@@ -55,8 +55,9 @@ static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
static unsigned int __dw_i2c_set_bus_speed(struct i2c_regs *i2c_base,
struct dw_scl_sda_cfg *scl_sda_cfg,
unsigned int speed,
- unsigned int bus_mhz)
+ unsigned int bus_clk)
{
+ ulong bus_khz = bus_clk / 1000;
enum i2c_speed_mode i2c_spd;
unsigned int cntl;
unsigned int hcnt, lcnt;
@@ -86,8 +87,8 @@ static unsigned int __dw_i2c_set_bus_speed(struct i2c_regs *i2c_base,
hcnt = scl_sda_cfg->fs_hcnt;
lcnt = scl_sda_cfg->fs_lcnt;
} else {
- hcnt = (bus_mhz * MIN_HS_SCL_HIGHTIME) / NANO_TO_MICRO;
- lcnt = (bus_mhz * MIN_HS_SCL_LOWTIME) / NANO_TO_MICRO;
+ hcnt = (bus_khz * MIN_HS_SCL_HIGHTIME) / NANO_TO_KILO;
+ lcnt = (bus_khz * MIN_HS_SCL_LOWTIME) / NANO_TO_KILO;
}
writel(hcnt, &i2c_base->ic_hs_scl_hcnt);
writel(lcnt, &i2c_base->ic_hs_scl_lcnt);
@@ -99,8 +100,8 @@ static unsigned int __dw_i2c_set_bus_speed(struct i2c_regs *i2c_base,
hcnt = scl_sda_cfg->ss_hcnt;
lcnt = scl_sda_cfg->ss_lcnt;
} else {
- hcnt = (bus_mhz * MIN_SS_SCL_HIGHTIME) / NANO_TO_MICRO;
- lcnt = (bus_mhz * MIN_SS_SCL_LOWTIME) / NANO_TO_MICRO;
+ hcnt = (bus_khz * MIN_SS_SCL_HIGHTIME) / NANO_TO_KILO;
+ lcnt = (bus_khz * MIN_SS_SCL_LOWTIME) / NANO_TO_KILO;
}
writel(hcnt, &i2c_base->ic_ss_scl_hcnt);
writel(lcnt, &i2c_base->ic_ss_scl_lcnt);
@@ -113,8 +114,8 @@ static unsigned int __dw_i2c_set_bus_speed(struct i2c_regs *i2c_base,
hcnt = scl_sda_cfg->fs_hcnt;
lcnt = scl_sda_cfg->fs_lcnt;
} else {
- hcnt = (bus_mhz * MIN_FS_SCL_HIGHTIME) / NANO_TO_MICRO;
- lcnt = (bus_mhz * MIN_FS_SCL_LOWTIME) / NANO_TO_MICRO;
+ hcnt = (bus_khz * MIN_FS_SCL_HIGHTIME) / NANO_TO_KILO;
+ lcnt = (bus_khz * MIN_FS_SCL_LOWTIME) / NANO_TO_KILO;
}
writel(hcnt, &i2c_base->ic_fs_scl_hcnt);
writel(lcnt, &i2c_base->ic_fs_scl_lcnt);
@@ -511,9 +512,6 @@ static int designware_i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
rate = clk_get_rate(&i2c->clk);
if (IS_ERR_VALUE(rate))
return -EINVAL;
-
- /* Convert to MHz */
- rate /= 1000000;
#else
rate = IC_CLK;
#endif
@@ -59,8 +59,8 @@ struct i2c_regs {
u32 comp_type;
};
-#define IC_CLK 166
-#define NANO_TO_MICRO 1000
+#define IC_CLK 166666666
+#define NANO_TO_KILO 1000000
/* High and low times in different speed modes (in ns) */
#define MIN_SS_SCL_HIGHTIME 4000
At present the driver uses an approximation for the bus clock, e.g. 166MHz instead of 166 2/3 MHz. This can result in small errors in the resulting I2C speed, perhaps 0.5% or so. Adjust the existing code to start from the accurate figure, even if later rounding reduces this accuracy. Update the bus speed code to work in KHz instead of MHz, which removes most of the error. Signed-off-by: Simon Glass <sjg at chromium.org> --- Changes in v2: None drivers/i2c/designware_i2c.c | 18 ++++++++---------- drivers/i2c/designware_i2c.h | 4 ++-- 2 files changed, 10 insertions(+), 12 deletions(-)