diff mbox series

[v3] net: ftgmac100: Request clock and set speed

Message ID 20171013041638.30763-1-joel@jms.id.au
State Accepted
Commit 4b70c62b9eafcee0505b440732d2e00c50f3085d
Headers show
Series [v3] net: ftgmac100: Request clock and set speed | expand

Commit Message

Joel Stanley Oct. 13, 2017, 4:16 a.m. UTC 
According to the ASPEED datasheet, gigabit speeds require a clock of
100MHz or higher. Other speeds require 25MHz or higher. This patch
configures a 100MHz clock if the system has a direct-attached
PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.

There appear to be no other upstream users of the FTGMAC100 driver it is
hard to know the clocking requirements of other platforms. Therefore a
conservative approach was taken with enabling clocks. If the platform is
not ASPEED, both requesting the clock and configuring the speed is
skipped.

Signed-off-by: Joel Stanley <joel@jms.id.au>

---
Andrew, can you please give this one a spin on hardware?

v3:
 - Fix errors from v2
v2:
 - only touch the clocks on Aspeed platforms
 - unconditionally call clk_unprepare_disable

 drivers/net/ethernet/faraday/ftgmac100.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

-- 
2.14.1

Comments

David Miller Oct. 16, 2017, 7:59 p.m. UTC | #1 
From: Joel Stanley <joel@jms.id.au>

Date: Fri, 13 Oct 2017 12:16:38 +0800

> Andrew, can you please give this one a spin on hardware?


I'm waiting on this...
Andrew Jeffery Oct. 17, 2017, 2 a.m. UTC | #2 
On Fri, 2017-10-13 at 12:16 +0800, Joel Stanley wrote:
> According to the ASPEED datasheet, gigabit speeds require a clock of

> 100MHz or higher. Other speeds require 25MHz or higher. This patch

> configures a 100MHz clock if the system has a direct-attached

> PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.

> 

> There appear to be no other upstream users of the FTGMAC100 driver it is

> hard to know the clocking requirements of other platforms. Therefore a

> conservative approach was taken with enabling clocks. If the platform is

> not ASPEED, both requesting the clock and configuring the speed is

> skipped.

> 

> Signed-off-by: Joel Stanley <joel@jms.id.au>


Tested on an AST2500 EVB and an OpenPOWER Palmetto (AST2400) machine.
Confirmed clock rates were nominally what was requested, and successfully
downloaded a 100MB test file.

Tested-by: Andrew Jeffery <andrew@aj.id.au>


> ---

> Andrew, can you please give this one a spin on hardware?

> 

> v3:

>  - Fix errors from v2

> v2:

>  - only touch the clocks on Aspeed platforms

>  - unconditionally call clk_unprepare_disable

> 

>  drivers/net/ethernet/faraday/ftgmac100.c | 26 ++++++++++++++++++++++++++

>  1 file changed, 26 insertions(+)

> 

> diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c

> index 9ed8e4b81530..78db8e62a83f 100644

> --- a/drivers/net/ethernet/faraday/ftgmac100.c

> +++ b/drivers/net/ethernet/faraday/ftgmac100.c

> @@ -21,6 +21,7 @@

>  

>  #define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt

>  

> +#include <linux/clk.h>

>  #include <linux/dma-mapping.h>

>  #include <linux/etherdevice.h>

>  #include <linux/ethtool.h>

> @@ -59,6 +60,9 @@

>  /* Min number of tx ring entries before stopping queue */

>  #define TX_THRESHOLD		(MAX_SKB_FRAGS + 1)

>  

> +#define FTGMAC_100MHZ		100000000

> +#define FTGMAC_25MHZ		25000000

> +

>  struct ftgmac100 {

>  	/* Registers */

>  	struct resource *res;

> @@ -96,6 +100,7 @@ struct ftgmac100 {

>  	struct napi_struct napi;

>  	struct work_struct reset_task;

>  	struct mii_bus *mii_bus;

> +	struct clk *clk;

>  

>  	/* Link management */

>  	int cur_speed;

> @@ -1734,6 +1739,22 @@ static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)

>  		    nd->link_up ? "up" : "down");

>  }

>  

> +static void ftgmac100_setup_clk(struct ftgmac100 *priv)

> +{

> +	priv->clk = devm_clk_get(priv->dev, NULL);

