diff mbox series

[v2,19/21] mips: mtmips: add SPL support

Message ID 1579247169-525-1-git-send-email-weijie.gao@mediatek.com
State New
Headers show
Series None | expand

Commit Message

Weijie Gao Jan. 17, 2020, 7:46 a.m. UTC
This patch adds SPL support for mtmips platform. The lowlevel architecture
is split into SPL and the rest parts are built into a memory loadable
u-boot image. Optional SPL_DM and OF_CONTROL are also supported.

The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
not enabled and the memory bootable u-boot (u-boot.img) is generated
automatically so there is not need to add a separate config for it.

A lzma compressed payload (u-boot-lzma.img) is also generated and it will
be combined with u-boot-spl.bin to form the unified ROM bootable binary
u-boot-mtmips.bin.

A spl loader is added to support uncompress the payload.

Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
---
Changes since v1:
  move spl loader into this patch.
  add full pinmux for all three uarts.
  add optional DM & DT support.
---
 Makefile                                    |   9 ++
 arch/mips/Kconfig                           |   3 +
 arch/mips/dts/mt7628-u-boot.dtsi            |  24 ++++
 arch/mips/mach-mtmips/Kconfig               |  24 ++++
 arch/mips/mach-mtmips/Makefile              |   1 +
 arch/mips/mach-mtmips/include/mach/serial.h |  13 +++
 arch/mips/mach-mtmips/include/mach/spl.h    |  14 +++
 arch/mips/mach-mtmips/mt7628/Makefile       |   1 +
 arch/mips/mach-mtmips/mt7628/serial.c       |  34 ++++++
 arch/mips/mach-mtmips/spl.c                 |  31 +++++
 arch/mips/mach-mtmips/spl_load.c            | 121 ++++++++++++++++++++
 11 files changed, 275 insertions(+)
 create mode 100644 arch/mips/dts/mt7628-u-boot.dtsi
 create mode 100644 arch/mips/mach-mtmips/include/mach/serial.h
 create mode 100644 arch/mips/mach-mtmips/include/mach/spl.h
 create mode 100644 arch/mips/mach-mtmips/mt7628/serial.c
 create mode 100644 arch/mips/mach-mtmips/spl.c
 create mode 100644 arch/mips/mach-mtmips/spl_load.c

Comments

Daniel Schwierzeck Jan. 17, 2020, 1:15 p.m. UTC | #1
Am 17.01.20 um 08:46 schrieb Weijie Gao:
> This patch adds SPL support for mtmips platform. The lowlevel architecture
> is split into SPL and the rest parts are built into a memory loadable
> u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
> 
> The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
> not enabled and the memory bootable u-boot (u-boot.img) is generated
> automatically so there is not need to add a separate config for it.
> 
> A lzma compressed payload (u-boot-lzma.img) is also generated and it will
> be combined with u-boot-spl.bin to form the unified ROM bootable binary
> u-boot-mtmips.bin.
> 
> A spl loader is added to support uncompress the payload.
> 
> Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
> ---
> Changes since v1:
>   move spl loader into this patch.
>   add full pinmux for all three uarts.
>   add optional DM & DT support.
> ---
>  Makefile                                    |   9 ++
>  arch/mips/Kconfig                           |   3 +
>  arch/mips/dts/mt7628-u-boot.dtsi            |  24 ++++
>  arch/mips/mach-mtmips/Kconfig               |  24 ++++
>  arch/mips/mach-mtmips/Makefile              |   1 +
>  arch/mips/mach-mtmips/include/mach/serial.h |  13 +++
>  arch/mips/mach-mtmips/include/mach/spl.h    |  14 +++
>  arch/mips/mach-mtmips/mt7628/Makefile       |   1 +
>  arch/mips/mach-mtmips/mt7628/serial.c       |  34 ++++++
>  arch/mips/mach-mtmips/spl.c                 |  31 +++++
>  arch/mips/mach-mtmips/spl_load.c            | 121 ++++++++++++++++++++
>  11 files changed, 275 insertions(+)
>  create mode 100644 arch/mips/dts/mt7628-u-boot.dtsi
>  create mode 100644 arch/mips/mach-mtmips/include/mach/serial.h
>  create mode 100644 arch/mips/mach-mtmips/include/mach/spl.h
>  create mode 100644 arch/mips/mach-mtmips/mt7628/serial.c
>  create mode 100644 arch/mips/mach-mtmips/spl.c
>  create mode 100644 arch/mips/mach-mtmips/spl_load.c
> 
> diff --git a/Makefile b/Makefile
> index 8013cbd9f9..1e18a37913 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -895,6 +895,7 @@ ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb-tegra.bin
>  endif
>  
>  ALL-$(CONFIG_ARCH_MEDIATEK) += u-boot-mtk.bin
> +ALL-$(CONFIG_ARCH_MTMIPS) += u-boot-mtmips.bin
>  
>  # Add optional build target if defined in board/cpu/soc headers
>  ifneq ($(CONFIG_BUILD_TARGET),)
> @@ -1664,6 +1665,14 @@ u-boot-mtk.bin: u-boot.bin FORCE
>  	$(call if_changed,mkimage)
>  endif
>  
> +ifeq ($(CONFIG_SPL),y)
> +u-boot-mtmips.bin: u-boot.dtb u-boot-lzma.img spl/u-boot-spl.bin FORCE
> +	$(call if_changed,binman)
> +else
> +u-boot-mtmips.bin: u-boot.bin FORCE
> +	$(call if_changed,copy)
> +endif
> +
>  ARCH_POSTLINK := $(wildcard $(srctree)/arch/$(ARCH)/Makefile.postlink)
>  
>  # Rule to link u-boot
> diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
> index 5f82caf8be..5f74f549b5 100644
> --- a/arch/mips/Kconfig
> +++ b/arch/mips/Kconfig
> @@ -98,6 +98,9 @@ config ARCH_MTMIPS
>  	select SUPPORTS_CPU_MIPS32_R2
>  	select SUPPORTS_LITTLE_ENDIAN
>  	select SYSRESET
> +	select SUPPORT_SPL
> +	select SPL_LZMA
> +	select BINMAN
>  
>  config ARCH_JZ47XX
>  	bool "Support Ingenic JZ47xx"
> diff --git a/arch/mips/dts/mt7628-u-boot.dtsi b/arch/mips/dts/mt7628-u-boot.dtsi
> new file mode 100644
> index 0000000000..213959105f
> --- /dev/null
> +++ b/arch/mips/dts/mt7628-u-boot.dtsi
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +/ {
> +	binman {
> +		filename = "u-boot-mtmips.bin";
> +		pad-byte = <0xff>;
> +
> +#ifdef CONFIG_SPL
> +		u-boot-spl {
> +		};
> +
> +		u-boot-lzma-img {
> +		};
> +#else
> +		u-boot {
> +		};
> +#endif
> +	};
> +};
> diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig
> index 3f25de8b85..9b42d5b581 100644
> --- a/arch/mips/mach-mtmips/Kconfig
> +++ b/arch/mips/mach-mtmips/Kconfig
> @@ -20,8 +20,16 @@ config SYS_ICACHE_LINE_SIZE
>  	default 32
>  
>  config SYS_TEXT_BASE
> +	default 0x9c000000 if !SPL
> +	default 0x80200000 if SPL
> +
> +config SPL_TEXT_BASE
>  	default 0x9c000000
>  
> +config SPL_LOADER_SUPPORT
> +	bool
> +	default y
> +

this option should be moved to arch/mips/Kconfig and should be added
with patch 15/21 because you use reference that option in the generic
MIPS u-boot-spl.lds

