| Message ID | 1582812239-29480-1-git-send-email-simhavcs@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | display/bridge: dsi2lvds tc358775 driver | expand |
On 27.02.2020 15:03, Vinay Simha BN wrote: > dsi2lvds tc358775 bridge driver added > Tested in apq8016, ifc6309 board and panel > auo,b101xtn01 Just FYI, there exists already TC358764/5 driver for similar hw, but controlled via DSI bus. > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > --- > .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++ Bindings should be in separate patch and in yaml format. > drivers/gpu/drm/bridge/Kconfig | 10 + > drivers/gpu/drm/bridge/Makefile | 1 + > drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++ > 4 files changed, 804 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > create mode 100644 drivers/gpu/drm/bridge/tc358775.c > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > new file mode 100644 > index 0000000..c4c364d > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > @@ -0,0 +1,106 @@ > +Toshiba TC358775 DSI to LVDS bridge bindings > + > +Required properties: > + - compatible: "toshiba,tc358775" > + - reg: i2c address of the bridge, 0x0f > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should > + be one of 1, 2, 3 or 4. > + - tc, dual-link : To configure the LVDS transmitter either > + as single-link or dual-link. > + - tc, data-format: To configure the data formats > + 0 for VESA standard, 1 for JEIDA standard IMO, three properties above should be received from downstream device in runtime, not hardcoded into DT, however I am not sure if frameworks support it. > + - vdd-supply: 1.2V LVDS Power Supply > + - vddio-supply: 1.8V IO Power Supply > + - stby-gpios: Standby pin, Low active > + - reset-gpios: Hardware reset, Low active > + > +Required nodes: > + > +The TC358775 has two ports. Their connections are modelled using the OF > +graph bindings specified in Documentation/devicetree/bindings/graph.txt. > + > +- Video port 0 for the DSI input. The remote endpoint phandle should be a > + reference to a valid mipi_dsi_host device node. > +- Video port 1 for the LVDS output. > + > +Example: > + > + i2c@78b8000 { > + /* On High speed expansion */ > + label = "HS-I2C2"; > + status = "okay"; > + > + tc_bridge: bridge@f { > + status = "okay"; > + > + compatible = "toshiba,tc358775"; > + reg = <0x0f>; > + > + tc,dsi-lanes = <4>; > + tc,dual-link = <0>; > + tc,data-format = <1>; > + > + vdd-supply = <&pm8916_l2>; > + vddio-supply = <&pm8916_l6>; > + > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + d2l_in: endpoint { > + remote-endpoint = <&dsi0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + d2l_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > + }; > + }; > + > + panel: auo,b101xtn01 { > + status = "okay"; > + compatible = "auo,b101xtn01"; > + power-supply = <&pm8916_l14>; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&d2l_out>; > + }; > + }; > + }; > + > + mdss@1a00000 { > + status = "okay"; > + > + mdp@1a01000 { > + status = "okay"; > + }; > + > + dsi@1a98000 { > + status = "okay"; > + .. > + ports { > + port@1 { > + dsi0_out: endpoint { > + remote-endpoint = <&d2l_in>; > + data-lanes = <0 1 2 3>; > + }; > + }; > + }; > + }; > + > + dsi-phy@1a98300 { > + status = "okay"; > + .. > + }; > + }; > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig > index 8397bf7..d5528fa 100644 > --- a/drivers/gpu/drm/bridge/Kconfig > +++ b/drivers/gpu/drm/bridge/Kconfig > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 > ---help--- > Toshiba TC358767 eDP bridge chip driver. > > +config DRM_TOSHIBA_TC358775 > + tristate "Toshiba TC358775 LVDS bridge" > + depends on OF > + select DRM_KMS_HELPER > + select REGMAP_I2C > + select DRM_PANEL > + select DRM_MIPI_DSI > + ---help--- > + Toshiba TC358775 LVDS bridge chip driver. > + > config DRM_TI_TFP410 > tristate "TI TFP410 DVI/HDMI bridge" > depends on OF > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile > index 1eb5376..9b2c512 100644 > --- a/drivers/gpu/drm/bridge/Makefile > +++ b/drivers/gpu/drm/bridge/Makefile > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c > new file mode 100644 > index 0000000..3db0f49 > --- /dev/null > +++ b/drivers/gpu/drm/bridge/tc358775.c > @@ -0,0 +1,687 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * tc358775 DSI to LVDS bridge driver > + * > + * Copyright (C) 2020 InforceComputing > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. You can drop these statements, SPDX identifier is enough. > + */ > + > +/* #define DEBUG */ > +/* #define TC358775_DEBUG */ Please remove these development leftovers. > +#include <linux/clk.h> > +#include <linux/device.h> > +#include <linux/gpio/consumer.h> > +#include <linux/i2c.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/slab.h> > +#include <linux/regulator/consumer.h> Alphabetic order. > + > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_atomic_helper.h> > +#include <drm/drm_crtc_helper.h> > +#include <drm/drm_dp_helper.h> > +#include <drm/drm_of.h> > +#include <drm/drm_panel.h> > +#include <drm/drm_bridge.h> > +#include <drm/drm_probe_helper.h> ditto > + > +/* Registers */ > + > +/* DSI D-PHY Layer Registers */ > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ > + > +/* DSI PPI Layer Registers */ > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ > +#define PPI_BUSYPPI 0x0108 > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ > +#define PPI_LPTXTIMECNT 0x0114 > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ > + > +/* Analog timer function enable */ > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ > +#define PPI_D0S_CLRSIPOCOUNT 0x0164 > + > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ > + > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ > + > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ > +#define DSI_BUSYDSI 0x0208 > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ > + > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ > + > +#define DSIERRCNT 0x0300 /* DSI Error Count */ > +#define APLCTRL 0x0400 /* Application Layer Control */ > +#define RDPKTLN 0x0404 /* Command Read Packet Length */ > + > +#define VPCTRL 0x0450 /* Video Path Control */ > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ > +#define VTIM1 0x045C /* Vertical Timing Control 1 */ > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ > + > +/* Mux Input Select for LVDS LINK Input */ > +#define LVMX0003 0x0480 /* Bit 0 to 3 */ > +#define LVMX0407 0x0484 /* Bit 4 to 7 */ > +#define LVMX0811 0x0488 /* Bit 8 to 11 */ > +#define LVMX1215 0x048C /* Bit 12 to 15 */ > +#define LVMX1619 0x0490 /* Bit 16 to 19 */ > +#define LVMX2023 0x0494 /* Bit 20 to 23 */ > +#define LVMX2427 0x0498 /* Bit 24 to 27 */ > + > +#define LVCFG 0x049C /* LVDS Configuration */ > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ > +#define SYSSTAT 0x0500 /* System Status */ > +#define SYSRST 0x0504 /* System Reset */ > +/* GPIO Registers */ > +#define GPIOC 0x0520 /* GPIO Control */ > +#define GPIOO 0x0524 /* GPIO Output */ > +#define GPIOI 0x0528 /* GPIO Input */ > + > +/* I2C Registers */ > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ > +#define I2CMADDR 0x0544 /* I2C Master Addressing */ > +#define WDATAQ 0x0548 /* Write Data Queue */ > +#define RDATAQ 0x054C /* Read Data Queue */ > + > +/* Chip ID and Revision ID Register */ > +#define IDREG 0x0580 > + > +#define TC358775XBG_ID 0x00007500 > + > +/* Debug Registers */ > +#define DEBUG00 0x05A0 /* Debug */ > +#define DEBUG01 0x05A4 /* LVDS Data */ > + > +#define DSI_CLEN_BIT BIT(0) > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ > +#define LVCFG_LVEN_BIT BIT(0) > + > +#define L0EN BIT(1) > + > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val) Use u32 here and below, unit32_t is mainly for userspace interactions. > +{ > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & > + TC358775_VPCTRL_VSDELAY__MASK; > +} > + > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val) > +{ > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & > + TC358775_VPCTRL_OPXLFMT__MASK; > +} > + > +#define TC358775_VPCTRL_MSF__MASK 0x00000001 > +#define TC358775_VPCTRL_MSF__SHIFT 0 > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val) > +{ > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & > + TC358775_VPCTRL_MSF__MASK; > +} > + > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val) > +{ > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & > + TC358775_LVCFG_PCLKDIV__MASK; > +} > + > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 > +#define TC358775_LVCFG_LVDLINK__SHIFT 0 > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val) > +{ > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & > + TC358775_LVCFG_LVDLINK__MASK; > +} > + > +static const struct reg_sequence tc_fixed_registers[] = { > + { 0x013C, 0x00040006 }, > + { 0x0114, 0x00000004 }, > + { 0x0164, 0x00000003 }, > + { 0x0168, 0x00000003 }, > + { 0x016C, 0x00000003 }, > + { 0x0170, 0x00000003 }, use macros instead of magic numbers. > +}; > + > +static const struct reg_sequence tc_vesa_data_format_registers[] = { > + { 0x0480, 0x03020100 }, > + { 0x0484, 0x08050704 }, > + { 0x0488, 0x0F0E0A09 }, > + { 0x048C, 0x100D0C0B }, > + { 0x0490, 0x12111716 }, > + { 0x0494, 0x1B151413 }, > + { 0x0498, 0x061A1918 }, ditto > +}; > + > +static const char * const regulator_names[] = { > + "vdd", > + "vddio" > +}; > + > +struct tc_data { > + struct i2c_client *i2c; > + > + struct device *dev; > + struct regmap *regmap; > + > + struct drm_bridge bridge; > + struct drm_connector connector; > + struct drm_panel *panel; > + > + enum drm_connector_status status; unused field > + struct device_node *host_node; > + struct mipi_dsi_device *dsi; > + u8 num_dsi_lanes; > + > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; > + struct gpio_desc *reset_gpio; > + struct gpio_desc *stby_gpio; > + u32 rev; > + u8 dual_link; /* single-link or dual-link */ > + u8 data_format; /* VESA or JEIDA */ > +}; > + > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) > +{ > + return container_of(b, struct tc_data, bridge); > +} > + > +static inline struct tc_data *connector_to_tc(struct drm_connector *c) > +{ > + return container_of(c, struct tc_data, connector); > +} > + > +static void tc_bridge_pre_enable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + struct device *dev = &tc->dsi->dev; > + int ret; > + > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); > + if (ret < 0) { > + dev_err(dev, "regulator enable failed, %d\n", ret); > + return; > + } > + mdelay(10); > + > + gpiod_set_value(tc->stby_gpio, 0); > + mdelay(10); > + > + gpiod_set_value(tc->reset_gpio, 0); > + ndelay(50); > + > + drm_panel_prepare(tc->panel); > +} > + > +static void tc_bridge_disable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + struct device *dev = &tc->dsi->dev; > + int ret; > + > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); > + if (ret < 0) > + dev_err(dev, "regulator disable failed, %d\n", ret); > + mdelay(10); > + > + gpiod_set_value(tc->stby_gpio, 1); > + mdelay(10); > + > + gpiod_set_value(tc->reset_gpio, 1); > + ndelay(50); > + > + drm_panel_disable(tc->panel); I suspect the order should be different - ie reverse to the one pre_enable. Moreover since it reverts pre_enable it should be put into post_disable (except drm_panel_disable). > +} > + > +static void tc_bridge_post_disable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + > + drm_panel_unprepare(tc->panel); > +} > + > +#ifdef TC358775_DEBUG > +static u32 d2l_read(struct tc_data *tc, u16 reg) > +{ > + int ret; > + u32 data; > + > + ret = regmap_bulk_read(tc->regmap, reg, &data, 1); > + if (ret) > + return ret; > + > + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data); > + > + return data; > +} > +#endif I guess this leftover can be removed as well. > + > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) > +{ > + int ret = 0; > + > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); > + > +#ifdef TC358775_DEBUG > + d2l_read(tc, reg); > +#endif > + return ret; > +} > + > +static void tc_bridge_enable(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + int ret; > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; > + u32 val = 0; > + struct drm_display_mode *mode; > + > + mode = &bridge->encoder->crtc->state->adjusted_mode; > + > + hbpr = 0; > + hpw = mode->hsync_end - mode->hsync_start; > + vbpr = 0; > + vpw = mode->vsync_end - mode->vsync_start; > + > + htime1 = (hbpr << 16) + hpw; > + vtime1 = (vbpr << 16) + vpw; > + > + hfpr = mode->hsync_start - mode->hdisplay; > + hsize = mode->hdisplay; > + vfpr = mode->vsync_start - mode->vdisplay; > + vsize = mode->vdisplay; > + > + htime2 = (hfpr << 16) + hsize; > + vtime2 = (vfpr << 16) + vsize; > + > + ret = regmap_read(tc->regmap, IDREG, &tc->rev); > + if (ret) { > + dev_err(tc->dev, "can not read device ID: %d\n", ret); > + return; > + } > + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev); > + > + d2l_write(tc, SYSRST, 0x000000FF); > + mdelay(30); > + > + ret = regmap_register_patch(tc->regmap, > + tc_fixed_registers, > + ARRAY_SIZE(tc_fixed_registers)); > + if (ret) > + return; > + > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; > + d2l_write(tc, PPI_LANEENABLE, val); > + d2l_write(tc, DSI_LANEENABLE, val); > + > + d2l_write(tc, PPI_STARTPPI, 0x00000001); > + d2l_write(tc, DSI_STARTDSI, 0x00000001); > + > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value > + > + if (tc->connector.display_info.bpc == 8) {/* RGB888 */ > + val |= TC358775_VPCTRL_OPXLFMT(1); > + d2l_write(tc, VPCTRL, val); > + } else { /* RGB666 */ > + val |= TC358775_VPCTRL_MSF(1); > + d2l_write(tc, VPCTRL, val); > + } > + > + d2l_write(tc, HTIM1, htime1); > + d2l_write(tc, VTIM1, vtime1); > + d2l_write(tc, HTIM2, htime2); > + d2l_write(tc, VTIM2, vtime2); > + > + d2l_write(tc, VFUEN, 0x00000001); > + d2l_write(tc, SYSRST, 0x00000004); > + d2l_write(tc, LVPHY0, 0x00040006); > + > + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */ > + ret = regmap_register_patch > + (tc->regmap, > + tc_vesa_data_format_registers, > + ARRAY_SIZE(tc_vesa_data_format_registers)); > + if (ret) > + return; > + } > + > + d2l_write(tc, VFUEN, 0x00000001); > + > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; > + if (tc->dual_link) > + val |= TC358775_LVCFG_LVDLINK(1); > + > + d2l_write(tc, LVCFG, val); > + > + drm_panel_enable(tc->panel); > +} > + > +static int tc_connector_get_modes(struct drm_connector *connector) > +{ > + struct tc_data *tc = connector_to_tc(connector); > + struct edid *edid; > + unsigned int count; > + > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { > + count = tc->panel->funcs->get_modes(tc->panel, connector); > + if (count > 0) > + return count; > + } > + > + edid = drm_get_edid(connector, tc->i2c->adapter); > + if (!edid) > + return 0; > + > + drm_connector_update_edid_property(connector, edid); > + count = drm_add_edid_modes(connector, edid); > + kfree(edid); > + > + return count; > +} > + > +static int tc_connector_mode_valid(struct drm_connector *connector, > + struct drm_display_mode *mode) > +{ > + struct tc_data *tc = connector_to_tc(connector); > + > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ > + if ((mode->clock > 135000 && tc->dual_link == 0) || > + (mode->clock > 270000 && tc->dual_link == 1)) > + return MODE_CLOCK_HIGH; > + > + return MODE_OK; > +} > + > +static struct drm_encoder * > +tc_connector_best_encoder(struct drm_connector *connector) > +{ > + struct tc_data *tc = connector_to_tc(connector); > + > + return tc->bridge.encoder; > +} > + > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { > + .get_modes = tc_connector_get_modes, > + .mode_valid = tc_connector_mode_valid, > + .best_encoder = tc_connector_best_encoder, > +}; > + > +static const struct drm_connector_funcs tc_connector_funcs = { > + .fill_modes = drm_helper_probe_single_connector_modes, > + .destroy = drm_connector_cleanup, > + .reset = drm_atomic_helper_connector_reset, > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > +}; > + > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) > +{ > + u32 num_lanes; > + u8 dual_link, data_format; > + > + of_property_read_u8(np, "tc,dual-link", &dual_link); > + of_property_read_u8(np, "tc,data-format", &data_format); > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); > + > + if (num_lanes < 1 || num_lanes > 4) > + return -EINVAL; > + > + tc->num_dsi_lanes = num_lanes; > + tc->dual_link = dual_link; > + tc->data_format = data_format; > + > + tc->host_node = of_graph_get_remote_node(np, 0, 0); > + if (!tc->host_node) > + return -ENODEV; > + > + of_node_put(tc->host_node); > + > + return 0; > +} > + > +int tc358775_attach_dsi(struct tc_data *tc) > +{ > + struct device *dev = &tc->i2c->dev; > + struct mipi_dsi_host *host; > + struct mipi_dsi_device *dsi; > + int ret = 0; > + const struct mipi_dsi_device_info info = { .type = "tc358775", > + .channel = 0, > + .node = NULL, > + }; > + > + host = of_find_mipi_dsi_host_by_node(tc->host_node); > + if (!host) { > + dev_err(dev, "failed to find dsi host\n"); > + return -EPROBE_DEFER; > + } > + > + dsi = mipi_dsi_device_register_full(host, &info); > + if (IS_ERR(dsi)) { > + dev_err(dev, "failed to create dsi device\n"); > + ret = PTR_ERR(dsi); > + goto err_dsi_device; > + } > + > + tc->dsi = dsi; > + > + dsi->lanes = tc->num_dsi_lanes; > + dsi->format = MIPI_DSI_FMT_RGB888; > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; > + > + ret = mipi_dsi_attach(dsi); > + if (ret < 0) { > + dev_err(dev, "failed to attach dsi to host\n"); > + goto err_dsi_attach; > + } > + > + return 0; > + > +err_dsi_attach: > + mipi_dsi_device_unregister(dsi); > +err_dsi_device: > + return ret; > +} > + > +static int tc_bridge_attach(struct drm_bridge *bridge) > +{ > + struct tc_data *tc = bridge_to_tc(bridge); > + struct drm_device *drm = bridge->dev; > + int ret; > + > + /* Create LVDS connector */ > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, > + DRM_MODE_CONNECTOR_LVDS); > + if (ret) > + return ret; > + > + if (tc->panel) > + drm_panel_attach(tc->panel, &tc->connector); > + > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); > + > + ret = tc358775_attach_dsi(tc); Ignored retval. > + > + return 0; > +} > + > +static const struct drm_bridge_funcs tc_bridge_funcs = { > + .attach = tc_bridge_attach, > + .pre_enable = tc_bridge_pre_enable, > + .enable = tc_bridge_enable, > + .disable = tc_bridge_disable, > + .post_disable = tc_bridge_post_disable, > +}; > + > +static const struct regmap_config tc_regmap_config = { > + .name = "tc358775", > + .reg_bits = 16, > + .val_bits = 32, > + .reg_stride = 4, > + .max_register = 0x05A8, > + .cache_type = REGCACHE_RBTREE, > + .reg_format_endian = REGMAP_ENDIAN_BIG, > + .val_format_endian = REGMAP_ENDIAN_LITTLE, > +}; > + > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) > +{ > + struct device *dev = &client->dev; > + struct tc_data *tc; > + int ret; > + unsigned int i; > + > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); > + if (!tc) > + return -ENOMEM; > + > + tc->dev = dev; > + tc->i2c = client; > + tc->status = connector_status_connected; > + > + /* port@1 is the output port */ > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); > + if (ret && ret != -ENODEV) > + return ret; > + > + ret = tc358775_parse_dt(dev->of_node, tc); > + if (ret) > + return ret; > + > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) > + tc->supplies[i].supply = regulator_names[i]; > + > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), > + tc->supplies); > + if (ret < 0) > + dev_err(dev, "failed to init regulator, ret=%d\n", ret); > + > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); > + if (IS_ERR(tc->stby_gpio)) { > + ret = PTR_ERR(tc->stby_gpio); > + dev_err(dev, "cannot get stby-gpio %d\n", ret); > + return ret; > + } > + > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > + if (IS_ERR(tc->reset_gpio)) { > + ret = PTR_ERR(tc->reset_gpio); > + dev_err(dev, "cannot get reset-gpios %d\n", ret); > + return ret; > + } > + > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); > + if (IS_ERR(tc->regmap)) { > + ret = PTR_ERR(tc->regmap); > + dev_err(dev, "Failed to initialize regmap: %d\n", ret); > + return ret; > + } > + > + tc->bridge.funcs = &tc_bridge_funcs; > + tc->bridge.of_node = dev->of_node; > + drm_bridge_add(&tc->bridge); > + > + i2c_set_clientdata(client, tc); > + > + return 0; > +} > + > +static int tc_remove(struct i2c_client *client) > +{ > + struct tc_data *tc = i2c_get_clientdata(client); > + > + drm_bridge_remove(&tc->bridge); > + > + return 0; > +} > + > +static const struct i2c_device_id tc358775_i2c_ids[] = { > + { "tc358775", 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); > + > +static const struct of_device_id tc358775_of_ids[] = { > + { .compatible = "toshiba,tc358775", }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, tc358775_of_ids); > + > +static struct i2c_driver tc358775_driver = { > + .driver = { > + .name = "tc358775", > + .of_match_table = tc358775_of_ids, > + }, > + .id_table = tc358775_i2c_ids, > + .probe = tc_probe, > + .remove = tc_remove, > +}; > +module_i2c_driver(tc358775_driver); > + > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); maybe better: tc358775 DSI/LVDS bridge driver Regards Andrzej > +MODULE_LICENSE("GPL v2");
hi andrzej, I had a doubt In the tc358764 driver,VP_CTRL, VP_CTRL_VSDELAY(15) is hardcoded to 15, but this has to be dynamic based on the resolution of panel used? Please see the reply inline. On Tue, Mar 3, 2020 at 8:39 PM Andrzej Hajda <a.hajda@samsung.com> wrote: > > On 27.02.2020 15:03, Vinay Simha BN wrote: > > dsi2lvds tc358775 bridge driver added > > Tested in apq8016, ifc6309 board and panel > > auo,b101xtn01 > > > Just FYI, there exists already TC358764/5 driver for similar hw, but > controlled via DSI bus. There is not much difference between these two chips, but still the dsi read access for 775 does not works. TC358764/5 - 800Mbps per lane, 3.2Gbps TC358775 - 1Gbps per lane, 4Gbps. tc358775 chip details - https://download.t-firefly.com/product/RK3399/Docs/Chip%20Specifications/TC358774XBG_75XBG_V1%204nm.pdf I am able to configure the tc358775 chip by i2c, but from dsi it fails i tried accessing the tc358775 chip by dsi using apq8016-qcom , but it fails to read the chip id itself. Please suggest if you any inputs for this issue. https://github.com/vinaysimhabn/kernel-msm/commits/5.6.0-rc3-dsi2lvds-dsi [ 4.582405] tc358764 1a98000.dsi.0: read: 1408, addr: 0 [ 4.582426] tc358764 1a98000.dsi.0: ID: 0x0 [ 4.582451] tc358764 1a98000.dsi.0: error initializing bridge (-22) [ 4.796220] dsi_cmds2buf_tx: cmd dma tx failed, type=0x24, data0=0x80, len=4 [ 4.796244] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 [ 4.796266] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 [ 4.796288] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 [ 4.796310] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 [ 4.796319] msm_dsi_host_cmd_rx:Invalid response cmd > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > --- > > .