@@ -1081,7 +1081,7 @@ int usb_set_isoch_delay(struct usb_device *dev)
if (dev->speed < USB_SPEED_SUPER)
return 0;
- return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
+ return usb_control_msg_send(dev, 0,
USB_REQ_SET_ISOCH_DELAY,
USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
dev->hub_delay, 0, NULL, 0,
@@ -1203,13 +1203,13 @@ int usb_clear_halt(struct usb_device *dev, int pipe)
* (like some ibmcam model 1 units) seem to expect hosts to make
* this request for iso endpoints, which can't halt!
*/
- result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
- USB_REQ_CLEAR_FEATURE, USB_RECIP_ENDPOINT,
- USB_ENDPOINT_HALT, endp, NULL, 0,
- USB_CTRL_SET_TIMEOUT);
+ result = usb_control_msg_send(dev, 0,
+ USB_REQ_CLEAR_FEATURE, USB_RECIP_ENDPOINT,
+ USB_ENDPOINT_HALT, endp, NULL, 0,
+ USB_CTRL_SET_TIMEOUT);
/* don't un-halt or force to DATA0 except on success */
- if (result < 0)
+ if (result)
return result;
/* NOTE: seems like Microsoft and Apple don't bother verifying
@@ -1558,9 +1558,10 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)
if (dev->quirks & USB_QUIRK_NO_SET_INTF)
ret = -EPIPE;
else
- ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
- USB_REQ_SET_INTERFACE, USB_RECIP_INTERFACE,
- alternate, interface, NULL, 0, 5000);
+ ret = usb_control_msg_send(dev, 0,
+ USB_REQ_SET_INTERFACE,
+ USB_RECIP_INTERFACE, alternate,
+ interface, NULL, 0, 5000);
/* 9.4.10 says devices don't need this and are free to STALL the
* request if the interface only has one alternate setting.
@@ -1570,7 +1571,7 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)
"manual set_interface for iface %d, alt %d\n",
interface, alternate);
manual = 1;
- } else if (ret < 0) {
+ } else if (ret) {
/* Re-instate the old alt setting */
usb_hcd_alloc_bandwidth(dev, NULL, alt, iface->cur_altsetting);
usb_enable_lpm(dev);
@@ -1718,11 +1719,10 @@ int usb_reset_configuration(struct usb_device *dev)
mutex_unlock(hcd->bandwidth_mutex);
return retval;
}
- retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
- USB_REQ_SET_CONFIGURATION, 0,
- config->desc.bConfigurationValue, 0,
- NULL, 0, USB_CTRL_SET_TIMEOUT);
- if (retval < 0)
+ retval = usb_control_msg_send(dev, 0, USB_REQ_SET_CONFIGURATION, 0,
+ config->desc.bConfigurationValue, 0,
+ NULL, 0, USB_CTRL_SET_TIMEOUT);
+ if (retval)
goto reset_old_alts;
mutex_unlock(hcd->bandwidth_mutex);
@@ -2103,10 +2103,10 @@ int usb_set_configuration(struct usb_device *dev, int configuration)
}
kfree(new_interfaces);
- ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
- USB_REQ_SET_CONFIGURATION, 0, configuration, 0,
- NULL, 0, USB_CTRL_SET_TIMEOUT);
- if (ret < 0 && cp) {
+ ret = usb_control_msg_send(dev, 0, USB_REQ_SET_CONFIGURATION, 0,
+ configuration, 0, NULL, 0,
+ USB_CTRL_SET_TIMEOUT);
+ if (ret && cp) {
/*
* All the old state is gone, so what else can we do?
* The device is probably useless now anyway.
There are a few calls to usb_control_msg() that can be converted to use usb_control_msg_send() instead, so do that in order to make the error checking a bit simpler. Cc: Alan Stern <stern@rowland.harvard.edu> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: linux-usb@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> --- v2: - no change from v1 drivers/usb/core/message.c | 38 +++++++++++++++++++------------------- 1 file changed, 19 insertions(+), 19 deletions(-)