diff mbox series

[RFC,net-next,2/3] net: hsr: add DSA offloading support

Message ID 20210122155948.5573-3-george.mccollister@gmail.com
State New
Headers show
Series None | expand

Commit Message

George McCollister Jan. 22, 2021, 3:59 p.m. UTC
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding on DSA switches.

Use a new netdev_priv_flag IFF_HSR to indicate that a device is an HSR
device so DSA can tell them apart from other devices in
dsa_slave_changeupper.

Add DSA_NOTIFIER_HSR_JOIN and DSA_NOTIFIER_HSR_LEAVE which trigger calls
to .port_hsr_join and .port_hsr_leave in the DSA driver for the switch.

The DSA switch driver should then set netdev feature flags for the
HSR/PRP operation that it offloads.
    NETIF_F_HW_HSR_TAG_INS
    NETIF_F_HW_HSR_TAG_RM
    NETIF_F_HW_HSR_FWD
    NETIF_F_HW_HSR_DUP

For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.

Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also preforms auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).

Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.

Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.

Signed-off-by: George McCollister <george.mccollister@gmail.com>
---
 Documentation/networking/netdev-features.rst | 20 ++++++++++++++++
 include/linux/if_hsr.h                       | 22 ++++++++++++++++++
 include/linux/netdev_features.h              |  9 ++++++++
 include/linux/netdevice.h                    | 13 +++++++++++
 include/net/dsa.h                            | 13 +++++++++++
 net/dsa/dsa_priv.h                           | 11 +++++++++
 net/dsa/port.c                               | 34 ++++++++++++++++++++++++++++
 net/dsa/slave.c                              | 13 +++++++++++
 net/dsa/switch.c                             | 24 ++++++++++++++++++++
 net/ethtool/common.c                         |  4 ++++
 net/hsr/hsr_device.c                         | 12 +++-------
 net/hsr/hsr_forward.c                        | 27 +++++++++++++++++++---
 net/hsr/hsr_forward.h                        |  1 +
 net/hsr/hsr_main.c                           | 14 ++++++++++++
 net/hsr/hsr_main.h                           |  8 +------
 net/hsr/hsr_slave.c                          | 13 +++++++----
 16 files changed, 215 insertions(+), 23 deletions(-)
 create mode 100644 include/linux/if_hsr.h

Comments

Florian Fainelli Jan. 22, 2021, 5:56 p.m. UTC | #1
On 1/22/2021 7:59 AM, George McCollister wrote:
> Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
> tag removal, duplicate generation and forwarding on DSA switches.
> 
> Use a new netdev_priv_flag IFF_HSR to indicate that a device is an HSR
> device so DSA can tell them apart from other devices in
> dsa_slave_changeupper.
> 
> Add DSA_NOTIFIER_HSR_JOIN and DSA_NOTIFIER_HSR_LEAVE which trigger calls
> to .port_hsr_join and .port_hsr_leave in the DSA driver for the switch.
> 
> The DSA switch driver should then set netdev feature flags for the
> HSR/PRP operation that it offloads.
>     NETIF_F_HW_HSR_TAG_INS
>     NETIF_F_HW_HSR_TAG_RM
>     NETIF_F_HW_HSR_FWD
>     NETIF_F_HW_HSR_DUP
> 
> For HSR, insertion involves the switch adding a 6 byte HSR header after
> the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
> 
> Tag removal involves automatically stripping the HSR/PRP header/trailer
> in the switch. This is possible when the switch also preforms auto
> deduplication using the HSR/PRP header/trailer (making it no longer
> required).
> 
> Forwarding involves automatically forwarding between redundant ports in
> an HSR. This is crucial because delay is accumulated as a frame passes
> through each node in the ring.
> 
> Duplication involves the switch automatically sending a single frame
> from the CPU port to both redundant ports. This is required because the
> inserted HSR/PRP header/trailer must contain the same sequence number
> on the frames sent out both redundant ports.
> 
> Signed-off-by: George McCollister <george.mccollister@gmail.com>

This is just a high level overview for now, but I would split this into two:

- a patch that adds HSR offload to the existing HSR stack and introduces
the new netdev_features_t bits to support HSR offload, more on that below

- a patch that does the plumbing between HSR and within the DSA framework

> ---
>  Documentation/networking/netdev-features.rst | 20 ++++++++++++++++
>  include/linux/if_hsr.h                       | 22 ++++++++++++++++++
>  include/linux/netdev_features.h              |  9 ++++++++
>  include/linux/netdevice.h                    | 13 +++++++++++
>  include/net/dsa.h                            | 13 +++++++++++
>  net/dsa/dsa_priv.h                           | 11 +++++++++
>  net/dsa/port.c                               | 34 ++++++++++++++++++++++++++++
>  net/dsa/slave.c                              | 13 +++++++++++
>  net/dsa/switch.c                             | 24 ++++++++++++++++++++
>  net/ethtool/common.c                         |  4 ++++
>  net/hsr/hsr_device.c                         | 12 +++-------
>  net/hsr/hsr_forward.c                        | 27 +++++++++++++++++++---
>  net/hsr/hsr_forward.h                        |  1 +
>  net/hsr/hsr_main.c                           | 14 ++++++++++++
>  net/hsr/hsr_main.h                           |  8 +------
>  net/hsr/hsr_slave.c                          | 13 +++++++----
>  16 files changed, 215 insertions(+), 23 deletions(-)
>  create mode 100644 include/linux/if_hsr.h
> 
> diff --git a/Documentation/networking/netdev-features.rst b/Documentation/networking/netdev-features.rst
> index a2d7d7160e39..4eab45405031 100644
> --- a/Documentation/networking/netdev-features.rst
> +++ b/Documentation/networking/netdev-features.rst
> @@ -182,3 +182,23 @@ stricter than Hardware LRO.  A packet stream merged by Hardware GRO must
>  be re-segmentable by GSO or TSO back to the exact original packet stream.
>  Hardware GRO is dependent on RXCSUM since every packet successfully merged
>  by hardware must also have the checksum verified by hardware.
> +
> +* hsr-tag-ins-offload
> +
> +This should be set for devices which insert an HSR (highspeed ring) tag
> +automatically when in HSR mode.
> +
> +* hsr-tag-rm-offload
> +
> +This should be set for devices which remove HSR (highspeed ring) tags
> +automatically when in HSR mode.
> +
> +* hsr-fwd-offload
> +
> +This should be set for devices which forward HSR (highspeed ring) frames from
> +one port to another in hardware.
> +
> +* hsr-dup-offload
> +
> +This should be set for devices which duplicate outgoing HSR (highspeed ring)
> +frames in hardware.

