@@ -62,12 +62,12 @@ Example:
cpu@0 {
device_type = "cpu";
reg = <0>;
- status = "ok";
+ status = "okay";
};
cpu@1 {
device_type = "cpu";
reg = <1>;
- status = "ok";
+ status = "okay";
};
};
@@ -42,7 +42,7 @@ SoC specific:
Board specific:
&dsi {
- status = "ok";
+ status = "okay";
ports {
/* 1 for output port */
@@ -183,7 +183,7 @@ OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI Connector
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -197,7 +197,7 @@ OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI Connector
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
pinctrl-names = "default";
@@ -55,7 +55,7 @@ Example:
menetclk: menetclk {
compatible = "apm,xgene-device-clock";
clock-output-names = "menetclk";
- status = "ok";
+ status = "okay";
};
menet: ethernet@17020000 {
@@ -87,5 +87,5 @@ Example:
&menet {
tx-delay = <4>;
rx-delay = <2>;
- status = "ok";
+ status = "okay";
};
@@ -148,7 +148,7 @@ arch/arm/boot/dts/ls1021a-tsn.dts:
/* Ethernet master port of the LS1021 */
&enet2 {
phy-connection-type = "rgmii";
- status = "ok";
+ status = "okay";
fixed-link {
speed = <1000>;
full-duplex;
@@ -183,14 +183,14 @@
};
&mcbsp1 {
- status = "ok";
+ status = "okay";
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp1_pins>;
};
&mcbsp2 {
- status = "ok";
+ status = "okay";
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp2_pins>;
@@ -190,7 +190,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -1040,7 +1040,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_pins>;
@@ -136,7 +136,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_pinctrl_default>;
@@ -941,7 +941,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_pins>;
@@ -526,13 +526,13 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdda_video-supply = <&ldoln_reg>;
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&ldo4_reg>;
port {
@@ -543,7 +543,7 @@
};
&pcie1_rc {
- status = "ok";
+ status = "okay";
gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
};
@@ -120,7 +120,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdda_video-supply = <&ldoln_reg>;
@@ -148,7 +148,7 @@
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&ldo4_reg>;
pinctrl-names = "default";
@@ -57,7 +57,7 @@
};
usb@58000 {
- status = "ok";
+ status = "okay";
};
ethernet@70000 {
@@ -192,7 +192,7 @@
};
&sdio {
- status = "ok";
+ status = "okay";
};
&uart0 {
@@ -204,7 +204,7 @@
&sdio {
bus-width = <4>;
no-1-8-v;
- status = "ok";
+ status = "okay";
};
&srab {
@@ -415,7 +415,7 @@
&aemif {
pinctrl-names = "default";
pinctrl-0 = <&nand_pins>;
- status = "ok";
+ status = "okay";
cs3 {
#address-cells = <2>;
#size-cells = <1>;
@@ -408,7 +408,7 @@
clocks = <&gate_clk 3>;
clock-names = "sata";
#phy-cells = <0>;
- status = "ok";
+ status = "okay";
};
audio0: audio-controller@b0000 {
@@ -531,7 +531,7 @@
};
&dcan1 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default", "sleep", "active";
pinctrl-0 = <&dcan1_pins_sleep>;
pinctrl-1 = <&dcan1_pins_sleep>;
@@ -443,7 +443,7 @@
};
&dcan1 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default", "sleep", "active";
pinctrl-0 = <&dcan1_pins_sleep>;
pinctrl-1 = <&dcan1_pins_sleep>;
@@ -512,11 +512,11 @@
};
&dss {
- status = "ok";
+ status = "okay";
};
&hdmi {
- status = "ok";
+ status = "okay";
port {
hdmi_out: endpoint {
@@ -24,12 +24,12 @@
soc {
adc@40002000 {
- status = "ok";
+ status = "okay";
};
i2c@4000a000 {
energymicro,location = <3>;
- status = "ok";
+ status = "okay";
temp@48 {
compatible = "st,stds75";
@@ -46,7 +46,7 @@
spi0: spi@4000c000 { /* USART0 */
cs-gpios = <&gpio 68 1>; // E4
energymicro,location = <1>;
- status = "ok";
+ status = "okay";
microsd@0 {
compatible = "mmc-spi-slot";
@@ -60,7 +60,7 @@
spi1: spi@4000c400 { /* USART1 */
cs-gpios = <&gpio 51 1>; // D3
energymicro,location = <1>;
- status = "ok";
+ status = "okay";
ks8851@0 {
compatible = "ks8851";
@@ -73,7 +73,7 @@
uart4: uart@4000e400 { /* UART1 */
energymicro,location = <2>;
- status = "ok";
+ status = "okay";
};
boardfpga: boardfpga@80000000 {
@@ -82,7 +82,7 @@
irq-gpios = <&gpio 64 1>;
interrupt-controller;
#interrupt-cells = <1>;
- status = "ok";
+ status = "okay";
};
};
};
@@ -44,7 +44,7 @@
interrupt-controller;
#interrupt-cells = <1>;
clocks = <&cmu clk_HFPERCLKGPIO>;
- status = "ok";
+ status = "okay";
};
i2c0: i2c@4000a000 {
@@ -24,42 +24,42 @@
amba {
dual_timer0: dual_timer@800000 {
- status = "ok";
+ status = "okay";
};
uart0: uart@b00000 { /* console */
pinctrl-names = "default", "idle";
pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
pinctrl-1 = <&uart0_pmx_idle &uart0_cfg_idle>;
- status = "ok";
+ status = "okay";
};
uart1: uart@b01000 { /* modem */
pinctrl-names = "default", "idle";
pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
pinctrl-1 = <&uart1_pmx_idle &uart1_cfg_idle>;
- status = "ok";
+ status = "okay";
};
uart2: uart@b02000 { /* audience */
pinctrl-names = "default", "idle";
pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
pinctrl-1 = <&uart2_pmx_idle &uart2_cfg_idle>;
- status = "ok";
+ status = "okay";
};
uart3: uart@b03000 {
pinctrl-names = "default", "idle";
pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
pinctrl-1 = <&uart3_pmx_idle &uart3_cfg_idle>;
- status = "ok";
