@@ -513,4 +513,11 @@ config MTD_NAND_XWAY
Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
to the External Bus Unit (EBU).
+config MTD_NAND_STM_BCH
+ tristate "STMicroelectronics: NANDi BCH Controller"
+ depends on ARCH_STI
+ depends on OF
+ help
+ Adds support for the STMicroelectronics NANDi BCH Controller.
+
endif # MTD_NAND
@@ -46,6 +46,7 @@ obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o
obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
obj-$(CONFIG_MTD_NAND_RICOH) += r852.o
obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
+obj-$(CONFIG_MTD_NAND_STM_BCH) += stm_nand_bch.o stm_nand_dt.o
obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/
obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
new file mode 100644
@@ -0,0 +1,1614 @@
+/*
+ * Support for STMicroelectronics NANDi BCH Controller
+ *
+ * Copyright (c) 2014 STMicroelectronics Limited
+ *
+ * Authors: Angus Clark <Angus.Clark@st.com>
+ * Lee Jones <lee.jones@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/completion.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/stm_nand_bbt.h>
+#include <linux/mtd/stm_nand.h>
+#include <linux/mtd/partitions.h>
+
+#include "stm_nand_dt.h"
+#include "stm_nand_regs.h"
+
+/* NANDi BCH Controller properties */
+#define NANDI_BCH_SECTOR_SIZE 1024
+#define NANDI_BCH_DMA_ALIGNMENT 64
+#define NANDI_BCH_MAX_BUF_LIST 8
+#define NANDI_BCH_BUF_LIST_SIZE (4 * NANDI_BCH_MAX_BUF_LIST)
+
+/* ONFI define 6 timing modes */
+#define ST_NAND_ONFI_TIMING_MODES 6
+
+#define PICO_TO_MILI(pico) (pico / 1000)
+
+static int bch_ecc_strength[] = {
+ [BCH_18BIT_ECC] = 18,
+ [BCH_30BIT_ECC] = 30,
+ [BCH_NO_ECC] = 0,
+};
+
+/* BCH 'program' structure */
+struct bch_prog {
+ u32 multi_cs_addr[3];
+ u32 multi_cs_config;
+ u8 seq[16];
+ u32 addr;
+ u32 extra;
+ u8 cmd[4];
+ u32 reserved1;
+ u32 gen_cfg;
+ u32 delay;
+ u32 reserved2;
+ u32 seq_cfg;
+};
+
+/* BCH template programs (modified on-the-fly) */
+static struct bch_prog bch_prog_read_page = {
+ .cmd = {
+ NAND_CMD_READ0,
+ NAND_CMD_READSTART,
+ },
+ .seq = {
+ BCH_ECC_SCORE(0),
+ BCH_CMD_ADDR,
+ BCH_CL_CMD_1,
+ BCH_DATA_2_SECTOR,
+ BCH_STOP,
+ },
+ .gen_cfg = (GEN_CFG_DATA_8_NOT_16 |
+ GEN_CFG_EXTRA_ADD_CYCLE |
+ GEN_CFG_LAST_SEQ_NODE),
+ .seq_cfg = SEQ_CFG_GO_STOP,
+};
+
+static struct bch_prog bch_prog_write_page = {
+ .cmd = {
+ NAND_CMD_SEQIN,
+ NAND_CMD_PAGEPROG,
+ NAND_CMD_STATUS,
+ },
+ .seq = {
+ BCH_CMD_ADDR,
+ BCH_DATA_4_SECTOR,
+ BCH_CL_CMD_1,
+ BCH_CL_CMD_2,
+ BCH_OP_ERR,
+ BCH_STOP,
+ },
+ .gen_cfg = (GEN_CFG_DATA_8_NOT_16 |
+ GEN_CFG_EXTRA_ADD_CYCLE |
+ GEN_CFG_LAST_SEQ_NODE),
+ .seq_cfg = (SEQ_CFG_GO_STOP |
+ SEQ_CFG_DATA_WRITE),
+};
+
+static struct bch_prog bch_prog_erase_block = {
+ .seq = {
+ BCH_CL_CMD_1,
+ BCH_AL_EX_0,
+ BCH_AL_EX_1,
+ BCH_AL_EX_2,
+ BCH_CL_CMD_2,
+ BCH_CL_CMD_3,
+ BCH_OP_ERR,
+ BCH_STOP,
+ },
+ .cmd = {
+ NAND_CMD_ERASE1,
+ NAND_CMD_ERASE1,
+ NAND_CMD_ERASE2,
+ NAND_CMD_STATUS,
+ },
+ .gen_cfg = (GEN_CFG_DATA_8_NOT_16 |
+ GEN_CFG_EXTRA_ADD_CYCLE |
+ GEN_CFG_LAST_SEQ_NODE),
+ .seq_cfg = (SEQ_CFG_GO_STOP |
+ SEQ_CFG_ERASE),
+};
+
+/* Configure BCH read/write/erase programs */
+static void bch_configure_progs(struct nandi_controller *nandi)
+{
+ uint8_t data_opa = ffs(nandi->sectors_per_page) - 1;
+ uint8_t data_instr = BCH_INSTR(BCH_OPC_DATA, data_opa);
+ uint32_t gen_cfg_ecc = nandi->bch_ecc_mode << GEN_CFG_ECC_SHIFT;
+
+ /* Set 'DATA' instruction */
+ bch_prog_read_page.seq[3] = data_instr;
+ bch_prog_write_page.seq[1] = data_instr;
+
+ /* Set ECC mode */
+ bch_prog_read_page.gen_cfg |= gen_cfg_ecc;
+ bch_prog_write_page.gen_cfg |= gen_cfg_ecc;
+ bch_prog_erase_block.gen_cfg |= gen_cfg_ecc;
+
+ /*
+ * Template sequences above are defined for devices that use 5 address
+ * cycles for page Read/Write operations (and 3 for Erase operations).
+ * Update sequences for devices that use 4 address cycles.
+ */
+ if (!nandi->extra_addr) {
+ /* Clear 'GEN_CFG_EXTRA_ADD_CYCLE' flag */
+ bch_prog_read_page.gen_cfg &= ~GEN_CFG_EXTRA_ADD_CYCLE;
+ bch_prog_write_page.gen_cfg &= ~GEN_CFG_EXTRA_ADD_CYCLE;
+ bch_prog_erase_block.gen_cfg &= ~GEN_CFG_EXTRA_ADD_CYCLE;
+
+ /* Configure Erase sequence for 2 address cycles */
+ /* (page address) */
+ bch_prog_erase_block.seq[0] = BCH_CL_CMD_1;
+ bch_prog_erase_block.seq[1] = BCH_AL_EX_0;
+ bch_prog_erase_block.seq[2] = BCH_AL_EX_1;
+ bch_prog_erase_block.seq[3] = BCH_CL_CMD_2;
+ bch_prog_erase_block.seq[4] = BCH_CL_CMD_3;
+ bch_prog_erase_block.seq[5] = BCH_OP_ERR;
+ bch_prog_erase_block.seq[6] = BCH_STOP;
+ }
+}
+
+/*
+ * NANDi Interrupts (shared by Hamming and BCH controllers)
+ */
+static irqreturn_t nandi_irq_handler(int irq, void *dev)
+{
+ struct nandi_controller *nandi = dev;
+ unsigned int status;
+
+ status = readl(nandi->base + NANDBCH_INT_STA);
+
+ if (nandi->bch_ecc_mode && (status & NANDBCH_INT_SEQNODESOVER)) {
+ /* BCH */
+ writel(NANDBCH_INT_CLR_SEQNODESOVER,
+ nandi->base + NANDBCH_INT_CLR);
+ complete(&nandi->seq_completed);
+ return IRQ_HANDLED;
+ }
+ if (status & NAND_INT_RBN) {
+ /* Hamming */
+ writel(NAND_INT_CLR_RBN, nandi->base + NANDHAM_INT_CLR);
+ complete(&nandi->rbn_completed);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static void nandi_enable_interrupts(struct nandi_controller *nandi,
+ uint32_t irqs)
+{
+ uint32_t val;
+
+ val = readl(nandi->base + NANDBCH_INT_EN);
+ val |= irqs;
+ writel(val, nandi->base + NANDBCH_INT_EN);
+}
+
+static void nandi_disable_interrupts(struct nandi_controller *nandi,
+ uint32_t irqs)
+{
+ uint32_t val;
+
+ val = readl(nandi->base + NANDBCH_INT_EN);
+ val &= ~irqs;
+ writel(val, nandi->base + NANDBCH_INT_EN);
+}
+
+/*
+ * BCH Operations
+ */
+static inline void bch_load_prog_cpu(struct nandi_controller *nandi,
+ struct bch_prog *prog)
+{
+ uint32_t *src = (uint32_t *)prog;
+ uint32_t *dst = (uint32_t *)(nandi->base + NANDBCH_ADDRESS_REG_1);
+ int i;
+
+ for (i = 0; i < 16; i++) {
+ /* Skip registers marked as "reserved" */
+ if (i != 11 && i != 14)
+ writel(*src, dst);
+ dst++;
+ src++;
+ }
+}
+