Do you think we can start with a hsr-hw-offload feature and create new
bits to described how challenged a device may be with HSR offload? Is it
 reasonable assumption that functional hardware should be able to
offload all of these functions or none of them?

It may be a good idea to know what the platform that Murali is working
on or has worked on is capable of doing, too.

[snip]

>  
> +static inline bool netif_is_hsr_master(const struct net_device *dev)
> +{
> +	return dev->flags & IFF_MASTER && dev->priv_flags & IFF_HSR;
> +}
> +
> +static inline bool netif_is_hsr_slave(const struct net_device *dev)
> +{
> +	return dev->flags & IFF_SLAVE && dev->priv_flags & IFF_HSR;
> +}

I believe the kernel community is now trying to eliminate the use of the
terms master and slave, can you replace these with some HSR specific
naming maybe?
Nishanth Menon Jan. 22, 2021, 6:48 p.m. UTC | #2
On 10:00-20210122, Florian Fainelli wrote:
[...]

> >> +
> >> +This should be set for devices which duplicate outgoing HSR (highspeed ring)
> >> +frames in hardware.
> > 
> > Do you think we can start with a hsr-hw-offload feature and create new
> > bits to described how challenged a device may be with HSR offload? Is it
> >  reasonable assumption that functional hardware should be able to
> > offload all of these functions or none of them?
> > 
> > It may be a good idea to know what the platform that Murali is working
> > on or has worked on is capable of doing, too.
> 
> Murali's email address is bouncing, adding Grygorii, Kishon and
> Nishanth, they may know.

Gee, thanks for looping us in.. Yup, unfortunately, Murali is no longer
with TI. I have bounced the email over to right folks, whom I hope will
be able to help add more color..
Vladimir Oltean Jan. 24, 2021, 8:43 a.m. UTC | #3
Hi George,

On Fri, Jan 22, 2021 at 12:48:11PM -0600, Nishanth Menon wrote:
> On 10:00-20210122, Florian Fainelli wrote:

> [...]

>

> > >> +

> > >> +This should be set for devices which duplicate outgoing HSR (highspeed ring)

> > >> +frames in hardware.

> > >

> > > Do you think we can start with a hsr-hw-offload feature and create new

> > > bits to described how challenged a device may be with HSR offload? Is it

> > >  reasonable assumption that functional hardware should be able to

> > > offload all of these functions or none of them?

> > >

> > > It may be a good idea to know what the platform that Murali is working

> > > on or has worked on is capable of doing, too.

> >

> > Murali's email address is bouncing, adding Grygorii, Kishon and

> > Nishanth, they may know.

>

> Gee, thanks for looping us in.. Yup, unfortunately, Murali is no longer

> with TI. I have bounced the email over to right folks, whom I hope will

> be able to help add more color..


I would like to give HSR a spin to get a better idea of what you're doing, but
it's kinda hard when this happens out of the box, with none of your changes
already:

[ 1385.000453] hsr0: hw csum failure
[ 1385.004105] skb len=333 headroom=78 headlen=333 tailroom=293
[ 1385.004105] mac=(64,14) net=(78,20) trans=98
[ 1385.004105] shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
[ 1385.004105] csum(0x14a00 ip_summed=2 complete_sw=0 valid=0 level=0)
[ 1385.004105] hash(0x0 sw=0 l4=0) proto=0x0800 pkttype=1 iif=16
[ 1385.032520] dev name=hsr0 feat=0x0x0000000000007400
[ 1385.037496] skb headroom: 00000000: 44 00 00 02 18 00 00 06 ef 00 00 00 b4 da ff ff
[ 1385.045257] skb headroom: 00000010: ff ff ff ff 00 04 9f 05 de 0a 81 00 08 00 08 00
[ 1385.053013] skb headroom: 00000020: 45 00 01 4d e1 e0 00 00 40 11 97 c0 00 00 00 00
[ 1385.060767] skb headroom: 00000030: ff ff ff ff 00 44 00 43 01 39 f3 8a 01 01 06 00
[ 1385.068521] skb headroom: 00000040: ff ff ff ff ff ff 00 04 9f 05 f4 ab 08 00
[ 1385.075753] skb linear:   00000000: 45 00 01 4d f4 b2 00 00 40 11 84 ee 00 00 00 00
[ 1385.083508] skb linear:   00000010: ff ff ff ff 00 44 00 43 01 39 e7 0e 01 01 06 00
[ 1385.091262] skb linear:   00000020: 90 5c 56 3c 00 7c 00 00 00 00 00 00 00 00 00 00
[ 1385.099116] skb linear:   00000030: 00 00 00 00 00 00 00 00 00 04 9f 05 f4 ab 00 00
[ 1385.106874] skb linear:   00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.114628] skb linear:   00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.122380] skb linear:   00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.130132] skb linear:   00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.137883] skb linear:   00000080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.145635] skb linear:   00000090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.153386] skb linear:   000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.161139] skb linear:   000000b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.168890] skb linear:   000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.176641] skb linear:   000000d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.184392] skb linear:   000000e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.192144] skb linear:   000000f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.199896] skb linear:   00000100: 00 00 00 00 00 00 00 00 63 82 53 63 35 01 01 3d
[ 1385.207730] skb linear:   00000110: 13 ff 9f 05 f4 ab 00 01 00 01 26 da 82 ac 00 04
[ 1385.215566] skb linear:   00000120: 9f 05 de 0a 50 00 74 01 01 39 02 05 ba 0c 0a 4c
[ 1385.223323] skb linear:   00000130: 53 31 30 32 38 41 52 44 42 91 01 01 37 0e 01 79
[ 1385.231075] skb linear:   00000140: 21 03 06 0c 0f 1a 1c 33 36 3a 3b 77 ff
[ 1385.238042] skb tailroom: 00000000: 32 39 30 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.245795] skb tailroom: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.253547] skb tailroom: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.261298] skb tailroom: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.269050] skb tailroom: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.276801] skb tailroom: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.284553] skb tailroom: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.292304] skb tailroom: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.300110] skb tailroom: 00000080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.307864] skb tailroom: 00000090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.315615] skb tailroom: 000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.323367] skb tailroom: 000000b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.331119] skb tailroom: 000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.338871] skb tailroom: 000000d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.346622] skb tailroom: 000000e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.354373] skb tailroom: 000000f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.362124] skb tailroom: 00000100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.369875] skb tailroom: 00000110: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1385.377626] skb tailroom: 00000120: 00 00 00 00 00
[ 1385.382504] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.11.0-rc4+ #410
[ 1385.389117] Hardware name: LS1028A RDB Board (DT)
[ 1385.393885] Call trace:
[ 1385.396380]  dump_backtrace+0x0/0x1f0
[ 1385.400130]  show_stack+0x24/0x80
[ 1385.403516]  dump_stack+0xf8/0x168
[ 1385.406990]  netdev_rx_csum_fault.part.0+0x54/0x64
[ 1385.411861]  netdev_rx_csum_fault+0x48/0x50
[ 1385.416119]  __skb_checksum_complete+0x110/0x120
[ 1385.420811]  nf_ip_checksum+0x88/0x160
[ 1385.424636]  nf_checksum+0x58/0x70
[ 1385.428110]  nf_conntrack_udp_packet+0x194/0x2a0
[ 1385.432807]  nf_conntrack_in+0x148/0x7d0
[ 1385.436800]  ipv4_conntrack_in+0x24/0x30
[ 1385.440797]  nf_hook_slow+0x58/0x100
[ 1385.444443]  ip_rcv+0x13c/0x210
[ 1385.447654]  __netif_receive_skb_one_core+0x60/0x90
[ 1385.452603]  __netif_receive_skb+0x20/0x70
[ 1385.456764]  process_backlog+0x138/0x2e4
[ 1385.460753]  net_rx_action+0x12c/0x424
[ 1385.464566]  __do_softirq+0x1f4/0x630
[ 1385.468291]  __irq_exit_rcu+0x194/0x1c0
[ 1385.472199]  irq_exit+0x1c/0x4c
[ 1385.475407]  __handle_domain_irq+0x8c/0xec
[ 1385.479574]  gic_handle_irq+0xcc/0x14c
[ 1385.483386]  el1_irq+0xb4/0x180
[ 1385.486589]  cpuidle_enter_state+0xdc/0x31c
[ 1385.490844]  cpuidle_enter+0x44/0x5c
[ 1385.494486]  do_idle+0x240/0x2d0
[ 1385.497775]  cpu_startup_entry+0x30/0x8c
[ 1385.501762]  rest_init+0x1b8/0x28c
[ 1385.505226]  arch_call_rest_init+0x1c/0x28
[ 1385.509397]  start_kernel+0x580/0x5b8
Vladimir Oltean Jan. 24, 2021, 5:29 p.m. UTC | #4
On Fri, Jan 22, 2021 at 09:59:47AM -0600, George McCollister wrote:
> diff --git a/net/dsa/slave.c b/net/dsa/slave.c

