| Message ID | 1485436049-19754-7-git-send-email-rogerq@ti.com |
|---|---|
| State | New |
| Headers | show |
| Series | am57xx-idk LCD and am571x-idk 6 port ethernet pinmux | expand |
On Thu, Jan 26, 2017 at 03:07:28PM +0200, Roger Quadros wrote: > PRU ethernet MAC address range is present in the > board EEPROM. Parse it and setup eth?addr > environment variables. [snip] > +#ifdef CONFIG_BOARD_LATE_INIT > +int board_late_init(void) > +{ > + __maybe_unused int rc; > + > +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT) Just move the #if up to include 'int rc' and we don't need to declare it __maybe_unused then. [snip] > +/* Board Detection EEPROM */ > +#define CONFIG_EEPROM_BUS_ADDRESS 0 > +#define CONFIG_EEPROM_CHIP_ADDRESS 0x50 Only dra7xx and am57xx use these CONFIG options currently, please migrate them to Kconfig instead of adding another board, thanks! -- Tom _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
On 26/01/17 19:41, Tom Rini wrote: > On Thu, Jan 26, 2017 at 03:07:28PM +0200, Roger Quadros wrote: > >> PRU ethernet MAC address range is present in the >> board EEPROM. Parse it and setup eth?addr >> environment variables. > [snip] >> +#ifdef CONFIG_BOARD_LATE_INIT >> +int board_late_init(void) >> +{ >> + __maybe_unused int rc; >> + >> +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT) > > Just move the #if up to include 'int rc' and we don't need to declare it > __maybe_unused then. OK. > > [snip] >> +/* Board Detection EEPROM */ >> +#define CONFIG_EEPROM_BUS_ADDRESS 0 >> +#define CONFIG_EEPROM_CHIP_ADDRESS 0x50 > > Only dra7xx and am57xx use these CONFIG options currently, please > migrate them to Kconfig instead of adding another board, thanks! > I didn't get this part. In this patch board_k2g.c is using those macros. Are you suggesting to move this to Kconfig instead of putting them in the board headers? cheers, -roger _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
On Fri, Jan 27, 2017 at 10:58:41AM +0200, Roger Quadros wrote: > > On 26/01/17 19:41, Tom Rini wrote: > > On Thu, Jan 26, 2017 at 03:07:28PM +0200, Roger Quadros wrote: > > > >> PRU ethernet MAC address range is present in the > >> board EEPROM. Parse it and setup eth?addr > >> environment variables. > > [snip] > >> +#ifdef CONFIG_BOARD_LATE_INIT > >> +int board_late_init(void) > >> +{ > >> + __maybe_unused int rc; > >> + > >> +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT) > > > > Just move the #if up to include 'int rc' and we don't need to declare it > > __maybe_unused then. > > OK. > > > > [snip] > >> +/* Board Detection EEPROM */ > >> +#define CONFIG_EEPROM_BUS_ADDRESS 0 > >> +#define CONFIG_EEPROM_CHIP_ADDRESS 0x50 > > > > Only dra7xx and am57xx use these CONFIG options currently, please > > migrate them to Kconfig instead of adding another board, thanks! > > > > I didn't get this part. In this patch board_k2g.c is using those macros. > Are you suggesting to move this to Kconfig instead of putting them > in the board headers? Correct, move them to Kconfig (and migrate the other two boards). Thanks! -- Tom _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
diff --git a/board/ti/ks2_evm/board_k2g.c b/board/ti/ks2_evm/board_k2g.c index 40edbaa..64a62e0 100644 --- a/board/ti/ks2_evm/board_k2g.c +++ b/board/ti/ks2_evm/board_k2g.c @@ -12,6 +12,7 @@ #include <asm/arch/psc_defs.h> #include <asm/arch/mmc_host_def.h> #include "mux-k2g.h" +#include "../common/board_detect.h" #define SYS_CLK 24000000 @@ -149,6 +150,24 @@ int board_early_init_f(void) } #endif +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + __maybe_unused int rc; + +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT) + rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, + CONFIG_EEPROM_CHIP_ADDRESS); + if (rc) + printf("ti_i2c_eeprom_init failed %d\n", rc); + + board_ti_set_ethaddr(1); +#endif + + return 0; +} +#endif + #ifdef CONFIG_SPL_BUILD void spl_init_keystone_plls(void) { diff --git a/include/configs/k2g_evm.h b/include/configs/k2g_evm.h index 81da8ff..f37dbfd 100644 --- a/include/configs/k2g_evm.h +++ b/include/configs/k2g_evm.h @@ -53,6 +53,10 @@ /* NAND Configuration */ #define CONFIG_SYS_NAND_PAGE_2K +/* Board Detection EEPROM */ +#define CONFIG_EEPROM_BUS_ADDRESS 0 +#define CONFIG_EEPROM_CHIP_ADDRESS 0x50 + /* Network */ #define CONFIG_KSNET_NETCP_V1_5 #define CONFIG_KSNET_CPSW_NUM_PORTS 2
PRU ethernet MAC address range is present in the board EEPROM. Parse it and setup eth?addr environment variables. Signed-off-by: Roger Quadros <rogerq@ti.com> --- board/ti/ks2_evm/board_k2g.c | 19 +++++++++++++++++++ include/configs/k2g_evm.h | 4 ++++ 2 files changed, 23 insertions(+) -- 2.7.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot