| Message ID | 1336114597-11852-2-git-send-email-rajeshwari.s@samsung.com |
|---|---|
| State | New |
| Headers | show |
Hi, On 4 May 2012 12:26, Rajeshwari Shinde <rajeshwari.s@samsung.com> wrote: > Use the pinmux configuration function for SMDK5250. > > Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> > Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> > --- > arch/arm/cpu/armv7/exynos/Makefile | 2 +- > board/samsung/smdk5250/smdk5250.c | 160 ++++++------------------------------ > 2 files changed, 26 insertions(+), 136 deletions(-) > > diff --git a/arch/arm/cpu/armv7/exynos/Makefile b/arch/arm/cpu/armv7/exynos/Makefile > index 90ec2bd..9119961 100644 > --- a/arch/arm/cpu/armv7/exynos/Makefile > +++ b/arch/arm/cpu/armv7/exynos/Makefile > @@ -22,7 +22,7 @@ include $(TOPDIR)/config.mk > > LIB = $(obj)lib$(SOC).o > > -COBJS += clock.o power.o soc.o system.o > +COBJS += clock.o power.o soc.o system.o pinmux.o > > SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) > OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) > diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c > index 32786e2..4c0398d 100644 > --- a/board/samsung/smdk5250/smdk5250.c > +++ b/board/samsung/smdk5250/smdk5250.c > @@ -26,6 +26,7 @@ > #include <asm/arch/cpu.h> > #include <asm/arch/gpio.h> > #include <asm/arch/mmc.h> > +#include <asm/arch/pinmux.h> > #include <asm/arch/sromc.h> > > DECLARE_GLOBAL_DATA_PTR; > @@ -35,72 +36,7 @@ struct exynos5_gpio_part1 *gpio1; Do we need this declaration as gpio init is done using pinmux. And remove the same from board_init. > static void smc9115_pre_init(void) > { > u32 smc_bw_conf, smc_bc_conf; > - int i; > - > - /* > - * SROM:CS1 and EBI > - * > - * GPY0[0] SROM_CSn[0] > - * GPY0[1] SROM_CSn[1](2) > - * GPY0[2] SROM_CSn[2] > - * GPY0[3] SROM_CSn[3] > - * GPY0[4] EBI_OEn(2) > - * GPY0[5] EBI_EEn(2) > - * > - * GPY1[0] EBI_BEn[0](2) > - * GPY1[1] EBI_BEn[1](2) > - * GPY1[2] SROM_WAIT(2) > - * GPY1[3] EBI_DATA_RDn(2) > - */ > - s5p_gpio_cfg_pin(&gpio1->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2)); > - s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2)); > - s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2)); > - > - for (i = 0; i < 4; i++) > - s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2)); > - > - /* > - * EBI: 8 Addrss Lines > - * > - * GPY3[0] EBI_ADDR[0](2) > - * GPY3[1] EBI_ADDR[1](2) > - * GPY3[2] EBI_ADDR[2](2) > - * GPY3[3] EBI_ADDR[3](2) > - * GPY3[4] EBI_ADDR[4](2) > - * GPY3[5] EBI_ADDR[5](2) > - * GPY3[6] EBI_ADDR[6](2) > - * GPY3[7] EBI_ADDR[7](2) > - * > - * EBI: 16 Data Lines > - * > - * GPY5[0] EBI_DATA[0](2) > - * GPY5[1] EBI_DATA[1](2) > - * GPY5[2] EBI_DATA[2](2) > - * GPY5[3] EBI_DATA[3](2) > - * GPY5[4] EBI_DATA[4](2) > - * GPY5[5] EBI_DATA[5](2) > - * GPY5[6] EBI_DATA[6](2) > - * GPY5[7] EBI_DATA[7](2) > - * > - * GPY6[0] EBI_DATA[8](2) > - * GPY6[1] EBI_DATA[9](2) > - * GPY6[2] EBI_DATA[10](2) > - * GPY6[3] EBI_DATA[11](2) > - * GPY6[4] EBI_DATA[12](2) > - * GPY6[5] EBI_DATA[13](2) > - * GPY6[6] EBI_DATA[14](2) > - * GPY6[7] EBI_DATA[15](2) > - */ > - for (i = 0; i < 8; i++) { > - s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2)); > - s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP); > - > - s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2)); > - s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP); > - > - s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2)); > - s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP); > - } > + int err; > > /* Ethernet needs data bus width of 16 bits */ > smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK) > @@ -112,6 +48,11 @@ static void smc9115_pre_init(void) > | SROMC_BC_PMC(0x01); > > /* Select and configure the SROMC bank */ > + err = exynos_pinmux_config(PERIPH_ID_SROMC, > + CONFIG_ENV_SROM_BANK | PINMUX_FLAG_16BIT); > + if (err < 0) > + debug("SROMC not configured\n"); > + > s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf); > } > #endif > @@ -186,31 +127,12 @@ int checkboard(void) > #ifdef CONFIG_GENERIC_MMC > int board_mmc_init(bd_t *bis) > { > - int i, err; > - > - /* > - * MMC2 SD card GPIO: > - * > - * GPC2[0] SD_2_CLK(2) > - * GPC2[1] SD_2_CMD(2) > - * GPC2[2] SD_2_CDn > - * GPC2[3:6] SD_2_DATA[0:3](2) > - */ > - for (i = 0; i < 7; i++) { > - /* GPC2[0:6] special function 2 */ > - s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2)); > + int err; > > - /* GPK2[0:6] drv 4x */ > - s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X); > - > - /* GPK2[0:1] pull disable */ > - if (i == 0 || i == 1) { > - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_NONE); > - continue; > - } > - > - /* GPK2[2:6] pull up */ > - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP); > + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); > + if (err < 0) { > + debug("SDMMC2 not configured\n"); > + return err; > } > > err = s5p_mmc_init(2, 4); > @@ -220,55 +142,23 @@ int board_mmc_init(bd_t *bis) > > static void board_uart_init(void) > { > - struct exynos5_gpio_part1 *gpio1 = > - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); > - int i; > + int err; > > - /* > - * UART0 GPIOs : GPA0CON[3:0] 0x2222 > - * Must set CFG17 switches to select UART0 to use. > - */ > - for (i = 0; i <= 3; i++) { > - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); > - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); > - } > + err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); > + if (err < 0) > + debug("UART0 not configured\n"); > > - /* > - * UART1 GPIOs : GPA0CON[5:4] 0x22 > - * Must set CFG17 switches to select UART1 to use. > - * > - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down > - * in order to use them (so that those pins can be used for I2C). > - */ > - for (i = 4; i <= 5; i++) { > - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); > - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); > - } > + err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); > + if (err < 0) > + debug("UART1 not configured\n"); > > - /* > - * UART2 GPIOs : GPA1CON[1:0] 0x22 > - * Must set CFG17 switches to select UART2 to use. > - * > - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down > - * in order to use them (so that those pins can be used for I2C). > - */ > - for (i = 0; i <= 1; i++) { > - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); > - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); > - } > - > - /* > - * UART3 GPIOs : GPA1CON[5:4] 0x22 > - * Must set CFG16 switches to select UART3 to use. > - */ > - for (i = 4; i <= 5; i++) { > - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); > - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); > - } > + err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); > + if (err < 0) > + debug("UART2 not configured\n"); > > - /* > - * There's no mux for UART4--it's internal only > - */ > + err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); > + if (err < 0) > + debug("UART3 not configured\n"); > } > > #ifdef CONFIG_BOARD_EARLY_INIT_F > -- > 1.7.4.4 > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot
Hi Chander, Thank you for comments On Wed, May 23, 2012 at 11:35 AM, Chander Kashyap <chander.kashyap@linaro.org> wrote: > Hi, > > On 4 May 2012 12:26, Rajeshwari Shinde <rajeshwari.s@samsung.com> wrote: >> Use the pinmux configuration function for SMDK5250. >> >> Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> >> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> >> --- >> arch/arm/cpu/armv7/exynos/Makefile | 2 +- >> board/samsung/smdk5250/smdk5250.c | 160 ++++++------------------------------ >> 2 files changed, 26 insertions(+), 136 deletions(-) >> >> diff --git a/arch/arm/cpu/armv7/exynos/Makefile b/arch/arm/cpu/armv7/exynos/Makefile >> index 90ec2bd..9119961 100644 >> --- a/arch/arm/cpu/armv7/exynos/Makefile >> +++ b/arch/arm/cpu/armv7/exynos/Makefile >> @@ -22,7 +22,7 @@ include $(TOPDIR)/config.mk >> >> LIB = $(obj)lib$(SOC).o >> >> -COBJS += clock.o power.o soc.o system.o >> +COBJS += clock.o power.o soc.o system.o pinmux.o >> >> SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) >> OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) >> diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c >> index 32786e2..4c0398d 100644 >> --- a/board/samsung/smdk5250/smdk5250.c >> +++ b/board/samsung/smdk5250/smdk5250.c >> @@ -26,6 +26,7 @@ >> #include <asm/arch/cpu.h> >> #include <asm/arch/gpio.h> >> #include <asm/arch/mmc.h> >> +#include <asm/arch/pinmux.h> >> #include <asm/arch/sromc.h> >> >> DECLARE_GLOBAL_DATA_PTR; >> @@ -35,72 +36,7 @@ struct exynos5_gpio_part1 *gpio1; > Do we need this declaration as gpio init is done using pinmux. > And remove the same from board_init. - will do so >> static void smc9115_pre_init(void) >> { >> u32 smc_bw_conf, smc_bc_conf; >> - int i; >> - >> - /* >> - * SROM:CS1 and EBI >> - * >> - * GPY0[0] SROM_CSn[0] >> - * GPY0[1] SROM_CSn[1](2) >> - * GPY0[2] SROM_CSn[2] >> - * GPY0[3] SROM_CSn[3] >> - * GPY0[4] EBI_OEn(2) >> - * GPY0[5] EBI_EEn(2) >> - * >> - * GPY1[0] EBI_BEn[0](2) >> - * GPY1[1] EBI_BEn[1](2) >> - * GPY1[2] SROM_WAIT(2) >> - * GPY1[3] EBI_DATA_RDn(2) >> - */ >> - s5p_gpio_cfg_pin(&gpio1->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2)); >> - s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2)); >> - s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2)); >> - >> - for (i = 0; i < 4; i++) >> - s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2)); >> - >> - /* >> - * EBI: 8 Addrss Lines >> - * >> - * GPY3[0] EBI_ADDR[0](2) >> - * GPY3[1] EBI_ADDR[1](2) >> - * GPY3[2] EBI_ADDR[2](2) >> - * GPY3[3] EBI_ADDR[3](2) >> - * GPY3[4] EBI_ADDR[4](2) >> - * GPY3[5] EBI_ADDR[5](2) >> - * GPY3[6] EBI_ADDR[6](2) >> - * GPY3[7] EBI_ADDR[7](2) >> - * >> - * EBI: 16 Data Lines >> - * >> - * GPY5[0] EBI_DATA[0](2) >> - * GPY5[1] EBI_DATA[1](2) >> - * GPY5[2] EBI_DATA[2](2) >> - * GPY5[3] EBI_DATA[3](2) >> - * GPY5[4] EBI_DATA[4](2) >> - * GPY5[5] EBI_DATA[5](2) >> - * GPY5[6] EBI_DATA[6](2) >> - * GPY5[7] EBI_DATA[7](2) >> - * >> - * GPY6[0] EBI_DATA[8](2) >> - * GPY6[1] EBI_DATA[9](2) >> - * GPY6[2] EBI_DATA[10](2) >> - * GPY6[3] EBI_DATA[11](2) >> - * GPY6[4] EBI_DATA[12](2) >> - * GPY6[5] EBI_DATA[13](2) >> - * GPY6[6] EBI_DATA[14](2) >> - * GPY6[7] EBI_DATA[15](2) >> - */ >> - for (i = 0; i < 8; i++) { >> - s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2)); >> - s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP); >> - >> - s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2)); >> - s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP); >> - >> - s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2)); >> - s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP); >> - } >> + int