@@ -21,6 +21,22 @@
};
};
+&pcie {
+ status = "ok";
+
+ perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&perst_state>;
+};
+
+&pcie_phy {
+ status = "ok";
+
+ vdda-vp-supply = <&vreg_l3_1p05>;
+ vdda-vph-supply = <&vreg_l5_1p8>;
+};
+
&remoteproc_adsp {
status = "ok";
};
@@ -137,6 +153,15 @@
};
&tlmm {
+ perst_state: perst {
+ pins = "gpio43";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
sdc1_on: sdc1-on {
clk {
pins = "sdc1_clk";
@@ -3,6 +3,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-qcs404.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
interrupt-parent = <&intc>;
@@ -377,6 +378,7 @@
compatible = "qcom,gcc-qcs404";
reg = <0x01800000 0x80000>;
#clock-cells = <1>;
+ #reset-cells = <1>;
assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
assigned-clock-rates = <19200000>;
@@ -405,6 +407,21 @@
#interrupt-cells = <4>;
};
+ pcie_phy: phy@7786000 {
+ compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+ reg = <0x07786000 0xb8>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+ <&gcc GCC_PCIE_0_PIPE_ARES>;
+ reset-names = "phy", "pipe";
+
+ clock-output-names = "pcie_0_pipe_clk";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
sdcc1: sdcc@7804000 {
compatible = "qcom,sdhci-msm-v5";
reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
@@ -771,6 +788,56 @@
status = "disabled";
};
};
+
+ pcie: pci@10000000 {
+ compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
+ reg = <0x10000000 0xf1d
+ 0x10000f20 0xa8
+ 0x07780000 0x2000
+ 0x10001000 0x2000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0 0x10003000 0 0x00010000 /* I/O */
+ 0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
+
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+ clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
+ clock-names = "iface", "aux", "master_bus", "slave_bus";
+
+ resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_BCR>,
+ <&gcc GCC_PCIE_0_AHB_ARES>;
+ reset-names = "axi_m",
+ "axi_s",
+ "axi_m_sticky",
+ "pipe_sticky",
+ "pwr",
+ "ahb";
+
+ phys = <&pcie_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
};
timer {
The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to the platform dtsi and enable them for the EVB with the perst gpio and analog supplies defined. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> --- arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++ arch/arm64/boot/dts/qcom/qcs404.dtsi | 67 ++++++++++++++++++++++++ 2 files changed, 92 insertions(+) -- 2.18.0