+static void bch_wait_seq(struct nandi_controller *nandi)
+{
+ int ret;
+
+ ret = wait_for_completion_timeout(&nandi->seq_completed, HZ/2);
+ if (!ret)
+ dev_err(nandi->dev, "BCH Seq timeout\n");
+}
+
+uint8_t bch_erase_block(struct nandi_controller *nandi,
+ loff_t offs)
+{
+ struct nand_chip *chip = &nandi->info.chip;
+ struct bch_prog *prog = &bch_prog_erase_block;
+ uint8_t status;
+
+ dev_dbg(nandi->dev, "%s: offs = 0x%012llx\n", __func__, offs);
+
+ prog->extra = (uint32_t)(offs >> chip->page_shift);
+
+ emiss_nandi_select(nandi, STM_NANDI_BCH);
+
+ nandi_enable_interrupts(nandi, NANDBCH_INT_SEQNODESOVER);
+ reinit_completion(&nandi->seq_completed);
+
+ bch_load_prog_cpu(nandi, prog);
+
+ bch_wait_seq(nandi);
+
+ nandi_disable_interrupts(nandi, NANDBCH_INT_SEQNODESOVER);
+
+ status = (uint8_t)(readl(nandi->base +
+ NANDBCH_CHECK_STATUS_REG_A) & 0xff);
+
+ return status;
+}
+EXPORT_SYMBOL(bch_erase_block);
+
+static int bch_erase(struct mtd_info *mtd, int page)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nandi_controller *nandi = chip->priv;
+ uint32_t page_size = mtd->writesize;
+ loff_t offs = (loff_t)page * page_size;
+
+ return bch_erase_block(nandi, offs);
+}
+
+/*
+ * Detect an erased page, tolerating and correcting up to a specified number of
+ * bits at '0'. (For many devices, it is now deemed within spec for an erased
+ * page to include a number of bits at '0', either as a result of read-disturb
+ * behaviour or 'stuck-at-zero' failures.) Returns the number of corrected
+ * bits, or a '-1' if we have exceeded the maximum number of bits at '0' (likely
+ * to be a genuine uncorrectable ECC error). In the latter case, the data must
+ * be returned unmodified, in accordance with the MTD API.
+ */
+static int check_erased_page(uint8_t *data, uint32_t page_size, int max_zeros)
+{
+ uint8_t *b = data;
+ int zeros = 0;
+ int i;
+
+ for (i = 0; i < page_size; i++) {
+ zeros += hweight8(~*b++);
+ if (zeros > max_zeros)
+ return -1;
+ }
+
+ if (zeros)
+ memset(data, 0xff, page_size);
+
+ return zeros;
+}
+
+/* Returns the number of ECC errors, or '-1' for uncorrectable error */
+int bch_read_page(struct nandi_controller *nandi,
+ loff_t offs,
+ uint8_t *buf)
+{
+ struct nand_chip *chip = &nandi->info.chip;
+ struct bch_prog *prog = &bch_prog_read_page;
+ uint32_t page_size = nandi->info.mtd.writesize;
+ unsigned long list_phys;
+ unsigned long buf_phys;
+ uint32_t ecc_err;
+ int ret = 0;
+
+ dev_dbg(nandi->dev, "%s: offs = 0x%012llx\n", __func__, offs);
+
+ BUG_ON(offs & (NANDI_BCH_DMA_ALIGNMENT - 1));
+
+ emiss_nandi_select(nandi, STM_NANDI_BCH);
+
+ nandi_enable_interrupts(nandi, NANDBCH_INT_SEQNODESOVER);
+ reinit_completion(&nandi->seq_completed);
+
+ /* Reset ECC stats */
+ writel(CFG_RESET_ECC_ALL | CFG_ENABLE_AFM,
+ nandi->base + NANDBCH_CONTROLLER_CFG);
+ writel(CFG_ENABLE_AFM, nandi->base + NANDBCH_CONTROLLER_CFG);
+
+ prog->addr = (uint32_t)((offs >> (chip->page_shift - 8)) & 0xffffff00);
+
+ buf_phys = dma_map_single(NULL, buf, page_size, DMA_FROM_DEVICE);
+
+ memset(nandi->buf_list, 0x00, NANDI_BCH_BUF_LIST_SIZE);
+ nandi->buf_list[0] = buf_phys | (nandi->sectors_per_page - 1);
+
+ list_phys = dma_map_single(NULL, nandi->buf_list,
+ NANDI_BCH_BUF_LIST_SIZE, DMA_TO_DEVICE);
+
+ writel(list_phys, nandi->base + NANDBCH_BUFFER_LIST_PTR);
+
+ bch_load_prog_cpu(nandi, prog);
+
+ bch_wait_seq(nandi);
+
+ nandi_disable_interrupts(nandi, NANDBCH_INT_SEQNODESOVER);
+
+ dma_unmap_single(NULL, list_phys, NANDI_BCH_BUF_LIST_SIZE,
+ DMA_TO_DEVICE);
+ dma_unmap_single(NULL, buf_phys, page_size, DMA_FROM_DEVICE);
+
+ /* Use the maximum per-sector ECC count! */
+ ecc_err = readl(nandi->base + NANDBCH_ECC_SCORE_REG_A) & 0xff;
+ if (ecc_err == 0xff) {
+ /*
+ * Downgrade uncorrectable ECC error for an erased page,
+ * tolerating 'bch_ecc_strength' bits at zero.
+ */
+ ret = check_erased_page(buf, page_size, chip->ecc.strength);
+ if (ret >= 0)
+ dev_dbg(nandi->dev,
+ "%s: erased page detected: \n"
+ " downgrading uncorrectable ECC error.\n",
+ __func__);
+ } else {
+ ret = (int)ecc_err;
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL(bch_read_page);
+
+static int bch_read(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ struct nandi_controller *nandi = chip->priv;
+ uint32_t page_size = mtd->writesize;
+ loff_t offs = (loff_t)page * page_size;
+ bool bounce = false;
+ uint8_t *p;
+ int ret;
+
+ if (((unsigned int)buf & (NANDI_BCH_DMA_ALIGNMENT - 1)) ||
+ (!virt_addr_valid(buf))) /* vmalloc'd buffer! */
+ bounce = true;
+
+ p = bounce ? nandi->page_buf : buf;
+
+ ret = bch_read_page(nandi, offs, p);
+ if (ret < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += ret;
+
+ if (bounce)
+ memcpy(buf, p, page_size);
+
+ return ret;
+}
+
+/* Returns the status of the NAND device following the write operation */
+uint8_t bch_write_page(struct nandi_controller *nandi,
+ loff_t offs, const uint8_t *buf)
+{
+ struct nand_chip *chip = &nandi->info.chip;
+ struct bch_prog *prog = &bch_prog_write_page;
+ uint32_t page_size = nandi->info.mtd.writesize;
+ uint8_t *p = (uint8_t *)buf;
+ unsigned long list_phys;
+ unsigned long buf_phys;
+ uint8_t status;
+ bool bounce = false;
+
+ dev_dbg(nandi->dev, "%s: offs = 0x%012llx\n", __func__, offs);
+
+ BUG_ON(offs & (page_size - 1));
+
+ if (((unsigned long)buf & (NANDI_BCH_DMA_ALIGNMENT - 1)) ||
+ !virt_addr_valid(buf)) { /* vmalloc'd buffer! */
+ bounce = true;
+ }
+
+ if (bounce) {
+ memcpy(nandi->page_buf, buf, page_size);
+ p = nandi->page_buf;
+ nandi->cached_page = -1;
+ }
+
+ emiss_nandi_select(nandi, STM_NANDI_BCH);
+
+ nandi_enable_interrupts(nandi, NANDBCH_INT_SEQNODESOVER);
+ reinit_completion(&nandi->seq_completed);
+
+ prog->addr = (uint32_t)((offs >> (chip->page_shift - 8)) & 0xffffff00);
+
+ buf_phys = dma_map_single(NULL, p, page_size, DMA_TO_DEVICE);
+ memset(nandi->buf_list, 0x00, NANDI_BCH_BUF_LIST_SIZE);
+ nandi->buf_list[0] = buf_phys | (nandi->sectors_per_page - 1);
+
+ list_phys = dma_map_single(NULL, nandi->buf_list,
+ NANDI_BCH_BUF_LIST_SIZE, DMA_TO_DEVICE);
