| Message ID | 20210602120752.46154-2-manivannan.sadhasivam@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | Add Qualcomm PCIe Endpoint driver support | expand |
On Wed, Jun 2, 2021 at 7:08 AM Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> wrote: > > Add devicetree binding for Qualcomm PCIe EP controller used in platforms > like SDX55. The EP controller is based on the Designware core with > Qualcomm specific wrappers. Is the block EP only or configurable EP or host? > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 139 ++++++++++++++++++ > 1 file changed, 139 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml > > diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml > new file mode 100644 > index 000000000000..0f9140e93bcb > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml > @@ -0,0 +1,139 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm PCIe Endpoint Controller binding > + > +maintainers: > + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > + > +allOf: > + - $ref: "pci-ep.yaml#" > + > +properties: > + compatible: > + const: qcom,pcie-ep SoC specific please. > + > + reg: > + items: > + - description: Designware PCIe registers > + - description: External local bus interface registers > + - description: Address Translation Unit (ATU) registers > + - description: Memory region used to map remote RC address space > + - description: Qualcomm specific PARF configuration registers > + - description: Qualcomm specific TCSR registers > + > + reg-names: > + items: > + - const: dbi > + - const: elbi > + - const: atu > + - const: addr_space > + - const: parf > + - const: tcsr This should be in the same order as the host side. Unfortunately, that's not consistent, but to pick one: reg-names = "parf", "dbi", "elbi", "atu", "config"; > + > + clocks: > + items: > + - description: PCIe CFG AHB clock > + - description: PCIe Auxiliary clock > + - description: PCIe Master AXI clock > + - description: PCIe Slave AXI clock > + - description: PCIe Reference clock > + - description: PCIe Sleep clock > + - description: PCIe Slave Q2A AXI clock > + > + clock-names: > + items: > + - const: cfg > + - const: aux > + - const: bus_master > + - const: bus_slave > + - const: ref > + - const: sleep > + - const: slave_q2a Again, try to keep the same ordering. I have to wonder where 'pipe' clock is that most of the QCom implementations have? > + > + interrupts: > + maxItems: 1 > + description: PCIe Global interrupt > + > + interrupt-names: > + const: int_global 'int_' is redundant, drop. > + > + perst-gpios: > + description: PCIe endpoint reset GPIO An input, right? > + maxItems: 1 > + > + wake-gpios: > + description: PCIe endpoint wake GPIO > + maxItems: 1 > + > + resets: > + maxItems: 1 > + > + reset-names: > + const: core_reset Not yet another name. We already have 'pci' and 'core' in the cases of a single reset. > + > + power-domains: > + maxItems: 1 > + > + phys: > + maxItems: 1 > + > + phy-names: > + const: pciephy > + > +required: > + - compatible > + - reg > + - reg-names > + - clocks > + - clock-names > + - interrupts > + - interrupt-names > + - perst-gpios > + - resets > + - reset-names > + - power-domains > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/qcom,gcc-sdx55.h> > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + pcie_ep: pcie-ep@40000000 { > + compatible = "qcom,pcie-ep"; > + > + reg = <0x40000000 0xf1d>, > + <0x40000f20 0xc8>, > + <0x40001000 0x1000>, > + <0x42000000 0x1000>, > + <0x01c00000 0x3000>, > + <0x01fcb000 0x1000>; > + reg-names = "dbi", "elbi", "atu", "addr_space", "parf", "tcsr"; > + > + clocks = <&gcc GCC_PCIE_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_AUX_CLK>, > + <&gcc GCC_PCIE_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_SLV_AXI_CLK>, > + <&gcc GCC_PCIE_0_CLKREF_CLK>, > + <&gcc GCC_PCIE_SLEEP_CLK>, > + <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>; > + clock-names = "cfg", "aux", "bus_master", "bus_slave", > + "ref", "sleep", "slave_q2a"; > + > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "int_global"; > + perst-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; > + wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; > + resets = <&gcc GCC_PCIE_BCR>; > + reset-names = "core_reset"; > + power-domains = <&gcc PCIE_GDSC>; > + phys = <&pcie0_lane>; > + phy-names = "pciephy"; > + max-link-speed = <3>; > + num-lanes = <2>; Should be documented. I'd assume the max is less than 16 which is presumably what pcie-ep.yaml allows. > + }; > -- > 2.25.1 >
On Wed, Jun 02, 2021 at 09:22:29AM -0500, Rob Herring wrote: > On Wed, Jun 2, 2021 at 7:08 AM Manivannan Sadhasivam > <manivannan.sadhasivam@linaro.org> wrote: > > > > Add devicetree binding for Qualcomm PCIe EP controller used in platforms > > like SDX55. The EP controller is based on the Designware core with > > Qualcomm specific wrappers. > > Is the block EP only or configurable EP or host? > Configurable core. We already support the RC mode in a separate driver and binding. I initially thought about merging both in a single driver & binding but that seemed unnecessarily complex, so settled with this. > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 139 ++++++++++++++++++ > > 1 file changed, 139 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml > > > > diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml > > new file mode 100644 > > index 000000000000..0f9140e93bcb > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml > > @@ -0,0 +1,139 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Qualcomm PCIe Endpoint Controller binding > > + > > +maintainers: > > + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > + > > +allOf: > > + - $ref: "pci-ep.yaml#" > > + > > +properties: > > + compatible: > > + const: qcom,pcie-ep > > SoC specific please. > Okay > > + > > + reg: > > + items: > > + - description: Designware PCIe registers > > + - description: External local bus interface registers > > + - description: Address Translation Unit (ATU) registers > > + - description: Memory region used to map remote RC address space > > + - description: Qualcomm specific PARF configuration registers > > + - description: Qualcomm specific TCSR registers > > + > > + reg-names: > > + items: > > + - const: dbi > > + - const: elbi > > + - const: atu > > + - const: addr_space > > + - const: parf > > + - const: tcsr > > This should be in the same order as the host side. Unfortunately, > that's not consistent, but to pick one: > > reg-names = "parf", "dbi", "elbi", "atu", "config"; > Okay, I'll align with the RC binding. > > > + > > + clocks: > > + items: > > + - description: PCIe CFG AHB clock > > + - description: PCIe Auxiliary clock > > + - description: PCIe Master AXI clock > > + - description: PCIe Slave AXI clock > > + - description: PCIe Reference clock > > + - description: PCIe Sleep clock > > + - description: PCIe Slave Q2A AXI clock > > + > > + clock-names: > > + items: > > + - const: cfg > > + - const: aux > > + - const: bus_master > > + - const: bus_slave > > + - const: ref > > + - const: sleep > > + - const: slave_q2a > > Again, try to keep the same ordering. > > I have to wonder where 'pipe' clock is that most of the QCom > implementations have? > Pipe clock is managed by the PHY driver. So the PCIe drivers need not to worry about it. > > + > > + interrupts: > > + maxItems: 1 > > + description: PCIe Global interrupt > > + > > + interrupt-names: > > + const: int_global > > 'int_' is redundant, drop. > Okay > > + > > + perst-gpios: > > + description: PCIe endpoint reset GPIO > > An input, right? > Yes, will mention. > > + maxItems: 1 > > + > > + wake-gpios: > > + description: PCIe endpoint wake GPIO > > + maxItems: 1 > > + > > + resets: > > + maxItems: 1 > > + > > + reset-names: > > + const: core_reset > > Not yet another name. We already have 'pci' and 'core' in the cases of > a single reset. > Okay > > + > > + power-domains: > > + maxItems: 1 > > + > > + phys: > > + maxItems: 1 > > + > > + phy-names: > > + const: pciephy > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + - clocks > > + - clock-names > > + - interrupts > > + - interrupt-names > > + - perst-gpios > > + - resets > > + - reset-names > > + - power-domains > > + > > +unevaluatedProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/clock/qcom,gcc-sdx55.h> > > + #include <dt-bindings/gpio/gpio.h> > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + pcie_ep: pcie-ep@40000000 { > > + compatible = "qcom,pcie-ep"; > > + > > + reg = <0x40000000 0xf1d>, > > + <0x40000f20 0xc8>, > > + <0x40001000 0x1000>, > > + <0x42000000 0x1000>, > > + <0x01c00000 0x3000>, > > + <0x01fcb000 0x1000>; > > + reg-names = "dbi", "elbi", "atu", "addr_space", "parf", "tcsr"; > > + > > + clocks = <&gcc GCC_PCIE_CFG_AHB_CLK>, > > + <&gcc GCC_PCIE_AUX_CLK>, > > + <&gcc GCC_PCIE_MSTR_AXI_CLK>, > > + <&gcc GCC_PCIE_SLV_AXI_CLK>, > > + <&gcc GCC_PCIE_0_CLKREF_CLK>, > > + <&gcc GCC_PCIE_SLEEP_CLK>, > > + <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>; > > + clock-names = "cfg", "aux", "bus_master", "bus_slave", > > + "ref", "sleep", "slave_q2a"; > > + > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "int_global"; > > + perst-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; > > + wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; > > + resets = <&gcc GCC_PCIE_BCR>; > > + reset-names = "core_reset"; > > + power-domains = <&gcc PCIE_GDSC>; > > + phys = <&pcie0_lane>; > > + phy-names = "pciephy"; > > + max-link-speed = <3>; > > + num-lanes = <2>; > > Should be documented. I'd assume the max is less than 16 which is > presumably what pcie-ep.yaml allows. > okay Thanks, Mani > > + }; > > -- > > 2.25.1 > >
diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml new file mode 100644 index 000000000000..0f9140e93bcb --- /dev/null +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm PCIe Endpoint Controller binding + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +allOf: + - $ref: "pci-ep.yaml#" + +properties: + compatible: + const: qcom,pcie-ep + + reg: + items: + - description: Designware PCIe registers + - description: External local bus interface registers + - description: Address Translation Unit (ATU) registers + - description: Memory region used to map remote RC address space + - description: Qualcomm specific PARF configuration registers + - description: Qualcomm specific TCSR registers + + reg-names: + items: + - const: dbi + - const: elbi + - const: atu + - const: addr_space + - const: parf + - const: tcsr + + clocks: + items: + - description: PCIe CFG AHB clock + - description: PCIe Auxiliary clock + - description: PCIe Master AXI clock + - description: PCIe Slave AXI clock + - description: PCIe Reference clock + - description: PCIe Sleep clock + - description: PCIe Slave Q2A AXI clock + + clock-names: + items: + - const: cfg + - const: aux + - const: bus_master + - const: bus_slave + - const: ref + - const: sleep + - const: slave_q2a + + interrupts: + maxItems: 1 + description: PCIe Global interrupt + + interrupt-names: + const: int_global + + perst-gpios: + description: PCIe endpoint reset GPIO + maxItems: 1 + + wake-gpios: + description: PCIe endpoint wake GPIO + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + const: core_reset + + power-domains: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: pciephy + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - perst-gpios + - resets + - reset-names + - power-domains + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sdx55.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + pcie_ep: pcie-ep@40000000 { + compatible = "qcom,pcie-ep"; + + reg = <0x40000000 0xf1d>, + <0x40000f20 0xc8>, + <0x40001000 0x1000>, + <0x42000000 0x1000>, + <0x01c00000 0x3000>, + <0x01fcb000 0x1000>; + reg-names = "dbi", "elbi", "atu", "addr_space", "parf", "tcsr"; + + clocks = <&gcc GCC_PCIE_CFG_AHB_CLK>, + <&gcc GCC_PCIE_AUX_CLK>, + <&gcc GCC_PCIE_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_SLV_AXI_CLK>, + <&gcc GCC_PCIE_0_CLKREF_CLK>, + <&gcc GCC_PCIE_SLEEP_CLK>, + <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>; + clock-names = "cfg", "aux", "bus_master", "bus_slave", + "ref", "sleep", "slave_q2a"; + + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "int_global"; + perst-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; + wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; + resets = <&gcc GCC_PCIE_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc PCIE_GDSC>; + phys = <&pcie0_lane>; + phy-names = "pciephy"; + max-link-speed = <3>; + num-lanes = <2>; + };
Add devicetree binding for Qualcomm PCIe EP controller used in platforms like SDX55. The EP controller is based on the Designware core with Qualcomm specific wrappers. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 139 ++++++++++++++++++ 1 file changed, 139 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml -- 2.25.1