| Message ID | 1434383399-2370-13-git-send-email-vaibhav.hiremath@linaro.org |
|---|---|
| State | New |
| Headers | show |
On Tuesday 16 June 2015 06:52 PM, Rob Herring wrote: > On Mon, Jun 15, 2015 at 10:49 AM, Vaibhav Hiremath > <vaibhav.hiremath@linaro.org> wrote: >> With addition of PXA910 family of devices, the TWSI module supports >> new feature which allows us to adjust SCLK. >> With DT properties i2c-pxa driver takes input configuration >> in nsec and converts it to respective bit-fields, >> >> - i2c-sclk-low-time-ns : SCLK low time (tlow) >> This property is used along with mode selection. >> - i2c-sclk-high-time-ns : SCLK high time (thigh) >> >> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org> >> --- >> Documentation/devicetree/bindings/i2c/i2c-pxa.txt | 13 +++++++++++++ >> 1 file changed, 13 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt >> index 9657db5..0fafd91 100644 >> --- a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt >> +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt >> @@ -23,12 +23,25 @@ Optional properties : >> - i2c-disable-after-xfer : If set, driver will disable I2C module >> after msg xfer and enable it again before xfer. >> >> + (Applicable to PXA910 family): >> + >> + - i2c-sclk-low-time-ns : SCLK low time (tlow), for standard/fast/high >> + speed mode. >> + This property is used along with mode selection. Driver uses this property >> + to set low/high time for standard and fast speed mode, as counter bit-field >> + is same for both. > > This belongs below both properties, and it should be clear that both > properties are required if present. > Technically, both properties are required only in case of high_mode. As mentioned above, in case of standard and fast mode we use tLow value. Thanks, Vaibhav -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 9657db5..0fafd91 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -23,12 +23,25 @@ Optional properties : - i2c-disable-after-xfer : If set, driver will disable I2C module after msg xfer and enable it again before xfer. + (Applicable to PXA910 family): + + - i2c-sclk-low-time-ns : SCLK low time (tlow), for standard/fast/high + speed mode. + This property is used along with mode selection. Driver uses this property + to set low/high time for standard and fast speed mode, as counter bit-field + is same for both. + - i2c-sclk-high-time-ns : SCLK high time (thigh), Used in case of high speed + mode. + Examples: twsi1: i2c@d4011000 { compatible = "mrvl,mmp-twsi"; reg = <0xd4011000 0x1000>; interrupts = <7>; mrvl,i2c-fast-mode; + + i2c-sclk-low-time-ns = <988>; + i2c-sclk-high-time-ns = <988>; }; twsi2: i2c@d4025000 {
With addition of PXA910 family of devices, the TWSI module supports new feature which allows us to adjust SCLK. With DT properties i2c-pxa driver takes input configuration in nsec and converts it to respective bit-fields, - i2c-sclk-low-time-ns : SCLK low time (tlow) This property is used along with mode selection. - i2c-sclk-high-time-ns : SCLK high time (thigh) Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org> --- Documentation/devicetree/bindings/i2c/i2c-pxa.txt | 13 +++++++++++++ 1 file changed, 13 insertions(+)