpci->isrs[1];

> +

> +	/* TX ISR */

> +	if (isrs[0] & B_AX_TXDMA_CH12_INT)

> +		rtw89_pci_isr_txch_dma(rtwdev, rtwpci, RTW89_TXCH_CH12);

> +

> +	/* RX ISR */

> +	if (isrs[0] & (B_AX_RXDMA_INT | B_AX_RXP1DMA_INT))

> +		unmask0_rx = B_AX_RXDMA_INTS_MASK;

> +	if (isrs[0] & B_AX_RPQDMA_INT)

> +		rtw89_pci_isr_rpq_dma(rtwdev, rtwpci);

> +	if (isrs[0] & B_AX_RDU_INT) {

> +		rtw89_pci_isr_rxd_unavail(rtwdev, rtwpci);

> +		unmask0_rx = B_AX_RXDMA_INTS_MASK;

> +	}

> +

> +	if (rtwpci->halt_c2h_isrs & B_AX_HALT_C2H_INT_EN)

> +		rtw89_ser_notify(rtwdev, rtw89_mac_get_err_status(rtwdev));

> +

> +	/* invoke napi and disable rx_imr within bh_disable, because we must

> +	 * ensure napi_poll re-enable rx_imr after this.

> +	 */

> +	local_bh_disable();


I'm not sure I understand this; disabling BH isn't enough to ensure NAPI
contexts aren't running in parallel with this -- that's what a lock is
for. And, you're already holding irq_lock.

The other part of this problem (I think) is that you have the ordering
wrong here -- don't you want to set the interrupt state *before*
scheduling NAPI? That way, if an RX event comes while we're doing this,
we know that either the NAPI context is still running or scheduled (and
will re-enable the RX interrupt when done), or else we're going to
schedule a new poll (which will eventually re-enable the interrupt).

In other words, I think you should
1. drop the BH disable/enable
2. set the interrupt state first, followed by napi_schedule() (if there
   was an RX IRQ pending)
3. stop trying to look at the napi_reschedule() return value (i.e., just
   use napi_schedule())

Am I missing something? I'm just trying to reason through the code here;
I haven't stress-tested my suggestsions or anything, nor experienced
whatever problem you were trying to solve here.

> +	spin_lock_irqsave(&rtwpci->irq_lock, flags);

> +	rtw89_pci_try_napi_schedule(rtwdev, &unmask0_rx);

> +	if (rtwpci->running) {

> +		rtw89_pci_clear_intrs(rtwdev, rtwpci);

> +		rtw89_pci_enable_intr_unmask0(rtwdev, rtwpci, unmask0_rx);

> +	}

> +	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);

> +	local_bh_enable();

> +

> +	return IRQ_HANDLED;

> +}


...

> +static u32 rtw89_pci_ops_read32_cmac(struct rtw89_dev *rtwdev, u32 addr)

> +{

> +	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> +	u32 val = readl(rtwpci->mmap + addr);

> +	int count;

> +

> +	for (count = 0; ; count++) {

> +		if (val != RTW89_R32_DEAD)

> +			return val;

> +		if (count >= MAC_REG_POOL_COUNT) {

> +			rtw89_warn(rtwdev, "addr 0x%x = 0xdeadbeef\n", addr);


I understand this is a constant, but it might be better to either
stringify the macro:

			rtw89_warn(rtwdev, "addr %#x = " #RTW89_R32_DEAD "\n", addr);

or just use val:

			rtw89_warn(rtwdev, "addr %#x = %#x\n", addr, val);

> +			return RTW89_R32_DEAD;

> +		}

> +		rtw89_pci_ops_write32(rtwdev, R_AX_CK_EN, B_AX_CMAC_ALLCKEN);

> +		val = readl(rtwpci->mmap + addr);

> +	}

> +

> +	return val;

> +}


...

> +static int

> +rtw89_read16_mdio(struct rtw89_dev *rtwdev, u8 addr, u8 speed, u16 *val)

> +{

> +	int ret;

> +

> +	ret = rtw89_pci_check_mdio(rtwdev, addr, speed, B_AX_MDIO_RFLAG);

> +	if (ret) {

> +		rtw89_err(rtwdev, "[ERR]MDIO R16 0x%X fail!\n", addr);


Dump |ret|?

> +		return ret;

> +	}

> +	*val = rtw89_read16(rtwdev, R_AX_MDIO_RDATA);

> +

> +	return 0;

> +}


...

> +static int rtw89_dbi_read8(struct rtw89_dev *rtwdev, u16 addr, u8 *value)

> +{

> +	u16 read_addr = addr & B_AX_DBI_ADDR_MSK;

> +	u8 flag;

> +	int ret;

> +

> +	rtw89_write16(rtwdev, R_AX_DBI_FLAG, read_addr);

> +	rtw89_write8(rtwdev, R_AX_DBI_FLAG + 2, B_AX_DBI_RFLAG >> 16);

> +

> +	ret = read_poll_timeout_atomic(rtw89_read8, flag, !flag, 10,

> +				       10 * RTW89_PCI_WR_RETRY_CNT, false,

> +				       rtwdev, R_AX_DBI_FLAG + 2);

> +

> +	if (!ret) {

> +		read_addr = R_AX_DBI_RDATA + (addr & 3);

> +		*value = rtw89_read8(rtwdev, read_addr);

> +	} else {

> +		WARN(1, "failed to read DBI register, addr=0x%04x\n", addr);

> +		ret =  -EIO;


You've got some weird whitespace here and a few other places. Search for
the string "=  " (2 spaces) -- there should only be 1.

> +	}

> +

> +	return ret;

> +}

> +

> +static int

> +__get_target(struct rtw89_dev *rtwdev, u16 *target, enum rtw89_pcie_phy phy_rate)

> +{

> +	u16 val, tar;

> +	int ret;

> +

> +	/* Enable counter */

> +	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val);

> +	if (ret)

> +		return ret;

> +	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val & ~BIT(12),


You mostly do a good job on using macros with meaningful names instead
of magic numbers, but you've still got quite a few uses of BIT() that
probably should be macros. I'd suggest taking another pass through this
driver for usages of raw BIT() and GENMASK(), and see where it's
reasonable to add macro names (either in the .c file if it's a very
local usage, or just add to the .h next to the register definitions).

> +				 phy_rate);

...
> +}

> +

> +static int rtw89_pci_auto_refclk_cal(struct rtw89_dev *rtwdev, bool autook_en)

> +{

> +	enum rtw89_pcie_phy phy_rate;

> +	u16 val16, mgn_set, div_set, tar;

> +	u8 val8, bdr_ori;

> +	bool l1_flag = false;

> +	int ret = 0;

> +

> +	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_PHY_RATE, &val8);

> +	if (ret) {

> +		rtw89_err(rtwdev, "[ERR]dbi_r8_pcie %X\n", RTW89_PCIE_PHY_RATE);

> +		return ret;

> +	}

> +

> +	if (FIELD_GET(GENMASK(1, 0), val8) == 0x1) {

> +		phy_rate = PCIE_PHY_GEN1;

> +	} else if (FIELD_GET(GENMASK(1, 0), val8) == 0x2) {

> +		phy_rate = PCIE_PHY_GEN2;

> +	} else {

> +		rtw89_err(rtwdev, "[ERR]PCIe PHY rate not support\n");


Dump the value of |val8| in this error message? Also, this probably
makes more sense as "not supported".

> +		return -EOPNOTSUPP;

> +	}

...
> +	/*  Obtain div and margin */


Extra space.

...

> +static int rtw89_pci_napi_poll(struct napi_struct *napi, int budget)

> +{

> +	struct rtw89_dev *rtwdev = container_of(napi, struct rtw89_dev, napi);

> +	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> +	unsigned long flags;

> +	u32 cnt;

> +	int ret;

> +

> +	ret = rtw89_pci_poll_rxq_dma(rtwdev, rtwpci, budget);

> +	if (ret < budget) {

> +		napi_complete_done(napi, ret);

> +

> +		cnt = rtw89_pci_rxbd_recalc(rtwdev, &rtwpci->rx_rings[RTW89_RXCH_RXQ]);

> +		if (cnt && napi_reschedule(napi))

> +			return ret;

> +

> +		spin_lock_irqsave(&rtwpci->irq_lock, flags);

> +		if (rtwpci->running) {

> +			rtw89_pci_clear_intrs(rtwdev, rtwpci);


Do you really want to clear interrupts here? I'm not that familiar with
the hardware here or anything, but that seems like a job for your ISR,
not the NAPI poll. It also seems like you might double-clear interrupts
without properly handling them, because you only called
rtw89_pci_recognize_intrs() in the ISR, not here.

> +			rtw89_pci_enable_intr_mask0(rtwdev, rtwpci, B_AX_RXDMA_INTS_MASK);

> +		}

> +		spin_unlock_irqrestore(&rtwpci->irq_lock, flags);

> +	}

> +

> +	return ret;

> +}


...

> +static void rtw89_pci_remove(struct pci_dev *pdev)

> +{

> +	struct ieee80211_hw *hw = pci_get_drvdata(pdev);

> +	struct rtw89_dev *rtwdev;

> +

> +	if (!hw)

> +		return;


Is this even possible (hw==NULL)? You always "set" this when probe() is
successful, so remove() should only be called with a non-NULL drvdata.

> +

> +	rtwdev = hw->priv;

> +

> +	rtw89_pci_free_irq(rtwdev, pdev);

> +	rtw89_core_napi_deinit(rtwdev);

> +	rtw89_core_unregister(rtwdev);

> +	rtw89_pci_clear_resource(rtwdev, pdev);

> +	rtw89_pci_declaim_device(rtwdev, pdev);

> +	rtw89_core_deinit(rtwdev);

> +	ieee80211_free_hw(hw);

> +}


Brian
Ping-Ke Shih June 16, 2021, 8:31 a.m. UTC | #2
> -----Original Message-----

> From: Brian Norris [mailto:briannorris@chromium.org]

> Sent: Thursday, June 10, 2021 10:04 AM

> To: Pkshih

> Cc: kvalo@codeaurora.org; linux-wireless@vger.kernel.org

> Subject: Re: [PATCH v4 09/19] rtw89: add pci files

> 

> Hi,

> 

> I'm slowly making my way through this series. I think a lot of this

> looks a lot better than the first rtw88 submission I looked at, so

> that's nice!

> 

> Mostly small notes for this patch, but a few larger questions about IRQ

> handling and NAPI:

> 

> On Thu, Apr 29, 2021 at 04:01:39PM +0800, Ping-Ke Shih wrote:

> > --- /dev/null

> > +++ b/drivers/net/wireless/realtek/rtw89/pci.c

> 

> ...

> 

> > +static void rtw89_pci_recognize_intrs(struct rtw89_dev *rtwdev,

> > +				      struct rtw89_pci *rtwpci)

> > +{

> > +	rtwpci->halt_c2h_isrs = rtw89_read32(rtwdev, R_AX_HISR0) & rtwpci->halt_c2h_intrs;

> > +	rtwpci->isrs[0] = rtw89_read32(rtwdev, R_AX_PCIE_HISR00) & rtwpci->intrs[0];

> > +	rtwpci->isrs[1] = rtw89_read32(rtwdev, R_AX_PCIE_HISR10) & rtwpci->intrs[1];

> > +}

> > +

> > +static void rtw89_pci_enable_intr(struct rtw89_dev *rtwdev,

> > +				  struct rtw89_pci *rtwpci)

> > +{

> > +	rtw89_write32(rtwdev, R_AX_HIMR0, rtwpci->halt_c2h_intrs);

> > +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, rtwpci->intrs[0]);

> > +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, rtwpci->intrs[1]);

> > +}

> > +

> > +static void rtw89_pci_enable_intr_unmask0(struct rtw89_dev *rtwdev,

> > +					  struct rtw89_pci *rtwpci, u32 unmask0)

> > +{

> > +	rtwpci->intrs[0] &= ~unmask0;

> 

> I might be misreading something, but I believe "mask" (as in, "mask

> an interrupt") is usually meant as "disable" -- see, for instance, the

> conventions in 'struct irq_chip' -- and this looks like you're using the

> term "unmask" to mean disable. This confuses my reading of code that

> calls this function.

> 

> I'd suggest either swapping the names (unmask vs. mask) or else pick an

> independent name ("rx on" and "rx off"? something based on "on/off",

> "disable/enable"? "set/clear"?).

> 


Understand.
I'll refine the interrupt and NAPI flow (see below), and I suppose these functions
will be removed, so I don't change the names right away.

> > +	rtw89_pci_enable_intr(rtwdev, rtwpci);

> > +}

> > +

> > +static void rtw89_pci_enable_intr_mask0(struct rtw89_dev *rtwdev,

> > +					struct rtw89_pci *rtwpci, u32 mask0)

> > +{

> > +	rtwpci->intrs[0] |= mask0;

> > +	rtw89_pci_enable_intr(rtwdev, rtwpci);

> > +}

> > +

> > +static void rtw89_pci_disable_intr(struct rtw89_dev *rtwdev,

> > +				   struct rtw89_pci *rtwpci)

> > +{

> > +	rtw89_write32(rtwdev, R_AX_HIMR0, 0);

> > +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, 0);

> > +	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, 0);

> > +}

> > +

> > +static void rtw89_pci_try_napi_schedule(struct rtw89_dev *rtwdev, u32 *unmask0_rx)

> > +{

> > +	if (*unmask0_rx && !napi_reschedule(&rtwdev->napi)) {

> > +		/* if can't invoke napi, RX_IMR must be off already */

> > +		*unmask0_rx = 0;

> > +	}

> > +}

> > +

> > +static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)

> > +{

> > +	struct rtw89_dev *rtwdev = dev;

> > +	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> > +	u32 isrs[2];

> > +	unsigned long flags;

> > +	u32 unmask0_rx = 0;

> > +

> > +	isrs[0] = rtwpci->isrs[0];

> > +	isrs[1] = rtwpci->isrs[1];

> > +

> > +	/* TX ISR */

> > +	if (isrs[0] & B_AX_TXDMA_CH12_INT)

> > +		rtw89_pci_isr_txch_dma(rtwdev, rtwpci, RTW89_TXCH_CH12);

> > +

> > +	/* RX ISR */

> > +	if (isrs[0] & (B_AX_RXDMA_INT | B_AX_RXP1DMA_INT))

> > +		unmask0_rx = B_AX_RXDMA_INTS_MASK;

> > +	if (isrs[0] & B_AX_RPQDMA_INT)

> > +		rtw89_pci_isr_rpq_dma(rtwdev, rtwpci);

> > +	if (isrs[0] & B_AX_RDU_INT) {

> > +		rtw89_pci_isr_rxd_unavail(rtwdev, rtwpci);

> > +		unmask0_rx = B_AX_RXDMA_INTS_MASK;

> > +	}

> > +

> > +	if (rtwpci->halt_c2h_isrs & B_AX_HALT_C2H_INT_EN)

> > +		rtw89_ser_notify(rtwdev, rtw89_mac_get_err_status(rtwdev));

> > +

> > +	/* invoke napi and disable rx_imr within bh_disable, because we must

> > +	 * ensure napi_poll re-enable rx_imr after this.

> > +	 */

> > +	local_bh_disable();

> 

> I'm not sure I understand this; disabling BH isn't enough to ensure NAPI

> contexts aren't running in parallel with this -- that's what a lock is

> for. And, you're already holding irq_lock.

> 

> The other part of this problem (I think) is that you have the ordering

> wrong here -- don't you want to set the interrupt state *before*

> scheduling NAPI? That way, if an RX event comes while we're doing this,

> we know that either the NAPI context is still running or scheduled (and

> will re-enable the RX interrupt when done), or else we're going to

> schedule a new poll (which will eventually re-enable the interrupt).

> 

> In other words, I think you should

> 1. drop the BH disable/enable

> 2. set the interrupt state first, followed by napi_schedule() (if there

>    was an RX IRQ pending)

> 3. stop trying to look at the napi_reschedule() return value (i.e., just

>    use napi_schedule())

> 

> Am I missing something? I'm just trying to reason through the code here;

> I haven't stress-tested my suggestsions or anything, nor experienced

> whatever problem you were trying to solve here.


By your suggestions, I trace the flow and picture them below:

int_handler             int_threadfn              napi_poll
-----------             ------------              ---------
    |
    |
    | 1) dis. intr
    | 2) read status
    o                      |
                           | 3) do TX reclaim
                           | 4) check if RX?
                           | 5) re-enable intr
                           |    (RX is optional)
                           | 6) schedule_napi
                           |    (if RX)
                           : >>>-------------------+ 7) (tasklet start immediately)
                           :                       | 
                           :                       | 8) do RX things
                           :                       | 9) re-enable intr of RX
                           :                       |
                           : <<<-------------------o
                           :
                           o

In my preliminary test, it works as above flow normally.
But, three exceptions
1. interrupt is still triggered, even we disable interrupt by step 1).
   That means int_handler is executed again, but threadfn doesn't enable
   interrupt yet.
   This is because interrupt event is on the way to host (I think the path is
   long -- from WiFi MAC to PCI MAC to PCI bus to host).
   There's race condition between disable interrupt and interrupt event.

   I don't plan to fix the race condition, but make the driver handle it properly.

2. napi_poll doesn't start immediately at the step 7).
   I don't trace the reason yet, but I think it's reasonable that
   int_threadfn and napi_poll can be ansynchronous.
   Because napi_poll can run in threaded mode as well.

3. Since int_threadfn and napi_poll are ansynchronous (similar to exception 2),
   it looks like napi_poll is done before int_threadfn in some situations.

I'll make the driver handle these cases in next submission (v6).

Another thing is I need to do local_bh_disable() before calling napi_schedule(),
or kernel warns " NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!"
I think this is because __napi_schedule() does local_irq_save(), not very sure.

I investigate other drivers that use napi_schedule() also do local_bh_disable()
before calling napi_schedule(), or do spin_lock_bh(), or in bh context. I think
these are equivalent. 

> 

> > +	spin_lock_irqsave(&rtwpci->irq_lock, flags);

> > +	rtw89_pci_try_napi_schedule(rtwdev, &unmask0_rx);

> > +	if (rtwpci->running) {

> > +		rtw89_pci_clear_intrs(rtwdev, rtwpci);

> > +		rtw89_pci_enable_intr_unmask0(rtwdev, rtwpci, unmask0_rx);

> > +	}

> > +	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);

> > +	local_bh_enable();

> > +

> > +	return IRQ_HANDLED;

> > +}

> 

> ...

> 

> > +static u32 rtw89_pci_ops_read32_cmac(struct rtw89_dev *rtwdev, u32 addr)

> > +{

> > +	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> > +	u32 val = readl(rtwpci->mmap + addr);

> > +	int count;

> > +

> > +	for (count = 0; ; count++) {

> > +		if (val != RTW89_R32_DEAD)

> > +			return val;

> > +		if (count >= MAC_REG_POOL_COUNT) {

> > +			rtw89_warn(rtwdev, "addr 0x%x = 0xdeadbeef\n", addr);

> 

> I understand this is a constant, but it might be better to either

> stringify the macro:

> 

> 			rtw89_warn(rtwdev, "addr %#x = " #RTW89_R32_DEAD "\n", addr);

> 

> or just use val:

> 

> 			rtw89_warn(rtwdev, "addr %#x = %#x\n", addr, val);

> 


Will do it.

> > +			return RTW89_R32_DEAD;

> > +		}

> > +		rtw89_pci_ops_write32(rtwdev, R_AX_CK_EN, B_AX_CMAC_ALLCKEN);

> > +		val = readl(rtwpci->mmap + addr);

> > +	}

> > +

> > +	return val;

> > +}

> 

> ...

> 

> > +static int

> > +rtw89_read16_mdio(struct rtw89_dev *rtwdev, u8 addr, u8 speed, u16 *val)

> > +{

> > +	int ret;

> > +

> > +	ret = rtw89_pci_check_mdio(rtwdev, addr, speed, B_AX_MDIO_RFLAG);

> > +	if (ret) {

> > +		rtw89_err(rtwdev, "[ERR]MDIO R16 0x%X fail!\n", addr);

> 

> Dump |ret|?


Okay

> 

> > +		return ret;

> > +	}

> > +	*val = rtw89_read16(rtwdev, R_AX_MDIO_RDATA);

> > +

> > +	return 0;

> > +}

> 

> ...

> 

> > +static int rtw89_dbi_read8(struct rtw89_dev *rtwdev, u16 addr, u8 *value)

> > +{

> > +	u16 read_addr = addr & B_AX_DBI_ADDR_MSK;

> > +	u8 flag;

> > +	int ret;

> > +

> > +	rtw89_write16(rtwdev, R_AX_DBI_FLAG, read_addr);

> > +	rtw89_write8(rtwdev, R_AX_DBI_FLAG + 2, B_AX_DBI_RFLAG >> 16);

> > +

> > +	ret = read_poll_timeout_atomic(rtw89_read8, flag, !flag, 10,

> > +				       10 * RTW89_PCI_WR_RETRY_CNT, false,

> > +				       rtwdev, R_AX_DBI_FLAG + 2);

> > +

> > +	if (!ret) {

> > +		read_addr = R_AX_DBI_RDATA + (addr & 3);

> > +		*value = rtw89_read8(rtwdev, read_addr);

> > +	} else {

> > +		WARN(1, "failed to read DBI register, addr=0x%04x\n", addr);

> > +		ret =  -EIO;

> 

> You've got some weird whitespace here and a few other places. Search for

> the string "=  " (2 spaces) -- there should only be 1.


Fixed

> 

> > +	}

> > +

> > +	return ret;

> > +}

> > +

> > +static int

> > +__get_target(struct rtw89_dev *rtwdev, u16 *target, enum rtw89_pcie_phy phy_rate)

> > +{

> > +	u16 val, tar;

> > +	int ret;

> > +

> > +	/* Enable counter */

> > +	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val);

> > +	if (ret)

> > +		return ret;

> > +	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val & ~BIT(12),

> 

> You mostly do a good job on using macros with meaningful names instead

> of magic numbers, but you've still got quite a few uses of BIT() that

> probably should be macros. I'd suggest taking another pass through this

> driver for usages of raw BIT() and GENMASK(), and see where it's

> reasonable to add macro names (either in the .c file if it's a very

> local usage, or just add to the .h next to the register definitions).


