diff mbox series

[v2,19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

Message ID 20201211011934.6171-20-andre.przywara@arm.com
State Superseded
Headers show
Series None | expand

Commit Message

Andre Przywara Dec. 11, 2020, 1:19 a.m. UTC 
This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
There does not seem to be an extra interrupt controller anymore, also
it lacks the corresponding NMI pin, so no interrupts for the PMIC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++++++++++
 1 file changed, 715 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi

Comments

Maxime Ripard Dec. 14, 2020, 9:58 a.m. UTC | #1 
On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> +	reserved-memory {

> +		#address-cells = <2>;

> +		#size-cells = <2>;

> +		ranges;

> +

> +		/* 512KiB reserved for ARM Trusted Firmware (BL31) */

> +		secmon_reserved: secmon@40000000 {

> +			reg = <0x0 0x40000000 0x0 0x80000>;

> +			no-map;

> +		};

> +	};


This should still be set by the firmware

> +		mmc0: mmc@4020000 {

> +			compatible = "allwinner,sun50i-h616-mmc",

> +				     "allwinner,sun50i-a100-mmc";

> +			reg = <0x04020000 0x1000>;

> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;

> +			clock-names = "ahb", "mmc";

> +			resets = <&ccu RST_BUS_MMC0>;

> +			reset-names = "ahb";

> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;

> +			pinctrl-names = "default";

> +			pinctrl-0 = <&mmc0_pins>;

> +			status = "disabled";

> +			#address-cells = <1>;

> +			#size-cells = <0>;

> +		};


Somewhat related: we shouldn't set the MMC speed flags in the drivers.
This is biting us on the already supported SoCs, so it would be great to
not repeat the same mistake with the new ones

Maxime
Andre Przywara Dec. 14, 2020, 12:53 p.m. UTC | #2 
On Mon, 14 Dec 2020 10:58:31 +0100
Maxime Ripard <maxime@cerno.tech> wrote:

Hi,

> On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:

> > +	reserved-memory {

> > +		#address-cells = <2>;

> > +		#size-cells = <2>;

> > +		ranges;

> > +

> > +		/* 512KiB reserved for ARM Trusted Firmware (BL31)

> > */

> > +		secmon_reserved: secmon@40000000 {

> > +			reg = <0x0 0x40000000 0x0 0x80000>;

> > +			no-map;

> > +		};

> > +	};  

> 

> This should still be set by the firmware

> 

> > +		mmc0: mmc@4020000 {

> > +			compatible = "allwinner,sun50i-h616-mmc",

> > +				     "allwinner,sun50i-a100-mmc";

> > +			reg = <0x04020000 0x1000>;

> > +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu

> > CLK_MMC0>;

> > +			clock-names = "ahb", "mmc";

> > +			resets = <&ccu RST_BUS_MMC0>;

> > +			reset-names = "ahb";

> > +			interrupts = <GIC_SPI 35

> > IRQ_TYPE_LEVEL_HIGH>;

> > +			pinctrl-names = "default";

> > +			pinctrl-0 = <&mmc0_pins>;

> > +			status = "disabled";

> > +			#address-cells = <1>;

> > +			#size-cells = <0>;

> > +		};  

> 

> Somewhat related: we shouldn't set the MMC speed flags in the drivers.

> This is biting us on the already supported SoCs, so it would be great

> to not repeat the same mistake with the new ones


Do you mean to list the "sd-uhs-sdr50" and friends properties here in
the DT?
What is the best practice here in terms putting them in the .dts vs.
the .dtsi? Surely the controller has limits, but bad traces on a board
could impose further restrictions, right? 
Though that's probably rare, so it sounds like a lot of churn to list
them in every board DT. So can we list everything in here (.dtsi), then
delete in those affected boards only?

Cheers,
Andre
Chen-Yu Tsai Dec. 14, 2020, 1:28 p.m. UTC | #3 
On Mon, Dec 14, 2020 at 8:53 PM Andre Przywara <andre.przywara@arm.com> wrote:
>

> On Mon, 14 Dec 2020 10:58:31 +0100

> Maxime Ripard <maxime@cerno.tech> wrote:

>

> Hi,

>

> > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:

> > > +   reserved-memory {

> > > +           #address-cells = <2>;

> > > +           #size-cells = <2>;

> > > +           ranges;

> > > +

> > > +           /* 512KiB reserved for ARM Trusted Firmware (BL31)

> > > */

> > > +           secmon_reserved: secmon@40000000 {

> > > +                   reg = <0x0 0x40000000 0x0 0x80000>;

> > > +                   no-map;

> > > +           };

> > > +   };

