@@ -13,6 +13,7 @@ config AB8500_USB
tristate "AB8500 USB Transceiver Driver"
depends on AB8500_CORE
select USB_PHY
+ select EXTCON
help
Enable this to support the USB OTG transceiver in AB8500 chip.
This transceiver supports high and full speed devices plus,
@@ -23,6 +24,7 @@ config FSL_USB2_OTG
depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
+ select EXTCON
help
Enable this to support Freescale USB OTG transceiver.
@@ -32,6 +34,7 @@ config ISP1301_OMAP
depends on USB
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
+ select EXTCON
help
If you say yes here you get support for the Philips ISP1301
USB-On-The-Go transceiver working with the OMAP OTG controller.
@@ -55,6 +58,7 @@ config NOP_USB_XCEIV
tristate "NOP USB Transceiver Driver"
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
select USB_PHY
+ select EXTCON
help
This driver is to be used by all the usb transceiver which are either
built-in with usb ip or which are autonomous and doesn't require any
@@ -70,6 +74,7 @@ config AM335X_PHY_USB
select USB_PHY
select AM335X_CONTROL_USB
select USB_COMMON
+ select EXTCON
help
This driver provides PHY support for that phy which part for the
AM335x SoC.
@@ -98,6 +103,7 @@ config USB_GPIO_VBUS
depends on GPIOLIB || COMPILE_TEST
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
+ select EXTCON
help
Provides simple GPIO VBUS sensing for controllers with an
internal transceiver via the usb_phy interface, and
@@ -116,9 +122,10 @@ config OMAP_OTG
config TAHVO_USB
tristate "Tahvo USB transceiver driver"
- depends on MFD_RETU && EXTCON
+ depends on MFD_RETU
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
+ select EXTCON
help
Enable this to support USB transceiver on Tahvo. This is used
at least on Nokia 770.
@@ -135,6 +142,7 @@ config USB_ISP1301
depends on USB || USB_GADGET
depends on I2C
select USB_PHY
+ select EXTCON
help
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
This chip is typically used as USB transceiver for USB host, gadget
@@ -148,8 +156,8 @@ config USB_MSM_OTG
depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
depends on RESET_CONTROLLER
- depends on EXTCON
select USB_PHY
+ select EXTCON
help
Enable this to support the USB OTG transceiver on Qualcomm chips. It
handles PHY initialization, clock management, and workarounds
@@ -162,9 +170,10 @@ config USB_MSM_OTG
config USB_QCOM_8X16_PHY
tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
depends on ARCH_QCOM || COMPILE_TEST
- depends on RESET_CONTROLLER && EXTCON
+ depends on RESET_CONTROLLER
select USB_PHY
select USB_ULPI_VIEWPORT
+ select EXTCON
help
Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
It handles PHY initialization, clock management, power management,
@@ -178,6 +187,7 @@ config USB_MV_OTG
depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
select USB_PHY
+ select EXTCON
help
Say Y here if you want to build Marvell USB OTG transciever
driver in kernel (including PXA and MMP series). This driver
@@ -190,6 +200,7 @@ config USB_MXS_PHY
depends on ARCH_MXC || ARCH_MXS
select STMP_DEVICE
select USB_PHY
+ select EXTCON
help
Enable this to support the Freescale MXS USB PHY.
@@ -100,6 +100,41 @@ static int devm_usb_phy_match(struct device *dev, void *res, void *match_data)
return *phy == match_data;
}
+static int usb_add_extcon(struct usb_phy *x)
+{
+ int ret;
+
+ if (of_property_read_bool(x->dev->of_node, "extcon")) {
+ x->edev = extcon_get_edev_by_phandle(x->dev, 0);
+ if (IS_ERR(x->edev))
+ return PTR_ERR(x->edev);
+
+ if (x->vbus_nb.notifier_call) {
+ ret = devm_extcon_register_notifier(x->dev, x->edev,
+ EXTCON_USB,
+ &x->vbus_nb);
+ if (ret < 0) {
+ dev_err(x->dev,
+ "register VBUS notifier failed\n");
+ return ret;
+ }
+ }
+
+ if (x->id_nb.notifier_call) {
+ ret = devm_extcon_register_notifier(x->dev, x->edev,
+ EXTCON_USB_HOST,
+ &x->id_nb);
+ if (ret < 0) {
+ dev_err(x->dev,
+ "register ID notifier failed\n");
+ return ret;
+ }
+ }
+ }
+
+ return 0;
+}
+
/**
* devm_usb_get_phy - find the USB PHY
* @dev - device that requests this phy
@@ -388,6 +423,10 @@ int usb_add_phy(struct usb_phy *x, enum usb_phy_type type)
return -EINVAL;
}
+ ret = usb_add_extcon(x);
+ if (ret)
+ return ret;
+
ATOMIC_INIT_NOTIFIER_HEAD(&x->notifier);
spin_lock_irqsave(&phy_lock, flags);
@@ -422,12 +461,17 @@ int usb_add_phy_dev(struct usb_phy *x)
{
struct usb_phy_bind *phy_bind;
unsigned long flags;
+ int ret;
if (!x->dev) {
dev_err(x->dev, "no device provided for PHY\n");
return -EINVAL;
}
+ ret = usb_add_extcon(x);
+ if (ret)
+ return ret;
+
ATOMIC_INIT_NOTIFIER_HEAD(&x->notifier);
spin_lock_irqsave(&phy_lock, flags);
@@ -9,6 +9,7 @@
#ifndef __LINUX_USB_PHY_H
#define __LINUX_USB_PHY_H
+#include <linux/extcon.h>
#include <linux/notifier.h>
#include <linux/usb.h>
@@ -85,6 +86,11 @@ struct usb_phy {
struct usb_phy_io_ops *io_ops;
void __iomem *io_priv;
+ /* to support extcon device */
+ struct extcon_dev *edev;
+ struct notifier_block vbus_nb;
+ struct notifier_block id_nb;
+
/* for notification of usb_phy_events */
struct atomic_notifier_head notifier;
Usually usb phy need register one extcon device to get the connection notifications. It will remove some duplicate code if the extcon device is registered using common code instead of each phy driver having its own related extcon APIs. So we add one pointer of extcon device into usb phy structure, and some other helper functions to register extcon. Suggested-by: NeilBrown <neilb@suse.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> --- drivers/usb/phy/Kconfig | 17 ++++++++++++++--- drivers/usb/phy/phy.c | 44 ++++++++++++++++++++++++++++++++++++++++++++ include/linux/usb/phy.h | 6 ++++++ 3 files changed, 64 insertions(+), 3 deletions(-) -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html