@@ -1600,7 +1600,6 @@ source "board/freescale/p1023rdb/Kconfig"
source "board/freescale/p1_twr/Kconfig"
source "board/freescale/qemu-ppce500/Kconfig"
source "board/freescale/t102xqds/Kconfig"
-source "board/freescale/t102xrdb/Kconfig"
source "board/freescale/t1040qds/Kconfig"
source "board/freescale/t104xrdb/Kconfig"
source "board/freescale/t208xqds/Kconfig"
deleted file mode 100644
@@ -1,14 +0,0 @@
-if TARGET_T1023RDB || TARGET_T1024RDB
-
-config SYS_BOARD
- default "t102xrdb"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "T102xRDB"
-
-source "board/freescale/common/Kconfig"
-
-endif
deleted file mode 100644
@@ -1,15 +0,0 @@
-T102XRDB BOARD
-#M: Shengzhou Liu <Shengzhou.Liu at freescale.com>
-S: Orphan (since 2018-05)
-F: board/freescale/t102xrdb/
-F: include/configs/T102xRDB.h
-F: configs/T1024RDB_defconfig
-F: configs/T1024RDB_NAND_defconfig
-F: configs/T1024RDB_SDCARD_defconfig
-F: configs/T1024RDB_SPIFLASH_defconfig
-F: configs/T1024RDB_SECURE_BOOT_defconfig
-F: configs/T1023RDB_defconfig
-F: configs/T1023RDB_NAND_defconfig
-F: configs/T1023RDB_SDCARD_defconfig
-F: configs/T1023RDB_SPIFLASH_defconfig
-F: configs/T1023RDB_SECURE_BOOT_defconfig
deleted file mode 100644
@@ -1,17 +0,0 @@
-#
-# Copyright 2014 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
-else
-obj-y += t102xrdb.o
-obj-$(CONFIG_TARGET_T1024RDB) += cpld.o
-obj-y += eth_t102xrdb.o
-obj-$(CONFIG_PCI) += pci.o
-endif
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
deleted file mode 100644
@@ -1,340 +0,0 @@
-T1024 SoC Overview
-------------------
-The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
-combines two or one 64-bit Power Architecture e5500 core respectively with high
-performance datapath acceleration logic, and network peripheral bus interfaces
-required for networking and telecommunications. This processor can be used in
-applications such as enterprise WLAN access points, routers, switches, firewall
-and other packet processing intensive small enterprise and branch office appliances,
-and general-purpose embedded computing. Its high level of integration offers
-significant performance benefits and greatly helps to simplify board design.
-
-
-The T1024 SoC includes the following function and features:
-- two e5500 cores, each with a private 256 KB L2 cache
- - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
- - Three levels of instructions: User, supervisor, and hypervisor
- - Independent boot and reset
- - Secure boot capability
-- 256 KB shared L3 CoreNet platform cache (CPC)
-- Interconnect CoreNet platform
- - CoreNet coherency manager supporting coherent and noncoherent transactions
- with prioritization and bandwidth allocation amongst CoreNet endpoints
- - 150 Gbps coherent read bandwidth
-- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
-- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
- - Packet parsing, classification, and distribution
- - Queue management for scheduling, packet sequencing, and congestion management
- - Cryptography Acceleration (SEC 5.x)
- - IEEE 1588 support
- - Hardware buffer management for buffer allocation and deallocation
- - MACSEC on DPAA-based Ethernet ports
-- Ethernet interfaces
- - Four 1 Gbps Ethernet controllers
-- Parallel Ethernet interfaces
- - Two RGMII interfaces
-- High speed peripheral interfaces
- - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
- - One SATA controller supporting 1.5 and 3.0 Gb/s operation
- - One QSGMII interface
- - Four SGMII interface supporting 1000 Mbps
- - Three SGMII interfaces supporting up to 2500 Mbps
- - 10GbE XFI or 10Base-KR interface
-- Additional peripheral interfaces
- - Two USB 2.0 controllers with integrated PHY
- - SD/eSDHC/eMMC
- - eSPI controller
- - Four I2C controllers
- - Four UARTs
- - Four GPIO controllers
- - Integrated flash controller (IFC)
- - LCD interface (DIU) with 12 bit dual data rate
-- Multicore programmable interrupt controller (PIC)
-- Two 8-channel DMA engines
-- Single source clocking implementation
-- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
-- QUICC Engine block
- - 32-bit RISC controller for flexible support of the communications peripherals
- - Serial DMA channel for receive and transmit on all serial channels
- - Two universal communication controllers, supporting TDM, HDLC, and UART
-
-T1023 Personality
-------------------
-T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
-unavailable deep sleep. Rest of the blocks are almost same as T1024.
-Differences between T1024 and T1023
-Feature T1024 T1023
-QUICC Engine: yes no
-DIU: yes no
-Deep Sleep: yes no
-I2C controller: 4 3
-DDR: 64-bit 32-bit
-IFC: 32-bit 28-bit
-Package: 23x23 19x19
-
-
-T1024RDB board Overview
------------------------
- - Ethernet
- - Two on-board 10M/100M/1G bps RGMII ethernet ports
- - One on-board 10G bps Base-T port.
- - DDR Memory
- - Supports 64-bit 4GB DDR3L DIMM
- - PCIe
- - One on-board PCIe slot.
- - Two on-board PCIe Mini-PCIe connectors.
- - IFC/Local Bus
- - NOR: 128MB 16-bit NOR Flash
- - NAND: 1GB 8-bit NAND flash
- - CPLD: for system controlling with programable header on-board
- - USB
- - Supports two USB 2.0 ports with integrated PHYs
- - Two type A ports with 5V at 1.5A per port.
- - SDHC
- - one SD connector supporting 1.8V/3.3V via J53.
- - SPI
- - On-board 64MB SPI flash
- - Other
- - Two Serial ports
- - Four I2C ports
-
-
-T1023RDB board Overview
------------------------
-- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
-- CoreNet fabric supporting coherent and noncoherent transactions with
- prioritization and bandwidth allocation
-- SDRAM memory: 2GB Micron MT40A512M8HX unbuffered 32-bit DDR4 w/o ECC
-- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
-- Ethernet interfaces:
- - one 1G RGMII port on-board(RTL8211FS PHY)
- - one 1G SGMII port on-board(RTL8211FS PHY)
- - one 2.5G SGMII port on-board(AQR105 PHY)
-- PCIe: Two Mini-PCIe connectors on-board.
-- SerDes: 4 lanes up to 10.3125GHz
-- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
-- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
-- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
-- USB: one Type-A USB 2.0 port with internal PHY
-- eSDHC: support SD/MMC and eMMC card
-- 256Kbit M24256 I2C EEPROM
-- RTC: Real-time clock DS1339U on I2C bus
-- UART: one serial port on-board with RJ45 connector
-- Debugging: JTAG/COP for T1023 debugging
-
-
-Memory map on T1024RDB
-----------------------
-Start Address End Address Description Size
-0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
-0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
-0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
-0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
-0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
-0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
-0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
-0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
-0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
-0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
-0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
-0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
-0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
-0x0_0000_0000 0x0_ffff_ffff DDR 4GB
-
-
-128MB NOR Flash Memory Layout
------------------------------
-Start Address End Address Definition Max size
-0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB
-0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB
-0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
-0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
-0xED300000 0xEFDFFFFF rootfs (alt bank) 44MB
-0xED000000 0xED2FFFFF Guest image #3 (alternate bank) 3MB
-0xECD00000 0xECFFFFFF Guest image #2 (alternate bank) 3MB
-0xECA00000 0xECCFFFFF Guest image #1 (alternate bank) 3MB
-0xEC900000 0xEC9FFFFF HV config device tree(alt bank) 1MB
-0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
-0xEC700000 0xEC7FFFFF HV.uImage (alternate bank) 1MB
-0xEC020000 0xEC6FFFFF Linux.uImage (alt bank) ~7MB
-0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
-0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB
-0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB
-0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
-0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
-0xE9300000 0xEBDFFFFF rootfs (current bank) 44MB
-0xE9000000 0xE92FFFFF Guest image #3 (current bank) 3MB
-0xE8D00000 0xE8FFFFFF Guest image #2 (current bank) 3MB
-0xE8A00000 0xE8CFFFFF Guest image #1 (current bank) 3MB
-0xE8900000 0xE89FFFFF HV config device tree(cur bank) 1MB
-0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
-0xE8700000 0xE87FFFFF HV.uImage (current bank) 1MB
-0xE8020000 0xE86FFFFF Linux.uImage (current bank) ~7MB
-0xE8000000 0xE801FFFF RCW (current bank) 128KB
-
-
-T1024/T1023 Clock frequency
----------------------------
-BIN Core DDR Platform FMan
-Bin1: 1400MHz 1600MT/s 400MHz 700MHz
-Bin2: 1200MHz 1600MT/s 400MHz 600MHz
-Bin3: 1000MHz 1600MT/s 400MHz 500MHz
-
-
-Software configurations and board settings
-------------------------------------------
-1. NOR boot:
- a. build NOR boot image
- $ make T1024RDB_defconfig
- $ make
- b. program u-boot.bin image to NOR flash
- => tftp 1000000 u-boot.bin
- => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
- on T1024RDB:
- set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
- on T1023RDB:
- set SW1[1:8] = '00010111', SW2[1] = '1', SW3[4] = '0' for NOR boot
-
- Switching between default bank0 and alternate bank4 on NOR flash
- To change boot source to vbank4:
- on T1024RDB:
- via software: run command 'cpld reset altbank' in U-Boot.