> >

> > This should still be set by the firmware

> >

> > > +           mmc0: mmc@4020000 {

> > > +                   compatible = "allwinner,sun50i-h616-mmc",

> > > +                                "allwinner,sun50i-a100-mmc";

> > > +                   reg = <0x04020000 0x1000>;

> > > +                   clocks = <&ccu CLK_BUS_MMC0>, <&ccu

> > > CLK_MMC0>;

> > > +                   clock-names = "ahb", "mmc";

> > > +                   resets = <&ccu RST_BUS_MMC0>;

> > > +                   reset-names = "ahb";

> > > +                   interrupts = <GIC_SPI 35

> > > IRQ_TYPE_LEVEL_HIGH>;

> > > +                   pinctrl-names = "default";

> > > +                   pinctrl-0 = <&mmc0_pins>;

> > > +                   status = "disabled";

> > > +                   #address-cells = <1>;

> > > +                   #size-cells = <0>;

> > > +           };

> >

> > Somewhat related: we shouldn't set the MMC speed flags in the drivers.

> > This is biting us on the already supported SoCs, so it would be great

> > to not repeat the same mistake with the new ones

>

> Do you mean to list the "sd-uhs-sdr50" and friends properties here in

> the DT?

> What is the best practice here in terms putting them in the .dts vs.

> the .dtsi? Surely the controller has limits, but bad traces on a board

> could impose further restrictions, right?

> Though that's probably rare, so it sounds like a lot of churn to list

> them in every board DT. So can we list everything in here (.dtsi), then

> delete in those affected boards only?


The driver will most certainly already have the basic high speed modes
enabled. Or we can list them in the .dtsi file.

For HS-DDR mode, we probably want to list that in the .dtsi file as well,
as that seems to be the one that is failing most of the time.

All the UHS-1 modes would be listed by board, since it requires a way
to cut power to the card and the ability to change I/O voltage levels.

I wonder if Allwinner still keeps the timing information in the driver,
or have they moved that to their vendor device tree files. We might want
to consider moving it as well.

ChenYu
Maxime Ripard Dec. 14, 2020, 2:12 p.m. UTC | #4 
On Mon, Dec 14, 2020 at 12:53:43PM +0000, Andre Przywara wrote:
> On Mon, 14 Dec 2020 10:58:31 +0100

> Maxime Ripard <maxime@cerno.tech> wrote:

> > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:

> > > +	reserved-memory {

> > > +		#address-cells = <2>;

> > > +		#size-cells = <2>;

> > > +		ranges;

> > > +

> > > +		/* 512KiB reserved for ARM Trusted Firmware (BL31)

> > > */

> > > +		secmon_reserved: secmon@40000000 {

> > > +			reg = <0x0 0x40000000 0x0 0x80000>;

> > > +			no-map;

> > > +		};

> > > +	};  

> > 

> > This should still be set by the firmware

> > 

> > > +		mmc0: mmc@4020000 {

> > > +			compatible = "allwinner,sun50i-h616-mmc",

> > > +				     "allwinner,sun50i-a100-mmc";

> > > +			reg = <0x04020000 0x1000>;

> > > +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu

> > > CLK_MMC0>;

> > > +			clock-names = "ahb", "mmc";

> > > +			resets = <&ccu RST_BUS_MMC0>;

> > > +			reset-names = "ahb";

> > > +			interrupts = <GIC_SPI 35

> > > IRQ_TYPE_LEVEL_HIGH>;

> > > +			pinctrl-names = "default";

> > > +			pinctrl-0 = <&mmc0_pins>;

> > > +			status = "disabled";

> > > +			#address-cells = <1>;

> > > +			#size-cells = <0>;

> > > +		};  

> > 

> > Somewhat related: we shouldn't set the MMC speed flags in the drivers.

> > This is biting us on the already supported SoCs, so it would be great

> > to not repeat the same mistake with the new ones

> 

> Do you mean to list the "sd-uhs-sdr50" and friends properties here in

> the DT?

> What is the best practice here in terms putting them in the .dts vs.

> the .dtsi? Surely the controller has limits, but bad traces on a board

> could impose further restrictions, right?

>

> Though that's probably rare, so it sounds like a lot of churn to list

> them in every board DT. So can we list everything in here (.dtsi), then

> delete in those affected boards only?