+
+ writel(list_phys, nandi->base + NANDBCH_BUFFER_LIST_PTR);
+
+ bch_load_prog_cpu(nandi, prog);
+
+ bch_wait_seq(nandi);
+
+ nandi_disable_interrupts(nandi, NANDBCH_INT_SEQNODESOVER);
+
+ dma_unmap_single(NULL, list_phys, NANDI_BCH_BUF_LIST_SIZE,
+ DMA_TO_DEVICE);
+ dma_unmap_single(NULL, buf_phys, page_size, DMA_FROM_DEVICE);
+
+ status = (uint8_t)(readl(nandi->base +
+ NANDBCH_CHECK_STATUS_REG_A) & 0xff);
+
+ return status;
+}
+EXPORT_SYMBOL(bch_write_page);
+
+static int bch_write(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, int data_len, const uint8_t *buf,
+ int oob_required, int page, int cached, int raw)
+{
+ struct nandi_controller *nandi = chip->priv;
+ uint32_t page_size = mtd->writesize;
+ loff_t offs = (loff_t)page * page_size;
+ int ret;
+
+ ret = bch_write_page(nandi, offs, buf);
+ if (ret & NAND_STATUS_FAIL)
+ return -EIO;
+
+ return 0;
+}
+
+/*
+ * Hamming-FLEX operations
+ */
+static int flex_wait_rbn(struct nandi_controller *nandi)
+{
+ int ret;
+
+ ret = wait_for_completion_timeout(&nandi->rbn_completed, HZ/2);
+ if (!ret)
+ dev_err(nandi->dev, "FLEX RBn timeout\n");
+
+ return ret;
+}
+
+static void flex_cmd(struct nandi_controller *nandi, uint8_t cmd)
+{
+ uint32_t val;
+
+ val = (FLEX_CMD_CSN | FLEX_CMD_BEATS_1 | cmd);
+ writel(val, nandi->base + NANDHAM_FLEX_CMD);
+}
+
+static void flex_addr(struct nandi_controller *nandi,
+ uint32_t addr, int cycles)
+{
+ addr &= 0x00ffffff;
+
+ BUG_ON(cycles < 1);
+ BUG_ON(cycles > 3);
+
+ addr |= (FLEX_ADDR_CSN | FLEX_ADDR_ADD8_VALID);
+ addr |= (cycles & 0x3) << 28;
+
+ writel(addr, nandi->base + NANDHAM_FLEX_ADD);
+}
+
+/*
+ * Partial implementation of MTD/NAND Interface, based on Hamming-FLEX
+ * operation.
+ *
+ * Allows us to make use of nand_base.c functions where possible
+ * (e.g. nand_scan_ident() and friends).
+ */
+static void flex_command_lp(struct mtd_info *mtd, unsigned int command,
+ int column, int page)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nandi_controller *nandi = chip->priv;
+
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+
+ switch (command) {
+ case NAND_CMD_READOOB:
+ /* Emulate NAND_CMD_READOOB */
+ column += mtd->writesize;
+ command = NAND_CMD_READ0;
+ break;
+ case NAND_CMD_READ0:
+ case NAND_CMD_ERASE1:
+ case NAND_CMD_SEQIN:
+ case NAND_CMD_RESET:
+ case NAND_CMD_PARAM:
+ /* Prime RBn wait */
+ nandi_enable_interrupts(nandi, NAND_INT_RBN);
+ reinit_completion(&nandi->rbn_completed);
+ break;
+ case NAND_CMD_READID:
+ case NAND_CMD_STATUS:
+ case NAND_CMD_ERASE2:
+ break;
+ default:
+ /* Catch unexpected commands */
+ BUG();
+ }
+
+ /*
+ * Command Cycle
+ */
+ flex_cmd(nandi, command);
+
+ /*
+ * Address Cycles
+ */
+ if (column != -1)
+ flex_addr(nandi, column,
+ (command == NAND_CMD_READID) ? 1 : 2);
+
+ if (page != -1)
+ flex_addr(nandi, page, nandi->extra_addr ? 3 : 2);
+
+ /* Complete 'READ0' command */
+ if (command == NAND_CMD_READ0)
+ flex_cmd(nandi, NAND_CMD_READSTART);
+
+ /* Wait for RBn, if required */
+ /* (Note, other commands may handle wait elsewhere) */
+ if (command == NAND_CMD_RESET ||
+ command == NAND_CMD_READ0 ||
+ command == NAND_CMD_PARAM) {
+ flex_wait_rbn(nandi);
+ nandi_disable_interrupts(nandi, NAND_INT_RBN);
+ }
+}
+
+static uint8_t flex_read_byte(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nandi_controller *nandi = chip->priv;
+
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+
+ return (uint8_t)(readl(nandi->base + NANDHAM_FLEX_DATA) & 0xff);
+}
+
+static int flex_wait_func(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct nandi_controller *nandi = chip->priv;
+
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+
+ flex_wait_rbn(nandi);
+
+ flex_cmd(nandi, NAND_CMD_STATUS);
+
+ return (int)(readl(nandi->base + NANDHAM_FLEX_DATA) & 0xff);
+}
+
+/* Multi-CS devices not supported */
+static void flex_select_chip(struct mtd_info *mtd, int chipnr)
+{
+
+}
+
+static void flex_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nandi_controller *nandi = chip->priv;
+ int aligned;
+
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+
+ /* Read bytes until buf is 4-byte aligned */
+ while (len && ((unsigned int)buf & 0x3)) {
+ *buf++ = (uint8_t)(readl(nandi->base + NANDHAM_FLEX_DATA)
+ & 0xff);
+ len--;
+ };
+
+ /* Use 'BEATS_4'/readsl */
+ if (len > 8) {
+ aligned = len & ~0x3;
+ writel(FLEX_DATA_CFG_BEATS_4 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAREAD_CONFIG);
+
+ readsl(nandi->base + NANDHAM_FLEX_DATA, buf, aligned >> 2);
+
+ buf += aligned;
+ len -= aligned;
+
+ writel(FLEX_DATA_CFG_BEATS_1 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAREAD_CONFIG);
+ }
+
+ /* Mop up remaining bytes */
+ while (len > 0) {
+ *buf++ = (uint8_t)(readl(nandi->base + NANDHAM_FLEX_DATA)
+ & 0xff);
+ len--;
+ }
+}
+
+static void flex_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nandi_controller *nandi = chip->priv;
+ int aligned;
+
+ /* Write bytes until buf is 4-byte aligned */
+ while (len && ((unsigned int)buf & 0x3)) {
+ writel(*buf++, nandi->base + NANDHAM_FLEX_DATA);
+ len--;
+ };
+
+ /* USE 'BEATS_4/writesl */
+ if (len > 8) {
+ aligned = len & ~0x3;
+ writel(FLEX_DATA_CFG_BEATS_4 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAWRITE_CONFIG);
+ writesl(nandi->base + NANDHAM_FLEX_DATA, buf, aligned >> 2);
+ buf += aligned;
+ len -= aligned;
+ writel(FLEX_DATA_CFG_BEATS_1 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAWRITE_CONFIG);
+ }
+
+ /* Mop up remaining bytes */
+ while (len > 0) {
+ writel(*buf++, nandi->base + NANDHAM_FLEX_DATA);
+ len--;
+ }
+}
+
+int flex_read_raw(struct nandi_controller *nandi,
+ uint32_t page_addr,
+ uint32_t col_addr,
+ uint8_t *buf, uint32_t len)
+{
+ dev_dbg(nandi->dev, "%s %u bytes at [0x%06x,0x%04x]\n",
+ __func__, len, page_addr, col_addr);
+
+ BUG_ON(len & 0x3);
+ BUG_ON((unsigned long)buf & 0x3);
+
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+ nandi_enable_interrupts(nandi, NAND_INT_RBN);
+ reinit_completion(&nandi->rbn_completed);
+