- via DIP-switch: set SW3[5:7] = '100'
- on T1023RDB:
- via software: run command 'switch bank4' in U-Boot.
- via DIP-switch: set SW3[5:7] = '100'
-
- To change boot source to vbank0:
- on T1024RDB:
- via software: run command 'cpld reset' in U-Boot.
- via DIP-Switch: set SW3[5:7] = '000'
- on T1023RDB:
- via software: run command 'switch bank0' in U-Boot.
- via DIP-switch: set SW3[5:7] = '000'
-
-2. NAND Boot:
- a. build PBL image for NAND boot
- $ make T1024RDB_NAND_defconfig
- $ make
- b. program u-boot-with-spl-pbl.bin to NAND flash
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => nand erase 0 $filesize
- => nand write 1000000 0 $filesize
- set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
-
-3. SPI Boot:
- a. build PBL image for SPI boot
- $ make T1024RDB_SPIFLASH_defconfig
- $ make
- b. program u-boot-with-spl-pbl.bin to SPI flash
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => sf probe 0
- => sf erase 0 100000
- => sf write 1000000 0 $filesize
- => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
- => sf erase 100000 100000
- => sf write 1000000 110000 20000
- set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
-
-4. SD Boot:
- a. build PBL image for SD boot
- $ make T1024RDB_SDCARD_defconfig
- $ make
- b. program u-boot-with-spl-pbl.bin to SD/MMC card
- => tftp 1000000 u-boot-with-spl-pbl.bin
- => mmc write 1000000 8 0x7f0
- => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
- => mmc write 1000000 0x820 80
- set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
-
- SW3[3] = '1' for SD card(or 'switch sd' by software)
- SW3[3] = '0' for eMMC (or 'switch emmc' by software)
-
-
-device tree support and how to enable it for different configs
---------------------------------------------------------------
-device tree support is available for t1024rdb for below mentioned boot,
-1. nor boot
-2. nand boot
-3. sd boot
-4. spiflash boot
-
-to enable device tree support for other boot, below configs need to be
-enabled in relative defconfig file,
-1. config_default_device_tree="t1024rdb" (change default device tree name if required)
-2. config_of_control
-3. config_mpc85xx_have_reset_vector if reset vector is located at
- config_reset_vector_address - 0xffc
-
-if device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for nor boot.
-2. use 'u-boot-with-spl-pbl.bin' for other boot.
-
-2-stage NAND/SPI/SD boot loader
--------------------------------
-PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
-SPL further initializes DDR using SPD and environment variables
-and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to U-Boot for futher booting.
-
-SPL has following features:
- - Executes within 256K
- - No relocation required
-
-Run time view of SPL framework
--------------------------------------------------
-|Area | Address |
--------------------------------------------------
-|SecureBoot header | 0xFFFC0000 (32KB) |
--------------------------------------------------
-|GD, BD | 0xFFFC8000 (4KB) |
--------------------------------------------------
-|ENV | 0xFFFC9000 (8KB) |
--------------------------------------------------
-|HEAP | 0xFFFCB000 (30KB) |
--------------------------------------------------
-|STACK | 0xFFFD8000 (22KB) |
--------------------------------------------------
-|U-Boot SPL | 0xFFFD8000 (160KB) |
--------------------------------------------------
-
-NAND Flash memory Map on T1024RDB
--------------------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot 1MB(2 block)
-0x100000 0x17FFFF U-Boot env 512KB(1 block)
-0x180000 0x1FFFFF FMAN Ucode 512KB(1 block)
-0x200000 0x27FFFF QE Firmware 512KB(1 block)
-
-
-NAND Flash memory Map on T1023RDB
-----------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot 1MB
-0x100000 0x15FFFF U-Boot env 8KB
-0x160000 0x17FFFF FMAN Ucode 128KB
-
-
-SD Card memory Map on T102xRDB
-----------------------------------------------------
-Block #blocks Definition Size
-0x008 2048 U-Boot img 1MB
-0x800 0016 U-Boot env 8KB
-0x820 0256 FMAN Ucode 128KB
-0x920 0256 QE Firmware 128KB(only T1024RDB)
-
-
-64MB SPI Flash memory Map on T102xRDB
-----------------------------------------------------
-Start End Definition Size
-0x000000 0x0FFFFF U-Boot img 1MB
-0x100000 0x101FFF U-Boot env 8KB
-0x110000 0x12FFFF FMAN Ucode 128KB
-0x130000 0x14FFFF QE Firmware 128KB(only T1024RDB)
-0x300000 0x3FFFFF device tree 128KB
-0x400000 0x9FFFFF Linux kernel 6MB
-0xa00000 0x3FFFFFF rootfs 54MB
-
-
-For more details, please refer to T1024RDB/T1023RDB User Guide
-and Freescale QorIQ SDK Infocenter document.
deleted file mode 100644
@@ -1,102 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/**
- * Copyright 2014 Freescale Semiconductor
- *
- * Freescale T1024RDB board-specific CPLD controlling supports.
