Message ID | 1403103172-19856-1-git-send-email-lee.jones@linaro.org |
---|---|
State | New |
Headers | show |
Hi Lee, minor remark below.. On 18 June 2014 16:52, Lee Jones <lee.jones@linaro.org> wrote: > Supply top level nodes for the STiH407 based development boards. > The Pinctrl configuration has already been applied, so the only > missing piece of the DT puzzle is for a board's DTB to enable > the nodes. > > Signed-off-by: Lee Jones <lee.jones@linaro.org> > --- > arch/arm/boot/dts/stih407.dtsi | 27 +++++++++++++++++++++++++++ > 1 file changed, 27 insertions(+) > > diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/stih407.dtsi > index 4f9024f..6b43ba2 100644 > --- a/arch/arm/boot/dts/stih407.dtsi > +++ b/arch/arm/boot/dts/stih407.dtsi > @@ -259,5 +259,32 @@ > > status = "disabled"; > }; > + > + /* COMMS PWM Module */ > + pwm0: pwm@9810000 { > + compatible = "st,sti-pwm"; > + status = "disabled"; > + #pwm-cells = <2>; > + reg = <0x9810000 0x68>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm0_chan0_default>; del space > + clock-names = "pwm"; > + clocks = <&clk_sysin>; > + }; > + > + /* SBC PWM Module */ > + pwm1: pwm@9510000 { > + compatible = "st,sti-pwm"; > + status = "disabled"; > + #pwm-cells = <2>; > + reg = <0x9510000 0x68>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm1_chan0_default > + &pinctrl_pwm1_chan1_default > + &pinctrl_pwm1_chan2_default > + &pinctrl_pwm1_chan3_default>; > + clock-names = "pwm"; > + clocks = <&clk_sysin>; > + }; > }; > }; > -- > 1.8.3.2 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
On Wed, 18 Jun 2014, Gabriel Fernandez wrote: > Hi Lee, > minor remark below.. > > On 18 June 2014 16:52, Lee Jones <lee.jones@linaro.org> wrote: > > Supply top level nodes for the STiH407 based development boards. > > The Pinctrl configuration has already been applied, so the only > > missing piece of the DT puzzle is for a board's DTB to enable > > the nodes. > > > > Signed-off-by: Lee Jones <lee.jones@linaro.org> > > --- > > arch/arm/boot/dts/stih407.dtsi | 27 +++++++++++++++++++++++++++ > > 1 file changed, 27 insertions(+) > > > > diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/stih407.dtsi > > index 4f9024f..6b43ba2 100644 > > --- a/arch/arm/boot/dts/stih407.dtsi > > +++ b/arch/arm/boot/dts/stih407.dtsi > > @@ -259,5 +259,32 @@ > > > > status = "disabled"; > > }; > > + > > + /* COMMS PWM Module */ > > + pwm0: pwm@9810000 { > > + compatible = "st,sti-pwm"; > > + status = "disabled"; > > + #pwm-cells = <2>; > > + reg = <0x9810000 0x68>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_pwm0_chan0_default>; > del space Fixing, thanks. > > + clock-names = "pwm"; > > + clocks = <&clk_sysin>; > > + }; > > + > > + /* SBC PWM Module */ > > + pwm1: pwm@9510000 { > > + compatible = "st,sti-pwm"; > > + status = "disabled"; > > + #pwm-cells = <2>; > > + reg = <0x9510000 0x68>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_pwm1_chan0_default > > + &pinctrl_pwm1_chan1_default > > + &pinctrl_pwm1_chan2_default > > + &pinctrl_pwm1_chan3_default>; > > + clock-names = "pwm"; > > + clocks = <&clk_sysin>; > > + }; > > }; > > }; > > > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Lee, > + /* SBC PWM Module */ > + pwm1: pwm@9510000 { > + compatible = "st,sti-pwm"; > + status = "disabled"; > + #pwm-cells = <2>; > + reg = <0x9510000 0x68>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm1_chan0_default > + &pinctrl_pwm1_chan1_default > + &pinctrl_pwm1_chan2_default > + &pinctrl_pwm1_chan3_default>; If you're passing pin config for 4 channels, I think you should also be using the 'st,pwm-num-chan = <4>' property like the doc example in patch 7. After that: Acked-by: Peter Griffin <peter.griffin@linaro.org> regards, Peter. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/stih407.dtsi index 4f9024f..6b43ba2 100644 --- a/arch/arm/boot/dts/stih407.dtsi +++ b/arch/arm/boot/dts/stih407.dtsi @@ -259,5 +259,32 @@ status = "disabled"; }; + + /* COMMS PWM Module */ + pwm0: pwm@9810000 { + compatible = "st,sti-pwm"; + status = "disabled"; + #pwm-cells = <2>; + reg = <0x9810000 0x68>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_chan0_default>; + clock-names = "pwm"; + clocks = <&clk_sysin>; + }; + + /* SBC PWM Module */ + pwm1: pwm@9510000 { + compatible = "st,sti-pwm"; + status = "disabled"; + #pwm-cells = <2>; + reg = <0x9510000 0x68>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1_chan0_default + &pinctrl_pwm1_chan1_default + &pinctrl_pwm1_chan2_default + &pinctrl_pwm1_chan3_default>; + clock-names = "pwm"; + clocks = <&clk_sysin>; + }; }; };
Supply top level nodes for the STiH407 based development boards. The Pinctrl configuration has already been applied, so the only missing piece of the DT puzzle is for a board's DTB to enable the nodes. Signed-off-by: Lee Jones <lee.jones@linaro.org> --- arch/arm/boot/dts/stih407.dtsi | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)