+ writel(FLEX_DATA_CFG_BEATS_4 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAREAD_CONFIG);
+
+ flex_cmd(nandi, NAND_CMD_READ0);
+ flex_addr(nandi, col_addr, 2);
+ flex_addr(nandi, page_addr, nandi->extra_addr ? 3 : 2);
+ flex_cmd(nandi, NAND_CMD_READSTART);
+
+ flex_wait_rbn(nandi);
+
+ readsl(nandi->base + NANDHAM_FLEX_DATA, buf, len / 4);
+
+ nandi_disable_interrupts(nandi, NAND_INT_RBN);
+
+ writel(FLEX_DATA_CFG_BEATS_1 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAREAD_CONFIG);
+
+ return 0;
+}
+EXPORT_SYMBOL(flex_read_raw);
+
+static int bch_mtd_read_oob(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ BUG();
+ return 0;
+}
+
+static int bch_mtd_write_oob(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ BUG();
+ return 0;
+}
+
+static int bch_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ BUG();
+ return 0;
+}
+
+static int bch_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
+{
+ BUG();
+ return 0;
+}
+
+static void bch_hwctl(struct mtd_info *mtd, int mode)
+{
+ BUG();
+}
+
+static int bch_calculate(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ BUG();
+ return 0;
+}
+
+static int bch_correct(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc,
+ uint8_t *calc_ecc)
+{
+ BUG();
+ return 0;
+}
+
+/*
+ * Initialisation
+ */
+static int bch_check_compatibility(struct nandi_controller *nandi,
+ struct mtd_info *mtd,
+ struct nand_chip *chip)
+{
+ if (chip->bits_per_cell > 1)
+ dev_warn(nandi->dev, "MLC NAND not fully supported\n");
+
+ if (chip->options & NAND_BUSWIDTH_16) {
+ dev_err(nandi->dev, "x16 NAND not supported\n");
+ return false;
+ }
+
+ if (nandi->blocks_per_device / 4 > mtd->writesize) {
+ /* Need to implement multi-page BBT support... */
+ dev_err(nandi->dev, "BBT too big to fit in single page\n");
+ return false;
+ }
+
+ if (bch_ecc_sizes[nandi->bch_ecc_mode] * nandi->sectors_per_page >
+ mtd->oobsize) {
+ dev_err(nandi->dev, "insufficient OOB for selected ECC\n");
+ return false;
+ }
+
+ return true;
+}
+
+/* Select strongest ECC scheme compatible with OOB size */
+static int bch_set_ecc_auto(struct nandi_controller *nandi,
+ struct mtd_info *mtd)
+{
+ int oob_bytes_per_sector = mtd->oobsize / nandi->sectors_per_page;
+ int try_ecc_modes[] = { BCH_30BIT_ECC, BCH_18BIT_ECC, -1 };
+ int m, ecc_mode;
+
+ for (m = 0; try_ecc_modes[m] >= 0; m++) {
+ ecc_mode = try_ecc_modes[m];
+ if (oob_bytes_per_sector >= bch_ecc_sizes[ecc_mode]) {
+ nandi->bch_ecc_mode = ecc_mode;
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static void nandi_set_mtd_defaults(struct nandi_controller *nandi,
+ struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct nandi_info *info = &nandi->info;
+ int i;
+
+ /* ecclayout */
+ info->ecclayout.eccbytes = mtd->oobsize;
+ for (i = 0; i < 64; i++)
+ info->ecclayout.eccpos[i] = i;
+ info->ecclayout.oobfree[0].offset = 0;
+ info->ecclayout.oobfree[0].length = 0;
+ chip->ecc.mode = NAND_ECC_HW;
+
+ /* nand_chip */
+ chip->controller = &chip->hwcontrol;
+ spin_lock_init(&chip->controller->lock);
+ init_waitqueue_head(&chip->controller->wq);
+ chip->state = FL_READY;
+ chip->priv = nandi;
+ chip->ecc.layout = &info->ecclayout;
+ chip->options |= NAND_NO_SUBPAGE_WRITE;
+
+ chip->cmdfunc = flex_command_lp;
+ chip->read_byte = flex_read_byte;
+ chip->select_chip = flex_select_chip;
+ chip->waitfunc = flex_wait_func;
+ chip->read_buf = flex_read_buf;
+ chip->write_buf = flex_write_buf;
+
+ chip->bbt_options |= NAND_BBT_USE_FLASH;
+
+ /* mtd_info */
+ mtd->owner = THIS_MODULE;
+ mtd->type = MTD_NANDFLASH;
+ mtd->flags = MTD_CAP_NANDFLASH;
+ mtd->ecclayout = &info->ecclayout;
+
+ chip->ecc.hwctl = bch_hwctl;
+ chip->ecc.calculate = bch_calculate;
+ chip->ecc.correct = bch_correct;
+
+ chip->ecc.read_oob = bch_mtd_read_oob;
+ chip->ecc.write_oob = bch_mtd_write_oob;
+
+ chip->ecc.read_page = bch_read;
+ chip->ecc.read_page_raw = bch_read_page_raw;
+ chip->ecc.write_page_raw = bch_write_page_raw;
+ chip->write_page = bch_write;
+ chip->erase = bch_erase;
+
+#ifdef CONFIG_MTD_NAND_STM_BCH_BBT
+ chip->scan_bbt = bch_scan_bbt;
+ chip->block_bad = bch_block_isbad;
+ chip->block_markbad = bch_block_markbad;
+#endif
+}
+
+/*
+ * Timing and Clocks
+ */
+
+static void nandi_clk_enable(struct nandi_controller *nandi)
+{
+ clk_prepare_enable(nandi->emi_clk);
+ clk_prepare_enable(nandi->bch_clk);
+}
+
+static void nandi_clk_disable(struct nandi_controller *nandi)
+{
+ clk_disable_unprepare(nandi->emi_clk);
+ clk_disable_unprepare(nandi->bch_clk);
+}
+
+static struct clk *nandi_clk_setup(struct nandi_controller *nandi,
+ char *clkname)
+{
+ struct clk *clk;
+ int ret;
+
+ clk = devm_clk_get(nandi->dev, clkname);
+ if (IS_ERR_OR_NULL(clk)) {
+ dev_warn(nandi->dev, "Failed to get %s clock\n", clkname);
+ return NULL;
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_warn(nandi->dev, "Failed to enable %s clock\n", clkname);
+ return NULL;
+ }
+
+ return clk;
+}
+
+/* Derive Hamming-FLEX timing register values from 'nand_sdr_timings' data */
+static void flex_calc_timing_registers(const struct nand_sdr_timings *spec,
+ int tCLK, int relax,
+ uint32_t *ctl_timing,
+ uint32_t *wen_timing,
+ uint32_t *ren_timing)
+{
+ int tMAX_HOLD;
+ int n_ctl_setup;
+ int n_ctl_hold;
+ int n_ctl_wb;
+
+ int tMAX_WEN_OFF;
+ int n_wen_on;
+ int n_wen_off;
+
+ int tMAX_REN_OFF;
+ int n_ren_on;
+ int n_ren_off;
+
+ /*
+ * CTL_TIMING
+ */
+
+ /* - SETUP */
+ n_ctl_setup = (PICO_TO_MILI(spec->tCLS_min - spec->tWP_min)
+ + tCLK - 1)/tCLK;
+ if (n_ctl_setup < 1)
+ n_ctl_setup = 1;
+ n_ctl_setup += relax;
+
+ /* - HOLD */
+ tMAX_HOLD = spec->tCLH_min;
+ if (spec->tCH_min > tMAX_HOLD)
+ tMAX_HOLD = spec->tCH_min;
+ if (spec->tALH_min > tMAX_HOLD)
+ tMAX_HOLD = spec->tALH_min;
+ if (spec->tDH_min > tMAX_HOLD)
+ tMAX_HOLD = spec->tDH_min;
+ n_ctl_hold = (PICO_TO_MILI(tMAX_HOLD) + tCLK - 1)/tCLK + relax;
+
+ /* - CE_deassert_hold = 0 */
+
+ /* - WE_high_to_RBn_low */
+ n_ctl_wb = (PICO_TO_MILI(spec->tWB_max) + tCLK - 1)/tCLK;
+
+ *ctl_timing = ((n_ctl_setup & 0xff) |
+ (n_ctl_hold & 0xff) << 8 |
