new file mode 100644
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2019 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/net/ti,dp83869.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI DP83869 ethernet PHY
+
+allOf:
+ - $ref: "ethernet-controller.yaml#"
+
+maintainers:
+ - Dan Murphy <dmurphy@ti.com>
+
+description: |
+ The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver
+ with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and
+ 1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and
+ 100BASE-FX Fiber protocols.
+ This device interfaces to the MAC layer through Reduced GMII (RGMII) and
+ SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode,
+ the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX
+ conversions. The DP83869HM can also support Bridge Conversion from RGMII to
+ SGMII and SGMII to RGMII.
+
+ Specifications about the charger can be found at:
+ http://www.ti.com/lit/ds/symlink/dp83869hm.pdf
+
+properties:
+ reg:
+ maxItems: 1
+
+ ti,min-output-impedance:
+ type: boolean
+ description: |
+ MAC Interface Impedance control to set the programmable output impedance
+ to a minimum value (35 ohms).
+
+ ti,max-output-impedance:
+ type: boolean
+ description: |
+ MAC Interface Impedance control to set the programmable output impedance
+ to a maximum value (70 ohms).
+
+ tx-fifo-depth:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+ rx-fifo-depth:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+ ti,clk-output-sel:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values.
+
+ ti,op-mode:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Operational mode for the PHY. If this is not set then the operational
+ mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values
+
+required:
+ - reg
+
+examples:
+ - |
+ #include <dt-bindings/net/ti-dp83869.h>
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+ ti,max-output-impedance = "true";
+ ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>;
+ };
+ };
new file mode 100644
@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Device Tree constants for the Texas Instruments DP83869 PHY
+ *
+ * Author: Dan Murphy <dmurphy@ti.com>
+ *
+ * Copyright: (C) 2019 Texas Instruments, Inc.
+ */
+
+#ifndef _DT_BINDINGS_TI_DP83869_H
+#define _DT_BINDINGS_TI_DP83869_H
+
+/* PHY CTRL bits */
+#define DP83869_PHYCR_FIFO_DEPTH_3_B_NIB 0x00
+#define DP83869_PHYCR_FIFO_DEPTH_4_B_NIB 0x01
+#define DP83869_PHYCR_FIFO_DEPTH_6_B_NIB 0x02
+#define DP83869_PHYCR_FIFO_DEPTH_8_B_NIB 0x03
+
+/* IO_MUX_CFG - Clock output selection */
+#define DP83869_CLK_O_SEL_CHN_A_RCLK 0x0
+#define DP83869_CLK_O_SEL_CHN_B_RCLK 0x1
+#define DP83869_CLK_O_SEL_CHN_C_RCLK 0x2
+#define DP83869_CLK_O_SEL_CHN_D_RCLK 0x3
+#define DP83869_CLK_O_SEL_CHN_A_RCLK_DIV5 0x4
+#define DP83869_CLK_O_SEL_CHN_B_RCLK_DIV5 0x5
+#define DP83869_CLK_O_SEL_CHN_C_RCLK_DIV5 0x6
+#define DP83869_CLK_O_SEL_CHN_D_RCLK_DIV5 0x7
+#define DP83869_CLK_O_SEL_CHN_A_TCLK 0x8
+#define DP83869_CLK_O_SEL_CHN_B_TCLK 0x9
+#define DP83869_CLK_O_SEL_CHN_C_TCLK 0xa
+#define DP83869_CLK_O_SEL_CHN_D_TCLK 0xb
+#define DP83869_CLK_O_SEL_REF_CLK 0xc
+
+#define DP83869_RGMII_COPPER_ETHERNET 0x00
+#define DP83869_RGMII_1000_BASE 0x01
+#define DP83869_RGMII_100_BASE 0x02
+#define DP83869_RGMII_SGMII_BRIDGE 0x03
+#define DP83869_1000M_MEDIA_CONVERT 0x04
+#define DP83869_100M_MEDIA_CONVERT 0x05
+#define DP83869_SGMII_COPPER_ETHERNET 0x06
+
+#endif
+
Add dt bindings for the TI dp83869 Gigabit ethernet phy device. Signed-off-by: Dan Murphy <dmurphy@ti.com> CC: Rob Herring <robh+dt@kernel.org> --- v3 - Moved dt-bindings header file from patch 2/2 to here .../devicetree/bindings/net/ti,dp83869.yaml | 84 +++++++++++++++++++ include/dt-bindings/net/ti-dp83869.h | 43 ++++++++++ 2 files changed, 127 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/ti,dp83869.yaml create mode 100644 include/dt-bindings/net/ti-dp83869.h -- 2.22.0.214.g8dca754b1e