I fix pci.c first, and I will pass through whole driver in next submission.

> 

> > +				 phy_rate);

> ...

> > +}

> > +

> > +static int rtw89_pci_auto_refclk_cal(struct rtw89_dev *rtwdev, bool autook_en)

> > +{

> > +	enum rtw89_pcie_phy phy_rate;

> > +	u16 val16, mgn_set, div_set, tar;

> > +	u8 val8, bdr_ori;

> > +	bool l1_flag = false;

> > +	int ret = 0;

> > +

> > +	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_PHY_RATE, &val8);

> > +	if (ret) {

> > +		rtw89_err(rtwdev, "[ERR]dbi_r8_pcie %X\n", RTW89_PCIE_PHY_RATE);

> > +		return ret;

> > +	}

> > +

> > +	if (FIELD_GET(GENMASK(1, 0), val8) == 0x1) {

> > +		phy_rate = PCIE_PHY_GEN1;

> > +	} else if (FIELD_GET(GENMASK(1, 0), val8) == 0x2) {

> > +		phy_rate = PCIE_PHY_GEN2;

> > +	} else {

> > +		rtw89_err(rtwdev, "[ERR]PCIe PHY rate not support\n");

> 

> Dump the value of |val8| in this error message? Also, this probably

> makes more sense as "not supported".


Added.

> 

> > +		return -EOPNOTSUPP;

> > +	}

> ...

> > +	/*  Obtain div and margin */

> 

> Extra space.


Fixed

> 

> ...

> 

> > +static int rtw89_pci_napi_poll(struct napi_struct *napi, int budget)

> > +{

> > +	struct rtw89_dev *rtwdev = container_of(napi, struct rtw89_dev, napi);

> > +	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> > +	unsigned long flags;

> > +	u32 cnt;

> > +	int ret;

> > +

> > +	ret = rtw89_pci_poll_rxq_dma(rtwdev, rtwpci, budget);

> > +	if (ret < budget) {

> > +		napi_complete_done(napi, ret);

> > +

> > +		cnt = rtw89_pci_rxbd_recalc(rtwdev, &rtwpci->rx_rings[RTW89_RXCH_RXQ]);

> > +		if (cnt && napi_reschedule(napi))

> > +			return ret;

> > +

> > +		spin_lock_irqsave(&rtwpci->irq_lock, flags);

> > +		if (rtwpci->running) {

> > +			rtw89_pci_clear_intrs(rtwdev, rtwpci);

> 

> Do you really want to clear interrupts here? I'm not that familiar with

> the hardware here or anything, but that seems like a job for your ISR,

> not the NAPI poll. It also seems like you might double-clear interrupts

> without properly handling them, because you only called

> rtw89_pci_recognize_intrs() in the ISR, not here.


This chip is an edge-trigger interrupt, so originally I'd like to make "(IMR & ISR)"
become 0, and then next RX packet can trigger the interrupt.
But, it seems that enable RX interrupt (step 9 of above picture) can already 
raise interrupt.

> 

> > +			rtw89_pci_enable_intr_mask0(rtwdev, rtwpci, B_AX_RXDMA_INTS_MASK);

> > +		}

> > +		spin_unlock_irqrestore(&rtwpci->irq_lock, flags);

> > +	}

> > +

> > +	return ret;

> > +}

> 

> ...

> 

> > +static void rtw89_pci_remove(struct pci_dev *pdev)

> > +{

> > +	struct ieee80211_hw *hw = pci_get_drvdata(pdev);

> > +	struct rtw89_dev *rtwdev;

> > +

> > +	if (!hw)

> > +		return;

> 

> Is this even possible (hw==NULL)? You always "set" this when probe() is

> successful, so remove() should only be called with a non-NULL drvdata.


Removed.
I have confirmed if probe() is unsuccessful, kernel won't call remove().

> 

> > +

> > +	rtwdev = hw->priv;

> > +

> > +	rtw89_pci_free_irq(rtwdev, pdev);

> > +	rtw89_core_napi_deinit(rtwdev);

> > +	rtw89_core_unregister(rtwdev);

> > +	rtw89_pci_clear_resource(rtwdev, pdev);

> > +	rtw89_pci_declaim_device(rtwdev, pdev);

> > +	rtw89_core_deinit(rtwdev);

> > +	ieee80211_free_hw(hw);

> > +}

> 

> Brian

> ------Please consider the environment before printing this e-mail.
Brian Norris June 18, 2021, 7:13 p.m. UTC | #3
On Wed, Jun 16, 2021 at 1:31 AM Pkshih <pkshih@realtek.com> wrote:
> > -----Original Message-----

> > From: Brian Norris [mailto:briannorris@chromium.org]


> > On Thu, Apr 29, 2021 at 04:01:39PM +0800, Ping-Ke Shih wrote:

> > > --- /dev/null

> > > +++ b/drivers/net/wireless/realtek/rtw89/pci.c

> > > +static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)

> > > +{

> > > +   struct rtw89_dev *rtwdev = dev;

> > > +   struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> > > +   u32 isrs[2];

> > > +   unsigned long flags;

> > > +   u32 unmask0_rx = 0;

> > > +

> > > +   isrs[0] = rtwpci->isrs[0];

> > > +   isrs[1] = rtwpci->isrs[1];


By the way, I'm pretty sure you need to hold the irq_lock to safely read these.

...

> By your suggestions, I trace the flow and picture them below:


Nice, thanks for that!

> But, three exceptions

> 1. interrupt is still triggered, even we disable interrupt by step 1).

>    That means int_handler is executed again, but threadfn doesn't enable

>    interrupt yet.


I think maybe that's what IRQF_ONESHOT is for? Do you need to use
that? But it might not be a complete solution.

>    This is because interrupt event is on the way to host (I think the path is

>    long -- from WiFi MAC to PCI MAC to PCI bus to host).

>    There's race condition between disable interrupt and interrupt event.

>

>    I don't plan to fix the race condition, but make the driver handle it properly.

>

> 2. napi_poll doesn't start immediately at the step 7).

>    I don't trace the reason yet, but I think it's reasonable that

>    int_threadfn and napi_poll can be ansynchronous.

>    Because napi_poll can run in threaded mode as well.

>

> 3. Since int_threadfn and napi_poll are ansynchronous (similar to exception 2),

>    it looks like napi_poll is done before int_threadfn in some situations.

>

> I'll make the driver handle these cases in next submission (v6).


ACK.

> Another thing is I need to do local_bh_disable() before calling napi_schedule(),

> or kernel warns " NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!"

> I think this is because __napi_schedule() does local_irq_save(), not very sure.

>

> I investigate other drivers that use napi_schedule() also do local_bh_disable()

> before calling napi_schedule(), or do spin_lock_bh(), or in bh context. I think

> these are equivalent.


OK. I'll admit I'm not that familiar with the locking and context
expectations of NAPI APIs (and, they are basically undocumented), but
that sounds OK. I was mostly concerned that you were trying to use
BH-disable as a mutual exclusion mechanism, when that's not really
what it does.

> > > +           spin_lock_irqsave(&rtwpci->irq_lock, flags);

> > > +           if (rtwpci->running) {

> > > +                   rtw89_pci_clear_intrs(rtwdev, rtwpci);

> >

> > Do you really want to clear interrupts here? I'm not that familiar with

> > the hardware here or anything, but that seems like a job for your ISR,

> > not the NAPI poll. It also seems like you might double-clear interrupts

> > without properly handling them, because you only called

> > rtw89_pci_recognize_intrs() in the ISR, not here.

>

> This chip is an edge-trigger interrupt, so originally I'd like to make "(IMR & ISR)"

> become 0, and then next RX packet can trigger the interrupt.


But I believe that's racy. If you clear an interrupt now based on
rtwpci->halt_c2h_isr and rtwpci->isrs[], and later reread those fields
in rtw89_pci_recognize_intrs(), clobbering any saved values, then you
may lose an interrupt, I think.

Overall, the state you're keeping around, and all the interactions
between your NAPI poll and your IRQ handler, are very complex and hard
to reason about. I believe your rtw88 driver has a much cleaner
interrupt dispatch logic -- it doesn't try to do smart things around
reading/writing the interrupt mask in 3 different places (IRQ handler,
threaded IRQ handler, and NAPI poll), but just read/stashes/clears the
mask in one place (threadfn) and avoids saving that state globally. I
think you might have better luck if you can imitate that. But again,
maybe I'm missing something.

Brian

> But, it seems that enable RX interrupt (step 9 of above picture) can already

> raise interrupt.
Ping-Ke Shih June 25, 2021, 10:07 a.m. UTC | #4
> -----Original Message-----

> From: Brian Norris [mailto:briannorris@chromium.org]

> Sent: Saturday, June 19, 2021 3:13 AM

> To: Pkshih

> Cc: kvalo@codeaurora.org; linux-wireless@vger.kernel.org

> Subject: Re: [PATCH v4 09/19] rtw89: add pci files

> 

>  On Wed, Jun 16, 2021 at 1:31 AM Pkshih <pkshih@realtek.com> wrote:

> > > -----Original Message-----

> > > From: Brian Norris [mailto:briannorris@chromium.org]

> 

> > > On Thu, Apr 29, 2021 at 04:01:39PM +0800, Ping-Ke Shih wrote:

> > > > --- /dev/null

> > > > +++ b/drivers/net/wireless/realtek/rtw89/pci.c

> > > > +static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)

> > > > +{

> > > > +   struct rtw89_dev *rtwdev = dev;

> > > > +   struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> > > > +   u32 isrs[2];

> > > > +   unsigned long flags;

> > > > +   u32 unmask0_rx = 0;

> > > > +

> > > > +   isrs[0] = rtwpci->isrs[0];

> > > > +   isrs[1] = rtwpci->isrs[1];

> 

> By the way, I'm pretty sure you need to hold the irq_lock to safely read these.

> 


Will do it.

> ...

> 

> > By your suggestions, I trace the flow and picture them below:

> 

> Nice, thanks for that!

> 

> > But, three exceptions

> > 1. interrupt is still triggered, even we disable interrupt by step 1).

> >    That means int_handler is executed again, but threadfn doesn't enable

> >    interrupt yet.

> 

> I think maybe that's what IRQF_ONESHOT is for? Do you need to use

> that? But it might not be a complete solution.

> 


I tried IRQF_ONESHOT and it works well. But this flag is mutual exclusive with
IRQF_SHARED that is in use.

I compare the interrupt count between these two flags, there is no significant
difference when I running TCP/UDP TX/RX stress test. Surprisingly, interrupt
count of using IRQF_SHARED is a little lower.

Since new flow (see below) can properly handle this case, I decide to use
original flag IRQF_SHARED.


> >    This is because interrupt event is on the way to host (I think the path is

> >    long -- from WiFi MAC to PCI MAC to PCI bus to host).

> >    There's race condition between disable interrupt and interrupt event.

> >

> >    I don't plan to fix the race condition, but make the driver handle it properly.

> >

> > 2. napi_poll doesn't start immediately at the step 7).

> >    I don't trace the reason yet, but I think it's reasonable that

> >    int_threadfn and napi_poll can be ansynchronous.

> >    Because napi_poll can run in threaded mode as well.

> >

> > 3. Since int_threadfn and napi_poll are ansynchronous (similar to exception 2),

> >    it looks like napi_poll is done before int_threadfn in some situations.

> >

> > I'll make the driver handle these cases in next submission (v6).

> 

> ACK.

> 

> > Another thing is I need to do local_bh_disable() before calling napi_schedule(),

> > or kernel warns " NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!"

> > I think this is because __napi_schedule() does local_irq_save(), not very sure.

> >

> > I investigate other drivers that use napi_schedule() also do local_bh_disable()

> > before calling napi_schedule(), or do spin_lock_bh(), or in bh context. I think

> > these are equivalent.

> 

> OK. I'll admit I'm not that familiar with the locking and context

> expectations of NAPI APIs (and, they are basically undocumented), but

> that sounds OK. I was mostly concerned that you were trying to use

> BH-disable as a mutual exclusion mechanism, when that's not really

> what it does.

> 

> > > > +           spin_lock_irqsave(&rtwpci->irq_lock, flags);

> > > > +           if (rtwpci->running) {

> > > > +                   rtw89_pci_clear_intrs(rtwdev, rtwpci);

> > >

> > > Do you really want to clear interrupts here? I'm not that familiar with

> > > the hardware here or anything, but that seems like a job for your ISR,

> > > not the NAPI poll. It also seems like you might double-clear interrupts

> > > without properly handling them, because you only called

> > > rtw89_pci_recognize_intrs() in the ISR, not here.

> >

> > This chip is an edge-trigger interrupt, so originally I'd like to make "(IMR & ISR)"

> > become 0, and then next RX packet can trigger the interrupt.

> 

> But I believe that's racy. If you clear an interrupt now based on

> rtwpci->halt_c2h_isr and rtwpci->isrs[], and later reread those fields

> in rtw89_pci_recognize_intrs(), clobbering any saved values, then you

> may lose an interrupt, I think.

> 

> Overall, the state you're keeping around, and all the interactions

> between your NAPI poll and your IRQ handler, are very complex and hard

> to reason about. I believe your rtw88 driver has a much cleaner

> interrupt dispatch logic -- it doesn't try to do smart things around

> reading/writing the interrupt mask in 3 different places (IRQ handler,

> threaded IRQ handler, and NAPI poll), but just read/stashes/clears the

> mask in one place (threadfn) and avoids saving that state globally. I

> think you might have better luck if you can imitate that. But again,

> maybe I'm missing something.

> 


I read IRQ handler of rtw88 that looks much simpler, and I picture the
new flow:

int_handler             int_threadfn              napi_poll
-----------             ------------              ---------
    |
    |
    | 1) dis. intr
    o                      |
                           | 2) read interrupt status locally
                           | 3) do TX reclaim
                           | 4) check if RX?
                           | 5) re-enable intr
                           |    (RX is optional)
                           | 6) schedule_napi
                           |    (if RX)
                           : >>>-------------------+ 7) (tasklet start immediately)
                           :                       | 
                           :                       | 8) set 'doing RX' flag
                           :                       | 9) do RX things
                           :                       | 10) clear 'doing RX' flag
                           :                       | 11) re-enable intr of RX
                           :                       |
                           : <<<-------------------o
                           :
                           o

Step 2) read and clear interrupt status with spin_lock_irqsave, and use local
variables to save the status. Then, the status will be correct, even more
interrupts are triggered.

Step 8)/10) add a 'doing RX' flag we don't enable RX interrupt in this period, so
step 5) will not make a mistake to enable RX interrupt improperly.

I attach the patch based on v5, and these changes will be included in v6.
Further suggestions are welcome.

Thank you
--
Ping-Ke
Ping-Ke Shih July 1, 2021, 12:47 a.m. UTC | #5
> -----Original Message-----

> From: Pkshih

> Sent: Friday, June 25, 2021 6:07 PM

> To: 'Brian Norris'

> Cc: kvalo@codeaurora.org; linux-wireless@vger.kernel.org

> Subject: RE: [PATCH v4 09/19] rtw89: add pci files

> 

> 

> 

> > -----Original Message-----

> > From: Brian Norris [mailto:briannorris@chromium.org]

> > Sent: Saturday, June 19, 2021 3:13 AM

> > To: Pkshih

> > Cc: kvalo@codeaurora.org; linux-wireless@vger.kernel.org

> > Subject: Re: [PATCH v4 09/19] rtw89: add pci files

> >

> >  On Wed, Jun 16, 2021 at 1:31 AM Pkshih <pkshih@realtek.com> wrote:

> > > > -----Original Message-----

> > > > From: Brian Norris [mailto:briannorris@chromium.org]

> >

> > > > On Thu, Apr 29, 2021 at 04:01:39PM +0800, Ping-Ke Shih wrote:

> > > > > --- /dev/null

> > > > > +++ b/drivers/net/wireless/realtek/rtw89/pci.c

> > > > > +static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)

> > > > > +{

> > > > > +   struct rtw89_dev *rtwdev = dev;

> > > > > +   struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;

> > > > > +   u32 isrs[2];

> > > > > +   unsigned long flags;

> > > > > +   u32 unmask0_rx = 0;

> > > > > +

> > > > > +   isrs[0] = rtwpci->isrs[0];

> > > > > +   isrs[1] = rtwpci->isrs[1];

> >

> > By the way, I'm pretty sure you need to hold the irq_lock to safely read these.

> >

> 

> Will do it.

> 

> > ...

> >

> > > By your suggestions, I trace the flow and picture them below:

> >

> > Nice, thanks for that!

> >

> > > But, three exceptions

> > > 1. interrupt is still triggered, even we disable interrupt by step 1).

> > >    That means int_handler is executed again, but threadfn doesn't enable

> > >    interrupt yet.

> >

> > I think maybe that's what IRQF_ONESHOT is for? Do you need to use

> > that? But it might not be a complete solution.

> >

> 

> I tried IRQF_ONESHOT and it works well. But this flag is mutual exclusive with

> IRQF_SHARED that is in use.

> 

> I compare the interrupt count between these two flags, there is no significant

> difference when I running TCP/UDP TX/RX stress test. Surprisingly, interrupt

> count of using IRQF_SHARED is a little lower.

> 

> Since new flow (see below) can properly handle this case, I decide to use

> original flag IRQF_SHARED.

> 

> 

> > >    This is because interrupt event is on the way to host (I think the path is

> > >    long -- from WiFi MAC to PCI MAC to PCI bus to host).

> > >    There's race condition between disable interrupt and interrupt event.

> > >

> > >    I don't plan to fix the race condition, but make the driver handle it properly.

> > >

> > > 2. napi_poll doesn't start immediately at the step 7).

> > >    I don't trace the reason yet, but I think it's reasonable that

> > >    int_threadfn and napi_poll can be ansynchronous.

> > >    Because napi_poll can run in threaded mode as well.

> > >

> > > 3. Since int_threadfn and napi_poll are ansynchronous (similar to exception 2),

> > >    it looks like napi_poll is done before int_threadfn in some situations.

> > >

> > > I'll make the driver handle these cases in next submission (v6).

> >

> > ACK.

> >

> > > Another thing is I need to do local_bh_disable() before calling napi_schedule(),

> > > or kernel warns " NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!"

> > > I think this is because __napi_schedule() does local_irq_save(), not very sure.

> > >

> > > I investigate other drivers that use napi_schedule() also do local_bh_disable()

> > > before calling napi_schedule(), or do spin_lock_bh(), or in bh context. I think

> > > these are equivalent.

> >

> > OK. I'll admit I'm not that familiar with the locking and context

> > expectations of NAPI APIs (and, they are basically undocumented), but

> > that sounds OK. I was mostly concerned that you were trying to use

> > BH-disable as a mutual exclusion mechanism, when that's not really

> > what it does.

> >

> > > > > +           spin_lock_irqsave(&rtwpci->irq_lock, flags);

> > > > > +           if (rtwpci->running) {

> > > > > +                   rtw89_pci_clear_intrs(rtwdev, rtwpci);

> > > >

> > > > Do you really want to clear interrupts here? I'm not that familiar with

> > > > the hardware here or anything, but that seems like a job for your ISR,

> > > > not the NAPI poll. It also seems like you might double-clear interrupts

> > > > without properly handling them, because you only called

> > > > rtw89_pci_recognize_intrs() in the ISR, not here.

> > >

> > > This chip is an edge-trigger interrupt, so originally I'd like to make "(IMR & ISR)"

> > > become 0, and then next RX packet can trigger the interrupt.

> >

> > But I believe that's racy. If you clear an interrupt now based on

> > rtwpci->halt_c2h_isr and rtwpci->isrs[], and later reread those fields

> > in rtw89_pci_recognize_intrs(), clobbering any saved values, then you

> > may lose an interrupt, I think.

> >

> > Overall, the state you're keeping around, and all the interactions

> > between your NAPI poll and your IRQ handler, are very complex and hard

> > to reason about. I believe your rtw88 driver has a much cleaner

> > interrupt dispatch logic -- it doesn't try to do smart things around

> > reading/writing the interrupt mask in 3 different places (IRQ handler,

> > threaded IRQ handler, and NAPI poll), but just read/stashes/clears the

> > mask in one place (threadfn) and avoids saving that state globally. I

> > think you might have better luck if you can imitate that. But again,

> > maybe I'm missing something.

> >

> 

> I read IRQ handler of rtw88 that looks much simpler, and I picture the

> new flow:

> 

> int_handler             int_threadfn              napi_poll

> -----------             ------------              ---------

>     |

>     |

>     | 1) dis. intr

>     o                      |

>                            | 2) read interrupt status locally

>                            | 3) do TX reclaim

>                            | 4) check if RX?

>                            | 5) re-enable intr

>                            |    (RX is optional)

>                            | 6) schedule_napi

>                            |    (if RX)

>                            : >>>-------------------+ 7) (tasklet start immediately)

>                            :                       |

>                            :                       | 8) set 'doing RX' flag

>                            :                       | 9) do RX things

>                            :                       | 10) clear 'doing RX' flag

>                            :                       | 11) re-enable intr of RX

>                            :                       |

>                            : <<<-------------------o

>                            :

>                            o

> 

> Step 2) read and clear interrupt status with spin_lock_irqsave, and use local

> variables to save the status. Then, the status will be correct, even more

> interrupts are triggered.

> 

> Step 8)/10) add a 'doing RX' flag we don't enable RX interrupt in this period, so

> step 5) will not make a mistake to enable RX interrupt improperly.

> 

> I attach the patch based on v5, and these changes will be included in v6.

> Further suggestions are welcome.

> 


Sorry, I missed the changes of pci.h, so send reference patch again.

--
Ping-Ke
Brian Norris July 19, 2021, 6:50 p.m. UTC | #6
(Late response)

On Wed, Jun 30, 2021 at 5:47 PM Pkshih <pkshih@realtek.com> wrote:
> > -----Original Message-----

> > From: Pkshih


> > I read IRQ handler of rtw88 that looks much simpler, and I picture the

> > new flow:

> >

> > int_handler             int_threadfn              napi_poll

> > -----------             ------------              ---------

> >     |

> >     |

> >     | 1) dis. intr

> >     o                      |

> >                            | 2) read interrupt status locally

> >                            | 3) do TX reclaim

> >                            | 4) check if RX?