+ (n_ctl_wb & 0xff) << 24);
+
+ /*
+ * WEN_TIMING
+ */
+
+ /* - ON */
+ n_wen_on = (PICO_TO_MILI(spec->tWH_min) + tCLK - 1)/tCLK + relax;
+
+ /* - OFF */
+ tMAX_WEN_OFF = spec->tWC_min - spec->tWH_min;
+ if (spec->tWP_min > tMAX_WEN_OFF)
+ tMAX_WEN_OFF = spec->tWP_min;
+ n_wen_off = (PICO_TO_MILI(tMAX_WEN_OFF) + tCLK - 1)/tCLK + relax;
+
+ *wen_timing = ((n_wen_on & 0xff) |
+ (n_wen_off & 0xff) << 8);
+
+ /*
+ * REN_TIMING
+ */
+
+ /* - ON */
+ n_ren_on = (PICO_TO_MILI(spec->tREH_min) + tCLK - 1)/tCLK + relax;
+
+ /* - OFF */
+ tMAX_REN_OFF = spec->tRC_min - spec->tREH_min;
+ if (spec->tRP_min > tMAX_REN_OFF)
+ tMAX_REN_OFF = spec->tRP_min;
+ if (spec->tREA_max > tMAX_REN_OFF)
+ tMAX_REN_OFF = spec->tREA_max;
+ n_ren_off = (PICO_TO_MILI(tMAX_REN_OFF) + tCLK - 1)/tCLK + 1 + relax;
+
+ *ren_timing = ((n_ren_on & 0xff) |
+ (n_ren_off & 0xff) << 8);
+}
+
+/* Derive BCH timing register values from 'nand_sdr_timings' data */
+static void bch_calc_timing_registers(const struct nand_sdr_timings *spec,
+ int tCLK, int relax,
+ uint32_t *ctl_timing,
+ uint32_t *wen_timing,
+ uint32_t *ren_timing)
+{
+ int tMAX_HOLD;
+ int n_ctl_setup;
+ int n_ctl_hold;
+ int n_ctl_wb;
+
+ int n_wen_on;
+ int n_wen_off;
+ int wen_half_on;
+ int wen_half_off;
+
+ int tMAX_REN_ON;
+ int tMAX_CS_DEASSERT;
+ int n_d_latch;
+ int n_telqv;
+ int n_ren_on;
+ int n_ren_off;
+
+ /*
+ * CTL_TIMING
+ */
+
+ /* - SETUP */
+ if (spec->tCLS_min > spec->tWP_min)
+ n_ctl_setup = (PICO_TO_MILI(spec->tCLS_min - spec->tWP_min)
+ + tCLK - 1)/tCLK;
+ else
+ n_ctl_setup = 0;
+ n_ctl_setup += relax;
+
+ /* - HOLD */
+ tMAX_HOLD = spec->tCLH_min;
+ if (spec->tCH_min > tMAX_HOLD)
+ tMAX_HOLD = spec->tCH_min;
+ if (spec->tALH_min > tMAX_HOLD)
+ tMAX_HOLD = spec->tALH_min;
+ if (spec->tDH_min > tMAX_HOLD)
+ tMAX_HOLD = spec->tDH_min;
+ n_ctl_hold = (PICO_TO_MILI(tMAX_HOLD) + tCLK - 1)/tCLK + relax;
+ /* - CE_deassert_hold = 0 */
+
+ /* - WE_high_to_RBn_low */
+ n_ctl_wb = (PICO_TO_MILI(spec->tWB_max) + tCLK - 1)/tCLK;
+
+ *ctl_timing = ((n_ctl_setup & 0xff) |
+ (n_ctl_hold & 0xff) << 8 |
+ (n_ctl_wb & 0xff) << 24);
+
+ /*
+ * WEN_TIMING
+ */
+
+ /* - ON */
+ n_wen_on = (2 * PICO_TO_MILI(spec->tWH_min) + tCLK - 1)/tCLK;
+ wen_half_on = n_wen_on % 2;
+ n_wen_on /= 2;
+ n_wen_on += relax;
+
+ /* - OFF */
+ n_wen_off = (2 * PICO_TO_MILI(spec->tWP_min) + tCLK - 1)/tCLK;
+ wen_half_off = n_wen_off % 2;
+ n_wen_off /= 2;
+ n_wen_off += relax;
+
+ *wen_timing = ((n_wen_on & 0xff) |
+ (n_wen_off & 0xff) << 8 |
+ (wen_half_on << 16) |
+ (wen_half_off << 17));
+
+ /*
+ * REN_TIMING
+ */
+
+ /* - ON */
+ tMAX_REN_ON = spec->tRC_min - spec->tRP_min;
+ if (spec->tREH_min > tMAX_REN_ON)
+ tMAX_REN_ON = spec->tREH_min;
+
+ n_ren_on = (2 * PICO_TO_MILI(tMAX_REN_ON) + tCLK - 1)/tCLK;
+ n_ren_on /= 2;
+ n_ren_on += relax;
+
+ /* - OFF */
+ n_ren_off = (2 * PICO_TO_MILI(spec->tREA_max) + tCLK - 1)/tCLK;
+ n_ren_off /= 2;
+ n_ren_off += relax;
+
+ /* - DATA_LATCH */
+ if (PICO_TO_MILI(spec->tREA_max) <=
+ (PICO_TO_MILI(spec->tRP_min) - (2 * tCLK)))
+ n_d_latch = 0;
+ else if (PICO_TO_MILI(spec->tREA_max) <=
+ (PICO_TO_MILI(spec->tRP_min) - tCLK))
+ n_d_latch = 1;
+ else if ((spec->tREA_max <= spec->tRP_min) &&
+ (PICO_TO_MILI(spec->tRHOH_min) >= 2 * tCLK))
+ n_d_latch = 2;
+ else
+ n_d_latch = 3;
+
+ /* - TELQV */
+ tMAX_CS_DEASSERT = spec->tCOH_min;
+ if (spec->tCHZ_max > tMAX_CS_DEASSERT)
+ tMAX_CS_DEASSERT = spec->tCHZ_max;
+
+ n_telqv = (PICO_TO_MILI(tMAX_CS_DEASSERT) + tCLK - 1)/tCLK;
+
+ *ren_timing = ((n_ren_on & 0xff) |
+ (n_ren_off & 0xff) << 8 |
+ (n_d_latch & 0x3) << 16 |
+ (wen_half_on << 18) |
+ (wen_half_off << 19) |
+ (n_telqv & 0xff) << 24);
+}
+
+static void flex_configure_timing_registers(struct nandi_controller *nandi,
+ const struct nand_sdr_timings *spec,
+ int relax)
+{
+ uint32_t ctl_timing;
+ uint32_t wen_timing;
+ uint32_t ren_timing;
+ int emi_t_ns;
+
+ /* Select Hamming Controller */
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+
+ /* Get EMI clock (default 100MHz) */
+ if (nandi->emi_clk)
+ emi_t_ns = 1000000000UL / clk_get_rate(nandi->emi_clk);
+ else {
+ dev_warn(nandi->dev,
+ "No EMI clock available; assuming default 100MHz\n");
+ emi_t_ns = 10;
+ }
+
+ /* Derive timing register values from specification */
+ flex_calc_timing_registers(spec, emi_t_ns, relax,
+ &ctl_timing, &wen_timing, &ren_timing);
+
+ dev_dbg(nandi->dev,
+ "updating FLEX timing configuration [0x%08x, 0x%08x, 0x%08x]\n",
+ ctl_timing, wen_timing, ren_timing);
+
+ /* Program timing registers */
+ writel(ctl_timing, nandi->base + NANDHAM_CTL_TIMING);
+ writel(wen_timing, nandi->base + NANDHAM_WEN_TIMING);
+ writel(ren_timing, nandi->base + NANDHAM_REN_TIMING);
+}
+
+static void bch_configure_timing_registers(struct nandi_controller *nandi,
+ const struct nand_sdr_timings *spec,
+ int relax)
+{
+ uint32_t ctl_timing;
+ uint32_t wen_timing;
+ uint32_t ren_timing;
+ int bch_t_ns;
+
+ /* Select BCH Controller */
+ emiss_nandi_select(nandi, STM_NANDI_BCH);
+
+ /* Get BCH clock (default 200MHz) */
+ if (nandi->bch_clk)
+ bch_t_ns = 1000000000UL / clk_get_rate(nandi->bch_clk);
+ else {
+ dev_warn(nandi->dev,
+ "No BCH clock available; assuming default 200MHz\n");
+ bch_t_ns = 5;
+ }
+
+ /* Derive timing register values from specification */
+ bch_calc_timing_registers(spec, bch_t_ns, relax,
+ &ctl_timing, &wen_timing, &ren_timing);
+
+ dev_dbg(nandi->dev,
+ "updating BCH timing configuration [0x%08x, 0x%08x, 0x%08x]\n",
+ ctl_timing, wen_timing, ren_timing);
+
+ /* Program timing registers */
+ writel(ctl_timing, nandi->base + NANDBCH_CTL_TIMING);
+ writel(wen_timing, nandi->base + NANDBCH_WEN_TIMING);
+ writel(ren_timing, nandi->base + NANDBCH_REN_TIMING);
+}
+
+static void nandi_configure_timing_registers(struct nandi_controller *nandi,
+ const struct nand_sdr_timings *spec,
+ int relax)
+{
+ bch_configure_timing_registers(nandi, spec, relax);
+ flex_configure_timing_registers(nandi, spec, relax);
+}
+
+static void nandi_init_hamming(struct nandi_controller *nandi, int emi_bank)