+ status = "okay";
};
uart4: uart@b04000 {
pinctrl-names = "default", "idle";
pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
pinctrl-1 = <&uart4_pmx_idle &uart4_cfg_func>;
- status = "ok";
+ status = "okay";
};
pmx0: pinmux@803000 {
@@ -23,7 +23,7 @@
soc {
uart0: uart@4007000 {
- status = "ok";
+ status = "okay";
};
};
};
@@ -159,7 +159,7 @@
};
&mdio {
- status = "ok";
+ status = "okay";
ethphy0: ethernet-phy@0 {
compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
reg = <0>;
@@ -183,7 +183,7 @@
};
&mdio {
- status = "ok";
+ status = "okay";
ethphy0: ethernet-phy@0 {
compatible = "marvell,88E1111", "ethernet-phy-ieee802.3-c22";
reg = <0>;
@@ -132,7 +132,7 @@
};
&mdio {
- status = "ok";
+ status = "okay";
ethphy0: ethernet-phy@0 {
compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
reg = <0>;
@@ -34,7 +34,7 @@
};
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
};
gpio-leds {
@@ -34,7 +34,7 @@
};
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
spi@10600 {
@@ -66,7 +66,7 @@
};
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
sata@80000 {
@@ -38,7 +38,7 @@
};
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
sata@80000 {
@@ -72,7 +72,7 @@
};
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
};
@@ -112,7 +112,7 @@
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
sata@80000 {
@@ -45,7 +45,7 @@
};
serial@12000 {
- status = "ok";
+ status = "okay";
};
sata@80000 {
@@ -369,7 +369,7 @@
clocks = <&gate_clk 14>;
clock-names = "sata";
#phy-cells = <0>;
- status = "ok";
+ status = "okay";
};
sata_phy1: sata-phy@84000 {
@@ -378,7 +378,7 @@
clocks = <&gate_clk 15>;
clock-names = "sata";
#phy-cells = <0>;
- status = "ok";
+ status = "okay";
};
audio0: audio-controller@a0000 {
@@ -77,7 +77,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdds_dsi-supply = <&vpll2>;
vdda_video-supply = <&video_reg>;
pinctrl-names = "default";
@@ -106,7 +106,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdds_dsi-supply = <&vpll2>;
vdda_video-supply = <&video_reg>;
pinctrl-names = "default";
@@ -389,7 +389,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <
@@ -406,7 +406,7 @@
};
&venc {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
@@ -353,7 +353,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -367,7 +367,7 @@
};
&venc {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
@@ -380,7 +380,7 @@
};
&gpmc {
- status = "ok";
+ status = "okay";
ranges = <0 0 0x30000000 0x1000000>; /* CS0 space, 16MB */
/* Chip select 0 */
@@ -147,7 +147,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <
@@ -49,7 +49,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <
@@ -87,7 +87,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <
@@ -246,7 +246,7 @@
};
&venc {
- status = "ok";
+ status = "okay";
port {
venc_out: endpoint {
@@ -257,7 +257,7 @@
};
&mcbsp2 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcbsp2_pins>;
@@ -337,7 +337,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -361,7 +361,7 @@
};
&venc {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
@@ -820,27 +820,27 @@
};
&mcbsp1 { /* FM Transceiver PCM */
- status = "ok";
+ status = "okay";
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp1_pins>;
};
&mcbsp2 { /* TPS65950 I2S */
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcbsp2_pins>;
};
&mcbsp3 { /* Bluetooth PCM */
- status = "ok";
+ status = "okay";
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp3_pins>;
};
&mcbsp4 { /* GSM voice PCM */
- status = "ok";
+ status = "okay";
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp4_pins>;
@@ -100,7 +100,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -245,7 +245,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
port {
dpi_out: endpoint {
@@ -1047,7 +1047,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_sdi_pins>;
@@ -1070,7 +1070,7 @@
};
&venc {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
@@ -1083,7 +1083,7 @@
};
&mcbsp2 {
- status = "ok";
+ status = "okay";
};
&ssi_port1 {
@@ -205,13 +205,13 @@
};
&dss {
- status = "ok";
+ status = "okay";
vdda_video-supply = <&vdac>;
};
&dsi {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dsi_pins>;
@@ -48,7 +48,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -76,7 +76,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -75,7 +75,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -670,7 +670,7 @@
};
&venc {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
@@ -686,7 +686,7 @@
pinctrl-names = "default";
pinctrl-0 = < &dss_dpi_pins >;
- status = "ok";
+ status = "okay";
vdds_dsi-supply = <&vpll2>;
port {
@@ -46,7 +46,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
port {
dpi_out: endpoint {
remote-endpoint = <&lcd_in>;
@@ -64,7 +64,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -134,7 +134,7 @@
};
&ssi {
- status = "ok";
+ status = "okay";
clocks = <&ssi_ssr_fck>,
<&ssi_sst_fck>,
@@ -181,7 +181,7 @@
};
&ssi {
- status = "ok";
+ status = "okay";
clocks = <&ssi_ssr_fck>,
<&ssi_sst_fck>,
@@ -171,11 +171,11 @@
};
&dss {
- status = "ok";
+ status = "okay";
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
pinctrl-names = "default";
@@ -546,7 +546,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