>  choice
>  	prompt "MediaTek MIPS SoC select"
>  
> @@ -34,6 +42,14 @@ config SOC_MT7628
>  	select PINCTRL_MT7628
>  	select MTK_SERIAL
>  	select SYSRESET_RESETCTL
> +	select SPL_SEPARATE_BSS if SPL
> +	select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL
> +	select SPL_OF_CONTROL if SPL_DM
> +	select SPL_SIMPLE_BUS if SPL_DM
> +	select SPL_DM_SERIAL if SPL_DM
> +	select SPL_CLK if SPL_DM && SPL_SERIAL_SUPPORT
> +	select SPL_SYSRESET if SPL_DM
> +	select SPL_OF_LIBFDT if SPL_OF_CONTROL
>  	help
>  	  This supports MediaTek MT7628/MT7688.
>  
> @@ -88,6 +104,14 @@ endchoice
>  config SUPPORTS_BOOT_RAM
>  	bool
>  
> +config SPL_UART2_SPIS_PINMUX
> +	bool "Use alternative pinmux for UART2 in SPL stage"
> +	depends on SPL_SERIAL_SUPPORT
> +	default n
> +	help
> +	  Select this if the UART2 of your board is connected to GPIO 16/17
> +	  (shared with SPIS) rather than the usual GPIO 20/21.
> +
>  source "board/gardena/smart-gateway-mt7688/Kconfig"
>  source "board/seeed/linkit-smart-7688/Kconfig"
>  
> diff --git a/arch/mips/mach-mtmips/Makefile b/arch/mips/mach-mtmips/Makefile
> index 72f0369030..08d2a236d0 100644
> --- a/arch/mips/mach-mtmips/Makefile
> +++ b/arch/mips/mach-mtmips/Makefile
> @@ -3,5 +3,6 @@
>  obj-y += cpu.o
>  obj-y += ddr_init.o
>  obj-y += ddr_cal.o
> +obj-$(CONFIG_SPL_BUILD) += spl.o spl_load.o
>  
>  obj-$(CONFIG_SOC_MT7628) += mt7628/
> diff --git a/arch/mips/mach-mtmips/include/mach/serial.h b/arch/mips/mach-mtmips/include/mach/serial.h
> new file mode 100644
> index 0000000000..bfa246b428
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/include/mach/serial.h
> @@ -0,0 +1,13 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + *
> + * Author:  Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#ifndef _MTMIPS_SERIAL_H_
> +#define _MTMIPS_SERIAL_H_
> +
> +void mtmips_spl_serial_init(void);
> +
> +#endif /* _MTMIPS_SERIAL_H_ */
> diff --git a/arch/mips/mach-mtmips/include/mach/spl.h b/arch/mips/mach-mtmips/include/mach/spl.h
> new file mode 100644
> index 0000000000..5674dd533e
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/include/mach/spl.h
> @@ -0,0 +1,14 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +#ifndef	_MACH_MTMIPS_SPL_H_
> +#define	_MACH_MTMIPS_SPL_H_
> +
> +#include <asm/spl.h>
> +
> +#define BOOT_DEVICE_MTMIPS_NOR	(BOOT_DEVICE_BOOTROM + 0x100)
> +
> +#endif /* _MACH_MTMIPS_SPL_H_ */
> diff --git a/arch/mips/mach-mtmips/mt7628/Makefile b/arch/mips/mach-mtmips/mt7628/Makefile
> index db62e90d77..7e139d5adf 100644
> --- a/arch/mips/mach-mtmips/mt7628/Makefile
> +++ b/arch/mips/mach-mtmips/mt7628/Makefile
> @@ -3,3 +3,4 @@
>  obj-y += lowlevel_init.o
>  obj-y += init.o
>  obj-y += ddr.o
> +obj-$(CONFIG_SPL_BUILD) += serial.o
> diff --git a/arch/mips/mach-mtmips/mt7628/serial.c b/arch/mips/mach-mtmips/mt7628/serial.c
> new file mode 100644
> index 0000000000..a7d324792d
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/mt7628/serial.c
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + *
> + * Author:  Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include "mt7628.h"
> +
> +void mtmips_spl_serial_init(void)
> +{
> +#ifdef CONFIG_SPL_SERIAL_SUPPORT
> +	void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
> +
> +#if CONFIG_CONS_INDEX == 1
> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART0_MODE_M);
> +#elif CONFIG_CONS_INDEX == 2
> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART1_MODE_M);
> +#elif CONFIG_CONS_INDEX == 3
> +	setbits_32(base + SYSCTL_AGPIO_CFG_REG, EPHY_GPIO_AIO_EN_M);
> +#ifdef CONFIG_SPL_UART2_SPIS_PINMUX
> +	setbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M);
> +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M,
> +		      1 << UART2_MODE_S);
> +#else
> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M);
> +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M,
> +		      1 << SPIS_MODE_S);
> +#endif /* CONFIG_SPL_UART2_SPIS_PINMUX */
> +#endif /* CONFIG_CONS_INDEX */
> +#endif /* CONFIG_SPL_SERIAL_SUPPORT */
> +}
> diff --git a/arch/mips/mach-mtmips/spl.c b/arch/mips/mach-mtmips/spl.c
> new file mode 100644
> index 0000000000..f12fb70d75
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/spl.c
> @@ -0,0 +1,31 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +#include <linux/sizes.h>
> +#include <mach/serial.h>
> +#include <mach/spl.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +void __noreturn board_init_f(ulong dummy)
> +{
> +	spl_init();
> +
> +#ifdef CONFIG_SPL_SERIAL_SUPPORT
> +	mtmips_spl_serial_init();
> +	preloader_console_init();
> +#endif
> +
> +	board_init_r(NULL, 0);
> +}
> +
> +void board_boot_order(u32 *spl_boot_list)
> +{
> +	spl_boot_list[0] = BOOT_DEVICE_MTMIPS_NOR;
> +}
> diff --git a/arch/mips/mach-mtmips/spl_load.c b/arch/mips/mach-mtmips/spl_load.c
> new file mode 100644
> index 0000000000..95dd491baa
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/spl_load.c
> @@ -0,0 +1,121 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#include <common.h>
> +#include <cpu_func.h>
> +#include <asm/sections.h>
> +#include <linux/compiler.h>
> +#include <linux/sizes.h>
> +#include <mach/spl.h>
> +#include <spl.h>
> +
> +#ifdef CONFIG_SPL_LZMA
> +#include <lzma/LzmaTypes.h>
> +#include <lzma/LzmaDec.h>
> +#include <lzma/LzmaTools.h>
> +#endif /* CONFIG_SPL_LZMA */
> +
> +#if CONFIG_IS_ENABLED(OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
> +#include <fdt.h>
> +#endif
> +
> +static ulong spl_dtb_size(void)
> +{
> +#if CONFIG_IS_ENABLED(OF_CONTROL)
> +	void *fdt = __image_copy_end;
> +
> +	if (fdt_magic(fdt) == FDT_MAGIC)
> +		return fdt_totalsize(fdt);
> +#endif
> +
> +	return 0;
> +}
> +
> +static int spl_try_load_image(struct spl_image_info *spl_image,
> +			      void *image_addr)
> +{
> +	int ret;
> +	uintptr_t dataptr;
> +	struct image_header hdr;
> +	size_t __maybe_unused lzma_len;
> +
> +	memcpy(&hdr, (const void *)image_addr, sizeof(hdr));
> +
> +	ret = spl_parse_image_header(spl_image, &hdr);
> +	if (ret)
> +		return ret;
> +
> +	if (!spl_image->entry_point)
> +		spl_image->entry_point = spl_image->load_addr;
> +
> +	dataptr = (uintptr_t)image_addr + sizeof(hdr);
> +
> +	switch (hdr.ih_comp) {
> +	case IH_COMP_NONE:
> +		/*
> +		 * Load real U-Boot from its location to its defined location
> +		 * in SDRAM
> +		 */
> +		if (spl_image->load_addr != dataptr) {
> +			memmove((void *)spl_image->load_addr, (void *)dataptr,
> +				spl_image->size);
> +		}
> +		break;
> +#ifdef CONFIG_SPL_LZMA
> +	case IH_COMP_LZMA:
> +		/*
> +		 * Uncompress real U-Boot to its defined location in SDRAM
> +		 */
> +		lzma_len = SZ_8M;
> +
> +		ret = lzmaBuffToBuffDecompress((u8 *)spl_image->load_addr,
> +					       &lzma_len, (u8 *)dataptr,
> +					       spl_image->size);
> +
> +		if (ret) {
> +			printf("Error: LZMA uncompression error: %d\n", ret);
> +			return ret;
> +		}
> +
> +		spl_image->size = lzma_len;
> +		break;
> +#endif /* CONFIG_SPL_LZMA */
> +	default:
> +		debug("Warning: Unsupported compression method found in image "
> +		      "header at offset 0x%p\n", image_addr);
> +		return -EINVAL;
> +	}
> +
> +	flush_cache((unsigned long)spl_image->load_addr, spl_image->size);
> +
> +	return 0;
> +}
> +
> +static int spl_mtk_nor_load_image(struct spl_image_info *spl_image,
> +				  struct spl_boot_device *bootdev)
> +{
> +	ulong offset = spl_dtb_size();
> +
> +	/*
> +	 * Loading of the payload to SDRAM is done with skipping of
> +	 * the mkimage header
> +	 */
> +	spl_image->flags |= SPL_COPY_PAYLOAD_ONLY;
> +
> +	/* Try to boot without padding */
> +	if (!spl_try_load_image(spl_image, (u8 *)__image_copy_end + offset))
> +		return 0;
> +
> +#ifdef CONFIG_SYS_UBOOT_BASE
> +	/* Try user defined offset */
> +	if (!spl_try_load_image(spl_image, (void *)CONFIG_SYS_UBOOT_BASE))
> +		return 0;
> +#endif
> +
> +	return -EINVAL;
> +}
> +SPL_LOAD_IMAGE_METHOD("NOR", 0, BOOT_DEVICE_MTMIPS_NOR, spl_mtk_nor_load_image);
> 

maybe in a future patch series this could be refactored to a generic SPL
decompressor in common/spl/ with spl_nor.c as the first user. Then it
could be used by other archs or other SPL boot methods like SPI or NAND.
Stefan Roese Jan. 17, 2020, 2:55 p.m. UTC | #2
Added Mauro to Cc

