new file mode 100644
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/mchp,i2s-mcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip I2S Multi-Channel Controller
+
+maintainers:
+ - Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
+
+description:
+ The I2SMCC complies with the Inter-IC Sound (I2S) bus specification and
+ supports a Time Division Multiplexed (TDM) interface with external
+ multi-channel audio codecs. It consists of a receiver, a transmitter and a
+ common clock generator that can be enabled separately to provide Adapter,
+ Client or Controller modes with receiver and/or transmitter active.
+ On later I2SMCC versions (starting with Microchip's SAMA7G5) I2S
+ multi-channel is supported by using multiple data pins, output and
+ input, without TDM.
+
+properties:
+ "#sound-dai-cells":
+ const: 0
+
+ compatible:
+ enum:
+ - microchip,sam9x60-i2smcc
+ - microchip,sama7g5-i2smcc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Peripheral Bus Clock
+ - description: Generic Clock (Optional). Should be set mostly when Master
+ Mode is required.
+ minItems: 1
+
+ clock-names:
+ items:
+ - const: pclk
+ - const: gclk
+ minItems: 1
+
+ dmas:
+ items:
+ - description: TX DMA Channel
+ - description: RX DMA Channel
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+ microchip,tdm-data-pair:
+ description:
+ Represents the DIN/DOUT pair pins that are used to receive/send
+ TDM data. It is optional and it is only needed if the controller
+ uses the TDM mode.
+ $ref: /schemas/types.yaml#/definitions/uint8
+ enum: [0, 1, 2, 3]
+ default: 0
+
+if:
+ properties:
+ compatible:
+ const: microchip,sam9x60-i2smcc
+then:
+ properties:
+ microchip,tdm-data-pair: false
+
+required:
+ - "#sound-dai-cells"
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - dmas
+ - dma-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/dma/at91.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ i2s@f001c000 {
+ #sound-dai-cells = <0>;
+ compatible = "microchip,sam9x60-i2smcc";
+ reg = <0xf001c000 0x100>;
+ interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(36))>,
+ <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(37))>;
+ dma-names = "tx", "rx";
+ clocks = <&i2s_clk>, <&i2s_gclk>;
+ clock-names = "pclk", "gclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2s_default>;
+ };
deleted file mode 100644
@@ -1,49 +0,0 @@
-* Microchip I2S Multi-Channel Controller
-
-Required properties:
-- compatible: Should be "microchip,sam9x60-i2smcc" or
- "microchip,sama7g5-i2smcc".
-- reg: Should be the physical base address of the controller and the
- length of memory mapped region.
-- interrupts: Should contain the interrupt for the controller.
-- dmas: Should be one per channel name listed in the dma-names property,
- as described in atmel-dma.txt and dma.txt files.
-- dma-names: Identifier string for each DMA request line in the dmas property.
- Two dmas have to be defined, "tx" and "rx".
-- clocks: Must contain an entry for each entry in clock-names.
- Please refer to clock-bindings.txt.
-- clock-names: Should be one of each entry matching the clocks phandles list:
- - "pclk" (peripheral clock) Required.
- - "gclk" (generated clock) Optional (1).
-
-Optional properties:
-- pinctrl-0: Should specify pin control groups used for this controller.
-- princtrl-names: Should contain only one value - "default".
-- microchip,tdm-data-pair: 8 bit value that represents the DIN/DOUT pair pins
- which are used to receive/send TDM data. It is optional
- and it is only needed if the controller uses the TDM
- mode. Not available for "microchip,sam9x60-i2smcc"
- compatible. If it's not present, the default value is 0,
- so the DIN/DOUT 0 pins are used.
-
-(1) : Only the peripheral clock is required. The generated clock is optional
- and should be set mostly when Master Mode is required.
-
-Example:
-
- i2s@f001c000 {
- compatible = "microchip,sam9x60-i2smcc";
- reg = <0xf001c000 0x100>;
- interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
- dmas = <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(36))>,
- <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(37))>;
- dma-names = "tx", "rx";
- clocks = <&i2s_clk>, <&i2s_gclk>;
- clock-names = "pclk", "gclk";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2s_default>;
- };
This patch converts the Microchip I2SMCC bindings to DT schema format using json-schema. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> --- Changes in v2: - moved from the beginning to the end of the patch series; - includes the changes (to yaml) from the rest of the patches that update the DT binding; .../bindings/sound/mchp,i2s-mcc.yaml | 108 ++++++++++++++++++ .../bindings/sound/mchp-i2s-mcc.txt | 49 -------- 2 files changed, 108 insertions(+), 49 deletions(-) create mode 100644 Documentation/devicetree/bindings/sound/mchp,i2s-mcc.yaml delete mode 100644 Documentation/devicetree/bindings/sound/mchp-i2s-mcc.txt