port {
dpi_out: endpoint {
@@ -557,12 +557,12 @@
};
&dsi2 {
- status = "ok";
+ status = "okay";
vdd-supply = <&vcxio>;
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
port {
@@ -648,11 +648,11 @@
};
&dss {
- status = "ok";
+ status = "okay";
};
&dsi1 {
- status = "ok";
+ status = "okay";
vdd-supply = <&vcxio>;
port {
@@ -677,7 +677,7 @@
};
&dsi2 {
- status = "ok";
+ status = "okay";
vdd-supply = <&vcxio>;
port {
@@ -702,7 +702,7 @@
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&vdac>;
port {
@@ -743,11 +743,11 @@
};
&dss {
- status = "ok";
+ status = "okay";
};
&hdmi {
- status = "ok";
+ status = "okay";
/* vdda-supply populated in board specific dts file */
@@ -653,7 +653,7 @@
};
&dss {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
@@ -677,12 +677,12 @@
};
&dsi2 {
- status = "ok";
+ status = "okay";
vdd-supply = <&ldo4_reg>;
};
&hdmi {
- status = "ok";
+ status = "okay";
vdda-supply = <&ldo4_reg>;
pinctrl-names = "default";
@@ -461,11 +461,11 @@
};
gsbi@19800000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
i2c@19880000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
@@ -497,17 +497,17 @@
};
gsbi@19c00000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@19c40000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dragon_gsbi12_serial_pins>;
};
i2c@19c80000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
@@ -571,7 +571,7 @@
external-bus@1a100000 {
/* The EBI2 will instantiate first, then populate its children */
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dragon_ebi2_pins>;
@@ -302,11 +302,11 @@
};
gsbi@16500000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16540000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gsbi6_uart_4pins>;
@@ -314,10 +314,10 @@
};
gsbi@16600000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16640000 {
- status = "ok";
+ status = "okay";
};
};
@@ -141,10 +141,10 @@
};
gsbi@16600000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16640000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gsbi7_uart_2pins>;
};
@@ -152,7 +152,7 @@
/* OTG */
usb@12500000 {
- status = "ok";
+ status = "okay";
dr_mode = "otg";
ulpi {
phy {
@@ -209,7 +209,7 @@
};
pci@1b500000 {
- status = "ok";
+ status = "okay";
vdda-supply = <&pm8921_s3>;
vdda_phy-supply = <&pm8921_lvs6>;
vdda_refclk-supply = <&v3p3_fixed>;
@@ -215,21 +215,21 @@
};
gsbi@16500000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_UART_W_FC>;
serial@16540000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gsbi6_uart_4pins>;
};
};
gsbi@16600000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16640000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gsbi7_uart_2pins>;
};
@@ -279,7 +279,7 @@
};
pci@1b500000 {
- status = "ok";
+ status = "okay";
vdda-supply = <&pm8921_s3>;
vdda_phy-supply = <&pm8921_lvs6>;
vdda_refclk-supply = <&ext_3p3v>;
@@ -362,11 +362,11 @@
};
gsbi@1a200000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@1a240000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gsbi5_uart_pin_a>;
@@ -19,13 +19,13 @@
soc {
serial@f991e000 {
- status = "ok";
+ status = "okay";
};
sdhci@f9824900 {
bus-width = <8>;
non-removable;
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
@@ -39,14 +39,14 @@
pinctrl-names = "default";
pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
bus-width = <4>;
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
};
usb@f9a55000 {
- status = "ok";
+ status = "okay";
phys = <&usb_hs2_phy>;
phy-select = <&tcsr 0xb000 1>;
extcon = <&smbb>, <&usb_id>;
@@ -56,7 +56,7 @@
adp-disable;
ulpi {
phy@b {
- status = "ok";
+ status = "okay";
v3p3-supply = <&pm8941_l24>;
v1p8-supply = <&pm8941_l6>;
extcon = <&smbb>;
@@ -30,7 +30,7 @@
soc {
rng@22000 {
- status = "ok";
+ status = "okay";
};
pinctrl@1000000 {
@@ -66,13 +66,13 @@
};
blsp_dma: dma@7884000 {
- status = "ok";
+ status = "okay";
};
spi@78b5000 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
cs-gpios = <&tlmm 54 0>;
mx25l25635e@0 {
@@ -87,27 +87,27 @@
serial@78af000 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
cryptobam: dma@8e04000 {
- status = "ok";
+ status = "okay";
};
crypto@8e3a000 {
- status = "ok";
+ status = "okay";
};
watchdog@b017000 {
- status = "ok";
+ status = "okay";
};
wifi@a000000 {
- status = "ok";
+ status = "okay";
};
wifi@a800000 {
- status = "ok";
+ status = "okay";
};
};
};
@@ -9,11 +9,11 @@
soc {
dma@7984000 {
- status = "ok";
+ status = "okay";
};
qpic-nand@79b0000 {
- status = "ok";
+ status = "okay";
};
};
};
@@ -70,23 +70,23 @@
serial@78af000 {
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
serial@78b0000 {
pinctrl-0 = <&serial_1_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
dma@7884000 {
- status = "ok";
+ status = "okay";
};
spi@78b5000 { /* BLSP1 QUP1 */
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
cs-gpios = <&tlmm 12 0>;
m25p80@0 {
@@ -99,7 +99,7 @@
};
pci@40000000 {
- status = "ok";
+ status = "okay";
perst-gpio = <&tlmm 38 0x1>;
};
@@ -9,12 +9,12 @@
soc {
pci@40000000 {
- status = "ok";
+ status = "okay";
perst-gpio = <&tlmm 38 0x1>;
};
spi@78b6000 {
- status = "ok";
+ status = "okay";
};
pinctrl@1000000 {
@@ -43,13 +43,13 @@
serial@78b0000 {
pinctrl-0 = <&serial_1_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