err; >> >> /* Ethernet needs data bus width of 16 bits */ >> smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK) >> @@ -112,6 +48,11 @@ static void smc9115_pre_init(void) >> | SROMC_BC_PMC(0x01); >> >> /* Select and configure the SROMC bank */ >> + err = exynos_pinmux_config(PERIPH_ID_SROMC, >> + CONFIG_ENV_SROM_BANK | PINMUX_FLAG_16BIT); >> + if (err < 0) >> + debug("SROMC not configured\n"); >> + >> s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf); >> } >> #endif >> @@ -186,31 +127,12 @@ int checkboard(void) >> #ifdef CONFIG_GENERIC_MMC >> int board_mmc_init(bd_t *bis) >> { >> - int i, err; >> - >> - /* >> - * MMC2 SD card GPIO: >> - * >> - * GPC2[0] SD_2_CLK(2) >> - * GPC2[1] SD_2_CMD(2) >> - * GPC2[2] SD_2_CDn >> - * GPC2[3:6] SD_2_DATA[0:3](2) >> - */ >> - for (i = 0; i < 7; i++) { >> - /* GPC2[0:6] special function 2 */ >> - s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2)); >> + int err; >> >> - /* GPK2[0:6] drv 4x */ >> - s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X); >> - >> - /* GPK2[0:1] pull disable */ >> - if (i == 0 || i == 1) { >> - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_NONE); >> - continue; >> - } >> - >> - /* GPK2[2:6] pull up */ >> - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP); >> + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); >> + if (err < 0) { >> + debug("SDMMC2 not configured\n"); >> + return err; >> } >> >> err = s5p_mmc_init(2, 4); >> @@ -220,55 +142,23 @@ int board_mmc_init(bd_t *bis) >> >> static void board_uart_init(void) >> { >> - struct exynos5_gpio_part1 *gpio1 = >> - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); >> - int i; >> + int err; >> >> - /* >> - * UART0 GPIOs : GPA0CON[3:0] 0x2222 >> - * Must set CFG17 switches to select UART0 to use. >> - */ >> - for (i = 0; i <= 3; i++) { >> - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); >> - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); >> - } >> + err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); >> + if (err < 0) >> + debug("UART0 not configured\n"); >> >> - /* >> - * UART1 GPIOs : GPA0CON[5:4] 0x22 >> - * Must set CFG17 switches to select UART1 to use. >> - * >> - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down >> - * in order to use them (so that those pins can be used for I2C). >> - */ >> - for (i = 4; i <= 5; i++) { >> - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); >> - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); >> - } >> + err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); >> + if (err < 0) >> + debug("UART1 not configured\n"); >> >> - /* >> - * UART2 GPIOs : GPA1CON[1:0] 0x22 >> - * Must set CFG17 switches to select UART2 to use. >> - * >> - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down >> - * in order to use them (so that those pins can be used for I2C). >> - */ >> - for (i = 0; i <= 1; i++) { >> - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); >> - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); >> - } >> - >> - /* >> - * UART3 GPIOs : GPA1CON[5:4] 0x22 >> - * Must set CFG16 switches to select UART3 to use. >> - */ >> - for (i = 4; i <= 5; i++) { >> - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); >> - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); >> - } >> + err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); >> + if (err < 0) >> + debug("UART2 not configured\n"); >> >> - /* >> - * There's no mux for UART4--it's internal only >> - */ >> + err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); >> + if (err < 0) >> + debug("UART3 not configured\n"); >> } >> >> #ifdef CONFIG_BOARD_EARLY_INIT_F >> -- >> 1.7.4.4 >> >> _______________________________________________ >> U-Boot mailing list >> U-Boot@lists.denx.de >> http://lists.denx.de/mailman/listinfo/u-boot > > > > -- > with warm regards, > Chander Kashyap > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot Regards, Rajeshwari Shinde