> index f2fb433f3828..fc7e3ff11c5c 100644

> --- a/net/dsa/slave.c

> +++ b/net/dsa/slave.c

> @@ -1924,6 +1924,19 @@ static int dsa_slave_changeupper(struct net_device *dev,

>  			dsa_port_lag_leave(dp, info->upper_dev);

>  			err = NOTIFY_OK;

>  		}

> +	} else if (netif_is_hsr_master(info->upper_dev)) {

> +		if (info->linking) {

> +			err = dsa_port_hsr_join(dp, info->upper_dev);

> +			if (err == -EOPNOTSUPP) {

> +				NL_SET_ERR_MSG_MOD(info->info.extack,

> +						   "Offloading not supported");

> +				err = 0;

> +			}

> +			err = notifier_from_errno(err);

> +		} else {

> +			dsa_port_hsr_leave(dp, info->upper_dev);

> +			err = NOTIFY_OK;

> +		}

>  	}


How is the RedBox use case handled with the Linux hsr driver (i.e. a
HSR-unaware SAN endpoint attached to a HSR ring)? I would expect
something like this:

                   +---------+
                   |         |
                   |   SAN   |
                   |         |
                   +---------+
                        |
                        |
                        |
 +-----------------+---------+------------------+
 |                 |         |                  |
 |  Your           |   swp0  |                  |
 |  board          |         |                  |
 |                 +---------+                  |
 |                    |   ^                     |
 |                    |   |                     |
 |                    |   | br0                 |
 |                    |   |                     |
 |                    v   |                     |
 |       +-----------------------------+        |
 |       |                             |        |
 |       |             hsr0            |        |
 |       |                             |        |
 |       +---------+---------+---------+        |
 |       |         |         |         |        |
 |       |   swp1  |  DAN-H  |  swp2   |        |
 |       |         |         |         |        |
 +-------+---------+---------+---------+--------+
            |   ^               |   ^
    to/from |   |               |   | to/from
     ring   |   |               |   |  ring
            v   |               v   |

Therefore, aren't you interested in offloading this setup as well?
I.e. the case where the hsr0 interface joins a bridge that also
contains other DSA switch ports. This would be similar to the LAG
offload recently added by Tobias.
George McCollister Jan. 25, 2021, 1:56 p.m. UTC | #5
On Sun, Jan 24, 2021 at 2:43 AM Vladimir Oltean <olteanv@gmail.com> wrote:
>

[snip]
>

> I would like to give HSR a spin to get a better idea of what you're doing, but

> it's kinda hard when this happens out of the box, with none of your changes

> already:

>

> [ 1385.000453] hsr0: hw csum failure

> [ 1385.004105] skb len=333 headroom=78 headlen=333 tailroom=293

> [ 1385.004105] mac=(64,14) net=(78,20) trans=98

> [ 1385.004105] shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))

> [ 1385.004105] csum(0x14a00 ip_summed=2 complete_sw=0 valid=0 level=0)

> [ 1385.004105] hash(0x0 sw=0 l4=0) proto=0x0800 pkttype=1 iif=16

> [ 1385.032520] dev name=hsr0 feat=0x0x0000000000007400

> [ 1385.037496] skb headroom: 00000000: 44 00 00 02 18 00 00 06 ef 00 00 00 b4 da ff ff

> [ 1385.045257] skb headroom: 00000010: ff ff ff ff 00 04 9f 05 de 0a 81 00 08 00 08 00

> [ 1385.053013] skb headroom: 00000020: 45 00 01 4d e1 e0 00 00 40 11 97 c0 00 00 00 00

> [ 1385.060767] skb headroom: 00000030: ff ff ff ff 00 44 00 43 01 39 f3 8a 01 01 06 00

> [ 1385.068521] skb headroom: 00000040: ff ff ff ff ff ff 00 04 9f 05 f4 ab 08 00