spi@78b5000 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
cs-gpios = <&tlmm 12 0>;
m25p80@0 {
@@ -19,7 +19,7 @@
serial@78b0000 {
pinctrl-0 = <&serial_1_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
};
};
@@ -49,27 +49,27 @@
serial@78af000 {
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
dma@7884000 {
- status = "ok";
+ status = "okay";
};
i2c@78b7000 { /* BLSP1 QUP2 */
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
dma@7984000 {
- status = "ok";
+ status = "okay";
};
qpic-nand@79b0000 {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
- status = "ok";
+ status = "okay";
};
};
};
@@ -24,7 +24,7 @@
gsbi@16300000 {
i2c@16380000 {
- status = "ok";
+ status = "okay";
clock-frequency = <200000>;
pinctrl-0 = <&i2c4_pins>;
pinctrl-names = "default";
@@ -16,19 +16,19 @@
soc {
gsbi@16300000 {
qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
+ status = "okay";
serial@16340000 {
- status = "ok";
+ status = "okay";
};
};
gsbi5: gsbi@1a200000 {
qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
+ status = "okay";
spi4: spi@1a280000 {
- status = "ok";
+ status = "okay";
spi-max-frequency = <50000000>;
pinctrl-0 = <&spi_pins>;
@@ -57,12 +57,12 @@
};
sata-phy@1b400000 {
- status = "ok";
+ status = "okay";
};
sata@29000000 {
ports-implemented = <0x1>;
- status = "ok";
+ status = "okay";
};
gpio_keys {
@@ -125,12 +125,12 @@
};
&gsbi3 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_SPI>;
};
&gsbi3_spi {
- status = "ok";
+ status = "okay";
pinctrl-0 = <&gsbi3_pins>;
pinctrl-names = "default";
assigned-clocks = <&gcc GSBI3_QUP_CLK>;
@@ -138,34 +138,34 @@
};
&gsbi4 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_UART_W_FC>;
};
&gsbi4_serial {
- status = "ok";
+ status = "okay";
pinctrl-0 = <&gsbi4_pins>;
pinctrl-names = "default";
};
&gsbi5 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
};
&gsbi5_i2c {
- status = "ok";
+ status = "okay";
clock-frequency = <200000>;
pinctrl-0 = <&gsbi5_i2c_pins>;
pinctrl-names = "default";
};
&gsbi5_serial {
- status = "ok";
+ status = "okay";
pinctrl-0 = <&gsbi5_uart_pins>;
pinctrl-names = "default";
};
&sdcc1 {
- status = "ok";
+ status = "okay";
};
@@ -17,10 +17,10 @@
soc {
gsbi@19c00000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@19c40000 {
- status = "ok";
+ status = "okay";
};
};
@@ -17,10 +17,10 @@
soc {
gsbi@16400000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16440000 {
- status = "ok";
+ status = "okay";
};
};
@@ -273,12 +273,12 @@
};
gsbi@16000000 {
- status = "ok";
+ status = "okay";
qcom,mode = <GSBI_PROT_SPI>;
pinctrl-names = "default";
pinctrl-0 = <&spi1_default>;
spi@16080000 {
- status = "ok";
+ status = "okay";
eth@0 {
compatible = "micrel,ks8851";
reg = <0>;
@@ -254,7 +254,7 @@
&soc {
serial@f991e000 {
- status = "ok";
+ status = "okay";
};
pinctrl@fd510000 {
@@ -296,7 +296,7 @@
};
sdhci@f9824900 {
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
@@ -309,7 +309,7 @@
};
sdhci@f98a4900 {
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
@@ -321,7 +321,7 @@
};
usb@f9a55000 {
- status = "ok";
+ status = "okay";
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
@@ -334,7 +334,7 @@
ulpi {
phy@a {
- status = "ok";
+ status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
@@ -238,7 +238,7 @@
&soc {
serial@f991d000 {
- status = "ok";
+ status = "okay";
};
pinctrl@fd510000 {
@@ -358,7 +358,7 @@
};
sdhci@f9824900 {
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
@@ -371,7 +371,7 @@
};
sdhci@f98a4900 {
- status = "ok";
+ status = "okay";
max-frequency = <100000000>;
bus-width = <4>;
@@ -419,7 +419,7 @@
};
i2c@f9967000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c11_pins>;
clock-frequency = <355000>;
@@ -427,7 +427,7 @@
led-controller@38 {
compatible = "ti,lm3630a";
- status = "ok";
+ status = "okay";
reg = <0x38>;
#address-cells = <1>;
@@ -443,7 +443,7 @@
};
i2c@f9968000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c12_pins>;
clock-frequency = <100000>;
@@ -480,7 +480,7 @@
};
i2c@f9923000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <100000>;
@@ -498,7 +498,7 @@
};
i2c@f9924000 {
- status = "ok";
+ status = "okay";
clock-frequency = <355000>;
qcom,src-freq = <50000000>;
@@ -533,7 +533,7 @@
};
i2c@f9925000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <100000>;
@@ -551,7 +551,7 @@
};
usb@f9a55000 {
- status = "ok";
+ status = "okay";
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
@@ -565,7 +565,7 @@
ulpi {
phy@a {
- status = "ok";
+ status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
@@ -576,14 +576,14 @@
};
mdss@fd900000 {
- status = "ok";
+ status = "okay";
mdp@fd900000 {
- status = "ok";
+ status = "okay";
};
dsi@fd922800 {
- status = "ok";
+ status = "okay";
vdda-supply = <&pm8941_l2>;
vdd-supply = <&pm8941_lvs3>;
@@ -617,7 +617,7 @@
};
dsi-phy@fd922a00 {
- status = "ok";
+ status = "okay";
vddio-supply = <&pm8941_l12>;
};
@@ -18,7 +18,7 @@
&soc {
serial@f991e000 {
- status = "ok";
+ status = "okay";
};
};
@@ -261,7 +261,7 @@
&soc {
sdhci@f9824900 {
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
@@ -274,7 +274,7 @@
};
sdhci@f98a4900 {
- status = "ok";
+ status = "okay";
bus-width = <4>;