Hi, On Wed, May 23, 2012 at 1:49 AM, Rajeshwari Birje < rajeshwari.birje@gmail.com> wrote: > Hi Chander, > > Thank you for comments > > On Wed, May 23, 2012 at 11:35 AM, Chander Kashyap > <chander.kashyap@linaro.org> wrote: > > Hi, > > > > On 4 May 2012 12:26, Rajeshwari Shinde <rajeshwari.s@samsung.com> wrote: > >> Use the pinmux configuration function for SMDK5250. > >> > >> Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> > >> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> > >> --- > >> arch/arm/cpu/armv7/exynos/Makefile | 2 +- > >> board/samsung/smdk5250/smdk5250.c | 160 > ++++++------------------------------ > >> 2 files changed, 26 insertions(+), 136 deletions(-) > >> > >> diff --git a/arch/arm/cpu/armv7/exynos/Makefile > b/arch/arm/cpu/armv7/exynos/Makefile > >> index 90ec2bd..9119961 100644 > >> --- a/arch/arm/cpu/armv7/exynos/Makefile > >> +++ b/arch/arm/cpu/armv7/exynos/Makefile > >> @@ -22,7 +22,7 @@ include $(TOPDIR)/config.mk > >> > >> LIB = $(obj)lib$(SOC).o > >> > >> -COBJS += clock.o power.o soc.o system.o > >> +COBJS += clock.o power.o soc.o system.o pinmux.o > >> > >> SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) > >> OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) > >> diff --git a/board/samsung/smdk5250/smdk5250.c > b/board/samsung/smdk5250/smdk5250.c > >> index 32786e2..4c0398d 100644 > >> --- a/board/samsung/smdk5250/smdk5250.c > >> +++ b/board/samsung/smdk5250/smdk5250.c > >> @@ -26,6 +26,7 @@ > >> #include <asm/arch/cpu.h> > >> #include <asm/arch/gpio.h> > >> #include <asm/arch/mmc.h> > >> +#include <asm/arch/pinmux.h> > >> #include <asm/arch/sromc.h> > >> > >> DECLARE_GLOBAL_DATA_PTR; > >> @@ -35,72 +36,7 @@ struct exynos5_gpio_part1 *gpio1; > > Do we need this declaration as gpio init is done using pinmux. > > And remove the same from board_init. > - will do so > >> static void smc9115_pre_init(void) > >> { > >> u32 smc_bw_conf, smc_bc_conf; > >> - int i; > >> - > >> - /* > >> - * SROM:CS1 and EBI > >> - * > >> - * GPY0[0] SROM_CSn[0] > >> - * GPY0[1] SROM_CSn[1](2) > >> - * GPY0[2] SROM_CSn[2] > >> - * GPY0[3] SROM_CSn[3] > >> - * GPY0[4] EBI_OEn(2) > >> - * GPY0[5] EBI_EEn(2) > >> - * > >> - * GPY1[0] EBI_BEn[0](2) > >> - * GPY1[1] EBI_BEn[1](2) > >> - * GPY1[2] SROM_WAIT(2) > >> - * GPY1[3] EBI_DATA_RDn(2) > >> - */ > >> - s5p_gpio_cfg_pin(&gpio1->y0, CONFIG_ENV_SROM_BANK, > GPIO_FUNC(2)); > >> - s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2)); > >> - s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2)); > >> - > >> - for (i = 0; i < 4; i++) > >> - s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2)); > >> - > >> - /* > >> - * EBI: 8 Addrss Lines > >> - * > >> - * GPY3[0] EBI_ADDR[0](2) > >> - * GPY3[1] EBI_ADDR[1](2) > >> - * GPY3[2] EBI_ADDR[2](2) > >> - * GPY3[3] EBI_ADDR[3](2) > >> - * GPY3[4] EBI_ADDR[4](2) > >> - * GPY3[5] EBI_ADDR[5](2) > >> - * GPY3[6] EBI_ADDR[6](2) > >> - * GPY3[7] EBI_ADDR[7](2) > >> - * > >> - * EBI: 16 Data Lines > >> - * > >> - * GPY5[0] EBI_DATA[0](2) > >> - * GPY5[1] EBI_DATA[1](2) > >> - * GPY5[2] EBI_DATA[2](2) > >> - * GPY5[3] EBI_DATA[3](2) > >> - * GPY5[4] EBI_DATA[4](2) > >> - * GPY5[5] EBI_DATA[5](2) > >> - * GPY5[6] EBI_DATA[6](2) > >> - * GPY5[7] EBI_DATA[7](2) > >> - * > >> - * GPY6[0] EBI_DATA[8](2) > >> - * GPY6[1] EBI_DATA[9](2) > >> - * GPY6[2] EBI_DATA[10](2) > >> - * GPY6[3] EBI_DATA[11](2) > >> - * GPY6[4] EBI_DATA[12](2) > >> - * GPY6[5] EBI_DATA[13](2) > >> - * GPY6[6] EBI_DATA[14](2) > >> - * GPY6[7] EBI_DATA[15](2) > >> - */ > >> - for (i = 0; i < 8; i++) { > >> - s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2)); > >> - s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP); > >> - > >> - s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2)); > >> - s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP); > >> - > >> - s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2)); > >> - s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP); > >> - } > >> + int err; > >> > >> /* Ethernet needs data bus width of 16 bits */ > >> smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK) > >> @@ -112,6 +48,11 @@ static void smc9115_pre_init(void) > >> | SROMC_BC_PMC(0x01); > >> > >> /* Select and configure the SROMC bank */ > >> + err = exynos_pinmux_config(PERIPH_ID_SROMC, > >> + CONFIG_ENV_SROM_BANK | > PINMUX_FLAG_16BIT); > >> + if (err < 0) > >> + debug("SROMC not configured\n"); > Perhaps return -1 here? > >> + > >> s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf); > >> } > >> #endif > >> @@ -186,31 +127,12 @@ int checkboard(void) > >> #ifdef CONFIG_GENERIC_MMC > >> int board_mmc_init(bd_t *bis) > >> { > >> - int i, err; > >> - > >> - /* > >> - * MMC2 SD card GPIO: > >> - * > >> - * GPC2[0] SD_2_CLK(2) > >> - * GPC2[1] SD_2_CMD(2) > >> - * GPC2[2] SD_2_CDn > >> - * GPC2[3:6] SD_2_DATA[0:3](2) > >> - */ > >> - for (i = 0; i < 7; i++) { > >> - /* GPC2[0:6] special function 2 */ > >> - s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2)); > >> + int err; > >> > >> - /* GPK2[0:6] drv 4x */ > >> - s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X); > >> - > >> - /* GPK2[0:1] pull disable */ > >> - if (i == 0 || i == 1) { > >> - s5p_gpio_set_pull(&gpio1->c2, i, > GPIO_PULL_NONE); > >> - continue; > >> - } > >> - > >> - /* GPK2[2:6] pull up */ > >> - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP); > >> + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); > >> + if (err < 0) { > >> + debug("SDMMC2 not configured\n"); > >> + return err; > >> } > >> > >> err = s5p_mmc_init(2, 4); > >> @@ -220,55 +142,23 @@ int board_mmc_init(bd_t *bis) > >> > >> static void board_uart_init(void) > >> { > >> - struct exynos5_gpio_part1 *gpio1 = > >> - (struct exynos5_gpio_part1 *) > samsung_get_base_gpio_part1(); > >> - int i; > >> + int err; > >> > >> - /* > >> - * UART0 GPIOs : GPA0CON[3:0] 0x2222 > >> - * Must set CFG17 switches to select UART0 to use. > >> - */ > >> - for (i = 0; i <= 3; i++) { > >> - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); > >> - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); > >> - } > >> + err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); > >> + if (err < 0) > >> + debug("UART0 not configured\n"); > >> > >> - /* > >> - * UART1 GPIOs : GPA0CON[5:4] 0x22 > >> - * Must set CFG17 switches to select UART1 to use. > >> - * > >> - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered > down > >> - * in order to use them (so that those pins can be used for > I2C). > >> - */ > >> - for (i = 4; i <= 5; i++) { > >> - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); > >> - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); > >> - } > >> + err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); > >> + if (err < 0) > >> + debug("UART1 