On 17.01.20 08:46, Weijie Gao wrote:
> This patch adds SPL support for mtmips platform. The lowlevel architecture
> is split into SPL and the rest parts are built into a memory loadable
> u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
> 
> The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
> not enabled and the memory bootable u-boot (u-boot.img) is generated
> automatically so there is not need to add a separate config for it.
> 
> A lzma compressed payload (u-boot-lzma.img) is also generated and it will
> be combined with u-boot-spl.bin to form the unified ROM bootable binary
> u-boot-mtmips.bin.
> 
> A spl loader is added to support uncompress the payload.
> 
> Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
> ---
> Changes since v1:
>    move spl loader into this patch.
>    add full pinmux for all three uarts.
>    add optional DM & DT support.
> ---
>   Makefile                                    |   9 ++
>   arch/mips/Kconfig                           |   3 +
>   arch/mips/dts/mt7628-u-boot.dtsi            |  24 ++++
>   arch/mips/mach-mtmips/Kconfig               |  24 ++++
>   arch/mips/mach-mtmips/Makefile              |   1 +
>   arch/mips/mach-mtmips/include/mach/serial.h |  13 +++
>   arch/mips/mach-mtmips/include/mach/spl.h    |  14 +++
>   arch/mips/mach-mtmips/mt7628/Makefile       |   1 +
>   arch/mips/mach-mtmips/mt7628/serial.c       |  34 ++++++
>   arch/mips/mach-mtmips/spl.c                 |  31 +++++
>   arch/mips/mach-mtmips/spl_load.c            | 121 ++++++++++++++++++++
>   11 files changed, 275 insertions(+)
>   create mode 100644 arch/mips/dts/mt7628-u-boot.dtsi
>   create mode 100644 arch/mips/mach-mtmips/include/mach/serial.h
>   create mode 100644 arch/mips/mach-mtmips/include/mach/spl.h
>   create mode 100644 arch/mips/mach-mtmips/mt7628/serial.c
>   create mode 100644 arch/mips/mach-mtmips/spl.c
>   create mode 100644 arch/mips/mach-mtmips/spl_load.c
> 
> diff --git a/Makefile b/Makefile
> index 8013cbd9f9..1e18a37913 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -895,6 +895,7 @@ ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb-tegra.bin
>   endif
>   
>   ALL-$(CONFIG_ARCH_MEDIATEK) += u-boot-mtk.bin
> +ALL-$(CONFIG_ARCH_MTMIPS) += u-boot-mtmips.bin
>   
>   # Add optional build target if defined in board/cpu/soc headers
>   ifneq ($(CONFIG_BUILD_TARGET),)
> @@ -1664,6 +1665,14 @@ u-boot-mtk.bin: u-boot.bin FORCE
>   	$(call if_changed,mkimage)
>   endif
>   
> +ifeq ($(CONFIG_SPL),y)
> +u-boot-mtmips.bin: u-boot.dtb u-boot-lzma.img spl/u-boot-spl.bin FORCE
> +	$(call if_changed,binman)
> +else
> +u-boot-mtmips.bin: u-boot.bin FORCE
> +	$(call if_changed,copy)
> +endif
> +
>   ARCH_POSTLINK := $(wildcard $(srctree)/arch/$(ARCH)/Makefile.postlink)
>   
>   # Rule to link u-boot
> diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
> index 5f82caf8be..5f74f549b5 100644
> --- a/arch/mips/Kconfig
> +++ b/arch/mips/Kconfig
> @@ -98,6 +98,9 @@ config ARCH_MTMIPS
>   	select SUPPORTS_CPU_MIPS32_R2
>   	select SUPPORTS_LITTLE_ENDIAN
>   	select SYSRESET
> +	select SUPPORT_SPL
> +	select SPL_LZMA
> +	select BINMAN
>   
>   config ARCH_JZ47XX
>   	bool "Support Ingenic JZ47xx"
> diff --git a/arch/mips/dts/mt7628-u-boot.dtsi b/arch/mips/dts/mt7628-u-boot.dtsi
> new file mode 100644
> index 0000000000..213959105f
> --- /dev/null
> +++ b/arch/mips/dts/mt7628-u-boot.dtsi
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +/ {
> +	binman {
> +		filename = "u-boot-mtmips.bin";
> +		pad-byte = <0xff>;
> +
> +#ifdef CONFIG_SPL
> +		u-boot-spl {
> +		};
> +
> +		u-boot-lzma-img {
> +		};
> +#else
> +		u-boot {
> +		};
> +#endif
> +	};
> +};
> diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig
> index 3f25de8b85..9b42d5b581 100644
> --- a/arch/mips/mach-mtmips/Kconfig
> +++ b/arch/mips/mach-mtmips/Kconfig
> @@ -20,8 +20,16 @@ config SYS_ICACHE_LINE_SIZE
>   	default 32
>   
>   config SYS_TEXT_BASE
> +	default 0x9c000000 if !SPL
> +	default 0x80200000 if SPL
> +
> +config SPL_TEXT_BASE
>   	default 0x9c000000
>   
> +config SPL_LOADER_SUPPORT
> +	bool
> +	default y
> +
>   choice
>   	prompt "MediaTek MIPS SoC select"
>   
> @@ -34,6 +42,14 @@ config SOC_MT7628
>   	select PINCTRL_MT7628
>   	select MTK_SERIAL
>   	select SYSRESET_RESETCTL
> +	select SPL_SEPARATE_BSS if SPL
> +	select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL
> +	select SPL_OF_CONTROL if SPL_DM
> +	select SPL_SIMPLE_BUS if SPL_DM
> +	select SPL_DM_SERIAL if SPL_DM
> +	select SPL_CLK if SPL_DM && SPL_SERIAL_SUPPORT
> +	select SPL_SYSRESET if SPL_DM
> +	select SPL_OF_LIBFDT if SPL_OF_CONTROL
>   	help
>   	  This supports MediaTek MT7628/MT7688.
>   
> @@ -88,6 +104,14 @@ endchoice
>   config SUPPORTS_BOOT_RAM
>   	bool
>   
> +config SPL_UART2_SPIS_PINMUX
> +	bool "Use alternative pinmux for UART2 in SPL stage"
> +	depends on SPL_SERIAL_SUPPORT
> +	default n
> +	help
> +	  Select this if the UART2 of your board is connected to GPIO 16/17
> +	  (shared with SPIS) rather than the usual GPIO 20/21.
> +

Again, do you know if this is the option that needs to be selected
for the VoCore2 board?

Thanks,
Stefan

>   source "board/gardena/smart-gateway-mt7688/Kconfig"
>   source "board/seeed/linkit-smart-7688/Kconfig"
>   
> diff --git a/arch/mips/mach-mtmips/Makefile b/arch/mips/mach-mtmips/Makefile
> index 72f0369030..08d2a236d0 100644
> --- a/arch/mips/mach-mtmips/Makefile
> +++ b/arch/mips/mach-mtmips/Makefile
> @@ -3,5 +3,6 @@
>   obj-y += cpu.o
>   obj-y += ddr_init.o
>   obj-y += ddr_cal.o
> +obj-$(CONFIG_SPL_BUILD) += spl.o spl_load.o
>   
>   obj-$(CONFIG_SOC_MT7628) += mt7628/
> diff --git a/arch/mips/mach-mtmips/include/mach/serial.h b/arch/mips/mach-mtmips/include/mach/serial.h
> new file mode 100644
> index 0000000000..bfa246b428
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/include/mach/serial.h
> @@ -0,0 +1,13 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + *
> + * Author:  Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#ifndef _MTMIPS_SERIAL_H_
> +#define _MTMIPS_SERIAL_H_
> +
> +void mtmips_spl_serial_init(void);
> +
> +#endif /* _MTMIPS_SERIAL_H_ */
> diff --git a/arch/mips/mach-mtmips/include/mach/spl.h b/arch/mips/mach-mtmips/include/mach/spl.h
> new file mode 100644
> index 0000000000..5674dd533e
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/include/mach/spl.h
> @@ -0,0 +1,14 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +#ifndef	_MACH_MTMIPS_SPL_H_
> +#define	_MACH_MTMIPS_SPL_H_
> +
> +#include <asm/spl.h>
> +
> +#define BOOT_DEVICE_MTMIPS_NOR	(BOOT_DEVICE_BOOTROM + 0x100)
> +
> +#endif /* _MACH_MTMIPS_SPL_H_ */
> diff --git a/arch/mips/mach-mtmips/mt7628/Makefile b/arch/mips/mach-mtmips/mt7628/Makefile
> index db62e90d77..7e139d5adf 100644
> --- a/arch/mips/mach-mtmips/mt7628/Makefile
> +++ b/arch/mips/mach-mtmips/mt7628/Makefile
> @@ -3,3 +3,4 @@
>   obj-y += lowlevel_init.o
>   obj-y += init.o
>   obj-y += ddr.o
> +obj-$(CONFIG_SPL_BUILD) += serial.o
> diff --git a/arch/mips/mach-mtmips/mt7628/serial.c b/arch/mips/mach-mtmips/mt7628/serial.c
> new file mode 100644
> index 0000000000..a7d324792d
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/mt7628/serial.c
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + *
> + * Author:  Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include "mt7628.h"
> +
> +void mtmips_spl_serial_init(void)
> +{
> +#ifdef CONFIG_SPL_SERIAL_SUPPORT
> +	void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
> +
> +#if CONFIG_CONS_INDEX == 1
> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART0_MODE_M);
> +#elif CONFIG_CONS_INDEX == 2
> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART1_MODE_M);
> +#elif CONFIG_CONS_INDEX == 3
> +	setbits_32(base + SYSCTL_AGPIO_CFG_REG, EPHY_GPIO_AIO_EN_M);
> +#ifdef CONFIG_SPL_UART2_SPIS_PINMUX
> +	setbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M);
> +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M,
> +		      1 << UART2_MODE_S);
> +#else
> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M);
> +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M,
> +		      1 << SPIS_MODE_S);
> +#endif /* CONFIG_SPL_UART2_SPIS_PINMUX */
> +#endif /* CONFIG_CONS_INDEX */
> +#endif /* CONFIG_SPL_SERIAL_SUPPORT */
> +}
> diff --git a/arch/mips/mach-mtmips/spl.c b/arch/mips/mach-mtmips/spl.c
> new file mode 100644
> index 0000000000..f12fb70d75
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/spl.c
> @@ -0,0 +1,31 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +#include <linux/sizes.h>
> +#include <mach/serial.h>
> +#include <mach/spl.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +void __noreturn board_init_f(ulong dummy)
> +{
> +	spl_init();
> +
> +#ifdef CONFIG_SPL_SERIAL_SUPPORT
> +	mtmips_spl_serial_init();
> +	preloader_console_init();
> +#endif
> +
> +	board_init_r(NULL, 0);
> +}
> +
> +void board_boot_order(u32 *spl_boot_list)
> +{
> +	spl_boot_list[0] = BOOT_DEVICE_MTMIPS_NOR;
> +}
> diff --git a/arch/mips/mach-mtmips/spl_load.c b/arch/mips/mach-mtmips/spl_load.c
> new file mode 100644
> index 0000000000..95dd491baa
> --- /dev/null
> +++ b/arch/mips/mach-mtmips/spl_load.c
> @@ -0,0 +1,121 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> + *
> + * Author: Weijie Gao <weijie.gao at mediatek.com>
> + */
> +
> +#include <common.h>
> +#include <cpu_func.h>
> +#include <asm/sections.h>
> +#include <linux/compiler.h>
> +#include <linux/sizes.h>
> +#include <mach/spl.h>
> +#include <spl.h>
> +
> +#ifdef CONFIG_SPL_LZMA
> +#include <lzma/LzmaTypes.h>
> +#include <lzma/LzmaDec.h>
> +#include <lzma/LzmaTools.h>
> +#endif /* CONFIG_SPL_LZMA */
> +
> +#if CONFIG_IS_ENABLED(OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
> +#include <fdt.h>
> +#endif
> +
> +static ulong spl_dtb_size(void)
> +{
> +#if CONFIG_IS_ENABLED(OF_CONTROL)
> +	void *fdt = __image_copy_end;
> +
> +	if (fdt_magic(fdt) == FDT_MAGIC)
> +		return fdt_totalsize(fdt);
> +#endif
> +
> +	return 0;
> +}
> +
> +static int spl_try_load_image(struct spl_image_info *spl_image,
> +			      void *image_addr)
> +{
> +	int ret;
> +	uintptr_t dataptr;
> +	struct image_header hdr;
> +	size_t __maybe_unused lzma_len;
> +
> +	memcpy(&hdr, (const void *)image_addr, sizeof(hdr));
> +
> +	ret = spl_parse_image_header(spl_image, &hdr);
> +	if (ret)
> +		return ret;
> +
> +	if (!spl_image->entry_point)
> +		spl_image->entry_point = spl_image->load_addr;
> +
> +	dataptr = (uintptr_t)image_addr + sizeof(hdr);
> +
> +	switch (hdr.ih_comp) {
> +	case IH_COMP_NONE:
> +		/*
> +		 * Load real U-Boot from its location to its defined location
> +		 * in SDRAM
> +		 */
> +		if (spl_image->load_addr != dataptr) {
> +			memmove((void *)spl_image->load_addr, (void *)dataptr,
> +				spl_image->size);
> +		}
> +		break;
> +#ifdef CONFIG_SPL_LZMA
> +	case IH_COMP_LZMA:
> +		/*
> +		 * Uncompress real U-Boot to its defined location in SDRAM
> +		 */
> +		lzma_len = SZ_8M;
> +
> +		ret = lzmaBuffToBuffDecompress((u8 *)spl_image->load_addr,
> +					       &lzma_len, (u8 *)dataptr,
> +					       spl_image->size);
> +
> +		if (ret) {
> +			printf("Error: LZMA uncompression error: %d\n", ret);
> +			return ret;
> +		}
> +
> +		spl_image->size = lzma_len;
> +		break;
> +#endif /* CONFIG_SPL_LZMA */
> +	default:
> +		debug("Warning: Unsupported compression method found in image "
> +		      "header at offset 0x%p\n", image_addr);
> +		return -EINVAL;
> +	}
> +
> +	flush_cache((unsigned long)spl_image->load_addr, spl_image->size);
> +
> +	return 0;
> +}
> +
> +static int spl_mtk_nor_load_image(struct spl_image_info *spl_image,
> +				  struct spl_boot_device *bootdev)
> +{
> +	ulong offset = spl_dtb_size();
> +
> +	/*
> +	 * Loading of the payload to SDRAM is done with skipping of
> +	 * the mkimage header
> +	 */
> +	spl_image->flags |= SPL_COPY_PAYLOAD_ONLY;
> +
> +	/* Try to boot without padding */
> +	if (!spl_try_load_image(spl_image, (u8 *)__image_copy_end + offset))
> +		return 0;
> +
> +#ifdef CONFIG_SYS_UBOOT_BASE
> +	/* Try user defined offset */
> +	if (!spl_try_load_image(spl_image, (void *)CONFIG_SYS_UBOOT_BASE))
> +		return 0;
> +#endif
> +
> +	return -EINVAL;
> +}
> +SPL_LOAD_IMAGE_METHOD("NOR", 0, BOOT_DEVICE_MTMIPS_NOR, spl_mtk_nor_load_image);
> 