- *
- * The following macros need to be defined:
- */
-
-#include <common.h>
-#include <command.h>
-#include <asm/io.h>
-#include "cpld.h"
-
-u8 cpld_read(unsigned int reg)
-{
- void *p = (void *)CONFIG_SYS_CPLD_BASE;
-
- return in_8(p + reg);
-}
-
-void cpld_write(unsigned int reg, u8 value)
-{
- void *p = (void *)CONFIG_SYS_CPLD_BASE;
-
- out_8(p + reg, value);
-}
-
-/**
- * Set the boot bank to the alternate bank
- */
-void cpld_set_altbank(void)
-{
- u8 reg = CPLD_READ(flash_csr);
-
- reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK;
-
- CPLD_WRITE(flash_csr, reg);
- CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
-}
-
-/**
- * Set the boot bank to the default bank
- */
-void cpld_set_defbank(void)
-{
- u8 reg = CPLD_READ(flash_csr);
-
- reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK;
-
- CPLD_WRITE(flash_csr, reg);
- CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
-}
-
-static void cpld_dump_regs(void)
-{
- printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver));
- printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub));
- printf("hw_ver = 0x%02x\n", CPLD_READ(hw_ver));
- printf("sw_ver = 0x%02x\n", CPLD_READ(sw_ver));
- printf("reset_ctl1 = 0x%02x\n", CPLD_READ(reset_ctl1));
- printf("reset_ctl2 = 0x%02x\n", CPLD_READ(reset_ctl2));
- printf("int_status = 0x%02x\n", CPLD_READ(int_status));
- printf("flash_csr = 0x%02x\n", CPLD_READ(flash_csr));
- printf("fan_ctl_status = 0x%02x\n", CPLD_READ(fan_ctl_status));
- printf("led_ctl_status = 0x%02x\n", CPLD_READ(led_ctl_status));
- printf("sfp_ctl_status = 0x%02x\n", CPLD_READ(sfp_ctl_status));
- printf("misc_ctl_status = 0x%02x\n", CPLD_READ(misc_ctl_status));
- printf("boot_override = 0x%02x\n", CPLD_READ(boot_override));
- printf("boot_config1 = 0x%02x\n", CPLD_READ(boot_config1));
- printf("boot_config2 = 0x%02x\n", CPLD_READ(boot_config2));
- putc('\n');
-}
-
-int do_cpld(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
-{
- int rc = 0;
-
- if (argc <= 1)
- return cmd_usage(cmdtp);
-
- if (strcmp(argv[1], "reset") == 0) {
- if (strcmp(argv[2], "altbank") == 0)
- cpld_set_altbank();
- else
- cpld_set_defbank();
- } else if (strcmp(argv[1], "dump") == 0) {
- cpld_dump_regs();
- } else {
- rc = cmd_usage(cmdtp);
- }
-
- return rc;
-}
-
-U_BOOT_CMD(
- cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
- "Reset the board or alternate bank",
- "reset - hard reset to default bank\n"
- "cpld reset altbank - reset to alternate bank\n"
- "cpld dump - display the CPLD registers\n"
- );
deleted file mode 100644
@@ -1,48 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/**
- * Copyright 2014 Freescale Semiconductor
- *
- */
-
-struct cpld_data {
- u8 cpld_ver; /* 0x00 - CPLD Major Revision Register */
- u8 cpld_ver_sub; /* 0x01 - CPLD Minor Revision Register */
- u8 hw_ver; /* 0x02 - Hardware Revision Register */
- u8 sw_ver; /* 0x03 - Software Revision register */
- u8 res0[12]; /* 0x04 - 0x0F - not used */
- u8 reset_ctl1; /* 0x10 - Reset control Register1 */
- u8 reset_ctl2; /* 0x11 - Reset control Register2 */
- u8 int_status; /* 0x12 - Interrupt status Register */
- u8 flash_csr; /* 0x13 - Flash control and status register */
- u8 fan_ctl_status; /* 0x14 - Fan control and status register */
- u8 led_ctl_status; /* 0x15 - LED control and status register */
- u8 sfp_ctl_status; /* 0x16 - SFP control and status register */
- u8 misc_ctl_status; /* 0x17 - Miscellanies ctrl & status register*/
- u8 boot_override; /* 0x18 - Boot override register */
- u8 boot_config1; /* 0x19 - Boot config override register*/
- u8 boot_config2; /* 0x1A - Boot config override register*/
-} cpld_data_t;
-
-
-/* Pointer to the CPLD register set */
-
-u8 cpld_read(unsigned int reg);
-void cpld_write(unsigned int reg, u8 value);
-
-#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
-#define CPLD_WRITE(reg, value)\
- cpld_write(offsetof(struct cpld_data, reg), value)
-
-/* CPLD on IFC */
-#define CPLD_LBMAP_MASK 0x3F
-#define CPLD_BANK_SEL_MASK 0x07
-#define CPLD_BANK_OVERRIDE 0x40
-#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */
-#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */
-#define CPLD_LBMAP_RESET 0xFF
-#define CPLD_LBMAP_SHIFT 0x03
-#define CPLD_BOOT_SEL 0x80
-
-#define CPLD_PCIE_SGMII_MUX 0x80
-#define CPLD_OVERRIDE_BOOT_EN 0x01
-#define CPLD_OVERRIDE_MUX_EN 0x02 /* PCIE/2.5G-SGMII mux override enable */
deleted file mode 100644
@@ -1,257 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <init.h>
-#include <log.h>
-#include <asm/mmu.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include <asm/fsl_law.h>
-#include <asm/mpc85xx_gpio.h>
-#include <linux/delay.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct board_specific_parameters {
- u32 n_ranks;
- u32 datarate_mhz_high;
- u32 rank_gb;
- u32 clk_adjust;
- u32 wrlvl_start;
- u32 wrlvl_ctl_2;
- u32 wrlvl_ctl_3;
-};
-
-/*
- * datarate_mhz_high values need to be in ascending order
- */
-static const struct board_specific_parameters udimm0[] = {
- /*
- * memory controller 0
- * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
- * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
- */
- {2, 833, 0, 8, 6, 0x06060607, 0x08080807,},
- {2, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
- {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
- {1, 833, 0, 8, 6, 0x06060607, 0x08080807,},
- {1, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
- {1, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
- {}
-};
-
-static const struct board_specific_parameters *udimms[] = {
- udimm0,
-};
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
- ulong ddr_freq;
- struct cpu_type *cpu = gd->arch.cpu;
-
- if (ctrl_num > 1) {
- printf("Not supported controller number %d\n", ctrl_num);
- return;
- }
- if (!pdimm->n_ranks)
- return;
-
- pbsp = udimms[0];
-
- /* Get clk_adjust according to the board ddr freqency and n_banks
- * specified in board_specific_parameters table.
- */
- ddr_freq = get_ddr_freq(0) / 1000000;
- while (pbsp->datarate_mhz_high) {
- if (pbsp->n_ranks == pdimm->n_ranks &&
- (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
- if (ddr_freq <= pbsp->datarate_mhz_high) {
- popts->clk_adjust = pbsp->clk_adjust;
- popts->wrlvl_start = pbsp->wrlvl_start;
- popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
- popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
- goto found;
- }
- pbsp_highest = pbsp;
- }
- pbsp++;
- }
-
- if (pbsp_highest) {
- printf("Error: board specific timing not found\n");
- printf("for data rate %lu MT/s\n", ddr_freq);
- printf("Trying to use the highest speed (%u) parameters\n",
- pbsp_highest->datarate_mhz_high);
- popts->clk_adjust = pbsp_highest->clk_adjust;
- popts->wrlvl_start = pbsp_highest->wrlvl_start;
- popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
- popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
- } else {
- panic("DIMM is not supported by this board");
- }
-found:
- debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
- pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
- debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
- pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
- debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
- /*
- * Write leveling override
- */
- popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xf;
-
- /*
- * rtt and rtt_wr override
- */
- popts->rtt_override = 0;
-
- /* Enable ZQ calibration */
- popts->zq_en = 1;
-
- /* DHC_EN =1, ODT = 75 Ohm */
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF);
- popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF);
-
- /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
- * force DDR bus width to 32bit for T1023
- */
- if (cpu->soc_ver == SVR_T1023)
- popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
-
-#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
- /* for DDR bus 32bit test on T1024 */
- popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
-#endif
-
-#ifdef CONFIG_TARGET_T1023RDB
- popts->wrlvl_ctl_2 = 0x07070606;
- popts->half_strength_driver_enable = 1;
- popts->cpo_sample = 0x43;
-#elif defined(CONFIG_TARGET_T1024RDB)
- /* optimize cpo for erratum A-009942 */
- popts->cpo_sample = 0x52;
-#endif
-}
-
-#ifdef CONFIG_SYS_DDR_RAW_TIMING
-/* 2GB discrete DDR4 MT40A512M8HX on T1023RDB */