not configured\n"); > >> > >> - /* > >> - * UART2 GPIOs : GPA1CON[1:0] 0x22 > >> - * Must set CFG17 switches to select UART2 to use. > >> - * > >> - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered > down > >> - * in order to use them (so that those pins can be used for > I2C). > >> - */ > >> - for (i = 0; i <= 1; i++) { > >> - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); > >> - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); > >> - } > >> - > >> - /* > >> - * UART3 GPIOs : GPA1CON[5:4] 0x22 > >> - * Must set CFG16 switches to select UART3 to use. > >> - */ > >> - for (i = 4; i <= 5; i++) { > >> - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); > >> - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); > >> - } > >> + err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); > >> + if (err < 0) > >> + debug("UART2 not configured\n"); > >> > >> - /* > >> - * There's no mux for UART4--it's internal only > >> - */ > >> + err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); > >> + if (err < 0) > >> + debug("UART3 not configured\n"); > >> } > >> > >> #ifdef CONFIG_BOARD_EARLY_INIT_F > >> -- > >> 1.7.4.4 > >> > >> _______________________________________________ > >> U-Boot mailing list > >> U-Boot@lists.denx.de > >> http://lists.denx.de/mailman/listinfo/u-boot > > > > > > > > -- > > with warm regards, > > Chander Kashyap > > _______________________________________________ > > U-Boot mailing list > > U-Boot@lists.denx.de > > http://lists.denx.de/mailman/listinfo/u-boot > > Regards, > Rajeshwari Shinde > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot >
diff --git a/arch/arm/cpu/armv7/exynos/Makefile b/arch/arm/cpu/armv7/exynos/Makefile index 90ec2bd..9119961 100644 --- a/arch/arm/cpu/armv7/exynos/Makefile +++ b/arch/arm/cpu/armv7/exynos/Makefile @@ -22,7 +22,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(SOC).o -COBJS += clock.o power.o soc.o system.o +COBJS += clock.o power.o soc.o system.o pinmux.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index 32786e2..4c0398d 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -26,6 +26,7 @@ #include <asm/arch/cpu.h> #include <asm/arch/gpio.h> #include <asm/arch/mmc.h> +#include <asm/arch/pinmux.h> #include <asm/arch/sromc.h> DECLARE_GLOBAL_DATA_PTR; @@ -35,72 +36,7 @@ struct exynos5_gpio_part1 *gpio1; static void smc9115_pre_init(void) { u32 smc_bw_conf, smc_bc_conf; - int i; - - /* - * SROM:CS1 and EBI - * - * GPY0[0] SROM_CSn[0] - * GPY0[1] SROM_CSn[1](2) - * GPY0[2] SROM_CSn[2] - * GPY0[3] SROM_CSn[3] - * GPY0[4] EBI_OEn(2) - * GPY0[5] EBI_EEn(2) - * - * GPY1[0] EBI_BEn[0](2) - * GPY1[1] EBI_BEn[1](2) - * GPY1[2] SROM_WAIT(2) - * GPY1[3] EBI_DATA_RDn(2) - */ - s5p_gpio_cfg_pin(&gpio1->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2)); - s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2)); - s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2)); - - for (i = 0; i < 4; i++) - s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2)); - - /* - * EBI: 8 Addrss Lines - * - * GPY3[0] EBI_ADDR[0](2) - * GPY3[1] EBI_ADDR[1](2) - * GPY3[2] EBI_ADDR[2](2) - * GPY3[3] EBI_ADDR[3](2) - * GPY3[4] EBI_ADDR[4](2) - * GPY3[5] EBI_ADDR[5](2) - * GPY3[6] EBI_ADDR[6](2) - * GPY3[7] EBI_ADDR[7](2) - * - * EBI: 16 Data Lines - * - * GPY5[0] EBI_DATA[0](2) - * GPY5[1] EBI_DATA[1](2) - * GPY5[2] EBI_DATA[2](2) - * GPY5[3] EBI_DATA[3](2) - * GPY5[4] EBI_DATA[4](2) - * GPY5[5] EBI_DATA[5](2) - * GPY5[6] EBI_DATA[6](2) - * GPY5[7] EBI_DATA[7](2) - * - * GPY6[0] EBI_DATA[8](2) - * GPY6[1] EBI_DATA[9](2) - * GPY6[2] EBI_DATA[10](2) - * GPY6[3] EBI_DATA[11](2) - * GPY6[4] EBI_DATA[12](2) - * GPY6[5] EBI_DATA[13](2) - * GPY6[6] EBI_DATA[14](2) - * GPY6[7] EBI_DATA[15](2) - */ - for (i = 0; i < 8; i++) { - s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2)); - s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP); - - s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2)); - s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP); - - s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2)); - s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP); - } + int err; /* Ethernet needs data bus width of 16 bits */ smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK) @@ -112,6 +48,11 @@ static void smc9115_pre_init(void) | SROMC_BC_PMC(0x01); /* Select and configure the SROMC bank */ + err = exynos_pinmux_config(PERIPH_ID_SROMC, + CONFIG_ENV_SROM_BANK | PINMUX_FLAG_16BIT); + if (err < 0) + debug("SROMC not configured\n"); + s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf); } #endif @@ -186,31 +127,12 @@ int checkboard(void) #ifdef CONFIG_GENERIC_MMC int board_mmc_init(bd_t *bis) { - int i, err; - - /* - * MMC2 SD card GPIO: - * - * GPC2[0] SD_2_CLK(2) - * GPC2[1] SD_2_CMD(2) - * GPC2[2] SD_2_CDn - * GPC2[3:6] SD_2_DATA[0:3](2) - */ - for (i = 0; i < 7; i++) { - /* GPC2[0:6] special function 2 */ - s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2)); + int err; - /* GPK2[0:6] drv 4x */ - s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X); - - /* GPK2[0:1] pull disable */ - if (i == 0 || i == 1) { - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_NONE); - continue; - } - - /* GPK2[2:6] pull up */ - s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP); + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); + if (err < 0) { + debug("SDMMC2 not configured\n"); + return err; } err = s5p_mmc_init(2, 4); @@ -220,55 +142,23 @@ int board_mmc_init(bd_t *bis) static void board_uart_init(void) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); - int i; + int err; - /* - * UART0 GPIOs : GPA0CON[3:0] 0x2222 - * Must set CFG17 switches to select UART0 to use. - */ - for (i = 0; i <= 3; i++) { - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); - } + err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); + if (err < 0) + debug("UART0 not configured\n"); - /* - * UART1 GPIOs : GPA0CON[5:4] 0x22 - * Must set CFG17 switches to select UART1 to use. - * - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down - * in order to use them (so that those pins can be used for I2C). - */ - for (i = 4; i <= 5; i++) { - s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); - } + err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); + if (err < 0) + debug("UART1 not configured\n"); - /* - * UART2 GPIOs : GPA1CON[1:0] 0x22 - * Must set CFG17 switches to select UART2 to use. - * - * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down - * in order to use them (so that those pins can be used for I2C). - */ - for (i = 0; i <= 1; i++) { - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); - } - - /* - * UART3 GPIOs : GPA1CON[5:4] 0x22 - * Must set CFG16 switches to select UART3 to use. - */ - for (i = 4; i <= 5; i++) { - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); - } + err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); + if (err < 0) + debug("UART2 not configured\n"); - /* - * There's no mux for UART4--it's internal only - */ + err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); + if (err < 0) + debug("UART3 not configured\n"); } #ifdef CONFIG_BOARD_EARLY_INIT_F