@@ -288,7 +288,7 @@
};
serial@f991e000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart2_pin_a>;
@@ -366,7 +366,7 @@
};
usb@f9a55000 {
- status = "ok";
+ status = "okay";
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
@@ -379,7 +379,7 @@
ulpi {
phy@a {
- status = "ok";
+ status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
@@ -415,7 +415,7 @@
};
coincell@2800 {
- status = "ok";
+ status = "okay";
qcom,rset-ohms = <2100>;
qcom,vset-millivolts = <3000>;
};
@@ -423,7 +423,7 @@
pm8941@1 {
wled@d800 {
- status = "ok";
+ status = "okay";
qcom,cs-out;
qcom,current-limit = <20>;
@@ -279,7 +279,7 @@
&soc {
sdhci@f9824900 {
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
@@ -292,7 +292,7 @@
};
sdhci@f9864900 {
- status = "ok";
+ status = "okay";
max-frequency = <100000000>;
non-removable;
@@ -316,7 +316,7 @@
};
sdhci@f98a4900 {
- status = "ok";
+ status = "okay";
bus-width = <4>;
@@ -330,14 +330,14 @@
};
serial@f991e000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart2_pin_a>;
};
usb@f9a55000 {
- status = "ok";
+ status = "okay";
phys = <&usb_hs1_phy>;
phy-select = <&tcsr 0xb000 0>;
@@ -350,7 +350,7 @@
ulpi {
phy@a {
- status = "ok";
+ status = "okay";
v1p8-supply = <&pm8941_l6>;
v3p3-supply = <&pm8941_l24>;
@@ -482,7 +482,7 @@
};
i2c@f9964000 {
- status = "ok";
+ status = "okay";
clock-frequency = <355000>;
qcom,src-freq = <50000000>;
@@ -522,7 +522,7 @@
};
i2c@f9967000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c11_pins>;
clock-frequency = <355000>;
@@ -635,7 +635,7 @@
};
coincell@2800 {
- status = "ok";
+ status = "okay";
qcom,rset-ohms = <2100>;
qcom,vset-millivolts = <3000>;
};
@@ -261,7 +261,7 @@
&soc {
sdhci@f9824900 {
- status = "ok";
+ status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
@@ -274,7 +274,7 @@
};
sdhci@f98a4900 {
- status = "ok";
+ status = "okay";
bus-width = <4>;
@@ -288,14 +288,14 @@
};
serial@f991e000 {
- status = "ok";
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&blsp1_uart2_pin_a>;
};
i2c@f9924000 {
- status = "ok";
+ status = "okay";
clock-frequency = <355000>;
qcom,src-freq = <50000000>;
@@ -439,7 +439,7 @@
};
coincell@2800 {
- status = "ok";
+ status = "okay";
qcom,rset-ohms = <2100>;
qcom,vset-millivolts = <3000>;
};
@@ -447,7 +447,7 @@
pm8941@1 {
wled@d800 {
- status = "ok";
+ status = "okay";
qcom,cs-out;
qcom,current-limit = <20>;
@@ -247,7 +247,7 @@
pinctrl-0 = <&rgmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&gpu {
@@ -61,7 +61,7 @@
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&i2c0 {
@@ -191,7 +191,7 @@
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&gpu {
@@ -108,7 +108,7 @@
snps,reset-gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_LOW>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&hdmi {
@@ -149,7 +149,7 @@
pinctrl-0 = <&rgmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&hdmi {
@@ -106,7 +106,7 @@
pinctrl-0 = <&rgmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&hdmi {
@@ -156,7 +156,7 @@
};
&gmac {
- status = "ok";
+ status = "okay";
};
&hdmi {
@@ -126,7 +126,7 @@
snps,reset-delays-us = <0 10000 1000000>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&gpu {
@@ -25,7 +25,7 @@
};
&ccp0 {
- status = "ok";
+ status = "okay";
amd,zlib-support = <1>;
};
@@ -33,39 +33,39 @@
* NOTE: In Rev.B, gpio0 is reserved.
*/
&gpio1 {
- status = "ok";
+ status = "okay";
};
&gpio2 {
- status = "ok";
+ status = "okay";
};
&gpio3 {
- status = "ok";
+ status = "okay";
};
&gpio4 {
- status = "ok";
+ status = "okay";
};
&i2c0 {
- status = "ok";
+ status = "okay";
};
&i2c1 {
- status = "ok";
+ status = "okay";
};
&pcie0 {
- status = "ok";
+ status = "okay";
};
&spi0 {
- status = "ok";
+ status = "okay";
};
&spi1 {
- status = "ok";
+ status = "okay";
sdcard0: sdcard@0 {
compatible = "mmc-spi-slot";
reg = <0>;
@@ -80,7 +80,7 @@
};
&ipmi_kcs {
- status = "ok";
+ status = "okay";
};
&smb0 {
@@ -25,7 +25,7 @@
};
&ccp0 {
- status = "ok";
+ status = "okay";
amd,zlib-support = <1>;
};
@@ -33,43 +33,43 @@
* NOTE: In Rev.B, gpio0 is reserved.
*/
&gpio1 {
- status = "ok";
+ status = "okay";
};
&gpio2 {
- status = "ok";
+ status = "okay";
};
&gpio3 {
- status = "ok";
+ status = "okay";
};
&gpio4 {
- status = "ok";
+ status = "okay";
};
&i2c0 {
- status = "ok";
+ status = "okay";
};
&i2c1 {
- status = "ok";
+ status = "okay";
};
&pcie0 {
- status = "ok";
+ status = "okay";
};
&sata1 {
- status = "ok";
+ status = "okay";
};
&spi0 {
- status = "ok";
+ status = "okay";
};
&spi1 {
- status = "ok";
+ status = "okay";
sdcard0: sdcard@0 {
compatible = "mmc-spi-slot";
reg = <0>;
@@ -84,7 +84,7 @@
};
&ipmi_kcs {
- status = "ok";
+ status = "okay";
};
&smb0 {
@@ -19,31 +19,31 @@
};
&ccp0 {
- status = "ok";
+ status = "okay";
};
&gpio0 {
- status = "ok";
+ status = "okay";
};
&gpio1 {
- status = "ok";
+ status = "okay";
};
&i2c0 {
- status = "ok";
+ status = "okay";
};
&pcie0 {
- status = "ok";
+ status = "okay";
};
&spi0 {
- status = "ok";
+ status = "okay";
};
&spi1 {
- status = "ok";
+ status = "okay";
sdcard0: sdcard@0 {
compatible = "mmc-spi-slot";
reg = <0>;
@@ -25,7 +25,7 @@
};
&ccp0 {
- status = "ok";
+ status = "okay";
amd,zlib-support = <1>;
};
@@ -33,39 +33,39 @@
* NOTE: In Rev.B, gpio0 is reserved.