> [ 1385.075753] skb linear:   00000000: 45 00 01 4d f4 b2 00 00 40 11 84 ee 00 00 00 00

> [ 1385.083508] skb linear:   00000010: ff ff ff ff 00 44 00 43 01 39 e7 0e 01 01 06 00

> [ 1385.091262] skb linear:   00000020: 90 5c 56 3c 00 7c 00 00 00 00 00 00 00 00 00 00

> [ 1385.099116] skb linear:   00000030: 00 00 00 00 00 00 00 00 00 04 9f 05 f4 ab 00 00

> [ 1385.106874] skb linear:   00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.114628] skb linear:   00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.122380] skb linear:   00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.130132] skb linear:   00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.137883] skb linear:   00000080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.145635] skb linear:   00000090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.153386] skb linear:   000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.161139] skb linear:   000000b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.168890] skb linear:   000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.176641] skb linear:   000000d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.184392] skb linear:   000000e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.192144] skb linear:   000000f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.199896] skb linear:   00000100: 00 00 00 00 00 00 00 00 63 82 53 63 35 01 01 3d

> [ 1385.207730] skb linear:   00000110: 13 ff 9f 05 f4 ab 00 01 00 01 26 da 82 ac 00 04

> [ 1385.215566] skb linear:   00000120: 9f 05 de 0a 50 00 74 01 01 39 02 05 ba 0c 0a 4c

> [ 1385.223323] skb linear:   00000130: 53 31 30 32 38 41 52 44 42 91 01 01 37 0e 01 79

> [ 1385.231075] skb linear:   00000140: 21 03 06 0c 0f 1a 1c 33 36 3a 3b 77 ff

> [ 1385.238042] skb tailroom: 00000000: 32 39 30 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.245795] skb tailroom: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.253547] skb tailroom: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.261298] skb tailroom: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.269050] skb tailroom: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.276801] skb tailroom: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.284553] skb tailroom: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.292304] skb tailroom: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.300110] skb tailroom: 00000080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.307864] skb tailroom: 00000090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.315615] skb tailroom: 000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.323367] skb tailroom: 000000b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.331119] skb tailroom: 000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.338871] skb tailroom: 000000d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.346622] skb tailroom: 000000e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.354373] skb tailroom: 000000f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.362124] skb tailroom: 00000100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.369875] skb tailroom: 00000110: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

> [ 1385.377626] skb tailroom: 00000120: 00 00 00 00 00

> [ 1385.382504] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.11.0-rc4+ #410

> [ 1385.389117] Hardware name: LS1028A RDB Board (DT)

> [ 1385.393885] Call trace:

> [ 1385.396380]  dump_backtrace+0x0/0x1f0

> [ 1385.400130]  show_stack+0x24/0x80

> [ 1385.403516]  dump_stack+0xf8/0x168

> [ 1385.406990]  netdev_rx_csum_fault.part.0+0x54/0x64

> [ 1385.411861]  netdev_rx_csum_fault+0x48/0x50

> [ 1385.416119]  __skb_checksum_complete+0x110/0x120

> [ 1385.420811]  nf_ip_checksum+0x88/0x160

> [ 1385.424636]  nf_checksum+0x58/0x70

> [ 1385.428110]  nf_conntrack_udp_packet+0x194/0x2a0

> [ 1385.432807]  nf_conntrack_in+0x148/0x7d0

> [ 1385.436800]  ipv4_conntrack_in+0x24/0x30

> [ 1385.440797]  nf_hook_slow+0x58/0x100

> [ 1385.444443]  ip_rcv+0x13c/0x210

> [ 1385.447654]  __netif_receive_skb_one_core+0x60/0x90

> [ 1385.452603]  __netif_receive_skb+0x20/0x70

> [ 1385.456764]  process_backlog+0x138/0x2e4

> [ 1385.460753]  net_rx_action+0x12c/0x424

> [ 1385.464566]  __do_softirq+0x1f4/0x630

> [ 1385.468291]  __irq_exit_rcu+0x194/0x1c0

> [ 1385.472199]  irq_exit+0x1c/0x4c

> [ 1385.475407]  __handle_domain_irq+0x8c/0xec

> [ 1385.479574]  gic_handle_irq+0xcc/0x14c

> [ 1385.483386]  el1_irq+0xb4/0x180

> [ 1385.486589]  cpuidle_enter_state+0xdc/0x31c

> [ 1385.490844]  cpuidle_enter+0x44/0x5c

> [ 1385.494486]  do_idle+0x240/0x2d0

> [ 1385.497775]  cpu_startup_entry+0x30/0x8c

> [ 1385.501762]  rest_init+0x1b8/0x28c

> [ 1385.505226]  arch_call_rest_init+0x1c/0x28

> [ 1385.509397]  start_kernel+0x580/0x5b8


Yikes! I never ran into this on any of the hardware I tested on.

-George
George McCollister Jan. 25, 2021, 2:33 p.m. UTC | #6
On Sun, Jan 24, 2021 at 11:29 AM Vladimir Oltean <olteanv@gmail.com> wrote:
>

> On Fri, Jan 22, 2021 at 09:59:47AM -0600, George McCollister wrote:

> > diff --git a/net/dsa/slave.c b/net/dsa/slave.c

> > index f2fb433f3828..fc7e3ff11c5c 100644

> > --- a/net/dsa/slave.c

> > +++ b/net/dsa/slave.c

> > @@ -1924,6 +1924,19 @@ static int dsa_slave_changeupper(struct net_device *dev,

> >                       dsa_port_lag_leave(dp, info->upper_dev);

> >                       err = NOTIFY_OK;

> >               }

> > +     } else if (netif_is_hsr_master(info->upper_dev)) {

> > +             if (info->linking) {

> > +                     err = dsa_port_hsr_join(dp, info->upper_dev);

> > +                     if (err == -EOPNOTSUPP) {

> > +                             NL_SET_ERR_MSG_MOD(info->info.extack,

> > +                                                "Offloading not supported");

> > +                             err = 0;

> > +                     }

> > +                     err = notifier_from_errno(err);

> > +             } else {

> > +                     dsa_port_hsr_leave(dp, info->upper_dev);

> > +                     err = NOTIFY_OK;

> > +             }

> >       }

>

> How is the RedBox use case handled with the Linux hsr driver (i.e. a

> HSR-unaware SAN endpoint attached to a HSR ring)? I would expect

> something like this:

>

>                    +---------+

>                    |         |

>                    |   SAN   |

>                    |         |

>                    +---------+

>                         |

>                         |

>                         |

>  +-----------------+---------+------------------+

>  |                 |         |                  |

>  |  Your           |   swp0  |                  |

>  |  board          |         |                  |

>  |                 +---------+                  |

>  |                    |   ^                     |

>  |                    |   |                     |

>  |                    |   | br0                 |

>  |                    |   |                     |

>  |                    v   |                     |

>  |       +-----------------------------+        |

>  |       |                             |        |

>  |       |             hsr0            |        |

>  |       |                             |        |

>  |       +---------+---------+---------+        |

>  |       |         |         |         |        |

>  |       |   swp1  |  DAN-H  |  swp2   |        |

>  |       |         |         |         |        |

>  +-------+---------+---------+---------+--------+

>             |   ^               |   ^

>     to/from |   |               |   | to/from

>      ring   |   |               |   |  ring

>             v   |               v   |

>

> Therefore, aren't you interested in offloading this setup as well?