> +	if (IS_ERR(priv->clk))

> +		return;

> +

> +	clk_prepare_enable(priv->clk);

> +

> +	/* Aspeed specifies a 100MHz clock is required for up to

> +	 * 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz

> +	 * is sufficient

> +	 */

> +	clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :

> +			FTGMAC_100MHZ);

> +}

> +

>  static int ftgmac100_probe(struct platform_device *pdev)

>  {

>  	struct resource *res;

> @@ -1830,6 +1851,9 @@ static int ftgmac100_probe(struct platform_device *pdev)

>  			goto err_setup_mdio;

>  	}

>  

> +	if (priv->is_aspeed)

> +		ftgmac100_setup_clk(priv);

> +

>  	/* Default ring sizes */

>  	priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;

>  	priv->tx_q_entries = priv->new_tx_q_entries = DEF_TX_QUEUE_ENTRIES;

> @@ -1883,6 +1907,8 @@ static int ftgmac100_remove(struct platform_device *pdev)

>  

>  	unregister_netdev(netdev);

>  

> +	clk_disable_unprepare(priv->clk);

> +

>  	/* There's a small chance the reset task will have been re-queued,

>  	 * during stop, make sure it's gone before we free the structure.

>  	 */
David Miller Oct. 18, 2017, 11:09 a.m. UTC | #3 
From: Joel Stanley <joel@jms.id.au>

Date: Fri, 13 Oct 2017 12:16:38 +0800

> According to the ASPEED datasheet, gigabit speeds require a clock of

> 100MHz or higher. Other speeds require 25MHz or higher. This patch

> configures a 100MHz clock if the system has a direct-attached

> PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.

> 

> There appear to be no other upstream users of the FTGMAC100 driver it is

> hard to know the clocking requirements of other platforms. Therefore a

> conservative approach was taken with enabling clocks. If the platform is

> not ASPEED, both requesting the clock and configuring the speed is

> skipped.

> 

> Signed-off-by: Joel Stanley <joel@jms.id.au>


Applied to net-next, thanks.
diff mbox series

Patch

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 9ed8e4b81530..78db8e62a83f 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -21,6 +21,7 @@ 
 
 #define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
 
+#include <linux/clk.h>
 #include <linux/dma-mapping.h>
 #include <linux/etherdevice.h>
 #include <linux/ethtool.h>
@@ -59,6 +60,9 @@ 
 /* Min number of tx ring entries before stopping queue */
 #define TX_THRESHOLD		(MAX_SKB_FRAGS + 1)
 
+#define FTGMAC_100MHZ		100000000
+#define FTGMAC_25MHZ		25000000
+
 struct ftgmac100 {
 	/* Registers */
 	struct resource *res;
@@ -96,6 +100,7 @@  struct ftgmac100 {
 	struct napi_struct napi;
 	struct work_struct reset_task;
 	struct mii_bus *mii_bus;
+	struct clk *clk;
 
 	/* Link management */
 	int cur_speed;
@@ -1734,6 +1739,22 @@  static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)
 		    nd->link_up ? "up" : "down");
 }
 
+static void ftgmac100_setup_clk(struct ftgmac100 *priv)
+{
+	priv->clk = devm_clk_get(priv->dev, NULL);
+	if (IS_ERR(priv->clk))
+		return;
+
+	clk_prepare_enable(priv->clk);
+
+	/* Aspeed specifies a 100MHz clock is required for up to
+	 * 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz
+	 * is sufficient
+	 */
+	clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
+			FTGMAC_100MHZ);
+}
+
 static int ftgmac100_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -1830,6 +1851,9 @@  static int ftgmac100_probe(struct platform_device *pdev)
 			goto err_setup_mdio;
 	}
 
+	if (priv->is_aspeed)
+		ftgmac100_setup_clk(priv);
+
 	/* Default ring sizes */
 	priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;
 	priv->tx_q_entries = priv->new_tx_q_entries = DEF_TX_QUEUE_ENTRIES;
@@ -1883,6 +1907,8 @@  static int ftgmac100_remove(struct platform_device *pdev)
 
 	unregister_netdev(netdev);
 
+	clk_disable_unprepare(priv->clk);
+
 	/* There's a small chance the reset task will have been re-queued,
 	 * during stop, make sure it's gone before we free the structure.
 	 */