*/
&gpio1 {
- status = "ok";
+ status = "okay";
};
&gpio2 {
- status = "ok";
+ status = "okay";
};
&gpio3 {
- status = "ok";
+ status = "okay";
};
&gpio4 {
- status = "ok";
+ status = "okay";
};
&i2c0 {
- status = "ok";
+ status = "okay";
};
&i2c1 {
- status = "ok";
+ status = "okay";
};
&pcie0 {
- status = "ok";
+ status = "okay";
};
&spi0 {
- status = "ok";
+ status = "okay";
};
&spi1 {
- status = "ok";
+ status = "okay";
sdcard0: sdcard@0 {
compatible = "mmc-spi-slot";
reg = <0>;
@@ -45,38 +45,38 @@
};
&serial0 {
- status = "ok";
+ status = "okay";
};
&sata1 {
- status = "ok";
+ status = "okay";
};
&sata2 {
- status = "ok";
+ status = "okay";
};
&sata3 {
- status = "ok";
+ status = "okay";
};
&sgenet0 {
- status = "ok";
+ status = "okay";
};
&xgenet1 {
- status = "ok";
+ status = "okay";
};
&mmc0 {
- status = "ok";
+ status = "okay";
};
&i2c4 {
rtc68: rtc@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
- status = "ok";
+ status = "okay";
};
};
@@ -45,36 +45,36 @@
};
&pcie0clk {
- status = "ok";
+ status = "okay";
};
&pcie0 {
- status = "ok";
+ status = "okay";
};
&serial0 {
- status = "ok";
+ status = "okay";
};
&menet {
- status = "ok";
+ status = "okay";
};
&sgenet0 {
- status = "ok";
+ status = "okay";
};
&sgenet1 {
- status = "ok";
+ status = "okay";
};
&xgenet {
- status = "ok";
+ status = "okay";
rxlos-gpios = <&sbgpio 12 1>;
};
&mmc0 {
- status = "ok";
+ status = "okay";
};
&mdio {
@@ -270,7 +270,7 @@
reg = <0x0 0x1f22c000 0x0 0x1000>;
reg-names = "csr-reg";
clock-output-names = "sataphy2clk";
- status = "ok";
+ status = "okay";
csr-offset = <0x4>;
csr-mask = <0x3a>;
enable-offset = <0x0>;
@@ -284,7 +284,7 @@
reg = <0x0 0x1f23c000 0x0 0x1000>;
reg-names = "csr-reg";
clock-output-names = "sataphy3clk";
- status = "ok";
+ status = "okay";
csr-offset = <0x4>;
csr-mask = <0x3a>;
enable-offset = <0x0>;
@@ -864,7 +864,7 @@
reg = <0x0 0x1f22a000 0x0 0x100>;
#phy-cells = <1>;
clocks = <&sataphy2clk 0>;
- status = "ok";
+ status = "okay";
apm,tx-boost-gain = <30 30 30 30 30 30>;
apm,tx-eye-tuning = <1 10 10 2 10 10>;
};
@@ -874,7 +874,7 @@
reg = <0x0 0x1f23a000 0x0 0x100>;
#phy-cells = <1>;
clocks = <&sataphy3clk 0>;
- status = "ok";
+ status = "okay";
apm,tx-boost-gain = <31 31 31 31 31 31>;
apm,tx-eye-tuning = <2 10 10 2 10 10>;
};
@@ -903,7 +903,7 @@
<0x0 0x1f227000 0x0 0x1000>;
interrupts = <0x0 0x87 0x4>;
dma-coherent;
- status = "ok";
+ status = "okay";
clocks = <&sata23clk 0>;
phys = <&phy2 0>;
phy-names = "sata-phy";
@@ -917,7 +917,7 @@
<0x0 0x1f23e000 0x0 0x1000>;
interrupts = <0x0 0x88 0x4>;
dma-coherent;
- status = "ok";
+ status = "okay";
clocks = <&sata45clk 0>;
phys = <&phy3 0>;
phy-names = "sata-phy";
@@ -151,7 +151,7 @@
};
&nand {
- status = "ok";
+ status = "okay";
nandcs@0 {
compatible = "brcm,nandcs";
reg = <0>;
@@ -527,7 +527,7 @@
status = "okay";
adv7533: adv7533@39 {
- status = "ok";
+ status = "okay";
compatible = "adi,adv7533";
reg = <0x39>;
};
@@ -602,7 +602,7 @@
&sdio_cfg_func>;
/* WL_EN */
vmmc-supply = <&wlan_en>;
- status = "ok";
+ status = "okay";
wlcore: wlcore@2 {
compatible = "ti,wl1837";
@@ -418,7 +418,7 @@
&sdio_cfg_func>;
/* WL_EN */
vmmc-supply = <&wlan_en>;
- status = "ok";
+ status = "okay";
wlcore: wlcore@2 {
compatible = "ti,wl1837";
@@ -124,21 +124,21 @@
soc {
spi0: spi@f7106000 {
- status = "ok";
+ status = "okay";
};
i2c0: i2c@f7100000 {
- status = "ok";
+ status = "okay";
};
i2c1: i2c@f7101000 {
- status = "ok";
+ status = "okay";
};
uart1: uart@f7111000 {
assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
assigned-clock-rates = <150000000>;
- status = "ok";
+ status = "okay";
bluetooth {
compatible = "ti,wl1835-st";
@@ -149,11 +149,11 @@
};
uart2: uart@f7112000 {
- status = "ok";
+ status = "okay";
};
uart3: uart@f7113000 {
- status = "ok";
+ status = "okay";
};
/*
@@ -488,11 +488,11 @@
};
&ade {
- status = "ok";
+ status = "okay";
};
&dsi {
- status = "ok";
+ status = "okay";
ports {
/* 1 for output port */
@@ -509,7 +509,7 @@
&i2c2 {
#address-cells = <1>;
#size-cells = <0>;
- status = "ok";
+ status = "okay";
adv7533: adv7533@39 {
compatible = "adi,adv7533";
@@ -370,7 +370,7 @@
clocks = <&sys_ctrl HI6220_EDMAC_ACLK>;
dma-no-cci;
dma-type = "hi6220_dma";
- status = "ok";
+ status = "okay";
};
dual_timer0: timer@f8008000 {
@@ -42,15 +42,15 @@
};
&uart0 {
- status = "ok";
+ status = "okay";
};
&peri_gpio0 {
- status = "ok";
+ status = "okay";
};
&lbc {
- status = "ok";
+ status = "okay";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0x0 0x90000000 0x08000000>,
@@ -22,37 +22,37 @@
};
&ipmi0 {
- status = "ok";
+ status = "okay";
};
&uart0 {
- status = "ok";
+ status = "okay";