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++ > > > Bindings should be in separate patch and in yaml format. > > > > drivers/gpu/drm/bridge/Kconfig | 10 + > > drivers/gpu/drm/bridge/Makefile | 1 + > > drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++ > > 4 files changed, 804 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > create mode 100644 drivers/gpu/drm/bridge/tc358775.c > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > new file mode 100644 > > index 0000000..c4c364d > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > @@ -0,0 +1,106 @@ > > +Toshiba TC358775 DSI to LVDS bridge bindings > > + > > +Required properties: > > + - compatible: "toshiba,tc358775" > > + - reg: i2c address of the bridge, 0x0f > > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should > > + be one of 1, 2, 3 or 4. > > + - tc, dual-link : To configure the LVDS transmitter either > > + as single-link or dual-link. > > + - tc, data-format: To configure the data formats > > + 0 for VESA standard, 1 for JEIDA standard > > > IMO, three properties above should be received from downstream device in > runtime, not hardcoded into DT, however I am not sure if frameworks > support it. > > > + - vdd-supply: 1.2V LVDS Power Supply > > + - vddio-supply: 1.8V IO Power Supply > > + - stby-gpios: Standby pin, Low active > > + - reset-gpios: Hardware reset, Low active > > + > > +Required nodes: > > + > > +The TC358775 has two ports. Their connections are modelled using the OF > > +graph bindings specified in Documentation/devicetree/bindings/graph.txt. > > + > > +- Video port 0 for the DSI input. The remote endpoint phandle should be a > > + reference to a valid mipi_dsi_host device node. > > +- Video port 1 for the LVDS output. > > + > > +Example: > > + > > + i2c@78b8000 { > > + /* On High speed expansion */ > > + label = "HS-I2C2"; > > + status = "okay"; > > + > > + tc_bridge: bridge@f { > > + status = "okay"; > > + > > + compatible = "toshiba,tc358775"; > > + reg = <0x0f>; > > + > > + tc,dsi-lanes = <4>; > > + tc,dual-link = <0>; > > + tc,data-format = <1>; > > + > > + vdd-supply = <&pm8916_l2>; > > + vddio-supply = <&pm8916_l6>; > > + > > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@0 { > > + reg = <0>; > > + d2l_in: endpoint { > > + remote-endpoint = <&dsi0_out>; > > + }; > > + }; > > + > > + port@1 { > > + reg = <1>; > > + d2l_out: endpoint { > > + remote-endpoint = <&panel_in>; > > + }; > > + }; > > + }; > > + }; > > + }; > > + > > + panel: auo,b101xtn01 { > > + status = "okay"; > > + compatible = "auo,b101xtn01"; > > + power-supply = <&pm8916_l14>; > > + > > + port { > > + panel_in: endpoint { > > + remote-endpoint = <&d2l_out>; > > + }; > > + }; > > + }; > > + > > + mdss@1a00000 { > > + status = "okay"; > > + > > + mdp@1a01000 { > > + status = "okay"; > > + }; > > + > > + dsi@1a98000 { > > + status = "okay"; > > + .. > > + ports { > > + port@1 { > > + dsi0_out: endpoint { > > + remote-endpoint = <&d2l_in>; > > + data-lanes = <0 1 2 3>; > > + }; > > + }; > > + }; > > + }; > > + > > + dsi-phy@1a98300 { > > + status = "okay"; > > + .. > > + }; > > + }; > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig > > index 8397bf7..d5528fa 100644 > > --- a/drivers/gpu/drm/bridge/Kconfig > > +++ b/drivers/gpu/drm/bridge/Kconfig > > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 > > ---help--- > > Toshiba TC358767 eDP bridge chip driver. > > > > +config DRM_TOSHIBA_TC358775 > > + tristate "Toshiba TC358775 LVDS bridge" > > + depends on OF > > + select DRM_KMS_HELPER > > + select REGMAP_I2C > > + select DRM_PANEL > > + select DRM_MIPI_DSI > > + ---help--- > > + Toshiba TC358775 LVDS bridge chip driver. > > + > > config DRM_TI_TFP410 > > tristate "TI TFP410 DVI/HDMI bridge" > > depends on OF > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile > > index 1eb5376..9b2c512 100644 > > --- a/drivers/gpu/drm/bridge/Makefile > > +++ b/drivers/gpu/drm/bridge/Makefile > > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o > > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o > > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o > > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o > > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o > > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ > > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o > > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c > > new file mode 100644 > > index 0000000..3db0f49 > > --- /dev/null > > +++ b/drivers/gpu/drm/bridge/tc358775.c > > @@ -0,0 +1,687 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * tc358775 DSI to LVDS bridge driver > > + * > > + * Copyright (C) 2020 InforceComputing > > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> > > + * > > + * This program is free software; you can redistribute it and/or modify > > + * it under the terms of the GNU General Public License as published by > > + * the Free Software Foundation; either version 2 of the License, or > > + * (at your option) any later version. > > + * > > + * This program is distributed in the hope that it will be useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > > You can drop these statements, SPDX identifier is enough. > > > > + */ > > + > > +/* #define DEBUG */ > > +/* #define TC358775_DEBUG */ > > > Please remove these development leftovers. > > > > +#include <linux/clk.h> > > +#include <linux/device.h> > > +#include <linux/gpio/consumer.h> > > +#include <linux/i2c.h> > > +#include <linux/kernel.h> > > +#include <linux/module.h> > > +#include <linux/regmap.h> > > +#include <linux/slab.h> > > +#include <linux/regulator/consumer.h> > Alphabetic order. > > + > > +#include <drm/drm_mipi_dsi.h> > > +#include <drm/drm_atomic_helper.h> > > +#include <drm/drm_crtc_helper.h> > > +#include <drm/drm_dp_helper.h> > > +#include <drm/drm_of.h> > > +#include <drm/drm_panel.h> > > +#include <drm/drm_bridge.h> > > +#include <drm/drm_probe_helper.h> > ditto > > + > > +/* Registers */ > > + > > +/* DSI D-PHY Layer Registers */ > > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ > > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ > > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ > > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ > > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ > > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ > > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ > > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ > > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ > > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ > > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ > > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ > > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ > > + > > +/* DSI PPI Layer Registers */ > > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ > > +#define PPI_BUSYPPI 0x0108 > > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ > > +#define PPI_LPTXTIMECNT 0x0114 > > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ > > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ > > + > > +/* Analog timer function enable */ > > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ > > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ > > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ > > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ > > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ > > +#define PPI_D0S_CLRSIPOCOUNT 0x0164 > > + > > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ > > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ > > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ > > + > > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ > > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ > > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ > > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ > > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ > > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ > > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ > > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ > > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ > > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ > > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ > > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ > > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ > > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ > > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ > > + > > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ > > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ > > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ > > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ > > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ > > +#define DSI_BUSYDSI 0x0208 > > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ > > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ > > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ > > + > > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ > > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ > > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ > > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ > > + > > +#define DSIERRCNT 0x0300 /* DSI Error Count */ > > +#define APLCTRL 0x0400 /* Application Layer Control */ > > +#define RDPKTLN 0x0404 /* Command Read Packet Length */ > > + > > +#define VPCTRL 0x0450 /* Video Path Control */ > > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ > > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ > > +#define VTIM1 0x045C /* Vertical Timing Control 1 */ > > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ > > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ > > + > > +/* Mux Input Select for LVDS LINK Input */ > > +#define LVMX0003 0x0480 /* Bit 0 to 3 */ > > +#define LVMX0407 0x0484 /* Bit 4 to 7 */ > > +#define LVMX0811 0x0488 /* Bit 8 to 11 */ > > +#define LVMX1215 0x048C /* Bit 12 to 15 */ > > +#define LVMX1619 0x0490 /* Bit 16 to 19 */ > > +#define LVMX2023 0x0494 /* Bit 20 to 23 */ > > +#define LVMX2427 0x0498 /* Bit 24 to 27 */ > > + > > +#define LVCFG 0x049C /* LVDS Configuration */ > > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ > > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ > > +#define SYSSTAT 0x0500 /* System Status */ > > +#define SYSRST 0x0504 /* System Reset */ > > +/* GPIO Registers */ > > +#define GPIOC 0x0520 /* GPIO Control */ > > +#define GPIOO 0x0524 /* GPIO Output */ > > +#define GPIOI 0x0528 /* GPIO Input */ > > + > > +/* I2C Registers */ > > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ > > +#define I2CMADDR 0x0544 /* I2C Master Addressing */ > > +#define WDATAQ 0x0548 /* Write Data Queue */ > > +#define RDATAQ 0x054C /* Read Data Queue */ > > + > > +/* Chip ID and Revision ID Register */ > > +#define IDREG 0x0580 > > + > > +#define TC358775XBG_ID 0x00007500 > > + > > +/* Debug Registers */ > > +#define DEBUG00 0x05A0 /* Debug */ > > +#define DEBUG01 0x05A4 /* LVDS Data */ > > + > > +#define DSI_CLEN_BIT BIT(0) > > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ > > +#define LVCFG_LVEN_BIT BIT(0) > > + > > +#define L0EN BIT(1) > > + > > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 > > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 > > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val) > > > Use u32 here and below, unit32_t is mainly for userspace interactions. > > > > +{ > > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & > > + TC358775_VPCTRL_VSDELAY__MASK; > > +} > > + > > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 > > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 > > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val) > > +{ > > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & > > + TC358775_VPCTRL_OPXLFMT__MASK; > > +} > > + > > +#define TC358775_VPCTRL_MSF__MASK 0x00000001 > > +#define TC358775_VPCTRL_MSF__SHIFT 0 > > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val) > > +{ > > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & > > + TC358775_VPCTRL_MSF__MASK; > > +} > > + > > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 > > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 > > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val) > > +{ > > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & > > + TC358775_LVCFG_PCLKDIV__MASK; > > +} > > + > > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 > > +#define TC358775_LVCFG_LVDLINK__SHIFT 0 > > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val) > > +{ > > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & > > + TC358775_LVCFG_LVDLINK__MASK; > > +} > > + > > +static const struct reg_sequence tc_fixed_registers[] = { > > + { 0x013C, 0x00040006 }, > > + { 0x0114, 0x00000004 }, > > + { 0x0164, 0x00000003 }, > > + { 0x0168, 0x00000003 }, > > + { 0x016C, 0x00000003 }, > > + { 0x0170, 0x00000003 }, > > > use macros instead of magic numbers. > > > > +}; > > + > > +static const struct reg_sequence tc_vesa_data_format_registers[] = { > > + { 0x0480, 0x03020100 }, > > + { 0x0484, 0x08050704 }, > > + { 0x0488, 0x0F0E0A09 }, > > + { 0x048C, 0x100D0C0B }, > > + { 0x0490, 0x12111716 }, > > + { 0x0494, 0x1B151413 }, > > + { 0x0498, 0x061A1918 }, > ditto > > +}; > > + > > +static const char * const regulator_names[] = { > > + "vdd", > > + "vddio" > > +}; > > + > > +struct tc_data { > > + struct i2c_client *i2c; > > + > > + struct device *dev; > > + struct regmap *regmap; > > + > > + struct drm_bridge bridge; > > + struct drm_connector connector; > > + struct drm_panel *panel; > > + > > + enum drm_connector_status status; > unused field > > + struct device_node *host_node; > > + struct mipi_dsi_device *dsi; > > + u8 num_dsi_lanes; > > + > > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; > > + struct gpio_desc *reset_gpio; > > + struct gpio_desc *stby_gpio; > > + u32 rev; > > + u8 dual_link; /* single-link or dual-link */ > > + u8 data_format; /* VESA or JEIDA */ > > +}; > > + > > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) > > +{ > > + return container_of(b, struct tc_data, bridge); > > +} > > + > > +static inline struct tc_data *connector_to_tc(struct drm_connector *c) > > +{ > > + return container_of(c, struct tc_data, connector); > > +} > > + > > +static void tc_bridge_pre_enable(struct drm_bridge *bridge) > > +{ > > + struct tc_data *tc = bridge_to_tc(bridge); > > + struct device *dev = &tc->dsi->dev; > > + int ret; > > + > > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); > > + if (ret < 0) { > > + dev_err(dev, "regulator enable failed, %d\n", ret); > > + return; > > + } > > + mdelay(10); > > + > > + gpiod_set_value(tc->stby_gpio, 0); > > + mdelay(10); > > + > > + gpiod_set_value(tc->reset_gpio, 0); > > + ndelay(50); > > + > > + drm_panel_prepare(tc->panel); > > +} > > + > > +static void tc_bridge_disable(struct drm_bridge *bridge) > > +{ > > + struct tc_data *tc = bridge_to_tc(bridge); > > + struct device *dev = &tc->dsi->dev; > > + int ret; > > + > > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); > > + if (ret < 0) > > + dev_err(dev, "regulator disable failed, %d\n", ret); > > + mdelay(10); > > + > > + gpiod_set_value(tc->stby_gpio, 1); > > + mdelay(10); > > + > > + gpiod_set_value(tc->reset_gpio, 1); > > + ndelay(50); > > + > > + drm_panel_disable(tc->panel); > > I suspect the order should be different - ie reverse to the one pre_enable. > > Moreover since it reverts pre_enable it should be put into post_disable > (except drm_panel_disable). > > > +} > > + > > +static void tc_bridge_post_disable(struct drm_bridge *bridge) > > +{ > > + struct tc_data *tc = bridge_to_tc(bridge); > > + > > + drm_panel_unprepare(tc->panel); > > +} > > + > > +#ifdef TC358775_DEBUG > > +static u32 d2l_read(struct tc_data *tc, u16 reg) > > +{ > > + int ret; > > + u32 data; > > + > > + ret = regmap_bulk_read(tc->regmap, reg, &data, 1); > > + if (ret) > > + return ret; > > + > > + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data); > > + > > + return data; > > +} > > +#endif > > > I guess this leftover can be removed as well. > > > > + > > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) > > +{ > > + int ret = 0; > > + > > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); > > + > > +#ifdef TC358775_DEBUG > > + d2l_read(tc, reg); > > +#endif > > + return ret; > > +} > > + > > +static void tc_bridge_enable(struct drm_bridge *bridge) > > +{ > > + struct tc_data *tc = bridge_to_tc(bridge); > > + int ret; > > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; > > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; > > + u32 val = 0; > > + struct drm_display_mode *mode; > > + > > + mode = &bridge->encoder->crtc->state->adjusted_mode; > > + > > + hbpr = 0; > > + hpw = mode->hsync_end - mode->hsync_start; > > + vbpr = 0; > > + vpw = mode->vsync_end - mode->vsync_start; > > + > > + htime1 = (hbpr << 16) + hpw; > > + vtime1 = (vbpr << 16) + vpw; > > + > > + hfpr = mode->hsync_start - mode->hdisplay; > > + hsize = mode->hdisplay; > > + vfpr = mode->vsync_start - mode->vdisplay; > > + vsize = mode->vdisplay; > > + > > + htime2 = (hfpr << 16) + hsize; > > + vtime2 = (vfpr << 16) + vsize; > > + > > + ret = regmap_read(tc->regmap, IDREG, &tc->rev); > > + if (ret) { > > + dev_err(tc->dev, "can not read device ID: %d\n", ret); > > + return; > > + } > > + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev); > > + > > + d2l_write(tc, SYSRST, 0x000000FF); > > + mdelay(30); > > + > > + ret = regmap_register_patch(tc->regmap, > > + tc_fixed_registers, > > + ARRAY_SIZE(tc_fixed_registers)); > > + if (ret) > > + return; > > + > > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; > > + d2l_write(tc, PPI_LANEENABLE, val); > > + d2l_write(tc, DSI_LANEENABLE, val); > > + > > + d2l_write(tc, PPI_STARTPPI, 0x00000001); > > + d2l_write(tc, DSI_STARTDSI, 0x00000001); > > + > > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value Any suggestion how to set dynamic value for Vsyncdelay? > > + > > + if (tc->connector.display_info.bpc == 8) {/* RGB888 */ > > + val |= TC358775_VPCTRL_OPXLFMT(1); > > + d2l_write(tc, VPCTRL, val); > > + } else { /* RGB666 */ > > + val |= TC358775_VPCTRL_MSF(1); > > + d2l_write(tc, VPCTRL, val); > > + } > > + > > + d2l_write(tc, HTIM1, htime1); > > + d2l_write(tc, VTIM1, vtime1); > > + d2l_write(tc, HTIM2, htime2); > > + d2l_write(tc, VTIM2, vtime2); > > + > > + d2l_write(tc, VFUEN, 0x00000001); > > + d2l_write(tc, SYSRST, 0x00000004); > > + d2l_write(tc, LVPHY0, 0x00040006); > > + > > + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */ > > + ret = regmap_register_patch > > + (tc->regmap, > > + tc_vesa_data_format_registers, > > + ARRAY_SIZE(tc_vesa_data_format_registers)); > > + if (ret) > > + return; > > + } > > + > > + d2l_write(tc, VFUEN, 0x00000001); > > + > > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; > > + if (tc->dual_link) > > + val |= TC358775_LVCFG_LVDLINK(1); > > + > > + d2l_write(tc, LVCFG, val); > > + > > + drm_panel_enable(tc->panel); > > +} > > + > > +static int tc_connector_get_modes(struct drm_connector *connector) > > +{ > > + struct tc_data *tc = connector_to_tc(connector); > > + struct edid *edid; > > + unsigned int count; > > + > > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { > > + count = tc->panel->funcs->get_modes(tc->panel, connector); > > + if (count > 0) > > + return count; > > + } > > + > > + edid = drm_get_edid(connector, tc->i2c->adapter); > > + if (!edid) > > + return 0; > > + > > + drm_connector_update_edid_property(connector, edid); > > + count = drm_add_edid_modes(connector, edid); > > + kfree(edid); > > + > > + return count; > > +} > > + > > +static int tc_connector_mode_valid(struct drm_connector *connector, > > + struct drm_display_mode *mode) > > +{ > > + struct tc_data *tc = connector_to_tc(connector); > > + > > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ > > + if ((mode->clock > 135000 && tc->dual_link == 0) || > > + (mode->clock > 270000 && tc->dual_link == 1)) > > + return MODE_CLOCK_HIGH; > > + > > + return MODE_OK; > > +} > > + > > +static struct drm_encoder * > > +tc_connector_best_encoder(struct drm_connector *connector) > > +{ > > + struct tc_data *tc = connector_to_tc(connector); > > + > > + return tc->bridge.encoder; > > +} > > + > > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { > > + .get_modes = tc_connector_get_modes, > > + .mode_valid = tc_connector_mode_valid, > > + .best_encoder = tc_connector_best_encoder, > > +}; > > + > > +static const struct drm_connector_funcs tc_connector_funcs = { > > + .fill_modes = drm_helper_probe_single_connector_modes, > > + .destroy = drm_connector_cleanup, > > + .reset = drm_atomic_helper_connector_reset, > > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > > +}; > > + > > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) > > +{ > > + u32 num_lanes; > > + u8 dual_link, data_format; > > + > > + of_property_read_u8(np, "tc,dual-link", &dual_link); > > + of_property_read_u8(np, "tc,data-format", &data_format); > > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); > > + > > + if (num_lanes < 1 || num_lanes > 4) > > + return -EINVAL; > > + > > + tc->num_dsi_lanes = num_lanes; > > + tc->dual_link = dual_link; > > + tc->data_format = data_format; > > + > > + tc->host_node = of_graph_get_remote_node(np, 0, 0); > > + if (!tc->host_node) > > + return -ENODEV; > > + > > + of_node_put(tc->host_node); > > + > > + return 0; > > +} > > + > > +int tc358775_attach_dsi(struct tc_data *tc) > > +{ > > + struct device *dev = &tc->i2c->dev; > > + struct mipi_dsi_host *host; > > + struct mipi_dsi_device *dsi; > > + int ret = 0; > > + const struct mipi_dsi_device_info info = { .type = "tc358775", > > + .channel = 0, > > + .node = NULL, > > + }; > > + > > + host = of_find_mipi_dsi_host_by_node(tc->host_node); > > + if (!host) { > > + dev_err(dev, "failed to find dsi host\n"); > > + return -EPROBE_DEFER; > > + } > > + > > + dsi = mipi_dsi_device_register_full(host, &info); > > + if (IS_ERR(dsi)) { > > + dev_err(dev, "failed to create dsi device\n"); > > + ret = PTR_ERR(dsi); > > + goto err_dsi_device; > > + } > > + > > + tc->dsi = dsi; > > + > > + dsi->lanes = tc->num_dsi_lanes; > > + dsi->format = MIPI_DSI_FMT_RGB888; > > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; > > + > > + ret = mipi_dsi_attach(dsi); > > + if (ret < 0) { > > + dev_err(dev, "failed to attach dsi to host\n"); > > + goto err_dsi_attach; > > + } > > + > > + return 0; > > + > > +err_dsi_attach: > > + mipi_dsi_device_unregister(dsi); > > +err_dsi_device: > > + return ret; > > +} > > + > > +static int tc_bridge_attach(struct drm_bridge *bridge) > > +{ > > + struct tc_data *tc = bridge_to_tc(bridge); > > + struct drm_device *drm = bridge->dev; > > + int ret; > > + > > + /* Create LVDS connector */ > > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); > > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, > > + DRM_MODE_CONNECTOR_LVDS); > > + if (ret) > > + return ret; > > + > > + if (tc->panel) > > + drm_panel_attach(tc->panel, &tc->connector); > > + > > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); > > + > > + ret = tc358775_attach_dsi(tc); > > > Ignored retval. > > > > + > > + return 0; > > +} > > + > > +static const struct drm_bridge_funcs tc_bridge_funcs = { > > + .attach = tc_bridge_attach, > > + .pre_enable = tc_bridge_pre_enable, > > + .enable = tc_bridge_enable, > > + .disable = tc_bridge_disable, > > + .post_disable = tc_bridge_post_disable, > > +}; > > + > > +static const struct regmap_config tc_regmap_config = { > > + .name = "tc358775", > > + .reg_bits = 16, > > + .val_bits = 32, > > + .reg_stride = 4, > > + .max_register = 0x05A8, > > + .cache_type = REGCACHE_RBTREE, > > + .reg_format_endian = REGMAP_ENDIAN_BIG, > > + .val_format_endian = REGMAP_ENDIAN_LITTLE, > > +}; > > + > > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) > > +{ > > + struct device *dev = &client->dev; > > + struct tc_data *tc; > > + int ret; > > + unsigned int i; > > + > > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); > > + if (!tc) > > + return -ENOMEM; > > + > > + tc->dev = dev; > > + tc->i2c = client; > > + tc->status = connector_status_connected; > > + > > + /* port@1 is the output port */ > > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); > > + if (ret && ret != -ENODEV) > > + return ret; > > + > > + ret = tc358775_parse_dt(dev->of_node, tc); > > + if (ret) > > + return ret; > > + > > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) > > + tc->supplies[i].supply = regulator_names[i]; > > + > > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), > > + tc->supplies); > > + if (ret < 0) > > + dev_err(dev, "failed to init regulator, ret=%d\n", ret); > > + > > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); > > + if (IS_ERR(tc->stby_gpio)) { > > + ret = PTR_ERR(tc->stby_gpio); > > + dev_err(dev, "cannot get stby-gpio %d\n", ret); > > + return ret; > > + } > > + > > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > > + if (IS_ERR(tc->reset_gpio)) { > > + ret = PTR_ERR(tc->reset_gpio); > > + dev_err(dev, "cannot get reset-gpios %d\n", ret); > > + return ret; > > + } > > + > > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); > > + if (IS_ERR(tc->regmap)) { > > + ret = PTR_ERR(tc->regmap); > > + dev_err(dev, "Failed to initialize regmap: %d\n", ret); > > + return ret; > > + } > > + > > + tc->bridge.funcs = &tc_bridge_funcs; > > + tc->bridge.of_node = dev->of_node; > > + drm_bridge_add(&tc->bridge); > > + > > + i2c_set_clientdata(client, tc); > > + > > + return 0; > > +} > > + > > +static int tc_remove(struct i2c_client *client) > > +{ > > + struct tc_data *tc = i2c_get_clientdata(client); > > + > > + drm_bridge_remove(&tc->bridge); > > + > > + return 0; > > +} > > + > > +static const struct i2c_device_id tc358775_i2c_ids[] = { > > + { "tc358775", 0 }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); > > + > > +static const struct of_device_id tc358775_of_ids[] = { > > + { .compatible = "toshiba,tc358775", }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(of, tc358775_of_ids); > > + > > +static struct i2c_driver tc358775_driver = { > > + .driver = { > > + .name = "tc358775", > > + .of_match_table = tc358775_of_ids, > > + }, > > + .id_table = tc358775_i2c_ids, > > + .probe = tc_probe, > > + .remove = tc_remove, > > +}; > > +module_i2c_driver(tc358775_driver); > > + > > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); > > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); > > > maybe better: > > tc358775 DSI/LVDS bridge driver > > > Regards > Andrzej > > > +MODULE_LICENSE("GPL v2"); > > -- regards, vinaysimha _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hi Vinay, Thank you for the patch. On Fri, Mar 06, 2020 at 06:06:36PM +0530, Vinay Simha B N wrote: > hi andrzej, > > I had a doubt In the tc358764 driver,VP_CTRL, VP_CTRL_VSDELAY(15) is > hardcoded to 15, but this has to be dynamic based on the resolution of > panel used? > > Please see the reply inline. > > On Tue, Mar 3, 2020 at 8:39 PM Andrzej Hajda <a.hajda@samsung.com> wrote: > > On 27.02.2020 15:03, Vinay Simha BN wrote: > > > dsi2lvds tc358775 bridge driver added > > > Tested in apq8016, ifc6309 board and panel > > > auo,b101xtn01 > > > > Just FYI, there exists already TC358764/5 driver for similar hw, but > > controlled via DSI bus. > > There is not much difference between these two chips, but still the > dsi read access for 775 does not works. > TC358764/5 - 800Mbps per lane, 3.2Gbps > TC358775 - 1Gbps per lane, 4Gbps. > > tc358775 chip details - > https://download.t-firefly.com/product/RK3399/Docs/Chip%20Specifications/TC358774XBG_75XBG_V1%204nm.pdf > I am able to configure the tc358775 chip by i2c, but from dsi it fails > i tried accessing the tc358775 chip by dsi using apq8016-qcom , but it > fails to read the chip id itself. > > Please suggest if you any inputs for this issue. > > https://github.com/vinaysimhabn/kernel-msm/commits/5.6.0-rc3-dsi2lvds-dsi > > [ 4.582405] tc358764 1a98000.dsi.0: read: 1408, addr: 0 > [ 4.582426] tc358764 1a98000.dsi.0: ID: 0x0 > [ 4.582451] tc358764 1a98000.dsi.0: error initializing bridge (-22) > > [ 4.796220] dsi_cmds2buf_tx: cmd dma tx failed, type=0x24, data0=0x80, len=4 > [ 4.796244] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > [ 4.796266] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > [ 4.796288] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > [ 4.796310] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > [ 4.796319] msm_dsi_host_cmd_rx:Invalid response cmd > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > > --- > > > .