> I.e. the case where the hsr0 interface joins a bridge that also

> contains other DSA switch ports. This would be similar to the LAG

> offload recently added by Tobias.


I'm familiar with this use case but I don't currently need to support
it on products I'm working on and in fact my hardware doesn't support
it because the fourth switch port isn't brought out on the boards.
I've also never tested it in software. I suppose when an hsr is
bridged with a non-HSR switch port it would need to figure out the hsr
redundancy interfaces are on the same switch and configure the
forwarding accordingly. It's also worth noting that on switches which
don't support automatic insertion/deletion of the HSR/PRP tag (like
the ksz9477 I think) this wouldn't be possible.

If someone has hardware that supports this and wants to work with me
to add support for it I'd certainly be open to it. Adding support for
this in the future if demand arises seems like the best plan given
what I have to work with.
diff mbox series

Patch

diff --git a/Documentation/networking/netdev-features.rst b/Documentation/networking/netdev-features.rst
index a2d7d7160e39..4eab45405031 100644
--- a/Documentation/networking/netdev-features.rst
+++ b/Documentation/networking/netdev-features.rst
@@ -182,3 +182,23 @@  stricter than Hardware LRO.  A packet stream merged by Hardware GRO must
 be re-segmentable by GSO or TSO back to the exact original packet stream.
 Hardware GRO is dependent on RXCSUM since every packet successfully merged
 by hardware must also have the checksum verified by hardware.
+
+* hsr-tag-ins-offload
+
+This should be set for devices which insert an HSR (highspeed ring) tag
+automatically when in HSR mode.
+
+* hsr-tag-rm-offload
+
+This should be set for devices which remove HSR (highspeed ring) tags
+automatically when in HSR mode.
+
+* hsr-fwd-offload
+
+This should be set for devices which forward HSR (highspeed ring) frames from
+one port to another in hardware.
+
+* hsr-dup-offload
+
+This should be set for devices which duplicate outgoing HSR (highspeed ring)
+frames in hardware.
diff --git a/include/linux/if_hsr.h b/include/linux/if_hsr.h
new file mode 100644
index 000000000000..eec9079efab0
--- /dev/null
+++ b/include/linux/if_hsr.h
@@ -0,0 +1,22 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_IF_HSR_H_
+#define _LINUX_IF_HSR_H_
+
+/* used to differentiate various protocols */
+enum hsr_version {
+	HSR_V0 = 0,
+	HSR_V1,
+	PRP_V1,
+};
+
+#if IS_ENABLED(CONFIG_HSR)
+extern int hsr_get_version(struct net_device *dev, enum hsr_version *ver);
+#else
+static inline int hsr_get_version(struct net_device *dev,
+				  enum hsr_version *ver)
+{
+	return -EINVAL;
+}
+#endif /* CONFIG_HSR */
+
+#endif /*_LINUX_IF_HSR_H_*/
diff --git a/include/linux/netdev_features.h b/include/linux/netdev_features.h
index 934de56644e7..13b3fa7668bb 100644
--- a/include/linux/netdev_features.h
+++ b/include/linux/netdev_features.h
@@ -85,6 +85,11 @@  enum {
 
 	NETIF_F_HW_MACSEC_BIT,		/* Offload MACsec operations */
 
+	NETIF_F_HW_HSR_TAG_INS_BIT,	/* Offload HSR tag insertion */
+	NETIF_F_HW_HSR_TAG_RM_BIT,	/* Offload HSR tag removal */
+	NETIF_F_HW_HSR_FWD_BIT,		/* Offload HSR forwarding */
+	NETIF_F_HW_HSR_DUP_BIT,		/* Offload HSR duplication */
+
 	/*
 	 * Add your fresh new feature above and remember to update
 	 * netdev_features_strings[] in net/core/ethtool.c and maybe
@@ -157,6 +162,10 @@  enum {
 #define NETIF_F_GRO_FRAGLIST	__NETIF_F(GRO_FRAGLIST)
 #define NETIF_F_GSO_FRAGLIST	__NETIF_F(GSO_FRAGLIST)
 #define NETIF_F_HW_MACSEC	__NETIF_F(HW_MACSEC)
+#define NETIF_F_HW_HSR_TAG_INS	__NETIF_F(HW_HSR_TAG_INS)
+#define NETIF_F_HW_HSR_TAG_RM	__NETIF_F(HW_HSR_TAG_RM)
+#define NETIF_F_HW_HSR_FWD	__NETIF_F(HW_HSR_FWD)
+#define NETIF_F_HW_HSR_DUP	__NETIF_F(HW_HSR_DUP)
 
 /* Finds the next feature with the highest number of the range of start till 0.
  */
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 5b949076ed23..4a1533aff3cf 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -1523,6 +1523,7 @@  struct net_device_ops {
  * @IFF_FAILOVER_SLAVE: device is lower dev of a failover master device
  * @IFF_L3MDEV_RX_HANDLER: only invoke the rx handler of L3 master device
  * @IFF_LIVE_RENAME_OK: rename is allowed while device is up and running
+ * @IFF_HSR: device is an hsr device
  */
 enum netdev_priv_flags {
 	IFF_802_1Q_VLAN			= 1<<0,
@@ -1556,6 +1557,7 @@  enum netdev_priv_flags {
 	IFF_FAILOVER_SLAVE		= 1<<28,
 	IFF_L3MDEV_RX_HANDLER		= 1<<29,
 	IFF_LIVE_RENAME_OK		= 1<<30,
+	IFF_HSR				= 1<<31,
 };
 