};
ð0 {
- status = "ok";
+ status = "okay";
};
ð1 {
- status = "ok";
+ status = "okay";
};
ð2 {
- status = "ok";
+ status = "okay";
};
ð3 {
- status = "ok";
+ status = "okay";
};
&sas1 {
- status = "ok";
+ status = "okay";
};
&usb_ohci {
- status = "ok";
+ status = "okay";
};
&usb_ehci {
- status = "ok";
+ status = "okay";
};
@@ -50,41 +50,41 @@
};
&uart0 {
- status = "ok";
+ status = "okay";
};
&ipmi0 {
- status = "ok";
+ status = "okay";
};
&usb_ohci {
- status = "ok";
+ status = "okay";
};
&usb_ehci {
- status = "ok";
+ status = "okay";
};
ð0 {
- status = "ok";
+ status = "okay";
};
ð1 {
- status = "ok";
+ status = "okay";
};
ð2 {
- status = "ok";
+ status = "okay";
};
ð3 {
- status = "ok";
+ status = "okay";
};
&sas1 {
- status = "ok";
+ status = "okay";
};
&p0_pcie2_a {
- status = "ok";
+ status = "okay";
};
@@ -27,11 +27,11 @@
soc {
serial@78b3000 {
- status = "ok";
+ status = "okay";
};
spi@78b5000 {
- status = "ok";
+ status = "okay";
m25p80@0 {
#address-cells = <1>;
@@ -43,19 +43,19 @@
};
serial@78b1000 {
- status = "ok";
+ status = "okay";
};
i2c@78b6000 {
- status = "ok";
+ status = "okay";
};
dma@7984000 {
- status = "ok";
+ status = "okay";
};
nand@79b0000 {
- status = "ok";
+ status = "okay";
nand@0 {
reg = <0>;
@@ -66,20 +66,20 @@
};
phy@86000 {
- status = "ok";
+ status = "okay";
};
phy@8e000 {
- status = "ok";
+ status = "okay";
};
pci@20000000 {
- status = "ok";
+ status = "okay";
perst-gpio = <&tlmm 58 0x1>;
};
pci@10000000 {
- status = "ok";
+ status = "okay";
perst-gpio = <&tlmm 61 0x1>;
};
};
@@ -13,7 +13,7 @@
};
ðernet {
- status = "ok";
+ status = "okay";
snps,reset-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>;
snps,reset-active-low;
@@ -79,7 +79,7 @@
};
&pcie {
- status = "ok";
+ status = "okay";
perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
@@ -88,22 +88,22 @@
};
&pcie_phy {
- status = "ok";
+ status = "okay";
vdda-vp-supply = <&vreg_l3_1p05>;
vdda-vph-supply = <&vreg_l5_1p8>;
};
&remoteproc_adsp {
- status = "ok";
+ status = "okay";
};
&remoteproc_cdsp {
- status = "ok";
+ status = "okay";
};
&remoteproc_wcss {
- status = "ok";
+ status = "okay";
};
&rpm_requests {
@@ -197,7 +197,7 @@
};
&sdcc1 {
- status = "ok";
+ status = "okay";
mmc-ddr-1_8v;
mmc-hs400-1_8v;
@@ -134,7 +134,7 @@
pinctrl-0 = <&rmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&i2c0 {
@@ -183,7 +183,7 @@
snps,reset-delays-us = <0 10000 1000000>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&i2c0 {
@@ -167,7 +167,7 @@
pinctrl-0 = <&rmii_pins>;
tx_delay = <0x30>;
rx_delay = <0x10>;
- status = "ok";
+ status = "okay";
};
&i2c0 {
@@ -198,7 +198,7 @@
};
&io_domains {
- status = "ok";
+ status = "okay";
audio-supply = <&vcc_io>;
gpio30-supply = <&vcc_io>;
@@ -130,11 +130,11 @@
ports {
port@0 {
label = "ethblack";
- status = "ok";
+ status = "okay";
};
port@4 {
label = "ethblue";
- status = "ok";
+ status = "okay";
};
};
};
@@ -13,9 +13,9 @@
};
&gmac1 {
- status = "ok";
+ status = "okay";
};
&phy_external {
- status = "ok";
+ status = "okay";
};
Cleanup status to use "okay" as the spec says. While Linux has supported "ok", would be nice to have in tree dts files to conform to the spec. Signed-off-by: Kumar Gala <kumar.gala@linaro.org> --- .../devicetree/bindings/csky/cpus.txt | 4 +-- .../bindings/display/hisilicon/dw-dsi.txt | 2 +- .../bindings/display/ti/ti,omap-dss.txt | 4 +-- .../bindings/net/apm-xgene-enet.txt | 4 +-- .../devicetree/bindings/net/dsa/sja1105.txt | 2 +- arch/arm/boot/dts/am3517-evm-ui.dtsi | 4 +-- arch/arm/boot/dts/am3517-evm.dts | 2 +- arch/arm/boot/dts/am437x-gp-evm.dts | 2 +- arch/arm/boot/dts/am437x-sbc-t43.dts | 2 +- arch/arm/boot/dts/am43x-epos-evm.dts | 2 +- .../boot/dts/am57xx-beagle-x15-common.dtsi | 6 ++-- arch/arm/boot/dts/am57xx-sbc-am57x.dts | 4 +-- arch/arm/boot/dts/armada-388-db.dts | 2 +- arch/arm/boot/dts/bcm958525xmc.dts | 2 +- arch/arm/boot/dts/bcm958625k.dts | 2 +- arch/arm/boot/dts/da850-evm.dts | 2 +- arch/arm/boot/dts/dove.dtsi | 2 +- arch/arm/boot/dts/dra7-evm.dts | 2 +- arch/arm/boot/dts/dra72-evm-common.dtsi | 6 ++-- arch/arm/boot/dts/efm32gg-dk3750.dts | 12 ++++---- arch/arm/boot/dts/efm32gg.dtsi | 2 +- arch/arm/boot/dts/hi3620-hi4511.dts | 12 ++++---- arch/arm/boot/dts/hip04-d01.dts | 2 +- arch/arm/boot/dts/keystone-k2e-evm.dts | 2 +- arch/arm/boot/dts/keystone-k2hk-evm.dts | 2 +- arch/arm/boot/dts/keystone-k2l-evm.dts | 2 +- arch/arm/boot/dts/kirkwood-dockstar.dts | 2 +- arch/arm/boot/dts/kirkwood-dreamplug.dts | 2 +- arch/arm/boot/dts/kirkwood-goflexnet.dts | 2 +- .../dts/kirkwood-guruplug-server-plus.dts | 2 +- arch/arm/boot/dts/kirkwood-iconnect.dts | 2 +- arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts | 2 +- arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi | 2 +- arch/arm/boot/dts/kirkwood.dtsi | 4 +-- .../boot/dts/logicpd-som-lv-baseboard.dtsi | 2 +- .../boot/dts/logicpd-torpedo-baseboard.dtsi | 2 +- arch/arm/boot/dts/omap3-beagle-xm.dts | 4 +-- arch/arm/boot/dts/omap3-beagle.dts | 6 ++-- arch/arm/boot/dts/omap3-cm-t3517.