| Message ID | 4147230b-e88f-52e8-1241-ad343f77628f@gmail.com |
|---|---|
| State | Accepted |
| Commit | 44c54c4ec391412c7f529e53d27844dadc6d536a |
| Headers | show |
| Series | i2c: i801: Improve status polling | expand |
Hi Heiner, On Tue, 25 May 2021 21:59:05 +0200, Heiner Kallweit wrote: > Polling uses the same timeout as irq mode: 400 * 500us = 200ms = HZ / 5. > So let's use the adapter->timeout value also for polling. This has the > advantage that userspace can control the timeout value for polling as > well. In addition change the code to make it better readable. > Last but not least remove the timeout debug messages. Calls to both > functions are followed by a call to i801_check_post() that will print > an error message in case of timeout. I think that the intent was to differentiate between regular polling and BYTE_DONE polling. But I agree it's not really important, as the caller probably already knows which type of transaction failed (simple or block). > Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> > --- > drivers/i2c/busses/i2c-i801.c | 36 +++++++++++++---------------------- > 1 file changed, 13 insertions(+), 23 deletions(-) > (...) Reviewed-by: Jean Delvare <jdelvare@suse.de> Tested-by: Jean Delvare <jdelvare@suse.de> -- Jean Delvare SUSE L3 Support
On Tue, May 25, 2021 at 09:59:05PM +0200, Heiner Kallweit wrote: > Polling uses the same timeout as irq mode: 400 * 500us = 200ms = HZ / 5. > So let's use the adapter->timeout value also for polling. This has the > advantage that userspace can control the timeout value for polling as > well. In addition change the code to make it better readable. > Last but not least remove the timeout debug messages. Calls to both > functions are followed by a call to i801_check_post() that will print > an error message in case of timeout. > > Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Applied to for-next, thanks!
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index f6d7866f1..2c6e84108 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -156,9 +156,6 @@ #define SMBAUXCTL_CRC BIT(0) #define SMBAUXCTL_E32B BIT(1) -/* Other settings */ -#define MAX_RETRIES 400 - /* I801 command constants */ #define I801_QUICK 0x00 #define I801_BYTE 0x04 @@ -447,42 +444,35 @@ static int i801_check_post(struct i801_priv *priv, int status) /* Wait for BUSY being cleared and either INTR or an error flag being set */ static int i801_wait_intr(struct i801_priv *priv) { - int timeout = 0; - int status; + unsigned long timeout = jiffies + priv->adapter.timeout; + int status, busy; - /* We will always wait for a fraction of a second! */ do { usleep_range(250, 500); status = inb_p(SMBHSTSTS(priv)); - } while (((status & SMBHSTSTS_HOST_BUSY) || - !(status & (STATUS_ERROR_FLAGS | SMBHSTSTS_INTR))) && - (timeout++ < MAX_RETRIES)); + busy = status & SMBHSTSTS_HOST_BUSY; + status &= STATUS_ERROR_FLAGS | SMBHSTSTS_INTR; + if (!busy && status) + return status; + } while (time_is_after_eq_jiffies(timeout)); - if (timeout > MAX_RETRIES) { - dev_dbg(&priv->pci_dev->dev, "INTR Timeout!\n"); - return -ETIMEDOUT; - } - return status & (STATUS_ERROR_FLAGS | SMBHSTSTS_INTR); + return -ETIMEDOUT; } /* Wait for either BYTE_DONE or an error flag being set */ static int i801_wait_byte_done(struct i801_priv *priv) { - int timeout = 0; + unsigned long timeout = jiffies + priv->adapter.timeout; int status; - /* We will always wait for a fraction of a second! */ do { usleep_range(250, 500); status = inb_p(SMBHSTSTS(priv)); - } while (!(status & (STATUS_ERROR_FLAGS | SMBHSTSTS_BYTE_DONE)) && - (timeout++ < MAX_RETRIES)); + if (status & (STATUS_ERROR_FLAGS | SMBHSTSTS_BYTE_DONE)) + return status & STATUS_ERROR_FLAGS; + } while (time_is_after_eq_jiffies(timeout)); - if (timeout > MAX_RETRIES) { - dev_dbg(&priv->pci_dev->dev, "BYTE_DONE Timeout!\n"); - return -ETIMEDOUT; - } - return status & STATUS_ERROR_FLAGS; + return -ETIMEDOUT; } static int i801_transaction(struct i801_priv *priv, int xact)
Polling uses the same timeout as irq mode: 400 * 500us = 200ms = HZ / 5. So let's use the adapter->timeout value also for polling. This has the advantage that userspace can control the timeout value for polling as well. In addition change the code to make it better readable. Last but not least remove the timeout debug messages. Calls to both functions are followed by a call to i801_check_post() that will print an error message in case of timeout. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> --- drivers/i2c/busses/i2c-i801.c | 36 +++++++++++++---------------------- 1 file changed, 13 insertions(+), 23 deletions(-)