-dimm_params_t ddr_raw_timing = {
- .n_ranks = 1,
- .rank_density = 0x80000000,
- .capacity = 0x80000000,
- .primary_sdram_width = 32,
- .ec_sdram_width = 8,
- .registered_dimm = 0,
- .mirrored_dimm = 0,
- .n_row_addr = 15,
- .n_col_addr = 10,
- .bank_addr_bits = 2,
- .bank_group_bits = 2,
- .edc_config = 0,
- .burst_lengths_bitmask = 0x0c,
- .tckmin_x_ps = 938,
- .tckmax_ps = 1500,
- .caslat_x = 0x000DFA00,
- .taa_ps = 13500,
- .trcd_ps = 13500,
- .trp_ps = 13500,
- .tras_ps = 33000,
- .trc_ps = 46500,
- .trfc1_ps = 260000,
- .trfc2_ps = 160000,
- .trfc4_ps = 110000,
- .tfaw_ps = 25000,
- .trrds_ps = 3700,
- .trrdl_ps = 5300,
- .tccdl_ps = 5355,
- .refresh_rate_ps = 7800000,
- .dq_mapping[0] = 0x0,
- .dq_mapping[1] = 0x0,
- .dq_mapping[2] = 0x0,
- .dq_mapping[3] = 0x0,
- .dq_mapping[4] = 0x0,
- .dq_mapping[5] = 0x0,
- .dq_mapping[6] = 0x0,
- .dq_mapping[7] = 0x0,
- .dq_mapping[8] = 0x0,
- .dq_mapping[9] = 0x0,
- .dq_mapping[10] = 0x0,
- .dq_mapping[11] = 0x0,
- .dq_mapping[12] = 0x0,
- .dq_mapping[13] = 0x0,
- .dq_mapping[14] = 0x0,
- .dq_mapping[15] = 0x0,
- .dq_mapping[16] = 0x0,
- .dq_mapping[17] = 0x0,
- .dq_mapping_ors = 1,
-};
-
-int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
- unsigned int controller_number,
- unsigned int dimm_number)
-{
- const char dimm_model[] = "Fixed DDR4 on board";
-
- if (((controller_number == 0) && (dimm_number == 0)) ||
- ((controller_number == 1) && (dimm_number == 0))) {
- memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
- memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
- memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
- }
-
- return 0;
-}
-#endif
-
-#if defined(CONFIG_DEEP_SLEEP)
-void board_mem_sleep_setup(void)
-{
- void __iomem *cpld_base = (void *)CONFIG_SYS_CPLD_BASE;
-
- /* does not provide HW signals for power management */
- clrbits_8(cpld_base + 0x17, 0x40);
- /* Disable MCKE isolation */
- gpio_set_value(2, 0);
- udelay(1);
-}
-#endif
-
-int dram_init(void)
-{
- phys_size_t dram_size;
-
-#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
-#ifndef CONFIG_SYS_DDR_RAW_TIMING
- puts("Initializing....using SPD\n");
-#endif
- dram_size = fsl_ddr_sdram();
-#else
- /* DDR has been initialised by first stage boot loader */
- dram_size = fsl_ddr_sdram_size();
-#endif
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
-
-#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
- fsl_dp_resume();
-#endif
-
- gd->ram_size = dram_size;
-
- return 0;
-}
deleted file mode 100644
@@ -1,146 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- *
- * Shengzhou Liu <Shengzhou.Liu at freescale.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <fdt_support.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_portals.h>
-#include <asm/fsl_liodn.h>
-#include <malloc.h>
-#include <fm_eth.h>
-#include <fsl_mdio.h>
-#include <miiphy.h>
-#include <phy.h>
-#include <fsl_dtsec.h>
-#include <asm/fsl_serdes.h>
-#include "../common/fman.h"
-
-int board_eth_init(bd_t *bis)
-{
-#if defined(CONFIG_FMAN_ENET)
- int i, interface;
- struct memac_mdio_info dtsec_mdio_info;
- struct memac_mdio_info tgec_mdio_info;
- struct mii_dev *dev;
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_s1;
-
- srds_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
- dtsec_mdio_info.regs =
- (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
-
- dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
-
- /* Register the 1G MDIO bus */
- fm_memac_mdio_init(bis, &dtsec_mdio_info);
-
- tgec_mdio_info.regs =
- (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
- tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
-
- /* Register the 10G MDIO bus */
- fm_memac_mdio_init(bis, &tgec_mdio_info);
-
- /* Set the on-board RGMII PHY address */
- fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
-
- switch (srds_s1) {
-#ifdef CONFIG_TARGET_T1024RDB
- case 0x95:
- /* set the on-board RGMII2 PHY */
- fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
-
- /* set 10G XFI with Aquantia AQR105 PHY */
- fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
- break;
-#endif
- case 0x6a:
- case 0x6b:
- case 0x77:
- case 0x135:
- /* set the on-board 2.5G SGMII AQR105 PHY */
- fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
-#ifdef CONFIG_TARGET_T1023RDB
- /* set the on-board 1G SGMII RTL8211F PHY */
- fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
-#endif
- break;
- default:
- printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
- srds_s1);
- break;
- }
-
- for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
- interface = fm_info_get_enet_if(i);
- switch (interface) {
- case PHY_INTERFACE_MODE_RGMII:
- dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
- fm_info_set_mdio(i, dev);
- break;
- case PHY_INTERFACE_MODE_SGMII:
-#if defined(CONFIG_TARGET_T1023RDB)
- dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
-#elif defined(CONFIG_TARGET_T1024RDB)
- dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
-#endif
- fm_info_set_mdio(i, dev);
- break;
- case PHY_INTERFACE_MODE_SGMII_2500:
- dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
- fm_info_set_mdio(i, dev);
- break;
- default:
- break;
- }
- }
-
- for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
- switch (fm_info_get_enet_if(i)) {
- case PHY_INTERFACE_MODE_XGMII:
- dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
- fm_info_set_mdio(i, dev);
- break;
- default:
- break;
- }
- }
-
- cpu_eth_init(bis);
-#endif /* CONFIG_FMAN_ENET */
-
- return pci_eth_init(bis);
-}
-
-void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
- enum fm_port port, int offset)
-{
-#if defined(CONFIG_TARGET_T1024RDB)
- if (((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) ||
- (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII)) &&
- (port == FM1_DTSEC3)) {
- fdt_set_phy_handle(fdt, compat, addr, "sg_2500_aqr105_phy4");
- fdt_setprop_string(fdt, offset, "phy-connection-type",
- "sgmii-2500");
- fdt_status_disabled_by_alias(fdt, "xg_aqr105_phy3");
- }
-#endif
-}
-
-void fdt_fixup_board_enet(void *fdt)
-{
-}
deleted file mode 100644
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
-#ifdef CONFIG_MTD_NOR_FLASH
- SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
-#endif
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
-#endif
-#ifdef CONFIG_SYS_CPLD_BASE_PHYS
- SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE_PHYS
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
-#endif
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
deleted file mode 100644
@@ -1,25 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2007-2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <pci.h>
-#include <asm/fsl_pci.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <asm/fsl_serdes.h>
-
-#if !defined(CONFIG_DM_PCI)
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-
-void pci_of_setup(void *blob, bd_t *bd)
-{
- FT_FSL_PCI_SETUP;
-}
-#endif
deleted file mode 100644
@@ -1,143 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/* Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <clock_legacy.h>
-#include <console.h>
-#include <env_internal.h>
-#include <init.h>
-#include <malloc.h>
-#include <ns16550.h>
-#include <nand.h>
-#include <i2c.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <spi_flash.h>
-#include "../common/sleep.h"
-#include "../common/spl.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-phys_size_t get_effective_memsize(void)
-{
- return CONFIG_SYS_L3_SIZE;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- return CONFIG_SYS_CLK_FREQ;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- return CONFIG_DDR_CLK_FREQ;
-}
-
-#if defined(CONFIG_SPL_MMC_BOOT)
-#define GPIO1_SD_SEL 0x00020000
-int board_mmc_getcd(struct mmc *mmc)
-{
- ccsr_gpio_t __iomem *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val = in_be32(&pgpio->gpdat);
-
- /* GPIO1_14, 0: eMMC, 1: SD */
- val &= GPIO1_SD_SEL;
-
- return val ? -1 : 1;
-}
-
-int board_mmc_getwp(struct mmc *mmc)
-{
- ccsr_gpio_t __iomem *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val = in_be32(&pgpio->gpdat);
-
- val &= GPIO1_SD_SEL;
-
- return val ? -1 : 0;
-}
-#endif
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio, sys_clk, ccb_clk;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