+{
+ dev_dbg(nandi->dev, "%s\n", __func__);
+
+ emiss_nandi_select(nandi, STM_NANDI_HAMMING);
+
+ /* Reset and disable boot-mode controller */
+ writel(BOOT_CFG_RESET, nandi->base + NANDHAM_BOOTBANK_CFG);
+ udelay(1);
+ writel(0x00000000, nandi->base + NANDHAM_BOOTBANK_CFG);
+
+ /* Reset controller */
+ writel(CFG_RESET, nandi->base + NANDHAM_FLEXMODE_CFG);
+ udelay(1);
+ writel(0x00000000, nandi->base + NANDHAM_FLEXMODE_CFG);
+
+ /* Set EMI Bank */
+ writel(0x1 << emi_bank, nandi->base + NANDHAM_FLEX_MUXCTRL);
+
+ /* Enable FLEX mode */
+ writel(CFG_ENABLE_FLEX, nandi->base + NANDHAM_FLEXMODE_CFG);
+
+ /* Configure FLEX_DATA_READ/WRITE for 1-byte access */
+ writel(FLEX_DATA_CFG_BEATS_1 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAREAD_CONFIG);
+ writel(FLEX_DATA_CFG_BEATS_1 | FLEX_DATA_CFG_CSN,
+ nandi->base + NANDHAM_FLEX_DATAREAD_CONFIG);
+
+ /* RBn interrupt on rising edge */
+ writel(NAND_EDGE_CFG_RBN_RISING, nandi->base + NANDHAM_INT_EDGE_CFG);
+
+ /* Enable interrupts */
+ nandi_enable_interrupts(nandi, NAND_INT_ENABLE);
+}
+
+static void nandi_init_bch(struct nandi_controller *nandi, int emi_bank)
+{
+ dev_dbg(nandi->dev, "%s\n", __func__);
+
+ /* Initialise BCH Controller */
+ emiss_nandi_select(nandi, STM_NANDI_BCH);
+
+ /* Reset and disable boot-mode controller */
+ writel(BOOT_CFG_RESET, nandi->base + NANDBCH_BOOTBANK_CFG);
+ udelay(1);
+ writel(0x00000000, nandi->base + NANDBCH_BOOTBANK_CFG);
+
+ /* Reset AFM controller */
+ writel(CFG_RESET, nandi->base + NANDBCH_CONTROLLER_CFG);
+ udelay(1);
+ writel(0x00000000, nandi->base + NANDBCH_CONTROLLER_CFG);
+
+ /* Set EMI Bank */
+ writel(0x1 << emi_bank, nandi->base + NANDBCH_FLEX_MUXCTRL);
+
+ /* Reset ECC stats */
+ writel(CFG_RESET_ECC_ALL, nandi->base + NANDBCH_CONTROLLER_CFG);
+ udelay(1);
+
+ /* Enable AFM */
+ writel(CFG_ENABLE_AFM, nandi->base + NANDBCH_CONTROLLER_CFG);
+
+ /* Configure Read DMA Plugs (values supplied by Validation) */
+ writel(0x00000005, nandi->dma + EMISS_NAND_RD_DMA_PAGE_SIZE);
+ writel(0x00000005, nandi->dma + EMISS_NAND_RD_DMA_MAX_OPCODE_SIZE);
+ writel(0x00000002, nandi->dma + EMISS_NAND_RD_DMA_MIN_OPCODE_SIZE);
+ writel(0x00000001, nandi->dma + EMISS_NAND_RD_DMA_MAX_CHUNK_SIZE);
+ writel(0x00000000, nandi->dma + EMISS_NAND_RD_DMA_MAX_MESSAGE_SIZE);
+
+ /* Configure Write DMA Plugs (values supplied by Validation) */
+ writel(0x00000005, nandi->dma + EMISS_NAND_WR_DMA_PAGE_SIZE);
+ writel(0x00000005, nandi->dma + EMISS_NAND_WR_DMA_MAX_OPCODE_SIZE);
+ writel(0x00000002, nandi->dma + EMISS_NAND_WR_DMA_MIN_OPCODE_SIZE);
+ writel(0x00000001, nandi->dma + EMISS_NAND_WR_DMA_MAX_CHUNK_SIZE);
+ writel(0x00000000, nandi->dma + EMISS_NAND_WR_DMA_MAX_MESSAGE_SIZE);
+
+ nandi_enable_interrupts(nandi, NAND_INT_ENABLE);
+}
+
+static void nandi_init_controller(struct nandi_controller *nandi,
+ int emi_bank)
+{
+ nandi_init_bch(nandi, emi_bank);
+ nandi_init_hamming(nandi, emi_bank);
+}
+
+/* Initialise working buffers, accomodating DMA alignment constraints */
+static int nandi_init_working_buffers(struct nandi_controller *nandi,
+ struct nandi_bbt_info *bbt_info,
+ struct mtd_info *mtd)
+{
+ uint32_t bbt_buf_size;
+ uint32_t buf_size;
+
+ /* - Page and OOB */
+ buf_size = mtd->writesize + mtd->oobsize + NANDI_BCH_DMA_ALIGNMENT;
+
+ /* - BBT data (page-size aligned) */
+ bbt_info->bbt_size = nandi->blocks_per_device >> 2; /* 2 bits/block */
+ bbt_buf_size = ALIGN(bbt_info->bbt_size, mtd->writesize);
+ buf_size += bbt_buf_size + NANDI_BCH_DMA_ALIGNMENT;
+
+ /* - BCH BUF list */
+ buf_size += NANDI_BCH_BUF_LIST_SIZE + NANDI_BCH_DMA_ALIGNMENT;
+
+ /* Allocate bufffer */
+ nandi->buf = devm_kzalloc(nandi->dev, buf_size, GFP_KERNEL);
+ if (!nandi->buf) {
+ dev_err(nandi->dev, "failed to allocate working buffers\n");
+ return -ENOMEM;
+ }
+
+ /* Set/Align buffer pointers */
+ nandi->page_buf = PTR_ALIGN(nandi->buf, NANDI_BCH_DMA_ALIGNMENT);
+ nandi->oob_buf = nandi->page_buf + mtd->writesize;
+ bbt_info->bbt = PTR_ALIGN(nandi->oob_buf + mtd->oobsize,
+ NANDI_BCH_DMA_ALIGNMENT);
+ nandi->buf_list = (uint32_t *)PTR_ALIGN(bbt_info->bbt + bbt_buf_size,
+ NANDI_BCH_DMA_ALIGNMENT);
+ nandi->cached_page = -1;
+
+ return 0;
+}
+
+static int remap_named_resource(struct platform_device *pdev,
+ char *name,
+ void __iomem **io_ptr)
+{
+ struct resource *res, *mem;
+ resource_size_t size;
+ void __iomem *p;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, name);
+ if (!res)
+ return -ENXIO;
+
+ size = resource_size(res);
+
+ mem = devm_request_mem_region(&pdev->dev, res->start, size, name);
+ if (!mem)
+ return -EBUSY;
+
+ p = devm_ioremap_nocache(&pdev->dev, res->start, size);
+ if (!p)
+ return -ENOMEM;
+
+ *io_ptr = p;
+
+ return 0;
+}
+
+static struct nandi_controller *
+nandi_init_resources(struct platform_device *pdev)
+{
+ struct stm_nand_bch_ddata *ddata = platform_get_drvdata(pdev);
+ struct nandi_controller *nandi;
+ int irq;
+ int err;
+
+ nandi = devm_kzalloc(&pdev->dev, sizeof(*nandi), GFP_KERNEL);
+ if (!nandi) {
+ dev_err(&pdev->dev,
+ "failed to allocate NANDi controller data\n");
+ return ERR_PTR(-ENOMEM);
+ }
+
+ nandi->dev = &pdev->dev;
+
+ err = remap_named_resource(pdev, "emi_nand", &nandi->base);
+ if (err)
+ return ERR_PTR(err);
+
+ err = remap_named_resource(pdev, "emiss", &nandi->emiss);
+ if (err)
+ return ERR_PTR(err);
+
+ nandi->dma = nandi->emiss + EMISS_NAND_DMA;
+ nandi->emisscfg = nandi->emiss + EMISS_CFG;
+
+ irq = platform_get_irq_byname(pdev, "nand_irq");
+ if (irq < 0) {
+ dev_err(&pdev->dev, "failed to find IRQ resource\n");
+ return ERR_PTR(irq);
+ }
+
+ err = devm_request_irq(&pdev->dev, irq, nandi_irq_handler,
+ IRQF_DISABLED, dev_name(&pdev->dev), nandi);
+ if (err) {
+ dev_err(&pdev->dev, "irq request failed\n");
+ return ERR_PTR(err);
+ }
+
+ nandi->emi_clk = nandi_clk_setup(nandi, "emi");
+ nandi->bch_clk = nandi_clk_setup(nandi, "bch");
+
+ ddata->nandi = nandi;
+
+ return nandi;
+}
+
+static void *stm_bch_dt_get_ddata(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct stm_nand_bch_ddata *ddata;