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++ > > > > Bindings should be in separate patch and in yaml format. > > > > > drivers/gpu/drm/bridge/Kconfig | 10 + > > > drivers/gpu/drm/bridge/Makefile | 1 + > > > drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++ > > > 4 files changed, 804 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > create mode 100644 drivers/gpu/drm/bridge/tc358775.c > > > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > new file mode 100644 > > > index 0000000..c4c364d > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > @@ -0,0 +1,106 @@ > > > +Toshiba TC358775 DSI to LVDS bridge bindings > > > + > > > +Required properties: > > > + - compatible: "toshiba,tc358775" > > > + - reg: i2c address of the bridge, 0x0f > > > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should > > > + be one of 1, 2, 3 or 4. > > > + - tc, dual-link : To configure the LVDS transmitter either > > > + as single-link or dual-link. > > > + - tc, data-format: To configure the data formats > > > + 0 for VESA standard, 1 for JEIDA standard > > > > IMO, three properties above should be received from downstream device in > > runtime, not hardcoded into DT, however I am not sure if frameworks > > support it. I assume Andrzej meant upstream device for the tc,dsi-lanes property. This should be exposed through the data-lanes property as described in media/video-interface.txt. The tc,dual-link property should be replaced by exposing two port nodes, one for each link, and connecting them appropriately. See display/bridge/thine,thc63lvd1024.txt for an example of DT bindings on the LVDS receiver side, and drivers/gpu/drm/rcar-du/rcar_lvds.c for an example implementation on the LVDS transmitter side. The tc,data-format property should be replaced by the data-mapping property on the downstream LVDS device (see display/panel/lvds.yaml) and queried at runtime. > > > + - vdd-supply: 1.2V LVDS Power Supply > > > + - vddio-supply: 1.8V IO Power Supply > > > + - stby-gpios: Standby pin, Low active > > > + - reset-gpios: Hardware reset, Low active > > > + > > > +Required nodes: > > > + > > > +The TC358775 has two ports. Their connections are modelled using the OF > > > +graph bindings specified in Documentation/devicetree/bindings/graph.txt. > > > + > > > +- Video port 0 for the DSI input. The remote endpoint phandle should be a > > > + reference to a valid mipi_dsi_host device node. > > > +- Video port 1 for the LVDS output. > > > + > > > +Example: > > > + > > > + i2c@78b8000 { > > > + /* On High speed expansion */ > > > + label = "HS-I2C2"; > > > + status = "okay"; > > > + > > > + tc_bridge: bridge@f { > > > + status = "okay"; > > > + > > > + compatible = "toshiba,tc358775"; > > > + reg = <0x0f>; > > > + > > > + tc,dsi-lanes = <4>; > > > + tc,dual-link = <0>; > > > + tc,data-format = <1>; > > > + > > > + vdd-supply = <&pm8916_l2>; > > > + vddio-supply = <&pm8916_l6>; > > > + > > > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > > > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > > > + > > > + ports { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + port@0 { > > > + reg = <0>; > > > + d2l_in: endpoint { > > > + remote-endpoint = <&dsi0_out>; > > > + }; > > > + }; > > > + > > > + port@1 { > > > + reg = <1>; > > > + d2l_out: endpoint { > > > + remote-endpoint = <&panel_in>; > > > + }; > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > + panel: auo,b101xtn01 { > > > + status = "okay"; > > > + compatible = "auo,b101xtn01"; > > > + power-supply = <&pm8916_l14>; > > > + > > > + port { > > > + panel_in: endpoint { > > > + remote-endpoint = <&d2l_out>; > > > + }; > > > + }; > > > + }; > > > + > > > + mdss@1a00000 { > > > + status = "okay"; > > > + > > > + mdp@1a01000 { > > > + status = "okay"; > > > + }; > > > + > > > + dsi@1a98000 { > > > + status = "okay"; > > > + .. > > > + ports { > > > + port@1 { > > > + dsi0_out: endpoint { > > > + remote-endpoint = <&d2l_in>; > > > + data-lanes = <0 1 2 3>; > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > + dsi-phy@1a98300 { > > > + status = "okay"; > > > + .. > > > + }; > > > + }; > > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig > > > index 8397bf7..d5528fa 100644 > > > --- a/drivers/gpu/drm/bridge/Kconfig > > > +++ b/drivers/gpu/drm/bridge/Kconfig > > > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 > > > ---help--- > > > Toshiba TC358767 eDP bridge chip driver. > > > > > > +config DRM_TOSHIBA_TC358775 > > > + tristate "Toshiba TC358775 LVDS bridge" > > > + depends on OF > > > + select DRM_KMS_HELPER > > > + select REGMAP_I2C > > > + select DRM_PANEL > > > + select DRM_MIPI_DSI > > > + ---help--- > > > + Toshiba TC358775 LVDS bridge chip driver. > > > + > > > config DRM_TI_TFP410 > > > tristate "TI TFP410 DVI/HDMI bridge" > > > depends on OF > > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile > > > index 1eb5376..9b2c512 100644 > > > --- a/drivers/gpu/drm/bridge/Makefile > > > +++ b/drivers/gpu/drm/bridge/Makefile > > > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o > > > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o > > > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o > > > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o > > > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o > > > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ > > > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o > > > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o > > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c > > > new file mode 100644 > > > index 0000000..3db0f49 > > > --- /dev/null > > > +++ b/drivers/gpu/drm/bridge/tc358775.c > > > @@ -0,0 +1,687 @@ > > > +// SPDX-License-Identifier: GPL-2.0 > > > +/* > > > + * tc358775 DSI to LVDS bridge driver > > > + * > > > + * Copyright (C) 2020 InforceComputing > > > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> > > > + * > > > + * This program is free software; you can redistribute it and/or modify > > > + * it under the terms of the GNU General Public License as published by > > > + * the Free Software Foundation; either version 2 of the License, or > > > + * (at your option) any later version. > > > + * > > > + * This program is distributed in the hope that it will be useful, > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > + * GNU General Public License for more details. > > > > You can drop these statements, SPDX identifier is enough. > > > > > + */ > > > + > > > +/* #define DEBUG */ > > > +/* #define TC358775_DEBUG */ > > > > Please remove these development leftovers. > > > > > +#include <linux/clk.h> > > > +#include <linux/device.h> > > > +#include <linux/gpio/consumer.h> > > > +#include <linux/i2c.h> > > > +#include <linux/kernel.h> > > > +#include <linux/module.h> > > > +#include <linux/regmap.h> > > > +#include <linux/slab.h> > > > +#include <linux/regulator/consumer.h> > > Alphabetic order. > > > + > > > +#include <drm/drm_mipi_dsi.h> > > > +#include <drm/drm_atomic_helper.h> > > > +#include <drm/drm_crtc_helper.h> > > > +#include <drm/drm_dp_helper.h> > > > +#include <drm/drm_of.h> > > > +#include <drm/drm_panel.h> > > > +#include <drm/drm_bridge.h> > > > +#include <drm/drm_probe_helper.h> > > ditto > > > + > > > +/* Registers */ > > > + > > > +/* DSI D-PHY Layer Registers */ > > > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ > > > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ > > > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ > > > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ > > > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ > > > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ > > > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ > > > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ > > > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ > > > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ > > > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ > > > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ > > > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ > > > + > > > +/* DSI PPI Layer Registers */ > > > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ > > > +#define PPI_BUSYPPI 0x0108 > > > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ > > > +#define PPI_LPTXTIMECNT 0x0114 > > > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ > > > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ > > > + > > > +/* Analog timer function enable */ > > > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ > > > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ > > > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ > > > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ > > > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ > > > +#define PPI_D0S_CLRSIPOCOUNT 0x0164 > > > + > > > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ > > > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ > > > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ > > > + > > > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ > > > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ > > > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ > > > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ > > > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ > > > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ > > > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ > > > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ > > > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ > > > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ > > > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ > > > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ > > > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ > > > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ > > > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ > > > + > > > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ > > > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ > > > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ > > > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ > > > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ > > > +#define DSI_BUSYDSI 0x0208 > > > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ > > > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ > > > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ > > > + > > > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ > > > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ > > > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ > > > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ > > > + > > > +#define DSIERRCNT 0x0300 /* DSI Error Count */ > > > +#define APLCTRL 0x0400 /* Application Layer Control */ > > > +#define RDPKTLN 0x0404 /* Command Read Packet Length */ > > > + > > > +#define VPCTRL 0x0450 /* Video Path Control */ > > > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ > > > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ > > > +#define VTIM1 0x045C /* Vertical Timing Control 1 */ > > > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ > > > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ > > > + > > > +/* Mux Input Select for LVDS LINK Input */ > > > +#define LVMX0003 0x0480 /* Bit 0 to 3 */ > > > +#define LVMX0407 0x0484 /* Bit 4 to 7 */ > > > +#define LVMX0811 0x0488 /* Bit 8 to 11 */ > > > +#define LVMX1215 0x048C /* Bit 12 to 15 */ > > > +#define LVMX1619 0x0490 /* Bit 16 to 19 */ > > > +#define LVMX2023 0x0494 /* Bit 20 to 23 */ > > > +#define LVMX2427 0x0498 /* Bit 24 to 27 */ > > > + > > > +#define LVCFG 0x049C /* LVDS Configuration */ > > > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ > > > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ > > > +#define SYSSTAT 0x0500 /* System Status */ > > > +#define SYSRST 0x0504 /* System Reset */ > > > +/* GPIO Registers */ > > > +#define GPIOC 0x0520 /* GPIO Control */ > > > +#define GPIOO 0x0524 /* GPIO Output */ > > > +#define GPIOI 0x0528 /* GPIO Input */ > > > + > > > +/* I2C Registers */ > > > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ > > > +#define I2CMADDR 0x0544 /* I2C Master Addressing */ > > > +#define WDATAQ 0x0548 /* Write Data Queue */ > > > +#define RDATAQ 0x054C /* Read Data Queue */ > > > + > > > +/* Chip ID and Revision ID Register */ > > > +#define IDREG 0x0580 > > > + > > > +#define TC358775XBG_ID 0x00007500 > > > + > > > +/* Debug Registers */ > > > +#define DEBUG00 0x05A0 /* Debug */ > > > +#define DEBUG01 0x05A4 /* LVDS Data */ > > > + > > > +#define DSI_CLEN_BIT BIT(0) > > > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ > > > +#define LVCFG_LVEN_BIT BIT(0) > > > + > > > +#define L0EN BIT(1) > > > + > > > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 > > > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 > > > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val) > > > > > > Use u32 here and below, unit32_t is mainly for userspace interactions. > > > > > > > +{ > > > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & > > > + TC358775_VPCTRL_VSDELAY__MASK; > > > +} > > > + > > > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 > > > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 > > > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val) > > > +{ > > > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & > > > + TC358775_VPCTRL_OPXLFMT__MASK; > > > +} > > > + > > > +#define TC358775_VPCTRL_MSF__MASK 0x00000001 > > > +#define TC358775_VPCTRL_MSF__SHIFT 0 > > > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val) > > > +{ > > > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & > > > + TC358775_VPCTRL_MSF__MASK; > > > +} > > > + > > > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 > > > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 > > > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val) > > > +{ > > > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & > > > + TC358775_LVCFG_PCLKDIV__MASK; > > > +} > > > + > > > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 > > > +#define TC358775_LVCFG_LVDLINK__SHIFT 0 > > > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val) > > > +{ > > > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & > > > + TC358775_LVCFG_LVDLINK__MASK; > > > +} > > > + > > > +static const struct reg_sequence tc_fixed_registers[] = { > > > + { 0x013C, 0x00040006 }, > > > + { 0x0114, 0x00000004 }, > > > + { 0x0164, 0x00000003 }, > > > + { 0x0168, 0x00000003 }, > > > + { 0x016C, 0x00000003 }, > > > + { 0x0170, 0x00000003 }, > > > > use macros instead of magic numbers. > > > > > +}; > > > + > > > +static const struct reg_sequence tc_vesa_data_format_registers[] = { > > > + { 0x0480, 0x03020100 }, > > > + { 0x0484, 0x08050704 }, > > > + { 0x0488, 0x0F0E0A09 }, > > > + { 0x048C, 0x100D0C0B }, > > > + { 0x0490, 0x12111716 }, > > > + { 0x0494, 0x1B151413 }, > > > + { 0x0498, 0x061A1918 }, > > ditto > > > +}; > > > + > > > +static const char * const regulator_names[] = { > > > + "vdd", > > > + "vddio" > > > +}; > > > + > > > +struct tc_data { > > > + struct i2c_client *i2c; > > > + > > > + struct device *dev; > > > + struct regmap *regmap; > > > + > > > + struct drm_bridge bridge; > > > + struct drm_connector connector; > > > + struct drm_panel *panel; > > > + > > > + enum drm_connector_status status; > > unused field > > > + struct device_node *host_node; > > > + struct mipi_dsi_device *dsi; > > > + u8 num_dsi_lanes; > > > + > > > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; > > > + struct gpio_desc *reset_gpio; > > > + struct gpio_desc *stby_gpio; > > > + u32 rev; > > > + u8 dual_link; /* single-link or dual-link */ > > > + u8 data_format; /* VESA or JEIDA */ > > > +}; > > > + > > > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) > > > +{ > > > + return container_of(b, struct tc_data, bridge); > > > +} > > > + > > > +static inline struct tc_data *connector_to_tc(struct drm_connector *c) > > > +{ > > > + return container_of(c, struct tc_data, connector); > > > +} > > > + > > > +static void tc_bridge_pre_enable(struct drm_bridge *bridge) > > > +{ > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > + struct device *dev = &tc->dsi->dev; > > > + int ret; > > > + > > > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); > > > + if (ret < 0) { > > > + dev_err(dev, "regulator enable failed, %d\n", ret); > > > + return; > > > + } > > > + mdelay(10); You should consider usleep_range() instead of mdelay() for large delays. > > > + > > > + gpiod_set_value(tc->stby_gpio, 0); > > > + mdelay(10); > > > + > > > + gpiod_set_value(tc->reset_gpio, 0); > > > + ndelay(50); > > > + > > > + drm_panel_prepare(tc->panel); > > > +} > > > + > > > +static void tc_bridge_disable(struct drm_bridge *bridge) > > > +{ > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > + struct device *dev = &tc->dsi->dev; > > > + int ret; > > > + > > > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); > > > + if (ret < 0) > > > + dev_err(dev, "regulator disable failed, %d\n", ret); > > > + mdelay(10); > > > + > > > + gpiod_set_value(tc->stby_gpio, 1); > > > + mdelay(10); > > > + > > > + gpiod_set_value(tc->reset_gpio, 1); > > > + ndelay(50); > > > + > > > + drm_panel_disable(tc->panel); > > > > I suspect the order should be different - ie reverse to the one pre_enable. > > > > Moreover since it reverts pre_enable it should be put into post_disable > > (except drm_panel_disable). > > > > > +} > > > + > > > +static void tc_bridge_post_disable(struct drm_bridge *bridge) > > > +{ > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > + > > > + drm_panel_unprepare(tc->panel); > > > +} > > > + > > > +#ifdef TC358775_DEBUG > > > +static u32 d2l_read(struct tc_data *tc, u16 reg) > > > +{ > > > + int ret; > > > + u32 data; > > > + > > > + ret = regmap_bulk_read(tc->regmap, reg, &data, 1); > > > + if (ret) > > > + return ret; > > > + > > > + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data); > > > + > > > + return data; > > > +} > > > +#endif > > > > I guess this leftover can be removed as well. > > > > > + > > > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) > > > +{ > > > + int ret = 0; > > > + > > > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); > > > + > > > +#ifdef TC358775_DEBUG > > > + d2l_read(tc, reg); > > > +#endif > > > + return ret; > > > +} > > > + > > > +static void tc_bridge_enable(struct drm_bridge *bridge) > > > +{ > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > + int ret; > > > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; > > > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; > > > + u32 val = 0; > > > + struct drm_display_mode *mode; > > > + > > > + mode = &bridge->encoder->crtc->state->adjusted_mode; > > > + > > > + hbpr = 0; > > > + hpw = mode->hsync_end - mode->hsync_start; > > > + vbpr = 0; > > > + vpw = mode->vsync_end - mode->vsync_start; > > > + > > > + htime1 = (hbpr << 16) + hpw; > > > + vtime1 = (vbpr << 16) + vpw; > > > + > > > + hfpr = mode->hsync_start - mode->hdisplay; > > > + hsize = mode->hdisplay; > > > + vfpr = mode->vsync_start - mode->vdisplay; > > > + vsize = mode->vdisplay; > > > + > > > + htime2 = (hfpr << 16) + hsize; > > > + vtime2 = (vfpr << 16) + vsize; > > > + > > > + ret = regmap_read(tc->regmap, IDREG, &tc->rev); > > > + if (ret) { > > > + dev_err(tc->dev, "can not read device ID: %d\n", ret); > > > + return; > > > + } > > > + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev); > > > + > > > + d2l_write(tc, SYSRST, 0x000000FF); > > > + mdelay(30); > > > + > > > + ret = regmap_register_patch(tc->regmap, > > > + tc_fixed_registers, > > > + ARRAY_SIZE(tc_fixed_registers)); > > > + if (ret) > > > + return; > > > + > > > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; > > > + d2l_write(tc, PPI_LANEENABLE, val); > > > + d2l_write(tc, DSI_LANEENABLE, val); > > > + > > > + d2l_write(tc, PPI_STARTPPI, 0x00000001); > > > + d2l_write(tc, DSI_STARTDSI, 0x00000001); > > > + > > > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value > > Any suggestion how to set dynamic value for Vsyncdelay? > > > > + > > > + if (tc->connector.display_info.bpc == 8) {/* RGB888 */ > > > + val |= TC358775_VPCTRL_OPXLFMT(1); > > > + d2l_write(tc, VPCTRL, val); > > > + } else { /* RGB666 */ > > > + val |= TC358775_VPCTRL_MSF(1); > > > + d2l_write(tc, VPCTRL, val); > > > + } > > > + > > > + d2l_write(tc, HTIM1, htime1); > > > + d2l_write(tc, VTIM1, vtime1); > > > + d2l_write(tc, HTIM2, htime2); > > > + d2l_write(tc, VTIM2, vtime2); > > > + > > > + d2l_write(tc, VFUEN, 0x00000001); > > > + d2l_write(tc, SYSRST, 0x00000004); > > > + d2l_write(tc, LVPHY0, 0x00040006); > > > + > > > + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */ > > > + ret = regmap_register_patch > > > + (tc->regmap, > > > + tc_vesa_data_format_registers, > > > + ARRAY_SIZE(tc_vesa_data_format_registers)); > > > + if (ret) > > > + return; > > > + } > > > + > > > + d2l_write(tc, VFUEN, 0x00000001); > > > + > > > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; > > > + if (tc->dual_link) > > > + val |= TC358775_LVCFG_LVDLINK(1); > > > + > > > + d2l_write(tc, LVCFG, val); > > > + > > > + drm_panel_enable(tc->panel); > > > +} > > > + > > > +static int tc_connector_get_modes(struct drm_connector *connector) > > > +{ > > > + struct tc_data *tc = connector_to_tc(connector); > > > + struct edid *edid; > > > + unsigned int count; > > > + > > > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { > > > + count = tc->panel->funcs->get_modes(tc->panel, connector); > > > + if (count > 0) > > > + return count; > > > + } > > > + > > > + edid = drm_get_edid(connector, tc->i2c->adapter); > > > + if (!edid) > > > + return 0; > > > + > > > + drm_connector_update_edid_property(connector, edid); > > > + count = drm_add_edid_modes(connector, edid); > > > + kfree(edid); > > > + > > > + return count; > > > +} > > > + > > > +static int tc_connector_mode_valid(struct drm_connector *connector, > > > + struct drm_display_mode *mode) > > > +{ > > > + struct tc_data *tc = connector_to_tc(connector); > > > + > > > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ > > > + if ((mode->clock > 135000 && tc->dual_link == 0) || > > > + (mode->clock > 270000 && tc->dual_link == 1)) > > > + return MODE_CLOCK_HIGH; > > > + > > > + return MODE_OK; > > > +} This should be replaced by the bridge .mode_valid() operation, as it's related to the bridge, not the connector. > > > + > > > +static struct drm_encoder * > > > +tc_connector_best_encoder(struct drm_connector *connector) > > > +{ > > > + struct tc_data *tc = connector_to_tc(connector); > > > + > > > + return tc->bridge.encoder; > > > +} > > > + > > > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { > > > + .get_modes = tc_connector_get_modes, > > > + .mode_valid = tc_connector_mode_valid, > > > + .best_encoder = tc_connector_best_encoder, > > > +}; > > > + > > > +static const struct drm_connector_funcs tc_connector_funcs = { > > > + .fill_modes = drm_helper_probe_single_connector_modes, > > > + .destroy = drm_connector_cleanup, > > > + .reset = drm_atomic_helper_connector_reset, > > > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > > > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > > > +}; > > > + > > > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) > > > +{ > > > + u32 num_lanes; > > > + u8 dual_link, data_format; > > > + > > > + of_property_read_u8(np, "tc,dual-link", &dual_link); > > > + of_property_read_u8(np, "tc,data-format", &data_format); > > > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); > > > + > > > + if (num_lanes < 1 || num_lanes > 4) > > > + return -EINVAL; > > > + > > > + tc->num_dsi_lanes = num_lanes; > > > + tc->dual_link = dual_link; > > > + tc->data_format = data_format; > > > + > > > + tc->host_node = of_graph_get_remote_node(np, 0, 0); > > > + if (!tc->host_node) > > > + return -ENODEV; > > > + > > > + of_node_put(tc->host_node); > > > + > > > + return 0; > > > +} > > > + > > > +int tc358775_attach_dsi(struct tc_data *tc) > > > +{ > > > + struct device *dev = &tc->i2c->dev; > > > + struct mipi_dsi_host *host; > > > + struct mipi_dsi_device *dsi; > > > + int ret = 0; > > > + const struct mipi_dsi_device_info info = { .type = "tc358775", > > > + .channel = 0, > > > + .node = NULL, > > > + }; > > > + > > > + host = of_find_mipi_dsi_host_by_node(tc->host_node); > > > + if (!host) { > > > + dev_err(dev, "failed to find dsi host\n"); > > > + return -EPROBE_DEFER; > > > + } > > > + > > > + dsi = mipi_dsi_device_register_full(host, &info); > > > + if (IS_ERR(dsi)) { > > > + dev_err(dev, "failed to create dsi device\n"); > > > + ret = PTR_ERR(dsi); > > > + goto err_dsi_device; > > > + } > > > + > > > + tc->dsi = dsi; > > > + > > > + dsi->lanes = tc->num_dsi_lanes; > > > + dsi->format = MIPI_DSI_FMT_RGB888; > > > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; > > > + > > > + ret = mipi_dsi_attach(dsi); > > > + if (ret < 0) { > > > + dev_err(dev, "failed to attach dsi to host\n"); > > > + goto err_dsi_attach; > > > + } > > > + > > > + return 0; > > > + > > > +err_dsi_attach: > > > + mipi_dsi_device_unregister(dsi); > > > +err_dsi_device: > > > + return ret; > > > +} > > > + > > > +static int tc_bridge_attach(struct drm_bridge *bridge) > > > +{ > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > + struct drm_device *drm = bridge->dev; > > > + int ret; > > > + > > > + /* Create LVDS connector */ > > > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); > > > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, > > > + DRM_MODE_CONNECTOR_LVDS); > > > + if (ret) > > > + return ret; > > > + > > > + if (tc->panel) > > > + drm_panel_attach(tc->panel, &tc->connector); > > > + > > > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); > > > + > > > + ret = tc358775_attach_dsi(tc); > > > > Ignored retval. > > > > > + > > > + return 0; > > > +} > > > + > > > +static const struct drm_bridge_funcs tc_bridge_funcs = { > > > + .attach = tc_bridge_attach, > > > + .pre_enable = tc_bridge_pre_enable, > > > + .enable = tc_bridge_enable, > > > + .disable = tc_bridge_disable, > > > + .post_disable = tc_bridge_post_disable, > > > +}; > > > + > > > +static const struct regmap_config tc_regmap_config = { > > > + .name = "tc358775", > > > + .reg_bits = 16, > > > + .val_bits = 32, > > > + .reg_stride = 4, > > > + .max_register = 0x05A8, > > > + .cache_type = REGCACHE_RBTREE, > > > + .reg_format_endian = REGMAP_ENDIAN_BIG, > > > + .val_format_endian = REGMAP_ENDIAN_LITTLE, > > > +}; > > > + > > > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) > > > +{ > > > + struct device *dev = &client->dev; > > > + struct tc_data *tc; > > > + int ret; > > > + unsigned int i; > > > + > > > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); > > > + if (!tc) > > > + return -ENOMEM; > > > + > > > + tc->dev = dev; > > > + tc->i2c = client; > > > + tc->status = connector_status_connected; > > > + > > > + /* port@1 is the output port */ > > > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); > > > + if (ret && ret != -ENODEV) > > > + return ret; You should support cases where the next device is a bridge. I recommand wrapping the panel in a drm_panel_bridge with drm_panel_bridge_add(), and then handling the next component as a bridge in all code paths. This will allow removing manual enable/disable of panels above, as bridge chaining is handled automatically. drm_panel_bridge creates a drm_connector, so you can drop your manual connector implementation here, simplifying the code. > > > + > > > + ret = tc358775_parse_dt(dev->of_node, tc); > > > + if (ret) > > > + return ret; > > > + > > > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) > > > + tc->supplies[i].supply = regulator_names[i]; > > > + > > > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), > > > + tc->supplies); > > > + if (ret < 0) > > > + dev_err(dev, "failed to init regulator, ret=%d\n", ret); > > > + > > > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); > > > + if (IS_ERR(tc->stby_gpio)) { > > > + ret = PTR_ERR(tc->stby_gpio); > > > + dev_err(dev, "cannot get stby-gpio %d\n", ret); > > > + return ret; > > > + } > > > + > > > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > > > + if (IS_ERR(tc->reset_gpio)) { > > > + ret = PTR_ERR(tc->reset_gpio); > > > + dev_err(dev, "cannot get reset-gpios %d\n", ret); > > > + return ret; > > > + } > > > + > > > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); > > > + if (IS_ERR(tc->regmap)) { > > > + ret = PTR_ERR(tc->regmap); > > > + dev_err(dev, "Failed to initialize regmap: %d\n", ret); > > > + return ret; > > > + } > > > + > > > + tc->bridge.funcs = &tc_bridge_funcs; > > > + tc->bridge.of_node = dev->of_node; > > > + drm_bridge_add(&tc->bridge); > > > + > > > + i2c_set_clientdata(client, tc); > > > + > > > + return 0; > > > +} > > > + > > > +static int tc_remove(struct i2c_client *client) > > > +{ > > > + struct tc_data *tc = i2c_get_clientdata(client); > > > + > > > + drm_bridge_remove(&tc->bridge); > > > + > > > + return 0; > > > +} > > > + > > > +static const struct i2c_device_id tc358775_i2c_ids[] = { > > > + { "tc358775", 0 }, > > > + { } > > > +}; > > > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); > > > + > > > +static const struct of_device_id tc358775_of_ids[] = { > > > + { .compatible = "toshiba,tc358775", }, > > > + { } > > > +}; > > > +MODULE_DEVICE_TABLE(of, tc358775_of_ids); > > > + > > > +static struct i2c_driver tc358775_driver = { > > > + .driver = { > > > + .name = "tc358775", > > > + .of_match_table = tc358775_of_ids, > > > + }, > > > + .id_table = tc358775_i2c_ids, > > > + .probe = tc_probe, > > > + .remove = tc_remove, > > > +}; > > > +module_i2c_driver(tc358775_driver); > > > + > > > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); > > > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); > > > > maybe better: > > > > tc358775 DSI/LVDS bridge driver > > > > > +MODULE_LICENSE("GPL v2"); -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Laurent Pinchart, if we want to set to jeida-18 data mapping, do we need to set DATA3 with "Logic 0" LVI_L0 ? Please see reply inline. On Fri, Mar 6, 2020 at 7:02 PM Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote: > > Hi Vinay, > > Thank you for the patch. > > On Fri, Mar 06, 2020 at 06:06:36PM +0530, Vinay Simha B N wrote: > > hi andrzej, > > > > I had a doubt In the tc358764 driver,VP_CTRL, VP_CTRL_VSDELAY(15) is > > hardcoded to 15, but this has to be dynamic based on the resolution of > > panel used? > > > > Please see the reply inline. > > > > On Tue, Mar 3, 2020 at 8:39 PM Andrzej Hajda <a.hajda@samsung.com> wrote: > > > On 27.02.2020 15:03, Vinay Simha BN wrote: > > > > dsi2lvds tc358775 bridge driver added > > > > Tested in apq8016, ifc6309 board and panel > > > > auo,b101xtn01 > > > > > > Just FYI, there exists already TC358764/5 driver for similar hw, but > > > controlled via DSI bus. > > > > There is not much difference between these two chips, but still the > > dsi read access for 775 does not works. > > TC358764/5 - 800Mbps per lane, 3.2Gbps > > TC358775 - 1Gbps per lane, 4Gbps. > > > > tc358775 chip details - > > https://download.t-firefly.com/product/RK3399/Docs/Chip%20Specifications/TC358774XBG_75XBG_V1%204nm.pdf > > I am able to configure the tc358775 chip by i2c, but from dsi it fails > > i tried accessing the tc358775 chip by dsi using apq8016-qcom , but it > > fails to read the chip id itself. > > > > Please suggest if you any inputs for this issue. > > > > https://github.com/vinaysimhabn/kernel-msm/commits/5.6.0-rc3-dsi2lvds-dsi > > > > [ 4.582405] tc358764 1a98000.dsi.0: read: 1408, addr: 0 > > [ 4.582426] tc358764 1a98000.dsi.0: ID: 0x0 > > [ 4.582451] tc358764 1a98000.dsi.0: error initializing bridge (-22) > > > > [ 4.796220] dsi_cmds2buf_tx: cmd dma tx failed, type=0x24, data0=0x80, len=4 > > [ 4.796244] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > [ 4.796266] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > [ 4.796288] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > [ 4.796310] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > [ 4.796319] msm_dsi_host_cmd_rx:Invalid response cmd > > > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > > > --- > > > > .