Viele Grüße,
Stefan
Stefan Roese Jan. 17, 2020, 2:58 p.m. UTC | #3
On 17.01.20 14:15, Daniel Schwierzeck wrote:
> 
> 
> Am 17.01.20 um 08:46 schrieb Weijie Gao:
>> This patch adds SPL support for mtmips platform. The lowlevel architecture
>> is split into SPL and the rest parts are built into a memory loadable
>> u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
>>
>> The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
>> not enabled and the memory bootable u-boot (u-boot.img) is generated
>> automatically so there is not need to add a separate config for it.
>>
>> A lzma compressed payload (u-boot-lzma.img) is also generated and it will
>> be combined with u-boot-spl.bin to form the unified ROM bootable binary
>> u-boot-mtmips.bin.
>>
>> A spl loader is added to support uncompress the payload.
>>
>> Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
>> ---
>> Changes since v1:
>>    move spl loader into this patch.
>>    add full pinmux for all three uarts.
>>    add optional DM & DT support.
>> ---
>>   Makefile                                    |   9 ++
>>   arch/mips/Kconfig                           |   3 +
>>   arch/mips/dts/mt7628-u-boot.dtsi            |  24 ++++
>>   arch/mips/mach-mtmips/Kconfig               |  24 ++++
>>   arch/mips/mach-mtmips/Makefile              |   1 +
>>   arch/mips/mach-mtmips/include/mach/serial.h |  13 +++
>>   arch/mips/mach-mtmips/include/mach/spl.h    |  14 +++
>>   arch/mips/mach-mtmips/mt7628/Makefile       |   1 +
>>   arch/mips/mach-mtmips/mt7628/serial.c       |  34 ++++++
>>   arch/mips/mach-mtmips/spl.c                 |  31 +++++
>>   arch/mips/mach-mtmips/spl_load.c            | 121 ++++++++++++++++++++
>>   11 files changed, 275 insertions(+)
>>   create mode 100644 arch/mips/dts/mt7628-u-boot.dtsi
>>   create mode 100644 arch/mips/mach-mtmips/include/mach/serial.h
>>   create mode 100644 arch/mips/mach-mtmips/include/mach/spl.h
>>   create mode 100644 arch/mips/mach-mtmips/mt7628/serial.c
>>   create mode 100644 arch/mips/mach-mtmips/spl.c
>>   create mode 100644 arch/mips/mach-mtmips/spl_load.c
>>
>> diff --git a/Makefile b/Makefile
>> index 8013cbd9f9..1e18a37913 100644
>> --- a/Makefile
>> +++ b/Makefile
>> @@ -895,6 +895,7 @@ ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb-tegra.bin
>>   endif
>>   
>>   ALL-$(CONFIG_ARCH_MEDIATEK) += u-boot-mtk.bin
>> +ALL-$(CONFIG_ARCH_MTMIPS) += u-boot-mtmips.bin
>>   
>>   # Add optional build target if defined in board/cpu/soc headers
>>   ifneq ($(CONFIG_BUILD_TARGET),)
>> @@ -1664,6 +1665,14 @@ u-boot-mtk.bin: u-boot.bin FORCE
>>   	$(call if_changed,mkimage)
>>   endif
>>   
>> +ifeq ($(CONFIG_SPL),y)
>> +u-boot-mtmips.bin: u-boot.dtb u-boot-lzma.img spl/u-boot-spl.bin FORCE
>> +	$(call if_changed,binman)
>> +else
>> +u-boot-mtmips.bin: u-boot.bin FORCE
>> +	$(call if_changed,copy)
>> +endif
>> +
>>   ARCH_POSTLINK := $(wildcard $(srctree)/arch/$(ARCH)/Makefile.postlink)
>>   
>>   # Rule to link u-boot
>> diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
>> index 5f82caf8be..5f74f549b5 100644
>> --- a/arch/mips/Kconfig
>> +++ b/arch/mips/Kconfig
>> @@ -98,6 +98,9 @@ config ARCH_MTMIPS
>>   	select SUPPORTS_CPU_MIPS32_R2
>>   	select SUPPORTS_LITTLE_ENDIAN
>>   	select SYSRESET
>> +	select SUPPORT_SPL
>> +	select SPL_LZMA
>> +	select BINMAN
>>   
>>   config ARCH_JZ47XX
>>   	bool "Support Ingenic JZ47xx"
>> diff --git a/arch/mips/dts/mt7628-u-boot.dtsi b/arch/mips/dts/mt7628-u-boot.dtsi
>> new file mode 100644
>> index 0000000000..213959105f
>> --- /dev/null
>> +++ b/arch/mips/dts/mt7628-u-boot.dtsi
>> @@ -0,0 +1,24 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2020 MediaTek Inc.
>> + *
>> + * Author: Weijie Gao <weijie.gao at mediatek.com>
>> + */
>> +
>> +/ {
>> +	binman {
>> +		filename = "u-boot-mtmips.bin";
>> +		pad-byte = <0xff>;
>> +
>> +#ifdef CONFIG_SPL
>> +		u-boot-spl {
>> +		};
>> +
>> +		u-boot-lzma-img {
>> +		};
>> +#else
>> +		u-boot {
>> +		};
>> +#endif
>> +	};
>> +};
>> diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig
>> index 3f25de8b85..9b42d5b581 100644
>> --- a/arch/mips/mach-mtmips/Kconfig
>> +++ b/arch/mips/mach-mtmips/Kconfig
>> @@ -20,8 +20,16 @@ config SYS_ICACHE_LINE_SIZE
>>   	default 32
>>   
>>   config SYS_TEXT_BASE
>> +	default 0x9c000000 if !SPL
>> +	default 0x80200000 if SPL
>> +
>> +config SPL_TEXT_BASE
>>   	default 0x9c000000
>>   
>> +config SPL_LOADER_SUPPORT
>> +	bool
>> +	default y
>> +
> 
> this option should be moved to arch/mips/Kconfig and should be added
> with patch 15/21 because you use reference that option in the generic
> MIPS u-boot-spl.lds
> 
>>   choice
>>   	prompt "MediaTek MIPS SoC select"
>>   
>> @@ -34,6 +42,14 @@ config SOC_MT7628
>>   	select PINCTRL_MT7628
>>   	select MTK_SERIAL
>>   	select SYSRESET_RESETCTL
>> +	select SPL_SEPARATE_BSS if SPL
>> +	select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL
>> +	select SPL_OF_CONTROL if SPL_DM
>> +	select SPL_SIMPLE_BUS if SPL_DM
>> +	select SPL_DM_SERIAL if SPL_DM
>> +	select SPL_CLK if SPL_DM && SPL_SERIAL_SUPPORT
>> +	select SPL_SYSRESET if SPL_DM
>> +	select SPL_OF_LIBFDT if SPL_OF_CONTROL
>>   	help
>>   	  This supports MediaTek MT7628/MT7688.
>>   
>> @@ -88,6 +104,14 @@ endchoice
>>   config SUPPORTS_BOOT_RAM
>>   	bool
>>   
>> +config SPL_UART2_SPIS_PINMUX
>> +	bool "Use alternative pinmux for UART2 in SPL stage"
>> +	depends on SPL_SERIAL_SUPPORT
>> +	default n
>> +	help
>> +	  Select this if the UART2 of your board is connected to GPIO 16/17
>> +	  (shared with SPIS) rather than the usual GPIO 20/21.
>> +
>>   source "board/gardena/smart-gateway-mt7688/Kconfig"
>>   source "board/seeed/linkit-smart-7688/Kconfig"
>>   
>> diff --git a/arch/mips/mach-mtmips/Makefile b/arch/mips/mach-mtmips/Makefile
>> index 72f0369030..08d2a236d0 100644
>> --- a/arch/mips/mach-mtmips/Makefile
>> +++ b/arch/mips/mach-mtmips/Makefile
>> @@ -3,5 +3,6 @@
>>   obj-y += cpu.o
>>   obj-y += ddr_init.o
>>   obj-y += ddr_cal.o
>> +obj-$(CONFIG_SPL_BUILD) += spl.o spl_load.o
>>   
>>   obj-$(CONFIG_SOC_MT7628) += mt7628/
>> diff --git a/arch/mips/mach-mtmips/include/mach/serial.h b/arch/mips/mach-mtmips/include/mach/serial.h
>> new file mode 100644
>> index 0000000000..bfa246b428
>> --- /dev/null
>> +++ b/arch/mips/mach-mtmips/include/mach/serial.h
>> @@ -0,0 +1,13 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (C) 2020 MediaTek Inc.
>> + *
>> + * Author:  Weijie Gao <weijie.gao at mediatek.com>
>> + */
>> +
>> +#ifndef _MTMIPS_SERIAL_H_
>> +#define _MTMIPS_SERIAL_H_
>> +
>> +void mtmips_spl_serial_init(void);
>> +
>> +#endif /* _MTMIPS_SERIAL_H_ */
>> diff --git a/arch/mips/mach-mtmips/include/mach/spl.h b/arch/mips/mach-mtmips/include/mach/spl.h