- /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
- memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
-
- /* Update GD pointer */
- gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
-
- console_init_f();
-
-#ifdef CONFIG_DEEP_SLEEP
- /* disable the console if boot from deep sleep */
- if (is_warm_boot())
- fsl_dp_disable_console();
-#endif
-
- /* initialize selected port with appropriate baud rate */
- sys_clk = get_board_sys_clk();
- plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
- ccb_clk = sys_clk * plat_ratio / 2;
-
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- ccb_clk / 16 / CONFIG_BAUDRATE);
-
-#if defined(CONFIG_SPL_MMC_BOOT)
- puts("\nSD boot...\n");
-#elif defined(CONFIG_SPL_SPI_BOOT)
- puts("\nSPI boot...\n");
-#elif defined(CONFIG_SPL_NAND_BOOT)
- puts("\nNAND boot...\n");
-#endif
-
- relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- bd_t *bd;
-
- bd = (bd_t *)(gd + sizeof(gd_t));
- memset(bd, 0, sizeof(bd_t));
- gd->bd = bd;
- bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
- bd->bi_memsize = CONFIG_SYS_L3_SIZE;
-
- arch_cpu_init();
- get_clocks();
- mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
- CONFIG_SPL_RELOC_MALLOC_SIZE);
- gd->flags |= GD_FLG_FULL_MALLOC_INIT;
-
-#ifdef CONFIG_SPL_NAND_BOOT
- nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_initialize(bd);
- mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-#ifdef CONFIG_SPL_SPI_BOOT
- fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
- (uchar *)SPL_ENV_ADDR);
-#endif
-
- gd->env_addr = (ulong)(SPL_ENV_ADDR);
- gd->env_valid = ENV_VALID;
-
- i2c_init_all();
-
- dram_init();
-
-#ifdef CONFIG_SPL_MMC_BOOT
- mmc_boot();
-#elif defined(CONFIG_SPL_SPI_BOOT)
- fsl_spi_boot();
-#elif defined(CONFIG_SPL_NAND_BOOT)
- nand_boot();
-#endif
-}
deleted file mode 100644
@@ -1,8 +0,0 @@
-#PBL preamble and RCW header for T1023RDB
-aa55aa55 010e0100
-#SerDes Protocol: 0x77
-#Default Core=1200MHz, DDR=1600MT/s with single source clock
-0810000c 00000000 00000000 00000000
-3b800003 00000012 e8104000 21000000
-00000000 00000000 00000000 00022800
-00000130 04020200 00000000 00000006
deleted file mode 100644
@@ -1,8 +0,0 @@
-#PBL preamble and RCW header for T1023RDB
-aa55aa55 010e0100
-#SerDes Protocol: 0x77
-#Default Core=1200MHz, DDR=1600MT/s with single source clock
-0810000c 00000000 00000000 00000000
-3b800003 00000012 68104000 21000000
-00000000 00000000 00000000 00022800
-00000130 04020200 00000000 00000006
deleted file mode 100644
@@ -1,8 +0,0 @@
-#PBL preamble and RCW header for T1023RDB
-aa55aa55 010e0100
-#SerDes Protocol: 0x77
-#Default Core=1200MHz, DDR=1600MT/s with single source clock
-0810000c 00000000 00000000 00000000
-3b800003 00000012 58104000 21000000
-00000000 00000000 00000000 00022800
-00000130 04020200 00000000 00000006
deleted file mode 100644
@@ -1,8 +0,0 @@
-#PBL preamble and RCW header for T1024RDB
-aa55aa55 010e0100
-#SerDes Protocol: 0x95
-#Core/DDR: 1400Mhz/1600MT/s with single source clock
-0810000c 00000000 00000000 00000000
-4a800003 80000012 ec027000 21000000
-00000000 00000000 00000000 00030810
-00000000 0b005a08 00000000 00000006
deleted file mode 100644
@@ -1,26 +0,0 @@
-#PBI commands
-#Initialize CPC1
-09010000 00200400
-09138000 00000000
-091380c0 00000100
-#Configure CPC1 as 256KB SRAM
-09010100 00000000
-09010104 fffc0007
-09010f00 081e000d
-09010000 80000000
-#Configure LAW for CPC1
-09000cd0 00000000
-09000cd4 fffc0000
-09000cd8 81000011
-#Configure alternate space
-09000010 00000000
-09000014 ff000000
-09000018 81000000
-#Configure SPI controller
-09110000 80000403
-09110020 2d170008
-09110024 00100008
-09110028 00100008
-0911002c 00100008
-#Flush PBL data
-091380c0 000FFFFF
deleted file mode 100644
@@ -1,8 +0,0 @@
-#PBL preamble and RCW header for T1024RDB
-aa55aa55 010e0100
-#SerDes Protocol: 0x95
-#Core/DDR: 1400Mhz/1600MT/s with single source clock
-0810000c 00000000 00000000 00000000
-4a800003 80000012 6c027000 21000000
-00000000 00000000 00000000 00030810
-00000000 0b005a08 00000000 00000006
deleted file mode 100644
@@ -1,8 +0,0 @@
-#PBL preamble and RCW header for T1024RDB
-aa55aa55 010e0100
-#SerDes Protocol: 0x95
-#Core/DDR: 1400Mhz/1600MT/s with single source clock
-0810000c 00000000 00000000 00000000
-4a800003 80000012 5c027000 21000000
-00000000 00000000 00000000 00030810
-00000000 0b005a08 00000000 00000006
deleted file mode 100644
@@ -1,394 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <fdt_support.h>
-#include <i2c.h>
-#include <image.h>
-#include <init.h>
-#include <netdev.h>
-#include <linux/compiler.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_liodn.h>
-#include <fm_eth.h>
-#include "t102xrdb.h"
-#ifdef CONFIG_TARGET_T1024RDB
-#include "cpld.h"
-#elif defined(CONFIG_TARGET_T1023RDB)
-#include <i2c.h>
-#include <mmc.h>
-#endif
-#include "../common/sleep.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_TARGET_T1023RDB
-enum {
- GPIO1_SD_SEL = 0x00020000, /* GPIO1_14, 0: eMMC, 1:SD/MMC */
- GPIO1_EMMC_SEL,
- GPIO3_GET_VERSION, /* GPIO3_4/5, 00:RevB, 01: RevC */
- GPIO3_BRD_VER_MASK = 0x0c000000,
- GPIO3_OFFSET = 0x2000,
- I2C_GET_BANK,
- I2C_SET_BANK0,
- I2C_SET_BANK4,
-};
-#endif
-
-int checkboard(void)
-{
- struct cpu_type *cpu = gd->arch.cpu;
- static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
- ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_s1;
-
- srds_s1 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
- printf("Board: %sRDB, ", cpu->name);
-#if defined(CONFIG_TARGET_T1024RDB)
- printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
- CPLD_READ(hw_ver), CPLD_READ(sw_ver));
-#elif defined(CONFIG_TARGET_T1023RDB)
- printf("Rev%c, ", t1023rdb_ctrl(GPIO3_GET_VERSION) + 'B');
-#endif
- printf("boot from ");
-
-#ifdef CONFIG_SDCARD
- puts("SD/MMC\n");
-#elif CONFIG_SPIFLASH
- puts("SPI\n");
-#elif defined(CONFIG_TARGET_T1024RDB)
- u8 reg;
-
- reg = CPLD_READ(flash_csr);
-
- if (reg & CPLD_BOOT_SEL) {
- puts("NAND\n");
- } else {
- reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
- printf("NOR vBank%d\n", reg);
- }
-#elif defined(CONFIG_TARGET_T1023RDB)
-#ifdef CONFIG_MTD_RAW_NAND
- puts("NAND\n");
-#else
- printf("NOR vBank%d\n", t1023rdb_ctrl(I2C_GET_BANK));
-#endif
-#endif
-
- puts("SERDES Reference Clocks:\n");
- if (srds_s1 == 0x95)
- printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
- else
- printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[1]);
-
- return 0;
-}
-
-#ifdef CONFIG_TARGET_T1024RDB
-static void board_mux_lane(void)
-{
- ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 srds_prtcl_s1;
- u8 reg = CPLD_READ(misc_ctl_status);
-
- srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
- FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
- srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
-
- if (srds_prtcl_s1 == 0x95) {
- /* Route Lane B to PCIE */
- CPLD_WRITE(misc_ctl_status, reg & ~CPLD_PCIE_SGMII_MUX);
- } else {
- /* Route Lane B to SGMII */
- CPLD_WRITE(misc_ctl_status, reg | CPLD_PCIE_SGMII_MUX);
- }
- CPLD_WRITE(boot_override, CPLD_OVERRIDE_MUX_EN);
-}
-#endif
-
-int board_early_init_f(void)
-{
-#if defined(CONFIG_DEEP_SLEEP)
- if (is_warm_boot())
- fsl_dp_disable_console();
-#endif
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
-#ifdef CONFIG_SYS_FLASH_BASE
- const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- int flash_esel = find_tlb_idx((void *)flashbase, 1);
- /*
- * Remap Boot flash region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
- if (flash_esel == -1) {
- /* very unlikely unless something is messed up */
- puts("Error: Could not find TLB for FLASH BASE\n");
- flash_esel = 2; /* give our best effort to continue */
- } else {
- /* invalidate existing TLB entry for flash + promjet */
- disable_tlb(flash_esel);
- }
-
- set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_256M, 1);
-#endif
-
-#ifdef CONFIG_TARGET_T1024RDB
- board_mux_lane();
-#endif
-
- return 0;
-}
-
-unsigned long get_board_sys_clk(void)
-{
- return CONFIG_SYS_CLK_FREQ;
-}
-
-unsigned long get_board_ddr_clk(void)
-{
- return CONFIG_DDR_CLK_FREQ;
-}
-
-#ifdef CONFIG_TARGET_T1024RDB
-void board_reset(void)
-{
- CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
-}
-#endif
-
-int misc_init_r(void)
-{
- return 0;
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = env_get_bootm_low();