> >                            | 5) re-enable intr

> >                            |    (RX is optional)

> >                            | 6) schedule_napi

> >                            |    (if RX)

> >                            : >>>-------------------+ 7) (tasklet start immediately)

> >                            :                       |

> >                            :                       | 8) set 'doing RX' flag

> >                            :                       | 9) do RX things

> >                            :                       | 10) clear 'doing RX' flag

> >                            :                       | 11) re-enable intr of RX

> >                            :                       |

> >                            : <<<-------------------o

> >                            :

> >                            o

> >

> > Step 2) read and clear interrupt status with spin_lock_irqsave, and use local

> > variables to save the status. Then, the status will be correct, even more

> > interrupts are triggered.

> >

> > Step 8)/10) add a 'doing RX' flag we don't enable RX interrupt in this period, so

> > step 5) will not make a mistake to enable RX interrupt improperly.


BTW, I think you might be pointing out a sort of bug with rtw88 -- a
non-RX interrupt might cause RX interrupts to get re-enabled in the
midst of what's *supposed* to be a NAPI poll. It's not a fatal
functional problem or anything, but it does mean we might get excess
RX interrupts, which can defeat the purpose of polling. I suppose the
impact of such a bug depends on how frequently we're receiving other
interrupts (say, H2C?).

> > I attach the patch based on v5, and these changes will be included in v6.

> > Further suggestions are welcome.

> >

>

> Sorry, I missed the changes of pci.h, so send reference patch again.


I haven't proven to myself that every line in there is good, but I
think the general layout is better. I'm more likely to get a closer
look+test when a v6 comes around.

Thanks,
Brian
Ping-Ke Shih July 21, 2021, 3:20 a.m. UTC | #7
> -----Original Message-----

> From: Brian Norris [mailto:briannorris@chromium.org]

> Sent: Tuesday, July 20, 2021 2:51 AM

> To: Pkshih

> Cc: kvalo@codeaurora.org; linux-wireless@vger.kernel.org

> Subject: Re: [PATCH v4 09/19] rtw89: add pci files

> 

> (Late response)

> 

> On Wed, Jun 30, 2021 at 5:47 PM Pkshih <pkshih@realtek.com> wrote:

> > > -----Original Message-----

> > > From: Pkshih

> 

> > > I read IRQ handler of rtw88 that looks much simpler, and I picture the

> > > new flow:

> > >

> > > int_handler             int_threadfn              napi_poll

> > > -----------             ------------              ---------

> > >     |

> > >     |

> > >     | 1) dis. intr

> > >     o                      |

> > >                            | 2) read interrupt status locally

> > >                            | 3) do TX reclaim

> > >                            | 4) check if RX?

> > >                            | 5) re-enable intr

> > >                            |    (RX is optional)

> > >                            | 6) schedule_napi

> > >                            |    (if RX)

> > >                            : >>>-------------------+ 7) (tasklet start immediately)

> > >                            :                       |

> > >                            :                       | 8) set 'doing RX' flag

> > >                            :                       | 9) do RX things

> > >                            :                       | 10) clear 'doing RX' flag

> > >                            :                       | 11) re-enable intr of RX

> > >                            :                       |

> > >                            : <<<-------------------o

> > >                            :

> > >                            o

> > >

> > > Step 2) read and clear interrupt status with spin_lock_irqsave, and use local

> > > variables to save the status. Then, the status will be correct, even more

> > > interrupts are triggered.

> > >

> > > Step 8)/10) add a 'doing RX' flag we don't enable RX interrupt in this period, so

> > > step 5) will not make a mistake to enable RX interrupt improperly.

> 

> BTW, I think you might be pointing out a sort of bug with rtw88 -- a

> non-RX interrupt might cause RX interrupts to get re-enabled in the

> midst of what's *supposed* to be a NAPI poll. It's not a fatal

> functional problem or anything, but it does mean we might get excess

> RX interrupts, which can defeat the purpose of polling. I suppose the

> impact of such a bug depends on how frequently we're receiving other

> interrupts (say, H2C?).


Indeed. We need to add a 'doing RX' flag to rtw88. I have another thinking,
which doesn't use this flag, to refine rtw89, and I'm working on it.
If it works well, I can apply it to rtw88.

int_handler             int_threadfn              napi_poll
-----------             ------------              ---------
    |
    |
    | 1) dis. intr
    o                      |
                           | 2) read interrupt status locally
                           | 3) do unlikely things
                           | 4) schedule_napi
                           |
                           : >>>-------------------+ 5) (tasklet start immediately)
                           :                       |
                           :                       | 6) do TX completion things
                           :                       | 7) do RX things
                           :                       | 
                           :                       | 8) re-enable intr
                           :                       |
                           : <<<-------------------o
                           :
                           o

I don't change the jobs of the int_handler. The int_thread reads interrupt status
and schedules NAPI unconditionally, because only unlikely things reside in this
function, and the TX completion and RX things are done by napi_poll.
Finally, the napi_poll re-enable interrupt after it does all things.

Things I'm worried are the latency of RX and TX completion, and extra polling IO.
The latency affects performance, so I'll measure it. Also, I'll examine time cost
of polling IO, and compare the count of polling IO before/after this change.

I hope I can finish this work before v6.

--
Ping-Ke
diff mbox series

Patch

diff --git a/drivers/net/wireless/realtek/rtw89/pci.c b/drivers/net/wireless/realtek/rtw89/pci.c
new file mode 100644
index 000000000000..5e05c7fc9d4e
--- /dev/null
+++ b/drivers/net/wireless/realtek/rtw89/pci.c
@@ -0,0 +1,2918 @@ 
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/* Copyright(c) 2020  Realtek Corporation
+ */
+
+#include <linux/pci.h>
+
+#include "mac.h"
+#include "pci.h"
+#include "reg.h"
+#include "ser.h"
+
+static bool rtw89_pci_disable_clkreq;
+static bool rtw89_pci_disable_aspm_l1;
+static bool rtw89_pci_disable_l1ss;
+module_param_named(disable_clkreq, rtw89_pci_disable_clkreq, bool, 0644);
+module_param_named(disable_aspm_l1, rtw89_pci_disable_aspm_l1, bool, 0644);
+module_param_named(disable_aspm_l1ss, rtw89_pci_disable_l1ss, bool, 0644);
+MODULE_PARM_DESC(disable_clkreq, "Set Y to disable PCI clkreq support");
+MODULE_PARM_DESC(disable_aspm_l1, "Set Y to disable PCI ASPM L1 support");
+MODULE_PARM_DESC(disable_aspm_l1ss, "Set Y to disable PCI L1SS support");
+
+static int rtw89_pci_rst_bdram_pcie(struct rtw89_dev *rtwdev)
+{
+	u32 val;
+	int ret;
+
+	rtw89_write32(rtwdev, R_AX_PCIE_INIT_CFG1,
+		      rtw89_read32(rtwdev, R_AX_PCIE_INIT_CFG1) | B_AX_RST_BDRAM);
+
+	ret = read_poll_timeout_atomic(rtw89_read32, val, !(val & B_AX_RST_BDRAM),
+				       1, RTW89_PCI_POLL_BDRAM_RST_CNT, false,
+				       rtwdev, R_AX_PCIE_INIT_CFG1);
+
+	if (ret)
+		return -EBUSY;
+
+	return 0;
+}
+
+static u32 rtw89_pci_dma_recalc(struct rtw89_dev *rtwdev,
+				struct rtw89_pci_dma_ring *bd_ring,
+				u32 cur_idx, bool tx)
+{
+	u32 cnt, cur_rp, wp, rp, len;
+
+	rp = bd_ring->rp;
+	wp = bd_ring->wp;
+	len = bd_ring->len;
+
+	cur_rp = FIELD_GET(TXBD_HW_IDX_MASK, cur_idx);
+	if (tx)
+		cnt = cur_rp >= rp ? cur_rp - rp : len - (rp - cur_rp);
+	else
+		cnt = cur_rp >= wp ? cur_rp - wp : len - (wp - cur_rp);
+
+	bd_ring->rp = cur_rp;
+
+	return cnt;
+}
+
+static u32 rtw89_pci_txbd_recalc(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 addr_idx = bd_ring->addr_idx;
+	u32 cnt, idx;
+
+	idx = rtw89_read32(rtwdev, addr_idx);
+	cnt = rtw89_pci_dma_recalc(rtwdev, bd_ring, idx, true);
+
+	return cnt;
+}
+
+static void rtw89_pci_release_fwcmd(struct rtw89_dev *rtwdev,
+				    struct rtw89_pci *rtwpci,
+				    u32 cnt)
+{
+	struct rtw89_pci_tx_data *tx_data;
+	struct sk_buff *skb;
+
+	while (cnt--) {
+		skb = skb_dequeue(&rtwpci->h2c_queue);
+		if (!skb) {
+			rtw89_err(rtwdev, "failed to release fwcmd\n");
+			return;
+		}
+
+		tx_data = RTW89_PCI_TX_SKB_CB(skb);
+		dma_unmap_single(&rtwpci->pdev->dev, tx_data->dma, skb->len,
+				 DMA_TO_DEVICE);
+		dev_kfree_skb_any(skb);
+	}
+}
+
+static void rtw89_pci_isr_txch_dma(struct rtw89_dev *rtwdev,
+				   struct rtw89_pci *rtwpci,
+				   enum rtw89_tx_channel txch)
+{
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+	u32 cnt;
+
+	if (txch != RTW89_TXCH_CH12)
+		return;
+
+	spin_lock_bh(&rtwpci->trx_lock);
+
+	cnt = rtw89_pci_txbd_recalc(rtwdev, tx_ring);
+	if (!cnt)
+		rtw89_warn(rtwdev, "No TXBD consumed after DMA kicked off\n");
+	rtw89_pci_release_fwcmd(rtwdev, rtwpci, cnt);
+
+	spin_unlock_bh(&rtwpci->trx_lock);
+}
+
+static u32 rtw89_pci_rxbd_recalc(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_rx_ring *rx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u32 addr_idx = bd_ring->addr_idx;
+	u32 cnt, idx;
+
+	idx = rtw89_read32(rtwdev, addr_idx);
+	cnt = rtw89_pci_dma_recalc(rtwdev, bd_ring, idx, false);
+
+	return cnt;
+}
+
+static void rtw89_pci_sync_skb_for_cpu(struct rtw89_dev *rtwdev,
+				       struct sk_buff *skb)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	dma_addr_t dma;
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	dma = rx_info->dma;
+	dma_sync_single_for_cpu(rtwdev->dev, dma, RTW89_PCI_RX_BUF_SIZE,
+				DMA_FROM_DEVICE);
+}
+
+static void rtw89_pci_sync_skb_for_device(struct rtw89_dev *rtwdev,
+					  struct sk_buff *skb)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	dma_addr_t dma;
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	dma = rx_info->dma;
+	dma_sync_single_for_device(rtwdev->dev, dma, RTW89_PCI_RX_BUF_SIZE,
+				   DMA_FROM_DEVICE);
+}
+
+static int rtw89_pci_rxbd_info_update(struct rtw89_dev *rtwdev,
+				      struct sk_buff *skb)
+{
+	struct rtw89_pci_rxbd_info *rxbd_info;
+	struct rtw89_pci_rx_info *rx_info = RTW89_PCI_RX_SKB_CB(skb);
+
+	rxbd_info = (struct rtw89_pci_rxbd_info *)skb->data;
+	rx_info->fs = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_FS);
+	rx_info->ls = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_LS);
+	rx_info->len = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_WRITE_SIZE);
+	rx_info->tag = le32_get_bits(rxbd_info->dword, RTW89_PCI_RXBD_TAG);
+
+	return 0;
+}
+
+static bool
+rtw89_skb_put_rx_data(struct rtw89_dev *rtwdev, bool fs, bool ls,
+		      struct sk_buff *new,
+		      const struct sk_buff *skb, u32 offset,
+		      const struct rtw89_pci_rx_info *rx_info,
+		      const struct rtw89_rx_desc_info *desc_info)
+{
+	u32 copy_len = rx_info->len - offset;
+
+	if (unlikely(skb_tailroom(new) < copy_len)) {
+		rtw89_debug(rtwdev, RTW89_DBG_TXRX,
+			    "invalid rx data length bd_len=%d desc_len=%d offset=%d (fs=%d ls=%d)\n",
+			    rx_info->len, desc_info->pkt_size, offset, fs, ls);
+		rtw89_hex_dump(rtwdev, RTW89_DBG_TXRX, "rx_data: ",
+			       skb->data, rx_info->len);
+		/* length of a single segment skb is desc_info->pkt_size */
+		if (fs && ls) {
+			copy_len = desc_info->pkt_size;
+		} else {
+			rtw89_info(rtwdev, "drop rx data due to invalid length\n");
+			return false;
+		}
+	}
+
+	skb_put_data(new, skb->data + offset, copy_len);
+
+	return true;
+}
+
+static u32 rtw89_pci_rxbd_deliver_skbs(struct rtw89_dev *rtwdev,
+				       struct rtw89_pci_rx_ring *rx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	struct rtw89_pci_rx_info *rx_info;
+	struct rtw89_rx_desc_info *desc_info = &rx_ring->diliver_desc;
+	struct sk_buff *new = rx_ring->diliver_skb;
+	struct sk_buff *skb;
+	u32 rxinfo_size = sizeof(struct rtw89_pci_rxbd_info);
+	u32 offset;
+	u32 cnt = 1;
+	bool fs, ls;
+	int ret;
+
+	skb = rx_ring->buf[bd_ring->wp];
+	rtw89_pci_sync_skb_for_cpu(rtwdev, skb);
+
+	ret = rtw89_pci_rxbd_info_update(rtwdev, skb);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to update %d RXBD info: %d\n",
+			  bd_ring->wp, ret);
+		goto err_sync_device;
+	}
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	fs = rx_info->fs;
+	ls = rx_info->ls;
+
+	if (fs) {
+		if (new) {
+			rtw89_err(rtwdev, "skb should not be ready before first segment start\n");
+			goto err_sync_device;
+		}
+		if (desc_info->ready) {
+			rtw89_warn(rtwdev, "desc info should not be ready before first segment start\n");
+			goto err_sync_device;
+		}
+
+		rtw89_core_query_rxdesc(rtwdev, desc_info, skb->data, rxinfo_size);
+
+		new = dev_alloc_skb(desc_info->pkt_size);
+		if (!new)
+			goto err_sync_device;
+
+		rx_ring->diliver_skb = new;
+
+		/* first segment has RX desc */
+		offset = desc_info->offset;
+		offset += desc_info->long_rxdesc ? sizeof(struct rtw89_rxdesc_long) :
+			  sizeof(struct rtw89_rxdesc_short);
+	} else {
+		offset = sizeof(struct rtw89_pci_rxbd_info);
+		if (!new) {
+			rtw89_warn(rtwdev, "no last skb\n");
+			goto err_sync_device;
+		}
+	}
+	if (!rtw89_skb_put_rx_data(rtwdev, fs, ls, new, skb, offset, rx_info, desc_info))
+		goto err_sync_device;
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	rtw89_pci_rxbd_increase(rx_ring, 1);
+
+	if (!desc_info->ready) {
+		rtw89_warn(rtwdev, "no rx desc information\n");
+		goto err_free_resource;
+	}
+	if (ls) {
+		rtw89_core_rx(rtwdev, desc_info, new);
+		rx_ring->diliver_skb = NULL;
+		desc_info->ready = false;
+	}
+
+	return cnt;
+
+err_sync_device:
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	rtw89_pci_rxbd_increase(rx_ring, 1);
+err_free_resource:
+	if (new)
+		dev_kfree_skb_any(new);
+	rx_ring->diliver_skb = NULL;
+	desc_info->ready = false;
+
+	return cnt;
+}
+
+static void rtw89_pci_rxbd_deliver(struct rtw89_dev *rtwdev,
+				   struct rtw89_pci_rx_ring *rx_ring,
+				   u32 cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u32 rx_cnt;
+
+	while (cnt && rtwdev->napi_budget_countdown > 0) {
+		rx_cnt = rtw89_pci_rxbd_deliver_skbs(rtwdev, rx_ring);
+		if (!rx_cnt) {
+			rtw89_err(rtwdev, "failed to deliver RXBD skb\n");
+
+			/* skip the rest RXBD bufs */
+			rtw89_pci_rxbd_increase(rx_ring, cnt);
+			break;
+		}
+
+		cnt -= rx_cnt;
+	}
+
+	rtw89_write16(rtwdev, bd_ring->addr_idx, bd_ring->wp);
+}
+
+static int rtw89_pci_poll_rxq_dma(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci, int budget)
+{
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 cnt;
+
+	rx_ring = &rtwpci->rx_rings[RTW89_RXCH_RXQ];
+
+	cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
+	if (!cnt)
+		return 0;
+
+	rtwdev->napi_budget_countdown = budget;
+	cnt = min_t(u32, budget, cnt);
+
+	rtw89_pci_rxbd_deliver(rtwdev, rx_ring, cnt);
+
+	/* In case of flushing pending SKBs, the countdown may exceed. */
+	if (rtwdev->napi_budget_countdown <= 0)
+		return budget;
+
+	return budget - rtwdev->napi_budget_countdown;
+}
+
+static void rtw89_pci_tx_status(struct rtw89_dev *rtwdev,
+				struct rtw89_pci_tx_ring *tx_ring,
+				struct sk_buff *skb, u8 tx_status)
+{
+	struct ieee80211_tx_info *info;
+
+	info = IEEE80211_SKB_CB(skb);
+	ieee80211_tx_info_clear_status(info);
+
+	if (info->flags & IEEE80211_TX_CTL_NO_ACK)
+		info->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
+	if (tx_status == RTW89_TX_DONE) {
+		info->flags |= IEEE80211_TX_STAT_ACK;
+		tx_ring->tx_acked++;
+	} else {
+		if (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)
+			rtw89_debug(rtwdev, RTW89_DBG_FW,
+				    "failed to TX of status %x\n", tx_status);
+		switch (tx_status) {
+		case RTW89_TX_RETRY_LIMIT:
+			tx_ring->tx_retry_lmt++;
+			break;
+		case RTW89_TX_LIFE_TIME:
+			tx_ring->tx_life_time++;
+			break;
+		case RTW89_TX_MACID_DROP:
+			tx_ring->tx_mac_id_drop++;
+			break;
+		default:
+			rtw89_warn(rtwdev, "invalid TX status %x\n", tx_status);
+			break;
+		}
+	}
+
+	ieee80211_tx_status_irqsafe(rtwdev->hw, skb);
+}
+
+static void rtw89_pci_reclaim_txbd(struct rtw89_dev *rtwdev, struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd *txwd;
+	u32 cnt;
+
+	cnt = rtw89_pci_txbd_recalc(rtwdev, tx_ring);
+	while (cnt--) {
+		txwd = list_first_entry_or_null(&tx_ring->busy_pages, struct rtw89_pci_tx_wd, list);
+		if (!txwd) {
+			rtw89_warn(rtwdev, "No busy txwd pages available\n");
+			break;
+		}
+
+		list_del_init(&txwd->list);
+	}
+}
+
+static void rtw89_pci_release_busy_txwd(struct rtw89_dev *rtwdev,
+					struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	int i;
+
+	for (i = 0; i < wd_ring->page_num; i++) {
+		txwd = list_first_entry_or_null(&tx_ring->busy_pages, struct rtw89_pci_tx_wd, list);
+		if (!txwd)
+			break;
+
+		list_del_init(&txwd->list);
+	}
+}
+
+static void rtw89_pci_release_txwd_skb(struct rtw89_dev *rtwdev,
+				       struct rtw89_pci_tx_ring *tx_ring,
+				       struct rtw89_pci_tx_wd *txwd, u16 seq,
+				       u8 tx_status)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_data *tx_data;
+	struct sk_buff *skb, *tmp;
+	u8 txch = tx_ring->txch;
+
+	if (!list_empty(&txwd->list)) {
+		rtw89_warn(rtwdev, "queue %d txwd %d is not idle\n",
+			   txch, seq);
+		return;
+	}
+
+	/* currently, support for only one frame */
+	if (skb_queue_len(&txwd->queue) != 1) {
+		rtw89_warn(rtwdev, "empty pending queue %d page %d\n",
+			   txch, seq);
+		return;
+	}
+
+	skb_queue_walk_safe(&txwd->queue, skb, tmp) {
+		skb_unlink(skb, &txwd->queue);
+
+		tx_data = RTW89_PCI_TX_SKB_CB(skb);
+		dma_unmap_single(&rtwpci->pdev->dev, tx_data->dma, skb->len,
+				 DMA_TO_DEVICE);
+
+		rtw89_pci_tx_status(rtwdev, tx_ring, skb, tx_status);
+	}
+
+	rtw89_pci_enqueue_txwd(tx_ring, txwd);
+}
+
+static void rtw89_pci_release_rpp(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci_rpp_fmt *rpp)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	struct rtw89_pci_tx_wd_ring *wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	u16 seq;
+	u8 qsel, tx_status, txch;
+
+	seq = le32_get_bits(rpp->dword, RTW89_PCI_RPP_SEQ);
+	qsel = le32_get_bits(rpp->dword, RTW89_PCI_RPP_QSEL);
+	tx_status = le32_get_bits(rpp->dword, RTW89_PCI_RPP_TX_STATUS);
+	txch = rtw89_core_get_ch_dma(rtwdev, qsel);
+
+	if (txch == RTW89_TXCH_CH12) {
+		rtw89_warn(rtwdev, "should no fwcmd release report\n");
+		return;
+	}
+
+	tx_ring = &rtwpci->tx_rings[txch];
+	rtw89_pci_reclaim_txbd(rtwdev, tx_ring);
+	wd_ring = &tx_ring->wd_ring;
+	txwd = &wd_ring->pages[seq];
+
+	rtw89_pci_release_txwd_skb(rtwdev, tx_ring, txwd, seq, tx_status);
+}
+
+static void rtw89_pci_release_pending_txwd_skb(struct rtw89_dev *rtwdev,
+					       struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	int i;
+
+	for (i = 0; i < wd_ring->page_num; i++) {
+		txwd = &wd_ring->pages[i];
+
+		if (!list_empty(&txwd->list))
+			continue;
+
+		rtw89_pci_release_txwd_skb(rtwdev, tx_ring, txwd, i, RTW89_TX_MACID_DROP);
+	}
+}
+
+static u32 rtw89_pci_release_tx_skbs(struct rtw89_dev *rtwdev,
+				     struct rtw89_pci_rx_ring *rx_ring,
+				     u32 max_cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	struct rtw89_pci_rx_info *rx_info;
+	struct rtw89_pci_rpp_fmt *rpp;
+	struct rtw89_rx_desc_info desc_info = {};
+	struct sk_buff *skb;
+	u32 cnt = 0;
+	u32 rpp_size = sizeof(struct rtw89_pci_rpp_fmt);
+	u32 rxinfo_size = sizeof(struct rtw89_pci_rxbd_info);
+	u32 offset;
+	int ret;
+
+	skb = rx_ring->buf[bd_ring->wp];
+	rtw89_pci_sync_skb_for_cpu(rtwdev, skb);
+
+	ret = rtw89_pci_rxbd_info_update(rtwdev, skb);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to update %d RXBD info: %d\n",
+			  bd_ring->wp, ret);
+		goto err_sync_device;
+	}
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	if (!rx_info->fs || !rx_info->ls) {
+		rtw89_err(rtwdev, "cannot process RP frame not set FS/LS\n");
+		return cnt;
+	}
+
+	rtw89_core_query_rxdesc(rtwdev, &desc_info, skb->data, rxinfo_size);
+
+	/* first segment has RX desc */
+	offset = desc_info.offset;
+	offset += desc_info.long_rxdesc ? sizeof(struct rtw89_rxdesc_long) :
+					  sizeof(struct rtw89_rxdesc_short);
+	for (; offset + rpp_size <= rx_info->len; offset += rpp_size) {
+		rpp = (struct rtw89_pci_rpp_fmt *)(skb->data + offset);
+		rtw89_pci_release_rpp(rtwdev, rpp);
+	}
+
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	rtw89_pci_rxbd_increase(rx_ring, 1);
+	cnt++;
+
+	return cnt;
+
+err_sync_device:
+	rtw89_pci_sync_skb_for_device(rtwdev, skb);
+	return 0;
+}
+
+static void rtw89_pci_release_tx(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_rx_ring *rx_ring,
+				 u32 cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u32 release_cnt;
+
+	while (cnt) {
+		release_cnt = rtw89_pci_release_tx_skbs(rtwdev, rx_ring, cnt);
+		if (!release_cnt) {
+			rtw89_err(rtwdev, "failed to release TX skbs\n");
+
+			/* skip the rest RXBD bufs */
+			rtw89_pci_rxbd_increase(rx_ring, cnt);
+			break;
+		}
+
+		cnt -= release_cnt;
+	}
+
+	rtw89_write16(rtwdev, bd_ring->addr_idx, bd_ring->wp);
+}
+
+static void rtw89_pci_isr_rpq_dma(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci)
+{
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 cnt;
+
+	rx_ring = &rtwpci->rx_rings[RTW89_RXCH_RPQ];
+
+	spin_lock_bh(&rtwpci->trx_lock);
+
+	cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
+	if (cnt == 0)
+		goto out_unlock;
+
+	rtw89_pci_release_tx(rtwdev, rx_ring, cnt);
+
+out_unlock:
+	spin_unlock_bh(&rtwpci->trx_lock);
+}
+
+static void rtw89_pci_isr_rxd_unavail(struct rtw89_dev *rtwdev,
+				      struct rtw89_pci *rtwpci)
+{
+	struct rtw89_pci_rx_ring *rx_ring;
+	struct rtw89_pci_dma_ring *bd_ring;
+	u32 reg_idx;
+	int i;
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		bd_ring = &rx_ring->bd_ring;
+
+		reg_idx = rtw89_read32(rtwdev, bd_ring->addr_idx);
+
+		rtw89_warn(rtwdev, "%d RXD unavailable, idx=0x%08x, len=%d\n",
+			   i, reg_idx, bd_ring->len);
+	}
+}
+
+static void rtw89_pci_clear_intrs(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci)
+{
+	rtw89_write32(rtwdev, R_AX_HISR0, rtwpci->halt_c2h_isrs);
+	rtw89_write32(rtwdev, R_AX_PCIE_HISR00, rtwpci->isrs[0]);
+	rtw89_write32(rtwdev, R_AX_PCIE_HISR10, rtwpci->isrs[1]);
+}
+
+static void rtw89_pci_recognize_intrs(struct rtw89_dev *rtwdev,
+				      struct rtw89_pci *rtwpci)
+{
+	rtwpci->halt_c2h_isrs = rtw89_read32(rtwdev, R_AX_HISR0) & rtwpci->halt_c2h_intrs;
+	rtwpci->isrs[0] = rtw89_read32(rtwdev, R_AX_PCIE_HISR00) & rtwpci->intrs[0];
+	rtwpci->isrs[1] = rtw89_read32(rtwdev, R_AX_PCIE_HISR10) & rtwpci->intrs[1];
+}
+
+static void rtw89_pci_enable_intr(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci *rtwpci)
+{
+	rtw89_write32(rtwdev, R_AX_HIMR0, rtwpci->halt_c2h_intrs);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, rtwpci->intrs[0]);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, rtwpci->intrs[1]);
+}
+
+static void rtw89_pci_enable_intr_unmask0(struct rtw89_dev *rtwdev,
+					  struct rtw89_pci *rtwpci, u32 unmask0)
+{
+	rtwpci->intrs[0] &= ~unmask0;
+	rtw89_pci_enable_intr(rtwdev, rtwpci);
+}
+
+static void rtw89_pci_enable_intr_mask0(struct rtw89_dev *rtwdev,
+					struct rtw89_pci *rtwpci, u32 mask0)
+{
+	rtwpci->intrs[0] |= mask0;
+	rtw89_pci_enable_intr(rtwdev, rtwpci);
+}
+
+static void rtw89_pci_disable_intr(struct rtw89_dev *rtwdev,
+				   struct rtw89_pci *rtwpci)
+{
+	rtw89_write32(rtwdev, R_AX_HIMR0, 0);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR00, 0);
+	rtw89_write32(rtwdev, R_AX_PCIE_HIMR10, 0);
+}
+
+static void rtw89_pci_try_napi_schedule(struct rtw89_dev *rtwdev, u32 *unmask0_rx)
+{
+	if (*unmask0_rx && !napi_reschedule(&rtwdev->napi)) {
+		/* if can't invoke napi, RX_IMR must be off already */
+		*unmask0_rx = 0;
+	}
+}
+
+static irqreturn_t rtw89_pci_interrupt_threadfn(int irq, void *dev)
+{
+	struct rtw89_dev *rtwdev = dev;
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 isrs[2];
+	unsigned long flags;
+	u32 unmask0_rx = 0;
+
+	isrs[0] = rtwpci->isrs[0];
+	isrs[1] = rtwpci->isrs[1];
+
+	/* TX ISR */
+	if (isrs[0] & B_AX_TXDMA_CH12_INT)
+		rtw89_pci_isr_txch_dma(rtwdev, rtwpci, RTW89_TXCH_CH12);
+
+	/* RX ISR */
+	if (isrs[0] & (B_AX_RXDMA_INT | B_AX_RXP1DMA_INT))
+		unmask0_rx = B_AX_RXDMA_INTS_MASK;
+	if (isrs[0] & B_AX_RPQDMA_INT)
+		rtw89_pci_isr_rpq_dma(rtwdev, rtwpci);
+	if (isrs[0] & B_AX_RDU_INT) {
+		rtw89_pci_isr_rxd_unavail(rtwdev, rtwpci);
