| Message ID | 4d535d35-6c8c-2bd8-812b-2b53194ce0ec@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | PCI: Remove pci_try_set_mwi | expand |
Heiner Kallweit <hkallweit1@gmail.com> writes: > pci_set_mwi() and pci_try_set_mwi() do exactly the same, just that the > former one is declared as __must_check. However also some callers of > pci_set_mwi() have a comment that it's an optional feature. I don't > think there's much sense in this separation and the use of > __must_check. Therefore remove pci_try_set_mwi() and remove the > __must_check attribute from pci_set_mwi(). > I don't expect either function to be used in new code anyway. > > Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> > --- > patch applies on top of pci/misc for v5.11 > drivers/net/wireless/intersil/p54/p54pci.c | 2 +- > .../intersil/prism54/islpci_hotplug.c | 3 +-- > .../wireless/realtek/rtl818x/rtl8180/dev.c | 2 +- For drivers/wireless: Acked-by: Kalle Valo <kvalo@codeaurora.org>
On Wed, 09 Dec 2020, Heiner Kallweit wrote: > pci_set_mwi() and pci_try_set_mwi() do exactly the same, just that the > former one is declared as __must_check. However also some callers of > pci_set_mwi() have a comment that it's an optional feature. I don't > think there's much sense in this separation and the use of > __must_check. Therefore remove pci_try_set_mwi() and remove the > __must_check attribute from pci_set_mwi(). > I don't expect either function to be used in new code anyway. > > Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> > --- > patch applies on top of pci/misc for v5.11 > --- > Documentation/PCI/pci.rst | 5 +---- > drivers/ata/pata_cs5530.c | 2 +- > drivers/ata/sata_mv.c | 2 +- > drivers/dma/dw/pci.c | 2 +- > drivers/dma/hsu/pci.c | 2 +- > drivers/ide/cs5530.c | 2 +- > drivers/mfd/intel-lpss-pci.c | 2 +- Acked-by: Lee Jones <lee.jones@linaro.org> > drivers/net/ethernet/adaptec/starfire.c | 2 +- > drivers/net/ethernet/alacritech/slicoss.c | 2 +- > drivers/net/ethernet/dec/tulip/tulip_core.c | 5 +---- > drivers/net/ethernet/sun/cassini.c | 4 ++-- > drivers/net/wireless/intersil/p54/p54pci.c | 2 +- > .../intersil/prism54/islpci_hotplug.c | 3 +-- > .../wireless/realtek/rtl818x/rtl8180/dev.c | 2 +- > drivers/pci/pci.c | 19 ------------------- > drivers/scsi/3w-9xxx.c | 4 ++-- > drivers/scsi/3w-sas.c | 4 ++-- > drivers/scsi/csiostor/csio_init.c | 2 +- > drivers/scsi/lpfc/lpfc_init.c | 2 +- > drivers/scsi/qla2xxx/qla_init.c | 8 ++++---- > drivers/scsi/qla2xxx/qla_mr.c | 2 +- > drivers/tty/serial/8250/8250_lpss.c | 2 +- > drivers/usb/chipidea/ci_hdrc_pci.c | 2 +- > drivers/usb/gadget/udc/amd5536udc_pci.c | 2 +- > drivers/usb/gadget/udc/net2280.c | 2 +- > drivers/usb/gadget/udc/pch_udc.c | 2 +- > include/linux/pci.h | 5 ++--- > 27 files changed, 33 insertions(+), 60 deletions(-)
On Wed, Dec 9, 2020 at 10:35 AM Heiner Kallweit <hkallweit1@gmail.com> wrote: > pci_set_mwi() and pci_try_set_mwi() do exactly the same, just that the > former one is declared as __must_check. However also some callers of However also -> However > pci_set_mwi() have a comment that it's an optional feature. I don't > think there's much sense in this separation and the use of > __must_check. Therefore remove pci_try_set_mwi() and remove the > __must_check attribute from pci_set_mwi(). > I don't expect either function to be used in new code anyway. You probably want to elaborate here that the feature is specific to PCI and isn't present on PCIe. Besides that one comment below. After addressing, have my Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> for the files left in this message. ... > drivers/dma/dw/pci.c | 2 +- > drivers/dma/hsu/pci.c | 2 +- > drivers/mfd/intel-lpss-pci.c | 2 +- > drivers/pci/pci.c | 19 ------------------- > drivers/tty/serial/8250/8250_lpss.c | 2 +- > drivers/usb/chipidea/ci_hdrc_pci.c | 2 +- > drivers/usb/gadget/udc/pch_udc.c | 2 +- > include/linux/pci.h | 5 ++--- > diff --git a/Documentation/PCI/pci.rst b/Documentation/PCI/pci.rst > index 814b40f83..120362cc9 100644 > --- a/Documentation/PCI/pci.rst > +++ b/Documentation/PCI/pci.rst > @@ -226,10 +226,7 @@ If the PCI device can use the PCI Memory-Write-Invalidate transaction, > call pci_set_mwi(). This enables the PCI_COMMAND bit for Mem-Wr-Inval > and also ensures that the cache line size register is set correctly. > Check the return value of pci_set_mwi() as not all architectures > -or chip-sets may support Memory-Write-Invalidate. Alternatively, > -if Mem-Wr-Inval would be nice to have but is not required, call > -pci_try_set_mwi() to have the system do its best effort at enabling > -Mem-Wr-Inval. > +or chip-sets may support Memory-Write-Invalidate. ... > diff --git a/drivers/dma/dw/pci.c b/drivers/dma/dw/pci.c > index 1142aa6f8..1c20b7485 100644 > --- a/drivers/dma/dw/pci.c > +++ b/drivers/dma/dw/pci.c > @@ -30,7 +30,7 @@ static int dw_pci_probe(struct pci_dev *pdev, const struct pci_device_id *pid) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); > if (ret) > diff --git a/drivers/dma/hsu/pci.c b/drivers/dma/hsu/pci.c > index 07cc7320a..420dd3706 100644 > --- a/drivers/dma/hsu/pci.c > +++ b/drivers/dma/hsu/pci.c > @@ -73,7 +73,7 @@ static int hsu_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); > if (ret) ... > diff --git a/drivers/mfd/intel-lpss-pci.c b/drivers/mfd/intel-lpss-pci.c > index 2d7c588ef..a0c3be750 100644 > --- a/drivers/mfd/intel-lpss-pci.c > +++ b/drivers/mfd/intel-lpss-pci.c > @@ -39,7 +39,7 @@ static int intel_lpss_pci_probe(struct pci_dev *pdev, > > /* Probably it is enough to set this for iDMA capable devices only */ > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > ret = intel_lpss_probe(&pdev->dev, info); > if (ret) ... > diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c > index 9a5500287..f0ab432d2 100644 > --- a/drivers/pci/pci.c > +++ b/drivers/pci/pci.c > @@ -4389,25 +4389,6 @@ int pcim_set_mwi(struct pci_dev *dev) > } > EXPORT_SYMBOL(pcim_set_mwi); > > -/** > - * pci_try_set_mwi - enables memory-write-invalidate PCI transaction > - * @dev: the PCI device for which MWI is enabled > - * > - * Enables the Memory-Write-Invalidate transaction in %PCI_COMMAND. > - * Callers are not required to check the return value. > - * > - * RETURNS: An appropriate -ERRNO error value on error, or zero for success. > - */ > -int pci_try_set_mwi(struct pci_dev *dev) > -{ > -#ifdef PCI_DISABLE_MWI > - return 0; > -#else > - return pci_set_mwi(dev); > -#endif This seems still valid case for PowerPC and SH. > -} > -EXPORT_SYMBOL(pci_try_set_mwi); ... > diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c > index 4dee8a9e0..8acc1e5c9 100644 > --- a/drivers/tty/serial/8250/8250_lpss.c > +++ b/drivers/tty/serial/8250/8250_lpss.c > @@ -193,7 +193,7 @@ static void qrk_serial_setup_dma(struct lpss8250 *lpss, struct uart_port *port) > if (ret) > return; > > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* Special DMA address for UART */ > dma->rx_dma_addr = 0xfffff000; > diff --git a/drivers/usb/chipidea/ci_hdrc_pci.c b/drivers/usb/chipidea/ci_hdrc_pci.c > index d63479e1a..d412fa910 100644 > --- a/drivers/usb/chipidea/ci_hdrc_pci.c > +++ b/drivers/usb/chipidea/ci_hdrc_pci.c > @@ -78,7 +78,7 @@ static int ci_hdrc_pci_probe(struct pci_dev *pdev, > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* register a nop PHY */ > ci->phy = usb_phy_generic_register(); ... > diff --git a/drivers/usb/gadget/udc/pch_udc.c b/drivers/usb/gadget/udc/pch_udc.c > index a3c1fc924..4a0484a0c 100644 > --- a/drivers/usb/gadget/udc/pch_udc.c > +++ b/drivers/usb/gadget/udc/pch_udc.c > @@ -3100,7 +3100,7 @@ static int pch_udc_probe(struct pci_dev *pdev, > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* device struct setup */ > spin_lock_init(&dev->lock); > diff --git a/include/linux/pci.h b/include/linux/pci.h > index de75f6a4d..c590f616d 100644 > --- a/include/linux/pci.h > +++ b/include/linux/pci.h > @@ -1191,9 +1191,8 @@ void pci_clear_master(struct pci_dev *dev); > > int pci_set_pcie_reset_state(struct pci_dev *dev, enum pcie_reset_state state); > int pci_set_cacheline_size(struct pci_dev *dev); > -int __must_check pci_set_mwi(struct pci_dev *dev); > -int __must_check pcim_set_mwi(struct pci_dev *dev); > -int pci_try_set_mwi(struct pci_dev *dev); > +int pci_set_mwi(struct pci_dev *dev); > +int pcim_set_mwi(struct pci_dev *dev); > void pci_clear_mwi(struct pci_dev *dev); > void pci_intx(struct pci_dev *dev, int enable); > bool pci_check_and_mask_intx(struct pci_dev *dev);
[+cc Randy, Andrew (though I'm sure you have zero interest in this ancient question :))] On Wed, Dec 09, 2020 at 09:31:21AM +0100, Heiner Kallweit wrote: > pci_set_mwi() and pci_try_set_mwi() do exactly the same, just that the > former one is declared as __must_check. However also some callers of > pci_set_mwi() have a comment that it's an optional feature. I don't > think there's much sense in this separation and the use of > __must_check. Therefore remove pci_try_set_mwi() and remove the > __must_check attribute from pci_set_mwi(). > I don't expect either function to be used in new code anyway. There's not much I like better than removing things. But some significant thought went into adding pci_try_set_mwi() in the first place, so I need a little more convincing about why it's safe to remove it. The argument should cite the discussion about adding it. I think one of the earliest conversations is here: https://lore.kernel.org/linux-ide/20070404213704.224128ec.randy.dunlap@oracle.com/ > Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> > --- > patch applies on top of pci/misc for v5.11 > --- > Documentation/PCI/pci.rst | 5 +---- > drivers/ata/pata_cs5530.c | 2 +- > drivers/ata/sata_mv.c | 2 +- > drivers/dma/dw/pci.c | 2 +- > drivers/dma/hsu/pci.c | 2 +- > drivers/ide/cs5530.c | 2 +- > drivers/mfd/intel-lpss-pci.c | 2 +- > drivers/net/ethernet/adaptec/starfire.c | 2 +- > drivers/net/ethernet/alacritech/slicoss.c | 2 +- > drivers/net/ethernet/dec/tulip/tulip_core.c | 5 +---- > drivers/net/ethernet/sun/cassini.c | 4 ++-- > drivers/net/wireless/intersil/p54/p54pci.c | 2 +- > .../intersil/prism54/islpci_hotplug.c | 3 +-- > .../wireless/realtek/rtl818x/rtl8180/dev.c | 2 +- > drivers/pci/pci.c | 19 ------------------- > drivers/scsi/3w-9xxx.c | 4 ++-- > drivers/scsi/3w-sas.c | 4 ++-- > drivers/scsi/csiostor/csio_init.c | 2 +- > drivers/scsi/lpfc/lpfc_init.c | 2 +- > drivers/scsi/qla2xxx/qla_init.c | 8 ++++---- > drivers/scsi/qla2xxx/qla_mr.c | 2 +- > drivers/tty/serial/8250/8250_lpss.c | 2 +- > drivers/usb/chipidea/ci_hdrc_pci.c | 2 +- > drivers/usb/gadget/udc/amd5536udc_pci.c | 2 +- > drivers/usb/gadget/udc/net2280.c | 2 +- > drivers/usb/gadget/udc/pch_udc.c | 2 +- > include/linux/pci.h | 5 ++--- > 27 files changed, 33 insertions(+), 60 deletions(-) > > diff --git a/Documentation/PCI/pci.rst b/Documentation/PCI/pci.rst > index 814b40f83..120362cc9 100644 > --- a/Documentation/PCI/pci.rst > +++ b/Documentation/PCI/pci.rst > @@ -226,10 +226,7 @@ If the PCI device can use the PCI Memory-Write-Invalidate transaction, > call pci_set_mwi(). This enables the PCI_COMMAND bit for Mem-Wr-Inval > and also ensures that the cache line size register is set correctly. > Check the return value of pci_set_mwi() as not all architectures > -or chip-sets may support Memory-Write-Invalidate. Alternatively, > -if Mem-Wr-Inval would be nice to have but is not required, call > -pci_try_set_mwi() to have the system do its best effort at enabling > -Mem-Wr-Inval. > +or chip-sets may support Memory-Write-Invalidate. > > > Request MMIO/IOP resources > diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c > index ad75d02b6..8654b3ae1 100644 > --- a/drivers/ata/pata_cs5530.c > +++ b/drivers/ata/pata_cs5530.c > @@ -214,7 +214,7 @@ static int cs5530_init_chip(void) > } > > pci_set_master(cs5530_0); > - pci_try_set_mwi(cs5530_0); > + pci_set_mwi(cs5530_0); > > /* > * Set PCI CacheLineSize to 16-bytes: > diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c > index 664ef658a..ee37755ea 100644 > --- a/drivers/ata/sata_mv.c > +++ b/drivers/ata/sata_mv.c > @@ -4432,7 +4432,7 @@ static int mv_pci_init_one(struct pci_dev *pdev, > mv_print_info(host); > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED, > IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht); > } > diff --git a/drivers/dma/dw/pci.c b/drivers/dma/dw/pci.c > index 1142aa6f8..1c20b7485 100644 > --- a/drivers/dma/dw/pci.c > +++ b/drivers/dma/dw/pci.c > @@ -30,7 +30,7 @@ static int dw_pci_probe(struct pci_dev *pdev, const struct pci_device_id *pid) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); > if (ret) > diff --git a/drivers/dma/hsu/pci.c b/drivers/dma/hsu/pci.c > index 07cc7320a..420dd3706 100644 > --- a/drivers/dma/hsu/pci.c > +++ b/drivers/dma/hsu/pci.c > @@ -73,7 +73,7 @@ static int hsu_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); > if (ret) > diff --git a/drivers/ide/cs5530.c b/drivers/ide/cs5530.c > index 5bb46e713..5d2c421ab 100644 > --- a/drivers/ide/cs5530.c > +++ b/drivers/ide/cs5530.c > @@ -168,7 +168,7 @@ static int init_chipset_cs5530(struct pci_dev *dev) > */ > > pci_set_master(cs5530_0); > - pci_try_set_mwi(cs5530_0); > + pci_set_mwi(cs5530_0); > > /* > * Set PCI CacheLineSize to 16-bytes: > diff --git a/drivers/mfd/intel-lpss-pci.c b/drivers/mfd/intel-lpss-pci.c > index 2d7c588ef..a0c3be750 100644 > --- a/drivers/mfd/intel-lpss-pci.c > +++ b/drivers/mfd/intel-lpss-pci.c > @@ -39,7 +39,7 @@ static int intel_lpss_pci_probe(struct pci_dev *pdev, > > /* Probably it is enough to set this for iDMA capable devices only */ > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > ret = intel_lpss_probe(&pdev->dev, info); > if (ret) > diff --git a/drivers/net/ethernet/adaptec/starfire.c b/drivers/net/ethernet/adaptec/starfire.c > index 555299737..1dbff34c4 100644 > --- a/drivers/net/ethernet/adaptec/starfire.c > +++ b/drivers/net/ethernet/adaptec/starfire.c > @@ -679,7 +679,7 @@ static int starfire_init_one(struct pci_dev *pdev, > pci_set_master(pdev); > > /* enable MWI -- it vastly improves Rx performance on sparc64 */ > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > #ifdef ZEROCOPY > /* Starfire can do TCP/UDP checksumming */ > diff --git a/drivers/net/ethernet/alacritech/slicoss.c b/drivers/net/ethernet/alacritech/slicoss.c > index 696517eae..544510f57 100644 > --- a/drivers/net/ethernet/alacritech/slicoss.c > +++ b/drivers/net/ethernet/alacritech/slicoss.c > @@ -1749,7 +1749,7 @@ static int slic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > slic_configure_pci(pdev); > > diff --git a/drivers/net/ethernet/dec/tulip/tulip_core.c b/drivers/net/ethernet/dec/tulip/tulip_core.c > index c1dcd6ca1..4f6debb24 100644 > --- a/drivers/net/ethernet/dec/tulip/tulip_core.c > +++ b/drivers/net/ethernet/dec/tulip/tulip_core.c > @@ -1193,10 +1193,7 @@ static void tulip_mwi_config(struct pci_dev *pdev, struct net_device *dev) > /* if we have any cache line size at all, we can do MRM and MWI */ > csr0 |= MRM | MWI; > > - /* Enable MWI in the standard PCI command bit. > - * Check for the case where MWI is desired but not available > - */ > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* read result from hardware (in case bit refused to enable) */ > pci_read_config_word(pdev, PCI_COMMAND, &pci_command); > diff --git a/drivers/net/ethernet/sun/cassini.c b/drivers/net/ethernet/sun/cassini.c > index 9ff894ba8..9a95ec989 100644 > --- a/drivers/net/ethernet/sun/cassini.c > +++ b/drivers/net/ethernet/sun/cassini.c > @@ -4933,14 +4933,14 @@ static int cas_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) > pci_cmd &= ~PCI_COMMAND_SERR; > pci_cmd |= PCI_COMMAND_PARITY; > pci_write_config_word(pdev, PCI_COMMAND, pci_cmd); > - if (pci_try_set_mwi(pdev)) > + if (pci_set_mwi(pdev)) > pr_warn("Could not enable MWI for %s\n", pci_name(pdev)); > > cas_program_bridge(pdev); > > /* > * On some architectures, the default cache line size set > - * by pci_try_set_mwi reduces perforamnce. We have to increase > + * by pci_set_mwi reduces performance. We have to increase > * it for this case. To start, we'll print some configuration > * data. > */ > diff --git a/drivers/net/wireless/intersil/p54/p54pci.c b/drivers/net/wireless/intersil/p54/p54pci.c > index e97ee547b..c76326d1e 100644 > --- a/drivers/net/wireless/intersil/p54/p54pci.c > +++ b/drivers/net/wireless/intersil/p54/p54pci.c > @@ -583,7 +583,7 @@ static int p54p_probe(struct pci_dev *pdev, > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > pci_write_config_byte(pdev, 0x40, 0); > pci_write_config_byte(pdev, 0x41, 0); > diff --git a/drivers/net/wireless/intersil/prism54/islpci_hotplug.c b/drivers/net/wireless/intersil/prism54/islpci_hotplug.c > index 31a1e6132..e8087d9a5 100644 > --- a/drivers/net/wireless/intersil/prism54/islpci_hotplug.c > +++ b/drivers/net/wireless/intersil/prism54/islpci_hotplug.c > @@ -153,8 +153,7 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id) > DEBUG(SHOW_TRACING, "%s: pci_set_master(pdev)\n", DRV_NAME); > pci_set_master(pdev); > > - /* enable MWI */ > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* setup the network device interface and its structure */ > if (!(ndev = islpci_setup(pdev))) { > diff --git a/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c b/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c > index 2477e18c7..b259b0b58 100644 > --- a/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c > +++ b/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c > @@ -1871,7 +1871,7 @@ static int rtl8180_probe(struct pci_dev *pdev, > > if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { > priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > } > > if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) > diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c > index 9a5500287..f0ab432d2 100644 > --- a/drivers/pci/pci.c > +++ b/drivers/pci/pci.c > @@ -4389,25 +4389,6 @@ int pcim_set_mwi(struct pci_dev *dev) > } > EXPORT_SYMBOL(pcim_set_mwi); > > -/** > - * pci_try_set_mwi - enables memory-write-invalidate PCI transaction > - * @dev: the PCI device for which MWI is enabled > - * > - * Enables the Memory-Write-Invalidate transaction in %PCI_COMMAND. > - * Callers are not required to check the return value. > - * > - * RETURNS: An appropriate -ERRNO error value on error, or zero for success. > - */ > -int pci_try_set_mwi(struct pci_dev *dev) > -{ > -#ifdef PCI_DISABLE_MWI > - return 0; > -#else > - return pci_set_mwi(dev); > -#endif > -} > -EXPORT_SYMBOL(pci_try_set_mwi); > - > /** > * pci_clear_mwi - disables Memory-Write-Invalidate for device dev > * @dev: the PCI device to disable > diff --git a/drivers/scsi/3w-9xxx.c b/drivers/scsi/3w-9xxx.c > index b4718a1b2..d869485e2 100644 > --- a/drivers/scsi/3w-9xxx.c > +++ b/drivers/scsi/3w-9xxx.c > @@ -2018,7 +2018,7 @@ static int twa_probe(struct pci_dev *pdev, const struct pci_device_id *dev_id) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); > if (retval) > @@ -2227,7 +2227,7 @@ static int __maybe_unused twa_resume(struct device *dev) > > printk(KERN_WARNING "3w-9xxx: Resuming host %d.\n", tw_dev->host->host_no); > > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); > if (retval) > diff --git a/drivers/scsi/3w-sas.c b/drivers/scsi/3w-sas.c > index b8f1848ec..49ca153b8 100644 > --- a/drivers/scsi/3w-sas.c > +++ b/drivers/scsi/3w-sas.c > @@ -1571,7 +1571,7 @@ static int twl_probe(struct pci_dev *pdev, const struct pci_device_id *dev_id) > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); > if (retval) > @@ -1790,7 +1790,7 @@ static int __maybe_unused twl_resume(struct device *dev) > TW_Device_Extension *tw_dev = (TW_Device_Extension *)host->hostdata; > > printk(KERN_WARNING "3w-sas: Resuming host %d.\n", tw_dev->host->host_no); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); > if (retval) > diff --git a/drivers/scsi/csiostor/csio_init.c b/drivers/scsi/csiostor/csio_init.c > index 390b07bf9..c20bf44c6 100644 > --- a/drivers/scsi/csiostor/csio_init.c > +++ b/drivers/scsi/csiostor/csio_init.c > @@ -201,7 +201,7 @@ csio_pci_init(struct pci_dev *pdev, int *bars) > goto err_disable_device; > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > rv = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); > if (rv) > diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c > index ac67f420e..b4833c0f8 100644 > --- a/drivers/scsi/lpfc/lpfc_init.c > +++ b/drivers/scsi/lpfc/lpfc_init.c > @@ -6119,7 +6119,7 @@ lpfc_enable_pci_dev(struct lpfc_hba *phba) > goto out_disable_device; > /* Set up device as PCI master and save state for EEH */ > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > pci_save_state(pdev); > > /* PCIe EEH recovery on powerpc platforms needs fundamental reset */ > diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c > index 5626e9b69..76019dc2e 100644 > --- a/drivers/scsi/qla2xxx/qla_init.c > +++ b/drivers/scsi/qla2xxx/qla_init.c > @@ -2356,7 +2356,7 @@ qla2100_pci_config(scsi_qla_host_t *vha) > struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; > > pci_set_master(ha->pdev); > - pci_try_set_mwi(ha->pdev); > + pci_set_mwi(ha->pdev); > > pci_read_config_word(ha->pdev, PCI_COMMAND, &w); > w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); > @@ -2388,7 +2388,7 @@ qla2300_pci_config(scsi_qla_host_t *vha) > struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; > > pci_set_master(ha->pdev); > - pci_try_set_mwi(ha->pdev); > + pci_set_mwi(ha->pdev); > > pci_read_config_word(ha->pdev, PCI_COMMAND, &w); > w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); > @@ -2469,7 +2469,7 @@ qla24xx_pci_config(scsi_qla_host_t *vha) > struct device_reg_24xx __iomem *reg = &ha->iobase->isp24; > > pci_set_master(ha->pdev); > - pci_try_set_mwi(ha->pdev); > + pci_set_mwi(ha->pdev); > > pci_read_config_word(ha->pdev, PCI_COMMAND, &w); > w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); > @@ -2511,7 +2511,7 @@ qla25xx_pci_config(scsi_qla_host_t *vha) > struct qla_hw_data *ha = vha->hw; > > pci_set_master(ha->pdev); > - pci_try_set_mwi(ha->pdev); > + pci_set_mwi(ha->pdev); > > pci_read_config_word(ha->pdev, PCI_COMMAND, &w); > w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); > diff --git a/drivers/scsi/qla2xxx/qla_mr.c b/drivers/scsi/qla2xxx/qla_mr.c > index ca7306685..e9763d8e3 100644 > --- a/drivers/scsi/qla2xxx/qla_mr.c > +++ b/drivers/scsi/qla2xxx/qla_mr.c > @@ -499,7 +499,7 @@ qlafx00_pci_config(scsi_qla_host_t *vha) > struct qla_hw_data *ha = vha->hw; > > pci_set_master(ha->pdev); > - pci_try_set_mwi(ha->pdev); > + pci_set_mwi(ha->pdev); > > pci_read_config_word(ha->pdev, PCI_COMMAND, &w); > w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); > diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c > index 4dee8a9e0..8acc1e5c9 100644 > --- a/drivers/tty/serial/8250/8250_lpss.c > +++ b/drivers/tty/serial/8250/8250_lpss.c > @@ -193,7 +193,7 @@ static void qrk_serial_setup_dma(struct lpss8250 *lpss, struct uart_port *port) > if (ret) > return; > > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* Special DMA address for UART */ > dma->rx_dma_addr = 0xfffff000; > diff --git a/drivers/usb/chipidea/ci_hdrc_pci.c b/drivers/usb/chipidea/ci_hdrc_pci.c > index d63479e1a..d412fa910 100644 > --- a/drivers/usb/chipidea/ci_hdrc_pci.c > +++ b/drivers/usb/chipidea/ci_hdrc_pci.c > @@ -78,7 +78,7 @@ static int ci_hdrc_pci_probe(struct pci_dev *pdev, > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* register a nop PHY */ > ci->phy = usb_phy_generic_register(); > diff --git a/drivers/usb/gadget/udc/amd5536udc_pci.c b/drivers/usb/gadget/udc/amd5536udc_pci.c > index 8d387e0e4..9630ce8d3 100644 > --- a/drivers/usb/gadget/udc/amd5536udc_pci.c > +++ b/drivers/usb/gadget/udc/amd5536udc_pci.c > @@ -151,7 +151,7 @@ static int udc_pci_probe( > dev->chiprev = pdev->revision; > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* init dma pools */ > if (use_dma) { > diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c > index fc9f99fe7..e15520698 100644 > --- a/drivers/usb/gadget/udc/net2280.c > +++ b/drivers/usb/gadget/udc/net2280.c > @@ -3761,7 +3761,7 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id) > &dev->pci->pcimstctl); > /* erratum 0115 shouldn't appear: Linux inits PCI_LATENCY_TIMER */ > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* ... also flushes any posted pci writes */ > dev->chiprev = get_idx_reg(dev->regs, REG_CHIPREV) & 0xffff; > diff --git a/drivers/usb/gadget/udc/pch_udc.c b/drivers/usb/gadget/udc/pch_udc.c > index a3c1fc924..4a0484a0c 100644 > --- a/drivers/usb/gadget/udc/pch_udc.c > +++ b/drivers/usb/gadget/udc/pch_udc.c > @@ -3100,7 +3100,7 @@ static int pch_udc_probe(struct pci_dev *pdev, > } > > pci_set_master(pdev); > - pci_try_set_mwi(pdev); > + pci_set_mwi(pdev); > > /* device struct setup */ > spin_lock_init(&dev->lock); > diff --git a/include/linux/pci.h b/include/linux/pci.h > index de75f6a4d..c590f616d 100644 > --- a/include/linux/pci.h > +++ b/include/linux/pci.h > @@ -1191,9 +1191,8 @@ void pci_clear_master(struct pci_dev *dev); > > int pci_set_pcie_reset_state(struct pci_dev *dev, enum pcie_reset_state state); > int pci_set_cacheline_size(struct pci_dev *dev); > -int __must_check pci_set_mwi(struct pci_dev *dev); > -int __must_check pcim_set_mwi(struct pci_dev *dev); > -int pci_try_set_mwi(struct pci_dev *dev); > +int pci_set_mwi(struct pci_dev *dev); > +int pcim_set_mwi(struct pci_dev *dev); > void pci_clear_mwi(struct pci_dev *dev); > void pci_intx(struct pci_dev *dev, int enable); > bool pci_check_and_mask_intx(struct pci_dev *dev); > -- > 2.29.2 >