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++ > > > > > > Bindings should be in separate patch and in yaml format. > > > > > > > drivers/gpu/drm/bridge/Kconfig | 10 + > > > > drivers/gpu/drm/bridge/Makefile | 1 + > > > > drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++ > > > > 4 files changed, 804 insertions(+) > > > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > > create mode 100644 drivers/gpu/drm/bridge/tc358775.c > > > > > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > > new file mode 100644 > > > > index 0000000..c4c364d > > > > --- /dev/null > > > > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > > @@ -0,0 +1,106 @@ > > > > +Toshiba TC358775 DSI to LVDS bridge bindings > > > > + > > > > +Required properties: > > > > + - compatible: "toshiba,tc358775" > > > > + - reg: i2c address of the bridge, 0x0f > > > > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should > > > > + be one of 1, 2, 3 or 4. > > > > + - tc, dual-link : To configure the LVDS transmitter either > > > > + as single-link or dual-link. > > > > + - tc, data-format: To configure the data formats > > > > + 0 for VESA standard, 1 for JEIDA standard > > > > > > IMO, three properties above should be received from downstream device in > > > runtime, not hardcoded into DT, however I am not sure if frameworks > > > support it. > > I assume Andrzej meant upstream device for the tc,dsi-lanes property. > This should be exposed through the data-lanes property as described in > media/video-interface.txt. data-lanes mainly used for the interfaces of the hardware. example : dsi, csi In general panels/bridges either it will be hardcoded by setting in the panel driver like this dsi->lanes = 4; bridge -> dsi2hdmi display/bridge/adi,adv7511.txt it wil be set by adi,dsi-lanes > > The tc,dual-link property should be replaced by exposing two port nodes, > one for each link, and connecting them appropriately. See > display/bridge/thine,thc63lvd1024.txt for an example of DT bindings on > the LVDS receiver side, and drivers/gpu/drm/rcar-du/rcar_lvds.c for an > example implementation on the LVDS transmitter side. Can we add two port nodes though it can give only 1 output? when higher resolution panel used dual_link is enabled in LVCFG > > The tc,data-format property should be replaced by the data-mapping > property on the downstream LVDS device (see display/panel/lvds.yaml) and > queried at runtime. > > > > > + - vdd-supply: 1.2V LVDS Power Supply > > > > + - vddio-supply: 1.8V IO Power Supply > > > > + - stby-gpios: Standby pin, Low active > > > > + - reset-gpios: Hardware reset, Low active > > > > + > > > > +Required nodes: > > > > + > > > > +The TC358775 has two ports. Their connections are modelled using the OF > > > > +graph bindings specified in Documentation/devicetree/bindings/graph.txt. > > > > + > > > > +- Video port 0 for the DSI input. The remote endpoint phandle should be a > > > > + reference to a valid mipi_dsi_host device node. > > > > +- Video port 1 for the LVDS output. > > > > + > > > > +Example: > > > > + > > > > + i2c@78b8000 { > > > > + /* On High speed expansion */ > > > > + label = "HS-I2C2"; > > > > + status = "okay"; > > > > + > > > > + tc_bridge: bridge@f { > > > > + status = "okay"; > > > > + > > > > + compatible = "toshiba,tc358775"; > > > > + reg = <0x0f>; > > > > + > > > > + tc,dsi-lanes = <4>; > > > > + tc,dual-link = <0>; > > > > + tc,data-format = <1>; > > > > + > > > > + vdd-supply = <&pm8916_l2>; > > > > + vddio-supply = <&pm8916_l6>; > > > > + > > > > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > > > > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > > > > + > > > > + ports { > > > > + #address-cells = <1>; > > > > + #size-cells = <0>; > > > > + > > > > + port@0 { > > > > + reg = <0>; > > > > + d2l_in: endpoint { > > > > + remote-endpoint = <&dsi0_out>; > > > > + }; > > > > + }; > > > > + > > > > + port@1 { > > > > + reg = <1>; > > > > + d2l_out: endpoint { > > > > + remote-endpoint = <&panel_in>; > > > > + }; > > > > + }; > > > > + }; > > > > + }; > > > > + }; > > > > + > > > > + panel: auo,b101xtn01 { > > > > + status = "okay"; > > > > + compatible = "auo,b101xtn01"; > > > > + power-supply = <&pm8916_l14>; > > > > + > > > > + port { > > > > + panel_in: endpoint { > > > > + remote-endpoint = <&d2l_out>; > > > > + }; > > > > + }; > > > > + }; > > > > + > > > > + mdss@1a00000 { > > > > + status = "okay"; > > > > + > > > > + mdp@1a01000 { > > > > + status = "okay"; > > > > + }; > > > > + > > > > + dsi@1a98000 { > > > > + status = "okay"; > > > > + .. > > > > + ports { > > > > + port@1 { > > > > + dsi0_out: endpoint { > > > > + remote-endpoint = <&d2l_in>; > > > > + data-lanes = <0 1 2 3>; > > > > + }; > > > > + }; > > > > + }; > > > > + }; > > > > + > > > > + dsi-phy@1a98300 { > > > > + status = "okay"; > > > > + .. > > > > + }; > > > > + }; > > > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig > > > > index 8397bf7..d5528fa 100644 > > > > --- a/drivers/gpu/drm/bridge/Kconfig > > > > +++ b/drivers/gpu/drm/bridge/Kconfig > > > > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 > > > > ---help--- > > > > Toshiba TC358767 eDP bridge chip driver. > > > > > > > > +config DRM_TOSHIBA_TC358775 > > > > + tristate "Toshiba TC358775 LVDS bridge" > > > > + depends on OF > > > > + select DRM_KMS_HELPER > > > > + select REGMAP_I2C > > > > + select DRM_PANEL > > > > + select DRM_MIPI_DSI > > > > + ---help--- > > > > + Toshiba TC358775 LVDS bridge chip driver. > > > > + > > > > config DRM_TI_TFP410 > > > > tristate "TI TFP410 DVI/HDMI bridge" > > > > depends on OF > > > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile > > > > index 1eb5376..9b2c512 100644 > > > > --- a/drivers/gpu/drm/bridge/Makefile > > > > +++ b/drivers/gpu/drm/bridge/Makefile > > > > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o > > > > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o > > > > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o > > > > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o > > > > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o > > > > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ > > > > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o > > > > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o > > > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c > > > > new file mode 100644 > > > > index 0000000..3db0f49 > > > > --- /dev/null > > > > +++ b/drivers/gpu/drm/bridge/tc358775.c > > > > @@ -0,0 +1,687 @@ > > > > +// SPDX-License-Identifier: GPL-2.0 > > > > +/* > > > > + * tc358775 DSI to LVDS bridge driver > > > > + * > > > > + * Copyright (C) 2020 InforceComputing > > > > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> > > > > + * > > > > + * This program is free software; you can redistribute it and/or modify > > > > + * it under the terms of the GNU General Public License as published by > > > > + * the Free Software Foundation; either version 2 of the License, or > > > > + * (at your option) any later version. > > > > + * > > > > + * This program is distributed in the hope that it will be useful, > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > + * GNU General Public License for more details. > > > > > > You can drop these statements, SPDX identifier is enough. > > > > > > > + */ > > > > + > > > > +/* #define DEBUG */ > > > > +/* #define TC358775_DEBUG */ > > > > > > Please remove these development leftovers. > > > > > > > +#include <linux/clk.h> > > > > +#include <linux/device.h> > > > > +#include <linux/gpio/consumer.h> > > > > +#include <linux/i2c.h> > > > > +#include <linux/kernel.h> > > > > +#include <linux/module.h> > > > > +#include <linux/regmap.h> > > > > +#include <linux/slab.h> > > > > +#include <linux/regulator/consumer.h> > > > Alphabetic order. > > > > + > > > > +#include <drm/drm_mipi_dsi.h> > > > > +#include <drm/drm_atomic_helper.h> > > > > +#include <drm/drm_crtc_helper.h> > > > > +#include <drm/drm_dp_helper.h> > > > > +#include <drm/drm_of.h> > > > > +#include <drm/drm_panel.h> > > > > +#include <drm/drm_bridge.h> > > > > +#include <drm/drm_probe_helper.h> > > > ditto > > > > + > > > > +/* Registers */ > > > > + > > > > +/* DSI D-PHY Layer Registers */ > > > > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ > > > > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ > > > > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ > > > > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ > > > > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ > > > > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ > > > > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ > > > > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ > > > > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ > > > > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ > > > > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ > > > > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ > > > > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ > > > > + > > > > +/* DSI PPI Layer Registers */ > > > > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ > > > > +#define PPI_BUSYPPI 0x0108 > > > > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ > > > > +#define PPI_LPTXTIMECNT 0x0114 > > > > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ > > > > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ > > > > + > > > > +/* Analog timer function enable */ > > > > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ > > > > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ > > > > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ > > > > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ > > > > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ > > > > +#define PPI_D0S_CLRSIPOCOUNT 0x0164 > > > > + > > > > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ > > > > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ > > > > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ > > > > + > > > > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ > > > > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ > > > > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ > > > > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ > > > > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ > > > > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ > > > > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ > > > > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ > > > > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ > > > > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ > > > > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ > > > > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ > > > > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ > > > > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ > > > > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ > > > > + > > > > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ > > > > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ > > > > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ > > > > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ > > > > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ > > > > +#define DSI_BUSYDSI 0x0208 > > > > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ > > > > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ > > > > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ > > > > + > > > > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ > > > > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ > > > > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ > > > > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ > > > > + > > > > +#define DSIERRCNT 0x0300 /* DSI Error Count */ > > > > +#define APLCTRL 0x0400 /* Application Layer Control */ > > > > +#define RDPKTLN 0x0404 /* Command Read Packet Length */ > > > > + > > > > +#define VPCTRL 0x0450 /* Video Path Control */ > > > > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ > > > > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ > > > > +#define VTIM1 0x045C /* Vertical Timing Control 1 */ > > > > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ > > > > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ > > > > + > > > > +/* Mux Input Select for LVDS LINK Input */ > > > > +#define LVMX0003 0x0480 /* Bit 0 to 3 */ > > > > +#define LVMX0407 0x0484 /* Bit 4 to 7 */ > > > > +#define LVMX0811 0x0488 /* Bit 8 to 11 */ > > > > +#define LVMX1215 0x048C /* Bit 12 to 15 */ > > > > +#define LVMX1619 0x0490 /* Bit 16 to 19 */ > > > > +#define LVMX2023 0x0494 /* Bit 20 to 23 */ > > > > +#define LVMX2427 0x0498 /* Bit 24 to 27 */ > > > > + > > > > +#define LVCFG 0x049C /* LVDS Configuration */ > > > > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ > > > > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ > > > > +#define SYSSTAT 0x0500 /* System Status */ > > > > +#define SYSRST 0x0504 /* System Reset */ > > > > +/* GPIO Registers */ > > > > +#define GPIOC 0x0520 /* GPIO Control */ > > > > +#define GPIOO 0x0524 /* GPIO Output */ > > > > +#define GPIOI 0x0528 /* GPIO Input */ > > > > + > > > > +/* I2C Registers */ > > > > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ > > > > +#define I2CMADDR 0x0544 /* I2C Master Addressing */ > > > > +#define WDATAQ 0x0548 /* Write Data Queue */ > > > > +#define RDATAQ 0x054C /* Read Data Queue */ > > > > + > > > > +/* Chip ID and Revision ID Register */ > > > > +#define IDREG 0x0580 > > > > + > > > > +#define TC358775XBG_ID 0x00007500 > > > > + > > > > +/* Debug Registers */ > > > > +#define DEBUG00 0x05A0 /* Debug */ > > > > +#define DEBUG01 0x05A4 /* LVDS Data */ > > > > + > > > > +#define DSI_CLEN_BIT BIT(0) > > > > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ > > > > +#define LVCFG_LVEN_BIT BIT(0) > > > > + > > > > +#define L0EN BIT(1) > > > > + > > > > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 > > > > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 > > > > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val) > > > > > > > > > Use u32 here and below, unit32_t is mainly for userspace interactions. > > > > > > > > > > +{ > > > > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & > > > > + TC358775_VPCTRL_VSDELAY__MASK; > > > > +} > > > > + > > > > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 > > > > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 > > > > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val) > > > > +{ > > > > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & > > > > + TC358775_VPCTRL_OPXLFMT__MASK; > > > > +} > > > > + > > > > +#define TC358775_VPCTRL_MSF__MASK 0x00000001 > > > > +#define TC358775_VPCTRL_MSF__SHIFT 0 > > > > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val) > > > > +{ > > > > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & > > > > + TC358775_VPCTRL_MSF__MASK; > > > > +} > > > > + > > > > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 > > > > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 > > > > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val) > > > > +{ > > > > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & > > > > + TC358775_LVCFG_PCLKDIV__MASK; > > > > +} > > > > + > > > > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 > > > > +#define TC358775_LVCFG_LVDLINK__SHIFT 0 > > > > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val) > > > > +{ > > > > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & > > > > + TC358775_LVCFG_LVDLINK__MASK; > > > > +} > > > > + > > > > +static const struct reg_sequence tc_fixed_registers[] = { > > > > + { 0x013C, 0x00040006 }, > > > > + { 0x0114, 0x00000004 }, > > > > + { 0x0164, 0x00000003 }, > > > > + { 0x0168, 0x00000003 }, > > > > + { 0x016C, 0x00000003 }, > > > > + { 0x0170, 0x00000003 }, > > > > > > use macros instead of magic numbers. > > > > > > > +}; > > > > + > > > > +static const struct reg_sequence tc_vesa_data_format_registers[] = { > > > > + { 0x0480, 0x03020100 }, > > > > + { 0x0484, 0x08050704 }, > > > > + { 0x0488, 0x0F0E0A09 }, > > > > + { 0x048C, 0x100D0C0B }, > > > > + { 0x0490, 0x12111716 }, > > > > + { 0x0494, 0x1B151413 }, > > > > + { 0x0498, 0x061A1918 }, > > > ditto > > > > +}; > > > > + > > > > +static const char * const regulator_names[] = { > > > > + "vdd", > > > > + "vddio" > > > > +}; > > > > + > > > > +struct tc_data { > > > > + struct i2c_client *i2c; > > > > + > > > > + struct device *dev; > > > > + struct regmap *regmap; > > > > + > > > > + struct drm_bridge bridge; > > > > + struct drm_connector connector; > > > > + struct drm_panel *panel; > > > > + > > > > + enum drm_connector_status status; > > > unused field status used in tc->status = connector_status_connected; > > > > + struct device_node *host_node; > > > > + struct mipi_dsi_device *dsi; > > > > + u8 num_dsi_lanes; > > > > + > > > > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; > > > > + struct gpio_desc *reset_gpio; > > > > + struct gpio_desc *stby_gpio; > > > > + u32 rev; > > > > + u8 dual_link; /* single-link or dual-link */ > > > > + u8 data_format; /* VESA or JEIDA */ > > > > +}; > > > > + > > > > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) > > > > +{ > > > > + return container_of(b, struct tc_data, bridge); > > > > +} > > > > + > > > > +static inline struct tc_data *connector_to_tc(struct drm_connector *c) > > > > +{ > > > > + return container_of(c, struct tc_data, connector); > > > > +} > > > > + > > > > +static void tc_bridge_pre_enable(struct drm_bridge *bridge) > > > > +{ > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > + struct device *dev = &tc->dsi->dev; > > > > + int ret; > > > > + > > > > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); > > > > + if (ret < 0) { > > > > + dev_err(dev, "regulator enable failed, %d\n", ret); > > > > + return; > > > > + } > > > > + mdelay(10); > > You should consider usleep_range() instead of mdelay() for large delays. > > > > > + > > > > + gpiod_set_value(tc->stby_gpio, 0); > > > > + mdelay(10); > > > > + > > > > + gpiod_set_value(tc->reset_gpio, 0); > > > > + ndelay(50); > > > > + > > > > + drm_panel_prepare(tc->panel); > > > > +} > > > > + > > > > +static void tc_bridge_disable(struct drm_bridge *bridge) > > > > +{ > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > + struct device *dev = &tc->dsi->dev; > > > > + int ret; > > > > + > > > > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); > > > > + if (ret < 0) > > > > + dev_err(dev, "regulator disable failed, %d\n", ret); > > > > + mdelay(10); > > > > + > > > > + gpiod_set_value(tc->stby_gpio, 1); > > > > + mdelay(10); > > > > + > > > > + gpiod_set_value(tc->reset_gpio, 1); > > > > + ndelay(50); > > > > + > > > > + drm_panel_disable(tc->panel); > > > > > > I suspect the order should be different - ie reverse to the one pre_enable. - as per the datasheet it is not in reverse order > > > > > > Moreover since it reverts pre_enable it should be put into post_disable > > > (except drm_panel_disable). > > > > > > > +} > > > > + > > > > +static void tc_bridge_post_disable(struct drm_bridge *bridge) > > > > +{ > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > + > > > > + drm_panel_unprepare(tc->panel); > > > > +} > > > > + > > > > +#ifdef TC358775_DEBUG > > > > +static u32 d2l_read(struct tc_data *tc, u16 reg) > > > > +{ > > > > + int ret; > > > > + u32 data; > > > > + > > > > + ret = regmap_bulk_read(tc->regmap, reg, &data, 1); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data); > > > > + > > > > + return data; > > > > +} > > > > +#endif > > > > > > I guess this leftover can be removed as well. > > > > > > > + > > > > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) > > > > +{ > > > > + int ret = 0; > > > > + > > > > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); > > > > + > > > > +#ifdef TC358775_DEBUG > > > > + d2l_read(tc, reg); > > > > +#endif > > > > + return ret; > > > > +} > > > > + > > > > +static void tc_bridge_enable(struct drm_bridge *bridge) > > > > +{ > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > + int ret; > > > > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; > > > > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; > > > > + u32 val = 0; > > > > + struct drm_display_mode *mode; > > > > + > > > > + mode = &bridge->encoder->crtc->state->adjusted_mode; > > > > + > > > > + hbpr = 0; > > > > + hpw = mode->hsync_end - mode->hsync_start; > > > > + vbpr = 0; > > > > + vpw = mode->vsync_end - mode->vsync_start; > > > > + > > > > + htime1 = (hbpr << 16) + hpw; > > > > + vtime1 = (vbpr << 16) + vpw; > > > > + > > > > + hfpr = mode->hsync_start - mode->hdisplay; > > > > + hsize = mode->hdisplay; > > > > + vfpr = mode->vsync_start - mode->vdisplay; > > > > + vsize = mode->vdisplay; > > > > + > > > > + htime2 = (hfpr << 16) + hsize; > > > > + vtime2 = (vfpr << 16) + vsize; > > > > + > > > > + ret = regmap_read(tc->regmap, IDREG, &tc->rev); > > > > + if (ret) { > > > > + dev_err(tc->dev, "can not read device ID: %d\n", ret); > > > > + return; > > > > + } > > > > + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev); > > > > + > > > > + d2l_write(tc, SYSRST, 0x000000FF); > > > > + mdelay(30); > > > > + > > > > + ret = regmap_register_patch(tc->regmap, > > > > + tc_fixed_registers, > > > > + ARRAY_SIZE(tc_fixed_registers)); > > > > + if (ret) > > > > + return; > > > > + > > > > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; > > > > + d2l_write(tc, PPI_LANEENABLE, val); > > > > + d2l_write(tc, DSI_LANEENABLE, val); > > > > + > > > > + d2l_write(tc, PPI_STARTPPI, 0x00000001); > > > > + d2l_write(tc, DSI_STARTDSI, 0x00000001); > > > > + > > > > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value > > > > Any suggestion how to set dynamic value for Vsyncdelay? > > > > > > + > > > > + if (tc->connector.display_info.bpc == 8) {/* RGB888 */ > > > > + val |= TC358775_VPCTRL_OPXLFMT(1); > > > > + d2l_write(tc, VPCTRL, val); > > > > + } else { /* RGB666 */ > > > > + val |= TC358775_VPCTRL_MSF(1); > > > > + d2l_write(tc, VPCTRL, val); > > > > + } > > > > + > > > > + d2l_write(tc, HTIM1, htime1); > > > > + d2l_write(tc, VTIM1, vtime1); > > > > + d2l_write(tc, HTIM2, htime2); > > > > + d2l_write(tc, VTIM2, vtime2); > > > > + > > > > + d2l_write(tc, VFUEN, 0x00000001); > > > > + d2l_write(tc, SYSRST, 0x00000004); > > > > + d2l_write(tc, LVPHY0, 0x00040006); > > > > + > > > > + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */ > > > > + ret = regmap_register_patch > > > > + (tc->regmap, > > > > + tc_vesa_data_format_registers, > > > > + ARRAY_SIZE(tc_vesa_data_format_registers)); > > > > + if (ret) > > > > + return; > > > > + } > > > > + > > > > + d2l_write(tc, VFUEN, 0x00000001); > > > > + > > > > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; > > > > + if (tc->dual_link) > > > > + val |= TC358775_LVCFG_LVDLINK(1); > > > > + > > > > + d2l_write(tc, LVCFG, val); > > > > + > > > > + drm_panel_enable(tc->panel); > > > > +} > > > > + > > > > +static int tc_connector_get_modes(struct drm_connector *connector) > > > > +{ > > > > + struct tc_data *tc = connector_to_tc(connector); > > > > + struct edid *edid; > > > > + unsigned int count; > > > > + > > > > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { > > > > + count = tc->panel->funcs->get_modes(tc->panel, connector); > > > > + if (count > 0) > > > > + return count; > > > > + } > > > > + > > > > + edid = drm_get_edid(connector, tc->i2c->adapter); > > > > + if (!edid) > > > > + return 0; > > > > + > > > > + drm_connector_update_edid_property(connector, edid); > > > > + count = drm_add_edid_modes(connector, edid); > > > > + kfree(edid); > > > > + > > > > + return count; > > > > +} > > > > + > > > > +static int tc_connector_mode_valid(struct drm_connector *connector, > > > > + struct drm_display_mode *mode) > > > > +{ > > > > + struct tc_data *tc = connector_to_tc(connector); > > > > + > > > > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ > > > > + if ((mode->clock > 135000 && tc->dual_link == 0) || > > > > + (mode->clock > 270000 && tc->dual_link == 1)) > > > > + return MODE_CLOCK_HIGH; > > > > + > > > > + return MODE_OK; > > > > +} > > This should be replaced by the bridge .mode_valid() operation, as it's > related to the bridge, not the connector. > > > > > + > > > > +static struct drm_encoder * > > > > +tc_connector_best_encoder(struct