 #define IFF_802_1Q_VLAN			IFF_802_1Q_VLAN
@@ -1588,6 +1590,7 @@  enum netdev_priv_flags {
 #define IFF_FAILOVER_SLAVE		IFF_FAILOVER_SLAVE
 #define IFF_L3MDEV_RX_HANDLER		IFF_L3MDEV_RX_HANDLER
 #define IFF_LIVE_RENAME_OK		IFF_LIVE_RENAME_OK
+#define IFF_HSR				IFF_HSR
 
 /**
  *	struct net_device - The DEVICE structure.
@@ -4996,6 +4999,16 @@  static inline bool netif_is_failover_slave(const struct net_device *dev)
 	return dev->priv_flags & IFF_FAILOVER_SLAVE;
 }
 
+static inline bool netif_is_hsr_master(const struct net_device *dev)
+{
+	return dev->flags & IFF_MASTER && dev->priv_flags & IFF_HSR;
+}
+
+static inline bool netif_is_hsr_slave(const struct net_device *dev)
+{
+	return dev->flags & IFF_SLAVE && dev->priv_flags & IFF_HSR;
+}
+
 /* This device needs to keep skb dst for qdisc enqueue or ndo_start_xmit() */
 static inline void netif_keep_dst(struct net_device *dev)
 {
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 2f5435d3d1db..584e2b5c02e0 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -167,6 +167,10 @@  struct dsa_switch_tree {
 	list_for_each_entry((_dp), &(_dst)->ports, list)	\
 		if ((_dp)->lag_dev == (_lag))
 
+#define dsa_hsr_foreach_port(_dp, _ds, _hsr)			\
+	list_for_each_entry((_dp), &(_ds)->dst->ports, list)	\
+		if ((_dp)->ds == (_ds) && (_dp)->hsr_dev == (_hsr))
+
 static inline struct net_device *dsa_lag_dev(struct dsa_switch_tree *dst,
 					     unsigned int id)
 {
@@ -257,6 +261,7 @@  struct dsa_port {
 	struct phylink_config	pl_config;
 	struct net_device	*lag_dev;
 	bool			lag_tx_enabled;
+	struct net_device	*hsr_dev;
 
 	struct list_head list;
 
@@ -753,6 +758,14 @@  struct dsa_switch_ops {
 				 struct netdev_lag_upper_info *info);
 	int	(*port_lag_leave)(struct dsa_switch *ds, int port,
 				  struct net_device *lag);
+
+	/*
+	 * HSR integration
+	 */
+	int	(*port_hsr_join)(struct dsa_switch *ds, int port,
+				 struct net_device *hsr);
+	void	(*port_hsr_leave)(struct dsa_switch *ds, int port,
+				  struct net_device *hsr);
 };
 
 #define DSA_DEVLINK_PARAM_DRIVER(_id, _name, _type, _cmodes)		\
diff --git a/net/dsa/dsa_priv.h b/net/dsa/dsa_priv.h
index 2ce46bb87703..9006f62f69cd 100644
--- a/net/dsa/dsa_priv.h
+++ b/net/dsa/dsa_priv.h
@@ -20,6 +20,8 @@  enum {
 	DSA_NOTIFIER_BRIDGE_LEAVE,
 	DSA_NOTIFIER_FDB_ADD,
 	DSA_NOTIFIER_FDB_DEL,
+	DSA_NOTIFIER_HSR_JOIN,
+	DSA_NOTIFIER_HSR_LEAVE,
 	DSA_NOTIFIER_LAG_CHANGE,
 	DSA_NOTIFIER_LAG_JOIN,
 	DSA_NOTIFIER_LAG_LEAVE,
@@ -94,6 +96,13 @@  struct dsa_switchdev_event_work {
 	u16 vid;
 };
 
+/* DSA_NOTIFIER_HSR_* */
+struct dsa_notifier_hsr_info {
+	struct net_device *hsr;
+	int sw_index;
+	int port;
+};
+
 struct dsa_slave_priv {
 	/* Copy of CPU port xmit for faster access in slave transmit hot path */
 	struct sk_buff *	(*xmit)(struct sk_buff *skb,
@@ -174,6 +183,8 @@  int dsa_port_vlan_del(struct dsa_port *dp,
 		      const struct switchdev_obj_port_vlan *vlan);
 int dsa_port_link_register_of(struct dsa_port *dp);
 void dsa_port_link_unregister_of(struct dsa_port *dp);
+int dsa_port_hsr_join(struct dsa_port *dp, struct net_device *hsr);
+void dsa_port_hsr_leave(struct dsa_port *dp, struct net_device *hsr);
 extern const struct phylink_mac_ops dsa_port_phylink_mac_ops;
 
 static inline bool dsa_port_offloads_netdev(struct dsa_port *dp,
diff --git a/net/dsa/port.c b/net/dsa/port.c
index f5b0f72ee7cd..09738af4d32e 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -870,3 +870,37 @@  int dsa_port_get_phy_sset_count(struct dsa_port *dp)
 	return ret;
 }
 EXPORT_SYMBOL_GPL(dsa_port_get_phy_sset_count);
+
+int dsa_port_hsr_join(struct dsa_port *dp, struct net_device *hsr)
+{
+	struct dsa_notifier_hsr_info info = {
+		.sw_index = dp->ds->index,
+		.port = dp->index,
+		.hsr = hsr,
+	};
+	int err;
+
+	dp->hsr_dev = hsr;
+
+	err = dsa_port_notify(dp, DSA_NOTIFIER_HSR_JOIN, &info);
+	if (err)
+		dp->hsr_dev = NULL;
+
+	return err;
+}
+
+void dsa_port_hsr_leave(struct dsa_port *dp, struct net_device *hsr)
+{
+	struct dsa_notifier_hsr_info info = {
+		.sw_index = dp->ds->index,
+		.port = dp->index,
+		.hsr = hsr,
+	};
+	int err;
+
+	dp->hsr_dev = NULL;
+
+	err = dsa_port_notify(dp, DSA_NOTIFIER_HSR_LEAVE, &info);
+	if (err)
+		pr_err("DSA: failed to notify DSA_NOTIFIER_HSR_LEAVE\n");
+}
diff --git a/net/dsa/slave.c b/net/dsa/slave.c
index f2fb433f3828..fc7e3ff11c5c 100644
--- a/net/dsa/slave.c
+++ b/net/dsa/slave.c
@@ -1924,6 +1924,19 @@  static int dsa_slave_changeupper(struct net_device *dev,
 			dsa_port_lag_leave(dp, info->upper_dev);
 			err = NOTIFY_OK;
 		}
+	} else if (netif_is_hsr_master(info->upper_dev)) {
+		if (info->linking) {
+			err = dsa_port_hsr_join(dp, info->upper_dev);
+			if (err == -EOPNOTSUPP) {
+				NL_SET_ERR_MSG_MOD(info->info.extack,
+						   "Offloading not supported");
+				err = 0;
+			}
+			err = notifier_from_errno(err);
+		} else {
+			dsa_port_hsr_leave(dp, info->upper_dev);
+			err = NOTIFY_OK;
+		}
 	}
 
 	return err;
diff --git a/net/dsa/switch.c b/net/dsa/switch.c
index cc0b25f3adea..c1e5083f2cfc 100644
--- a/net/dsa/switch.c
+++ b/net/dsa/switch.c
@@ -166,6 +166,24 @@  static int dsa_switch_fdb_del(struct dsa_switch *ds,
 	return ds->ops->port_fdb_del(ds, port, info->addr, info->vid);
 }
 