>> new file mode 100644
>> index 0000000000..5674dd533e
>> --- /dev/null
>> +++ b/arch/mips/mach-mtmips/include/mach/spl.h
>> @@ -0,0 +1,14 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
>> + *
>> + * Author: Weijie Gao <weijie.gao at mediatek.com>
>> + */
>> +#ifndef	_MACH_MTMIPS_SPL_H_
>> +#define	_MACH_MTMIPS_SPL_H_
>> +
>> +#include <asm/spl.h>
>> +
>> +#define BOOT_DEVICE_MTMIPS_NOR	(BOOT_DEVICE_BOOTROM + 0x100)
>> +
>> +#endif /* _MACH_MTMIPS_SPL_H_ */
>> diff --git a/arch/mips/mach-mtmips/mt7628/Makefile b/arch/mips/mach-mtmips/mt7628/Makefile
>> index db62e90d77..7e139d5adf 100644
>> --- a/arch/mips/mach-mtmips/mt7628/Makefile
>> +++ b/arch/mips/mach-mtmips/mt7628/Makefile
>> @@ -3,3 +3,4 @@
>>   obj-y += lowlevel_init.o
>>   obj-y += init.o
>>   obj-y += ddr.o
>> +obj-$(CONFIG_SPL_BUILD) += serial.o
>> diff --git a/arch/mips/mach-mtmips/mt7628/serial.c b/arch/mips/mach-mtmips/mt7628/serial.c
>> new file mode 100644
>> index 0000000000..a7d324792d
>> --- /dev/null
>> +++ b/arch/mips/mach-mtmips/mt7628/serial.c
>> @@ -0,0 +1,34 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2020 MediaTek Inc.
>> + *
>> + * Author:  Weijie Gao <weijie.gao at mediatek.com>
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/io.h>
>> +#include "mt7628.h"
>> +
>> +void mtmips_spl_serial_init(void)
>> +{
>> +#ifdef CONFIG_SPL_SERIAL_SUPPORT
>> +	void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
>> +
>> +#if CONFIG_CONS_INDEX == 1
>> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART0_MODE_M);
>> +#elif CONFIG_CONS_INDEX == 2
>> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART1_MODE_M);
>> +#elif CONFIG_CONS_INDEX == 3
>> +	setbits_32(base + SYSCTL_AGPIO_CFG_REG, EPHY_GPIO_AIO_EN_M);
>> +#ifdef CONFIG_SPL_UART2_SPIS_PINMUX
>> +	setbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M);
>> +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M,
>> +		      1 << UART2_MODE_S);
>> +#else
>> +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M);
>> +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M,
>> +		      1 << SPIS_MODE_S);
>> +#endif /* CONFIG_SPL_UART2_SPIS_PINMUX */
>> +#endif /* CONFIG_CONS_INDEX */
>> +#endif /* CONFIG_SPL_SERIAL_SUPPORT */
>> +}
>> diff --git a/arch/mips/mach-mtmips/spl.c b/arch/mips/mach-mtmips/spl.c
>> new file mode 100644
>> index 0000000000..f12fb70d75
>> --- /dev/null
>> +++ b/arch/mips/mach-mtmips/spl.c
>> @@ -0,0 +1,31 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
>> + *
>> + * Author: Weijie Gao <weijie.gao at mediatek.com>
>> + */
>> +
>> +#include <common.h>
>> +#include <spl.h>
>> +#include <linux/sizes.h>
>> +#include <mach/serial.h>
>> +#include <mach/spl.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +void __noreturn board_init_f(ulong dummy)
>> +{
>> +	spl_init();
>> +
>> +#ifdef CONFIG_SPL_SERIAL_SUPPORT
>> +	mtmips_spl_serial_init();
>> +	preloader_console_init();
>> +#endif
>> +
>> +	board_init_r(NULL, 0);
>> +}
>> +
>> +void board_boot_order(u32 *spl_boot_list)
>> +{
>> +	spl_boot_list[0] = BOOT_DEVICE_MTMIPS_NOR;
>> +}
>> diff --git a/arch/mips/mach-mtmips/spl_load.c b/arch/mips/mach-mtmips/spl_load.c
>> new file mode 100644
>> index 0000000000..95dd491baa
>> --- /dev/null
>> +++ b/arch/mips/mach-mtmips/spl_load.c
>> @@ -0,0 +1,121 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
>> + *
>> + * Author: Weijie Gao <weijie.gao at mediatek.com>
>> + */
>> +
>> +#include <common.h>
>> +#include <cpu_func.h>
>> +#include <asm/sections.h>
>> +#include <linux/compiler.h>
>> +#include <linux/sizes.h>
>> +#include <mach/spl.h>
>> +#include <spl.h>
>> +
>> +#ifdef CONFIG_SPL_LZMA
>> +#include <lzma/LzmaTypes.h>
>> +#include <lzma/LzmaDec.h>
>> +#include <lzma/LzmaTools.h>
>> +#endif /* CONFIG_SPL_LZMA */
>> +
>> +#if CONFIG_IS_ENABLED(OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
>> +#include <fdt.h>
>> +#endif
>> +
>> +static ulong spl_dtb_size(void)
>> +{
>> +#if CONFIG_IS_ENABLED(OF_CONTROL)
>> +	void *fdt = __image_copy_end;
>> +
>> +	if (fdt_magic(fdt) == FDT_MAGIC)
>> +		return fdt_totalsize(fdt);
>> +#endif
>> +
>> +	return 0;
>> +}
>> +
>> +static int spl_try_load_image(struct spl_image_info *spl_image,
>> +			      void *image_addr)
>> +{
>> +	int ret;
>> +	uintptr_t dataptr;
>> +	struct image_header hdr;
>> +	size_t __maybe_unused lzma_len;
>> +
>> +	memcpy(&hdr, (const void *)image_addr, sizeof(hdr));
>> +
>> +	ret = spl_parse_image_header(spl_image, &hdr);
>> +	if (ret)
>> +		return ret;
>> +
>> +	if (!spl_image->entry_point)
>> +		spl_image->entry_point = spl_image->load_addr;
>> +
>> +	dataptr = (uintptr_t)image_addr + sizeof(hdr);
>> +
>> +	switch (hdr.ih_comp) {
>> +	case IH_COMP_NONE:
>> +		/*
>> +		 * Load real U-Boot from its location to its defined location
>> +		 * in SDRAM
>> +		 */
>> +		if (spl_image->load_addr != dataptr) {
>> +			memmove((void *)spl_image->load_addr, (void *)dataptr,
>> +				spl_image->size);
>> +		}
>> +		break;
>> +#ifdef CONFIG_SPL_LZMA
>> +	case IH_COMP_LZMA:
>> +		/*
>> +		 * Uncompress real U-Boot to its defined location in SDRAM
>> +		 */
>> +		lzma_len = SZ_8M;
>> +
>> +		ret = lzmaBuffToBuffDecompress((u8 *)spl_image->load_addr,
>> +					       &lzma_len, (u8 *)dataptr,
>> +					       spl_image->size);
>> +
>> +		if (ret) {
>> +			printf("Error: LZMA uncompression error: %d\n", ret);
>> +			return ret;
>> +		}
>> +
>> +		spl_image->size = lzma_len;
>> +		break;
>> +#endif /* CONFIG_SPL_LZMA */
>> +	default:
>> +		debug("Warning: Unsupported compression method found in image "
>> +		      "header at offset 0x%p\n", image_addr);
>> +		return -EINVAL;
>> +	}
>> +
>> +	flush_cache((unsigned long)spl_image->load_addr, spl_image->size);
>> +
>> +	return 0;
>> +}
>> +
>> +static int spl_mtk_nor_load_image(struct spl_image_info *spl_image,
>> +				  struct spl_boot_device *bootdev)
>> +{
>> +	ulong offset = spl_dtb_size();
>> +
>> +	/*
>> +	 * Loading of the payload to SDRAM is done with skipping of
>> +	 * the mkimage header
>> +	 */
>> +	spl_image->flags |= SPL_COPY_PAYLOAD_ONLY;
>> +
>> +	/* Try to boot without padding */
>> +	if (!spl_try_load_image(spl_image, (u8 *)__image_copy_end + offset))
>> +		return 0;
>> +
>> +#ifdef CONFIG_SYS_UBOOT_BASE
>> +	/* Try user defined offset */
>> +	if (!spl_try_load_image(spl_image, (void *)CONFIG_SYS_UBOOT_BASE))
>> +		return 0;
>> +#endif
>> +
>> +	return -EINVAL;
>> +}
>> +SPL_LOAD_IMAGE_METHOD("NOR", 0, BOOT_DEVICE_MTMIPS_NOR, spl_mtk_nor_load_image);
>>
> 
> maybe in a future patch series this could be refactored to a generic SPL
> decompressor in common/spl/ with spl_nor.c as the first user. Then it
> could be used by other archs or other SPL boot methods like SPI or NAND.