- size = env_get_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#ifdef CONFIG_PCI
- pci_of_setup(blob, bd);
-#endif
-
- fdt_fixup_liodn(blob);
- fsl_fdt_fixup_dr_usb(blob, bd);
-
-#ifdef CONFIG_SYS_DPAA_FMAN
- fdt_fixup_fman_ethernet(blob);
- fdt_fixup_board_enet(blob);
-#endif
-
-#ifdef CONFIG_TARGET_T1023RDB
- if (t1023rdb_ctrl(GPIO3_GET_VERSION) > 0)
- fdt_enable_nor(blob);
-#endif
-
- return 0;
-}
-
-#ifdef CONFIG_TARGET_T1023RDB
-/* Enable NOR flash for RevC */
-static void fdt_enable_nor(void *blob)
-{
- int nodeoff = fdt_node_offset_by_compatible(blob, 0, "cfi-flash");
-
- if (nodeoff >= 0)
- fdt_status_okay(blob, nodeoff);
- else
- printf("WARNING unable to set status for NOR\n");
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- ccsr_gpio_t __iomem *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val = in_be32(&pgpio->gpdat);
-
- /* GPIO1_14, 0: eMMC, 1: SD/MMC */
- val &= GPIO1_SD_SEL;
-
- return val ? -1 : 1;
-}
-
-int board_mmc_getwp(struct mmc *mmc)
-{
- ccsr_gpio_t __iomem *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- u32 val = in_be32(&pgpio->gpdat);
-
- val &= GPIO1_SD_SEL;
-
- return val ? -1 : 0;
-}
-
-static u32 t1023rdb_ctrl(u32 ctrl_type)
-{
- ccsr_gpio_t __iomem *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 val;
- u8 tmp;
- int bus_num = I2C_PCA6408_BUS_NUM;
-
-#ifdef CONFIG_DM_I2C
- struct udevice *dev;
- int ret;
-
- ret = i2c_get_chip_for_busnum(bus_num, I2C_PCA6408_ADDR,
- 1, &dev);
- if (ret) {
- printf("%s: Cannot find udev for a bus %d\n", __func__,
- bus_num);
- return ret;
- }
- switch (ctrl_type) {
- case GPIO1_SD_SEL:
- val = in_be32(&pgpio->gpdat);
- val |= GPIO1_SD_SEL;
- out_be32(&pgpio->gpdat, val);
- setbits_be32(&pgpio->gpdir, GPIO1_SD_SEL);
- break;
- case GPIO1_EMMC_SEL:
- val = in_be32(&pgpio->gpdat);
- val &= ~GPIO1_SD_SEL;
- out_be32(&pgpio->gpdat, val);
- setbits_be32(&pgpio->gpdir, GPIO1_SD_SEL);
- break;
- case GPIO3_GET_VERSION:
- pgpio = (ccsr_gpio_t *)(CONFIG_SYS_MPC85xx_GPIO_ADDR
- + GPIO3_OFFSET);
- val = in_be32(&pgpio->gpdat);
- val = ((val & GPIO3_BRD_VER_MASK) >> 26) & 0x3;
- if (val == 0x3) /* GPIO3_4/5 not used on RevB */
- val = 0;
- return val;
- case I2C_GET_BANK:
- dm_i2c_read(dev, 0, &tmp, 1);
- tmp &= 0x7;
- tmp = ((tmp & 1) << 2) | (tmp & 2) | ((tmp & 4) >> 2);
- return tmp;
- case I2C_SET_BANK0:
- tmp = 0x0;
- dm_i2c_write(dev, 1, &tmp, 1);
- tmp = 0xf8;
- dm_i2c_write(dev, 3, &tmp, 1);
- /* asserting HRESET_REQ */
- out_be32(&gur->rstcr, 0x2);
- break;
- case I2C_SET_BANK4:
- tmp = 0x1;
- dm_i2c_write(dev, 1, &tmp, 1);
- tmp = 0xf8;
- dm_i2c_write(dev, 3, &tmp, 1);
- out_be32(&gur->rstcr, 0x2);
- break;
- default:
- break;
- }
-#else
- u32 orig_bus;
-
- orig_bus = i2c_get_bus_num();
-
- switch (ctrl_type) {
- case GPIO1_SD_SEL:
- val = in_be32(&pgpio->gpdat);
- val |= GPIO1_SD_SEL;
- out_be32(&pgpio->gpdat, val);
- setbits_be32(&pgpio->gpdir, GPIO1_SD_SEL);
- break;
- case GPIO1_EMMC_SEL:
- val = in_be32(&pgpio->gpdat);
- val &= ~GPIO1_SD_SEL;
- out_be32(&pgpio->gpdat, val);
- setbits_be32(&pgpio->gpdir, GPIO1_SD_SEL);
- break;
- case GPIO3_GET_VERSION:
- pgpio = (ccsr_gpio_t *)(CONFIG_SYS_MPC85xx_GPIO_ADDR
- + GPIO3_OFFSET);
- val = in_be32(&pgpio->gpdat);
- val = ((val & GPIO3_BRD_VER_MASK) >> 26) & 0x3;
- if (val == 0x3) /* GPIO3_4/5 not used on RevB */
- val = 0;
- return val;
- case I2C_GET_BANK:
- i2c_set_bus_num(bus_num);
- i2c_read(I2C_PCA6408_ADDR, 0, 1, &tmp, 1);
- tmp &= 0x7;
- tmp = ((tmp & 1) << 2) | (tmp & 2) | ((tmp & 4) >> 2);
- i2c_set_bus_num(orig_bus);
- return tmp;
- case I2C_SET_BANK0:
- i2c_set_bus_num(bus_num);
- tmp = 0x0;
- i2c_write(I2C_PCA6408_ADDR, 1, 1, &tmp, 1);
- tmp = 0xf8;
- i2c_write(I2C_PCA6408_ADDR, 3, 1, &tmp, 1);
- /* asserting HRESET_REQ */
- out_be32(&gur->rstcr, 0x2);
- break;
- case I2C_SET_BANK4:
- i2c_set_bus_num(bus_num);
- tmp = 0x1;
- i2c_write(I2C_PCA6408_ADDR, 1, 1, &tmp, 1);
- tmp = 0xf8;
- i2c_write(I2C_PCA6408_ADDR, 3, 1, &tmp, 1);
- out_be32(&gur->rstcr, 0x2);
- break;
- default:
- break;
- }
-#endif
- return 0;
-}
-
-static int switch_cmd(struct cmd_tbl *cmdtp, int flag, int argc,
- char *const argv[])
-{
- if (argc < 2)
- return CMD_RET_USAGE;
- if (!strcmp(argv[1], "bank0"))
- t1023rdb_ctrl(I2C_SET_BANK0);
- else if (!strcmp(argv[1], "bank4") || !strcmp(argv[1], "altbank"))
- t1023rdb_ctrl(I2C_SET_BANK4);
- else if (!strcmp(argv[1], "sd"))
- t1023rdb_ctrl(GPIO1_SD_SEL);
- else if (!strcmp(argv[1], "emmc"))
- t1023rdb_ctrl(GPIO1_EMMC_SEL);
- else
- return CMD_RET_USAGE;
- return 0;
-}
-
-U_BOOT_CMD(
- switch, 2, 0, switch_cmd,
- "for bank0/bank4/sd/emmc switch control in runtime",
- "command (e.g. switch bank4)"
-);
-#endif
deleted file mode 100644
@@ -1,15 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#ifndef __T1024_RDB_H__
-#define __T1024_RDB_H__
-
-void fdt_fixup_board_enet(void *blob);
-void pci_of_setup(void *blob, bd_t *bd);
-#ifdef CONFIG_TARGET_T1023RDB
-static u32 t1023rdb_ctrl(u32 ctrl_type);
-static void fdt_enable_nor(void *blob);
-#endif
-#endif
deleted file mode 100644
@@ -1,116 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
- /*
- * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
- * SRAM is at 0xfffc0000, it covered the 0xfffff000.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_256K, 1),
-#else
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-#endif
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_16M, 1),
-
- /* *I*G* - Flash, localbus */
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
- MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
-#ifndef CONFIG_SPL_BUILD
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1G, 1),
-
- /* *I*G* - PCI I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256K, 1),
-
- /* Bman/Qman */
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 5, BOOKE_PAGESZ_16M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
- CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_16M, 1),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 7, BOOKE_PAGESZ_16M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
- CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 8, BOOKE_PAGESZ_16M, 1),
-#endif
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 9, BOOKE_PAGESZ_4M, 1),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_64K, 1),
-#endif
-#ifdef CONFIG_SYS_CPLD_BASE
- SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 11, BOOKE_PAGESZ_256K, 1),
-#endif
-
-#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 12, BOOKE_PAGESZ_1G, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
- CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 13, BOOKE_PAGESZ_1G, 1)
-#endif
- /* entry 14 and 15 has been used hard coded, they will be disabled
- * in cpu_init_f, so if needed more, will use entry 16 later.
- */
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
deleted file mode 100644
@@ -1,77 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x30001000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x140000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1023RDB=y
-CONFIG_SYS_CUSTOM_LDSCRIPT=y
-CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL"
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_FSL_CAAM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,74 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x30001000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1023RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD"
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_MMC_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_FSL_CAAM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,64 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_NXP_ESBC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1023RDB=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,77 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x30001000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1023RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH"
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_SPI_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_ADDR=0xFFFC9000
-CONFIG_FSL_CAAM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,61 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1023RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xEFF20000