drm_connector *connector) > > > > +{ > > > > + struct tc_data *tc = connector_to_tc(connector); > > > > + > > > > + return tc->bridge.encoder; > > > > +} > > > > + > > > > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { > > > > + .get_modes = tc_connector_get_modes, > > > > + .mode_valid = tc_connector_mode_valid, > > > > + .best_encoder = tc_connector_best_encoder, > > > > +}; > > > > + > > > > +static const struct drm_connector_funcs tc_connector_funcs = { > > > > + .fill_modes = drm_helper_probe_single_connector_modes, > > > > + .destroy = drm_connector_cleanup, > > > > + .reset = drm_atomic_helper_connector_reset, > > > > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > > > > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > > > > +}; > > > > + > > > > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) > > > > +{ > > > > + u32 num_lanes; > > > > + u8 dual_link, data_format; > > > > + > > > > + of_property_read_u8(np, "tc,dual-link", &dual_link); > > > > + of_property_read_u8(np, "tc,data-format", &data_format); > > > > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); > > > > + > > > > + if (num_lanes < 1 || num_lanes > 4) > > > > + return -EINVAL; > > > > + > > > > + tc->num_dsi_lanes = num_lanes; > > > > + tc->dual_link = dual_link; > > > > + tc->data_format = data_format; > > > > + > > > > + tc->host_node = of_graph_get_remote_node(np, 0, 0); > > > > + if (!tc->host_node) > > > > + return -ENODEV; > > > > + > > > > + of_node_put(tc->host_node); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +int tc358775_attach_dsi(struct tc_data *tc) > > > > +{ > > > > + struct device *dev = &tc->i2c->dev; > > > > + struct mipi_dsi_host *host; > > > > + struct mipi_dsi_device *dsi; > > > > + int ret = 0; > > > > + const struct mipi_dsi_device_info info = { .type = "tc358775", > > > > + .channel = 0, > > > > + .node = NULL, > > > > + }; > > > > + > > > > + host = of_find_mipi_dsi_host_by_node(tc->host_node); > > > > + if (!host) { > > > > + dev_err(dev, "failed to find dsi host\n"); > > > > + return -EPROBE_DEFER; > > > > + } > > > > + > > > > + dsi = mipi_dsi_device_register_full(host, &info); > > > > + if (IS_ERR(dsi)) { > > > > + dev_err(dev, "failed to create dsi device\n"); > > > > + ret = PTR_ERR(dsi); > > > > + goto err_dsi_device; > > > > + } > > > > + > > > > + tc->dsi = dsi; > > > > + > > > > + dsi->lanes = tc->num_dsi_lanes; > > > > + dsi->format = MIPI_DSI_FMT_RGB888; > > > > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; > > > > + > > > > + ret = mipi_dsi_attach(dsi); > > > > + if (ret < 0) { > > > > + dev_err(dev, "failed to attach dsi to host\n"); > > > > + goto err_dsi_attach; > > > > + } > > > > + > > > > + return 0; > > > > + > > > > +err_dsi_attach: > > > > + mipi_dsi_device_unregister(dsi); > > > > +err_dsi_device: > > > > + return ret; > > > > +} > > > > + > > > > +static int tc_bridge_attach(struct drm_bridge *bridge) > > > > +{ > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > + struct drm_device *drm = bridge->dev; > > > > + int ret; > > > > + > > > > + /* Create LVDS connector */ > > > > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); > > > > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, > > > > + DRM_MODE_CONNECTOR_LVDS); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + if (tc->panel) > > > > + drm_panel_attach(tc->panel, &tc->connector); > > > > + > > > > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); > > > > + > > > > + ret = tc358775_attach_dsi(tc); > > > > > > Ignored retval. > > > > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static const struct drm_bridge_funcs tc_bridge_funcs = { > > > > + .attach = tc_bridge_attach, > > > > + .pre_enable = tc_bridge_pre_enable, > > > > + .enable = tc_bridge_enable, > > > > + .disable = tc_bridge_disable, > > > > + .post_disable = tc_bridge_post_disable, > > > > +}; > > > > + > > > > +static const struct regmap_config tc_regmap_config = { > > > > + .name = "tc358775", > > > > + .reg_bits = 16, > > > > + .val_bits = 32, > > > > + .reg_stride = 4, > > > > + .max_register = 0x05A8, > > > > + .cache_type = REGCACHE_RBTREE, > > > > + .reg_format_endian = REGMAP_ENDIAN_BIG, > > > > + .val_format_endian = REGMAP_ENDIAN_LITTLE, > > > > +}; > > > > + > > > > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) > > > > +{ > > > > + struct device *dev = &client->dev; > > > > + struct tc_data *tc; > > > > + int ret; > > > > + unsigned int i; > > > > + > > > > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); > > > > + if (!tc) > > > > + return -ENOMEM; > > > > + > > > > + tc->dev = dev; > > > > + tc->i2c = client; > > > > + tc->status = connector_status_connected; > > > > + > > > > + /* port@1 is the output port */ > > > > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); > > > > + if (ret && ret != -ENODEV) > > > > + return ret; > > You should support cases where the next device is a bridge. I recommand > wrapping the panel in a drm_panel_bridge with drm_panel_bridge_add(), > and then handling the next component as a bridge in all code paths. This > will allow removing manual enable/disable of panels above, as bridge > chaining is handled automatically. drm_panel_bridge creates a > drm_connector, so you can drop your manual connector implementation > here, simplifying the code. > i am not clear on this drm_panel_bridge_add() usage, please clarify/any reference would be helpful. > > > > + > > > > + ret = tc358775_parse_dt(dev->of_node, tc); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) > > > > + tc->supplies[i].supply = regulator_names[i]; > > > > + > > > > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), > > > > + tc->supplies); > > > > + if (ret < 0) > > > > + dev_err(dev, "failed to init regulator, ret=%d\n", ret); > > > > + > > > > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); > > > > + if (IS_ERR(tc->stby_gpio)) { > > > > + ret = PTR_ERR(tc->stby_gpio); > > > > + dev_err(dev, "cannot get stby-gpio %d\n", ret); > > > > + return ret; > > > > + } > > > > + > > > > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > > > > + if (IS_ERR(tc->reset_gpio)) { > > > > + ret = PTR_ERR(tc->reset_gpio); > > > > + dev_err(dev, "cannot get reset-gpios %d\n", ret); > > > > + return ret; > > > > + } > > > > + > > > > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); > > > > + if (IS_ERR(tc->regmap)) { > > > > + ret = PTR_ERR(tc->regmap); > > > > + dev_err(dev, "Failed to initialize regmap: %d\n", ret); > > > > + return ret; > > > > + } > > > > + > > > > + tc->bridge.funcs = &tc_bridge_funcs; > > > > + tc->bridge.of_node = dev->of_node; > > > > + drm_bridge_add(&tc->bridge); > > > > + > > > > + i2c_set_clientdata(client, tc); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int tc_remove(struct i2c_client *client) > > > > +{ > > > > + struct tc_data *tc = i2c_get_clientdata(client); > > > > + > > > > + drm_bridge_remove(&tc->bridge); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static const struct i2c_device_id tc358775_i2c_ids[] = { > > > > + { "tc358775", 0 }, > > > > + { } > > > > +}; > > > > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); > > > > + > > > > +static const struct of_device_id tc358775_of_ids[] = { > > > > + { .compatible = "toshiba,tc358775", }, > > > > + { } > > > > +}; > > > > +MODULE_DEVICE_TABLE(of, tc358775_of_ids); > > > > + > > > > +static struct i2c_driver tc358775_driver = { > > > > + .driver = { > > > > + .name = "tc358775", > > > > + .of_match_table = tc358775_of_ids, > > > > + }, > > > > + .id_table = tc358775_i2c_ids, > > > > + .probe = tc_probe, > > > > + .remove = tc_remove, > > > > +}; > > > > +module_i2c_driver(tc358775_driver); > > > > + > > > > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); > > > > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); > > > > > > maybe better: > > > > > > tc358775 DSI/LVDS bridge driver > > > > > > > +MODULE_LICENSE("GPL v2"); > > -- > Regards, > > Laurent Pinchart -- regards, vinaysimha _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hi Vinay, On Wed, Mar 11, 2020 at 03:30:48PM +0530, Vinay Simha B N wrote: > Laurent Pinchart, > > if we want to set to jeida-18 data mapping, > do we need to set DATA3 with "Logic 0" LVI_L0 ? If the TC358775 supports setting unused outputs to a fixed logic level I think that's best, yes. > Please see reply inline. Same :-) > > > > On Fri, Mar 06, 2020 at 06:06:36PM +0530, Vinay Simha B N wrote: > > > hi andrzej, > > > > > > I had a doubt In the tc358764 driver,VP_CTRL, VP_CTRL_VSDELAY(15) is > > > hardcoded to 15, but this has to be dynamic based on the resolution of > > > panel used? > > > > > > Please see the reply inline. > > > > > > On Tue, Mar 3, 2020 at 8:39 PM Andrzej Hajda <a.hajda@samsung.com> wrote: > > > > On 27.02.2020 15:03, Vinay Simha BN wrote: > > > > > dsi2lvds tc358775 bridge driver added > > > > > Tested in apq8016, ifc6309 board and panel > > > > > auo,b101xtn01 > > > > > > > > Just FYI, there exists already TC358764/5 driver for similar hw, but > > > > controlled via DSI bus. > > > > > > There is not much difference between these two chips, but still the > > > dsi read access for 775 does not works. > > > TC358764/5 - 800Mbps per lane, 3.2Gbps > > > TC358775 - 1Gbps per lane, 4Gbps. > > > > > > tc358775 chip details - > > > https://download.t-firefly.com/product/RK3399/Docs/Chip%20Specifications/TC358774XBG_75XBG_V1%204nm.pdf > > > I am able to configure the tc358775 chip by i2c, but from dsi it fails > > > i tried accessing the tc358775 chip by dsi using apq8016-qcom , but it > > > fails to read the chip id itself. > > > > > > Please suggest if you any inputs for this issue. > > > > > > https://github.com/vinaysimhabn/kernel-msm/commits/5.6.0-rc3-dsi2lvds-dsi > > > > > > [ 4.582405] tc358764 1a98000.dsi.0: read: 1408, addr: 0 > > > [ 4.582426] tc358764 1a98000.dsi.0: ID: 0x0 > > > [ 4.582451] tc358764 1a98000.dsi.0: error initializing bridge (-22) > > > > > > [ 4.796220] dsi_cmds2buf_tx: cmd dma tx failed, type=0x24, data0=0x80, len=4 > > > [ 4.796244] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > > [ 4.796266] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > > [ 4.796288] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > > [ 4.796310] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0 > > > [ 4.796319] msm_dsi_host_cmd_rx:Invalid response cmd > > > > > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> > > > > > --- > > > > > .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++ > > > > > > > > Bindings should be in separate patch and in yaml format. > > > > > > > > > drivers/gpu/drm/bridge/Kconfig | 10 + > > > > > drivers/gpu/drm/bridge/Makefile | 1 + > > > > > drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++ > > > > > 4 files changed, 804 insertions(+) > > > > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > > > create mode 100644 drivers/gpu/drm/bridge/tc358775.c > > > > > > > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > > > new file mode 100644 > > > > > index 0000000..c4c364d > > > > > --- /dev/null > > > > > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt > > > > > @@ -0,0 +1,106 @@ > > > > > +Toshiba TC358775 DSI to LVDS bridge bindings > > > > > + > > > > > +Required properties: > > > > > + - compatible: "toshiba,tc358775" > > > > > + - reg: i2c address of the bridge, 0x0f > > > > > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should > > > > > + be one of 1, 2, 3 or 4. > > > > > + - tc, dual-link : To configure the LVDS transmitter either > > > > > + as single-link or dual-link. > > > > > + - tc, data-format: To configure the data formats > > > > > + 0 for VESA standard, 1 for JEIDA standard > > > > > > > > IMO, three properties above should be received from downstream device in > > > > runtime, not hardcoded into DT, however I am not sure if frameworks > > > > support it. > > > > I assume Andrzej meant upstream device for the tc,dsi-lanes property. > > This should be exposed through the data-lanes property as described in > > media/video-interface.txt. > > data-lanes mainly used for the interfaces of the hardware. > example : dsi, csi Correct, so please use it to replace tc,dsi-lanes :-) > In general panels/bridges either it will be hardcoded by setting in the > panel driver like this dsi->lanes = 4; > bridge -> dsi2hdmi display/bridge/adi,adv7511.txt it wil be set by > adi,dsi-lanes That's a mistake in the bindings, let's not repeat it. > > The tc,dual-link property should be replaced by exposing two port nodes, > > one for each link, and connecting them appropriately. See > > display/bridge/thine,thc63lvd1024.txt for an example of DT bindings on > > the LVDS receiver side, and drivers/gpu/drm/rcar-du/rcar_lvds.c for an > > example implementation on the LVDS transmitter side. > > Can we add two port nodes though it can give only 1 output? when > higher resolution panel used dual_link is enabled in LVCFG Sure, you will have three ports in total, one for the DSI intput, and two for the two LVDS outputs. A port node maps to a physical connection, and there's nothing wrong with having two port nodes to describe the dual-link LVDS output. > > The tc,data-format property should be replaced by the data-mapping > > property on the downstream LVDS device (see display/panel/lvds.yaml) and > > queried at runtime. > > > > > > > + - vdd-supply: 1.2V LVDS Power Supply > > > > > + - vddio-supply: 1.8V IO Power Supply > > > > > + - stby-gpios: Standby pin, Low active > > > > > + - reset-gpios: Hardware reset, Low active > > > > > + > > > > > +Required nodes: > > > > > + > > > > > +The TC358775 has two ports. Their connections are modelled using the OF > > > > > +graph bindings specified in Documentation/devicetree/bindings/graph.txt. > > > > > + > > > > > +- Video port 0 for the DSI input. The remote endpoint phandle should be a > > > > > + reference to a valid mipi_dsi_host device node. > > > > > +- Video port 1 for the LVDS output. > > > > > + > > > > > +Example: > > > > > + > > > > > + i2c@78b8000 { > > > > > + /* On High speed expansion */ > > > > > + label = "HS-I2C2"; > > > > > + status = "okay"; > > > > > + > > > > > + tc_bridge: bridge@f { > > > > > + status = "okay"; > > > > > + > > > > > + compatible = "toshiba,tc358775"; > > > > > + reg = <0x0f>; > > > > > + > > > > > + tc,dsi-lanes = <4>; > > > > > + tc,dual-link = <0>; > > > > > + tc,data-format = <1>; > > > > > + > > > > > + vdd-supply = <&pm8916_l2>; > > > > > + vddio-supply = <&pm8916_l6>; > > > > > + > > > > > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; > > > > > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; > > > > > + > > > > > + ports { > > > > > + #address-cells = <1>; > > > > > + #size-cells = <0>; > > > > > + > > > > > + port@0 { > > > > > + reg = <0>; > > > > > + d2l_in: endpoint { > > > > > + remote-endpoint = <&dsi0_out>; > > > > > + }; > > > > > + }; > > > > > + > > > > > + port@1 { > > > > > + reg = <1>; > > > > > + d2l_out: endpoint { > > > > > + remote-endpoint = <&panel_in>; > > > > > + }; > > > > > + }; > > > > > + }; > > > > > + }; > > > > > + }; > > > > > + > > > > > + panel: auo,b101xtn01 { > > > > > + status = "okay"; > > > > > + compatible = "auo,b101xtn01"; > > > > > + power-supply = <&pm8916_l14>; > > > > > + > > > > > + port { > > > > > + panel_in: endpoint { > > > > > + remote-endpoint = <&d2l_out>; > > > > > + }; > > > > > + }; > > > > > + }; > > > > > + > > > > > + mdss@1a00000 { > > > > > + status = "okay"; > > > > > + > > > > > + mdp@1a01000 { > > > > > + status = "okay"; > > > > > + }; > > > > > + > > > > > + dsi@1a98000 { > > > > > + status = "okay"; > > > > > + .. > > > > > + ports { > > > > > + port@1 { > > > > > + dsi0_out: endpoint { > > > > > + remote-endpoint = <&d2l_in>; > > > > > + data-lanes = <0 1 2 3>; > > > > > + }; > > > > > + }; > > > > > + }; > > > > > + }; > > > > > + > > > > > + dsi-phy@1a98300 { > > > > > + status = "okay"; > > > > > + .. > > > > > + }; > > > > > + }; > > > > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig > > > > > index 8397bf7..d5528fa 100644 > > > > > --- a/drivers/gpu/drm/bridge/Kconfig > > > > > +++ b/drivers/gpu/drm/bridge/Kconfig > > > > > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 > > > > > ---help--- > > > > > Toshiba TC358767 eDP bridge chip driver. > > > > > > > > > > +config DRM_TOSHIBA_TC358775 > > > > > + tristate "Toshiba TC358775 LVDS bridge" > > > > > + depends on OF > > > > > + select DRM_KMS_HELPER > > > > > + select REGMAP_I2C > > > > > + select DRM_PANEL > > > > > + select DRM_MIPI_DSI > > > > > + ---help--- > > > > > + Toshiba TC358775 LVDS bridge chip driver. > > > > > + > > > > > config DRM_TI_TFP410 > > > > > tristate "TI TFP410 DVI/HDMI bridge" > > > > > depends on OF > > > > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile > > > > > index 1eb5376..9b2c512 100644 > > > > > --- a/drivers/gpu/drm/bridge/Makefile > > > > > +++ b/drivers/gpu/drm/bridge/Makefile > > > > > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o > > > > > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o > > > > > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o > > > > > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o > > > > > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o > > > > > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ > > > > > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o > > > > > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o > > > > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c > > > > > new file mode 100644 > > > > > index 0000000..3db0f49 > > > > > --- /dev/null > > > > > +++ b/drivers/gpu/drm/bridge/tc358775.c > > > > > @@ -0,0 +1,687 @@ > > > > > +// SPDX-License-Identifier: GPL-2.0 > > > > > +/* > > > > > + * tc358775 DSI to LVDS bridge driver > > > > > + * > > > > > + * Copyright (C) 2020 InforceComputing > > > > > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> > > > > > + * > > > > > + * This program is free software; you can redistribute it and/or modify > > > > > + * it under the terms of the GNU General Public License as published by > > > > > + * the Free Software Foundation; either version 2 of the License, or > > > > > + * (at your option) any later version. > > > > > + * > > > > > + * This program is distributed in the hope that it will be useful, > > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > > + * GNU General Public License for more details. > > > > > > > > You can drop these statements, SPDX identifier is enough. > > > > > > > > > + */ > > > > > + > > > > > +/* #define DEBUG */ > > > > > +/* #define TC358775_DEBUG */ > > > > > > > > Please remove these development leftovers. > > > > > > > > > +#include <linux/clk.h> > > > > > +#include <linux/device.h> > > > > > +#include <linux/gpio/consumer.h> > > > > > +#include <linux/i2c.h> > > > > > +#include <linux/kernel.h> > > > > > +#include <linux/module.h> > > > > > +#include <linux/regmap.h> > > > > > +#include <linux/slab.h> > > > > > +#include <linux/regulator/consumer.h> > > > > Alphabetic order. > > > > > + > > > > > +#include <drm/drm_mipi_dsi.h> > > > > > +#include <drm/drm_atomic_helper.h> > > > > > +#include <drm/drm_crtc_helper.h> > > > > > +#include <drm/drm_dp_helper.h> > > > > > +#include <drm/drm_of.h> > > > > > +#include <drm/drm_panel.h> > > > > > +#include <drm/drm_bridge.h> > > > > > +#include <drm/drm_probe_helper.h> > > > > ditto > > > > > + > > > > > +/* Registers */ > > > > > + > > > > > +/* DSI D-PHY Layer Registers */ > > > > > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ > > > > > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ > > > > > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ > > > > > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ > > > > > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ > > > > > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ > > > > > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ > > > > > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ > > > > > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ > > > > > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ > > > > > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ > > > > > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ > > > > > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ > > > > > + > > > > > +/* DSI PPI Layer Registers */ > > > > > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ > > > > > +#define PPI_BUSYPPI 0x0108 > > > > > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ > > > > > +#define PPI_LPTXTIMECNT 0x0114 > > > > > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ > > > > > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ > > > > > + > > > > > +/* Analog timer function enable */ > > > > > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ > > > > > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ > > > > > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ > > > > > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ > > > > > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ > > > > > +#define PPI_D0S_CLRSIPOCOUNT 0x0164 > > > > > + > > > > > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ > > > > > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ > > > > > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ > > > > > + > > > > > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ > > > > > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ > > > > > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ > > > > > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ > > > > > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ > > > > > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ > > > > > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ > > > > > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ > > > > > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ > > > > > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ > > > > > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ > > > > > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ > > > > > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ > > > > > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ > > > > > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ > > > > > + > > > > > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ > > > > > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ > > > > > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ > > > > > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ > > > > > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ > > > > > +#define DSI_BUSYDSI 0x0208 > > > > > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ > > > > > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ > > > > > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ > > > > > + > > > > > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ > > > > > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ > > > > > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ > > > > > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ > > > > > + > > > > > +#define DSIERRCNT 0x0300 /* DSI Error Count */ > > > > > +#define APLCTRL 0x0400 /* Application Layer Control */ > > > > > +#define RDPKTLN 0x0404 /* Command Read Packet Length */ > > > > > + > > > > > +#define VPCTRL 0x0450 /* Video Path Control */ > > > > > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ > > > > > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ > > > > > +#define VTIM1 0x045C /* Vertical Timing Control 1 */ > > > > > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ > > > > > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ > > > > > + > > > > > +/* Mux Input Select for LVDS LINK Input */ > > > > > +#define LVMX0003 0x0480 /* Bit 0 to 3 */ > > > > > +#define LVMX0407 0x0484 /* Bit 4 to 7 */ > > > > > +#define LVMX0811 0x0488 /* Bit 8 to 11 */ > > > > > +#define LVMX1215 0x048C /* Bit 12 to 15 */ > > > > > +#define LVMX1619 0x0490 /* Bit 16 to 19 */ > > > > > +#define LVMX2023 0x0494 /* Bit 20 to 23 */ > > > > > +#define LVMX2427 0x0498 /* Bit 24 to 27 */ > > > > > + > > > > > +#define LVCFG 0x049C /* LVDS Configuration */ > > > > > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ > > > > > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ > > > > > +#define SYSSTAT 0x0500 /* System Status */ > > > > > +#define SYSRST 0x0504 /* System Reset */ > > > > > +/* GPIO Registers */ > > > > > +#define GPIOC 0x0520 /* GPIO Control */ > > > > > +#define GPIOO 0x0524 /* GPIO Output */ > > > > > +#define GPIOI 0x0528 /* GPIO Input */ > > > > > + > > > > > +/* I2C Registers */ > > > > > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ > > > > > +#define I2CMADDR 0x0544 /* I2C Master Addressing */ > > > > > +#define WDATAQ 0x0548 /* Write Data Queue */ > > > > > +#define RDATAQ 0x054C /* Read Data Queue */ > > > > > + > > > > > +/* Chip ID and Revision ID Register */ > > > > > +#define IDREG 0x0580 > > > > > + > > > > > +#define TC358775XBG_ID 0x00007500 > > > > > + > > > > > +/* Debug Registers */ > > > > > +#define DEBUG00 0x05A0 /* Debug */ > > > > > +#define DEBUG01 0x05A4 /* LVDS Data */ > > > > > + > > > > > +#define DSI_CLEN_BIT BIT(0) > > > > > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ > > > > > +#define LVCFG_LVEN_BIT BIT(0) > > > > > + > > > > > +#define L0EN BIT(1) > > > > > + > > > > > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 > > > > > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 > > > > > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val) > > > > > > > > > > > > Use u32 here and below, unit32_t is mainly for userspace interactions. > > > > > > > > > > > > > +{ > > > > > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & > > > > > + TC358775_VPCTRL_VSDELAY__MASK; > > > > > +} > > > > > + > > > > > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 > > > > > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 > > > > > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val) > > > > > +{ > > > > > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & > > > > > + TC358775_VPCTRL_OPXLFMT__MASK; > > > > > +} > > > > > + > > > > > +#define TC358775_VPCTRL_MSF__MASK 0x00000001 > > > > > +#define TC358775_VPCTRL_MSF__SHIFT 0 > > > > > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val) > > > > > +{ > > > > > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & > > > > > + TC358775_VPCTRL_MSF__MASK; > > > > > +} > > > > > + > > > > > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 > > > > > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 > > > > > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val) > > > > > +{ > > > > > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & > > > > > + TC358775_LVCFG_PCLKDIV__MASK; > > > > > +} > > > > > + > > > > > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 > > > > > +#define TC358775_LVCFG_LVDLINK__SHIFT 0 > > > > > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val) > > > > > +{ > > > > > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & > > > > > + TC358775_LVCFG_LVDLINK__MASK; > > > > > +} > > > > > + > > > > > +static const struct reg_sequence tc_fixed_registers[] = { > > > > > + { 0x013C, 0x00040006 }, > > > > > + { 0x0114, 0x00000004 }, > > > > > + { 0x0164, 0x00000003 }, > > > > > + { 0x0168, 0x00000003 }, > > > > > + { 0x016C, 0x00000003 }, > > > > > + { 0x0170, 0x00000003 }, > > > > > > > > use macros instead of magic numbers. > > > > > > > > > +}; > > > > > + > > > > > +static const struct reg_sequence tc_vesa_data_format_registers[] = { > > > > > + { 0x0480, 0x03020100 }, > > > > > + { 0x0484, 0x08050704 }, > > > > > + { 0x0488, 0x0F0E0A09 }, > > > > > + { 0x048C, 0x100D0C0B }, > > > > > + { 0x0490, 0x12111716 }, > > > > > + { 0x0494, 0x1B151413 }, > > > > > + { 0x0498, 0x061A1918 }, > > > > ditto > > > > > +}; > > > > > + > > > > > +static const char * const regulator_names[] = { > > > > > + "vdd", > > > > > + "vddio" > > > > > +}; > > > > > + > > > > > +struct tc_data { > > > > > + struct i2c_client *i2c; > > > > > + > > > > > + struct device *dev; > > > > > + struct regmap *regmap; > > > > > + > > > > > + struct drm_bridge bridge; > > > > > + struct drm_connector connector; > > > > > + struct drm_panel *panel; > > > > > + > > > > > + enum drm_connector_status status; > > > > unused field > status used in tc->status = connector_status_connected; > > > > > + struct device_node *host_node; > > > > > + struct mipi_dsi_device *dsi; > > > > > + u8 num_dsi_lanes; > > > > > + > > > > > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; > > > > > + struct gpio_desc *reset_gpio; > > > > > + struct gpio_desc *stby_gpio; > > > > > + u32 rev; > > > > > + u8 dual_link; /* single-link or dual-link */ > > > > > + u8 data_format; /* VESA or JEIDA */ > > > > > +}; > > > > > + > > > > > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) > > > > > +{ > > > > > + return container_of(b, struct tc_data, bridge); > > > > > +} > > > > > + > > > > > +static inline struct tc_data *connector_to_tc(struct drm_connector *c) > > > > > +{ > > > > > + return container_of(c, struct tc_data, connector); > > > > > +} > > > > > + > > > > > +static void tc_bridge_pre_enable(struct drm_bridge *bridge) > > > > > +{ > > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > > + struct device *dev = &tc->dsi->dev; > > > > > + int ret; > > > > > + > > > > > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); > > > > > + if (ret < 0) { > > > > > + dev_err(dev, "regulator enable failed, %d\n", ret); > > > > > + return; > > > > > + } > > > > > + mdelay(10); > > > > You should consider usleep_range() instead of mdelay() for large delays. > > > > > > > + > > > > > + gpiod_set_value(tc->stby_gpio, 0); > > > > > + mdelay(10); > > > > > + > > > > > + gpiod_set_value(tc->reset_gpio, 0); > > > > > + ndelay(50); > > > > > + > > > > > + drm_panel_prepare(tc->panel); > > > > > +} > > > > > + > > > > > +static void tc_bridge_disable(struct drm_bridge *bridge) > > > > > +{ > > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > > + struct device *dev = &tc->dsi->dev; > > > > > + int ret; > > > > > + > > > > > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); > > > > > + if (ret < 0) > > > > > + dev_err(dev, "regulator disable failed, %d\n", ret); > > > > > + mdelay(10); > > > > > + > > > > > + gpiod_set_value(tc->stby_gpio, 1); > > > > > + mdelay(10); > > > > > + > > > > > + gpiod_set_value(tc->reset_gpio, 1); > > > > > + ndelay(50); > > > > > + > > > > > + drm_panel_disable(tc->panel); > > > > > > > > I suspect the order should be different - ie reverse to the one pre_enable. > - as per the datasheet it is not in reverse order > > > > > > > > > Moreover since it reverts pre_enable it should be put into post_disable > > > > (except drm_panel_disable). > > > > > > > > > +} > > > > > + > > > > > +static void tc_bridge_post_disable(struct drm_bridge *bridge) > > > > > +{ > > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > > + > > > > > + drm_panel_unprepare(tc->panel); > > > > > +} > > > > > + > > > > > +#ifdef TC358775_DEBUG > > > > > +static u32 d2l_read(struct tc_data *tc, u16 reg) > > > > > +{ > > > > > + int ret; > > > > > + u32 data; > > > > > + > > > > > + ret = regmap_bulk_read(tc->regmap, reg, &data, 1); > > > > > + if (ret) > > > > > + return ret; > > > > > + > > > > > + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data); > > > > > + > > > > > + return data; > > > > > +} > > > > > +#endif > > > > > > > > I guess this leftover can be removed as well. > > > > > > > > > + > > > > > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) > > > > > +{ > > > > > + int ret = 0; > > > > > + > > > > > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); > > > > > + > > > > > +#ifdef TC358775_DEBUG > > > > > + d2l_read(tc, reg); > > > > > +#endif > > > > > + return ret; > > > > > +} > > > > > + > > > > > +static void tc_bridge_enable(struct drm_bridge *bridge) > > > > > +{ > > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > > + int ret; > > > > > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; > > > > > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; > > > > > + u32 val = 0; > > > > > + struct drm_display_mode *mode; > > > > > + > > > > > + mode = &bridge->encoder->crtc->state->adjusted_mode; > > > > > + > > > > > + hbpr = 0; > > > > > + hpw = mode->hsync_end - mode->hsync_start; > > > > > + vbpr = 0; > > > > > + vpw = mode->vsync_end - mode->vsync_start; > > > > > + > > > > > + htime1 = (hbpr << 16) + hpw; > > > > > + vtime1 = (vbpr << 16) + vpw; > > > > > + > > > > > + hfpr = mode->hsync_start - mode->hdisplay; > > > > > + hsize = mode->hdisplay; > > > > > + vfpr = mode->vsync_start - mode->vdisplay; > > > > > + vsize = mode->vdisplay; > > > > > + > > > > > + htime2 = (hfpr << 16) + hsize; > > > > > + vtime2 = (vfpr << 16) + vsize; > > > > > + > > > > > + ret = regmap_read(tc->regmap, IDREG, &tc->rev); > > > > > + if (ret) { > > > > > + dev_err(tc->dev, "can not read device ID: %d\n", ret); > > > > > + return; > > > > > + } > > > > > + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev); > > > > > + > > > > > + d2l_write(tc, SYSRST, 0x000000FF); > > > > > + mdelay(30); > > > > > + > > > > > + ret = regmap_register_patch(tc->regmap, > > > > > + tc_fixed_registers, > > > > > + ARRAY_SIZE(tc_fixed_registers)); > > > > > + if (ret) > > > > > + return; > > > > > + > > > > > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; > > > > > + d2l_write(tc, PPI_LANEENABLE, val); > > > > > + d2l_write(tc, DSI_LANEENABLE, val); > > > > > + > > > > > + d2l_write(tc, PPI_STARTPPI, 0x00000001); > > > > > + d2l_write(tc, DSI_STARTDSI, 0x00000001); > > > > > + > > > > > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value > > > > > > Any suggestion how to set dynamic value for Vsyncdelay? > > > > > > > > + > > > > > + if (tc->connector.display_info.bpc == 8) {/* RGB888 */ > > > > > + val |= TC358775_VPCTRL_OPXLFMT(1); > > > > > + d2l_write(tc, VPCTRL, val); > > > > > + } else { /* RGB666 */ > > > > > + val |= TC358775_VPCTRL_MSF(1); > > > > > + d2l_write(tc, VPCTRL, val); > > > > > + } > > > > > + > > > > > + d2l_write(tc, HTIM1, htime1); > > > > > + d2l_write(tc, VTIM1, vtime1); > > > > > + d2l_write(tc, HTIM2, htime2); > > > > > + d2l_write(tc, VTIM2, vtime2); > > > > > + > > > > > + d2l_write(tc, VFUEN, 0x00000001); > > > > > + d2l_write(tc, SYSRST, 0x00000004); > > > > > + d2l_write(tc, LVPHY0, 0x00040006); > > > > > + > > > > > + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */ > > > > > + ret = regmap_register_patch > > > > > + (tc->regmap, > > > > > + tc_vesa_data_format_registers, > > > > > + ARRAY_SIZE(tc_vesa_data_format_registers)); > > > > > + if (ret) > > > > > + return; > > > > > + } > > > > > + > > > > > + d2l_write(tc, VFUEN, 0x00000001); > > > > > + > > > > > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; > > > > > + if (tc->dual_link) > > > > > + val |= TC358775_LVCFG_LVDLINK(1); > > > > > + > > > > > + d2l_write(tc, LVCFG, val); > > > > > + > > > > > + drm_panel_enable(tc->panel); > > > > > +} > > > > > + > > > > > +static int tc_connector_get_modes(struct drm_connector *connector) > > > > > +{ > > > > > + struct tc_data *tc = connector_to_tc(connector); > > > > > + struct edid *edid; > > > > > + unsigned int count; > > > > > + > > > > > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { > > > > > + count = tc->panel->funcs->get_modes(tc->panel, connector); > > > > > + if (count > 0) > > > > > + return count; > > > > > + } > > > > > + > > > > > + edid = drm_get_edid(connector, tc->i2c->adapter); > > > > > + if (!edid) > > > > > + return 0; > > > > > + > > > > > + drm_connector_update_edid_property(connector, edid); > > > > > + count = drm_add_edid_modes(connector, edid); > > > > > + kfree(edid); > > > > > + > > > > > + return count; > > > > > +} > > > > > + > > > > > +static int tc_connector_mode_valid(struct drm_connector *connector, > > > > > + struct drm_display_mode *mode) > > > > > +{ > > > > > + struct tc_data *tc = connector_to_tc(connector); > > > > > + > > > > > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ > > > > > + if ((mode->clock > 135000 && tc->dual_link == 0) || > > > > > + (mode->clock > 270000 && tc->dual_link == 1)) > > > > > + return MODE_CLOCK_HIGH; > > > > > + > > > > > + return MODE_OK; > > > > > +} > > > > This should be replaced by the bridge .mode_valid() operation, as it's > > related to the bridge, not the connector. > > > > > > > + > > > > > +static struct drm_encoder * > > > > > +tc_connector_best_encoder(struct drm_connector *connector) > > > > > +{ > > > > > + struct tc_data *tc = connector_to_tc(connector); > > > > > + > > > > > + return tc->bridge.encoder; > > > > > +} > > > > > + > > > > > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { > > > > > + .get_modes = tc_connector_get_modes, > > > > > + .mode_valid = tc_connector_mode_valid, > > > > > + .best_encoder = tc_connector_best_encoder, > > > > > +}; > > > > > + > > > > > +static const struct drm_connector_funcs tc_connector_funcs = { > > > > > + .fill_modes = drm_helper_probe_single_connector_modes, > > > > > + .destroy = drm_connector_cleanup, > > > > > + .reset = drm_atomic_helper_connector_reset, > > > > > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > > > > > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > > > > > +}; > > > > > + > > > > > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) > > > > > +{ > > > > > + u32 num_lanes; > > > > > + u8 dual_link, data_format; > > > > > + > > > > > + of_property_read_u8(np, "tc,dual-link", &dual_link); > > > > > + of_property_read_u8(np, "tc,data-format", &data_format); > > > > > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); > > > > > + > > > > > + if (num_lanes < 1 || num_lanes > 4) > > > > > + return -EINVAL; > > > > > + > > > > > + tc->num_dsi_lanes = num_lanes; > > > > > + tc->dual_link = dual_link; > > > > > + tc->data_format = data_format; > > > > > + > > > > > + tc->host_node = of_graph_get_remote_node(np, 0, 0); > > > > > + if (!tc->host_node) > > > > > + return -ENODEV; > > > > > + > > > > > + of_node_put(tc->host_node); > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +int tc358775_attach_dsi(struct tc_data *tc) > > > > > +{ > > > > > + struct device *dev = &tc->i2c->dev; > > > > > + struct mipi_dsi_host *host; > > > > > + struct mipi_dsi_device *dsi; > > > > > + int ret = 0; > > > > > + const struct mipi_dsi_device_info info = { .type = "tc358775", > > > > > + .channel = 0, > > > > > + .node = NULL, > > > > > + }; > > > > > + > > > > > + host = of_find_mipi_dsi_host_by_node(tc->host_node); > > > > > + if (!host) { > > > > > + dev_err(dev, "failed to find dsi host\n"); > > > > > + return -EPROBE_DEFER; > > > > > + } > > > > > + > > > > > + dsi = mipi_dsi_device_register_full(host, &info); > > > > > + if (IS_ERR(dsi)) { > > > > > + dev_err(dev, "failed to create dsi device\n"); > > > > > + ret = PTR_ERR(dsi); > > > > > + goto err_dsi_device; > > > > > + } > > > > > + > > > > > + tc->dsi = dsi; > > > > > + > > > > > + dsi->lanes = tc->num_dsi_lanes; > > > > > + dsi->format = MIPI_DSI_FMT_RGB888; > > > > > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; > > > > > + > > > > > + ret = mipi_dsi_attach(dsi); > > > > > + if (ret < 0) { > > > > > + dev_err(dev, "failed to attach dsi to host\n"); > > > > > + goto err_dsi_attach; > > > > > + } > > > > > + > > > > > + return 0; > > > > > + > > > > > +err_dsi_attach: > > > > > + mipi_dsi_device_unregister(dsi); > > > > > +err_dsi_device: > > > > > + return ret; > > > > > +} > > > > > + > > > > > +static int tc_bridge_attach(struct drm_bridge *bridge) > > > > > +{ > > > > > + struct tc_data *tc = bridge_to_tc(bridge); > > > > > + struct drm_device *drm = bridge->dev; > > > > > + int ret; > > > > > + > > > > > + /* Create LVDS connector */ > > > > > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); > > > > > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, > > > > > + DRM_MODE_CONNECTOR_LVDS); > > > > > + if (ret) > > > > > + return ret; > > > > > + > > > > > + if (tc->panel) > > > > > + drm_panel_attach(tc->panel, &tc->connector); > > > > > + > > > > > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); > > > > > + > > > > > + ret = tc358775_attach_dsi(tc); > > > > > > > > Ignored retval. > > > > > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +static const struct drm_bridge_funcs tc_bridge_funcs = { > > > > > + .attach = tc_bridge_attach, > > > > > + .pre_enable = tc_bridge_pre_enable, > > > > > + .enable = tc_bridge_enable, > > > > > + .disable = tc_bridge_disable, > > > > > + .post_disable = tc_bridge_post_disable, > > > > > +}; > > > > > + > > > > > +static const struct regmap_config tc_regmap_config = { > > > > > + .name = "tc358775", > > > > > + .reg_bits = 16, > > > > > + .val_bits = 32, > > > > > + .reg_stride = 4, > > > > > + .max_register = 0x05A8, > > > > > + .cache_type = REGCACHE_RBTREE, > > > > > + .reg_format_endian = REGMAP_ENDIAN_BIG, > > > > > + .val_format_endian = REGMAP_ENDIAN_LITTLE, > > > > > +}; > > > > > + > > > > > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) > > > > > +{ > > > > > + struct device *dev = &client->dev; > > > > > + struct tc_data *tc; > > > > > + int ret; > > > > > + unsigned int i; > > > > > + > > > > > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); > > > > > + if (!tc) > > > > > + return -ENOMEM; > > > > > + > > > > > + tc->dev = dev; > > > > > + tc->i2c = client; > > > > > + tc->status = connector_status_connected; > > > > > + > > > > > + /* port@1 is the output port */ > > > > > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); > > > > > + if (ret && ret != -ENODEV) > > > > > + return ret; > > > > You should support cases where the next device is a bridge. I recommand > > wrapping the panel in a drm_panel_bridge with drm_panel_bridge_add(), > > and then handling the next component as a bridge in all code paths. This > > will allow removing manual enable/disable of panels above, as bridge > > chaining is handled automatically. drm_panel_bridge creates a > > drm_connector, so you can drop your manual connector implementation > > here, simplifying the code. > > i am not clear on this drm_panel_bridge_add() usage, please > clarify/any reference would be helpful. See drivers/gpu/drm/bridge/lvds-codec.c for instance. Note that you should not used the *_typed() version of drm_panel_bridge_add in new drivers, you should instead use drm_panel_bridge_add() or devm_drm_panel_bridge_add(). > > > > > + > > > > > + ret = tc358775_parse_dt(dev->of_node, tc); > > > > > + if (ret) > > > > > + return ret; > > > > > + > > > > > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) > > > > > + tc->supplies[i].supply = regulator_names[i]; > > > > > + > > > > > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), > > > > > + tc->supplies); > > > > > + if (ret < 0) > > > > > + dev_err(dev, "failed to init regulator, ret=%d\n", ret); > > > > > + > > > > > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); > > > > > + if (IS_ERR(tc->stby_gpio)) { > > > > > + ret = PTR_ERR(tc->stby_gpio); > > > > > + dev_err(dev, "cannot get stby-gpio %d\n", ret); > > > > > + return ret; > > > > > + } > > > > > + > > > > > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); > > > > > + if (IS_ERR(tc->reset_gpio)) { > > > > > + ret = PTR_ERR(tc->reset_gpio); > > > > > + dev_err(dev, "cannot get reset-gpios %d\n", ret); > > > > > + return ret; > > > > > + } > > > > > + > > > > > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); > > > > > + if (IS_ERR(tc->regmap)) { > > > > > + ret = PTR_ERR(tc->regmap); > > > > > + dev_err(dev, "Failed to initialize regmap: %d\n", ret); > > > > > + return ret; > > > > > + } > > > > > + > > > > > + tc->bridge.funcs = &tc_bridge_funcs; > > > > > + tc->bridge.of_node = dev->of_node; > > > > > + drm_bridge_add(&tc->bridge); > > > > > + > > > > > + i2c_set_clientdata(client, tc); > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +static int tc_remove(struct i2c_client *client) > > > > > +{ > > > > > + struct tc_data *tc = i2c_get_clientdata(client); > > > > > + > > > > > + drm_bridge_remove(&tc->bridge); > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +static const struct i2c_device_id tc358775_i2c_ids[] = { > > > > > + { "tc358775", 0 }, > > > > > + { } > > > > > +}; > > > > > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); > > > > > + > > > > > +static const struct of_device_id tc358775_of_ids[] = { > > > > > + { .compatible = "toshiba,tc358775", }, > > > > > + { } > > > > > +}; > > > > > +MODULE_DEVICE_TABLE(of, tc358775_of_ids); > > > > > + > > > > > +static struct i2c_driver tc358775_driver = { > > > > > + .driver = { > > > > > + .name = "tc358775", > > > > > + .of_match_table = tc358775_of_ids, > > > > > + }, > > > > > + .id_table = tc358775_i2c_ids, > > > > > + .probe = tc_probe, > > > > > + .remove = tc_remove, > > > > > +}; > > > > > +module_i2c_driver(tc358775_driver); > > > > > + > > > > > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); > > > > > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); > > > > > > > > maybe better: > > > > > > > > tc358775 DSI/LVDS bridge driver > > > > > > > > > +MODULE_LICENSE("GPL v2"); -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
laurent,
Is it possible to access the data-lanes of dsi, by using d2l_in in the
bridge driver by ports funcs? because num_lanes is not accessible
outside dsi_host, not available any of the drm parameters.
dsi@1a98000 {
ports {
port@1 {
endpoint {
remote-endpoint = <&d2l_in>;
data-lanes = <0 1 2 3>;
};
};
};
};
tc_bridge: bridge@f {
status = "okay";
...
ports {
port@0 {
reg = <0>;
d2l_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
port@1 {
reg = <1>;
lvds0_out: endpoint {
remote-endpoint = <&panel_in0>;
};
};
};
};
On Thu, Mar 12, 2020 at 8:01 PM Laurent Pinchart
<laurent.pinchart@ideasonboard.com> wrote:
>
> Hi Vinay,
>
> On Wed, Mar 11, 2020 at 03:30:48PM +0530, Vinay Simha B N wrote:
> > Laurent Pinchart,
> >
> > if we want to set to jeida-18 data mapping,
> > do we need to set DATA3 with "Logic 0" LVI_L0 ?
>
> If the TC358775 supports setting unused outputs to a fixed logic level I
> think that's best, yes.
>
> > Please see reply inline.
>
> Same :-)
>
> > >
> > > On Fri, Mar 06, 2020 at 06:06:36PM +0530, Vinay Simha B N wrote:
> > > > hi andrzej,
> > > >
> > > > I had a doubt In the tc358764 driver,VP_CTRL, VP_CTRL_VSDELAY(15) is
> > > > hardcoded to 15, but this has to be dynamic based on the resolution of
> > > > panel used?
> > > >
> > > > Please see the reply inline.
> > > >
> > > > On Tue, Mar 3, 2020 at 8:39 PM Andrzej Hajda <a.hajda@samsung.com> wrote:
> > > > > On 27.02.2020 15:03, Vinay Simha BN wrote:
> > > > > > dsi2lvds tc358775 bridge driver added
> > > > > > Tested in apq8016, ifc6309 board and panel
> > > > > > auo,b101xtn01
> > > > >
> > > > > Just FYI, there exists already TC358764/5 driver for similar hw, but
> > > > > controlled via DSI bus.
> > > >
> > > > There is not much difference between these two chips, but still the
> > > > dsi read access for 775 does not works.
> > > > TC358764/5 - 800Mbps per lane, 3.2Gbps
> > > > TC358775 - 1Gbps per lane, 4Gbps.
> > > >
> > > > tc358775 chip details -
> > > > https://download.t-firefly.com/product/RK3399/Docs/Chip%20Specifications/TC358774XBG_75XBG_V1%204nm.pdf
> > > > I am able to configure the tc358775 chip by i2c, but from dsi it fails
> > > > i tried accessing the tc358775 chip by dsi using apq8016-qcom , but it
> > > > fails to read the chip id itself.
> > > >
> > > > Please suggest if you any inputs for this issue.
> > > >
> > > > https://github.com/vinaysimhabn/kernel-msm/commits/5.6.0-rc3-dsi2lvds-dsi
> > > >
> > > > [ 4.582405] tc358764 1a98000.dsi.0: read: 1408, addr: 0
> > > > [ 4.582426] tc358764 1a98000.dsi.0: ID: 0x0
> > > > [ 4.582451] tc358764 1a98000.dsi.0: error initializing bridge (-22)
> > > >
> > > > [ 4.796220] dsi_cmds2buf_tx: cmd dma tx failed, type=0x24, data0=0x80, len=4
> > > > [ 4.796244] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > > > [ 4.796266] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > > > [ 4.796288] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > > > [ 4.796310] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > > > [ 4.796319] msm_dsi_host_cmd_rx:Invalid response cmd
> > > >
> > > > > > Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
> > > > > > ---
> > > > > > .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++
> > > > >
> > > > > Bindings should be in separate patch and in yaml format.
> > > > >
> > > > > > drivers/gpu/drm/bridge/Kconfig | 10 +
> > > > > > drivers/gpu/drm/bridge/Makefile | 1 +
> > > > > > drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++
> > > > > > 4 files changed, 804 insertions(+)
> > > > > > create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt
> > > > > > create mode 100644 drivers/gpu/drm/bridge/tc358775.c
> > > > > >
> > > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt
> > > > > > new file mode 100644
> > > > > > index 0000000..c4c364d
> > > > > > --- /dev/null
> > > > > > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt
> > > > > > @@ -0,0 +1,106 @@
> > > > > > +Toshiba TC358775 DSI to LVDS bridge bindings
> > > > > > +
> > > > > > +Required properties:
> > > > > > + - compatible: "toshiba,tc358775"
> > > > > > + - reg: i2c address of the bridge, 0x0f
> > > > > > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
> > > > > > + be one of 1, 2, 3 or 4.
> > > > > > + - tc, dual-link : To configure the LVDS transmitter either
> > > > > > + as single-link or dual-link.
> > > > > > + - tc, data-format: To configure the data formats
> > > > > > + 0 for VESA standard, 1 for JEIDA standard
> > > > >
> > > > > IMO, three properties above should be received from downstream device in
> > > > > runtime, not hardcoded into DT, however I am not sure if frameworks
> > > > > support it.
> > >
> > > I assume Andrzej meant upstream device for the tc,dsi-lanes property.
> > > This should be exposed through the data-lanes property as described in
> > > media/video-interface.txt.
> >
> > data-lanes mainly used for the interfaces of the hardware.
> > example : dsi, csi
>
> Correct, so please use it to replace tc,dsi-lanes :-)
>
> > In general panels/bridges either it will be hardcoded by setting in the
> > panel driver like this dsi->lanes = 4;
> > bridge -> dsi2hdmi display/bridge/adi,adv7511.txt it wil be set by
> > adi,dsi-lanes
>
> That's a mistake in the bindings, let's not repeat it.
>
> > > The tc,dual-link property should be replaced by exposing two port nodes,
> > > one for each link, and connecting them appropriately. See
> > > display/bridge/thine,thc63lvd1024.txt for an example of DT bindings on
> > > the LVDS receiver side, and drivers/gpu/drm/rcar-du/rcar_lvds.c for an
> > > example implementation on the LVDS transmitter side.
> >
> > Can we add two port nodes though it can give only 1 output? when
> > higher resolution panel used dual_link is enabled in LVCFG
>
> Sure, you will have three ports in total, one for the DSI intput, and
> two for the two LVDS outputs. A port node maps to a physical connection,
> and there's nothing wrong with having two port nodes to describe the
> dual-link LVDS output.
>
> > > The tc,data-format property should be replaced by the data-mapping
> > > property on the downstream LVDS device (see display/panel/lvds.yaml) and
> > > queried at runtime.
> > >
> > > > > > + - vdd-supply: 1.2V LVDS Power Supply
> > > > > > + - vddio-supply: 1.8V IO Power Supply
> > > > > > + - stby-gpios: Standby pin, Low active
> > > > > > + - reset-gpios: Hardware reset, Low active
> > > > > > +
> > > > > > +Required nodes:
> > > > > > +
> > > > > > +The TC358775 has two ports. Their connections are modelled using the OF
> > > > > > +graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> > > > > > +
> > > > > > +- Video port 0 for the DSI input. The remote endpoint phandle should be a
> > > > > > + reference to a valid mipi_dsi_host device node.
> > > > > > +- Video port 1 for the LVDS output.
> > > > > > +
> > > > > > +Example:
> > > > > > +
> > > > > > + i2c@78b8000 {
> > > > > > + /* On High speed expansion */
> > > > > > + label = "HS-I2C2";
> > > > > > + status = "okay";
> > > > > > +
> > > > > > + tc_bridge: bridge@f {
> > > > > > + status = "okay";
> > > > > > +
> > > > > > + compatible = "toshiba,tc358775";
> > > > > > + reg = <0x0f>;
> > > > > > +
> > > > > > + tc,dsi-lanes = <4>;
> > > > > > + tc,dual-link = <0>;
> > > > > > + tc,data-format = <1>;
> > > > > > +
> > > > > > + vdd-supply = <&pm8916_l2>;
> > > > > > + vddio-supply = <&pm8916_l6>;
> > > > > > +
> > > > > > + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>;
> > > > > > + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>;
> > > > > > +
> > > > > > + ports {
> > > > > > + #address-cells = <1>;
> > > > > > + #size-cells = <0>;
> > > > > > +
> > > > > > + port@0 {
> > > > > > + reg = <0>;
> > > > > > + d2l_in: endpoint {
> > > > > > + remote-endpoint = <&dsi0_out>;
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > + port@1 {
> > > > > > + reg = <1>;
> > > > > > + d2l_out: endpoint {
> > > > > > + remote-endpoint = <&panel_in>;
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > + panel: auo,b101xtn01 {
> > > > > > + status = "okay";
> > > > > > + compatible = "auo,b101xtn01";
> > > > > > + power-supply = <&pm8916_l14>;
> > > > > > +
> > > > > > + port {
> > > > > > + panel_in: endpoint {
> > > > > > + remote-endpoint = <&d2l_out>;
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > + mdss@1a00000 {
> > > > > > + status = "okay";
> > > > > > +
> > > > > > + mdp@1a01000 {
> > > > > > + status = "okay";
> > > > > > + };
> > > > > > +
> > > > > > + dsi@1a98000 {
> > > > > > + status = "okay";
> > > > > > + ..
> > > > > > + ports {
> > > > > > + port@1 {
> > > > > > + dsi0_out: endpoint {
> > > > > > + remote-endpoint = <&d2l_in>;
> > > > > > + data-lanes = <0 1 2 3>;
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > + dsi-phy@1a98300 {
> > > > > > + status = "okay";
> > > > > > + ..