Yes, I fully agree with Daniel. Please move this into the common SPL code
so that it can be used by other platforms as well. This compression is a
great feature that should be generally available.

Thanks,
Stefan
Weijie Gao Jan. 19, 2020, 2:29 a.m. UTC | #4
On Fri, 2020-01-17 at 15:55 +0100, Stefan Roese wrote:
> Added Mauro to Cc
> 
> On 17.01.20 08:46, Weijie Gao wrote:
> > This patch adds SPL support for mtmips platform. The lowlevel architecture
> > is split into SPL and the rest parts are built into a memory loadable
> > u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
> > 
> > The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
> > not enabled and the memory bootable u-boot (u-boot.img) is generated
> > automatically so there is not need to add a separate config for it.
> > 
> > A lzma compressed payload (u-boot-lzma.img) is also generated and it will
> > be combined with u-boot-spl.bin to form the unified ROM bootable binary
> > u-boot-mtmips.bin.
> > 
> > A spl loader is added to support uncompress the payload.
> > 
> > Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
> > ---
> > Changes since v1:
> >    move spl loader into this patch.
> >    add full pinmux for all three uarts.
> >    add optional DM & DT support.
> > ---
> >   Makefile                                    |   9 ++
> >   arch/mips/Kconfig                           |   3 +
> >   arch/mips/dts/mt7628-u-boot.dtsi            |  24 ++++
> >   arch/mips/mach-mtmips/Kconfig               |  24 ++++
> >   arch/mips/mach-mtmips/Makefile              |   1 +
> >   arch/mips/mach-mtmips/include/mach/serial.h |  13 +++
> >   arch/mips/mach-mtmips/include/mach/spl.h    |  14 +++
> >   arch/mips/mach-mtmips/mt7628/Makefile       |   1 +
> >   arch/mips/mach-mtmips/mt7628/serial.c       |  34 ++++++
> >   arch/mips/mach-mtmips/spl.c                 |  31 +++++
> >   arch/mips/mach-mtmips/spl_load.c            | 121 ++++++++++++++++++++
> >   11 files changed, 275 insertions(+)
> >   create mode 100644 arch/mips/dts/mt7628-u-boot.dtsi
> >   create mode 100644 arch/mips/mach-mtmips/include/mach/serial.h
> >   create mode 100644 arch/mips/mach-mtmips/include/mach/spl.h
> >   create mode 100644 arch/mips/mach-mtmips/mt7628/serial.c
> >   create mode 100644 arch/mips/mach-mtmips/spl.c
> >   create mode 100644 arch/mips/mach-mtmips/spl_load.c
> > 
> > diff --git a/Makefile b/Makefile
> > index 8013cbd9f9..1e18a37913 100644
> > --- a/Makefile
> > +++ b/Makefile
> > @@ -895,6 +895,7 @@ ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb-tegra.bin
> >   endif
> >   
> >   ALL-$(CONFIG_ARCH_MEDIATEK) += u-boot-mtk.bin
> > +ALL-$(CONFIG_ARCH_MTMIPS) += u-boot-mtmips.bin
> >   
> >   # Add optional build target if defined in board/cpu/soc headers
> >   ifneq ($(CONFIG_BUILD_TARGET),)
> > @@ -1664,6 +1665,14 @@ u-boot-mtk.bin: u-boot.bin FORCE
> >   	$(call if_changed,mkimage)
> >   endif
> >   
> > +ifeq ($(CONFIG_SPL),y)
> > +u-boot-mtmips.bin: u-boot.dtb u-boot-lzma.img spl/u-boot-spl.bin FORCE
> > +	$(call if_changed,binman)
> > +else
> > +u-boot-mtmips.bin: u-boot.bin FORCE
> > +	$(call if_changed,copy)
> > +endif
> > +
> >   ARCH_POSTLINK := $(wildcard $(srctree)/arch/$(ARCH)/Makefile.postlink)
> >   
> >   # Rule to link u-boot
> > diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
> > index 5f82caf8be..5f74f549b5 100644
> > --- a/arch/mips/Kconfig
> > +++ b/arch/mips/Kconfig
> > @@ -98,6 +98,9 @@ config ARCH_MTMIPS
> >   	select SUPPORTS_CPU_MIPS32_R2
> >   	select SUPPORTS_LITTLE_ENDIAN
> >   	select SYSRESET
> > +	select SUPPORT_SPL
> > +	select SPL_LZMA
> > +	select BINMAN
> >   
> >   config ARCH_JZ47XX
> >   	bool "Support Ingenic JZ47xx"
> > diff --git a/arch/mips/dts/mt7628-u-boot.dtsi b/arch/mips/dts/mt7628-u-boot.dtsi
> > new file mode 100644
> > index 0000000000..213959105f
> > --- /dev/null
> > +++ b/arch/mips/dts/mt7628-u-boot.dtsi
> > @@ -0,0 +1,24 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 MediaTek Inc.
> > + *
> > + * Author: Weijie Gao <weijie.gao at mediatek.com>
> > + */
> > +
> > +/ {
> > +	binman {
> > +		filename = "u-boot-mtmips.bin";
> > +		pad-byte = <0xff>;
> > +
> > +#ifdef CONFIG_SPL
> > +		u-boot-spl {
> > +		};
> > +
> > +		u-boot-lzma-img {
> > +		};
> > +#else
> > +		u-boot {
> > +		};
> > +#endif
> > +	};
> > +};
> > diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig
> > index 3f25de8b85..9b42d5b581 100644
> > --- a/arch/mips/mach-mtmips/Kconfig
> > +++ b/arch/mips/mach-mtmips/Kconfig
> > @@ -20,8 +20,16 @@ config SYS_ICACHE_LINE_SIZE
> >   	default 32
> >   
> >   config SYS_TEXT_BASE
> > +	default 0x9c000000 if !SPL
> > +	default 0x80200000 if SPL
> > +
> > +config SPL_TEXT_BASE
> >   	default 0x9c000000
> >   
> > +config SPL_LOADER_SUPPORT
> > +	bool
> > +	default y
> > +
> >   choice
> >   	prompt "MediaTek MIPS SoC select"
> >   
> > @@ -34,6 +42,14 @@ config SOC_MT7628
> >   	select PINCTRL_MT7628
> >   	select MTK_SERIAL
> >   	select SYSRESET_RESETCTL
> > +	select SPL_SEPARATE_BSS if SPL
> > +	select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL
> > +	select SPL_OF_CONTROL if SPL_DM
> > +	select SPL_SIMPLE_BUS if SPL_DM
> > +	select SPL_DM_SERIAL if SPL_DM
> > +	select SPL_CLK if SPL_DM && SPL_SERIAL_SUPPORT
> > +	select SPL_SYSRESET if SPL_DM
> > +	select SPL_OF_LIBFDT if SPL_OF_CONTROL
> >   	help
> >   	  This supports MediaTek MT7628/MT7688.
> >   
> > @@ -88,6 +104,14 @@ endchoice
> >   config SUPPORTS_BOOT_RAM
> >   	bool
> >   
> > +config SPL_UART2_SPIS_PINMUX
> > +	bool "Use alternative pinmux for UART2 in SPL stage"
> > +	depends on SPL_SERIAL_SUPPORT
> > +	default n
> > +	help
> > +	  Select this if the UART2 of your board is connected to GPIO 16/17
> > +	  (shared with SPIS) rather than the usual GPIO 20/21.
> > +
> 
> Again, do you know if this is the option that needs to be selected
> for the VoCore2 board?
> 
> Thanks,
> Stefan

According to your discussions, I believe this is needed.