-CONFIG_FSL_CAAM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,86 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x30001000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024RDB=y
-CONFIG_SYS_CUSTOM_LDSCRIPT=y
-CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL"
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t1024rdb"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
-CONFIG_DM_RTC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,83 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x30001000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD"
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_MMC_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t1024rdb"
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
-CONFIG_DM_RTC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,66 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_NXP_ESBC=y
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024RDB=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,86 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x30001000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_SPL_TEXT_BASE=0xFFFD8000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024RDB=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH"
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_SPI_BOOT=y
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t1024rdb"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_ADDR=0xFFFC9000
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
-CONFIG_DM_RTC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,71 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xEFF40000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_T1024RDB=y
-CONFIG_MPC85XX_HAVE_RESET_VECTOR=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_SILENT_CONSOLE=y
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_SYS_MEMTEST_START=0x00200000
-CONFIG_SYS_MEMTEST_END=0x00400000
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.1"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:1m(uboot),5m(kernel),128k(dtb),-(user)"
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="t1024rdb"
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xEFF20000
-CONFIG_DM=y
-CONFIG_FSL_CAAM=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_DM_I2C=y
-CONFIG_DM_MMC=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_MII=y
-CONFIG_DM_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_FSL=y
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_DM_RTC=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_USB=y
-CONFIG_DM_USB=y
deleted file mode 100644
@@ -1,721 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
- */
-
-/*
- * T1024/T1023 RDB board configuration file
- */
-
-#ifndef __T1024RDB_H
-#define __T1024RDB_H
-
-#include <linux/stringify.h>
-
-/* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-
-#define CONFIG_ENV_OVERWRITE
-
-/* support deep sleep */
-#ifdef CONFIG_ARCH_T1024
-#define CONFIG_DEEP_SLEEP
-#endif
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_PAD_TO 0x40000
-#define CONFIG_SPL_MAX_SIZE 0x28000
-#define RESET_VECTOR_OFFSET 0x27FFC
-#define BOOT_PAGE_OFFSET 0x27000
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_SKIP_RELOCATE
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
-#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x30000000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x30000000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_nand_rcw.cfg
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_nand_rcw.cfg
-#endif
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC
-#define CONFIG_SPL_SPI_FLASH_MINIMAL
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x30000000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x30000000)
-#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_spi_rcw.cfg
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_spi_rcw.cfg
-#endif
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC
-#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
-#define CONFIG_SYS_MMC_U_BOOT_DST (0x30000000)
-#define CONFIG_SYS_MMC_U_BOOT_START (0x30000000)
-#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#endif
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_sd_rcw.cfg
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_sd_rcw.cfg
-#endif
-#endif
-
-#endif /* CONFIG_RAMBOOT_PBL */
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-/* PCIe Boot - Master */
-#define CONFIG_SRIO_PCIE_BOOT_MASTER
-/*
- * for slave u-boot IMAGE instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
-#else
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
-#endif
-/*
- * for slave UCODE and ENV instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
-#else
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000
-#endif
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
-/* slave core release by master*/
-#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
-#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
-
-/* PCIe Boot - Slave */
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
-/* Set 1M boot space for PCIe boot */
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#endif
-
-#if defined(CONFIG_SPIFLASH)
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 100000000
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#endif
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
-#define CONFIG_SYS_L3_SIZE (256 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
-#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_DCSRBAR 0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-#endif
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x51
-#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_SDRAM_SIZE 2048
-#endif
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE 0xe8000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
-#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-
-/* NOR Flash Timing Params */
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(0) | \
- CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
-#endif
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
- FTIM0_NOR_TEADC(0x5) | \
- FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
- FTIM1_NOR_TRAD_NOR(0x1A) |\
- FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
- FTIM2_NOR_TCH(0x4) | \
- FTIM2_NOR_TWPH(0x0E) | \
- FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3 0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
-
-#ifdef CONFIG_TARGET_T1024RDB
-/* CPLD on IFC */
-#define CONFIG_SYS_CPLD_BASE 0xffdf0000
-#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
-#define CONFIG_SYS_CSPR2_EXT (0xf)
-#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
- | CSPR_PORT_SIZE_8 \
- | CSPR_MSEL_GPCM \
- | CSPR_V)
-#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
-#define CONFIG_SYS_CSOR2 0x0
-
-/* CPLD Timing parameters for IFC CS2 */
-#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
- FTIM0_GPCM_TEADC(0x0e) | \
- FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
- FTIM1_GPCM_TRAD(0x1f))
-#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
- FTIM2_GPCM_TCH(0x8) | \
- FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS2_FTIM3 0x0
-#endif
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE 0xff800000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
-
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
- | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
- | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL 3Bytes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
- | CSOR_NAND_SPRZ_128 /* Spare size = 128 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#endif
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW 11
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
-#if defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
-#endif
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#endif
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-
-/* Video */
-#undef CONFIG_FSL_DIU_FB /* RDB doesn't support DIU */
-#ifdef CONFIG_FSL_DIU_FB
-#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
-/*
- * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
- * disable empty flash sector detection, which is I/O-intensive.
