| Message ID | 20210719085402.28569-1-lokeshvutla@ti.com |
|---|---|
| Headers | show |
| Series | arm64: dts: ti: k3-am64: Add PWM nodes | expand |
On 19/07/21 8:53 pm, Nishanth Menon wrote: > On 14:24-20210719, Lokesh Vutla wrote: >> ecap0 can be configured to use pad ECAP0_IN_APWM_OUT (D18) which has a >> signal connected to Pin 1 of J3. Add support for adding this pinmux so >> that pwm can be observed on pin 1 of Header J3 >> >> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> >> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> >> --- >> arch/arm64/boot/dts/ti/k3-am642-sk.dts | 12 ++++++++++++ >> 1 file changed, 12 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts >> index d3aa2901e6fd..eb0d10e6e787 100644 >> --- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts >> +++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts >> @@ -210,6 +210,12 @@ AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */ >> AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */ >> >; >> }; >> + >> + main_ecap0_pins_default: main-ecap0-pins-default { >> + pinctrl-single,pins = < >> + AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */ >> + >; >> + }; >> }; >> >> &mcu_uart0 { >> @@ -453,3 +459,9 @@ &pcie0_rc { >> &pcie0_ep { >> status = "disabled"; >> }; >> + >> +&ecap0 { >> + /* PWM is available on Pin 1 of header J3 */ >> + pinctrl-names = "default"; >> + pinctrl-0 = <&main_ecap0_pins_default>; >> +}; >> -- >> 2.30.0 >> > > > Do the other ecap and pwm nodes need to be disabled since they may not > be pinned out? Sure, Ill mark other ecap and epwm nodes as disabled. After looking at schematics, epwm4 and 5 is pinned out on RPI header. But the header will most likely be used for other use-cases. Shall I mark epwm4 and epwm5 disabled as well with a comment with this information? Thanks and regards, Lokesh >
On 10:46-20210720, Lokesh Vutla wrote: > > > On 19/07/21 8:53 pm, Nishanth Menon wrote: > > On 14:24-20210719, Lokesh Vutla wrote: > >> ecap0 can be configured to use pad ECAP0_IN_APWM_OUT (D18) which has a > >> signal connected to Pin 1 of J3. Add support for adding this pinmux so > >> that pwm can be observed on pin 1 of Header J3 > >> > >> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> > >> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> > >> --- > >> arch/arm64/boot/dts/ti/k3-am642-sk.dts | 12 ++++++++++++ > >> 1 file changed, 12 insertions(+) > >> > >> diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts > >> index d3aa2901e6fd..eb0d10e6e787 100644 > >> --- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts > >> +++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts > >> @@ -210,6 +210,12 @@ AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */ > >> AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */ > >> >; > >> }; > >> + > >> + main_ecap0_pins_default: main-ecap0-pins-default { > >> + pinctrl-single,pins = < > >> + AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */ > >> + >; > >> + }; > >> }; > >> > >> &mcu_uart0 { > >> @@ -453,3 +459,9 @@ &pcie0_rc { > >> &pcie0_ep { > >> status = "disabled"; > >> }; > >> + > >> +&ecap0 { > >> + /* PWM is available on Pin 1 of header J3 */ > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&main_ecap0_pins_default>; > >> +}; > >> -- > >> 2.30.0 > >> > > > > > > Do the other ecap and pwm nodes need to be disabled since they may not > > be pinned out? > > Sure, Ill mark other ecap and epwm nodes as disabled. After looking at > schematics, epwm4 and 5 is pinned out on RPI header. But the header will most > likely be used for other use-cases. Shall I mark epwm4 and epwm5 disabled as > well with a comment with this information? Yes, please. Thanks. -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D