> 
> >   source "board/gardena/smart-gateway-mt7688/Kconfig"
> >   source "board/seeed/linkit-smart-7688/Kconfig"
> >   
> > diff --git a/arch/mips/mach-mtmips/Makefile b/arch/mips/mach-mtmips/Makefile
> > index 72f0369030..08d2a236d0 100644
> > --- a/arch/mips/mach-mtmips/Makefile
> > +++ b/arch/mips/mach-mtmips/Makefile
> > @@ -3,5 +3,6 @@
> >   obj-y += cpu.o
> >   obj-y += ddr_init.o
> >   obj-y += ddr_cal.o
> > +obj-$(CONFIG_SPL_BUILD) += spl.o spl_load.o
> >   
> >   obj-$(CONFIG_SOC_MT7628) += mt7628/
> > diff --git a/arch/mips/mach-mtmips/include/mach/serial.h b/arch/mips/mach-mtmips/include/mach/serial.h
> > new file mode 100644
> > index 0000000000..bfa246b428
> > --- /dev/null
> > +++ b/arch/mips/mach-mtmips/include/mach/serial.h
> > @@ -0,0 +1,13 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2020 MediaTek Inc.
> > + *
> > + * Author:  Weijie Gao <weijie.gao at mediatek.com>
> > + */
> > +
> > +#ifndef _MTMIPS_SERIAL_H_
> > +#define _MTMIPS_SERIAL_H_
> > +
> > +void mtmips_spl_serial_init(void);
> > +
> > +#endif /* _MTMIPS_SERIAL_H_ */
> > diff --git a/arch/mips/mach-mtmips/include/mach/spl.h b/arch/mips/mach-mtmips/include/mach/spl.h
> > new file mode 100644
> > index 0000000000..5674dd533e
> > --- /dev/null
> > +++ b/arch/mips/mach-mtmips/include/mach/spl.h
> > @@ -0,0 +1,14 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> > + *
> > + * Author: Weijie Gao <weijie.gao at mediatek.com>
> > + */
> > +#ifndef	_MACH_MTMIPS_SPL_H_
> > +#define	_MACH_MTMIPS_SPL_H_
> > +
> > +#include <asm/spl.h>
> > +
> > +#define BOOT_DEVICE_MTMIPS_NOR	(BOOT_DEVICE_BOOTROM + 0x100)
> > +
> > +#endif /* _MACH_MTMIPS_SPL_H_ */
> > diff --git a/arch/mips/mach-mtmips/mt7628/Makefile b/arch/mips/mach-mtmips/mt7628/Makefile
> > index db62e90d77..7e139d5adf 100644
> > --- a/arch/mips/mach-mtmips/mt7628/Makefile
> > +++ b/arch/mips/mach-mtmips/mt7628/Makefile
> > @@ -3,3 +3,4 @@
> >   obj-y += lowlevel_init.o
> >   obj-y += init.o
> >   obj-y += ddr.o
> > +obj-$(CONFIG_SPL_BUILD) += serial.o
> > diff --git a/arch/mips/mach-mtmips/mt7628/serial.c b/arch/mips/mach-mtmips/mt7628/serial.c
> > new file mode 100644
> > index 0000000000..a7d324792d
> > --- /dev/null
> > +++ b/arch/mips/mach-mtmips/mt7628/serial.c
> > @@ -0,0 +1,34 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 MediaTek Inc.
> > + *
> > + * Author:  Weijie Gao <weijie.gao at mediatek.com>
> > + */
> > +
> > +#include <common.h>
> > +#include <asm/io.h>
> > +#include "mt7628.h"
> > +
> > +void mtmips_spl_serial_init(void)
> > +{
> > +#ifdef CONFIG_SPL_SERIAL_SUPPORT
> > +	void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
> > +
> > +#if CONFIG_CONS_INDEX == 1
> > +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART0_MODE_M);
> > +#elif CONFIG_CONS_INDEX == 2
> > +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART1_MODE_M);
> > +#elif CONFIG_CONS_INDEX == 3
> > +	setbits_32(base + SYSCTL_AGPIO_CFG_REG, EPHY_GPIO_AIO_EN_M);
> > +#ifdef CONFIG_SPL_UART2_SPIS_PINMUX
> > +	setbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M);
> > +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M,
> > +		      1 << UART2_MODE_S);
> > +#else
> > +	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M);
> > +	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M,
> > +		      1 << SPIS_MODE_S);
> > +#endif /* CONFIG_SPL_UART2_SPIS_PINMUX */
> > +#endif /* CONFIG_CONS_INDEX */
> > +#endif /* CONFIG_SPL_SERIAL_SUPPORT */
> > +}
> > diff --git a/arch/mips/mach-mtmips/spl.c b/arch/mips/mach-mtmips/spl.c
> > new file mode 100644
> > index 0000000000..f12fb70d75
> > --- /dev/null
> > +++ b/arch/mips/mach-mtmips/spl.c
> > @@ -0,0 +1,31 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> > + *
> > + * Author: Weijie Gao <weijie.gao at mediatek.com>
> > + */
> > +
> > +#include <common.h>
> > +#include <spl.h>
> > +#include <linux/sizes.h>
> > +#include <mach/serial.h>
> > +#include <mach/spl.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +void __noreturn board_init_f(ulong dummy)
> > +{
> > +	spl_init();
> > +
> > +#ifdef CONFIG_SPL_SERIAL_SUPPORT
> > +	mtmips_spl_serial_init();
> > +	preloader_console_init();
> > +#endif
> > +
> > +	board_init_r(NULL, 0);
> > +}
> > +
> > +void board_boot_order(u32 *spl_boot_list)
> > +{
> > +	spl_boot_list[0] = BOOT_DEVICE_MTMIPS_NOR;
> > +}
> > diff --git a/arch/mips/mach-mtmips/spl_load.c b/arch/mips/mach-mtmips/spl_load.c
> > new file mode 100644
> > index 0000000000..95dd491baa
> > --- /dev/null
> > +++ b/arch/mips/mach-mtmips/spl_load.c
> > @@ -0,0 +1,121 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
> > + *
> > + * Author: Weijie Gao <weijie.gao at mediatek.com>
> > + */
> > +
> > +#include <common.h>
> > +#include <cpu_func.h>
> > +#include <asm/sections.h>
> > +#include <linux/compiler.h>
> > +#include <linux/sizes.h>
> > +#include <mach/spl.h>
> > +#include <spl.h>
> > +
> > +#ifdef CONFIG_SPL_LZMA
> > +#include <lzma/LzmaTypes.h>
> > +#include <lzma/LzmaDec.h>
> > +#include <lzma/LzmaTools.h>
> > +#endif /* CONFIG_SPL_LZMA */
> > +
> > +#if CONFIG_IS_ENABLED(OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
> > +#include <fdt.h>
> > +#endif
> > +
> > +static ulong spl_dtb_size(void)
> > +{
> > +#if CONFIG_IS_ENABLED(OF_CONTROL)
> > +	void *fdt = __image_copy_end;
> > +
> > +	if (fdt_magic(fdt) == FDT_MAGIC)
> > +		return fdt_totalsize(fdt);
> > +#endif
> > +
> > +	return 0;
> > +}
> > +
> > +static int spl_try_load_image(struct spl_image_info *spl_image,
> > +			      void *image_addr)
> > +{
> > +	int ret;
> > +	uintptr_t dataptr;
> > +	struct image_header hdr;
> > +	size_t __maybe_unused lzma_len;
> > +
> > +	memcpy(&hdr, (const void *)image_addr, sizeof(hdr));
> > +
> > +	ret = spl_parse_image_header(spl_image, &hdr);
> > +	if (ret)
> > +		return ret;
> > +
> > +	if (!spl_image->entry_point)
> > +		spl_image->entry_point = spl_image->load_addr;
> > +
> > +	dataptr = (uintptr_t)image_addr + sizeof(hdr);
> > +
> > +	switch (hdr.ih_comp) {
> > +	case IH_COMP_NONE:
> > +		/*
> > +		 * Load real U-Boot from its location to its defined location
> > +		 * in SDRAM
> > +		 */
> > +		if (spl_image->load_addr != dataptr) {
> > +			memmove((void *)spl_image->load_addr, (void *)dataptr,
> > +				spl_image->size);
> > +		}
> > +		break;
> > +#ifdef CONFIG_SPL_LZMA
> > +	case IH_COMP_LZMA:
> > +		/*
> > +		 * Uncompress real U-Boot to its defined location in SDRAM
> > +		 */
> > +		lzma_len = SZ_8M;
> > +
> > +		ret = lzmaBuffToBuffDecompress((u8 *)spl_image->load_addr,
> > +					       &lzma_len, (u8 *)dataptr,
> > +					       spl_image->size);
> > +
> > +		if (ret) {
> > +			printf("Error: LZMA uncompression error: %d\n", ret);
> > +			return ret;
> > +		}
> > +
> > +		spl_image->size = lzma_len;
> > +		break;
> > +#endif /* CONFIG_SPL_LZMA */
> > +	default:
> > +		debug("Warning: Unsupported compression method found in image "
> > +		      "header at offset 0x%p\n", image_addr);
> > +		return -EINVAL;
> > +	}
> > +
> > +	flush_cache((unsigned long)spl_image->load_addr, spl_image->size);
> > +
> > +	return 0;
> > +}
> > +
> > +static int spl_mtk_nor_load_image(struct spl_image_info *spl_image,
> > +				  struct spl_boot_device *bootdev)
> > +{
> > +	ulong offset = spl_dtb_size();
> > +
> > +	/*
> > +	 * Loading of the payload to SDRAM is done with skipping of
> > +	 * the mkimage header
> > +	 */
> > +	spl_image->flags |= SPL_COPY_PAYLOAD_ONLY;
> > +
> > +	/* Try to boot without padding */
> > +	if (!spl_try_load_image(spl_image, (u8 *)__image_copy_end + offset))
> > +		return 0;
> > +
> > +#ifdef CONFIG_SYS_UBOOT_BASE
> > +	/* Try user defined offset */
> > +	if (!spl_try_load_image(spl_image, (void *)CONFIG_SYS_UBOOT_BASE))
> > +		return 0;
> > +#endif
> > +
> > +	return -EINVAL;
> > +}
> > +SPL_LOAD_IMAGE_METHOD("NOR", 0, BOOT_DEVICE_MTMIPS_NOR, spl_mtk_nor_load_image);
> > 
> 
> Viele Grüße,
> Stefan
>
diff mbox series

Patch

diff --git a/Makefile b/Makefile
index 8013cbd9f9..1e18a37913 100644
--- a/Makefile
+++ b/Makefile
@@ -895,6 +895,7 @@  ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb-tegra.bin
 endif
 
 ALL-$(CONFIG_ARCH_MEDIATEK) += u-boot-mtk.bin
+ALL-$(CONFIG_ARCH_MTMIPS) += u-boot-mtmips.bin
 
 # Add optional build target if defined in board/cpu/soc headers
 ifneq ($(CONFIG_BUILD_TARGET),)
@@ -1664,6 +1665,14 @@  u-boot-mtk.bin: u-boot.bin FORCE
 	$(call if_changed,mkimage)
 endif
 
+ifeq ($(CONFIG_SPL),y)
+u-boot-mtmips.bin: u-boot.dtb u-boot-lzma.img spl/u-boot-spl.bin FORCE
+	$(call if_changed,binman)
+else
+u-boot-mtmips.bin: u-boot.bin FORCE
+	$(call if_changed,copy)
+endif
+
 ARCH_POSTLINK := $(wildcard $(srctree)/arch/$(ARCH)/Makefile.postlink)
 
 # Rule to link u-boot
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 5f82caf8be..5f74f549b5 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -98,6 +98,9 @@  config ARCH_MTMIPS
 	select SUPPORTS_CPU_MIPS32_R2
 	select SUPPORTS_LITTLE_ENDIAN
 	select SYSRESET
+	select SUPPORT_SPL
+	select SPL_LZMA
+	select BINMAN
 
 config ARCH_JZ47XX
 	bool "Support Ingenic JZ47xx"
diff --git a/arch/mips/dts/mt7628-u-boot.dtsi b/arch/mips/dts/mt7628-u-boot.dtsi
new file mode 100644
index 0000000000..213959105f
--- /dev/null
+++ b/arch/mips/dts/mt7628-u-boot.dtsi
@@ -0,0 +1,24 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ *
+ * Author: Weijie Gao <weijie.gao at mediatek.com>
+ */
+
+/ {
+	binman {
+		filename = "u-boot-mtmips.bin";
+		pad-byte = <0xff>;
+
+#ifdef CONFIG_SPL
+		u-boot-spl {
+		};
+
+		u-boot-lzma-img {
+		};
+#else
+		u-boot {
+		};
+#endif
+	};
+};
diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig
index 3f25de8b85..9b42d5b581 100644
--- a/arch/mips/mach-mtmips/Kconfig
+++ b/arch/mips/mach-mtmips/Kconfig
@@ -20,8 +20,16 @@  config SYS_ICACHE_LINE_SIZE
 	default 32
 
 config SYS_TEXT_BASE
+	default 0x9c000000 if !SPL
+	default 0x80200000 if SPL
+
+config SPL_TEXT_BASE
 	default 0x9c000000
 
+config SPL_LOADER_SUPPORT
+	bool
+	default y
+
 choice
 	prompt "MediaTek MIPS SoC select"
 
@@ -34,6 +42,14 @@  config SOC_MT7628
 	select PINCTRL_MT7628
 	select MTK_SERIAL
 	select SYSRESET_RESETCTL
+	select SPL_SEPARATE_BSS if SPL
+	select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL
+	select SPL_OF_CONTROL if SPL_DM
+	select SPL_SIMPLE_BUS if SPL_DM
+	select SPL_DM_SERIAL if SPL_DM
+	select SPL_CLK if SPL_DM && SPL_SERIAL_SUPPORT
+	select SPL_SYSRESET if SPL_DM
+	select SPL_OF_LIBFDT if SPL_OF_CONTROL
 	help
 	  This supports MediaTek MT7628/MT7688.
 