- */
-#undef CONFIG_SYS_FLASH_EMPTY_INFO
-#endif
-
-/* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
-#endif
-
-#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
-#define I2C_PCA6408_BUS_NUM 1
-#define I2C_PCA6408_ADDR 0x20
-
-/* I2C bus multiplexer */
-#define I2C_MUX_CH_DEFAULT 0x8
-
-/*
- * RTC configuration
- */
-#define RTC
-#define CONFIG_RTC_DS1337 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * eSPI - Enhanced SPI
- */
-
-/*
- * General PCIe
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_PCIE1 /* PCIE controller 1 */
-#define CONFIG_PCIE2 /* PCIE controller 2 */
-#define CONFIG_PCIE3 /* PCIE controller 3 */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-
-#ifdef CONFIG_PCI
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#ifdef CONFIG_PCIE1
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-#endif
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#ifdef CONFIG_PCIE2
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
-#endif
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#ifdef CONFIG_PCIE3
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
-#endif
-
-#if !defined(CONFIG_DM_PCI)
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#endif /* CONFIG_PCI */
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
-
-/*
- * SDHC
- */
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_BMAN_NUM_PORTALS 10
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#else
-#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
-#endif
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
- CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
-#define CONFIG_SYS_QMAN_NUM_PORTALS 10
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
-#else
-#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
-#endif
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
- CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
-
-#define CONFIG_SYS_DPAA_FMAN
-
-/* Default address of microcode for the Linux FMan driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-#define CONFIG_SYS_QE_FW_ADDR 0x130000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
- */
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
-#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
-#elif defined(CONFIG_MTD_RAW_NAND)
-#if defined(CONFIG_TARGET_T1024RDB)
-#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_SYS_QE_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#endif
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#define CONFIG_SYS_QE_FW_ADDR 0xEFE00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#if defined(CONFIG_TARGET_T1024RDB)
-#define RGMII_PHY1_ADDR 0x2
-#define RGMII_PHY2_ADDR 0x6
-#define SGMII_AQR_PHY_ADDR 0x2
-#define FM1_10GEC1_PHY_ADDR 0x1
-#elif defined(CONFIG_TARGET_T1023RDB)
-#define RGMII_PHY1_ADDR 0x1
-#define SGMII_RTK_PHY_ADDR 0x3
-#define SGMII_AQR_PHY_ADDR 0x2
-#endif
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1 at DTSEC4"
-#endif
-
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */
-#define __USB_PHY_TYPE utmi
-
-#ifdef CONFIG_ARCH_T1024
-#define CONFIG_BOARDNAME t1024rdb
-#define BANK_INTLV cs0_cs1
-#else
-#define CONFIG_BOARDNAME t1023rdb
-#define BANK_INTLV null
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
- "bank_intlv=" __stringify(BANK_INTLV) "\0" \
- "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
- "ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
- "fdtfile=" __stringify(CONFIG_BOARDNAME) "/" \
- __stringify(CONFIG_BOARDNAME) ".dtb\0" \
- "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
- "bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
- "netdev=eth0\0" \
- "tftpflash=tftpboot $loadaddr $uboot && " \
- "protect off $ubootaddr +$filesize && " \
- "erase $ubootaddr +$filesize && " \
- "cp.b $loadaddr $ubootaddr $filesize && " \
- "protect on $ubootaddr +$filesize && " \
- "cmp.b $loadaddr $ubootaddr $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "fdtaddr=1e00000\0" \
- "bdev=sda3\0"
-
-#define CONFIG_LINUX \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-
-#include <asm/fsl_secure_boot.h>
-
-#endif /* __T1024RDB_H */
This board has not been converted to CONFIG_DM_SPI by the deadline. Remove it. Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- arch/powerpc/cpu/mpc85xx/Kconfig | 1 - board/freescale/t102xrdb/Kconfig | 14 - board/freescale/t102xrdb/MAINTAINERS | 15 - board/freescale/t102xrdb/Makefile | 17 - board/freescale/t102xrdb/README | 340 --------- board/freescale/t102xrdb/cpld.c | 102 --- board/freescale/t102xrdb/cpld.h | 48 -- board/freescale/t102xrdb/ddr.c | 257 ------- board/freescale/t102xrdb/eth_t102xrdb.c | 146 ---- board/freescale/t102xrdb/law.c | 31 - board/freescale/t102xrdb/pci.c | 25 - board/freescale/t102xrdb/spl.c | 143 ---- board/freescale/t102xrdb/t1023_nand_rcw.cfg | 8 - board/freescale/t102xrdb/t1023_sd_rcw.cfg | 8 - board/freescale/t102xrdb/t1023_spi_rcw.cfg | 8 - board/freescale/t102xrdb/t1024_nand_rcw.cfg | 8 - board/freescale/t102xrdb/t1024_pbi.cfg | 26 - board/freescale/t102xrdb/t1024_sd_rcw.cfg | 8 - board/freescale/t102xrdb/t1024_spi_rcw.cfg | 8 - board/freescale/t102xrdb/t102xrdb.c | 394 ----------- board/freescale/t102xrdb/t102xrdb.h | 15 - board/freescale/t102xrdb/tlb.c | 116 ---- configs/T1023RDB_NAND_defconfig | 77 --- configs/T1023RDB_SDCARD_defconfig | 74 -- configs/T1023RDB_SECURE_BOOT_defconfig | 64 -- configs/T1023RDB_SPIFLASH_defconfig | 77 --- configs/T1023RDB_defconfig | 61 -- configs/T1024RDB_NAND_defconfig | 86 --- configs/T1024RDB_SDCARD_defconfig | 83 --- configs/T1024RDB_SECURE_BOOT_defconfig | 66 -- configs/T1024RDB_SPIFLASH_defconfig | 86 --- configs/T1024RDB_defconfig | 71 -- include/configs/T102xRDB.h | 721 -------------------- 33 files changed, 3204 deletions(-) delete mode 100644 board/freescale/t102xrdb/Kconfig delete mode 100644 board/freescale/t102xrdb/MAINTAINERS delete mode 100644 board/freescale/t102xrdb/Makefile delete mode 100644 board/freescale/t102xrdb/README delete mode 100644 board/freescale/t102xrdb/cpld.c delete mode 100644 board/freescale/t102xrdb/cpld.h delete mode 100644 board/freescale/t102xrdb/ddr.c delete mode 100644 board/freescale/t102xrdb/eth_t102xrdb.c delete mode 100644 board/freescale/t102xrdb/law.c delete mode 100644 board/freescale/t102xrdb/pci.c delete mode 100644 board/freescale/t102xrdb/spl.c delete mode 100644 board/freescale/t102xrdb/t1023_nand_rcw.cfg delete mode 100644 board/freescale/t102xrdb/t1023_sd_rcw.cfg delete mode 100644 board/freescale/t102xrdb/t1023_spi_rcw.cfg delete mode 100644 board/freescale/t102xrdb/t1024_nand_rcw.cfg delete mode 100644 board/freescale/t102xrdb/t1024_pbi.cfg delete mode 100644 board/freescale/t102xrdb/t1024_sd_rcw.cfg delete mode 100644 board/freescale/t102xrdb/t1024_spi_rcw.cfg delete mode 100644 board/freescale/t102xrdb/t102xrdb.c delete mode 100644 board/freescale/t102xrdb/t102xrdb.h delete mode 100644 board/freescale/t102xrdb/tlb.c delete mode 100644 configs/T1023RDB_NAND_defconfig delete mode 100644 configs/T1023RDB_SDCARD_defconfig delete mode 100644 configs/T1023RDB_SECURE_BOOT_defconfig delete mode 100644 configs/T1023RDB_SPIFLASH_defconfig delete mode 100644 configs/T1023RDB_defconfig delete mode 100644 configs/T1024RDB_NAND_defconfig delete mode 100644 configs/T1024RDB_SDCARD_defconfig delete mode 100644 configs/T1024RDB_SECURE_BOOT_defconfig delete mode 100644 configs/T1024RDB_SPIFLASH_defconfig delete mode 100644 configs/T1024RDB_defconfig delete mode 100644 include/configs/T102xRDB.h