diff --git a/Documentation/PCI/pci.rst b/Documentation/PCI/pci.rst index 814b40f83..120362cc9 100644 --- a/Documentation/PCI/pci.rst +++ b/Documentation/PCI/pci.rst @@ -226,10 +226,7 @@ If the PCI device can use the PCI Memory-Write-Invalidate transaction, call pci_set_mwi(). This enables the PCI_COMMAND bit for Mem-Wr-Inval and also ensures that the cache line size register is set correctly. Check the return value of pci_set_mwi() as not all architectures -or chip-sets may support Memory-Write-Invalidate. Alternatively, -if Mem-Wr-Inval would be nice to have but is not required, call -pci_try_set_mwi() to have the system do its best effort at enabling -Mem-Wr-Inval. +or chip-sets may support Memory-Write-Invalidate. Request MMIO/IOP resources diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c index ad75d02b6..8654b3ae1 100644 --- a/drivers/ata/pata_cs5530.c +++ b/drivers/ata/pata_cs5530.c @@ -214,7 +214,7 @@ static int cs5530_init_chip(void) } pci_set_master(cs5530_0); - pci_try_set_mwi(cs5530_0); + pci_set_mwi(cs5530_0); /* * Set PCI CacheLineSize to 16-bytes: diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 664ef658a..ee37755ea 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -4432,7 +4432,7 @@ static int mv_pci_init_one(struct pci_dev *pdev, mv_print_info(host); pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED, IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht); } diff --git a/drivers/dma/dw/pci.c b/drivers/dma/dw/pci.c index 1142aa6f8..1c20b7485 100644 --- a/drivers/dma/dw/pci.c +++ b/drivers/dma/dw/pci.c @@ -30,7 +30,7 @@ static int dw_pci_probe(struct pci_dev *pdev, const struct pci_device_id *pid) } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); if (ret) diff --git a/drivers/dma/hsu/pci.c b/drivers/dma/hsu/pci.c index 07cc7320a..420dd3706 100644 --- a/drivers/dma/hsu/pci.c +++ b/drivers/dma/hsu/pci.c @@ -73,7 +73,7 @@ static int hsu_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); if (ret) diff --git a/drivers/ide/cs5530.c b/drivers/ide/cs5530.c index 5bb46e713..5d2c421ab 100644 --- a/drivers/ide/cs5530.c +++ b/drivers/ide/cs5530.c @@ -168,7 +168,7 @@ static int init_chipset_cs5530(struct pci_dev *dev) */ pci_set_master(cs5530_0); - pci_try_set_mwi(cs5530_0); + pci_set_mwi(cs5530_0); /* * Set PCI CacheLineSize to 16-bytes: diff --git a/drivers/mfd/intel-lpss-pci.c b/drivers/mfd/intel-lpss-pci.c index 2d7c588ef..a0c3be750 100644 --- a/drivers/mfd/intel-lpss-pci.c +++ b/drivers/mfd/intel-lpss-pci.c @@ -39,7 +39,7 @@ static int intel_lpss_pci_probe(struct pci_dev *pdev, /* Probably it is enough to set this for iDMA capable devices only */ pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); ret = intel_lpss_probe(&pdev->dev, info); if (ret) diff --git a/drivers/net/ethernet/adaptec/starfire.c b/drivers/net/ethernet/adaptec/starfire.c index 555299737..1dbff34c4 100644 --- a/drivers/net/ethernet/adaptec/starfire.c +++ b/drivers/net/ethernet/adaptec/starfire.c @@ -679,7 +679,7 @@ static int starfire_init_one(struct pci_dev *pdev, pci_set_master(pdev); /* enable MWI -- it vastly improves Rx performance on sparc64 */ - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); #ifdef ZEROCOPY /* Starfire can do TCP/UDP checksumming */ diff --git a/drivers/net/ethernet/alacritech/slicoss.c b/drivers/net/ethernet/alacritech/slicoss.c index 696517eae..544510f57 100644 --- a/drivers/net/ethernet/alacritech/slicoss.c +++ b/drivers/net/ethernet/alacritech/slicoss.c @@ -1749,7 +1749,7 @@ static int slic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); slic_configure_pci(pdev); diff --git a/drivers/net/ethernet/dec/tulip/tulip_core.c b/drivers/net/ethernet/dec/tulip/tulip_core.c index c1dcd6ca1..4f6debb24 100644 --- a/drivers/net/ethernet/dec/tulip/tulip_core.c +++ b/drivers/net/ethernet/dec/tulip/tulip_core.c @@ -1193,10 +1193,7 @@ static void tulip_mwi_config(struct pci_dev *pdev, struct net_device *dev) /* if we have any cache line size at all, we can do MRM and MWI */ csr0 |= MRM | MWI; - /* Enable MWI in the standard PCI command bit. - * Check for the case where MWI is desired but not available - */ - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* read result from hardware (in case bit refused to enable) */ pci_read_config_word(pdev, PCI_COMMAND, &pci_command); diff --git a/drivers/net/ethernet/sun/cassini.c b/drivers/net/ethernet/sun/cassini.c index 9ff894ba8..9a95ec989 100644 --- a/drivers/net/ethernet/sun/cassini.c +++ b/drivers/net/ethernet/sun/cassini.c @@ -4933,14 +4933,14 @@ static int cas_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) pci_cmd &= ~PCI_COMMAND_SERR; pci_cmd |= PCI_COMMAND_PARITY; pci_write_config_word(pdev, PCI_COMMAND, pci_cmd); - if (pci_try_set_mwi(pdev)) + if (pci_set_mwi(pdev)) pr_warn("Could not enable MWI for %s\n", pci_name(pdev)); cas_program_bridge(pdev); /* * On some architectures, the default cache line size set - * by pci_try_set_mwi reduces perforamnce. We have to increase + * by pci_set_mwi reduces performance. We have to increase * it for this case. To start, we'll print some configuration * data. */ diff --git a/drivers/net/wireless/intersil/p54/p54pci.c b/drivers/net/wireless/intersil/p54/p54pci.c index e97ee547b..c76326d1e 100644 --- a/drivers/net/wireless/intersil/p54/p54pci.c +++ b/drivers/net/wireless/intersil/p54/p54pci.c @@ -583,7 +583,7 @@ static int p54p_probe(struct pci_dev *pdev, } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); pci_write_config_byte(pdev, 0x40, 0); pci_write_config_byte(pdev, 0x41, 0); diff --git a/drivers/net/wireless/intersil/prism54/islpci_hotplug.c b/drivers/net/wireless/intersil/prism54/islpci_hotplug.c index 31a1e6132..e8087d9a5 100644 --- a/drivers/net/wireless/intersil/prism54/islpci_hotplug.c +++ b/drivers/net/wireless/intersil/prism54/islpci_hotplug.c @@ -153,8 +153,7 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id) DEBUG(SHOW_TRACING, "%s: pci_set_master(pdev)\n", DRV_NAME); pci_set_master(pdev); - /* enable MWI */ - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* setup the network device interface and its structure */ if (!