+static int dsa_switch_hsr_join(struct dsa_switch *ds,
+			       struct dsa_notifier_hsr_info *info)
+{
+	if (ds->index == info->sw_index && ds->ops->port_hsr_join)
+		return ds->ops->port_hsr_join(ds, info->port, info->hsr);
+
+	return 0;
+}
+
+static int dsa_switch_hsr_leave(struct dsa_switch *ds,
+				struct dsa_notifier_hsr_info *info)
+{
+	if (ds->index == info->sw_index && ds->ops->port_hsr_leave)
+		ds->ops->port_hsr_leave(ds, info->port, info->hsr);
+
+	return 0;
+}
+
 static int dsa_switch_lag_change(struct dsa_switch *ds,
 				 struct dsa_notifier_lag_info *info)
 {
@@ -319,6 +337,12 @@  static int dsa_switch_event(struct notifier_block *nb,
 	case DSA_NOTIFIER_FDB_DEL:
 		err = dsa_switch_fdb_del(ds, info);
 		break;
+	case DSA_NOTIFIER_HSR_JOIN:
+		err = dsa_switch_hsr_join(ds, info);
+		break;
+	case DSA_NOTIFIER_HSR_LEAVE:
+		err = dsa_switch_hsr_leave(ds, info);
+		break;
 	case DSA_NOTIFIER_LAG_CHANGE:
 		err = dsa_switch_lag_change(ds, info);
 		break;
diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index 24036e3055a1..934e98e495a6 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -68,6 +68,10 @@  const char netdev_features_strings[NETDEV_FEATURE_COUNT][ETH_GSTRING_LEN] = {
 	[NETIF_F_HW_TLS_RX_BIT] =	 "tls-hw-rx-offload",
 	[NETIF_F_GRO_FRAGLIST_BIT] =	 "rx-gro-list",
 	[NETIF_F_HW_MACSEC_BIT] =	 "macsec-hw-offload",
+	[NETIF_F_HW_HSR_TAG_INS_BIT] =	 "hsr-tag-ins-offload",
+	[NETIF_F_HW_HSR_TAG_RM_BIT] =	 "hsr-tag-rm-offload",
+	[NETIF_F_HW_HSR_FWD_BIT] =	 "hsr-fwd-offload",
+	[NETIF_F_HW_HSR_DUP_BIT] =	 "hsr-dup-offload",
 };
 
 const char
diff --git a/net/hsr/hsr_device.c b/net/hsr/hsr_device.c
index 161b8da6a21d..d9b033e9b18c 100644
--- a/net/hsr/hsr_device.c
+++ b/net/hsr/hsr_device.c
@@ -418,6 +418,7 @@  static struct hsr_proto_ops hsr_ops = {
 	.send_sv_frame = send_hsr_supervision_frame,
 	.create_tagged_frame = hsr_create_tagged_frame,
 	.get_untagged_frame = hsr_get_untagged_frame,
+	.drop_frame = hsr_drop_frame,
 	.fill_frame_info = hsr_fill_frame_info,
 	.invalid_dan_ingress_frame = hsr_invalid_dan_ingress_frame,
 };
@@ -521,15 +522,8 @@  int hsr_dev_finalize(struct net_device *hsr_dev, struct net_device *slave[2],
 
 	hsr->prot_version = protocol_version;
 
-	/* FIXME: should I modify the value of these?
-	 *
-	 * - hsr_dev->flags - i.e.
-	 *			IFF_MASTER/SLAVE?
-	 * - hsr_dev->priv_flags - i.e.
-	 *			IFF_EBRIDGE?
-	 *			IFF_TX_SKB_SHARING?
-	 *			IFF_HSR_MASTER/SLAVE?
-	 */
+	hsr_dev->flags |= IFF_MASTER;
+	hsr_dev->priv_flags |= IFF_HSR;
 
 	/* Make sure the 1st call to netif_carrier_on() gets through */
 	netif_carrier_off(hsr_dev);
diff --git a/net/hsr/hsr_forward.c b/net/hsr/hsr_forward.c
index a5566b2245a0..9c79d602c4e0 100644
--- a/net/hsr/hsr_forward.c
+++ b/net/hsr/hsr_forward.c
@@ -247,6 +247,8 @@  struct sk_buff *hsr_create_tagged_frame(struct hsr_frame_info *frame,
 		/* set the lane id properly */
 		hsr_set_path_id(hsr_ethhdr, port);
 		return skb_clone(frame->skb_hsr, GFP_ATOMIC);
+	} else if (port->dev->features & NETIF_F_HW_HSR_TAG_INS) {
+		return skb_clone(frame->skb_std, GFP_ATOMIC);
 	}
 
 	/* Create the new skb with enough headroom to fit the HSR tag */
@@ -341,6 +343,14 @@  bool prp_drop_frame(struct hsr_frame_info *frame, struct hsr_port *port)
 		 port->type ==  HSR_PT_SLAVE_A));
 }
 
+bool hsr_drop_frame(struct hsr_frame_info *frame, struct hsr_port *port)
+{
+	if (port->dev->features & NETIF_F_HW_HSR_FWD)
+		return prp_drop_frame(frame, port);
+
+	return false;
+}
+
 /* Forward the frame through all devices except:
  * - Back through the receiving device
  * - If it's a HSR frame: through a device where it has passed before
@@ -357,6 +367,7 @@  static void hsr_forward_do(struct hsr_frame_info *frame)
 {
 	struct hsr_port *port;
 	struct sk_buff *skb;
+	bool sent = false;
 
 	hsr_for_each_port(frame->port_rcv->hsr, port) {
 		struct hsr_priv *hsr = port->hsr;
@@ -372,6 +383,12 @@  static void hsr_forward_do(struct hsr_frame_info *frame)
 		if (port->type != HSR_PT_MASTER && frame->is_local_exclusive)
 			continue;
 