> > > > > > + };
> > > > > > + };
> > > > > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> > > > > > index 8397bf7..d5528fa 100644
> > > > > > --- a/drivers/gpu/drm/bridge/Kconfig
> > > > > > +++ b/drivers/gpu/drm/bridge/Kconfig
> > > > > > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767
> > > > > > ---help---
> > > > > > Toshiba TC358767 eDP bridge chip driver.
> > > > > >
> > > > > > +config DRM_TOSHIBA_TC358775
> > > > > > + tristate "Toshiba TC358775 LVDS bridge"
> > > > > > + depends on OF
> > > > > > + select DRM_KMS_HELPER
> > > > > > + select REGMAP_I2C
> > > > > > + select DRM_PANEL
> > > > > > + select DRM_MIPI_DSI
> > > > > > + ---help---
> > > > > > + Toshiba TC358775 LVDS bridge chip driver.
> > > > > > +
> > > > > > config DRM_TI_TFP410
> > > > > > tristate "TI TFP410 DVI/HDMI bridge"
> > > > > > depends on OF
> > > > > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> > > > > > index 1eb5376..9b2c512 100644
> > > > > > --- a/drivers/gpu/drm/bridge/Makefile
> > > > > > +++ b/drivers/gpu/drm/bridge/Makefile
> > > > > > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o
> > > > > > obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
> > > > > > obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
> > > > > > obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
> > > > > > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o
> > > > > > obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
> > > > > > obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
> > > > > > obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
> > > > > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c
> > > > > > new file mode 100644
> > > > > > index 0000000..3db0f49
> > > > > > --- /dev/null
> > > > > > +++ b/drivers/gpu/drm/bridge/tc358775.c
> > > > > > @@ -0,0 +1,687 @@
> > > > > > +// SPDX-License-Identifier: GPL-2.0
> > > > > > +/*
> > > > > > + * tc358775 DSI to LVDS bridge driver
> > > > > > + *
> > > > > > + * Copyright (C) 2020 InforceComputing
> > > > > > + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com>
> > > > > > + *
> > > > > > + * This program is free software; you can redistribute it and/or modify
> > > > > > + * it under the terms of the GNU General Public License as published by
> > > > > > + * the Free Software Foundation; either version 2 of the License, or
> > > > > > + * (at your option) any later version.
> > > > > > + *
> > > > > > + * This program is distributed in the hope that it will be useful,
> > > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > > > > + * GNU General Public License for more details.
> > > > >
> > > > > You can drop these statements, SPDX identifier is enough.
> > > > >
> > > > > > + */
> > > > > > +
> > > > > > +/* #define DEBUG */
> > > > > > +/* #define TC358775_DEBUG */
> > > > >
> > > > > Please remove these development leftovers.
> > > > >
> > > > > > +#include <linux/clk.h>
> > > > > > +#include <linux/device.h>
> > > > > > +#include <linux/gpio/consumer.h>
> > > > > > +#include <linux/i2c.h>
> > > > > > +#include <linux/kernel.h>
> > > > > > +#include <linux/module.h>
> > > > > > +#include <linux/regmap.h>
> > > > > > +#include <linux/slab.h>
> > > > > > +#include <linux/regulator/consumer.h>
> > > > > Alphabetic order.
> > > > > > +
> > > > > > +#include <drm/drm_mipi_dsi.h>
> > > > > > +#include <drm/drm_atomic_helper.h>
> > > > > > +#include <drm/drm_crtc_helper.h>
> > > > > > +#include <drm/drm_dp_helper.h>
> > > > > > +#include <drm/drm_of.h>
> > > > > > +#include <drm/drm_panel.h>
> > > > > > +#include <drm/drm_bridge.h>
> > > > > > +#include <drm/drm_probe_helper.h>
> > > > > ditto
> > > > > > +
> > > > > > +/* Registers */
> > > > > > +
> > > > > > +/* DSI D-PHY Layer Registers */
> > > > > > +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */
> > > > > > +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */
> > > > > > +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */
> > > > > > +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */
> > > > > > +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */
> > > > > > +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */
> > > > > > +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */
> > > > > > +#define CLW_CNTRL 0x0040 /* Clock Lane Control */
> > > > > > +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */
> > > > > > +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */
> > > > > > +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */
> > > > > > +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */
> > > > > > +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */
> > > > > > +
> > > > > > +/* DSI PPI Layer Registers */
> > > > > > +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */
> > > > > > +#define PPI_BUSYPPI 0x0108
> > > > > > +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */
> > > > > > +#define PPI_LPTXTIMECNT 0x0114
> > > > > > +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */
> > > > > > +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */
> > > > > > +
> > > > > > +/* Analog timer function enable */
> > > > > > +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */
> > > > > > +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */
> > > > > > +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */
> > > > > > +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */
> > > > > > +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */
> > > > > > +#define PPI_D0S_CLRSIPOCOUNT 0x0164
> > > > > > +
> > > > > > +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */
> > > > > > +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */
> > > > > > +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */
> > > > > > +
> > > > > > +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */
> > > > > > +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */
> > > > > > +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */
> > > > > > +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */
> > > > > > +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */
> > > > > > +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */
> > > > > > +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */
> > > > > > +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */
> > > > > > +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */
> > > > > > +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */
> > > > > > +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */
> > > > > > +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */
> > > > > > +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */
> > > > > > +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */
> > > > > > +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */
> > > > > > +
> > > > > > +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */
> > > > > > +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */
> > > > > > +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */
> > > > > > +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */
> > > > > > +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */
> > > > > > +#define DSI_BUSYDSI 0x0208
> > > > > > +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */
> > > > > > +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */
> > > > > > +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */
> > > > > > +
> > > > > > +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */
> > > > > > +#define DSI_INTMASK 0x0224 /* Interrupt Mask */
> > > > > > +#define DSI_INTCLR 0x0228 /* Interrupt Clear */
> > > > > > +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */
> > > > > > +
> > > > > > +#define DSIERRCNT 0x0300 /* DSI Error Count */
> > > > > > +#define APLCTRL 0x0400 /* Application Layer Control */
> > > > > > +#define RDPKTLN 0x0404 /* Command Read Packet Length */
> > > > > > +
> > > > > > +#define VPCTRL 0x0450 /* Video Path Control */
> > > > > > +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */
> > > > > > +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */
> > > > > > +#define VTIM1 0x045C /* Vertical Timing Control 1 */
> > > > > > +#define VTIM2 0x0460 /* Vertical Timing Control 2 */
> > > > > > +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */
> > > > > > +
> > > > > > +/* Mux Input Select for LVDS LINK Input */
> > > > > > +#define LVMX0003 0x0480 /* Bit 0 to 3 */
> > > > > > +#define LVMX0407 0x0484 /* Bit 4 to 7 */
> > > > > > +#define LVMX0811 0x0488 /* Bit 8 to 11 */
> > > > > > +#define LVMX1215 0x048C /* Bit 12 to 15 */
> > > > > > +#define LVMX1619 0x0490 /* Bit 16 to 19 */
> > > > > > +#define LVMX2023 0x0494 /* Bit 20 to 23 */
> > > > > > +#define LVMX2427 0x0498 /* Bit 24 to 27 */
> > > > > > +
> > > > > > +#define LVCFG 0x049C /* LVDS Configuration */
> > > > > > +#define LVPHY0 0x04A0 /* LVDS PHY 0 */
> > > > > > +#define LVPHY1 0x04A4 /* LVDS PHY 1 */
> > > > > > +#define SYSSTAT 0x0500 /* System Status */
> > > > > > +#define SYSRST 0x0504 /* System Reset */
> > > > > > +/* GPIO Registers */
> > > > > > +#define GPIOC 0x0520 /* GPIO Control */
> > > > > > +#define GPIOO 0x0524 /* GPIO Output */
> > > > > > +#define GPIOI 0x0528 /* GPIO Input */
> > > > > > +
> > > > > > +/* I2C Registers */
> > > > > > +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */
> > > > > > +#define I2CMADDR 0x0544 /* I2C Master Addressing */
> > > > > > +#define WDATAQ 0x0548 /* Write Data Queue */
> > > > > > +#define RDATAQ 0x054C /* Read Data Queue */
> > > > > > +
> > > > > > +/* Chip ID and Revision ID Register */
> > > > > > +#define IDREG 0x0580
> > > > > > +
> > > > > > +#define TC358775XBG_ID 0x00007500
> > > > > > +
> > > > > > +/* Debug Registers */
> > > > > > +#define DEBUG00 0x05A0 /* Debug */
> > > > > > +#define DEBUG01 0x05A4 /* LVDS Data */
> > > > > > +
> > > > > > +#define DSI_CLEN_BIT BIT(0)
> > > > > > +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */
> > > > > > +#define LVCFG_LVEN_BIT BIT(0)
> > > > > > +
> > > > > > +#define L0EN BIT(1)
> > > > > > +
> > > > > > +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000
> > > > > > +#define TC358775_VPCTRL_VSDELAY__SHIFT 20
> > > > > > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val)
> > > > >
> > > > >
> > > > > Use u32 here and below, unit32_t is mainly for userspace interactions.
> > > > >
> > > > >
> > > > > > +{
> > > > > > + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) &
> > > > > > + TC358775_VPCTRL_VSDELAY__MASK;
> > > > > > +}
> > > > > > +
> > > > > > +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100
> > > > > > +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8
> > > > > > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val)
> > > > > > +{
> > > > > > + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) &
> > > > > > + TC358775_VPCTRL_OPXLFMT__MASK;
> > > > > > +}
> > > > > > +
> > > > > > +#define TC358775_VPCTRL_MSF__MASK 0x00000001
> > > > > > +#define TC358775_VPCTRL_MSF__SHIFT 0
> > > > > > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val)
> > > > > > +{
> > > > > > + return ((val) << TC358775_VPCTRL_MSF__SHIFT) &
> > > > > > + TC358775_VPCTRL_MSF__MASK;
> > > > > > +}
> > > > > > +
> > > > > > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0
> > > > > > +#define TC358775_LVCFG_PCLKDIV__SHIFT 4
> > > > > > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val)
> > > > > > +{
> > > > > > + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) &
> > > > > > + TC358775_LVCFG_PCLKDIV__MASK;
> > > > > > +}
> > > > > > +
> > > > > > +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002
> > > > > > +#define TC358775_LVCFG_LVDLINK__SHIFT 0
> > > > > > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val)
> > > > > > +{
> > > > > > + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) &
> > > > > > + TC358775_LVCFG_LVDLINK__MASK;
> > > > > > +}
> > > > > > +
> > > > > > +static const struct reg_sequence tc_fixed_registers[] = {
> > > > > > + { 0x013C, 0x00040006 },
> > > > > > + { 0x0114, 0x00000004 },
> > > > > > + { 0x0164, 0x00000003 },
> > > > > > + { 0x0168, 0x00000003 },
> > > > > > + { 0x016C, 0x00000003 },
> > > > > > + { 0x0170, 0x00000003 },
> > > > >
> > > > > use macros instead of magic numbers.
> > > > >
> > > > > > +};
> > > > > > +
> > > > > > +static const struct reg_sequence tc_vesa_data_format_registers[] = {
> > > > > > + { 0x0480, 0x03020100 },
> > > > > > + { 0x0484, 0x08050704 },
> > > > > > + { 0x0488, 0x0F0E0A09 },
> > > > > > + { 0x048C, 0x100D0C0B },
> > > > > > + { 0x0490, 0x12111716 },
> > > > > > + { 0x0494, 0x1B151413 },
> > > > > > + { 0x0498, 0x061A1918 },
> > > > > ditto
> > > > > > +};
> > > > > > +
> > > > > > +static const char * const regulator_names[] = {
> > > > > > + "vdd",
> > > > > > + "vddio"
> > > > > > +};
> > > > > > +
> > > > > > +struct tc_data {
> > > > > > + struct i2c_client *i2c;
> > > > > > +
> > > > > > + struct device *dev;
> > > > > > + struct regmap *regmap;
> > > > > > +
> > > > > > + struct drm_bridge bridge;
> > > > > > + struct drm_connector connector;
> > > > > > + struct drm_panel *panel;
> > > > > > +
> > > > > > + enum drm_connector_status status;
> > > > > unused field
> > status used in tc->status = connector_status_connected;
> > > > > > + struct device_node *host_node;
> > > > > > + struct mipi_dsi_device *dsi;
> > > > > > + u8 num_dsi_lanes;
> > > > > > +
> > > > > > + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
> > > > > > + struct gpio_desc *reset_gpio;
> > > > > > + struct gpio_desc *stby_gpio;
> > > > > > + u32 rev;
> > > > > > + u8 dual_link; /* single-link or dual-link */
> > > > > > + u8 data_format; /* VESA or JEIDA */
> > > > > > +};
> > > > > > +
> > > > > > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b)
> > > > > > +{
> > > > > > + return container_of(b, struct tc_data, bridge);
> > > > > > +}
> > > > > > +
> > > > > > +static inline struct tc_data *connector_to_tc(struct drm_connector *c)
> > > > > > +{
> > > > > > + return container_of(c, struct tc_data, connector);
> > > > > > +}
> > > > > > +
> > > > > > +static void tc_bridge_pre_enable(struct drm_bridge *bridge)
> > > > > > +{
> > > > > > + struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > + struct device *dev = &tc->dsi->dev;
> > > > > > + int ret;
> > > > > > +
> > > > > > + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies);
> > > > > > + if (ret < 0) {
> > > > > > + dev_err(dev, "regulator enable failed, %d\n", ret);
> > > > > > + return;
> > > > > > + }
> > > > > > + mdelay(10);
> > >
> > > You should consider usleep_range() instead of mdelay() for large delays.
> > >
> > > > > > +
> > > > > > + gpiod_set_value(tc->stby_gpio, 0);
> > > > > > + mdelay(10);
> > > > > > +
> > > > > > + gpiod_set_value(tc->reset_gpio, 0);
> > > > > > + ndelay(50);
> > > > > > +
> > > > > > + drm_panel_prepare(tc->panel);
> > > > > > +}
> > > > > > +
> > > > > > +static void tc_bridge_disable(struct drm_bridge *bridge)
> > > > > > +{
> > > > > > + struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > + struct device *dev = &tc->dsi->dev;
> > > > > > + int ret;
> > > > > > +
> > > > > > + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies);
> > > > > > + if (ret < 0)
> > > > > > + dev_err(dev, "regulator disable failed, %d\n", ret);
> > > > > > + mdelay(10);
> > > > > > +
> > > > > > + gpiod_set_value(tc->stby_gpio, 1);
> > > > > > + mdelay(10);
> > > > > > +
> > > > > > + gpiod_set_value(tc->reset_gpio, 1);
> > > > > > + ndelay(50);
> > > > > > +
> > > > > > + drm_panel_disable(tc->panel);
> > > > >
> > > > > I suspect the order should be different - ie reverse to the one pre_enable.
> > - as per the datasheet it is not in reverse order
> >
> > > > >
> > > > > Moreover since it reverts pre_enable it should be put into post_disable
> > > > > (except drm_panel_disable).
> > > > >
> > > > > > +}
> > > > > > +
> > > > > > +static void tc_bridge_post_disable(struct drm_bridge *bridge)
> > > > > > +{
> > > > > > + struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > +
> > > > > > + drm_panel_unprepare(tc->panel);
> > > > > > +}
> > > > > > +
> > > > > > +#ifdef TC358775_DEBUG
> > > > > > +static u32 d2l_read(struct tc_data *tc, u16 reg)
> > > > > > +{
> > > > > > + int ret;
> > > > > > + u32 data;
> > > > > > +
> > > > > > + ret = regmap_bulk_read(tc->regmap, reg, &data, 1);
> > > > > > + if (ret)
> > > > > > + return ret;
> > > > > > +
> > > > > > + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data);
> > > > > > +
> > > > > > + return data;
> > > > > > +}
> > > > > > +#endif
> > > > >
> > > > > I guess this leftover can be removed as well.
> > > > >
> > > > > > +
> > > > > > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data)
> > > > > > +{
> > > > > > + int ret = 0;
> > > > > > +
> > > > > > + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1);
> > > > > > +
> > > > > > +#ifdef TC358775_DEBUG
> > > > > > + d2l_read(tc, reg);
> > > > > > +#endif
> > > > > > + return ret;
> > > > > > +}
> > > > > > +
> > > > > > +static void tc_bridge_enable(struct drm_bridge *bridge)
> > > > > > +{
> > > > > > + struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > + int ret;
> > > > > > + u32 hbpr, hpw, htime1, hfpr, hsize, htime2;
> > > > > > + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2;
> > > > > > + u32 val = 0;
> > > > > > + struct drm_display_mode *mode;
> > > > > > +
> > > > > > + mode = &bridge->encoder->crtc->state->adjusted_mode;
> > > > > > +
> > > > > > + hbpr = 0;
> > > > > > + hpw = mode->hsync_end - mode->hsync_start;
> > > > > > + vbpr = 0;
> > > > > > + vpw = mode->vsync_end - mode->vsync_start;
> > > > > > +
> > > > > > + htime1 = (hbpr << 16) + hpw;
> > > > > > + vtime1 = (vbpr << 16) + vpw;
> > > > > > +
> > > > > > + hfpr = mode->hsync_start - mode->hdisplay;
> > > > > > + hsize = mode->hdisplay;
> > > > > > + vfpr = mode->vsync_start - mode->vdisplay;
> > > > > > + vsize = mode->vdisplay;
> > > > > > +
> > > > > > + htime2 = (hfpr << 16) + hsize;
> > > > > > + vtime2 = (vfpr << 16) + vsize;
> > > > > > +
> > > > > > + ret = regmap_read(tc->regmap, IDREG, &tc->rev);
> > > > > > + if (ret) {
> > > > > > + dev_err(tc->dev, "can not read device ID: %d\n", ret);
> > > > > > + return;
> > > > > > + }
> > > > > > + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev);
> > > > > > +
> > > > > > + d2l_write(tc, SYSRST, 0x000000FF);
> > > > > > + mdelay(30);
> > > > > > +
> > > > > > + ret = regmap_register_patch(tc->regmap,
> > > > > > + tc_fixed_registers,
> > > > > > + ARRAY_SIZE(tc_fixed_registers));
> > > > > > + if (ret)
> > > > > > + return;
> > > > > > +
> > > > > > + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT;
> > > > > > + d2l_write(tc, PPI_LANEENABLE, val);
> > > > > > + d2l_write(tc, DSI_LANEENABLE, val);
> > > > > > +
> > > > > > + d2l_write(tc, PPI_STARTPPI, 0x00000001);
> > > > > > + d2l_write(tc, DSI_STARTDSI, 0x00000001);
> > > > > > +
> > > > > > + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value
> > > >
> > > > Any suggestion how to set dynamic value for Vsyncdelay?
> > > >
> > > > > > +
> > > > > > + if (tc->connector.display_info.bpc == 8) {/* RGB888 */
> > > > > > + val |= TC358775_VPCTRL_OPXLFMT(1);
> > > > > > + d2l_write(tc, VPCTRL, val);
> > > > > > + } else { /* RGB666 */
> > > > > > + val |= TC358775_VPCTRL_MSF(1);
> > > > > > + d2l_write(tc, VPCTRL, val);
> > > > > > + }
> > > > > > +
> > > > > > + d2l_write(tc, HTIM1, htime1);
> > > > > > + d2l_write(tc, VTIM1, vtime1);
> > > > > > + d2l_write(tc, HTIM2, htime2);
> > > > > > + d2l_write(tc, VTIM2, vtime2);
> > > > > > +
> > > > > > + d2l_write(tc, VFUEN, 0x00000001);
> > > > > > + d2l_write(tc, SYSRST, 0x00000004);
> > > > > > + d2l_write(tc, LVPHY0, 0x00040006);
> > > > > > +
> > > > > > + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */
> > > > > > + ret = regmap_register_patch
> > > > > > + (tc->regmap,
> > > > > > + tc_vesa_data_format_registers,
> > > > > > + ARRAY_SIZE(tc_vesa_data_format_registers));
> > > > > > + if (ret)
> > > > > > + return;
> > > > > > + }
> > > > > > +
> > > > > > + d2l_write(tc, VFUEN, 0x00000001);
> > > > > > +
> > > > > > + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT;
> > > > > > + if (tc->dual_link)
> > > > > > + val |= TC358775_LVCFG_LVDLINK(1);
> > > > > > +
> > > > > > + d2l_write(tc, LVCFG, val);
> > > > > > +
> > > > > > + drm_panel_enable(tc->panel);
> > > > > > +}
> > > > > > +
> > > > > > +static int tc_connector_get_modes(struct drm_connector *connector)
> > > > > > +{
> > > > > > + struct tc_data *tc = connector_to_tc(connector);
> > > > > > + struct edid *edid;
> > > > > > + unsigned int count;
> > > > > > +
> > > > > > + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) {
> > > > > > + count = tc->panel->funcs->get_modes(tc->panel, connector);
> > > > > > + if (count > 0)
> > > > > > + return count;
> > > > > > + }
> > > > > > +
> > > > > > + edid = drm_get_edid(connector, tc->i2c->adapter);
> > > > > > + if (!edid)
> > > > > > + return 0;
> > > > > > +
> > > > > > + drm_connector_update_edid_property(connector, edid);
> > > > > > + count = drm_add_edid_modes(connector, edid);
> > > > > > + kfree(edid);
> > > > > > +
> > > > > > + return count;
> > > > > > +}
> > > > > > +
> > > > > > +static int tc_connector_mode_valid(struct drm_connector *connector,
> > > > > > + struct drm_display_mode *mode)
> > > > > > +{
> > > > > > + struct tc_data *tc = connector_to_tc(connector);
> > > > > > +
> > > > > > + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */
> > > > > > + if ((mode->clock > 135000 && tc->dual_link == 0) ||
> > > > > > + (mode->clock > 270000 && tc->dual_link == 1))
> > > > > > + return MODE_CLOCK_HIGH;
> > > > > > +
> > > > > > + return MODE_OK;
> > > > > > +}
> > >
> > > This should be replaced by the bridge .mode_valid() operation, as it's
> > > related to the bridge, not the connector.
> > >
> > > > > > +
> > > > > > +static struct drm_encoder *
> > > > > > +tc_connector_best_encoder(struct drm_connector *connector)
> > > > > > +{
> > > > > > + struct tc_data *tc = connector_to_tc(connector);
> > > > > > +
> > > > > > + return tc->bridge.encoder;
> > > > > > +}
> > > > > > +
> > > > > > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = {
> > > > > > + .get_modes = tc_connector_get_modes,
> > > > > > + .mode_valid = tc_connector_mode_valid,
> > > > > > + .best_encoder = tc_connector_best_encoder,
> > > > > > +};
> > > > > > +
> > > > > > +static const struct drm_connector_funcs tc_connector_funcs = {
> > > > > > + .fill_modes = drm_helper_probe_single_connector_modes,
> > > > > > + .destroy = drm_connector_cleanup,
> > > > > > + .reset = drm_atomic_helper_connector_reset,
> > > > > > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> > > > > > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> > > > > > +};
> > > > > > +
> > > > > > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc)
> > > > > > +{
> > > > > > + u32 num_lanes;
> > > > > > + u8 dual_link, data_format;
> > > > > > +
> > > > > > + of_property_read_u8(np, "tc,dual-link", &dual_link);
> > > > > > + of_property_read_u8(np, "tc,data-format", &data_format);
> > > > > > + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes);
> > > > > > +
> > > > > > + if (num_lanes < 1 || num_lanes > 4)
> > > > > > + return -EINVAL;
> > > > > > +
> > > > > > + tc->num_dsi_lanes = num_lanes;
> > > > > > + tc->dual_link = dual_link;
> > > > > > + tc->data_format = data_format;
> > > > > > +
> > > > > > + tc->host_node = of_graph_get_remote_node(np, 0, 0);
> > > > > > + if (!tc->host_node)
> > > > > > + return -ENODEV;
> > > > > > +
> > > > > > + of_node_put(tc->host_node);
> > > > > > +
> > > > > > + return 0;
> > > > > > +}
> > > > > > +
> > > > > > +int tc358775_attach_dsi(struct tc_data *tc)
> > > > > > +{
> > > > > > + struct device *dev = &tc->i2c->dev;
> > > > > > + struct mipi_dsi_host *host;
> > > > > > + struct mipi_dsi_device *dsi;
> > > > > > + int ret = 0;
> > > > > > + const struct mipi_dsi_device_info info = { .type = "tc358775",
> > > > > > + .channel = 0,
> > > > > > + .node = NULL,
> > > > > > + };
> > > > > > +
> > > > > > + host = of_find_mipi_dsi_host_by_node(tc->host_node);
> > > > > > + if (!host) {
> > > > > > + dev_err(dev, "failed to find dsi host\n");
> > > > > > + return -EPROBE_DEFER;
> > > > > > + }
> > > > > > +
> > > > > > + dsi = mipi_dsi_device_register_full(host, &info);
> > > > > > + if (IS_ERR(dsi)) {
> > > > > > + dev_err(dev, "failed to create dsi device\n");
> > > > > > + ret = PTR_ERR(dsi);
> > > > > > + goto err_dsi_device;
> > > > > > + }
> > > > > > +
> > > > > > + tc->dsi = dsi;
> > > > > > +
> > > > > > + dsi->lanes = tc->num_dsi_lanes;
> > > > > > + dsi->format = MIPI_DSI_FMT_RGB888;
> > > > > > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
> > > > > > +
> > > > > > + ret = mipi_dsi_attach(dsi);
> > > > > > + if (ret < 0) {
> > > > > > + dev_err(dev, "failed to attach dsi to host\n");
> > > > > > + goto err_dsi_attach;
> > > > > > + }
> > > > > > +
> > > > > > + return 0;
> > > > > > +
> > > > > > +err_dsi_attach:
> > > > > > + mipi_dsi_device_unregister(dsi);
> > > > > > +err_dsi_device:
> > > > > > + return ret;
> > > > > > +}
> > > > > > +
> > > > > > +static int tc_bridge_attach(struct drm_bridge *bridge)
> > > > > > +{
> > > > > > + struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > + struct drm_device *drm = bridge->dev;
> > > > > > + int ret;
> > > > > > +
> > > > > > + /* Create LVDS connector */
> > > > > > + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs);
> > > > > > + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs,
> > > > > > + DRM_MODE_CONNECTOR_LVDS);
> > > > > > + if (ret)
> > > > > > + return ret;
> > > > > > +
> > > > > > + if (tc->panel)
> > > > > > + drm_panel_attach(tc->panel, &tc->connector);
> > > > > > +
> > > > > > + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder);
> > > > > > +
> > > > > > + ret = tc358775_attach_dsi(tc);
> > > > >
> > > > > Ignored retval.