@@ -88,6 +104,14 @@  endchoice
 config SUPPORTS_BOOT_RAM
 	bool
 
+config SPL_UART2_SPIS_PINMUX
+	bool "Use alternative pinmux for UART2 in SPL stage"
+	depends on SPL_SERIAL_SUPPORT
+	default n
+	help
+	  Select this if the UART2 of your board is connected to GPIO 16/17
+	  (shared with SPIS) rather than the usual GPIO 20/21.
+
 source "board/gardena/smart-gateway-mt7688/Kconfig"
 source "board/seeed/linkit-smart-7688/Kconfig"
 
diff --git a/arch/mips/mach-mtmips/Makefile b/arch/mips/mach-mtmips/Makefile
index 72f0369030..08d2a236d0 100644
--- a/arch/mips/mach-mtmips/Makefile
+++ b/arch/mips/mach-mtmips/Makefile
@@ -3,5 +3,6 @@ 
 obj-y += cpu.o
 obj-y += ddr_init.o
 obj-y += ddr_cal.o
+obj-$(CONFIG_SPL_BUILD) += spl.o spl_load.o
 
 obj-$(CONFIG_SOC_MT7628) += mt7628/
diff --git a/arch/mips/mach-mtmips/include/mach/serial.h b/arch/mips/mach-mtmips/include/mach/serial.h
new file mode 100644
index 0000000000..bfa246b428
--- /dev/null
+++ b/arch/mips/mach-mtmips/include/mach/serial.h
@@ -0,0 +1,13 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ *
+ * Author:  Weijie Gao <weijie.gao at mediatek.com>
+ */
+
+#ifndef _MTMIPS_SERIAL_H_
+#define _MTMIPS_SERIAL_H_
+
+void mtmips_spl_serial_init(void);
+
+#endif /* _MTMIPS_SERIAL_H_ */
diff --git a/arch/mips/mach-mtmips/include/mach/spl.h b/arch/mips/mach-mtmips/include/mach/spl.h
new file mode 100644
index 0000000000..5674dd533e
--- /dev/null
+++ b/arch/mips/mach-mtmips/include/mach/spl.h
@@ -0,0 +1,14 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
+ *
+ * Author: Weijie Gao <weijie.gao at mediatek.com>
+ */
+#ifndef	_MACH_MTMIPS_SPL_H_
+#define	_MACH_MTMIPS_SPL_H_
+
+#include <asm/spl.h>
+
+#define BOOT_DEVICE_MTMIPS_NOR	(BOOT_DEVICE_BOOTROM + 0x100)
+
+#endif /* _MACH_MTMIPS_SPL_H_ */
diff --git a/arch/mips/mach-mtmips/mt7628/Makefile b/arch/mips/mach-mtmips/mt7628/Makefile
index db62e90d77..7e139d5adf 100644
--- a/arch/mips/mach-mtmips/mt7628/Makefile
+++ b/arch/mips/mach-mtmips/mt7628/Makefile
@@ -3,3 +3,4 @@ 
 obj-y += lowlevel_init.o
 obj-y += init.o
 obj-y += ddr.o
+obj-$(CONFIG_SPL_BUILD) += serial.o
diff --git a/arch/mips/mach-mtmips/mt7628/serial.c b/arch/mips/mach-mtmips/mt7628/serial.c
new file mode 100644
index 0000000000..a7d324792d
--- /dev/null
+++ b/arch/mips/mach-mtmips/mt7628/serial.c
@@ -0,0 +1,34 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ *
+ * Author:  Weijie Gao <weijie.gao at mediatek.com>
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include "mt7628.h"
+
+void mtmips_spl_serial_init(void)
+{
+#ifdef CONFIG_SPL_SERIAL_SUPPORT
+	void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
+
+#if CONFIG_CONS_INDEX == 1
+	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART0_MODE_M);
+#elif CONFIG_CONS_INDEX == 2
+	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART1_MODE_M);
+#elif CONFIG_CONS_INDEX == 3
+	setbits_32(base + SYSCTL_AGPIO_CFG_REG, EPHY_GPIO_AIO_EN_M);
+#ifdef CONFIG_SPL_UART2_SPIS_PINMUX
+	setbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M);
+	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M,
+		      1 << UART2_MODE_S);
+#else
+	clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M);
+	clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M,
+		      1 << SPIS_MODE_S);
+#endif /* CONFIG_SPL_UART2_SPIS_PINMUX */
+#endif /* CONFIG_CONS_INDEX */
+#endif /* CONFIG_SPL_SERIAL_SUPPORT */
+}
diff --git a/arch/mips/mach-mtmips/spl.c b/arch/mips/mach-mtmips/spl.c
new file mode 100644
index 0000000000..f12fb70d75
--- /dev/null
+++ b/arch/mips/mach-mtmips/spl.c
@@ -0,0 +1,31 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
+ *
+ * Author: Weijie Gao <weijie.gao at mediatek.com>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <linux/sizes.h>
+#include <mach/serial.h>
+#include <mach/spl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void __noreturn board_init_f(ulong dummy)
+{
+	spl_init();
+
+#ifdef CONFIG_SPL_SERIAL_SUPPORT
+	mtmips_spl_serial_init();
+	preloader_console_init();
+#endif
+
+	board_init_r(NULL, 0);
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	spl_boot_list[0] = BOOT_DEVICE_MTMIPS_NOR;
+}
diff --git a/arch/mips/mach-mtmips/spl_load.c b/arch/mips/mach-mtmips/spl_load.c
new file mode 100644
index 0000000000..95dd491baa
--- /dev/null
+++ b/arch/mips/mach-mtmips/spl_load.c
@@ -0,0 +1,121 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 MediaTek Inc. All Rights Reserved.
+ *
+ * Author: Weijie Gao <weijie.gao at mediatek.com>
+ */
+
+#include <common.h>
+#include <cpu_func.h>
+#include <asm/sections.h>
+#include <linux/compiler.h>
+#include <linux/sizes.h>
+#include <mach/spl.h>
+#include <spl.h>
+
+#ifdef CONFIG_SPL_LZMA
+#include <lzma/LzmaTypes.h>
+#include <lzma/LzmaDec.h>
+#include <lzma/LzmaTools.h>
+#endif /* CONFIG_SPL_LZMA */
+
+#if CONFIG_IS_ENABLED(OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
+#include <fdt.h>
+#endif
+
+static ulong spl_dtb_size(void)
+{
+#if CONFIG_IS_ENABLED(OF_CONTROL)
+	void *fdt = __image_copy_end;
+
+	if (fdt_magic(fdt) == FDT_MAGIC)
+		return fdt_totalsize(fdt);
+#endif
+
+	return 0;
+}
+
+static int spl_try_load_image(struct spl_image_info *spl_image,
+			      void *image_addr)
+{
+	int ret;
+	uintptr_t dataptr;
+	struct image_header hdr;
+	size_t __maybe_unused lzma_len;
+
+	memcpy(&hdr, (const void *)image_addr, sizeof(hdr));
+
+	ret = spl_parse_image_header(spl_image, &hdr);
+	if (ret)
+		return ret;
+
+	if (!spl_image->entry_point)
+		spl_image->entry_point = spl_image->load_addr;
+
+	dataptr = (uintptr_t)image_addr + sizeof(hdr);
+
+	switch (hdr.ih_comp) {
+	case IH_COMP_NONE:
+		/*
+		 * Load real U-Boot from its location to its defined location
+		 * in SDRAM
+		 */
+		if (spl_image->load_addr != dataptr) {
+			memmove((void *)spl_image->load_addr, (void *)dataptr,
+				spl_image->size);
+		}
+		break;
+#ifdef CONFIG_SPL_LZMA
+	case IH_COMP_LZMA:
+		/*
+		 * Uncompress real U-Boot to its defined location in SDRAM
+		 */
+		lzma_len = SZ_8M;
+
+		ret = lzmaBuffToBuffDecompress((u8 *)spl_image->load_addr,
+					       &lzma_len, (u8 *)dataptr,
+					       spl_image->size);
+
+		if (ret) {
+			printf("Error: LZMA uncompression error: %d\n", ret);
+			return ret;
+		}
+
+		spl_image->size = lzma_len;
+		break;
+#endif /* CONFIG_SPL_LZMA */
+	default:
+		debug("Warning: Unsupported compression method found in image "
+		      "header at offset 0x%p\n", image_addr);
+		return -EINVAL;
+	}
+
+	flush_cache((unsigned long)spl_image->load_addr, spl_image->size);
+
+	return 0;
+}
+
+static int spl_mtk_nor_load_image(struct spl_image_info *spl_image,
+				  struct spl_boot_device *bootdev)
+{
+	ulong offset = spl_dtb_size();
+
+	/*
+	 * Loading of the payload to SDRAM is done with skipping of
+	 * the mkimage header
+	 */
+	spl_image->flags |= SPL_COPY_PAYLOAD_ONLY;
+
+	/* Try to boot without padding */
+	if (!spl_try_load_image(spl_image, (u8 *)__image_copy_end + offset))
+		return 0;
+
+#ifdef CONFIG_SYS_UBOOT_BASE
+	/* Try user defined offset */
+	if (!spl_try_load_image(spl_image, (void *)CONFIG_SYS_UBOOT_BASE))
+		return 0;
+#endif
+
+	return -EINVAL;
+}
+SPL_LOAD_IMAGE_METHOD("NOR", 0, BOOT_DEVICE_MTMIPS_NOR, spl_mtk_nor_load_image);