+		/* If hardware duplicate generation is enabled, only send out
+		 * one port.
+		 */
+		if ((port->dev->features & NETIF_F_HW_HSR_DUP) && sent)
+			continue;
+
 		/* Don't send frame over port where it has been sent before.
 		 * Also fro SAN, this shouldn't be done.
 		 */
@@ -403,10 +420,12 @@  static void hsr_forward_do(struct hsr_frame_info *frame)
 		}
 
 		skb->dev = port->dev;
-		if (port->type == HSR_PT_MASTER)
+		if (port->type == HSR_PT_MASTER) {
 			hsr_deliver_master(skb, port->dev, frame->node_src);
-		else
-			hsr_xmit(skb, port, frame);
+		} else {
+			if (!hsr_xmit(skb, port, frame))
+				sent = true;
+		}
 	}
 }
 
@@ -457,6 +476,7 @@  void hsr_fill_frame_info(__be16 proto, struct sk_buff *skb,
 	struct hsr_port *port = frame->port_rcv;
 
 	if (port->type != HSR_PT_MASTER &&
+	    !(port->dev->features & NETIF_F_HW_HSR_TAG_RM) &&
 	    (proto == htons(ETH_P_PRP) || proto == htons(ETH_P_HSR))) {
 		/* HSR tagged frame :- Data or Supervision */
 		frame->skb_std = NULL;
@@ -478,6 +498,7 @@  void prp_fill_frame_info(__be16 proto, struct sk_buff *skb,
 	struct hsr_port *port = frame->port_rcv;
 
 	if (port->type != HSR_PT_MASTER &&
+	    !(port->dev->features & NETIF_F_HW_HSR_TAG_RM) &&
 	    rct &&
 	    prp_check_lsdu_size(skb, rct, frame->is_supervision)) {
 		frame->skb_hsr = NULL;
diff --git a/net/hsr/hsr_forward.h b/net/hsr/hsr_forward.h
index 618140d484ad..b6acaafa83fc 100644
--- a/net/hsr/hsr_forward.h
+++ b/net/hsr/hsr_forward.h
@@ -23,6 +23,7 @@  struct sk_buff *hsr_get_untagged_frame(struct hsr_frame_info *frame,
 struct sk_buff *prp_get_untagged_frame(struct hsr_frame_info *frame,
 				       struct hsr_port *port);
 bool prp_drop_frame(struct hsr_frame_info *frame, struct hsr_port *port);
+bool hsr_drop_frame(struct hsr_frame_info *frame, struct hsr_port *port);
 void prp_fill_frame_info(__be16 proto, struct sk_buff *skb,
 			 struct hsr_frame_info *frame);
 void hsr_fill_frame_info(__be16 proto, struct sk_buff *skb,
diff --git a/net/hsr/hsr_main.c b/net/hsr/hsr_main.c
index 2fd1976e5b1c..0e7b5b18b5e3 100644
--- a/net/hsr/hsr_main.c
+++ b/net/hsr/hsr_main.c
@@ -131,6 +131,20 @@  struct hsr_port *hsr_port_get_hsr(struct hsr_priv *hsr, enum hsr_port_type pt)
 	return NULL;
 }
 
+int hsr_get_version(struct net_device *dev, enum hsr_version *ver)
+{
+	struct hsr_priv *hsr;
+
+	if (!(dev->priv_flags & IFF_HSR))
+		return -EINVAL;
+
+	hsr = netdev_priv(dev);
+	*ver = hsr->prot_version;
+
+	return 0;
+}
+EXPORT_SYMBOL(hsr_get_version);
+
 static struct notifier_block hsr_nb = {
 	.notifier_call = hsr_netdev_notify,	/* Slave event notifications */
 };
diff --git a/net/hsr/hsr_main.h b/net/hsr/hsr_main.h
index 7dc92ce5a134..7369b2febe0f 100644
--- a/net/hsr/hsr_main.h
+++ b/net/hsr/hsr_main.h
@@ -13,6 +13,7 @@ 
 #include <linux/netdevice.h>
 #include <linux/list.h>
 #include <linux/if_vlan.h>
+#include <linux/if_hsr.h>
 
 /* Time constants as specified in the HSR specification (IEC-62439-3 2010)
  * Table 8.
@@ -171,13 +172,6 @@  struct hsr_port {
 	enum hsr_port_type	type;
 };
 
-/* used by driver internally to differentiate various protocols */
-enum hsr_version {
-	HSR_V0 = 0,
-	HSR_V1,
-	PRP_V1,
-};
-
 struct hsr_frame_info;
 struct hsr_node;
 
diff --git a/net/hsr/hsr_slave.c b/net/hsr/hsr_slave.c
index 36d5fcf09c61..59f8d2b68376 100644
--- a/net/hsr/hsr_slave.c
+++ b/net/hsr/hsr_slave.c
@@ -48,12 +48,14 @@  static rx_handler_result_t hsr_handle_frame(struct sk_buff **pskb)
 		goto finish_consume;
 	}
 
-	/* For HSR, only tagged frames are expected, but for PRP
-	 * there could be non tagged frames as well from Single
-	 * attached nodes (SANs).
+	/* For HSR, only tagged frames are expected (unless the device offloads
+	 * HSR tag removal), but for PRP there could be non tagged frames as
+	 * well from Single attached nodes (SANs).
 	 */
 	protocol = eth_hdr(skb)->h_proto;
-	if (hsr->proto_ops->invalid_dan_ingress_frame &&
+
+	if (!(port->dev->features & NETIF_F_HW_HSR_TAG_RM) &&
+	    hsr->proto_ops->invalid_dan_ingress_frame &&
 	    hsr->proto_ops->invalid_dan_ingress_frame(protocol))
 		goto finish_pass;
 
@@ -137,6 +139,9 @@  static int hsr_portdev_setup(struct hsr_priv *hsr, struct net_device *dev,
 	master = hsr_port_get_hsr(hsr, HSR_PT_MASTER);
 	hsr_dev = master->dev;
 
+	dev->flags |= IFF_SLAVE;
+	dev->priv_flags |= IFF_HSR;
+
 	res = netdev_upper_dev_link(dev, hsr_dev, extack);
 	if (res)
 		goto fail_upper_dev_link;