> > > > >
> > > > > > +
> > > > > > + return 0;
> > > > > > +}
> > > > > > +
> > > > > > +static const struct drm_bridge_funcs tc_bridge_funcs = {
> > > > > > + .attach = tc_bridge_attach,
> > > > > > + .pre_enable = tc_bridge_pre_enable,
> > > > > > + .enable = tc_bridge_enable,
> > > > > > + .disable = tc_bridge_disable,
> > > > > > + .post_disable = tc_bridge_post_disable,
> > > > > > +};
> > > > > > +
> > > > > > +static const struct regmap_config tc_regmap_config = {
> > > > > > + .name = "tc358775",
> > > > > > + .reg_bits = 16,
> > > > > > + .val_bits = 32,
> > > > > > + .reg_stride = 4,
> > > > > > + .max_register = 0x05A8,
> > > > > > + .cache_type = REGCACHE_RBTREE,
> > > > > > + .reg_format_endian = REGMAP_ENDIAN_BIG,
> > > > > > + .val_format_endian = REGMAP_ENDIAN_LITTLE,
> > > > > > +};
> > > > > > +
> > > > > > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
> > > > > > +{
> > > > > > + struct device *dev = &client->dev;
> > > > > > + struct tc_data *tc;
> > > > > > + int ret;
> > > > > > + unsigned int i;
> > > > > > +
> > > > > > + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
> > > > > > + if (!tc)
> > > > > > + return -ENOMEM;
> > > > > > +
> > > > > > + tc->dev = dev;
> > > > > > + tc->i2c = client;
> > > > > > + tc->status = connector_status_connected;
> > > > > > +
> > > > > > + /* port@1 is the output port */
> > > > > > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL);
> > > > > > + if (ret && ret != -ENODEV)
> > > > > > + return ret;
> > >
> > > You should support cases where the next device is a bridge. I recommand
> > > wrapping the panel in a drm_panel_bridge with drm_panel_bridge_add(),
> > > and then handling the next component as a bridge in all code paths. This
> > > will allow removing manual enable/disable of panels above, as bridge
> > > chaining is handled automatically. drm_panel_bridge creates a
> > > drm_connector, so you can drop your manual connector implementation
> > > here, simplifying the code.
> >
> > i am not clear on this drm_panel_bridge_add() usage, please
> > clarify/any reference would be helpful.
>
> See drivers/gpu/drm/bridge/lvds-codec.c for instance. Note that you
> should not used the *_typed() version of drm_panel_bridge_add in new
> drivers, you should instead use drm_panel_bridge_add() or
> devm_drm_panel_bridge_add().
>
> > > > > > +
> > > > > > + ret = tc358775_parse_dt(dev->of_node, tc);
> > > > > > + if (ret)
> > > > > > + return ret;
> > > > > > +
> > > > > > + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++)
> > > > > > + tc->supplies[i].supply = regulator_names[i];
> > > > > > +
> > > > > > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies),
> > > > > > + tc->supplies);
> > > > > > + if (ret < 0)
> > > > > > + dev_err(dev, "failed to init regulator, ret=%d\n", ret);
> > > > > > +
> > > > > > + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH);
> > > > > > + if (IS_ERR(tc->stby_gpio)) {
> > > > > > + ret = PTR_ERR(tc->stby_gpio);
> > > > > > + dev_err(dev, "cannot get stby-gpio %d\n", ret);
> > > > > > + return ret;
> > > > > > + }
> > > > > > +
> > > > > > + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> > > > > > + if (IS_ERR(tc->reset_gpio)) {
> > > > > > + ret = PTR_ERR(tc->reset_gpio);
> > > > > > + dev_err(dev, "cannot get reset-gpios %d\n", ret);
> > > > > > + return ret;
> > > > > > + }
> > > > > > +
> > > > > > + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config);
> > > > > > + if (IS_ERR(tc->regmap)) {
> > > > > > + ret = PTR_ERR(tc->regmap);
> > > > > > + dev_err(dev, "Failed to initialize regmap: %d\n", ret);
> > > > > > + return ret;
> > > > > > + }
> > > > > > +
> > > > > > + tc->bridge.funcs = &tc_bridge_funcs;
> > > > > > + tc->bridge.of_node = dev->of_node;
> > > > > > + drm_bridge_add(&tc->bridge);
> > > > > > +
> > > > > > + i2c_set_clientdata(client, tc);
> > > > > > +
> > > > > > + return 0;
> > > > > > +}
> > > > > > +
> > > > > > +static int tc_remove(struct i2c_client *client)
> > > > > > +{
> > > > > > + struct tc_data *tc = i2c_get_clientdata(client);
> > > > > > +
> > > > > > + drm_bridge_remove(&tc->bridge);
> > > > > > +
> > > > > > + return 0;
> > > > > > +}
> > > > > > +
> > > > > > +static const struct i2c_device_id tc358775_i2c_ids[] = {
> > > > > > + { "tc358775", 0 },
> > > > > > + { }
> > > > > > +};
> > > > > > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids);
> > > > > > +
> > > > > > +static const struct of_device_id tc358775_of_ids[] = {
> > > > > > + { .compatible = "toshiba,tc358775", },
> > > > > > + { }
> > > > > > +};
> > > > > > +MODULE_DEVICE_TABLE(of, tc358775_of_ids);
> > > > > > +
> > > > > > +static struct i2c_driver tc358775_driver = {
> > > > > > + .driver = {
> > > > > > + .name = "tc358775",
> > > > > > + .of_match_table = tc358775_of_ids,
> > > > > > + },
> > > > > > + .id_table = tc358775_i2c_ids,
> > > > > > + .probe = tc_probe,
> > > > > > + .remove = tc_remove,
> > > > > > +};
> > > > > > +module_i2c_driver(tc358775_driver);
> > > > > > +
> > > > > > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>");
> > > > > > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver");
> > > > >
> > > > > maybe better:
> > > > >
> > > > > tc358775 DSI/LVDS bridge driver
> > > > >
> > > > > > +MODULE_LICENSE("GPL v2");
>
> --
> Regards,
>
> Laurent Pinchart
--
regards,
vinaysimha
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt new file mode 100644 index 0000000..c4c364d --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt @@ -0,0 +1,106 @@ +Toshiba TC358775 DSI to LVDS bridge bindings + +Required properties: + - compatible: "toshiba,tc358775" + - reg: i2c address of the bridge, 0x0f + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should + be one of 1, 2, 3 or 4. + - tc, dual-link : To configure the LVDS transmitter either + as single-link or dual-link. + - tc, data-format: To configure the data formats + 0 for VESA standard, 1 for JEIDA standard + - vdd-supply: 1.2V LVDS Power Supply + - vddio-supply: 1.8V IO Power Supply + - stby-gpios: Standby pin, Low active + - reset-gpios: Hardware reset, Low active + +Required nodes: + +The TC358775 has two ports. Their connections are modelled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for the DSI input. The remote endpoint phandle should be a + reference to a valid mipi_dsi_host device node. +- Video port 1 for the LVDS output. + +Example: + + i2c@78b8000 { + /* On High speed expansion */ + label = "HS-I2C2"; + status = "okay"; + + tc_bridge: bridge@f { + status = "okay"; + + compatible = "toshiba,tc358775"; + reg = <0x0f>; + + tc,dsi-lanes = <4>; + tc,dual-link = <0>; + tc,data-format = <1>; + + vdd-supply = <&pm8916_l2>; + vddio-supply = <&pm8916_l6>; + + stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>; + reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + d2l_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + d2l_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; + }; + + panel: auo,b101xtn01 { + status = "okay"; + compatible = "auo,b101xtn01"; + power-supply = <&pm8916_l14>; + + port { + panel_in: endpoint { + remote-endpoint = <&d2l_out>; + }; + }; + }; + + mdss@1a00000 { + status = "okay"; + + mdp@1a01000 { + status = "okay"; + }; + + dsi@1a98000 { + status = "okay"; + .. + ports { + port@1 { + dsi0_out: endpoint { + remote-endpoint = <&d2l_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; + + dsi-phy@1a98300 { + status = "okay"; + .. + }; + }; diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index 8397bf7..d5528fa 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767 ---help--- Toshiba TC358767 eDP bridge chip driver. +config DRM_TOSHIBA_TC358775 + tristate "Toshiba TC358775 LVDS bridge" + depends on OF + select DRM_KMS_HELPER + select REGMAP_I2C + select DRM_PANEL + select DRM_MIPI_DSI + ---help--- + Toshiba TC358775 LVDS bridge chip driver. + config DRM_TI_TFP410 tristate "TI TFP410 DVI/HDMI bridge" depends on OF diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index 1eb5376..9b2c512 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c new file mode 100644 index 0000000..3db0f49 --- /dev/null +++ b/drivers/gpu/drm/bridge/tc358775.c @@ -0,0 +1,687 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * tc358775 DSI to LVDS bridge driver + * + * Copyright (C) 2020 InforceComputing + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/* #define DEBUG */ +/* #define TC358775_DEBUG */ +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <linux/regulator/consumer.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_of.h> +#include <drm/drm_panel.h> +#include <drm/drm_bridge.h> +#include <drm/drm_probe_helper.h> + +/* Registers */ + +/* DSI D-PHY Layer Registers */ +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */ +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */ +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */ +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */ +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */ +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */ +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */ +#define CLW_CNTRL 0x0040 /* Clock Lane Control */ +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */ +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */ +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */ +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */ +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */ + +/* DSI PPI Layer Registers */ +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */ +#define PPI_BUSYPPI 0x0108 +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */ +#define PPI_LPTXTIMECNT 0x0114 +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */ +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */ + +/* Analog timer function enable */ +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */ +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */ +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */ +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */ +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */ +#define PPI_D0S_CLRSIPOCOUNT 0x0164 + +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */ +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */ +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */ + +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */ +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */ +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */ +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */ +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */ +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */ +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */ +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */ +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */ +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */ +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */ +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */ +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */ +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */ +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */ + +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */ +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */ +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */ +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */ +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */ +#define DSI_BUSYDSI 0x0208 +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */ +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */ +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */ + +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */ +#define DSI_INTMASK 0x0224 /* Interrupt Mask */ +#define DSI_INTCLR 0x0228 /* Interrupt Clear */ +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */ + +#define DSIERRCNT 0x0300 /* DSI Error Count */ +#define APLCTRL 0x0400 /* Application Layer Control */ +#define RDPKTLN 0x0404 /* Command Read Packet Length */ + +#define VPCTRL 0x0450 /* Video Path Control */ +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */ +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */ +#define VTIM1 0x045C /* Vertical Timing Control 1 */ +#define VTIM2 0x0460 /* Vertical Timing Control 2 */ +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */ + +/* Mux Input Select for LVDS LINK Input */ +#define LVMX0003 0x0480 /* Bit 0 to 3 */ +#define LVMX0407 0x0484 /* Bit 4 to 7 */ +#define LVMX0811 0x0488 /* Bit 8 to 11 */ +#define LVMX1215 0x048C /* Bit 12 to 15 */ +#define LVMX1619 0x0490 /* Bit 16 to 19 */ +#define LVMX2023 0x0494 /* Bit 20 to 23 */ +#define LVMX2427 0x0498 /* Bit 24 to 27 */ + +#define LVCFG 0x049C /* LVDS Configuration */ +#define LVPHY0 0x04A0 /* LVDS PHY 0 */ +#define LVPHY1 0x04A4 /* LVDS PHY 1 */ +#define SYSSTAT 0x0500 /* System Status */ +#define SYSRST 0x0504 /* System Reset */ +/* GPIO Registers */ +#define GPIOC 0x0520 /* GPIO Control */ +#define GPIOO 0x0524 /* GPIO Output */ +#define GPIOI 0x0528 /* GPIO Input */ + +/* I2C Registers */ +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */ +#define I2CMADDR 0x0544 /* I2C Master Addressing */ +#define WDATAQ 0x0548 /* Write Data Queue */ +#define RDATAQ 0x054C /* Read Data Queue */ + +/* Chip ID and Revision ID Register */ +#define IDREG 0x0580 + +#define TC358775XBG_ID 0x00007500 + +/* Debug Registers */ +#define DEBUG00 0x05A0 /* Debug */ +#define DEBUG01 0x05A4 /* LVDS Data */ + +#define DSI_CLEN_BIT BIT(0) +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */ +#define LVCFG_LVEN_BIT BIT(0) + +#define L0EN BIT(1) + +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val) +{ + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) & + TC358775_VPCTRL_VSDELAY__MASK; +} + +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val) +{ + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) & + TC358775_VPCTRL_OPXLFMT__MASK; +} + +#define TC358775_VPCTRL_MSF__MASK 0x00000001 +#define TC358775_VPCTRL_MSF__SHIFT 0 +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val) +{ + return ((val) << TC358775_VPCTRL_MSF__SHIFT) & + TC358775_VPCTRL_MSF__MASK; +} + +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val) +{ + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) & + TC358775_LVCFG_PCLKDIV__MASK; +} + +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 +#define TC358775_LVCFG_LVDLINK__SHIFT 0 +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val) +{ + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) & + TC358775_LVCFG_LVDLINK__MASK; +} + +static const struct reg_sequence tc_fixed_registers[] = { + { 0x013C, 0x00040006 }, + { 0x0114, 0x00000004 }, + { 0x0164, 0x00000003 }, + { 0x0168, 0x00000003 }, + { 0x016C, 0x00000003 }, + { 0x0170, 0x00000003 }, +}; + +static const struct reg_sequence tc_vesa_data_format_registers[] = { + { 0x0480, 0x03020100 }, + { 0x0484, 0x08050704 }, + { 0x0488, 0x0F0E0A09 }, + { 0x048C, 0x100D0C0B }, + { 0x0490, 0x12111716 }, + { 0x0494, 0x1B151413 }, + { 0x0498, 0x061A1918 }, +}; + +static const char * const regulator_names[] = { + "vdd", + "vddio" +}; + +struct tc_data { + struct i2c_client *i2c; + + struct device *dev; + struct regmap *regmap; + + struct drm_bridge bridge; + struct drm_connector connector; + struct drm_panel *panel; + + enum drm_connector_status status; + struct device_node *host_node; + struct mipi_dsi_device *dsi; + u8 num_dsi_lanes; + + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; + struct gpio_desc *reset_gpio; + struct gpio_desc *stby_gpio; + u32 rev; + u8 dual_link; /* single-link or dual-link */ + u8 data_format; /* VESA or JEIDA */ +}; + +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) +{ + return container_of(b, struct tc_data, bridge); +} + +static inline struct tc_data *connector_to_tc(struct drm_connector *c) +{ + return container_of(c, struct tc_data, connector); +} + +static void tc_bridge_pre_enable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + struct device *dev = &tc->dsi->dev; + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies); + if (ret < 0) { + dev_err(dev, "regulator enable failed, %d\n", ret); + return; + } + mdelay(10); + + gpiod_set_value(tc->stby_gpio, 0); + mdelay(10); + + gpiod_set_value(tc->reset_gpio, 0); + ndelay(50); + + drm_panel_prepare(tc->panel); +} + +static void tc_bridge_disable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + struct device *dev = &tc->dsi->dev; + int ret; + + ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies); + if (ret < 0) + dev_err(dev, "regulator disable failed, %d\n", ret); + mdelay(10); + + gpiod_set_value(tc->stby_gpio, 1); + mdelay(10); + + gpiod_set_value(tc->reset_gpio, 1); + ndelay(50); + + drm_panel_disable(tc->panel); +} + +static void tc_bridge_post_disable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + + drm_panel_unprepare(tc->panel); +} + +#ifdef TC358775_DEBUG +static u32 d2l_read(struct tc_data *tc, u16 reg) +{ + int ret; + u32 data; + + ret = regmap_bulk_read(tc->regmap, reg, &data, 1); + if (ret) + return ret; + + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data); + + return data; +} +#endif + +static int d2l_write(struct tc_data *tc, u16 reg, u32 data) +{ + int ret = 0; + + ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1); + +#ifdef TC358775_DEBUG + d2l_read(tc, reg); +#endif + return ret; +} + +static void tc_bridge_enable(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + int ret; + u32 hbpr, hpw, htime1, hfpr, hsize, htime2; + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; + u32 val = 0; + struct drm_display_mode *mode; + + mode = &bridge->encoder->crtc->state->adjusted_mode; + + hbpr = 0; + hpw = mode->hsync_end - mode->hsync_start; + vbpr = 0; + vpw = mode->vsync_end - mode->vsync_start; + + htime1 = (hbpr << 16) + hpw; + vtime1 = (vbpr << 16) + vpw; + + hfpr = mode->hsync_start - mode->hdisplay; + hsize = mode->hdisplay; + vfpr = mode->vsync_start - mode->vdisplay; + vsize = mode->vdisplay; + + htime2 = (hfpr << 16) + hsize; + vtime2 = (vfpr << 16) + vsize; + + ret = regmap_read(tc->regmap, IDREG, &tc->rev); + if (ret) { + dev_err(tc->dev, "can not read device ID: %d\n", ret); + return; + } + pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev); + + d2l_write(tc, SYSRST, 0x000000FF); + mdelay(30); + + ret = regmap_register_patch(tc->regmap, + tc_fixed_registers, + ARRAY_SIZE(tc_fixed_registers)); + if (ret) + return; + + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT; + d2l_write(tc, PPI_LANEENABLE, val); + d2l_write(tc, DSI_LANEENABLE, val); + + d2l_write(tc, PPI_STARTPPI, 0x00000001); + d2l_write(tc, DSI_STARTDSI, 0x00000001); + + val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value + + if (tc->connector.display_info.bpc == 8) {/* RGB888 */ + val |= TC358775_VPCTRL_OPXLFMT(1); + d2l_write(tc, VPCTRL, val); + } else { /* RGB666 */ + val |= TC358775_VPCTRL_MSF(1); + d2l_write(tc, VPCTRL, val); + } + + d2l_write(tc, HTIM1, htime1); + d2l_write(tc, VTIM1, vtime1); + d2l_write(tc, HTIM2, htime2); + d2l_write(tc, VTIM2, vtime2); + + d2l_write(tc, VFUEN, 0x00000001); + d2l_write(tc, SYSRST, 0x00000004); + d2l_write(tc, LVPHY0, 0x00040006); + + if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */ + ret = regmap_register_patch + (tc->regmap, + tc_vesa_data_format_registers, + ARRAY_SIZE(tc_vesa_data_format_registers)); + if (ret) + return; + } + + d2l_write(tc, VFUEN, 0x00000001); + + val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT; + if (tc->dual_link) + val |= TC358775_LVCFG_LVDLINK(1); + + d2l_write(tc, LVCFG, val); + + drm_panel_enable(tc->panel); +} + +static int tc_connector_get_modes(struct drm_connector *connector) +{ + struct tc_data *tc = connector_to_tc(connector); + struct edid *edid; + unsigned int count; + + if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { + count = tc->panel->funcs->get_modes(tc->panel, connector); + if (count > 0) + return count; + } + + edid = drm_get_edid(connector, tc->i2c->adapter); + if (!edid) + return 0; + + drm_connector_update_edid_property(connector, edid); + count = drm_add_edid_modes(connector, edid); + kfree(edid); + + return count; +} + +static int tc_connector_mode_valid(struct drm_connector *connector, + struct drm_display_mode *mode) +{ + struct tc_data *tc = connector_to_tc(connector); + + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ + if ((mode->clock > 135000 && tc->dual_link == 0) || + (mode->clock > 270000 && tc->dual_link == 1)) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + +static struct drm_encoder * +tc_connector_best_encoder(struct drm_connector *connector) +{ + struct tc_data *tc = connector_to_tc(connector); + + return tc->bridge.encoder; +} + +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { + .get_modes = tc_connector_get_modes, + .mode_valid = tc_connector_mode_valid, + .best_encoder = tc_connector_best_encoder, +}; + +static const struct drm_connector_funcs tc_connector_funcs = { + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = drm_connector_cleanup, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc) +{ + u32 num_lanes; + u8 dual_link, data_format; + + of_property_read_u8(np, "tc,dual-link", &dual_link); + of_property_read_u8(np, "tc,data-format", &data_format); + of_property_read_u32(np, "tc,dsi-lanes", &num_lanes); + + if (num_lanes < 1 || num_lanes > 4) + return -EINVAL; + + tc->num_dsi_lanes = num_lanes; + tc->dual_link = dual_link; + tc->data_format = data_format; + + tc->host_node = of_graph_get_remote_node(np, 0, 0); + if (!tc->host_node) + return -ENODEV; + + of_node_put(tc->host_node); + + return 0; +} + +int tc358775_attach_dsi(struct tc_data *tc) +{ + struct device *dev = &tc->i2c->dev; + struct mipi_dsi_host *host; + struct mipi_dsi_device *dsi; + int ret = 0; + const struct mipi_dsi_device_info info = { .type = "tc358775", + .channel = 0, + .node = NULL, + }; + + host = of_find_mipi_dsi_host_by_node(tc->host_node); + if (!host) { + dev_err(dev, "failed to find dsi host\n"); + return -EPROBE_DEFER; + } + + dsi = mipi_dsi_device_register_full(host, &info); + if (IS_ERR(dsi)) { + dev_err(dev, "failed to create dsi device\n"); + ret = PTR_ERR(dsi); + goto err_dsi_device; + } + + tc->dsi = dsi; + + dsi->lanes = tc->num_dsi_lanes; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = MIPI_DSI_MODE_VIDEO; + + ret = mipi_dsi_attach(dsi); + if (ret < 0) { + dev_err(dev, "failed to attach dsi to host\n"); + goto err_dsi_attach; + } + + return 0; + +err_dsi_attach: + mipi_dsi_device_unregister(dsi); +err_dsi_device: + return ret; +} + +static int tc_bridge_attach(struct drm_bridge *bridge) +{ + struct tc_data *tc = bridge_to_tc(bridge); + struct drm_device *drm = bridge->dev; + int ret; + + /* Create LVDS connector */ + drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); + ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, + DRM_MODE_CONNECTOR_LVDS); + if (ret) + return ret; + + if (tc->panel) + drm_panel_attach(tc->panel, &tc->connector); + + drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); + + ret = tc358775_attach_dsi(tc); + + return 0; +} + +static const struct drm_bridge_funcs tc_bridge_funcs = { + .attach = tc_bridge_attach, + .pre_enable = tc_bridge_pre_enable, + .enable = tc_bridge_enable, + .disable = tc_bridge_disable, + .post_disable = tc_bridge_post_disable, +}; + +static const struct regmap_config tc_regmap_config = { + .name = "tc358775", + .reg_bits = 16, + .val_bits = 32, + .reg_stride = 4, + .max_register = 0x05A8, + .cache_type = REGCACHE_RBTREE, + .reg_format_endian = REGMAP_ENDIAN_BIG, + .val_format_endian = REGMAP_ENDIAN_LITTLE, +}; + +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + struct tc_data *tc; + int ret; + unsigned int i; + + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); + if (!tc) + return -ENOMEM; + + tc->dev = dev; + tc->i2c = client; + tc->status = connector_status_connected; + + /* port@1 is the output port */ + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL); + if (ret && ret != -ENODEV) + return ret; + + ret = tc358775_parse_dt(dev->of_node, tc); + if (ret) + return ret; + + for (i = 0; i < ARRAY_SIZE(tc->supplies); i++) + tc->supplies[i].supply = regulator_names[i]; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies), + tc->supplies); + if (ret < 0) + dev_err(dev, "failed to init regulator, ret=%d\n", ret); + + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH); + if (IS_ERR(tc->stby_gpio)) { + ret = PTR_ERR(tc->stby_gpio); + dev_err(dev, "cannot get stby-gpio %d\n", ret); + return ret; + } + + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(tc->reset_gpio)) { + ret = PTR_ERR(tc->reset_gpio); + dev_err(dev, "cannot get reset-gpios %d\n", ret); + return ret; + } + + tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); + if (IS_ERR(tc->regmap)) { + ret = PTR_ERR(tc->regmap); + dev_err(dev, "Failed to initialize regmap: %d\n", ret); + return ret; + } + + tc->bridge.funcs = &tc_bridge_funcs; + tc->bridge.of_node = dev->of_node; + drm_bridge_add(&tc->bridge); + + i2c_set_clientdata(client, tc); + + return 0; +} + +static int tc_remove(struct i2c_client *client) +{ + struct tc_data *tc = i2c_get_clientdata(client); + + drm_bridge_remove(&tc->bridge); + + return 0; +} + +static const struct i2c_device_id tc358775_i2c_ids[] = { + { "tc358775", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids); + +static const struct of_device_id tc358775_of_ids[] = { + { .compatible = "toshiba,tc358775", }, + { } +}; +MODULE_DEVICE_TABLE(of, tc358775_of_ids); + +static struct i2c_driver tc358775_driver = { + .driver = { + .name = "tc358775", + .of_match_table = tc358775_of_ids, + }, + .id_table = tc358775_i2c_ids, + .probe = tc_probe, + .remove = tc_remove, +}; +module_i2c_driver(tc358775_driver); + +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>"); +MODULE_DESCRIPTION("tc358775 LVDS encoder driver"); +MODULE_LICENSE("GPL v2");
dsi2lvds tc358775 bridge driver added Tested in apq8016, ifc6309 board and panel auo,b101xtn01 Signed-off-by: Vinay Simha BN <simhavcs@gmail.com> --- .../bindings/display/bridge/toshiba,tc358775.txt | 106 ++++ drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/tc358775.c | 687 +++++++++++++++++++++ 4 files changed, 804 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt create mode 100644 drivers/gpu/drm/bridge/tc358775.c -- 2.7.4 _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel