| Message ID | 1626443927-32028-3-git-send-email-pmaliset@codeaurora.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add DT bindings and DT nodes for PCIe and PHY in SC7280 | expand |
Quoting Prasad Malisetty (2021-07-16 06:58:45) > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi > index a8c274a..06baf88 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi > @@ -15,6 +15,7 @@ > #include <dt-bindings/reset/qcom,sdm845-pdc.h> > #include <dt-bindings/soc/qcom,rpmh-rsc.h> > #include <dt-bindings/thermal/thermal.h> > +#include <dt-bindings/gpio/gpio.h> > > / { > interrupt-parent = <&intc>; > @@ -546,6 +547,118 @@ > #power-domain-cells = <1>; Is this the gpucc node? At address 3d90000? Please sort the nodes based on their address, so this would be 1c08000 which comes before gpucc and some others in this file. > }; > > + pcie1: pci@1c08000 { > + compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250", "snps,dw-pcie"; > + reg = <0 0x01c08000 0 0x3000>, > + <0 0x40000000 0 0xf1d>, > + <0 0x40000f20 0 0xa8>, > + <0 0x40001000 0 0x1000>, > + <0 0x40100000 0 0x100000>; > +
On 2021-07-17 01:01, Stephen Boyd wrote: > Quoting Prasad Malisetty (2021-07-16 06:58:45) >> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi >> b/arch/arm64/boot/dts/qcom/sc7280.dtsi >> index a8c274a..06baf88 100644 >> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi >> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi >> @@ -15,6 +15,7 @@ >> #include <dt-bindings/reset/qcom,sdm845-pdc.h> >> #include <dt-bindings/soc/qcom,rpmh-rsc.h> >> #include <dt-bindings/thermal/thermal.h> >> +#include <dt-bindings/gpio/gpio.h> >> >> / { >> interrupt-parent = <&intc>; >> @@ -546,6 +547,118 @@ >> #power-domain-cells = <1>; > > Is this the gpucc node? At address 3d90000? Please sort the nodes based > on their address, so this would be 1c08000 which comes before gpucc and > some others in this file. > sure, I will move it accordingly. >> }; >> >> + pcie1: pci@1c08000 { >> + compatible = "qcom,pcie-sc7280", >> "qcom,pcie-sm8250", "snps,dw-pcie"; >> + reg = <0 0x01c08000 0 0x3000>, >> + <0 0x40000000 0 0xf1d>, >> + <0 0x40000f20 0 0xa8>, >> + <0 0x40001000 0 0x1000>, >> + <0 0x40100000 0 0x100000>; >> +
On Fri, Jul 16, 2021 at 07:28:45PM +0530, Prasad Malisetty wrote: > Add PCIe controller and PHY nodes for sc7280 SOC. > > Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> > --- > arch/arm64/boot/dts/qcom/sc7280.dtsi | 125 +++++++++++++++++++++++++++++++++++ > 1 file changed, 125 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi > index a8c274a..06baf88 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi > @@ -15,6 +15,7 @@ > #include <dt-bindings/reset/qcom,sdm845-pdc.h> > #include <dt-bindings/soc/qcom,rpmh-rsc.h> > #include <dt-bindings/thermal/thermal.h> > +#include <dt-bindings/gpio/gpio.h> > > / { > interrupt-parent = <&intc>; > @@ -546,6 +547,118 @@ > #power-domain-cells = <1>; > }; > > + pcie1: pci@1c08000 { > + compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250", "snps,dw-pcie"; > + reg = <0 0x01c08000 0 0x3000>, > + <0 0x40000000 0 0xf1d>, > + <0 0x40000f20 0 0xa8>, > + <0 0x40001000 0 0x1000>, > + <0 0x40100000 0 0x100000>; > + > + reg-names = "parf", "dbi", "elbi", "atu", "config"; > + device_type = "pci"; > + linux,pci-domain = <1>; > + bus-range = <0x00 0xff>; > + num-lanes = <2>; > + > + #address-cells = <3>; > + #size-cells = <2>; > + > + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, > + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; > + > + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; > + > + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, > + <&gcc GCC_PCIE_1_PIPE_CLK_SRC>, > + <&pcie1_lane 0>, > + <&rpmhcc RPMH_CXO_CLK>, > + <&gcc GCC_PCIE_1_AUX_CLK>, > + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, > + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, > + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, > + <&gcc GCC_DDRSS_PCIE_SF_CLK>; > + > + clock-names = "pipe", > + "pipe_mux", > + "phy_pipe", > + "ref", > + "aux", > + "cfg", > + "bus_master", > + "bus_slave", > + "slave_q2a", > + "tbu", > + "ddrss_sf_tbu"; > + > + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; > + assigned-clock-rates = <19200000>; > + > + resets = <&gcc GCC_PCIE_1_BCR>; > + reset-names = "pci"; > + > + power-domains = <&gcc GCC_PCIE_1_GDSC>; > + > + phys = <&pcie1_lane>; > + phy-names = "pciephy"; > + > + perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie1_default_state>; > + > + iommus = <&apps_smmu 0x1c80 0x1>; > + > + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, > + <0x100 &apps_smmu 0x1c81 0x1>; > + > + status = "disabled"; > + }; > + > + pcie1_phy: phy@1c0e000 { > + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; > + reg = <0 0x01c0e000 0 0x1c0>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + clocks = <&gcc GCC_PCIE_1_AUX_CLK>, > + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_CLKREF_EN>, > + <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; > + clock-names = "aux", "cfg_ahb", "ref", "refgen"; > + > + resets = <&gcc GCC_PCIE_1_PHY_BCR>; > + reset-names = "phy"; > + > + assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; > + assigned-clock-rates = <100000000>; > + > + status = "disabled"; > + > + pcie1_lane: lanes@1c0e200 { > + reg = <0 0x01c0e200 0 0x170>, > + <0 0x01c0e400 0 0x200>, > + <0 0x01c0ea00 0 0x1f0>, > + <0 0x01c0e600 0 0x170>, > + <0 0x01c0e800 0 0x200>, > + <0 0x01c0ee00 0 0xf4>; > + clocks = <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "pipe0"; > + > + #phy-cells = <0>; > + #clock-cells = <1>; > + clock-output-names = "pcie_1_pipe_clk"; > + }; > + }; > + > stm@6002000 { > compatible = "arm,coresight-stm", "arm,primecell"; > reg = <0 0x06002000 0 0x1000>, > @@ -1185,6 +1298,18 @@ > pins = "gpio46", "gpio47"; > function = "qup13"; > }; > + > + pcie1_default_state: pcie1-default-state { > + clkreq { > + pins = "gpio79"; > + function = "pcie1_clkreqn"; > + }; > + > + wake-n { > + pins = "gpio3"; > + function = "gpio"; > + }; This could be essentially any GPIO, right? Does it really make sense to have this node in the SoC file? I would say it belongs in the board file.
On 2021-08-03 00:53, Matthias Kaehlcke wrote: > On Fri, Jul 16, 2021 at 07:28:45PM +0530, Prasad Malisetty wrote: >> Add PCIe controller and PHY nodes for sc7280 SOC. >> >> Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> >> --- >> arch/arm64/boot/dts/qcom/sc7280.dtsi | 125 >> +++++++++++++++++++++++++++++++++++ >> 1 file changed, 125 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi >> b/arch/arm64/boot/dts/qcom/sc7280.dtsi >> index a8c274a..06baf88 100644 >> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi >> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi >> @@ -15,6 +15,7 @@ >> #include <dt-bindings/reset/qcom,sdm845-pdc.h> >> #include <dt-bindings/soc/qcom,rpmh-rsc.h> >> #include <dt-bindings/thermal/thermal.h> >> +#include <dt-bindings/gpio/gpio.h> >> >> / { >> interrupt-parent = <&intc>; >> @@ -546,6 +547,118 @@ >> #power-domain-cells = <1>; >> }; >> >> + pcie1: pci@1c08000 { >> + compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250", >> "snps,dw-pcie"; >> + reg = <0 0x01c08000 0 0x3000>, >> + <0 0x40000000 0 0xf1d>, >> + <0 0x40000f20 0 0xa8>, >> + <0 0x40001000 0 0x1000>, >> + <0 0x40100000 0 0x100000>; >> + >> + reg-names = "parf", "dbi", "elbi", "atu", "config"; >> + device_type = "pci"; >> + linux,pci-domain = <1>; >> + bus-range = <0x00 0xff>; >> + num-lanes = <2>; >> + >> + #address-cells = <3>; >> + #size-cells = <2>; >> + >> + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, >> + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; >> + >> + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "msi"; >> + #interrupt-cells = <1>; >> + interrupt-map-mask = <0 0 0 0x7>; >> + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, >> + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, >> + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, >> + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; >> + >> + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, >> + <&gcc GCC_PCIE_1_PIPE_CLK_SRC>, >> + <&pcie1_lane 0>, >> + <&rpmhcc RPMH_CXO_CLK>, >> + <&gcc GCC_PCIE_1_AUX_CLK>, >> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, >> + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, >> + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, >> + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, >> + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, >> + <&gcc GCC_DDRSS_PCIE_SF_CLK>; >> + >> + clock-names = "pipe", >> + "pipe_mux", >> + "phy_pipe", >> + "ref", >> + "aux", >> + "cfg", >> + "bus_master", >> + "bus_slave", >> + "slave_q2a", >> + "tbu", >> + "ddrss_sf_tbu"; >> + >> + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; >> + assigned-clock-rates = <19200000>; >> + >> + resets = <&gcc GCC_PCIE_1_BCR>; >> + reset-names = "pci"; >> + >> + power-domains = <&gcc GCC_PCIE_1_GDSC>; >> + >> + phys = <&pcie1_lane>; >> + phy-names = "pciephy"; >> + >> + perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pcie1_default_state>; >> + >> + iommus = <&apps_smmu 0x1c80 0x1>; >> + >> + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, >> + <0x100 &apps_smmu 0x1c81 0x1>; >> + >> + status = "disabled"; >> + }; >> + >> + pcie1_phy: phy@1c0e000 { >> + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; >> + reg = <0 0x01c0e000 0 0x1c0>; >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + clocks = <&gcc GCC_PCIE_1_AUX_CLK>, >> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, >> + <&gcc GCC_PCIE_CLKREF_EN>, >> + <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; >> + clock-names = "aux", "cfg_ahb", "ref", "refgen"; >> + >> + resets = <&gcc GCC_PCIE_1_PHY_BCR>; >> + reset-names = "phy"; >> + >> + assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; >> + assigned-clock-rates = <100000000>; >> + >> + status = "disabled"; >> + >> + pcie1_lane: lanes@1c0e200 { >> + reg = <0 0x01c0e200 0 0x170>, >> + <0 0x01c0e400 0 0x200>, >> + <0 0x01c0ea00 0 0x1f0>, >> + <0 0x01c0e600 0 0x170>, >> + <0 0x01c0e800 0 0x200>, >> + <0 0x01c0ee00 0 0xf4>; >> + clocks = <&rpmhcc RPMH_CXO_CLK>; >> + clock-names = "pipe0"; >> + >> + #phy-cells = <0>; >> + #clock-cells = <1>; >> + clock-output-names = "pcie_1_pipe_clk"; >> + }; >> + }; >> + >> stm@6002000 { >> compatible = "arm,coresight-stm", "arm,primecell"; >> reg = <0 0x06002000 0 0x1000>, >> @@ -1185,6 +1298,18 @@ >> pins = "gpio46", "gpio47"; >> function = "qup13"; >> }; >> + >> + pcie1_default_state: pcie1-default-state { >> + clkreq { >> + pins = "gpio79"; >> + function = "pcie1_clkreqn"; >> + }; >> + >> + wake-n { >> + pins = "gpio3"; >> + function = "gpio"; >> + }; > > This could be essentially any GPIO, right? Does it really make sense to > have this node in the SoC file? I would say it belongs in the board > file. Hi Matthias, Thanks for your review and comments. Sorry for the delay in acknowledging. I would move this entry in IDP file in next version. Thanks -Prasad
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index a8c274a..06baf88 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -15,6 +15,7 @@ #include <dt-bindings/reset/qcom,sdm845-pdc.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> #include <dt-bindings/thermal/thermal.h> +#include <dt-bindings/gpio/gpio.h> / { interrupt-parent = <&intc>; @@ -546,6 +547,118 @@ #power-domain-cells = <1>; }; + pcie1: pci@1c08000 { + compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c08000 0 0x3000>, + <0 0x40000000 0 0xf1d>, + <0 0x40000f20 0 0xa8>, + <0 0x40001000 0 0x1000>, + <0 0x40100000 0 0x100000>; + + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <1>; + bus-range = <0x00 0xff>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; + + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, + <&gcc GCC_PCIE_1_PIPE_CLK_SRC>, + <&pcie1_lane 0>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_CLK>; + + clock-names = "pipe", + "pipe_mux", + "phy_pipe", + "ref", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "tbu", + "ddrss_sf_tbu"; + + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; + assigned-clock-rates = <19200000>; + + resets = <&gcc GCC_PCIE_1_BCR>; + reset-names = "pci"; + + power-domains = <&gcc GCC_PCIE_1_GDSC>; + + phys = <&pcie1_lane>; + phy-names = "pciephy"; + + perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_default_state>; + + iommus = <&apps_smmu 0x1c80 0x1>; + + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, + <0x100 &apps_smmu 0x1c81 0x1>; + + status = "disabled"; + }; + + pcie1_phy: phy@1c0e000 { + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; + reg = <0 0x01c0e000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_CLKREF_EN>, + <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_1_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie1_lane: lanes@1c0e200 { + reg = <0 0x01c0e200 0 0x170>, + <0 0x01c0e400 0 0x200>, + <0 0x01c0ea00 0 0x1f0>, + <0 0x01c0e600 0 0x170>, + <0 0x01c0e800 0 0x200>, + <0 0x01c0ee00 0 0xf4>; + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + #clock-cells = <1>; + clock-output-names = "pcie_1_pipe_clk"; + }; + }; + stm@6002000 { compatible = "arm,coresight-stm", "arm,primecell"; reg = <0 0x06002000 0 0x1000>, @@ -1185,6 +1298,18 @@ pins = "gpio46", "gpio47"; function = "qup13"; }; + + pcie1_default_state: pcie1-default-state { + clkreq { + pins = "gpio79"; + function = "pcie1_clkreqn"; + }; + + wake-n { + pins = "gpio3"; + function = "gpio"; + }; + }; }; apps_smmu: iommu@15000000 {
Add PCIe controller and PHY nodes for sc7280 SOC. Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> --- arch/arm64/boot/dts/qcom/sc7280.dtsi | 125 +++++++++++++++++++++++++++++++++++ 1 file changed, 125 insertions(+)