+ int ecc_strength;
+ int ret;
+
+ ddata = devm_kzalloc(&pdev->dev, sizeof(*ddata), GFP_KERNEL);
+ if (!ddata)
+ return ERR_PTR(-ENOMEM);
+
+ of_property_read_u32(np, "nand-ecc-strength", &ecc_strength);
+ if (ecc_strength == 0)
+ ddata->bch_ecc_cfg = BCH_NO_ECC;
+ else if (ecc_strength == 18)
+ ddata->bch_ecc_cfg = BCH_18BIT_ECC;
+ else if (ecc_strength == 30)
+ ddata->bch_ecc_cfg = BCH_30BIT_ECC;
+ else
+ ddata->bch_ecc_cfg = BCH_ECC_AUTO;
+
+ ret = stm_of_get_nand_banks(&pdev->dev, np, &ddata->bank);
+ if (ret < 0)
+ return ERR_PTR(ret);
+
+ return ddata;
+}
+
+static int stm_nand_bch_probe(struct platform_device *pdev)
+{
+ const char *part_probes[] = { "cmdlinepart", "ofpart", NULL, };
+ struct device_node *np = pdev->dev.of_node;
+ struct mtd_part_parser_data ppdata;
+ struct stm_nand_bch_ddata *ddata;
+ struct stm_nand_bank_data *bank;
+ struct nandi_bbt_info *bbt_info;
+ struct nandi_controller *nandi;
+ struct nandi_info *info;
+ struct nand_chip *chip;
+ struct mtd_info *mtd;
+ int compatible, err;
+
+ if (!np) {
+ dev_err(&pdev->dev, "DT node found\n");
+ return -EINVAL;
+ }
+
+ ddata = stm_bch_dt_get_ddata(pdev);
+ if (IS_ERR(ddata))
+ return PTR_ERR(ddata);
+
+ ppdata.of_node = stm_of_get_partitions_node(np, 0);
+
+ platform_set_drvdata(pdev, ddata);
+
+ nandi = nandi_init_resources(pdev);
+ if (IS_ERR(nandi)) {
+ dev_err(&pdev->dev, "failed to initialise NANDi resources\n");
+ return PTR_ERR(nandi);
+ }
+
+ init_completion(&nandi->seq_completed);
+ init_completion(&nandi->rbn_completed);
+
+ bank = ddata->bank;
+ if (bank)
+ nandi_init_controller(nandi, bank->csn);
+
+ info = &nandi->info;
+ chip = &info->chip;
+ bbt_info = &info->bbt_info;
+ mtd = &info->mtd;
+ mtd->priv = chip;
+ mtd->name = dev_name(&pdev->dev);
+ mtd->dev.parent = &pdev->dev;
+
+ nandi_set_mtd_defaults(nandi, mtd, chip);
+
+ err = nand_scan_ident(mtd, 1, NULL);
+ if (err)
+ return err;
+
+ /*
+ * Configure timing registers
+ */
+ if (bank && bank->timing_spec) {
+ dev_info(&pdev->dev, "Using platform timing data\n");
+ nandi_configure_timing_registers(nandi, bank->timing_spec,
+ bank->timing_relax);
+ } else if (chip->onfi_version) {
+ int mode = fls(onfi_get_async_timing_mode(chip) - 1);
+ const struct nand_sdr_timings *spec =
+ onfi_async_timing_mode_to_sdr_timings(mode);
+
+ /* Modes 4 and 5 (EDO) are not supported on our H/W */
+ if (mode > 3)
+ mode = 3;
+
+ dev_info(&pdev->dev, "Using ONFI Timing Mode %d\n", mode);
+ nandi_configure_timing_registers(nandi, spec,
+ bank ? bank->timing_relax : 0);
+ } else {
+ dev_warn(&pdev->dev, "No timing data available\n");
+ }
+
+ if (mtd->writesize < NANDI_BCH_SECTOR_SIZE) {
+ dev_err(nandi->dev,
+ "page size incompatible with BCH ECC sector\n");
+ return -EINVAL;
+ }
+
+ /* Derive some working variables */
+ nandi->sectors_per_page = mtd->writesize / NANDI_BCH_SECTOR_SIZE;
+ nandi->blocks_per_device = mtd->size >> chip->phys_erase_shift;
+ nandi->extra_addr = ((chip->chipsize >> chip->page_shift) >
+ 0x10000) ? true : false;
+ mtd->writebufsize = mtd->writesize;
+
+ /* Set ECC mode */
+ if (ddata->bch_ecc_cfg == BCH_ECC_AUTO) {
+ err = bch_set_ecc_auto(nandi, mtd);
+ if (err) {
+ dev_err(nandi->dev, "insufficient OOB for BCH ECC\n");
+ return err;
+ }
+ } else {
+ nandi->bch_ecc_mode = ddata->bch_ecc_cfg;
+ }
+
+ chip->ecc.size = NANDI_BCH_SECTOR_SIZE;
+ chip->ecc.bytes = mtd->oobsize;
+ chip->ecc.strength = bch_ecc_strength[nandi->bch_ecc_mode];
+
+ info->ecclayout.eccbytes =
+ nandi->sectors_per_page * bch_ecc_sizes[nandi->bch_ecc_mode];
+
+ compatible = bch_check_compatibility(nandi, mtd, chip);
+ if (!compatible) {
+ dev_err(nandi->dev,
+ "NAND device incompatible with NANDi/BCH Controller\n");
+ return -EINVAL;
+ }
+
+ /* Tune BCH programs according to device found and ECC mode */
+ bch_configure_progs(nandi);
+
+ err = nandi_init_working_buffers(nandi, bbt_info, mtd);
+ if (err)
+ return err;
+
+ err = nand_scan_tail(mtd);
+ if (err)
+ return err;
+
+#ifdef CONFIG_MTD_NAND_STM_BCH_BBT
+ nandi_dump_bad_blocks(nandi);
+#endif
+ /* Add partitions */
+ return mtd_device_parse_register(mtd, part_probes, &ppdata,
+ bank->partitions, bank->nr_partitions);
+}
+
+static int stm_nand_bch_remove(struct platform_device *pdev)
+{
+ struct stm_nand_bch_ddata *ddata = platform_get_drvdata(pdev);
+ struct nandi_controller *nandi = ddata->nandi;
+
+ nand_release(&nandi->info.mtd);
+
+ nandi_clk_disable(nandi);
+
+ return 0;
+}
+
+static int stm_nand_bch_suspend(struct device *dev)
+{
+ struct stm_nand_bch_ddata *ddata = dev_get_drvdata(dev);
+ struct nandi_controller *nandi = ddata->nandi;
+
+ nandi_clk_disable(nandi);
+
+ return 0;
+}
+static int stm_nand_bch_resume(struct device *dev)
+{
+ struct stm_nand_bch_ddata *ddata = dev_get_drvdata(dev);
+ struct nandi_controller *nandi = ddata->nandi;
+
+ nandi_clk_enable(nandi);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(stm_nand_bch_pm_ops,
+ stm_nand_bch_suspend,
+ stm_nand_bch_resume);
+
+static struct of_device_id nand_bch_match[] = {
+ { .compatible = "st,nand-bch", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, nand_bch_match);
+
+static struct platform_driver stm_nand_bch_driver = {
+ .probe = stm_nand_bch_probe ,
+ .remove = stm_nand_bch_remove,
+ .driver = {
+ .name = "stm-nand-bch",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(nand_bch_match),
+ .pm = &stm_nand_bch_pm_ops,
+ },
+};
+module_platform_driver(stm_nand_bch_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Angus Clark");
+MODULE_DESCRIPTION("STM NAND BCH driver");
new file mode 100644
@@ -0,0 +1,109 @@
+/*
+ * drivers/mtd/nand/stm_nand_dt.c
+ *
+ * Support for NANDi BCH Controller Device Tree component
+ *
+ * Copyright (c) 2014 STMicroelectronics Limited
+ * Author: Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/byteorder/generic.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/stm_nand.h>
+
+#include "stm_nand_regs.h"
+
+/**
+* stm_of_get_partitions_node - get partitions node from stm-nand type devices.