(ndev = islpci_setup(pdev))) { diff --git a/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c b/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c index 2477e18c7..b259b0b58 100644 --- a/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c +++ b/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c @@ -1871,7 +1871,7 @@ static int rtl8180_probe(struct pci_dev *pdev, if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); } if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index 9a5500287..f0ab432d2 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -4389,25 +4389,6 @@ int pcim_set_mwi(struct pci_dev *dev) } EXPORT_SYMBOL(pcim_set_mwi); -/** - * pci_try_set_mwi - enables memory-write-invalidate PCI transaction - * @dev: the PCI device for which MWI is enabled - * - * Enables the Memory-Write-Invalidate transaction in %PCI_COMMAND. - * Callers are not required to check the return value. - * - * RETURNS: An appropriate -ERRNO error value on error, or zero for success. - */ -int pci_try_set_mwi(struct pci_dev *dev) -{ -#ifdef PCI_DISABLE_MWI - return 0; -#else - return pci_set_mwi(dev); -#endif -} -EXPORT_SYMBOL(pci_try_set_mwi); - /** * pci_clear_mwi - disables Memory-Write-Invalidate for device dev * @dev: the PCI device to disable diff --git a/drivers/scsi/3w-9xxx.c b/drivers/scsi/3w-9xxx.c index b4718a1b2..d869485e2 100644 --- a/drivers/scsi/3w-9xxx.c +++ b/drivers/scsi/3w-9xxx.c @@ -2018,7 +2018,7 @@ static int twa_probe(struct pci_dev *pdev, const struct pci_device_id *dev_id) } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); if (retval) @@ -2227,7 +2227,7 @@ static int __maybe_unused twa_resume(struct device *dev) printk(KERN_WARNING "3w-9xxx: Resuming host %d.\n", tw_dev->host->host_no); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); if (retval) diff --git a/drivers/scsi/3w-sas.c b/drivers/scsi/3w-sas.c index b8f1848ec..49ca153b8 100644 --- a/drivers/scsi/3w-sas.c +++ b/drivers/scsi/3w-sas.c @@ -1571,7 +1571,7 @@ static int twl_probe(struct pci_dev *pdev, const struct pci_device_id *dev_id) } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); if (retval) @@ -1790,7 +1790,7 @@ static int __maybe_unused twl_resume(struct device *dev) TW_Device_Extension *tw_dev = (TW_Device_Extension *)host->hostdata; printk(KERN_WARNING "3w-sas: Resuming host %d.\n", tw_dev->host->host_no); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); retval = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); if (retval) diff --git a/drivers/scsi/csiostor/csio_init.c b/drivers/scsi/csiostor/csio_init.c index 390b07bf9..c20bf44c6 100644 --- a/drivers/scsi/csiostor/csio_init.c +++ b/drivers/scsi/csiostor/csio_init.c @@ -201,7 +201,7 @@ csio_pci_init(struct pci_dev *pdev, int *bars) goto err_disable_device; pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); rv = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); if (rv) diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index ac67f420e..b4833c0f8 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -6119,7 +6119,7 @@ lpfc_enable_pci_dev(struct lpfc_hba *phba) goto out_disable_device; /* Set up device as PCI master and save state for EEH */ pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); pci_save_state(pdev); /* PCIe EEH recovery on powerpc platforms needs fundamental reset */ diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c index 5626e9b69..76019dc2e 100644 --- a/drivers/scsi/qla2xxx/qla_init.c +++ b/drivers/scsi/qla2xxx/qla_init.c @@ -2356,7 +2356,7 @@ qla2100_pci_config(scsi_qla_host_t *vha) struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; pci_set_master(ha->pdev); - pci_try_set_mwi(ha->pdev); + pci_set_mwi(ha->pdev); pci_read_config_word(ha->pdev, PCI_COMMAND, &w); w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); @@ -2388,7 +2388,7 @@ qla2300_pci_config(scsi_qla_host_t *vha) struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; pci_set_master(ha->pdev); - pci_try_set_mwi(ha->pdev); + pci_set_mwi(ha->pdev); pci_read_config_word(ha->pdev, PCI_COMMAND, &w); w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); @@ -2469,7 +2469,7 @@ qla24xx_pci_config(scsi_qla_host_t *vha) struct device_reg_24xx __iomem *reg = &ha->iobase->isp24; pci_set_master(ha->pdev); - pci_try_set_mwi(ha->pdev); + pci_set_mwi(ha->pdev); pci_read_config_word(ha->pdev, PCI_COMMAND, &w); w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); @@ -2511,7 +2511,7 @@ qla25xx_pci_config(scsi_qla_host_t *vha) struct qla_hw_data *ha = vha->hw; pci_set_master(ha->pdev); - pci_try_set_mwi(ha->pdev); + pci_set_mwi(ha->pdev); pci_read_config_word(ha->pdev, PCI_COMMAND, &w); w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); diff --git a/drivers/scsi/qla2xxx/qla_mr.c b/drivers/scsi/qla2xxx/qla_mr.c index ca7306685..e9763d8e3 100644 --- a/drivers/scsi/qla2xxx/qla_mr.c +++ b/drivers/scsi/qla2xxx/qla_mr.c @@ -499,7 +499,7 @@ qlafx00_pci_config(scsi_qla_host_t *vha) struct qla_hw_data *ha = vha->hw; pci_set_master(ha->pdev); - pci_try_set_mwi(ha->pdev); + pci_set_mwi(ha->pdev); pci_read_config_word(ha->pdev, PCI_COMMAND, &w); w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c index 4dee8a9e0..8acc1e5c9 100644 --- a/drivers/tty/serial/8250/8250_lpss.c +++ b/drivers/tty/serial/8250/8250_lpss.c @@ -193,7 +193,7 @@ static void qrk_serial_setup_dma(struct lpss8250 *lpss, struct uart_port *port) if (ret) return; - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* Special DMA address for UART */ dma->rx_dma_addr = 0xfffff000; diff --git a/drivers/usb/chipidea/ci_hdrc_pci.c b/drivers/usb/chipidea/ci_hdrc_pci.c index d63479e1a..d412fa910 100644 --- a/drivers/usb/chipidea/ci_hdrc_pci.c +++ b/drivers/usb/chipidea/ci_hdrc_pci.c @@ -78,7 +78,7 @@ static int ci_hdrc_pci_probe(struct pci_dev *pdev, } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* register a nop PHY */ ci->phy = usb_phy_generic_register(); diff --git a/drivers/usb/gadget/udc/amd5536udc_pci.c b/drivers/usb/gadget/udc/amd5536udc_pci.c index 8d387e0e4..9630ce8d3 100644 --- a/drivers/usb/gadget/udc/amd5536udc_pci.c +++ b/drivers/usb/gadget/udc/amd5536udc_pci.c @@ -151,7 +151,7 @@ static int udc_pci_probe( dev->chiprev = pdev->revision; pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* init dma pools */ if (use_dma) { diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c index fc9f99fe7..e15520698 100644 --- a/drivers/usb/gadget/udc/net2280.c +++ b/drivers/usb/gadget/udc/net2280.c @@ -3761,7 +3761,7 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id) &dev->pci->pcimstctl); /* erratum 0115 shouldn't appear: Linux inits PCI_LATENCY_TIMER */ pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* ... also flushes any posted pci writes */ dev->chiprev = get_idx_reg(dev->regs, REG_CHIPREV) & 0xffff; diff --git a/drivers/usb/gadget/udc/pch_udc.c b/drivers/usb/gadget/udc/pch_udc.c index a3c1fc924..4a0484a0c 100644 --- a/drivers/usb/gadget/udc/pch_udc.c +++ b/drivers/usb/gadget/udc/pch_udc.c @@ -3100,7 +3100,7 @@ static int pch_udc_probe(struct pci_dev *pdev, } pci_set_master(pdev); - pci_try_set_mwi(pdev); + pci_set_mwi(pdev); /* device struct setup */ spin_lock_init(&dev->lock); diff --git a/include/linux/pci.h b/include/linux/pci.h index de75f6a4d..c590f616d 100644 --- a/include/linux/pci.h +++ b/include/linux/pci.h @@ -1191,9 +1191,8 @@ void pci_clear_master(struct pci_dev *dev); int pci_set_pcie_reset_state(struct pci_dev *dev, enum pcie_reset_state state); int pci_set_cacheline_size(struct pci_dev *dev); -int __must_check pci_set_mwi(struct pci_dev *dev); -int __must_check pcim_set_mwi(struct pci_dev *dev); -int pci_try_set_mwi(struct pci_dev *dev); +int pci_set_mwi(struct pci_dev *dev); +int pcim_set_mwi(struct pci_dev *dev); void pci_clear_mwi(struct pci_dev *dev); void pci_intx(struct pci_dev *dev, int enable); bool pci_check_and_mask_intx(struct pci_dev *dev);
pci_set_mwi() and pci_try_set_mwi() do exactly the same, just that the former one is declared as __must_check. However also some callers of pci_set_mwi() have a comment that it's an optional feature. I don't think there's much sense in this separation and the use of __must_check. Therefore remove pci_try_set_mwi() and remove the __must_check attribute from pci_set_mwi(). I don't expect either function to be used in new code anyway. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> --- patch applies on top of pci/misc for v5.11 --- Documentation/PCI/pci.rst | 5 +---- drivers/ata/pata_cs5530.c | 2 +- drivers/ata/sata_mv.c | 2 +- drivers/dma/dw/pci.c | 2 +- drivers/dma/hsu/pci.c | 2 +- drivers/ide/cs5530.c | 2 +- drivers/mfd/intel-lpss-pci.c | 2 +- drivers/net/ethernet/adaptec/starfire.c | 2 +- drivers/net/ethernet/alacritech/slicoss.c | 2 +- drivers/net/ethernet/dec/tulip/tulip_core.c | 5 +---- drivers/net/ethernet/sun/cassini.c | 4 ++-- drivers/net/wireless/intersil/p54/p54pci.c | 2 +- .../intersil/prism54/islpci_hotplug.c | 3 +-- .../wireless/realtek/rtl818x/rtl8180/dev.c | 2 +- drivers/pci/pci.c | 19 ------------------- drivers/scsi/3w-9xxx.c | 4 ++-- drivers/scsi/3w-sas.c | 4 ++-- drivers/scsi/csiostor/csio_init.c | 2 +- drivers/scsi/lpfc/lpfc_init.c | 2 +- drivers/scsi/qla2xxx/qla_init.c | 8 ++++---- drivers/scsi/qla2xxx/qla_mr.c | 2 +- drivers/tty/serial/8250/8250_lpss.c | 2 +- drivers/usb/chipidea/ci_hdrc_pci.c | 2 +- drivers/usb/gadget/udc/amd5536udc_pci.c | 2 +- drivers/usb/gadget/udc/net2280.c | 2 +- drivers/usb/gadget/udc/pch_udc.c | 2 +- include/linux/pci.h | 5 ++--- 27 files changed, 33 insertions(+), 60 deletions(-)