Yeah, I completely agree :)

Maxime
Maxime Ripard Dec. 14, 2020, 2:14 p.m. UTC | #5 
On Mon, Dec 14, 2020 at 09:28:36PM +0800, Chen-Yu Tsai wrote:
> On Mon, Dec 14, 2020 at 8:53 PM Andre Przywara <andre.przywara@arm.com> wrote:

> >

> > On Mon, 14 Dec 2020 10:58:31 +0100

> > Maxime Ripard <maxime@cerno.tech> wrote:

> >

> > Hi,

> >

> > > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:

> > > > +   reserved-memory {

> > > > +           #address-cells = <2>;

> > > > +           #size-cells = <2>;

> > > > +           ranges;

> > > > +

> > > > +           /* 512KiB reserved for ARM Trusted Firmware (BL31)

> > > > */

> > > > +           secmon_reserved: secmon@40000000 {

> > > > +                   reg = <0x0 0x40000000 0x0 0x80000>;

> > > > +                   no-map;

> > > > +           };

> > > > +   };

> > >

> > > This should still be set by the firmware

> > >

> > > > +           mmc0: mmc@4020000 {

> > > > +                   compatible = "allwinner,sun50i-h616-mmc",

> > > > +                                "allwinner,sun50i-a100-mmc";

> > > > +                   reg = <0x04020000 0x1000>;

> > > > +                   clocks = <&ccu CLK_BUS_MMC0>, <&ccu

> > > > CLK_MMC0>;

> > > > +                   clock-names = "ahb", "mmc";

> > > > +                   resets = <&ccu RST_BUS_MMC0>;

> > > > +                   reset-names = "ahb";

> > > > +                   interrupts = <GIC_SPI 35

> > > > IRQ_TYPE_LEVEL_HIGH>;

> > > > +                   pinctrl-names = "default";

> > > > +                   pinctrl-0 = <&mmc0_pins>;

> > > > +                   status = "disabled";

> > > > +                   #address-cells = <1>;

> > > > +                   #size-cells = <0>;

> > > > +           };

> > >

> > > Somewhat related: we shouldn't set the MMC speed flags in the drivers.

> > > This is biting us on the already supported SoCs, so it would be great

> > > to not repeat the same mistake with the new ones

> >

> > Do you mean to list the "sd-uhs-sdr50" and friends properties here in

> > the DT?

> > What is the best practice here in terms putting them in the .dts vs.

> > the .dtsi? Surely the controller has limits, but bad traces on a board

> > could impose further restrictions, right?

> > Though that's probably rare, so it sounds like a lot of churn to list

> > them in every board DT. So can we list everything in here (.dtsi), then

> > delete in those affected boards only?

> 

> The driver will most certainly already have the basic high speed modes

> enabled. Or we can list them in the .dtsi file.


I'd list them all in the DTSI, trying to be smart has bitten us already
so I'd like to avoid it as much as possible.

And if we find a better way, we can set it in the driver if it's in the
DTSI already. doing the opposite would be harder