+*
+* @dev device pointer to use for devm allocations.
+* @np device node of the driver.
+* @bank_nr which bank number to use to get partitions.
+*
+* Returns a node pointer if found, with refcount incremented, use
+* of_node_put() on it when done.
+*
+*/
+struct device_node *stm_of_get_partitions_node(struct device_node *np,
+ int bank_nr)
+{
+ struct device_node *banknp, *partsnp = NULL;
+ char name[10];
+
+ sprintf(name, "bank%d", bank_nr);
+ banknp = of_get_child_by_name(np, name);
+ if (banknp)
+ return NULL;
+
+ partsnp = of_get_child_by_name(banknp, "partitions");
+ of_node_put(banknp);
+
+ return partsnp;
+}
+EXPORT_SYMBOL(stm_of_get_partitions_node);
+
+/**
+ * stm_of_get_nand_banks - Get nand banks info from a given device node.
+ *
+ * @dev device pointer to use for devm allocations.
+ * @np device node of the driver.
+ * @banksptr double pointer to banks which is allocated
+ * and filled with bank data.
+ *
+ * Returns a count of banks found in the given device node.
+ *
+ */
+int stm_of_get_nand_banks(struct device *dev, struct device_node *np,
+ struct stm_nand_bank_data **banksptr)
+{
+ struct stm_nand_bank_data *banks;
+ struct device_node *banknp;
+ int nr_banks = 0;
+
+ if (!np)
+ return -ENODEV;
+
+ nr_banks = of_get_child_count(np);
+ if (!nr_banks) {
+ dev_err(dev, "No NAND banks specified in DT: %s\n",
+ np->full_name);
+ return -EINVAL;
+ }
+
+ *banksptr = devm_kzalloc(dev, sizeof(*banks) * nr_banks, GFP_KERNEL);
+ banks = *banksptr;
+ banknp = NULL;
+
+ for_each_child_of_node(np, banknp) {
+ int bank = 0;
+
+ of_property_read_u32(banknp, "st,nand-csn", &banks[bank].csn);
+
+ if (of_get_nand_bus_width(banknp) == 16)
+ banks[bank].options |= NAND_BUSWIDTH_16;
+ if (of_get_nand_on_flash_bbt(banknp))
+ banks[bank].bbt_options |= NAND_BBT_USE_FLASH;
+
+ banks[bank].nr_partitions = 0;
+ banks[bank].partitions = NULL;
+
+ of_property_read_u32(banknp, "st,nand-timing-relax",
+ &banks[bank].timing_relax);
+ bank++;
+ }
+
+ return nr_banks;
+}
+EXPORT_SYMBOL(stm_of_get_nand_banks);
new file mode 100644
@@ -0,0 +1,24 @@
+/*
+ * drivers/mtd/nand/stm_nand_dt.h
+ *
+ * Support for NANDi BCH Controller Device Tree component
+ *
+ * Copyright (c) 2014 STMicroelectronics Limited
+ * Author: Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef STM_NAND_DT_H
+#define STM_NAND_DT_H
+
+struct device_node *stm_of_get_partitions_node(struct device_node *np,
+ int bank_nr);
+
+int stm_of_get_nand_banks(struct device *dev, struct device_node *np,
+ struct stm_nand_bank_data **banksp);
+
+#endif /* STM_NAND_DT_H */
new file mode 100644
@@ -0,0 +1,147 @@
+/*
+ * include/linux/mtd/stm_mtd.h
+ *
+ * Support for STMicroelectronics NAND Controllers
+ *
+ * Copyright (c) 2014 STMicroelectronics Limited
+ * Author: Angus Clark <Angus.Clark@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __LINUX_STM_NAND_H
+#define __LINUX_STM_NAND_H
+
+#include <linux/io.h>
+#include <linux/mtd/nand.h>
+
+/* ECC Modes */
+enum stm_nand_bch_ecc_config {
+ BCH_18BIT_ECC = 0,
+ BCH_30BIT_ECC,
+ BCH_NO_ECC,
+ BCH_ECC_RSRV,
+ BCH_ECC_AUTO,
+};
+
+/* Bad Block Table (BBT) */
+struct nandi_bbt_info {
+ uint32_t bbt_size; /* Size of bad-block table */
+ uint32_t bbt_vers[2]; /* Version (Primary/Mirror) */
+ uint32_t bbt_block[2]; /* Block No. (Primary/Mirror) */
+ uint8_t *bbt; /* Table data */
+};
+
+/* Collection of MTD/NAND device information */
+struct nandi_info {
+ struct mtd_info mtd; /* MTD info */
+ struct nand_chip chip; /* NAND chip info */
+
+ struct nand_ecclayout ecclayout; /* MTD ECC layout */
+ struct nandi_bbt_info bbt_info; /* Bad Block Table */
+ int nr_parts; /* Number of MTD partitions */
+ struct mtd_partition *parts; /* MTD partitions */
+};
+
+/* NANDi Controller (Hamming/BCH) */
+struct nandi_controller {
+ void __iomem *base; /* Controller base*/
+ void __iomem *emiss; /* EMISS control base */
+ void __iomem *emisscfg; /* EMISS config base */
+ void __iomem *dma; /* DMA control base */
+
+ struct clk *bch_clk;
+ struct clk *emi_clk;
+ /* IRQ-triggered Completions: */
+ struct completion seq_completed; /* SEQ Over */
+ struct completion rbn_completed; /* RBn */
+
+ struct device *dev;
+
+ int bch_ecc_mode; /* ECC mode */
+ bool extra_addr; /* Extra address cycle */
+
+ uint32_t blocks_per_device;
+ uint32_t sectors_per_page;
+
+ uint8_t *buf; /* Some buffers to use */
+ uint8_t *page_buf;
+ uint8_t *oob_buf;
+ uint32_t *buf_list;
+
+ int cached_page; /* page number of page in */
+ /* 'page_buf' */
+
+ struct nandi_info info; /* NAND device info */
+};
+
+/*
+ * Board-level specification relating to a 'bank' of NAND Flash
+ */
+struct stm_nand_bank_data {
+ int csn;
+ int nr_partitions;
+ struct mtd_partition *partitions;
+ unsigned int options;
+ unsigned int bbt_options;
+
+ struct nand_sdr_timings *timing_spec;
+
+ /*
+ * No. of IP clk cycles by which to 'relax' the timing configuration.
+ * Required on some boards to to accommodate board-level limitations.
+ * Used in conjunction with 'nand_sdr_timings' and ONFI configuration.
+ */
+ int timing_relax;
+};
+
+struct stm_nand_bch_ddata {
+ struct nandi_controller *nandi;
+ struct stm_nand_bank_data *bank;
+ enum stm_nand_bch_ecc_config bch_ecc_cfg;
+};
+
+enum nandi_controllers {
+ STM_NANDI_UNCONFIGURED,
+ STM_NANDI_HAMMING,
+ STM_NANDI_BCH
+};
+
+extern int flex_read_raw(struct nandi_controller *nandi,
+ uint32_t page_addr,
+ uint32_t col_addr,
+ uint8_t *buf, uint32_t len);
+extern uint8_t bch_write_page(struct nandi_controller *nandi,
+ loff_t offs, const uint8_t *buf);
+extern uint8_t bch_erase_block(struct nandi_controller *nandi,
+ loff_t offs);
+extern int bch_read_page(struct nandi_controller *nandi,
+ loff_t offs, uint8_t *buf);
+
+#define EMISS_NAND_CONFIG_HAMMING_NOT_BCH (0x1 << 6)
+
+static inline void emiss_nandi_select(struct nandi_controller *nandi,
+ enum nandi_controllers controller)
+{
+ unsigned v;
+
+ v = readl(nandi->emisscfg);
+
+ if (controller == STM_NANDI_HAMMING) {
+ if (v & EMISS_NAND_CONFIG_HAMMING_NOT_BCH)
+ return;
+ v |= EMISS_NAND_CONFIG_HAMMING_NOT_BCH;
+ } else {
+ if (!(v & EMISS_NAND_CONFIG_HAMMING_NOT_BCH))
+ return;
+ v &= ~EMISS_NAND_CONFIG_HAMMING_NOT_BCH;
+ }
+
+ writel(v, nandi->emisscfg);
+ readl(nandi->emisscfg);
+}
+
+#endif /* __LINUX_STM_NAND_H */