| Message ID | 1619112931-2144-2-git-send-email-sanm@codeaurora.org |
|---|---|
| State | New |
| Headers | show |
| Series | [v2] arm64: dts: qcom: sc7280: Add USB related nodes | expand |
On Thu, Apr 22, 2021 at 11:05:31PM +0530, Sandeep Maheswaram wrote: > Add nodes for DWC3 USB controller, QMP and HS USB PHYs. > > Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org> > --- What changes with respect to v1? Please always include a change log for versions > 1 > arch/arm64/boot/dts/qcom/sc7280-idp.dts | 40 +++++++++ > arch/arm64/boot/dts/qcom/sc7280.dtsi | 150 ++++++++++++++++++++++++++++++++ > 2 files changed, 190 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts > index 54d2cb3..f1998d8 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts > +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts I suggest to split this into two patches, one for the SoC and one for the board (IDP). That way it is evident from the subject what each patch does and reverts could be done individually if needed. > @@ -242,6 +242,46 @@ > status = "okay"; > }; > > + don't add a second empty line > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "host"; > +}; > + > +&usb_1_hsphy { > + status = "okay"; > + > + vdda-pll-supply = <&vreg_l10c_0p8>; > + vdda33-supply = <&vreg_l2b_3p0>; > + vdda18-supply = <&vreg_l1c_1p8>; > +}; > + > +&usb_1_qmpphy { > + status = "okay"; > + > + vdda-phy-supply = <&vreg_l6b_1p2>; > + vdda-pll-supply = <&vreg_l1b_0p8>; > +}; > + > +&usb_2 { > + status = "okay"; > +}; > + > +&usb_2_dwc3 { > + dr_mode = "peripheral"; > +}; > + > +&usb_2_hsphy { > + status = "okay"; > + > + vdda-pll-supply = <&vreg_l10c_0p8>; > + vdda33-supply = <&vreg_l2b_3p0>; > + vdda18-supply = <&vreg_l1c_1p8>; > +}; > + > /* PINCTRL - additions to nodes defined in sc7280.dtsi */ > > &qup_uart5_default { > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi > index 2cc4785..8323f53 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi > @@ -805,6 +805,110 @@ > }; > }; > > + usb_1_hsphy: phy@88e3000 { > + compatible = "qcom,sc7280-usb-hs-phy", > + "qcom,usb-snps-hs-7nm-phy"; > + reg = <0 0x088e3000 0 0x400>; > + status = "disabled"; > + #phy-cells = <0>; > + > + clocks = <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "ref"; > + > + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; > + }; > + > + usb_2_hsphy: phy@88e4000 { > + compatible = "qcom,sc7280-usb-hs-phy", > + "qcom,usb-snps-hs-7nm-phy"; > + reg = <0 0x088e4000 0 0x400>; > + status = "disabled"; > + #phy-cells = <0>; > + > + clocks = <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "ref"; > + > + resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; > + }; > + > + usb_1_qmpphy: phy-wrapper@88e9000 { > + compatible = "qcom,sm8250-qmp-usb3-phy"; > + reg = <0 0x088e9000 0 0x200>, > + <0 0x088e8000 0 0x20>; > + reg-names = "reg-base", "dp_com"; > + status = "disabled"; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, > + <&rpmhcc RPMH_CXO_CLK>, > + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; > + clock-names = "aux", "ref_clk_src", "com_aux"; > + > + resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>, > + <&gcc GCC_USB3_PHY_PRIM_BCR>; > + reset-names = "phy", "common"; > + > + usb_1_ssphy: usb3-phy@88e9200 { > + reg = <0 0x088e9200 0 0x200>, > + <0 0x088e9400 0 0x200>, > + <0 0x088e9c00 0 0x400>, > + <0 0x088e9600 0 0x200>, > + <0 0x088e9800 0 0x200>, > + <0 0x088e9a00 0 0x100>; > + #phy-cells = <0>; > + #clock-cells = <1>; > + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; > + clock-names = "pipe0"; > + clock-output-names = "usb3_phy_pipe_clk_src"; > + }; > + }; > + > + usb_2: usb@8cf8800 { > + compatible = "qcom,sc7280-dwc3", "qcom,dwc3"; > + reg = <0 0x08cf8800 0 0x400>; > + status = "disabled"; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + dma-ranges; > + > + clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, > + <&gcc GCC_USB30_SEC_MASTER_CLK>, > + <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, > + <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, > + <&gcc GCC_USB30_SEC_SLEEP_CLK>; > + clock-names = "cfg_noc", "core", "iface","mock_utmi", > + "sleep"; > + > + assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, > + <&gcc GCC_USB30_SEC_MASTER_CLK>; > + assigned-clock-rates = <19200000>, <200000000>; > + > + interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>, > + <&pdc 13 IRQ_TYPE_EDGE_RISING>, > + <&pdc 12 IRQ_TYPE_EDGE_RISING>; > + interrupt-names = "hs_phy_irq", > + "dm_hs_phy_irq", "dp_hs_phy_irq"; > + > + power-domains = <&gcc GCC_USB30_SEC_GDSC>; > + > + resets = <&gcc GCC_USB30_SEC_BCR>; > + > + usb_2_dwc3: dwc3@8c00000 { > + compatible = "snps,dwc3"; > + reg = <0 0x08c00000 0 0xe000>; > + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; > + iommus = <&apps_smmu 0xa0 0x0>; > + snps,dis_u2_susphy_quirk; > + snps,dis_enblslpm_quirk; > + phys = <&usb_2_hsphy>; > + phy-names = "usb2-phy"; > + maximum-speed = "high-speed"; > + }; > + }; > + > system-cache-controller@9200000 { > compatible = "qcom,sc7280-llcc"; > reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; > @@ -812,6 +916,52 @@ > interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; > }; > > + usb_1: usb@a6f8800 { > + compatible = "qcom,sc7280-dwc3", "qcom,dwc3"; > + reg = <0 0x0a6f8800 0 0x400>; > + status = "disabled"; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + dma-ranges; > + > + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, > + <&gcc GCC_USB30_PRIM_MASTER_CLK>, > + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, > + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, > + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; > + nit: remove empty line (as for 'usb_2' above), 'clocks' and 'clock-names' belong together > + clock-names = "cfg_noc", "core", "iface", "mock_utmi", > + "sleep"; > + > + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, > + <&gcc GCC_USB30_PRIM_MASTER_CLK>; > + assigned-clock-rates = <19200000>, <200000000>; > + > + interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, > + <&pdc 14 IRQ_TYPE_EDGE_BOTH>, > + <&pdc 15 IRQ_TYPE_EDGE_BOTH>, > + <&pdc 17 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hs_phy_irq", "dp_hs_phy_irq", > + "dm_hs_phy_irq", "ss_phy_irq"; > + > + power-domains = <&gcc GCC_USB30_PRIM_GDSC>; > + > + resets = <&gcc GCC_USB30_PRIM_BCR>; > + > + usb_1_dwc3: dwc3@a600000 { > + compatible = "snps,dwc3"; > + reg = <0 0x0a600000 0 0xe000>; > + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; > + iommus = <&apps_smmu 0xe0 0x0>; > + snps,dis_u2_susphy_quirk; > + snps,dis_enblslpm_quirk; > + phys = <&usb_1_hsphy>, <&usb_1_ssphy>; > + phy-names = "usb2-phy", "usb3-phy"; > + maximum-speed = "super-speed"; > + }; > + }; > + > pdc: interrupt-controller@b220000 { > compatible = "qcom,sc7280-pdc", "qcom,pdc"; > reg = <0 0x0b220000 0 0x30000>;
Hi, On Thu, Apr 22, 2021 at 11:34 AM Matthias Kaehlcke <mka@chromium.org> wrote: > > On Thu, Apr 22, 2021 at 11:05:31PM +0530, Sandeep Maheswaram wrote: > > Add nodes for DWC3 USB controller, QMP and HS USB PHYs. > > > > Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org> > > --- > > What changes with respect to v1? Please always include a change log for > versions > 1 It looks like this was here: https://lore.kernel.org/r/1619112931-2144-1-git-send-email-sanm@codeaurora.org/ ...which I guess is a "cover letter", though it's not really formatted properly (it should usually be listed as "patch 0" in the series) and also cover letters are discouraged for singleton patches like this. Also: even when history is added to a cover letter it's usually friendly to reviewers to also include it after-the-cut in your patch. -Doug
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts index 54d2cb3..f1998d8 100644 --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts @@ -242,6 +242,46 @@ status = "okay"; }; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l10c_0p8>; + vdda33-supply = <&vreg_l2b_3p0>; + vdda18-supply = <&vreg_l1c_1p8>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l6b_1p2>; + vdda-pll-supply = <&vreg_l1b_0p8>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "peripheral"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l10c_0p8>; + vdda33-supply = <&vreg_l2b_3p0>; + vdda18-supply = <&vreg_l1c_1p8>; +}; + /* PINCTRL - additions to nodes defined in sc7280.dtsi */ &qup_uart5_default { diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 2cc4785..8323f53 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -805,6 +805,110 @@ }; }; + usb_1_hsphy: phy@88e3000 { + compatible = "qcom,sc7280-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e3000 0 0x400>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + }; + + usb_2_hsphy: phy@88e4000 { + compatible = "qcom,sc7280-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e4000 0 0x400>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; + }; + + usb_1_qmpphy: phy-wrapper@88e9000 { + compatible = "qcom,sm8250-qmp-usb3-phy"; + reg = <0 0x088e9000 0 0x200>, + <0 0x088e8000 0 0x20>; + reg-names = "reg-base", "dp_com"; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; + clock-names = "aux", "ref_clk_src", "com_aux"; + + resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>, + <&gcc GCC_USB3_PHY_PRIM_BCR>; + reset-names = "phy", "common"; + + usb_1_ssphy: usb3-phy@88e9200 { + reg = <0 0x088e9200 0 0x200>, + <0 0x088e9400 0 0x200>, + <0 0x088e9c00 0 0x400>, + <0 0x088e9600 0 0x200>, + <0 0x088e9800 0 0x200>, + <0 0x088e9a00 0 0x100>; + #phy-cells = <0>; + #clock-cells = <1>; + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_phy_pipe_clk_src"; + }; + }; + + usb_2: usb@8cf8800 { + compatible = "qcom,sc7280-dwc3", "qcom,dwc3"; + reg = <0 0x08cf8800 0 0x400>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, + <&gcc GCC_USB30_SEC_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, + <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SEC_SLEEP_CLK>; + clock-names = "cfg_noc", "core", "iface","mock_utmi", + "sleep"; + + assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SEC_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 13 IRQ_TYPE_EDGE_RISING>, + <&pdc 12 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "hs_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + power-domains = <&gcc GCC_USB30_SEC_GDSC>; + + resets = <&gcc GCC_USB30_SEC_BCR>; + + usb_2_dwc3: dwc3@8c00000 { + compatible = "snps,dwc3"; + reg = <0 0x08c00000 0 0xe000>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0xa0 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_2_hsphy>; + phy-names = "usb2-phy"; + maximum-speed = "high-speed"; + }; + }; + system-cache-controller@9200000 { compatible = "qcom,sc7280-llcc"; reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; @@ -812,6 +916,52 @@ interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; }; + usb_1: usb@a6f8800 { + compatible = "qcom,sc7280-dwc3", "qcom,dwc3"; + reg = <0 0x0a6f8800 0 0x400>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + + clock-names = "cfg_noc", "core", "iface", "mock_utmi", + "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 14 IRQ_TYPE_EDGE_BOTH>, + <&pdc 15 IRQ_TYPE_EDGE_BOTH>, + <&pdc 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hs_phy_irq", "dp_hs_phy_irq", + "dm_hs_phy_irq", "ss_phy_irq"; + + power-domains = <&gcc GCC_USB30_PRIM_GDSC>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + + usb_1_dwc3: dwc3@a600000 { + compatible = "snps,dwc3"; + reg = <0 0x0a600000 0 0xe000>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0xe0 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_1_hsphy>, <&usb_1_ssphy>; + phy-names = "usb2-phy", "usb3-phy"; + maximum-speed = "super-speed"; + }; + }; + pdc: interrupt-controller@b220000 { compatible = "qcom,sc7280-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>;
Add nodes for DWC3 USB controller, QMP and HS USB PHYs. Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org> --- arch/arm64/boot/dts/qcom/sc7280-idp.dts | 40 +++++++++ arch/arm64/boot/dts/qcom/sc7280.dtsi | 150 ++++++++++++++++++++++++++++++++ 2 files changed, 190 insertions(+)