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3530.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3730.dts | 2 +- arch/arm/boot/dts/omap3-cm-t3x.dtsi | 4 +-- .../arm/boot/dts/omap3-devkit8000-common.dtsi | 4 +-- arch/arm/boot/dts/omap3-gta04.dtsi | 8 ++--- arch/arm/boot/dts/omap3-ha-lcd.dts | 2 +- arch/arm/boot/dts/omap3-igep0020-common.dtsi | 2 +- arch/arm/boot/dts/omap3-n900.dts | 6 ++-- arch/arm/boot/dts/omap3-n950.dts | 4 +-- arch/arm/boot/dts/omap3-overo-common-dvi.dtsi | 2 +- .../boot/dts/omap3-overo-common-lcd35.dtsi | 2 +- .../boot/dts/omap3-overo-common-lcd43.dtsi | 2 +- arch/arm/boot/dts/omap3-pandora-common.dtsi | 4 +-- .../dts/omap3-panel-sharp-ls037v7dw01.dtsi | 2 +- arch/arm/boot/dts/omap3-thunder.dts | 2 +- arch/arm/boot/dts/omap34xx.dtsi | 2 +- arch/arm/boot/dts/omap36xx.dtsi | 2 +- arch/arm/boot/dts/omap4-duovero-parlor.dts | 4 +-- arch/arm/boot/dts/omap4-panda-common.dtsi | 6 ++-- arch/arm/boot/dts/omap4-sdp.dts | 8 ++--- arch/arm/boot/dts/omap5-board-common.dtsi | 4 +-- arch/arm/boot/dts/omap5-cm-t54.dts | 6 ++-- .../arm/boot/dts/qcom-apq8060-dragonboard.dts | 12 ++++---- .../boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 8 ++--- arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts | 8 ++--- arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 10 +++---- .../dts/qcom-apq8064-sony-xperia-yuga.dts | 4 +-- .../arm/boot/dts/qcom-apq8074-dragonboard.dts | 10 +++---- arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 18 +++++------ .../boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts | 4 +-- arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi | 10 +++---- .../boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts | 8 ++--- .../boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts | 2 +- arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi | 10 +++---- arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 2 +- arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi | 12 ++++---- arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi | 16 +++++----- arch/arm/boot/dts/qcom-msm8660-surf.dts | 4 +-- arch/arm/boot/dts/qcom-msm8960-cdp.dts | 8 ++--- .../boot/dts/qcom-msm8974-fairphone-fp2.dts | 10 +++---- .../qcom-msm8974-lge-nexus5-hammerhead.dts | 30 +++++++++---------- .../boot/dts/qcom-msm8974-samsung-klte.dts | 2 +- .../dts/qcom-msm8974-sony-xperia-amami.dts | 14 ++++----- .../dts/qcom-msm8974-sony-xperia-castor.dts | 18 +++++------ .../dts/qcom-msm8974-sony-xperia-honami.dts | 12 ++++---- arch/arm/boot/dts/rk3288-evb.dtsi | 2 +- .../boot/dts/rk3288-firefly-reload-core.dtsi | 2 +- arch/arm/boot/dts/rk3288-firefly.dtsi | 2 +- arch/arm/boot/dts/rk3288-miqi.dts | 2 +- arch/arm/boot/dts/rk3288-popmetal.dts | 2 +- arch/arm/boot/dts/rk3288-r89.dts | 2 +- arch/arm/boot/dts/rk3288-rock2-square.dts | 2 +- arch/arm/boot/dts/rk3288-tinker.dtsi | 2 +- .../boot/dts/amd/amd-overdrive-rev-b0.dts | 22 +++++++------- .../boot/dts/amd/amd-overdrive-rev-b1.dts | 24 +++++++-------- arch/arm64/boot/dts/amd/amd-overdrive.dts | 14 ++++----- arch/arm64/boot/dts/amd/husky.dts | 20 ++++++------- arch/arm64/boot/dts/apm/apm-merlin.dts | 16 +++++----- arch/arm64/boot/dts/apm/apm-mustang.dts | 16 +++++----- arch/arm64/boot/dts/apm/apm-storm.dtsi | 12 ++++---- .../dts/broadcom/stingray/bcm958742-base.dtsi | 2 +- .../boot/dts/hisilicon/hi3660-hikey960.dts | 4 +-- .../boot/dts/hisilicon/hi3670-hikey970.dts | 2 +- .../arm64/boot/dts/hisilicon/hi6220-hikey.dts | 18 +++++------ arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 2 +- arch/arm64/boot/dts/hisilicon/hip05-d02.dts | 6 ++-- arch/arm64/boot/dts/hisilicon/hip06-d03.dts | 18 +++++------ arch/arm64/boot/dts/hisilicon/hip07-d05.dts | 20 ++++++------- arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 20 ++++++------- arch/arm64/boot/dts/qcom/qcs404-evb-4000.dts | 2 +- arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 12 ++++---- arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi | 2 +- .../dts/rockchip/rk3368-orion-r68-meta.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3368-r88.dts | 4 +-- drivers/staging/mt7621-dts/gbpc1.dts | 4 +-- drivers/staging/mt7621-dts/gbpc2.dts | 4 +-- 115 files changed, 349 insertions(+), 349 deletions(-) -- 2.20.1