+		unmask0_rx = B_AX_RXDMA_INTS_MASK;
+	}
+
+	if (rtwpci->halt_c2h_isrs & B_AX_HALT_C2H_INT_EN)
+		rtw89_ser_notify(rtwdev, rtw89_mac_get_err_status(rtwdev));
+
+	/* invoke napi and disable rx_imr within bh_disable, because we must
+	 * ensure napi_poll re-enable rx_imr after this.
+	 */
+	local_bh_disable();
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtw89_pci_try_napi_schedule(rtwdev, &unmask0_rx);
+	if (rtwpci->running) {
+		rtw89_pci_clear_intrs(rtwdev, rtwpci);
+		rtw89_pci_enable_intr_unmask0(rtwdev, rtwpci, unmask0_rx);
+	}
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+	local_bh_enable();
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t rtw89_pci_interrupt_handler(int irq, void *dev)
+{
+	struct rtw89_dev *rtwdev = dev;
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long flags;
+
+	/* Disable interrupt here to avoid more interrupts being issued before
+	 * the threadfn ends.
+	 */
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtw89_pci_disable_intr(rtwdev, rtwpci);
+	rtw89_pci_recognize_intrs(rtwdev, rtwpci);
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	return IRQ_WAKE_THREAD;
+}
+
+#define case_TXCHADDRS(txch) \
+	case RTW89_TXCH_##txch: \
+		*addr_num = R_AX_##txch##_TXBD_NUM; \
+		*addr_idx = R_AX_##txch##_TXBD_IDX; \
+		*addr_bdram = R_AX_##txch##_BDRAM_CTRL; \
+		*addr_desa_l = R_AX_##txch##_TXBD_DESA_L; \
+		*addr_desa_h = R_AX_##txch##_TXBD_DESA_H; \
+		break
+
+static int rtw89_pci_get_txch_addrs(enum rtw89_tx_channel txch,
+				    u32 *addr_num,
+				    u32 *addr_idx,
+				    u32 *addr_bdram,
+				    u32 *addr_desa_l,
+				    u32 *addr_desa_h)
+{
+	switch (txch) {
+	case_TXCHADDRS(ACH0);
+	case_TXCHADDRS(ACH1);
+	case_TXCHADDRS(ACH2);
+	case_TXCHADDRS(ACH3);
+	case_TXCHADDRS(ACH4);
+	case_TXCHADDRS(ACH5);
+	case_TXCHADDRS(ACH6);
+	case_TXCHADDRS(ACH7);
+	case_TXCHADDRS(CH8);
+	case_TXCHADDRS(CH9);
+	case_TXCHADDRS(CH10);
+	case_TXCHADDRS(CH11);
+	case_TXCHADDRS(CH12);
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+#undef case_TXCHADDRS
+
+#define case_RXCHADDRS(rxch) \
+	case RTW89_RXCH_##rxch: \
+		*addr_num = R_AX_##rxch##_RXBD_NUM; \
+		*addr_idx = R_AX_##rxch##_RXBD_IDX; \
+		*addr_desa_l = R_AX_##rxch##_RXBD_DESA_L; \
+		*addr_desa_h = R_AX_##rxch##_RXBD_DESA_H; \
+		break
+
+static int rtw89_pci_get_rxch_addrs(enum rtw89_rx_channel rxch,
+				    u32 *addr_num,
+				    u32 *addr_idx,
+				    u32 *addr_desa_l,
+				    u32 *addr_desa_h)
+{
+	switch (rxch) {
+	case_RXCHADDRS(RXQ);
+	case_RXCHADDRS(RPQ);
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+#undef case_RXCHADDRS
+
+static u32 rtw89_pci_get_avail_txbd_num(struct rtw89_pci_tx_ring *ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &ring->bd_ring;
+
+	/* reserved 1 desc check ring is full or not */
+	if (bd_ring->rp > bd_ring->wp)
+		return bd_ring->rp - bd_ring->wp - 1;
+
+	return bd_ring->len - (bd_ring->wp - bd_ring->rp) - 1;
+}
+
+static u32 rtw89_pci_check_and_reclaim_tx_resource(struct rtw89_dev *rtwdev,
+						   u8 txch)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	u32 bd_cnt, wd_cnt, min_cnt = 0;
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 cnt;
+
+	rx_ring = &rtwpci->rx_rings[RTW89_RXCH_RPQ];
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	bd_cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
+	wd_cnt = wd_ring->curr_num;
+
+	if (wd_cnt == 0 || bd_cnt == 0) {
+		cnt = rtw89_pci_rxbd_recalc(rtwdev, rx_ring);
+		if (!cnt)
+			goto out_unlock;
+		rtw89_pci_release_tx(rtwdev, rx_ring, cnt);
+	}
+
+	bd_cnt = rtw89_pci_get_avail_txbd_num(tx_ring);
+	wd_cnt = wd_ring->curr_num;
+	min_cnt = min(bd_cnt, wd_cnt);
+	if (min_cnt == 0)
+		rtw89_warn(rtwdev, "still no tx resource after reclaim\n");
+
+out_unlock:
+	spin_unlock_bh(&rtwpci->trx_lock);
+
+	return min_cnt;
+}
+
+static void __rtw89_pci_tx_kick_off(struct rtw89_dev *rtwdev, struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 host_idx, addr;
+
+	addr = bd_ring->addr_idx;
+	host_idx = bd_ring->wp;
+	rtw89_write16(rtwdev, addr, host_idx);
+}
+
+static void rtw89_pci_tx_bd_ring_update(struct rtw89_dev *rtwdev, struct rtw89_pci_tx_ring *tx_ring,
+					int n_txbd)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 host_idx, len;
+
+	len = bd_ring->len;
+	host_idx = bd_ring->wp + n_txbd;
+	host_idx = host_idx < len ? host_idx : host_idx - len;
+
+	bd_ring->wp = host_idx;
+}
+
+static void rtw89_pci_ops_tx_kick_off(struct rtw89_dev *rtwdev, u8 txch)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	__rtw89_pci_tx_kick_off(rtwdev, tx_ring);
+	spin_unlock_bh(&rtwpci->trx_lock);
+}
+
+static void __pci_flush_txch(struct rtw89_dev *rtwdev, u8 txch, bool drop)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring = &rtwpci->tx_rings[txch];
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	u32 cur_idx, cur_rp;
+	u8 i;
+
+	/* Because the time taked by the I/O is a bit dynamic, it's hard to
+	 * define a reasonable fixed total timeout to use read_poll_timeout*
+	 * helper. Instead, we can ensure a reasonable polling times, so we
+	 * just use for loop with udelay here.
+	 */
+	for (i = 0; i < 30; i++) {
+		cur_idx = rtw89_read32(rtwdev, bd_ring->addr_idx);
+		cur_rp = FIELD_GET(TXBD_HW_IDX_MASK, cur_idx);
+		if (cur_rp == bd_ring->wp)
+			return;
+
+		udelay(1);
+	}
+
+	if (!drop)
+		rtw89_info(rtwdev, "timed out to flush pci txch: %d\n", txch);
+}
+
+static void __rtw89_pci_ops_flush_txchs(struct rtw89_dev *rtwdev, u32 txchs,
+					bool drop)
+{
+	u8 i;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		/* It may be unnecessary to flush FWCMD queue. */
+		if (i == RTW89_TXCH_CH12)
+			continue;
+
+		if (txchs & BIT(i))
+			__pci_flush_txch(rtwdev, i, drop);
+	}
+}
+
+static void rtw89_pci_ops_flush_queues(struct rtw89_dev *rtwdev, u32 queues,
+				       bool drop)
+{
+	__rtw89_pci_ops_flush_txchs(rtwdev, BIT(RTW89_TXCH_NUM) - 1, drop);
+}
+
+static int rtw89_pci_txwd_submit(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_tx_ring *tx_ring,
+				 struct rtw89_pci_tx_wd *txwd,
+				 struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct rtw89_txwd_body *txwd_body;
+	struct rtw89_txwd_info *txwd_info;
+	struct rtw89_pci_tx_wp_info *txwp_info;
+	struct rtw89_pci_tx_addr_info_32 *txaddr_info;
+	struct pci_dev *pdev = rtwpci->pdev;
+	struct sk_buff *skb = tx_req->skb;
+	struct rtw89_pci_tx_data *tx_data = RTW89_PCI_TX_SKB_CB(skb);
+	bool en_wd_info = desc_info->en_wd_info;
+	u32 txwd_len;
+	u32 txwp_len;
+	u32 txaddr_info_len;
+	dma_addr_t dma;
+	int ret;
+
+	rtw89_core_fill_txdesc(rtwdev, desc_info, txwd->vaddr);
+
+	dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(&pdev->dev, dma)) {
+		rtw89_err(rtwdev, "failed to map skb dma data\n");
+		ret = -EBUSY;
+		goto err;
+	}
+
+	tx_data->dma = dma;
+
+	txaddr_info_len = sizeof(*txaddr_info);
+	txwp_len = sizeof(*txwp_info);
+	txwd_len = sizeof(*txwd_body);
+	txwd_len += en_wd_info ? sizeof(*txwd_info) : 0;
+
+	txwp_info = txwd->vaddr + txwd_len;
+	txwp_info->seq0 = cpu_to_le16(txwd->seq | RTW89_PCI_TXWP_VALID);
+	txwp_info->seq1 = 0;
+	txwp_info->seq2 = 0;
+	txwp_info->seq3 = 0;
+
+	tx_ring->tx_cnt++;
+	txaddr_info = txwd->vaddr + txwd_len + txwp_len;
+	txaddr_info->length = cpu_to_le16(skb->len);
+	txaddr_info->option = cpu_to_le16(RTW89_PCI_ADDR_MSDU_LS |
+					  RTW89_PCI_ADDR_NUM(1));
+	txaddr_info->dma = cpu_to_le32(dma);
+
+	txwd->len = txwd_len + txwp_len + txaddr_info_len;
+
+	skb_queue_tail(&txwd->queue, skb);
+
+	return 0;
+
+err:
+	return ret;
+}
+
+static int rtw89_pci_fwcmd_submit(struct rtw89_dev *rtwdev,
+				  struct rtw89_pci_tx_ring *tx_ring,
+				  struct rtw89_pci_tx_bd_32 *txbd,
+				  struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	struct rtw89_txwd_body *txwd_body;
+	struct pci_dev *pdev = rtwpci->pdev;
+	struct sk_buff *skb = tx_req->skb;
+	struct rtw89_pci_tx_data *tx_data = RTW89_PCI_TX_SKB_CB(skb);
+	dma_addr_t dma;
+
+	txwd_body = (struct rtw89_txwd_body *)skb_push(skb, sizeof(*txwd_body));
+	memset(txwd_body, 0, sizeof(*txwd_body));
+	rtw89_core_fill_txdesc(rtwdev, desc_info, txwd_body);
+
+	dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE);
+	if (dma_mapping_error(&pdev->dev, dma)) {
+		rtw89_err(rtwdev, "failed to map fwcmd dma data\n");
+		return -EBUSY;
+	}
+
+	tx_data->dma = dma;
+	txbd->option = cpu_to_le16(RTW89_PCI_TXBD_OPTION_LS);
+	txbd->length = cpu_to_le16(skb->len);
+	txbd->dma = cpu_to_le32(tx_data->dma);
+	skb_queue_tail(&rtwpci->h2c_queue, skb);
+
+	rtw89_pci_tx_bd_ring_update(rtwdev, tx_ring, 1);
+
+	return 0;
+}
+
+static int rtw89_pci_txbd_submit(struct rtw89_dev *rtwdev,
+				 struct rtw89_pci_tx_ring *tx_ring,
+				 struct rtw89_pci_tx_bd_32 *txbd,
+				 struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_pci_tx_wd *txwd;
+	int ret;
+
+	/* FWCMD queue doesn't have wd pages. Instead, it submits the CMD
+	 * buffer with WD BODY only. So here we don't need to check the free
+	 * pages of the wd ring.
+	 */
+	if (tx_ring->txch == RTW89_TXCH_CH12)
+		return rtw89_pci_fwcmd_submit(rtwdev, tx_ring, txbd, tx_req);
+
+	txwd = rtw89_pci_dequeue_txwd(tx_ring);
+	if (!txwd) {
+		rtw89_err(rtwdev, "no available TXWD\n");
+		ret = -ENOSPC;
+		goto err;
+	}
+
+	ret = rtw89_pci_txwd_submit(rtwdev, tx_ring, txwd, tx_req);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to submit TXWD %d\n", txwd->seq);
+		goto err_enqueue_wd;
+	}
+
+	list_add_tail(&txwd->list, &tx_ring->busy_pages);
+
+	txbd->option = cpu_to_le16(RTW89_PCI_TXBD_OPTION_LS);
+	txbd->length = cpu_to_le16(txwd->len);
+	txbd->dma = cpu_to_le32(txwd->paddr);
+
+	rtw89_pci_tx_bd_ring_update(rtwdev, tx_ring, 1);
+
+	return 0;
+
+err_enqueue_wd:
+	rtw89_pci_enqueue_txwd(tx_ring, txwd);
+err:
+	return ret;
+}
+
+static int rtw89_pci_tx_write(struct rtw89_dev *rtwdev, struct rtw89_core_tx_request *tx_req,
+			      u8 txch)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	struct rtw89_pci_tx_bd_32 *txbd;
+	u32 n_avail_txbd;
+	int ret = 0;
+
+	/* check the tx type and dma channel for fw cmd queue */
+	if ((txch == RTW89_TXCH_CH12 ||
+	     tx_req->tx_type == RTW89_CORE_TX_TYPE_FWCMD) &&
+	    (txch != RTW89_TXCH_CH12 ||
+	     tx_req->tx_type != RTW89_CORE_TX_TYPE_FWCMD)) {
+		rtw89_err(rtwdev, "only fw cmd uses dma channel 12\n");
+		return -EINVAL;
+	}
+
+	tx_ring = &rtwpci->tx_rings[txch];
+	spin_lock_bh(&rtwpci->trx_lock);
+
+	n_avail_txbd = rtw89_pci_get_avail_txbd_num(tx_ring);
+	if (n_avail_txbd == 0) {
+		rtw89_err(rtwdev, "no available TXBD\n");
+		ret = -ENOSPC;
+		goto err_unlock;
+	}
+
+	txbd = rtw89_pci_get_next_txbd(tx_ring);
+	ret = rtw89_pci_txbd_submit(rtwdev, tx_ring, txbd, tx_req);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to submit TXBD\n");
+		goto err_unlock;
+	}
+
+	spin_unlock_bh(&rtwpci->trx_lock);
+	return 0;
+
+err_unlock:
+	spin_unlock_bh(&rtwpci->trx_lock);
+	return ret;
+}
+
+static int rtw89_pci_ops_tx_write(struct rtw89_dev *rtwdev, struct rtw89_core_tx_request *tx_req)
+{
+	struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
+	int ret;
+
+	ret = rtw89_pci_tx_write(rtwdev, tx_req, desc_info->ch_dma);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to TX Queue %d\n", desc_info->ch_dma);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct rtw89_pci_bd_ram bd_ram_table[RTW89_TXCH_NUM] = {
+	[RTW89_TXCH_ACH0] = {.start_idx = 0,  .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH1] = {.start_idx = 5,  .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH2] = {.start_idx = 10, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH3] = {.start_idx = 15, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH4] = {.start_idx = 20, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH5] = {.start_idx = 25, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH6] = {.start_idx = 30, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_ACH7] = {.start_idx = 35, .max_num = 5, .min_num = 2},
+	[RTW89_TXCH_CH8]  = {.start_idx = 40, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH9]  = {.start_idx = 45, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH10] = {.start_idx = 50, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH11] = {.start_idx = 55, .max_num = 5, .min_num = 1},
+	[RTW89_TXCH_CH12] = {.start_idx = 60, .max_num = 4, .min_num = 1},
+};
+
+static void rtw89_pci_reset_trx_rings(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	struct rtw89_pci_rx_ring *rx_ring;
+	struct rtw89_pci_dma_ring *bd_ring;
+	const struct rtw89_pci_bd_ram *bd_ram;
+	u32 addr_num;
+	u32 addr_bdram;
+	u32 addr_desa_l;
+	u32 val32;
+	int i;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		bd_ring = &tx_ring->bd_ring;
+		bd_ram = &bd_ram_table[i];
+		addr_num = bd_ring->addr_num;
+		addr_bdram = bd_ring->addr_bdram;
+		addr_desa_l = bd_ring->addr_desa_l;
+		bd_ring->wp = 0;
+		bd_ring->rp = 0;
+
+		val32 = FIELD_PREP(BDRAM_SIDX_MASK, bd_ram->start_idx) |
+			FIELD_PREP(BDRAM_MAX_MASK, bd_ram->max_num) |
+			FIELD_PREP(BDRAM_MIN_MASK, bd_ram->min_num);
+
+		rtw89_write16(rtwdev, addr_num, bd_ring->len);
+		rtw89_write32(rtwdev, addr_bdram, val32);
+		rtw89_write32(rtwdev, addr_desa_l, bd_ring->dma);
+	}
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		bd_ring = &rx_ring->bd_ring;
+		addr_num = bd_ring->addr_num;
+		addr_desa_l = bd_ring->addr_desa_l;
+		bd_ring->wp = 0;
+		bd_ring->rp = 0;
+		rx_ring->diliver_skb = NULL;
+		rx_ring->diliver_desc.ready = false;
+
+		rtw89_write16(rtwdev, addr_num, bd_ring->len);
+		rtw89_write32(rtwdev, addr_desa_l, bd_ring->dma);
+	}
+}
+
+static void rtw89_pci_release_tx_ring(struct rtw89_dev *rtwdev,
+				      struct rtw89_pci_tx_ring *tx_ring)
+{
+	rtw89_pci_release_busy_txwd(rtwdev, tx_ring);
+	rtw89_pci_release_pending_txwd_skb(rtwdev, tx_ring);
+}
+
+static void rtw89_pci_ops_reset(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	int txch;
+
+	rtw89_pci_reset_trx_rings(rtwdev);
+
+	spin_lock_bh(&rtwpci->trx_lock);
+	for (txch = 0; txch < RTW89_TXCH_NUM; txch++) {
+		if (txch == RTW89_TXCH_CH12) {
+			rtw89_pci_release_fwcmd(rtwdev, rtwpci, rtwpci->h2c_queue.qlen);
+			continue;
+		}
+		rtw89_pci_release_tx_ring(rtwdev, &rtwpci->tx_rings[txch]);
+	}
+	spin_unlock_bh(&rtwpci->trx_lock);
+}
+
+static int rtw89_pci_ops_start(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long flags;
+
+	rtw89_core_napi_start(rtwdev);
+
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtwpci->running = true;
+	rtw89_pci_enable_intr_mask0(rtwdev, rtwpci, B_AX_RXDMA_INTS_MASK);
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	return 0;
+}
+
+static void rtw89_pci_ops_stop(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct pci_dev *pdev = rtwpci->pdev;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtwpci->irq_lock, flags);
+	rtwpci->running = false;
+	rtw89_pci_disable_intr(rtwdev, rtwpci);
+	spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+
+	synchronize_irq(pdev->irq);
+	rtw89_core_napi_stop(rtwdev);
+}
+
+static void rtw89_pci_ops_write32(struct rtw89_dev *rtwdev, u32 addr, u32 data);
+
+static u32 rtw89_pci_ops_read32_cmac(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 val = readl(rtwpci->mmap + addr);
+	int count;
+
+	for (count = 0; ; count++) {
+		if (val != RTW89_R32_DEAD)
+			return val;
+		if (count >= MAC_REG_POOL_COUNT) {
+			rtw89_warn(rtwdev, "addr 0x%x = 0xdeadbeef\n", addr);
+			return RTW89_R32_DEAD;
+		}
+		rtw89_pci_ops_write32(rtwdev, R_AX_CK_EN, B_AX_CMAC_ALLCKEN);
+		val = readl(rtwpci->mmap + addr);
+	}
+
+	return val;
+}
+
+static u8 rtw89_pci_ops_read8(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 addr32, val32, shift;
+
+	if (!ACCESS_CMAC(addr))
+		return readb(rtwpci->mmap + addr);
+
+	addr32 = addr & ~0x3;
+	shift = (addr & 0x3) * 8;
+	val32 = rtw89_pci_ops_read32_cmac(rtwdev, addr32);
+	return val32 >> shift;
+}
+
+static u16 rtw89_pci_ops_read16(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	u32 addr32, val32, shift;
+
+	if (!ACCESS_CMAC(addr))
+		return readw(rtwpci->mmap + addr);
+
+	addr32 = addr & ~0x3;
+	shift = (addr & 0x3) * 8;
+	val32 = rtw89_pci_ops_read32_cmac(rtwdev, addr32);
+	return val32 >> shift;
+}
+
+static u32 rtw89_pci_ops_read32(struct rtw89_dev *rtwdev, u32 addr)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	if (!ACCESS_CMAC(addr))
+		return readl(rtwpci->mmap + addr);
+
+	return rtw89_pci_ops_read32_cmac(rtwdev, addr);
+}
+
+static void rtw89_pci_ops_write8(struct rtw89_dev *rtwdev, u32 addr, u8 data)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	writeb(data, rtwpci->mmap + addr);
+}
+
+static void rtw89_pci_ops_write16(struct rtw89_dev *rtwdev, u32 addr, u16 data)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	writew(data, rtwpci->mmap + addr);
+}
+
+static void rtw89_pci_ops_write32(struct rtw89_dev *rtwdev, u32 addr, u32 data)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	writel(data, rtwpci->mmap + addr);
+}
+
+static void rtw89_pci_ctrl_dma_all(struct rtw89_dev *rtwdev, bool enable)
+{
+	if (enable) {
+		rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1,
+				  B_AX_TXHCI_EN | B_AX_RXHCI_EN);
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1,
+				  B_AX_STOP_PCIEIO);
+	} else {
+		rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1,
+				  B_AX_STOP_PCIEIO);
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1,
+				  B_AX_TXHCI_EN | B_AX_RXHCI_EN);
+	}
+}
+
+static int rtw89_pci_check_mdio(struct rtw89_dev *rtwdev, u8 addr, u8 speed, u16 rw_bit)
+{
+	u16 val;
+
+	rtw89_write8(rtwdev, R_AX_MDIO_CFG, addr & 0x1F);
+
+	val = rtw89_read16(rtwdev, R_AX_MDIO_CFG);
+	switch (speed) {
+	case PCIE_PHY_GEN1:
+		if (addr < 0x20)
+			val = u16_replace_bits(val, MDIO_PG0_G1, B_AX_MDIO_PHY_ADDR_MASK);
+		else
+			val = u16_replace_bits(val, MDIO_PG1_G1, B_AX_MDIO_PHY_ADDR_MASK);
+		break;
+	case PCIE_PHY_GEN2:
+		if (addr < 0x20)
+			val = u16_replace_bits(val, MDIO_PG0_G2, B_AX_MDIO_PHY_ADDR_MASK);
+		else
+			val = u16_replace_bits(val, MDIO_PG1_G2, B_AX_MDIO_PHY_ADDR_MASK);
+		break;
+	default:
+		rtw89_err(rtwdev, "[ERR]Error Speed %d!\n", speed);
+		return -EINVAL;
+	};
+	rtw89_write16(rtwdev, R_AX_MDIO_CFG, val);
+	rtw89_write16_set(rtwdev, R_AX_MDIO_CFG, rw_bit);
+
+	return read_poll_timeout(rtw89_read16, val, !(val & rw_bit), 10, 2000,
+				 false, rtwdev, R_AX_MDIO_CFG);
+}
+
+static int
+rtw89_read16_mdio(struct rtw89_dev *rtwdev, u8 addr, u8 speed, u16 *val)
+{
+	int ret;
+
+	ret = rtw89_pci_check_mdio(rtwdev, addr, speed, B_AX_MDIO_RFLAG);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]MDIO R16 0x%X fail!\n", addr);
+		return ret;
+	}
+	*val = rtw89_read16(rtwdev, R_AX_MDIO_RDATA);
+
+	return 0;
+}
+
+static int
+rtw89_write16_mdio(struct rtw89_dev *rtwdev, u8 addr, u16 data, u8 speed)
+{
+	int ret;
+
+	rtw89_write16(rtwdev, R_AX_MDIO_WDATA, data);
+	ret = rtw89_pci_check_mdio(rtwdev, addr, speed, B_AX_MDIO_WFLAG);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]MDIO W16 0x%X = %x fail!\n", addr, data);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rtw89_write16_mdio_set(struct rtw89_dev *rtwdev, u8 addr, u16 mask, u8 speed)
+{
+	int ret;
+	u16 val;
+
+	ret = rtw89_read16_mdio(rtwdev, addr, speed, &val);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, addr, val | mask, speed);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int rtw89_write16_mdio_clr(struct rtw89_dev *rtwdev, u8 addr, u16 mask, u8 speed)
+{
+	int ret;
+	u16 val;
+
+	ret = rtw89_read16_mdio(rtwdev, addr, speed, &val);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, addr, val & ~mask, speed);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int rtw89_dbi_write8(struct rtw89_dev *rtwdev, u16 addr, u8 data)
+{
+	u16 write_addr;
+	u16 remainder = addr & ~(B_AX_DBI_ADDR_MSK | B_AX_DBI_WREN_MSK);
+	u8 flag;
+	int ret;
+
+	write_addr = addr & B_AX_DBI_ADDR_MSK;
+	write_addr |= u16_encode_bits(BIT(remainder), B_AX_DBI_WREN_MSK);
+	rtw89_write8(rtwdev, R_AX_DBI_WDATA + remainder, data);
+	rtw89_write16(rtwdev, R_AX_DBI_FLAG, write_addr);
+	rtw89_write8(rtwdev, R_AX_DBI_FLAG + 2, B_AX_DBI_WFLAG >> 16);
+
+	ret = read_poll_timeout_atomic(rtw89_read8, flag, !flag, 10,
+				       10 * RTW89_PCI_WR_RETRY_CNT, false,
+				       rtwdev, R_AX_DBI_FLAG + 2);
+	if (ret)
+		WARN(flag, "failed to write to DBI register, addr=0x%04x\n",
+		     addr);
+
+	return ret;
+}
+
+static int rtw89_dbi_read8(struct rtw89_dev *rtwdev, u16 addr, u8 *value)
+{
+	u16 read_addr = addr & B_AX_DBI_ADDR_MSK;
+	u8 flag;
+	int ret;
+
+	rtw89_write16(rtwdev, R_AX_DBI_FLAG, read_addr);
+	rtw89_write8(rtwdev, R_AX_DBI_FLAG + 2, B_AX_DBI_RFLAG >> 16);
+
+	ret = read_poll_timeout_atomic(rtw89_read8, flag, !flag, 10,
+				       10 * RTW89_PCI_WR_RETRY_CNT, false,
+				       rtwdev, R_AX_DBI_FLAG + 2);
+
+	if (!ret) {
+		read_addr = R_AX_DBI_RDATA + (addr & 3);
+		*value = rtw89_read8(rtwdev, read_addr);
+	} else {
+		WARN(1, "failed to read DBI register, addr=0x%04x\n", addr);
+		ret =  -EIO;
+	}
+
+	return ret;
+}
+
+static int
+__get_target(struct rtw89_dev *rtwdev, u16 *target, enum rtw89_pcie_phy phy_rate)
+{
+	u16 val, tar;
+	int ret;
+
+	/* Enable counter */
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val & ~BIT(12),
+				 phy_rate);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val | BIT(12),
+				 phy_rate);
+	if (ret)
+		return ret;
+
+	fsleep(300);
+
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &tar);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val & ~BIT(12),
+				 phy_rate);
+	if (ret)
+		return ret;
+
+	tar = tar & 0x0FFF;
+	if (tar == 0 || tar == 0x0FFF) {
+		rtw89_err(rtwdev, "[ERR]Get target failed.\n");
+		return -EINVAL;
+	}
+
+	*target = tar;
+
+	return 0;
+}
+
+static int rtw89_pci_auto_refclk_cal(struct rtw89_dev *rtwdev, bool autook_en)
+{
+	enum rtw89_pcie_phy phy_rate;
+	u16 val16, mgn_set, div_set, tar;
+	u8 val8, bdr_ori;
+	bool l1_flag = false;
+	int ret = 0;
+
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_PHY_RATE, &val8);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]dbi_r8_pcie %X\n", RTW89_PCIE_PHY_RATE);
+		return ret;
+	}
+
+	if (FIELD_GET(GENMASK(1, 0), val8) == 0x1) {
+		phy_rate = PCIE_PHY_GEN1;
+	} else if (FIELD_GET(GENMASK(1, 0), val8) == 0x2) {
+		phy_rate = PCIE_PHY_GEN2;
+	} else {
+		rtw89_err(rtwdev, "[ERR]PCIe PHY rate not support\n");
+		return -EOPNOTSUPP;
+	}
+	/* Disable L1BD */
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_L1_CTRL, &bdr_ori);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]dbi_r8_pcie %X\n", RTW89_PCIE_L1_CTRL);
+		return ret;
+	}
+
+	if (bdr_ori & RTW89_PCIE_BIT_L1) {
+		ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_L1_CTRL,
+				       bdr_ori & ~RTW89_PCIE_BIT_L1);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]dbi_w8_pcie %X\n", RTW89_PCIE_L1_CTRL);
+			return ret;
+		}
+		l1_flag = true;
+	}
+
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val16);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_r16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	if (val16 & BIT(13)) {
+		ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1,
+					 val16 & ~BIT(13), phy_rate);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+			goto end;
+		}
+	}
+
+	if (!autook_en)
+		goto end;
+	/* Set div */
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_CTRL_PPR_V1, BIT(15) | BIT(14), phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	/*  Obtain div and margin */
+	ret = __get_target(rtwdev, &tar, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]1st get target fail %d\n", ret);
+		goto end;
+	}
+
+	mgn_set = tar * INTF_INTGRA_HOSTREF_V1 / INTF_INTGRA_MINREF_V1 - tar;
+
+	if (mgn_set >= 128) {
+		div_set = 0x0003;
+		mgn_set = 0x000F;
+	} else if (mgn_set >= 64) {
+		div_set = 0x0003;
+		mgn_set >>= 3;
+	} else if (mgn_set >= 32) {
+		div_set = 0x0002;
+		mgn_set >>= 2;
+	} else if (mgn_set >= 16) {
+		div_set = 0x0001;
+		mgn_set >>= 1;
+	} else if (mgn_set == 0) {
+		rtw89_err(rtwdev, "[ERR]cal mgn is 0,tar = %d\n", tar);
+		goto end;
+	} else {
+		div_set = 0x0000;
+	}
+
+	ret = rtw89_read16_mdio(rtwdev, RAC_CTRL_PPR_V1, phy_rate, &val16);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_r16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	val16 |= u16_encode_bits(div_set, GENMASK(15, 14));
+
+	ret = rtw89_write16_mdio(rtwdev, RAC_CTRL_PPR_V1, val16, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	ret = __get_target(rtwdev, &tar, phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]2nd get target fail %d\n", ret);
+		goto end;
+	}
+
+	rtw89_debug(rtwdev, RTW89_DBG_HCI, "[TRACE]target = 0x%X, div = 0x%X, margin = 0x%X\n",
+		    tar, div_set, mgn_set);
+	ret = rtw89_write16_mdio(rtwdev, RAC_SET_PPR_V1,
+				 (tar & 0x0FFF) | (mgn_set << 12), phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_SET_PPR_V1);
+		goto end;
+	}
+
+	/* Enable function */
+	ret = rtw89_write16_mdio_set(rtwdev, RAC_CTRL_PPR_V1, BIT(13), phy_rate);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR]mdio_w16_pcie %X\n", RAC_CTRL_PPR_V1);
+		goto end;
+	}
+
+	/* CLK delay = 0 */
+	ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_CLK_CTRL, PCIE_CLKDLY_HW_0);
+
+end:
+	/* Set L1BD to ori */
+	if (l1_flag) {
+		ret = rtw89_dbi_write8(rtwdev, RTW89_PCIE_L1_CTRL, bdr_ori);
+		if (ret) {
+			rtw89_err(rtwdev, "[ERR]dbi_w8_pcie %X\n", RTW89_PCIE_L1_CTRL);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_deglitch_setting(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	if (rtwdev->chip->chip_id != RTL8852A)
+		return 0;
+
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA24, GENMASK(11, 8),
+				     PCIE_PHY_GEN1);
+	if (ret)
+		return ret;
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA24, GENMASK(11, 8),
+				     PCIE_PHY_GEN2);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void rtw89_pci_rxdma_prefth(struct rtw89_dev *rtwdev)
+{
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_DIS_RXDMA_PRE);
+}
+
+static void rtw89_pci_l1off_pwroff(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_PS_CTRL, B_AX_L1OFF_PWR_OFF_EN);
+}
+
+static u32 rtw89_pci_l2_rxen_lat(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return 0;
+
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA26, GENMASK(15, 14),
+				     PCIE_PHY_GEN1);
+	if (ret)
+		return ret;
+
+	ret = rtw89_write16_mdio_clr(rtwdev, RAC_ANA26, GENMASK(11, 8),
+				     PCIE_PHY_GEN1);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void rtw89_pci_aphy_pwrcut(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id != RTL8852A)
+		return;
+
+	rtw89_write32_clr(rtwdev, R_AX_SYS_PW_CTRL, B_AX_PSUS_OFF_CAPC_EN);
+}
+
+static void rtw89_pci_hci_ldo(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id != RTL8852A)
+		return;
+
+	rtw89_write32_set(rtwdev, R_AX_SYS_SDIO_CTRL,
+			  B_AX_PCIE_DIS_L2_CTRL_LDO_HCI);
+	rtw89_write32_clr(rtwdev, R_AX_SYS_SDIO_CTRL,
+			  B_AX_PCIE_DIS_WLSUS_AFT_PDN);
+}
+
+static void rtw89_pci_set_sic(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_EXP_CTRL,
+			  B_AX_SIC_EN_FORCE_CLKREQ);
+}
+
+static void rtw89_pci_set_dbg(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852C)
+		return;
+
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DBG_CTRL,
+			  B_AX_ASFF_FULL_NO_STK | B_AX_EN_STUCK_DBG);
+
+	if (rtwdev->chip->chip_id == RTL8852A)
+		rtw89_write32_set(rtwdev, R_AX_PCIE_EXP_CTRL,
+				  B_AX_EN_CHKDSC_NO_RX_STUCK);
+}
+
+static void rtw89_pci_clr_idx_all(struct rtw89_dev *rtwdev)
+{
+	u32 val = B_AX_CLR_ACH0_IDX | B_AX_CLR_ACH1_IDX | B_AX_CLR_ACH2_IDX |
+		  B_AX_CLR_ACH3_IDX | B_AX_CLR_CH8_IDX | B_AX_CLR_CH9_IDX |
+		  B_AX_CLR_CH12_IDX;
+
+	if (rtwdev->chip->chip_id == RTL8852A)
+		val |= B_AX_CLR_ACH4_IDX | B_AX_CLR_ACH5_IDX |
+		       B_AX_CLR_ACH6_IDX | B_AX_CLR_ACH7_IDX;
+	/* clear DMA indexes */
+	rtw89_write32_set(rtwdev, R_AX_TXBD_RWPTR_CLR1, val);
+	if (rtwdev->chip->chip_id == RTL8852A)
+		rtw89_write32_set(rtwdev, R_AX_TXBD_RWPTR_CLR2,
+				  B_AX_CLR_CH10_IDX | B_AX_CLR_CH11_IDX);
+	rtw89_write32_set(rtwdev, R_AX_RXBD_RWPTR_CLR,
+			  B_AX_CLR_RXQ_IDX | B_AX_CLR_RPQ_IDX);
+}
+
+static int rtw89_pci_ops_deinit(struct rtw89_dev *rtwdev)
+{
+	if (rtwdev->chip->chip_id == RTL8852A) {
+		/* ltr sw trigger */
+		rtw89_write32_set(rtwdev, R_AX_LTR_CTRL_0, B_AX_APP_LTR_IDLE);
+	}
+	rtw89_pci_ctrl_dma_all(rtwdev, false);
+	rtw89_pci_clr_idx_all(rtwdev);
+
+	return 0;
+}
+
+static int rtw89_pci_ops_mac_pre_init(struct rtw89_dev *rtwdev)
+{
+	u32 dma_busy;
+	u32 check;
+	u32 lbc;
+	int ret;
+
+	rtw89_pci_rxdma_prefth(rtwdev);
+	rtw89_pci_l1off_pwroff(rtwdev);
+	rtw89_pci_deglitch_setting(rtwdev);
+	ret = rtw89_pci_l2_rxen_lat(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] pcie l2 rxen lat %d\n", ret);
+		return ret;
+	}
+
+	rtw89_pci_aphy_pwrcut(rtwdev);
+	rtw89_pci_hci_ldo(rtwdev);
+
+	ret = rtw89_pci_auto_refclk_cal(rtwdev, false);
+	if (ret) {
+		rtw89_err(rtwdev, "[ERR] pcie autok fail %d\n", ret);
+		return ret;
+	}
+
+	rtw89_pci_set_sic(rtwdev);
+	rtw89_pci_set_dbg(rtwdev);
+
+	if (rtwdev->chip->chip_id == RTL8852A)
+		rtw89_write32_clr(rtwdev, R_AX_SYS_SDIO_CTRL,
+				  B_AX_PCIE_AUXCLK_GATE);
+
+	lbc = rtw89_read32(rtwdev, R_AX_LBC_WATCHDOG);
+	lbc = u32_replace_bits(lbc, RTW89_MAC_LBC_TMR_2MS, B_AX_LBC_TIMER);
+	lbc |= B_AX_LBC_FLAG | B_AX_LBC_EN;
+	rtw89_write32(rtwdev, R_AX_LBC_WATCHDOG, lbc);
+
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1,
+			  B_AX_PCIE_TXRST_KEEP_REG | B_AX_PCIE_RXRST_KEEP_REG);
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_STOP_WPDMA);
+
+	/* stop DMA activities */
+	rtw89_pci_ctrl_dma_all(rtwdev, false);
+
+	/* check PCI at idle state */
+	check = B_AX_PCIEIO_BUSY | B_AX_PCIEIO_TX_BUSY | B_AX_PCIEIO_RX_BUSY;
+	ret = read_poll_timeout(rtw89_read32, dma_busy, (dma_busy & check) == 0,
+				100, 3000, false, rtwdev, R_AX_PCIE_DMA_BUSY1);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to poll io busy\n");
+		return ret;
+	}
+
+	rtw89_pci_clr_idx_all(rtwdev);
+
+	/* configure TX/RX op modes */
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_TX_TRUNC_MODE |
+						       B_AX_RX_TRUNC_MODE);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_RXBD_MODE);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_PCIE_MAX_TXDMA_MASK, 7);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_PCIE_MAX_RXDMA_MASK, 3);
+	/* multi-tag mode */
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, B_AX_LATENCY_CONTROL);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_EXP_CTRL, B_AX_MAX_TAG_NUM,
+			   RTW89_MAC_TAG_NUM_8);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG2, B_AX_WD_ITVL_IDLE,
+			   RTW89_MAC_WD_DMA_INTVL_256NS);
+	rtw89_write32_mask(rtwdev, R_AX_PCIE_INIT_CFG2, B_AX_WD_ITVL_ACT,
+			   RTW89_MAC_WD_DMA_INTVL_256NS);
+
+	/* fill TRX BD indexes */
+	rtw89_pci_reset_trx_rings(rtwdev);
+
+	ret = rtw89_pci_rst_bdram_pcie(rtwdev);
+	if (ret) {
+		rtw89_warn(rtwdev, "reset bdram busy\n");
+		return ret;
+	}
+
+	/* enable FW CMD queue to download firmware */
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_TX_STOP1_ALL);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_STOP_CH12);
+	rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP2, B_AX_TX_STOP2_ALL);
+
+	/* start DMA activities */
+	rtw89_pci_ctrl_dma_all(rtwdev, true);
+
+	return 0;
+}
+
+static int rtw89_pci_ltr_set(struct rtw89_dev *rtwdev)
+{
+	u32 val;
+
+	val = rtw89_read32(rtwdev, R_AX_LTR_CTRL_0);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+	val = rtw89_read32(rtwdev, R_AX_LTR_CTRL_1);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+	val = rtw89_read32(rtwdev, R_AX_LTR_IDLE_LATENCY);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+	val = rtw89_read32(rtwdev, R_AX_LTR_ACTIVE_LATENCY);
+	if (rtw89_pci_ltr_is_err_reg_val(val))
+		return -EINVAL;
+
+	rtw89_write32_clr(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_HW_EN);
+	rtw89_write32_set(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_EN);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_SPACE_IDX_MASK,
+			   PCI_LTR_SPC_500US);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_0, B_AX_LTR_IDLE_TIMER_IDX_MASK,
+			   PCI_LTR_IDLE_TIMER_800US);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_1, B_AX_LTR_RX0_TH_MASK, 0x28);
+	rtw89_write32_mask(rtwdev, R_AX_LTR_CTRL_1, B_AX_LTR_RX1_TH_MASK, 0x28);
+	rtw89_write32(rtwdev, R_AX_LTR_IDLE_LATENCY, 0x88e088e0);
+	rtw89_write32(rtwdev, R_AX_LTR_ACTIVE_LATENCY, 0x880b880b);
+
+	return 0;
+}
+
+static int rtw89_pci_ops_mac_post_init(struct rtw89_dev *rtwdev)
+{
+	int ret;
+
+	ret = rtw89_pci_ltr_set(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "pci ltr set fail\n");
+		return ret;
+	}
+	if (rtwdev->chip->chip_id == RTL8852A) {
+		/* ltr sw trigger */
+		rtw89_write32_set(rtwdev, R_AX_LTR_CTRL_0, B_AX_APP_LTR_ACT);
+	}
+	/* ADDR info 8-byte mode */
+	rtw89_write32_set(rtwdev, R_AX_TX_ADDRESS_INFO_MODE_SETTING,
+			  B_AX_HOST_ADDR_INFO_8B_SEL);
+	rtw89_write32_clr(rtwdev, R_AX_PKTIN_SETTING, B_AX_WD_ADDR_INFO_LENGTH);
+
+	/* enable DMA for all queues */
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1, B_AX_TX_STOP1_ALL);
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP2, B_AX_TX_STOP2_ALL);
+
+	/* Release PCI IO */
+	rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1,
+			  B_AX_STOP_WPDMA | B_AX_STOP_PCIEIO);
+
+	return 0;
+}
+
+static int rtw89_pci_claim_device(struct rtw89_dev *rtwdev,
+				  struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	int ret;
+
+	ret = pci_enable_device(pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to enable pci device\n");
+		return ret;
+	}
+
+	pci_set_master(pdev);
+	pci_set_drvdata(pdev, rtwdev->hw);
+
+	rtwpci->pdev = pdev;
+
+	return 0;
+}
+
+static void rtw89_pci_declaim_device(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	pci_clear_master(pdev);
+	pci_disable_device(pdev);
+}
+
+static int rtw89_pci_setup_mapping(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long resource_len;
+	u8 bar_id = 2;
+	int ret;
+
+	ret = pci_request_regions(pdev, KBUILD_MODNAME);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to request pci regions\n");
+		goto err;
+	}
+
+	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		rtw89_err(rtwdev, "failed to set dma mask to 32-bit\n");
+		goto err_release_regions;
+	}
+
+	ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		rtw89_err(rtwdev, "failed to set consistent dma mask to 32-bit\n");
+		goto err_release_regions;
+	}
+
+	resource_len = pci_resource_len(pdev, bar_id);
+	rtwpci->mmap = pci_iomap(pdev, bar_id, resource_len);
+	if (!rtwpci->mmap) {
+		rtw89_err(rtwdev, "failed to map pci io\n");
+		ret = -EIO;
+		goto err_release_regions;
+	}
+
+	return 0;
+
+err_release_regions:
+	pci_release_regions(pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_clear_mapping(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	if (rtwpci->mmap) {
+		pci_iounmap(pdev, rtwpci->mmap);
+		pci_release_regions(pdev);
+	}
+}
+
+static void rtw89_pci_free_tx_wd_ring(struct rtw89_dev *rtwdev,
+				      struct pci_dev *pdev,
+				      struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	u8 *head = wd_ring->head;
+	dma_addr_t dma = wd_ring->dma;
+	u32 page_size = wd_ring->page_size;
+	u32 page_num = wd_ring->page_num;
+	u32 ring_sz = page_size * page_num;
+
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+	wd_ring->head = NULL;
+}
+
+static void rtw89_pci_free_tx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_tx_ring *tx_ring)
+{
+	int ring_sz;
+	u8 *head;
+	dma_addr_t dma;
+
+	head = tx_ring->bd_ring.head;
+	dma = tx_ring->bd_ring.dma;
+	ring_sz = tx_ring->bd_ring.desc_size * tx_ring->bd_ring.len;
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+
+	tx_ring->bd_ring.head = NULL;
+}
+
+static void rtw89_pci_free_tx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	int i;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		rtw89_pci_free_tx_wd_ring(rtwdev, pdev, tx_ring);
+		rtw89_pci_free_tx_ring(rtwdev, pdev, tx_ring);
+	}
+}
+
+static void rtw89_pci_free_rx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_rx_ring *rx_ring)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	struct sk_buff *skb;
+	dma_addr_t dma;
+	u32 buf_sz;
+	u8 *head;
+	int ring_sz = rx_ring->bd_ring.desc_size * rx_ring->bd_ring.len;
+	int i;
+
+	buf_sz = rx_ring->buf_sz;
+	for (i = 0; i < rx_ring->bd_ring.len; i++) {
+		skb = rx_ring->buf[i];
+		if (!skb)
+			continue;
+
+		rx_info = RTW89_PCI_RX_SKB_CB(skb);
+		dma = rx_info->dma;
+		dma_unmap_single(&pdev->dev, dma, buf_sz, DMA_FROM_DEVICE);
+		dev_kfree_skb(skb);
+		rx_ring->buf[i] = NULL;
+	}
+
+	head = rx_ring->bd_ring.head;
+	dma = rx_ring->bd_ring.dma;
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+
+	rx_ring->bd_ring.head = NULL;
+}
+
+static void rtw89_pci_free_rx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_rx_ring *rx_ring;
+	int i;
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		rtw89_pci_free_rx_ring(rtwdev, pdev, rx_ring);
+	}
+}
+
+static void rtw89_pci_free_trx_rings(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	rtw89_pci_free_rx_rings(rtwdev, pdev);
+	rtw89_pci_free_tx_rings(rtwdev, pdev);
+}
+
+static int rtw89_pci_init_rx_bd(struct rtw89_dev *rtwdev, struct pci_dev *pdev,
+				struct rtw89_pci_rx_ring *rx_ring,
+				struct sk_buff *skb, int buf_sz, u32 idx)
+{
+	struct rtw89_pci_rx_info *rx_info;
+	struct rtw89_pci_rx_bd_32 *rx_bd;
+	dma_addr_t dma;
+
+	if (!skb)
+		return -EINVAL;
+
+	dma = dma_map_single(&pdev->dev, skb->data, buf_sz, DMA_FROM_DEVICE);
+	if (dma_mapping_error(&pdev->dev, dma))
+		return -EBUSY;
+
+	rx_info = RTW89_PCI_RX_SKB_CB(skb);
+	rx_bd = RTW89_PCI_RX_BD(rx_ring, idx);
+
+	memset(rx_bd, 0, sizeof(*rx_bd));
+	rx_bd->buf_size = cpu_to_le16(buf_sz);
+	rx_bd->dma = cpu_to_le32(dma);
+	rx_info->dma = dma;
+
+	return 0;
+}
+
+static int rtw89_pci_alloc_tx_wd_ring(struct rtw89_dev *rtwdev,
+				      struct pci_dev *pdev,
+				      struct rtw89_pci_tx_ring *tx_ring,
+				      enum rtw89_tx_channel txch)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+	dma_addr_t dma;
+	dma_addr_t cur_paddr;
+	u8 *head;
+	u8 *cur_vaddr;
+	u32 page_size = RTW89_PCI_TXWD_PAGE_SIZE;
+	u32 page_num = RTW89_PCI_TXWD_NUM_MAX;
+	u32 ring_sz = page_size * page_num;
+	u32 page_offset;
+	int i;
+
+	/* FWCMD queue doesn't use txwd as pages */
+	if (txch == RTW89_TXCH_CH12)
+		return 0;
+
+	head = dma_alloc_coherent(&pdev->dev, ring_sz, &dma, GFP_KERNEL);
+	if (!head)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&wd_ring->free_pages);
+	wd_ring->head = head;
+	wd_ring->dma = dma;
+	wd_ring->page_size = page_size;
+	wd_ring->page_num = page_num;
+
+	page_offset = 0;
+	for (i = 0; i < page_num; i++) {
+		txwd = &wd_ring->pages[i];
+		cur_paddr = dma + page_offset;
+		cur_vaddr = head + page_offset;
+
+		skb_queue_head_init(&txwd->queue);
+		INIT_LIST_HEAD(&txwd->list);
+		txwd->paddr = cur_paddr;
+		txwd->vaddr = cur_vaddr;
+		txwd->len = page_size;
+		txwd->seq = i;
+		rtw89_pci_enqueue_txwd(tx_ring, txwd);
+
+		page_offset += page_size;
+	}
+
+	return 0;
+}
+
+static int rtw89_pci_alloc_tx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_tx_ring *tx_ring,
+				   u32 desc_size, u32 len,
+				   enum rtw89_tx_channel txch)
+{
+	int ring_sz = desc_size * len;
+	u8 *head;
+	dma_addr_t dma;
+	u32 addr_num;
+	u32 addr_idx;
+	u32 addr_bdram;
+	u32 addr_desa_l;
+	u32 addr_desa_h;
+	int ret;
+
+	ret = rtw89_pci_alloc_tx_wd_ring(rtwdev, pdev, tx_ring, txch);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc txwd ring of txch %d\n", txch);
+		goto err;
+	}
+
+	ret = rtw89_pci_get_txch_addrs(txch, &addr_num, &addr_idx, &addr_bdram,
+				       &addr_desa_l, &addr_desa_h);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get address of txch %d", txch);
+		goto err_free_wd_ring;
+	}
+
+	head = dma_alloc_coherent(&pdev->dev, ring_sz, &dma, GFP_KERNEL);
+	if (!head) {
+		ret = -ENOMEM;
+		goto err_free_wd_ring;
+	}
+
+	INIT_LIST_HEAD(&tx_ring->busy_pages);
+	tx_ring->bd_ring.head = head;
+	tx_ring->bd_ring.dma = dma;
+	tx_ring->bd_ring.len = len;
+	tx_ring->bd_ring.desc_size = desc_size;
+	tx_ring->bd_ring.addr_num = addr_num;
+	tx_ring->bd_ring.addr_idx = addr_idx;
+	tx_ring->bd_ring.addr_bdram = addr_bdram;
+	tx_ring->bd_ring.addr_desa_l = addr_desa_l;
+	tx_ring->bd_ring.addr_desa_h = addr_desa_h;
+	tx_ring->bd_ring.wp = 0;
+	tx_ring->bd_ring.rp = 0;
+	tx_ring->txch = txch;
+
+	return 0;
+
+err_free_wd_ring:
+	rtw89_pci_free_tx_wd_ring(rtwdev, pdev, tx_ring);
+err:
+	return ret;
+}
+
+static int rtw89_pci_alloc_tx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_tx_ring *tx_ring;
+	u32 desc_size;
+	u32 len;
+	u32 i, tx_allocated;
+	int ret;
+
+	for (i = 0; i < RTW89_TXCH_NUM; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		desc_size = sizeof(struct rtw89_pci_tx_bd_32);
+		len = RTW89_PCI_TXBD_NUM_MAX;
+		ret = rtw89_pci_alloc_tx_ring(rtwdev, pdev, tx_ring,
+					      desc_size, len, i);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to alloc tx ring %d\n", i);
+			goto err_free;
+		}
+	}
+
+	return 0;
+
+err_free:
+	tx_allocated = i;
+	for (i = 0; i < tx_allocated; i++) {
+		tx_ring = &rtwpci->tx_rings[i];
+		rtw89_pci_free_tx_ring(rtwdev, pdev, tx_ring);
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_alloc_rx_ring(struct rtw89_dev *rtwdev,
+				   struct pci_dev *pdev,
+				   struct rtw89_pci_rx_ring *rx_ring,
+				   u32 desc_size, u32 len, u32 rxch)
+{
+	struct sk_buff *skb;
+	u8 *head;
+	dma_addr_t dma;
+	u32 addr_num;
+	u32 addr_idx;
+	u32 addr_desa_l;
+	u32 addr_desa_h;
+	int ring_sz = desc_size * len;
+	int buf_sz = RTW89_PCI_RX_BUF_SIZE;
+	int i, allocated;
+	int ret;
+
+	ret = rtw89_pci_get_rxch_addrs(rxch, &addr_num, &addr_idx,
+				       &addr_desa_l, &addr_desa_h);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to get address of rxch %d", rxch);
+		return ret;
+	}
+
+	head = dma_alloc_coherent(&pdev->dev, ring_sz, &dma, GFP_KERNEL);
+	if (!head) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	rx_ring->bd_ring.head = head;
+	rx_ring->bd_ring.dma = dma;
+	rx_ring->bd_ring.len = len;
+	rx_ring->bd_ring.desc_size = desc_size;
+	rx_ring->bd_ring.addr_num = addr_num;
+	rx_ring->bd_ring.addr_idx = addr_idx;
+	rx_ring->bd_ring.addr_desa_l = addr_desa_l;
+	rx_ring->bd_ring.addr_desa_h = addr_desa_h;
+	rx_ring->bd_ring.wp = 0;
+	rx_ring->bd_ring.rp = 0;
+	rx_ring->buf_sz = buf_sz;
+	rx_ring->diliver_skb = NULL;
+	rx_ring->diliver_desc.ready = false;
+
+	for (i = 0; i < len; i++) {
+		skb = dev_alloc_skb(buf_sz);
+		if (!skb) {
+			ret = -ENOMEM;
+			goto err_free;
+		}
+
+		memset(skb->data, 0, buf_sz);
+		rx_ring->buf[i] = skb;
+		ret = rtw89_pci_init_rx_bd(rtwdev, pdev, rx_ring, skb,
+					   buf_sz, i);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to init rx buf %d\n", i);
+			dev_kfree_skb_any(skb);
+			rx_ring->buf[i] = NULL;
+			goto err_free;
+		}
+	}
+
+	return 0;
+
+err_free:
+	allocated = i;
+	for (i = 0; i < allocated; i++) {
+		skb = rx_ring->buf[i];
+		if (!skb)
+			continue;
+		dma = *((dma_addr_t *)skb->cb);
+		dma_unmap_single(&pdev->dev, dma, buf_sz, DMA_FROM_DEVICE);
+		dev_kfree_skb(skb);
+		rx_ring->buf[i] = NULL;
+	}
+
+	head = rx_ring->bd_ring.head;
+	dma = rx_ring->bd_ring.dma;
+	dma_free_coherent(&pdev->dev, ring_sz, head, dma);
+
+	rx_ring->bd_ring.head = NULL;
+err:
+	return ret;
+}
+
+static int rtw89_pci_alloc_rx_rings(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct rtw89_pci_rx_ring *rx_ring;
+	u32 desc_size;
+	u32 len;
+	int i, rx_allocated;
+	int ret;
+
+	for (i = 0; i < RTW89_RXCH_NUM; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		desc_size = sizeof(struct rtw89_pci_rx_bd_32);
+		len = RTW89_PCI_RXBD_NUM_MAX;
+		ret = rtw89_pci_alloc_rx_ring(rtwdev, pdev, rx_ring,
+					      desc_size, len, i);
+		if (ret) {
+			rtw89_err(rtwdev, "failed to alloc rx ring %d\n", i);
+			goto err_free;
+		}
+	}
+
+	return 0;
+
+err_free:
+	rx_allocated = i;
+	for (i = 0; i < rx_allocated; i++) {
+		rx_ring = &rtwpci->rx_rings[i];
+		rtw89_pci_free_rx_ring(rtwdev, pdev, rx_ring);
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_alloc_trx_rings(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	int ret;
+
+	ret = rtw89_pci_alloc_tx_rings(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc dma tx rings\n");
+		goto err;
+	}
+
+	ret = rtw89_pci_alloc_rx_rings(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc dma rx rings\n");
+		goto err_free_tx_rings;
+	}
+
+	return 0;
+
+err_free_tx_rings:
+	rtw89_pci_free_tx_rings(rtwdev, pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_h2c_init(struct rtw89_dev *rtwdev,
+			       struct rtw89_pci *rtwpci)
+{
+	skb_queue_head_init(&rtwpci->h2c_queue);
+}
+
+static int rtw89_pci_setup_resource(struct rtw89_dev *rtwdev,
+				    struct pci_dev *pdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	int ret;
+
+	ret = rtw89_pci_setup_mapping(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to setup pci mapping\n");
+		goto err;
+	}
+
+	ret = rtw89_pci_alloc_trx_rings(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to alloc pci trx rings\n");
+		goto err_pci_unmap;
+	}
+
+	rtw89_pci_h2c_init(rtwdev, rtwpci);
+
+	spin_lock_init(&rtwpci->irq_lock);
+	spin_lock_init(&rtwpci->trx_lock);
+
+	return 0;
+
+err_pci_unmap:
+	rtw89_pci_clear_mapping(rtwdev, pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_clear_resource(struct rtw89_dev *rtwdev,
+				     struct pci_dev *pdev)
+{
+	rtw89_pci_free_trx_rings(rtwdev, pdev);
+	rtw89_pci_clear_mapping(rtwdev, pdev);
+}
+
+static void rtw89_pci_default_intr_mask(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	rtwpci->halt_c2h_intrs = B_AX_HALT_C2H_INT_EN | 0;
+	rtwpci->intrs[0] = B_AX_TXDMA_CH12_INT_EN |
+			   B_AX_TXDMA_STUCK_INT_EN |
+			   B_AX_RXDMA_INT_EN |
+			   B_AX_RXP1DMA_INT_EN |
+			   B_AX_RPQDMA_INT_EN |
+			   B_AX_RXDMA_STUCK_INT_EN |
+			   B_AX_RDU_INT_EN |
+			   B_AX_RPQBD_FULL_INT_EN |
+			   B_AX_HS0ISR_IND_INT_EN;
+
+	rtwpci->intrs[1] = B_AX_HC10ISR_IND_INT_EN;
+}
+
+static int rtw89_pci_request_irq(struct rtw89_dev *rtwdev,
+				 struct pci_dev *pdev)
+{
+	unsigned long flags = 0;
+	int ret;
+
+	flags |= PCI_IRQ_LEGACY | PCI_IRQ_MSI;
+	ret = pci_alloc_irq_vectors(pdev, 1, 1, flags);
+	if (ret < 0) {
+		rtw89_err(rtwdev, "failed to alloc irq vectors, ret %d\n", ret);
+		goto err;
+	}
+
+	ret = devm_request_threaded_irq(rtwdev->dev, pdev->irq,
+					rtw89_pci_interrupt_handler,
+					rtw89_pci_interrupt_threadfn,
+					IRQF_SHARED, KBUILD_MODNAME, rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to request threaded irq\n");
+		goto err_free_vector;
+	}
+
+	rtw89_pci_default_intr_mask(rtwdev);
+
+	return 0;
+
+err_free_vector:
+	pci_free_irq_vectors(pdev);
+err:
+	return ret;
+}
+
+static void rtw89_pci_free_irq(struct rtw89_dev *rtwdev,
+			       struct pci_dev *pdev)
+{
+	devm_free_irq(rtwdev->dev, pdev->irq, rtwdev);
+	pci_free_irq_vectors(pdev);
+}
+
+static void rtw89_pci_clkreq_set(struct rtw89_dev *rtwdev, bool enable)
+{
+	u8 value;
+	int ret;
+
+	if (rtw89_pci_disable_clkreq)
+		return;
+
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_L1_CTRL, &value);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to read CLKREQ_L1, ret=%d", ret);
+		return;
+	}
+
+	if (enable)
+		value |= RTW89_PCIE_BIT_CLK;
+	else
+		value &= ~RTW89_PCIE_BIT_CLK;
+
+	rtw89_dbi_write8(rtwdev, RTW89_PCIE_L1_CTRL, value);
+}
+
+static void rtw89_pci_aspm_set(struct rtw89_dev *rtwdev, bool enable)
+{
+	u8 value;
+	int ret;
+
+	if (rtw89_pci_disable_aspm_l1)
+		return;
+
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_L1_CTRL, &value);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to read ASPM, ret=%d", ret);
+		return;
+	}
+
+	if (enable)
+		value |= RTW89_PCIE_BIT_L1;
+	else
+		value &= ~RTW89_PCIE_BIT_L1;
+
+	rtw89_dbi_write8(rtwdev, RTW89_PCIE_L1_CTRL, value);
+}
+
+static void rtw89_pci_link_ps(struct rtw89_dev *rtwdev, bool enter)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+
+	/* Like CLKREQ, ASPM is also implemented by two HW modules, and can
+	 * only be enabled when host supports it.
+	 *
+	 * And ASPM mechanism should be enabled when driver/firmware enters
+	 * power save mode, without having heavy traffic. Because we've
+	 * experienced some inter-operability issues that the link tends
+	 * to enter L1 state on the fly even when driver is having high
+	 * throughput. This is probably because the ASPM behavior slightly
+	 * varies from different SOC.
+	 */
+	if (rtwpci->link_ctrl & PCI_EXP_LNKCTL_ASPM_L1)
+		rtw89_pci_aspm_set(rtwdev, enter);
+}
+
+static void rtw89_pci_link_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct pci_dev *pdev = rtwpci->pdev;
+	u16 link_ctrl;
+	int ret;
+
+	/* Though there is standard PCIE configuration space to set the
+	 * link control register, but by Realtek's design, driver should
+	 * check if host supports CLKREQ/ASPM to enable the HW module.
+	 *
+	 * These functions are implemented by two HW modules associated,
+	 * one is responsible to access PCIE configuration space to
+	 * follow the host settings, and another is in charge of doing
+	 * CLKREQ/ASPM mechanisms, it is default disabled. Because sometimes
+	 * the host does not support it, and due to some reasons or wrong
+	 * settings (ex. CLKREQ# not Bi-Direction), it could lead to device
+	 * loss if HW misbehaves on the link.
+	 *
+	 * Hence it's designed that driver should first check the PCIE
+	 * configuration space is sync'ed and enabled, then driver can turn
+	 * on the other module that is actually working on the mechanism.
+	 */
+	ret = pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &link_ctrl);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to read PCI cap, ret=%d\n", ret);
+		return;
+	}
+
+	if (link_ctrl & PCI_EXP_LNKCTL_CLKREQ_EN)
+		rtw89_pci_clkreq_set(rtwdev, true);
+
+	rtwpci->link_ctrl = link_ctrl;
+}
+
+static void rtw_pci_l1ss_set(struct rtw89_dev *rtwdev, bool enable)
+{
+	u8 value;
+	int ret;
+
+	ret = rtw89_dbi_read8(rtwdev, RTW89_PCIE_TIMER_CTRL, &value);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to read L1SS, ret=%d", ret);
+		return;
+	}
+
+	if (enable)
+		value |= RTW89_PCIE_BIT_L1SUB;
+	else
+		value &= ~RTW89_PCIE_BIT_L1SUB;
+
+	rtw89_dbi_write8(rtwdev, RTW89_PCIE_TIMER_CTRL, value);
+}
+
+static void rtw_pci_l1ss_cfg(struct rtw89_dev *rtwdev)
+{
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	struct pci_dev *pdev = rtwpci->pdev;
+	u32 l1ss_cap_ptr, l1ss_ctrl;
+
+	if (rtw89_pci_disable_l1ss)
+		return;
+
+	l1ss_cap_ptr = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
+	if (!l1ss_cap_ptr)
+		return;
+
+	pci_read_config_dword(pdev, l1ss_cap_ptr + PCI_L1SS_CTL1, &l1ss_ctrl);
+
+	if (l1ss_ctrl & PCI_L1SS_CTL1_L1SS_MASK)
+		rtw_pci_l1ss_set(rtwdev, true);
+}
+
+static void rtw89_pci_ctrl_dma_all_pcie(struct rtw89_dev *rtwdev, u8 en)
+{
+	u32 val32;
+
+	if (en == MAC_AX_FUNC_EN) {
+		val32 = B_AX_STOP_PCIEIO;
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_DMA_STOP1, val32);
+
+		val32 = B_AX_TXHCI_EN | B_AX_RXHCI_EN;
+		rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, val32);
+	} else {
+		val32 = B_AX_STOP_PCIEIO;
+		rtw89_write32_set(rtwdev, R_AX_PCIE_DMA_STOP1, val32);
+
+		val32 = B_AX_TXHCI_EN | B_AX_RXHCI_EN;
+		rtw89_write32_clr(rtwdev, R_AX_PCIE_INIT_CFG1, val32);
+	}
+}
+
+static int rtw89_pci_poll_io_idle(struct rtw89_dev *rtwdev)
+{
+	int ret = 0;
+	u32 sts;
+	u32 busy = B_AX_PCIEIO_BUSY | B_AX_PCIEIO_TX_BUSY | B_AX_PCIEIO_RX_BUSY;
+
+	ret = read_poll_timeout_atomic(rtw89_read32, sts, (sts & busy) == 0x0,
+				       10, 1000, false, rtwdev,
+				       R_AX_PCIE_DMA_BUSY1);
+	if (ret) {
+		rtw89_err(rtwdev, "pci dmach busy1 0x%X\n",
+			  rtw89_read32(rtwdev, R_AX_PCIE_DMA_BUSY1));
+		return -EINVAL;
+	}
+	return ret;
+}
+
+static int rtw89_pci_lv1rst_stop_dma(struct rtw89_dev *rtwdev)
+{
+	rtw89_pci_ctrl_dma_all_pcie(rtwdev, MAC_AX_FUNC_DIS);
+	return rtw89_pci_poll_io_idle(rtwdev);
+}
+
+static void rtw89_pci_ctrl_hci_dma_en(struct rtw89_dev *rtwdev, u8 en)
+{
+	u32 val32;
+
+	if (en == MAC_AX_FUNC_EN) {
+		val32 = B_AX_HCI_TXDMA_EN | B_AX_HCI_RXDMA_EN;
+		rtw89_write32_set(rtwdev, R_AX_HCI_FUNC_EN, val32);
+	} else {
+		val32 = B_AX_HCI_TXDMA_EN | B_AX_HCI_RXDMA_EN;
+		rtw89_write32_clr(rtwdev, R_AX_HCI_FUNC_EN, val32);
+	}
+}
+
+static int rtw89_pci_rst_bdram(struct rtw89_dev *rtwdev)
+{
+	int ret = 0;
+	u32 val32, sts;
+
+	val32 = B_AX_RST_BDRAM;
+	rtw89_write32_set(rtwdev, R_AX_PCIE_INIT_CFG1, val32);
+
+	ret = read_poll_timeout_atomic(rtw89_read32, sts,
+				       (sts & B_AX_RST_BDRAM) == 0x0, 1, 100,
+				       true, rtwdev, R_AX_PCIE_INIT_CFG1);
+	return ret;
+}
+
+static int rtw89_pci_lv1rst_start_dma(struct rtw89_dev *rtwdev)
+{
+	u32 ret;
+
+	rtw89_pci_ctrl_hci_dma_en(rtwdev, MAC_AX_FUNC_DIS);
+	rtw89_pci_ctrl_hci_dma_en(rtwdev, MAC_AX_FUNC_EN);
+	rtw89_pci_clr_idx_all(rtwdev);
+
+	ret = rtw89_pci_rst_bdram(rtwdev);
+	if (ret)
+		return ret;
+
+	rtw89_pci_ctrl_dma_all_pcie(rtwdev, MAC_AX_FUNC_EN);
+	return ret;
+}
+
+static int rtw89_pci_ops_mac_lv1_recovery(struct rtw89_dev *rtwdev, u8 step)
+{
+	int ret;
+
+	switch (step) {
+	case MAC_AX_LV1_RCVY_STEP_1:
+		ret = rtw89_pci_lv1rst_stop_dma(rtwdev);
+		if (ret)
+			rtw89_err(rtwdev, "lv1 rcvy pci stop dma fail\n");
+
+		break;
+
+	case MAC_AX_LV1_RCVY_STEP_2:
+		ret = rtw89_pci_lv1rst_start_dma(rtwdev);
+		if (ret)
+			rtw89_err(rtwdev, "lv1 rcvy pci start dma fail\n");
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static int rtw89_pci_napi_poll(struct napi_struct *napi, int budget)
+{
+	struct rtw89_dev *rtwdev = container_of(napi, struct rtw89_dev, napi);
+	struct rtw89_pci *rtwpci = (struct rtw89_pci *)rtwdev->priv;
+	unsigned long flags;
+	u32 cnt;
+	int ret;
+
+	ret = rtw89_pci_poll_rxq_dma(rtwdev, rtwpci, budget);
+	if (ret < budget) {
+		napi_complete_done(napi, ret);
+
+		cnt = rtw89_pci_rxbd_recalc(rtwdev, &rtwpci->rx_rings[RTW89_RXCH_RXQ]);
+		if (cnt && napi_reschedule(napi))
+			return ret;
+
+		spin_lock_irqsave(&rtwpci->irq_lock, flags);
+		if (rtwpci->running) {
+			rtw89_pci_clear_intrs(rtwdev, rtwpci);
+			rtw89_pci_enable_intr_mask0(rtwdev, rtwpci, B_AX_RXDMA_INTS_MASK);
+		}
+		spin_unlock_irqrestore(&rtwpci->irq_lock, flags);
+	}
+
+	return ret;
+}
+
+static const struct rtw89_hci_ops rtw89_pci_ops = {
+	.tx_write	= rtw89_pci_ops_tx_write,
+	.tx_kick_off	= rtw89_pci_ops_tx_kick_off,
+	.flush_queues	= rtw89_pci_ops_flush_queues,
+	.reset		= rtw89_pci_ops_reset,
+	.start		= rtw89_pci_ops_start,
+	.stop		= rtw89_pci_ops_stop,
+	.link_ps	= rtw89_pci_link_ps,
+
+	.read8		= rtw89_pci_ops_read8,
+	.read16		= rtw89_pci_ops_read16,
+	.read32		= rtw89_pci_ops_read32,
+	.write8		= rtw89_pci_ops_write8,
+	.write16	= rtw89_pci_ops_write16,
+	.write32	= rtw89_pci_ops_write32,
+
+	.mac_pre_init	= rtw89_pci_ops_mac_pre_init,
+	.mac_post_init	= rtw89_pci_ops_mac_post_init,
+	.deinit		= rtw89_pci_ops_deinit,
+
+	.check_and_reclaim_tx_resource = rtw89_pci_check_and_reclaim_tx_resource,
+	.mac_lv1_rcvy	= rtw89_pci_ops_mac_lv1_recovery,
+	.napi_poll	= rtw89_pci_napi_poll,
+};
+
+static int rtw89_pci_probe(struct pci_dev *pdev,
+			   const struct pci_device_id *id)
+{
+	struct ieee80211_hw *hw;
+	struct rtw89_dev *rtwdev;
+	int driver_data_size;
+	int ret;
+
+	driver_data_size = sizeof(struct rtw89_dev) + sizeof(struct rtw89_pci);
+	hw = ieee80211_alloc_hw(driver_data_size, &rtw89_ops);
+	if (!hw) {
+		dev_err(&pdev->dev, "failed to allocate hw\n");
+		return -ENOMEM;
+	}
+
+	rtwdev = hw->priv;
+	rtwdev->hw = hw;
+	rtwdev->dev = &pdev->dev;
+	rtwdev->hci.ops = &rtw89_pci_ops;
+	rtwdev->hci.type = RTW89_HCI_TYPE_PCIE;
+	rtwdev->hci.rpwm_addr = R_AX_PCIE_HRPWM;
+	rtwdev->hci.cpwm_addr = R_AX_CPWM;
+
+	SET_IEEE80211_DEV(rtwdev->hw, &pdev->dev);
+
+	switch (id->driver_data) {
+	case RTL8852A:
+		rtwdev->chip = &rtw8852a_chip_info;
+		break;
+	default:
+		return -ENOENT;
+	}
+
+	ret = rtw89_core_init(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to initialise core\n");
+		goto err_release_hw;
+	}
+
+	ret = rtw89_pci_claim_device(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to claim pci device\n");
+		goto err_core_deinit;
+	}
+
+	ret = rtw89_pci_setup_resource(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to setup pci resource\n");
+		goto err_declaim_pci;
+	}
+
+	ret = rtw89_chip_info_setup(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to setup chip information\n");
+		goto err_clear_resource;
+	}
+
+	rtw89_pci_link_cfg(rtwdev);
+	rtw_pci_l1ss_cfg(rtwdev);
+
+	ret = rtw89_core_register(rtwdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to register core\n");
+		goto err_clear_resource;
+	}
+
+	rtw89_core_napi_init(rtwdev);
+
+	ret = rtw89_pci_request_irq(rtwdev, pdev);
+	if (ret) {
+		rtw89_err(rtwdev, "failed to request pci irq\n");
+		goto err_unregister;
+	}
+
+	return 0;
+
+err_unregister:
+	rtw89_core_napi_deinit(rtwdev);
+	rtw89_core_unregister(rtwdev);
+err_clear_resource:
+	rtw89_pci_clear_resource(rtwdev, pdev);
+err_declaim_pci:
+	rtw89_pci_declaim_device(rtwdev, pdev);
+err_core_deinit:
+	rtw89_core_deinit(rtwdev);
+err_release_hw:
+	ieee80211_free_hw(hw);
+
+	return ret;
+}
+
+static void rtw89_pci_remove(struct pci_dev *pdev)
+{
+	struct ieee80211_hw *hw = pci_get_drvdata(pdev);
+	struct rtw89_dev *rtwdev;
+
+	if (!hw)
+		return;
+
+	rtwdev = hw->priv;
+
+	rtw89_pci_free_irq(rtwdev, pdev);
+	rtw89_core_napi_deinit(rtwdev);
+	rtw89_core_unregister(rtwdev);
+	rtw89_pci_clear_resource(rtwdev, pdev);
+	rtw89_pci_declaim_device(rtwdev, pdev);
+	rtw89_core_deinit(rtwdev);
+	ieee80211_free_hw(hw);
+}
+
+static const struct pci_device_id rtw89_pci_id_table[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8852), .driver_data = RTL8852A },
+	{},
+};
+MODULE_DEVICE_TABLE(pci, rtw89_pci_id_table);
+
+static struct pci_driver rtw89_pci_driver = {
+	.name		= "rtw89_pci",
+	.id_table	= rtw89_pci_id_table,
+	.probe		= rtw89_pci_probe,
+	.remove		= rtw89_pci_remove,
+};
+module_pci_driver(rtw89_pci_driver);
+
+MODULE_AUTHOR("Realtek Corporation");
+MODULE_DESCRIPTION("Realtek 802.11ax wireless PCI driver");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/net/wireless/realtek/rtw89/pci.h b/drivers/net/wireless/realtek/rtw89/pci.h
new file mode 100644
index 000000000000..32eaf28d484d
--- /dev/null
+++ b/drivers/net/wireless/realtek/rtw89/pci.h
@@ -0,0 +1,565 @@ 
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/* Copyright(c) 2020  Realtek Corporation
+ */
+
+#ifndef __RTW89_PCI_H__
+#define __RTW89_PCI_H__
+
+#include "txrx.h"
+
+#define MDIO_PG0_G1 0
+#define MDIO_PG1_G1 1
+#define MDIO_PG0_G2 2
+#define MDIO_PG1_G2 3
+#define RAC_ANA10			0x10
+#define RAC_ANA19			0x19
+#define RAC_ANA1F			0x1F
+#define RAC_ANA24			0x24
+#define RAC_ANA26			0x26
+#define RAC_CTRL_PPR_V1			0x30
+#define RAC_SET_PPR_V1			0x31
+
+#define R_AX_DBI_FLAG			0x1090
+#define B_AX_DBI_RFLAG			BIT(17)
+#define B_AX_DBI_WFLAG			BIT(16)
+#define B_AX_DBI_WREN_MSK		GENMASK(15, 12)
+#define B_AX_DBI_ADDR_MSK		GENMASK(11, 2)
+#define R_AX_DBI_WDATA			0x1094
+#define R_AX_DBI_RDATA			0x1098
+
+#define RTW89_PCI_WR_RETRY_CNT		20
+
+/* Interrupts */
+#define R_AX_HIMR0 0x01A0
+#define B_AX_HALT_C2H_INT_EN BIT(21)
+#define R_AX_HISR0 0x01A4
+
+#define R_AX_MDIO_CFG			0x10A0
+#define B_AX_MDIO_PHY_ADDR_MASK		GENMASK(13, 12)
+#define B_AX_MDIO_RFLAG			BIT(9)
+#define B_AX_MDIO_WFLAG			BIT(8)
+#define B_AX_MDIO_ADDR_MASK		GENMASK(4, 0)
+
+#define R_AX_PCIE_HIMR00	0x10B0
+#define B_AX_HC00ISR_IND_INT_EN		BIT(27)
+#define B_AX_HD1ISR_IND_INT_EN		BIT(26)
+#define B_AX_HD0ISR_IND_INT_EN		BIT(25)
+#define B_AX_HS0ISR_IND_INT_EN		BIT(24)
+#define B_AX_RETRAIN_INT_EN		BIT(21)
+#define B_AX_RPQBD_FULL_INT_EN		BIT(20)
+#define B_AX_RDU_INT_EN			BIT(19)
+#define B_AX_RXDMA_STUCK_INT_EN		BIT(18)
+#define B_AX_TXDMA_STUCK_INT_EN		BIT(17)
+#define B_AX_PCIE_HOTRST_INT_EN		BIT(16)
+#define B_AX_PCIE_FLR_INT_EN		BIT(15)
+#define B_AX_PCIE_PERST_INT_EN		BIT(14)
+#define B_AX_TXDMA_CH12_INT_EN		BIT(13)
+#define B_AX_TXDMA_CH9_INT_EN		BIT(12)
+#define B_AX_TXDMA_CH8_INT_EN		BIT(11)
+#define B_AX_TXDMA_ACH7_INT_EN		BIT(10)
+#define B_AX_TXDMA_ACH6_INT_EN		BIT(9)
+#define B_AX_TXDMA_ACH5_INT_EN		BIT(8)
+#define B_AX_TXDMA_ACH4_INT_EN		BIT(7)
+#define B_AX_TXDMA_ACH3_INT_EN		BIT(6)
+#define B_AX_TXDMA_ACH2_INT_EN		BIT(5)
+#define B_AX_TXDMA_ACH1_INT_EN		BIT(4)
+#define B_AX_TXDMA_ACH0_INT_EN		BIT(3)
+#define B_AX_RPQDMA_INT_EN		BIT(2)
+#define B_AX_RXP1DMA_INT_EN		BIT(1)
+#define B_AX_RXDMA_INT_EN		BIT(0)
+
+#define R_AX_PCIE_HISR00	0x10B4
+#define B_AX_HC00ISR_IND_INT		BIT(27)
+#define B_AX_HD1ISR_IND_INT		BIT(26)
+#define B_AX_HD0ISR_IND_INT		BIT(25)
+#define B_AX_HS0ISR_IND_INT		BIT(24)
+#define B_AX_RETRAIN_INT		BIT(21)
+#define B_AX_RPQBD_FULL_INT		BIT(20)
+#define B_AX_RDU_INT			BIT(19)
+#define B_AX_RXDMA_STUCK_INT		BIT(18)
+#define B_AX_TXDMA_STUCK_INT		BIT(17)
+#define B_AX_PCIE_HOTRST_INT		BIT(16)
+#define B_AX_PCIE_FLR_INT		BIT(15)
+#define B_AX_PCIE_PERST_INT		BIT(14)
+#define B_AX_TXDMA_CH12_INT		BIT(13)
+#define B_AX_TXDMA_CH9_INT		BIT(12)
+#define B_AX_TXDMA_CH8_INT		BIT(11)
+#define B_AX_TXDMA_ACH7_INT		BIT(10)
+#define B_AX_TXDMA_ACH6_INT		BIT(9)
+#define B_AX_TXDMA_ACH5_INT		BIT(8)
+#define B_AX_TXDMA_ACH4_INT		BIT(7)
+#define B_AX_TXDMA_ACH3_INT		BIT(6)
+#define B_AX_TXDMA_ACH2_INT		BIT(5)
+#define B_AX_TXDMA_ACH1_INT		BIT(4)
+#define B_AX_TXDMA_ACH0_INT		BIT(3)
+#define B_AX_RPQDMA_INT			BIT(2)
+#define B_AX_RXP1DMA_INT		BIT(1)
+#define B_AX_RXDMA_INT			BIT(0)
+#define B_AX_RXDMA_INTS_MASK (B_AX_RXDMA_INT | B_AX_RXP1DMA_INT | B_AX_RDU_INT)
+
+#define R_AX_PCIE_HIMR10	0x13B0
+#define B_AX_HC10ISR_IND_INT_EN		BIT(28)
+#define B_AX_TXDMA_CH11_INT_EN		BIT(12)
+#define B_AX_TXDMA_CH10_INT_EN		BIT(11)
+
+#define R_AX_PCIE_HISR10	0x13B4
+#define B_AX_HC10ISR_IND_INT		BIT(28)
+#define B_AX_TXDMA_CH11_INT		BIT(12)
+#define B_AX_TXDMA_CH10_INT		BIT(11)
+
+/* TX/RX */
+#define R_AX_RXQ_RXBD_IDX	0x1050
+#define R_AX_RPQ_RXBD_IDX	0x1054
+#define R_AX_ACH0_TXBD_IDX	0x1058
+#define R_AX_ACH1_TXBD_IDX	0x105C
+#define R_AX_ACH2_TXBD_IDX	0x1060
+#define R_AX_ACH3_TXBD_IDX	0x1064
+#define R_AX_ACH4_TXBD_IDX	0x1068
+#define R_AX_ACH5_TXBD_IDX	0x106C
+#define R_AX_ACH6_TXBD_IDX	0x1070
+#define R_AX_ACH7_TXBD_IDX	0x1074
+#define R_AX_CH8_TXBD_IDX	0x1078 /* Management Queue band 0 */
+#define R_AX_CH9_TXBD_IDX	0x107C /* HI Queue band 0 */
+#define R_AX_CH10_TXBD_IDX	0x137C /* Management Queue band 1 */
+#define R_AX_CH11_TXBD_IDX	0x1380 /* HI Queue band 1 */
+#define R_AX_CH12_TXBD_IDX	0x1080 /* FWCMD Queue */
+#define TXBD_HW_IDX_MASK	GENMASK(27, 16)
+#define TXBD_HOST_IDX_MASK	GENMASK(11, 0)
+
+#define R_AX_ACH0_TXBD_DESA_L	0x1110
+#define R_AX_ACH0_TXBD_DESA_H	0x1114
+#define R_AX_ACH1_TXBD_DESA_L	0x1118
+#define R_AX_ACH1_TXBD_DESA_H	0x111C
+#define R_AX_ACH2_TXBD_DESA_L	0x1120
+#define R_AX_ACH2_TXBD_DESA_H	0x1124
+#define R_AX_ACH3_TXBD_DESA_L	0x1128
+#define R_AX_ACH3_TXBD_DESA_H	0x112C
+#define R_AX_ACH4_TXBD_DESA_L	0x1130
+#define R_AX_ACH4_TXBD_DESA_H	0x1134
+#define R_AX_ACH5_TXBD_DESA_L	0x1138
+#define R_AX_ACH5_TXBD_DESA_H	0x113C
+#define R_AX_ACH6_TXBD_DESA_L	0x1140
+#define R_AX_ACH6_TXBD_DESA_H	0x1144
+#define R_AX_ACH7_TXBD_DESA_L	0x1148
+#define R_AX_ACH7_TXBD_DESA_H	0x114C
+#define R_AX_CH8_TXBD_DESA_L	0x1150
+#define R_AX_CH8_TXBD_DESA_H	0x1154
+#define R_AX_CH9_TXBD_DESA_L	0x1158
+#define R_AX_CH9_TXBD_DESA_H	0x115C
+#define R_AX_CH10_TXBD_DESA_L	0x1358
+#define R_AX_CH10_TXBD_DESA_H	0x135C
+#define R_AX_CH11_TXBD_DESA_L	0x1360
+#define R_AX_CH11_TXBD_DESA_H	0x1364
+#define R_AX_CH12_TXBD_DESA_L	0x1160
+#define R_AX_CH12_TXBD_DESA_H	0x1164
+#define R_AX_RXQ_RXBD_DESA_L	0x1100
+#define R_AX_RXQ_RXBD_DESA_H	0x1104
+#define R_AX_RPQ_RXBD_DESA_L	0x1108
+#define R_AX_RPQ_RXBD_DESA_H	0x110C
+#define B_AX_DESC_NUM_MSK		GENMASK(11, 0)
+
+#define R_AX_RXQ_RXBD_NUM	0x1020
+#define R_AX_RPQ_RXBD_NUM	0x1022
+#define R_AX_ACH0_TXBD_NUM	0x1024
+#define R_AX_ACH1_TXBD_NUM	0x1026
+#define R_AX_ACH2_TXBD_NUM	0x1028
+#define R_AX_ACH3_TXBD_NUM	0x102A
+#define R_AX_ACH4_TXBD_NUM	0x102C
+#define R_AX_ACH5_TXBD_NUM	0x102E
+#define R_AX_ACH6_TXBD_NUM	0x1030
+#define R_AX_ACH7_TXBD_NUM	0x1032
+#define R_AX_CH8_TXBD_NUM	0x1034
+#define R_AX_CH9_TXBD_NUM	0x1036
+#define R_AX_CH10_TXBD_NUM	0x1338
+#define R_AX_CH11_TXBD_NUM	0x133A
+#define R_AX_CH12_TXBD_NUM	0x1038
+
+#define R_AX_ACH0_BDRAM_CTRL	0x1200
+#define R_AX_ACH1_BDRAM_CTRL	0x1204
+#define R_AX_ACH2_BDRAM_CTRL	0x1208
+#define R_AX_ACH3_BDRAM_CTRL	0x120C
+#define R_AX_ACH4_BDRAM_CTRL	0x1210
+#define R_AX_ACH5_BDRAM_CTRL	0x1214
+#define R_AX_ACH6_BDRAM_CTRL	0x1218
+#define R_AX_ACH7_BDRAM_CTRL	0x121C
+#define R_AX_CH8_BDRAM_CTRL	0x1220
+#define R_AX_CH9_BDRAM_CTRL	0x1224
+#define R_AX_CH10_BDRAM_CTRL	0x1320
+#define R_AX_CH11_BDRAM_CTRL	0x1324
+#define R_AX_CH12_BDRAM_CTRL	0x1228
+#define BDRAM_SIDX_MASK		GENMASK(7, 0)
+#define BDRAM_MAX_MASK		GENMASK(15, 8)
+#define BDRAM_MIN_MASK		GENMASK(23, 16)
+
+#define R_AX_PCIE_INIT_CFG1	0x1000
+#define B_AX_PCIE_RXRST_KEEP_REG	BIT(23)
+#define B_AX_PCIE_TXRST_KEEP_REG	BIT(22)
+#define B_AX_PCIE_PERST_KEEP_REG	BIT(21)
+#define B_AX_PCIE_FLR_KEEP_REG		BIT(20)
+#define B_AX_PCIE_TRAIN_KEEP_REG	BIT(19)
+#define B_AX_RXBD_MODE			BIT(18)
+#define B_AX_PCIE_MAX_RXDMA_MASK	GENMASK(16, 14)
+#define B_AX_RXHCI_EN			BIT(13)
+#define B_AX_LATENCY_CONTROL		BIT(12)
+#define B_AX_TXHCI_EN			BIT(11)
+#define B_AX_PCIE_MAX_TXDMA_MASK	GENMASK(10, 8)
+#define B_AX_TX_TRUNC_MODE		BIT(5)
+#define B_AX_RX_TRUNC_MODE		BIT(4)
+#define B_AX_RST_BDRAM			BIT(3)
+#define B_AX_DIS_RXDMA_PRE		BIT(2)
+
+#define R_AX_TXDMA_ADDR_H	0x10F0
+#define R_AX_RXDMA_ADDR_H	0x10F4
+
+#define R_AX_PCIE_DMA_STOP1	0x1010
+#define B_AX_STOP_PCIEIO		BIT(20)
+#define B_AX_STOP_WPDMA			BIT(19)
+#define B_AX_STOP_CH12			BIT(18)
+#define B_AX_STOP_CH9			BIT(17)
+#define B_AX_STOP_CH8			BIT(16)
+#define B_AX_STOP_ACH7			BIT(15)
+#define B_AX_STOP_ACH6			BIT(14)
+#define B_AX_STOP_ACH5			BIT(13)
+#define B_AX_STOP_ACH4			BIT(12)
+#define B_AX_STOP_ACH3			BIT(11)
+#define B_AX_STOP_ACH2			BIT(10)
+#define B_AX_STOP_ACH1			BIT(9)
+#define B_AX_STOP_ACH0			BIT(8)
+#define B_AX_STOP_RPQ			BIT(1)
+#define B_AX_STOP_RXQ			BIT(0)
+#define B_AX_TX_STOP1_ALL		GENMASK(18, 8)
+
+#define R_AX_PCIE_DMA_STOP2	0x1310
+#define B_AX_STOP_CH11			BIT(1)
+#define B_AX_STOP_CH10			BIT(0)
+#define B_AX_TX_STOP2_ALL		GENMASK(1, 0)
+
+#define R_AX_TXBD_RWPTR_CLR1	0x1014
+#define B_AX_CLR_CH12_IDX		BIT(10)
+#define B_AX_CLR_CH9_IDX		BIT(9)
+#define B_AX_CLR_CH8_IDX		BIT(8)
+#define B_AX_CLR_ACH7_IDX		BIT(7)
+#define B_AX_CLR_ACH6_IDX		BIT(6)
+#define B_AX_CLR_ACH5_IDX		BIT(5)
+#define B_AX_CLR_ACH4_IDX		BIT(4)
+#define B_AX_CLR_ACH3_IDX		BIT(3)
+#define B_AX_CLR_ACH2_IDX		BIT(2)
+#define B_AX_CLR_ACH1_IDX		BIT(1)
+#define B_AX_CLR_ACH0_IDX		BIT(0)
+#define B_AX_TXBD_CLR1_ALL		GENMASK(10, 0)
+
+#define R_AX_RXBD_RWPTR_CLR	0x1018
+#define B_AX_CLR_RPQ_IDX		BIT(1)
+#define B_AX_CLR_RXQ_IDX		BIT(0)
+#define B_AX_RXBD_CLR_ALL		GENMASK(1, 0)
+
+#define R_AX_TXBD_RWPTR_CLR2	0x1314
+#define B_AX_CLR_CH11_IDX		BIT(1)
+#define B_AX_CLR_CH10_IDX		BIT(0)
+#define B_AX_TXBD_CLR2_ALL		GENMASK(1, 0)
+
+#define R_AX_PCIE_DMA_BUSY1	0x101C
+#define B_AX_PCIEIO_RX_BUSY		BIT(22)
+#define B_AX_PCIEIO_TX_BUSY		BIT(21)
+#define B_AX_PCIEIO_BUSY		BIT(20)
+#define B_AX_WPDMA_BUSY			BIT(19)
+
+#define R_AX_PCIE_DMA_BUSY2	0x131C
+#define B_AX_CH11_BUSY			BIT(1)
+#define B_AX_CH10_BUSY			BIT(0)
+
+/* Configure */
+#define R_AX_PCIE_INIT_CFG1	0x1000
+#define B_AX_PCIE_RXRST_KEEP_REG	BIT(23)
+#define B_AX_PCIE_TXRST_KEEP_REG	BIT(22)
+#define B_AX_DIS_RXDMA_PRE		BIT(2)
+
+#define R_AX_PCIE_RX_PREF_ADV	0x13F4
+#define B_AX_RXDMA_PREF_ADV_EN		BIT(0)
+
+#define RTW89_PCI_TXBD_NUM_MAX		256
+#define RTW89_PCI_RXBD_NUM_MAX		256
+#define RTW89_PCI_TXWD_NUM_MAX		512
+#define RTW89_PCI_TXWD_PAGE_SIZE	128
+#define RTW89_PCI_ADDRINFO_MAX		4
+#define RTW89_PCI_RX_BUF_SIZE		11460
+
+#define RTW89_PCI_POLL_BDRAM_RST_CNT 100
+
+/* PCIE CFG register */
+#define RTW89_PCIE_TIMER_CTRL		0x0718
+#define RTW89_PCIE_BIT_L1SUB		BIT(5)
+#define RTW89_PCIE_L1_CTRL		0x0719
+#define RTW89_PCIE_BIT_CLK		BIT(4)
+#define RTW89_PCIE_BIT_L1		BIT(3)
+#define RTW89_PCIE_CLK_CTRL		0x0725
+#define RTW89_PCIE_PHY_RATE		0x82
+#define INTF_INTGRA_MINREF_V1	90
+#define INTF_INTGRA_HOSTREF_V1	100
+
+enum rtw89_pcie_phy {
+	PCIE_PHY_GEN1,
+	PCIE_PHY_GEN2,
+	PCIE_PHY_GEN1_UNDEFINE = 0x7F,
+};
+
+enum mac_ax_func_sw {
+	MAC_AX_FUNC_DIS,
+	MAC_AX_FUNC_EN,
+};
+
+enum mac_ax_lv1_rcvy_step {
+	MAC_AX_LV1_RCVY_STEP_1 = 0,
+	MAC_AX_LV1_RCVY_STEP_2
+};
+
+enum rtw89_pcie_clkdly_hw {
+	PCIE_CLKDLY_HW_0 = 0,
+	PCIE_CLKDLY_HW_30US = 0x1,
+	PCIE_CLKDLY_HW_50US = 0x2,
+	PCIE_CLKDLY_HW_100US = 0x3,
+	PCIE_CLKDLY_HW_150US = 0x4,
+	PCIE_CLKDLY_HW_200US = 0x5
+};
+
+struct rtw89_pci_bd_ram {
+	u8 start_idx;
+	u8 max_num;
+	u8 min_num;
+};
+
+struct rtw89_pci_tx_data {
+	dma_addr_t dma;
+};
+
+struct rtw89_pci_rx_info {
+	dma_addr_t dma;
+	u32 fs:1, ls:1, tag:11, len:14;
+};
+
+#define RTW89_PCI_TXBD_OPTION_LS	BIT(14)
+
+struct rtw89_pci_tx_bd_32 {
+	__le16 length;
+	__le16 option;
+	__le32 dma;
+} __packed;
+
+#define RTW89_PCI_TXWP_VALID		BIT(15)
+
+struct rtw89_pci_tx_wp_info {
+	__le16 seq0;
+	__le16 seq1;
+	__le16 seq2;
+	__le16 seq3;
+} __packed;
+
+#define RTW89_PCI_ADDR_MSDU_LS		BIT(15)
+#define RTW89_PCI_ADDR_LS		BIT(14)
+#define RTW89_PCI_ADDR_HIGH(a)		(((a) << 6) & GENMASK(13, 6))
+#define RTW89_PCI_ADDR_NUM(x)		((x) & GENMASK(5, 0))
+
+struct rtw89_pci_tx_addr_info_32 {
+	__le16 length;
+	__le16 option;
+	__le32 dma;
+} __packed;
+
+#define RTW89_PCI_RPP_POLLUTED		BIT(31)
+#define RTW89_PCI_RPP_SEQ		GENMASK(30, 16)
+#define RTW89_PCI_RPP_TX_STATUS		GENMASK(15, 13)
+#define RTW89_TX_DONE			0x0
+#define RTW89_TX_RETRY_LIMIT		0x1
+#define RTW89_TX_LIFE_TIME		0x2
+#define RTW89_TX_MACID_DROP		0x3
+#define RTW89_PCI_RPP_QSEL		GENMASK(12, 8)
+#define RTW89_PCI_RPP_MACID		GENMASK(7, 0)
+
+struct rtw89_pci_rpp_fmt {
+	__le32 dword;
+} __packed;
+
+struct rtw89_pci_rx_bd_32 {
+	__le16 buf_size;
+	__le16 rsvd;
+	__le32 dma;
+} __packed;
+
+#define RTW89_PCI_RXBD_FS		BIT(15)
+#define RTW89_PCI_RXBD_LS		BIT(14)
+#define RTW89_PCI_RXBD_WRITE_SIZE	GENMASK(13, 0)
+#define RTW89_PCI_RXBD_TAG		GENMASK(28, 16)
+
+struct rtw89_pci_rxbd_info {
+	__le32 dword;
+};
+
+struct rtw89_pci_tx_wd {
+	struct list_head list;
+	struct sk_buff_head queue;
+
+	void *vaddr;
+	dma_addr_t paddr;
+	u32 len;
+	u32 seq;
+};
+
+struct rtw89_pci_dma_ring {
+	void *head;
+	u8 desc_size;
+	dma_addr_t dma;
+
+	u32 addr_num;
+	u32 addr_idx;
+	u32 addr_bdram;
+	u32 addr_desa_l;
+	u32 addr_desa_h;
+
+	u32 len;
+	u32 wp; /* host idx */
+	u32 rp; /* hw idx */
+};
+
+struct rtw89_pci_tx_wd_ring {
+	void *head;
+	dma_addr_t dma;
+
+	struct rtw89_pci_tx_wd pages[RTW89_PCI_TXWD_NUM_MAX];
+	struct list_head free_pages;
+
+	u32 page_size;
+	u32 page_num;
+	u32 curr_num;
+};
+
+#define RTW89_RX_TAG_MAX		0x1fff
+
+struct rtw89_pci_tx_ring {
+	struct rtw89_pci_tx_wd_ring wd_ring;
+	struct rtw89_pci_dma_ring bd_ring;
+	struct list_head busy_pages;
+	u8 txch;
+	bool dma_enabled;
+	u16 tag; /* range from 0x0001 ~ 0x1fff */
+
+	u64 tx_cnt;
+	u64 tx_acked;
+	u64 tx_retry_lmt;
+	u64 tx_life_time;
+	u64 tx_mac_id_drop;
+};
+
+struct rtw89_pci_rx_ring {
+	struct rtw89_pci_dma_ring bd_ring;
+	struct sk_buff *buf[RTW89_PCI_RXBD_NUM_MAX];
+	u32 buf_sz;
+	struct sk_buff *diliver_skb;
+	struct rtw89_rx_desc_info diliver_desc;
+};
+
+struct rtw89_pci {
+	struct pci_dev *pdev;
+
+	/* protect HW irq related registers */
+	spinlock_t irq_lock;
+	/* protect TRX resources (exclude RXQ) */
+	spinlock_t trx_lock;
+	bool running;
+	struct rtw89_pci_tx_ring tx_rings[RTW89_TXCH_NUM];
+	struct rtw89_pci_rx_ring rx_rings[RTW89_RXCH_NUM];
+	struct sk_buff_head h2c_queue;
+
+	u32 halt_c2h_isrs;
+	u32 halt_c2h_intrs;
+	u32 intrs[2];
+	u32 isrs[2];
+	u16 link_ctrl;
+	void __iomem *mmap;
+};
+
+static inline struct rtw89_pci_rx_info *RTW89_PCI_RX_SKB_CB(struct sk_buff *skb)
+{
+	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+
+	BUILD_BUG_ON(sizeof(struct rtw89_pci_tx_data) >
+		     sizeof(info->status.status_driver_data));
+
+	return (struct rtw89_pci_rx_info *)skb->cb;
+}
+
+static inline struct rtw89_pci_rx_bd_32 *
+RTW89_PCI_RX_BD(struct rtw89_pci_rx_ring *rx_ring, u32 idx)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+	u8 *head = bd_ring->head;
+	u32 desc_size = bd_ring->desc_size;
+	u32 offset = idx * desc_size;
+
+	return (struct rtw89_pci_rx_bd_32 *)(head + offset);
+}
+
+static inline void
+rtw89_pci_rxbd_increase(struct rtw89_pci_rx_ring *rx_ring, u32 cnt)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &rx_ring->bd_ring;
+
+	bd_ring->wp += cnt;
+
+	if (bd_ring->wp >= bd_ring->len)
+		bd_ring->wp -= bd_ring->len;
+}
+
+static inline struct rtw89_pci_tx_data *RTW89_PCI_TX_SKB_CB(struct sk_buff *skb)
+{
+	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+
+	return (struct rtw89_pci_tx_data *)info->status.status_driver_data;
+}
+
+static inline struct rtw89_pci_tx_bd_32 *
+rtw89_pci_get_next_txbd(struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_dma_ring *bd_ring = &tx_ring->bd_ring;
+	struct rtw89_pci_tx_bd_32 *tx_bd, *head;
+
+	head = bd_ring->head;
+	tx_bd = head + bd_ring->wp;
+
+	return tx_bd;
+}
+
+static inline struct rtw89_pci_tx_wd *
+rtw89_pci_dequeue_txwd(struct rtw89_pci_tx_ring *tx_ring)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+	struct rtw89_pci_tx_wd *txwd;
+
+	txwd = list_first_entry_or_null(&wd_ring->free_pages,
+					struct rtw89_pci_tx_wd, list);
+	if (!txwd)
+		return NULL;
+
+	list_del_init(&txwd->list);
+	txwd->len = 0;
+	wd_ring->curr_num--;
+
+	return txwd;
+}
+
+static inline void
+rtw89_pci_enqueue_txwd(struct rtw89_pci_tx_ring *tx_ring,
+		       struct rtw89_pci_tx_wd *txwd)
+{
+	struct rtw89_pci_tx_wd_ring *wd_ring = &tx_ring->wd_ring;
+
+	memset(txwd->vaddr, 0, wd_ring->page_size);
+	list_add_tail(&txwd->list, &wd_ring->free_pages);
+	wd_ring->curr_num++;
+}
+
+static inline bool rtw89_pci_ltr_is_err_reg_val(u32 val)
+{
+	return val == 0xffffffff || val == 0xeaeaeaea;
+}
+
+#endif