Maxime
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 000000000000..7202632b061b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,715 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 512KiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved: secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x80000>;
+			no-map;
+		};
+	};
+
+	osc24M: osc24M_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		arm,no-tick-in-suspend;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun50i-h616-system-control";
+			reg = <0x03000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@28000 {
+				compatible = "mmio-sram";
+				reg = <0x00028000 0x30000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00028000 0x30000>;
+			};
+		};
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h616-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		watchdog: watchdog@30090a0 {
+			compatible = "allwinner,sun50i-h616-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x030090a0 0x20>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h616-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			ext_rgmii_pins: rgmii-pins {
+				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+				       "PI5", "PI7", "PI8", "PI9", "PI10",
+				       "PI11", "PI12", "PI13", "PI14", "PI15",
+				       "PI16";
+				function = "emac0";
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PI6", "PI7";
+				function = "i2c0";
+			};
+
+			i2c3_ph_pins: i2c3-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c3";
+			};
+
+			ir_rx_pin: ir_rx_pin {
+				pins = "PH10";
+				function = "ir_rx";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			spi0_pins: spi0-pins {
+				pins = "PC0", "PC2", "PC3", "PC4";
+				function = "spi0";
+			};
+
+			spi1_pins: spi1-pins {
+				pins = "PH6", "PH7", "PH8";
+				function = "spi1";
+			};
+
+			spi1_cs_pin: spi1-cs-pin {
+				pins = "PH5";
+				function = "spi1";
+			};
+
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun50i-h616-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@5001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001400 0x400>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c4: i2c@5003000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05003000 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@5010000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05010000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@5011000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05011000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac0: ethernet@5020000 {
+			compatible = "allwinner,sun50i-h616-emac",
+				     "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x05020000 0x10000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC0>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC0>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		emac1: ethernet@5030000 {
+			compatible = "allwinner,sun50i-h616-emac";
+			syscon = <&syscon 1>;
+			reg = <0x05030000 0x10000>;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC1>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC1>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+
+			mdio1: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		usbotg: usb@5100000 {
+			compatible = "allwinner,sun50i-h616-musb",
+				     "allwinner,sun8i-h3-musb";
+			reg = <0x05100000 0x0400>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mc";
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			extcon = <&usbphy 0>;
+			status = "disabled";
+		};
+
+		usbphy: phy@5100400 {
+			compatible = "allwinner,sun50i-h616-usb-phy";
+			reg = <0x05100400 0x24>,
+			      <0x05101800 0x14>,
+			      <0x05200800 0x14>,
+			      <0x05310800 0x14>,
+			      <0x05311800 0x14>;
+			reg-names = "phy_ctrl",
+				    "pmu0",
+				    "pmu1",
+				    "pmu2",
+				    "pmu3";
+			clocks = <&ccu CLK_USB_PHY0>,
+				 <&ccu CLK_USB_PHY1>,
+				 <&ccu CLK_USB_PHY2>,
+				 <&ccu CLK_USB_PHY3>;
+			clock-names = "usb0_phy",
+				      "usb1_phy",
+				      "usb2_phy",
+				      "usb3_phy";
+			resets = <&ccu RST_USB_PHY0>,
+				 <&ccu RST_USB_PHY1>,
+				 <&ccu RST_USB_PHY2>,
+				 <&ccu RST_USB_PHY3>;
+			reset-names = "usb0_reset",
+				      "usb1_reset",
+				      "usb2_reset",
+				      "usb3_reset";
+			status = "disabled";
+			#phy-cells = <1>;
+		};
+
+		ehci0: usb@5101000 {
+			compatible = "allwinner,sun50i-h616-ehci",
+				     "generic-ehci";
+			reg = <0x05101000 0x100>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_BUS_EHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_OHCI0>,
+				 <&ccu RST_BUS_EHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci0: usb@5101400 {
+			compatible = "allwinner,sun50i-h616-ohci",
+				     "generic-ohci";
+			reg = <0x05101400 0x100>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ehci1: usb@5200000 {
+			compatible = "allwinner,sun50i-h616-ehci",
+				     "generic-ehci";
+			reg = <0x05200000 0x100>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_BUS_EHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>,
+				 <&ccu RST_BUS_EHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci1: usb@5200400 {
+			compatible = "allwinner,sun50i-h616-ohci",
+				     "generic-ohci";
+			reg = <0x05200400 0x100>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ehci2: usb@5310000 {
+			compatible = "allwinner,sun50i-h616-ehci",
+				     "generic-ehci";
+			reg = <0x05310000 0x100>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI2>,
+				 <&ccu CLK_BUS_EHCI2>,
+				 <&ccu CLK_USB_OHCI2>;
+			resets = <&ccu RST_BUS_OHCI2>,
+				 <&ccu RST_BUS_EHCI2>;
+			phys = <&usbphy 2>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci2: usb@5310400 {
+			compatible = "allwinner,sun50i-h616-ohci",
+				     "generic-ohci";
+			reg = <0x05310400 0x100>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI2>,
+				 <&ccu CLK_USB_OHCI2>;
+			resets = <&ccu RST_BUS_OHCI2>;
+			phys = <&usbphy 2>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ehci3: usb@5311000 {
+			compatible = "allwinner,sun50i-h616-ehci",
+				     "generic-ehci";
+			reg = <0x05311000 0x100>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI3>,
+				 <&ccu CLK_BUS_EHCI3>,
+				 <&ccu CLK_USB_OHCI3>;
+			resets = <&ccu RST_BUS_OHCI3>,
+				 <&ccu RST_BUS_EHCI3>;
+			phys = <&usbphy 3>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci3: usb@5311400 {
+			compatible = "allwinner,sun50i-h616-ohci",
+				     "generic-ohci";
+			reg = <0x05311400 0x100>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI3>,
+				 <&ccu CLK_USB_OHCI3>;
+			resets = <&ccu RST_BUS_OHCI3>;
+			phys = <&usbphy 3>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		rtc: rtc@7000000 {
+			compatible = "allwinner,sun50i-h616-rtc",
+				     "allwinner,sun50i-h6-rtc";
+			reg = <0x07000000 0x400>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out", "iosc";
+			#clock-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-h616-r-ccu";
+			reg = <0x07010000 0x400>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-h616-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+			};
+		};
+
+		ir: ir@7040000 {
+				compatible = "allwinner,sun50i-h616-ir",
+					     "allwinner,sun6i-a31-ir";
+				reg = <0x07040000 0x400>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&r_ccu CLK_R_APB1_IR>,
+					 <&r_ccu CLK_IR>;
+				clock-names = "apb", "ir";
+				resets = <&r_ccu RST_R_APB1_IR>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ir_rx_pin>;
+				status = "disabled";
+		};
+
+		r_i2c: i2c@7081400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			resets = <&r_ccu RST_R_APB2_I2C>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};